| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add support to deselect the mux when there is a timeout.
The mux idle_state settings will be configured on startup. In case of
MCTP it is MUX_IDLE_DISCONNECT. But when there is a timeout, mux ends
up in connected position and the devices behind the mux will appear under
different muxes connected to the same bus. This change fix the same.
Signed-off-by: Arun P. Mohanan <arun.p.m@linux.intel.com>
|
|
https://github.com/openbmc/linux into openbmc/linux_5.15.24_bump
Signed-off-by: Sujoy Ray <sujoy.ray@intel.com>
|
|
When I2C_M_RECV_LEN flag is set, the first byte of return data is the
received data length. Fix the handling of i2c_smbus_read_block_data in
aspeed i2c driver to include the received data length.
Signed-off-by: Zhikui Ren <zhikui.ren@intel.com>
|
|
[ Upstream commit d52097010078c1844348dc0e467305e5f90fd317 ]
The data type of hcnt and lcnt in the struct dw_i2c_dev is of type u16.
It's better to have same data type in struct dw_scl_sda_cfg as well.
Reported-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ebe82cf92cd4825c3029434cabfcd2f1780e64be ]
Current I2C reset procedure is broken in two ways:
1) It only generate 1 START instead of 9 STARTs and STOP.
2) It leaves the bus Busy so every I2C xfer after the first
fixup calls the reset routine again, for every xfer there after.
This fixes both errors.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit effa453168a7eeb8a562ff4edc1dbf9067360a61 ]
If an invalid block size is provided, reject it instead of silently
changing it to a supported value. Especially critical I see the case of
a write transfer with block length 0. In this case we have no guarantee
that the byte we would write is valid. When silently reducing a read to
32 bytes then we don't return an error and the caller may falsely
assume that we returned the full requested data.
If this change should break any (broken) caller, then I think we should
fix the caller.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 72a4a87da8f7bcf868b338615a814b6542f277f3 upstream.
When performing an I2C transfer where the last message was a write KASAN
would complain:
BUG: KASAN: slab-out-of-bounds in mpc_i2c_do_action+0x154/0x630
Read of size 2 at addr c814e310 by task swapper/2/0
CPU: 2 PID: 0 Comm: swapper/2 Tainted: G B 5.16.0-rc8 #1
Call Trace:
[e5ee9d50] [c08418e8] dump_stack_lvl+0x4c/0x6c (unreliable)
[e5ee9d70] [c02f8a14] print_address_description.constprop.13+0x64/0x3b0
[e5ee9da0] [c02f9030] kasan_report+0x1f0/0x204
[e5ee9de0] [c0c76ee4] mpc_i2c_do_action+0x154/0x630
[e5ee9e30] [c0c782c4] mpc_i2c_isr+0x164/0x240
[e5ee9e60] [c00f3a04] __handle_irq_event_percpu+0xf4/0x3b0
[e5ee9ec0] [c00f3d40] handle_irq_event_percpu+0x80/0x110
[e5ee9f40] [c00f3e48] handle_irq_event+0x78/0xd0
[e5ee9f60] [c00fcfec] handle_fasteoi_irq+0x19c/0x370
[e5ee9fa0] [c00f1d84] generic_handle_irq+0x54/0x80
[e5ee9fc0] [c0006b54] __do_irq+0x64/0x200
[e5ee9ff0] [c0007958] __do_IRQ+0xe8/0x1c0
[c812dd50] [e3eaab20] 0xe3eaab20
[c812dd90] [c0007a4c] do_IRQ+0x1c/0x30
[c812dda0] [c0000c04] ExternalInput+0x144/0x160
--- interrupt: 500 at arch_cpu_idle+0x34/0x60
NIP: c000b684 LR: c000b684 CTR: c0019688
REGS: c812ddb0 TRAP: 0500 Tainted: G B (5.16.0-rc8)
MSR: 00029002 <CE,EE,ME> CR: 22000488 XER: 20000000
GPR00: c10ef7fc c812de90 c80ff200 c2394718 00000001 00000001 c10e3f90 00000003
GPR08: 00000000 c0019688 c2394718 fc7d625b 22000484 00000000 21e17000 c208228c
GPR16: e3e99284 00000000 ffffffff c2390000 c001bac0 c2082288 c812df60 c001ba60
GPR24: c23949c0 00000018 00080000 00000004 c80ff200 00000002 c2348ee4 c2394718
NIP [c000b684] arch_cpu_idle+0x34/0x60
LR [c000b684] arch_cpu_idle+0x34/0x60
--- interrupt: 500
[c812de90] [c10e3f90] rcu_eqs_enter.isra.60+0xc0/0x110 (unreliable)
[c812deb0] [c10ef7fc] default_idle_call+0xbc/0x230
[c812dee0] [c00af0e8] do_idle+0x1c8/0x200
[c812df10] [c00af3c0] cpu_startup_entry+0x20/0x30
[c812df20] [c001e010] start_secondary+0x5d0/0xba0
[c812dff0] [c00028a0] __secondary_start+0x90/0xdc
This happened because we would overrun the i2c->msgs array on the final
interrupt for the I2C STOP. This didn't happen if the last message was a
read because there is no interrupt in that case. Ensure that we only
access the current message if we are not processing a I2C STOP
condition.
Fixes: 1538d82f4647 ("i2c: mpc: Interrupt driven transfer")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a19f75de73c220b4496d2aefb7a605dd032f7c01 upstream.
This largely reverts commit 5a7b95fb993ec399c8a685552aa6a8fc995c40bd. It
breaks suspend with AMD GPUs, and we couldn't incrementally fix it. So,
let's remove the code and go back to the drawing board. We keep the
header extension to not break drivers already populating the regulator.
We expect to re-add the code handling it soon.
Fixes: 5a7b95fb993e ("i2c: core: support bus regulator controlling in adapter")
Reported-by: "Tareque Md.Hanif" <tarequemd.hanif@yahoo.com>
Link: https://lore.kernel.org/r/1295184560.182511.1639075777725@mail.yahoo.com
Reported-by: Konstantin Kharlamov <hi-angel@yandex.ru>
Link: https://lore.kernel.org/r/7143a7147978f4104171072d9f5225d2ce355ec1.camel@yandex.ru
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1850
Tested-by: "Tareque Md.Hanif" <tarequemd.hanif@yahoo.com>
Tested-by: Konstantin Kharlamov <hi-angel@yandex.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: <stable@vger.kernel.org> # 5.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bb436283e25aaf1533ce061605d23a9564447bdf ]
Wrong user data may cause warning in i2c_transfer(), ex: zero msgs.
Userspace should not be able to trigger warnings, so this patch adds
validation checks for user data in compact ioctl to prevent reported
warnings
Reported-and-tested-by: syzbot+e417648b303855b91d8a@syzkaller.appspotmail.com
Fixes: 7d5cb45655f2 ("i2c compat ioctls: move to ->compat_ioctl()")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 02fe0fbd8a21e183687925c3a266ae27dda9840f ]
In a typical read transfer, start completion flag is being set after
read finishes (notice ipd bit 4 being set):
trasnfer poll=0
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 33
This causes I2C transfer being aborted in polled mode from a stop completion
handler:
trasnfer poll=1
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 0
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 13
i2c stop
rk3x-i2c fdd40000.i2c: unexpected irq in STOP: 0x10
Clearing the START flag after read fixes the issue without any obvious
side effects.
This issue was dicovered on RK3566 when adding support for powering
off the RK817 PMIC.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b503de239f62eca898cfb7e820d9a35499137d22 ]
The driver currently assumes that the notify callback is only received
when the device is done with all the queued buffers.
However, this is not true, since the notify callback could be called
without any of the queued buffers being completed (for example, with
virtio-pci and shared interrupts) or with only some of the buffers being
completed (since the driver makes them available to the device in
multiple separate virtqueue_add_sgs() calls).
This can lead to incorrect data on the I2C bus or memory corruption in
the guest if the device operates on buffers which are have been freed by
the driver. (The WARN_ON in the driver is also triggered.)
BUG kmalloc-128 (Tainted: G W ): Poison overwritten
First byte 0x0 instead of 0x6b
Allocated in i2cdev_ioctl_rdwr+0x9d/0x1de age=243 cpu=0 pid=28
memdup_user+0x2e/0xbd
i2cdev_ioctl_rdwr+0x9d/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Freed in i2cdev_ioctl_rdwr+0x1bb/0x1de age=68 cpu=0 pid=28
kfree+0x1bd/0x1cc
i2cdev_ioctl_rdwr+0x1bb/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Fix this by calling virtio_get_buf() from the notify handler like other
virtio drivers and by actually waiting for all the buffers to be
completed.
Fixes: 3cfc88380413d20f ("i2c: virtio: add a virtio i2c frontend driver")
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
The hold_lock mutex is uninitialized when used, causing the warning:
[ 2.273892] WARNING: CPU: 0 PID: 1 at kernel/locking/mutex.c:575 __mutex_lock+0x8f8/0xb5c
[ 2.283107] DEBUG_LOCKS_WARN_ON(lock->magic != lock)
Initialize the hold_lock mutex before using it.
Also, move INIT_DELAYED_WORK() closer to other init functions to improve
readability.
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Change-Id: I26dda2451f8d27e947866d627f1909c9654f20aa
|
|
commit a74c313aca266fab0d1d1a72becbb8b7b5286b6e upstream.
Maxime points out that the polling code in mpc_i2c_isr should use the
_atomic API because it is called in an irq context and that the
behaviour of the MCF bit is that it is 1 when the byte transfer is
complete. All of this means the original code was effectively a
udelay(100).
Fix this by using readb_poll_timeout_atomic() and removing the negation
of the break condition.
Fixes: 4a8ac5e45cda ("i2c: mpc: Poll for MCF")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b12764695c3fcade145890b67f82f8b139174cc7 upstream.
CBUS transfers have always been atomic, but after commit 63b96983a5dd
("i2c: core: introduce callbacks for atomic transfers") we started to see
warnings during e.g. poweroff as the atomic callback is not explicitly set.
Fix that.
Fixes the following WARNING seen during Nokia N810 power down:
[ 786.570617] reboot: Power down
[ 786.573913] ------------[ cut here ]------------
[ 786.578826] WARNING: CPU: 0 PID: 672 at drivers/i2c/i2c-core.h:40 i2c_smbus_xfer+0x100/0x110
[ 786.587799] No atomic I2C transfer handler for 'i2c-2'
Fixes: 63b96983a5dd ("i2c: core: introduce callbacks for atomic transfers")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 31b90a95ccbbb4b628578ac17e3b3cc8eeacfe31 upstream.
In case of receiving a NACK, the dma transfer should be stopped
to avoid feeding data into the FIFO.
Also ensure to properly return the proper error code and avoid
waiting for the end of the dma completion in case of
error happening during the transmission.
Fixes: 7ecc8cfde553 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b933d1faf8fa30d16171bcff404e39c41b2a7c84 upstream.
When getting an access timeout, ensure that the bus is in a proper
state prior to returning the error.
Fixes: aeb068c57214 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c21d02ca469574d2082379db52d1a27b99eed0c upstream.
While handling an error during transfer (ex: NACK), it could
happen that the driver has already written data into TXDR
before the transfer get stopped.
This commit add TXDR Flush after end of transfer in case of error to
avoid sending a wrong data on any other slave upon next transfer.
Fixes: aeb068c57214 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 84e1d0bf1d7121759622dabf8fbef4c99ad597c5 ]
If a timeout is hit, it can result is incorrect data on the I2C bus
and/or memory corruptions in the guest since the device can still be
operating on the buffers it was given while the guest has freed them.
Here is, for example, the start of a slub_debug splat which was
triggered on the next transfer after one transfer was forced to timeout
by setting a breakpoint in the backend (rust-vmm/vhost-device):
BUG kmalloc-1k (Not tainted): Poison overwritten
First byte 0x1 instead of 0x6b
Allocated in virtio_i2c_xfer+0x65/0x35c age=350 cpu=0 pid=29
__kmalloc+0xc2/0x1c9
virtio_i2c_xfer+0x65/0x35c
__i2c_transfer+0x429/0x57d
i2c_transfer+0x115/0x134
i2cdev_ioctl_rdwr+0x16a/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Freed in virtio_i2c_xfer+0x32e/0x35c age=244 cpu=0 pid=29
kfree+0x1bd/0x1cc
virtio_i2c_xfer+0x32e/0x35c
__i2c_transfer+0x429/0x57d
i2c_transfer+0x115/0x134
i2cdev_ioctl_rdwr+0x16a/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
There is no simple fix for this (the driver would have to always create
bounce buffers and hold on to them until the device eventually returns
the buffers), so just disable the timeout support for now.
Fixes: 3cfc88380413d20f ("i2c: virtio: add a virtio i2c frontend driver")
Acked-by: Jie Deng <jie.deng@intel.com>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7f98960c046ee1136e7096aee168eda03aef8a5d ]
A successful 'clk_prepare()' call should be balanced by a corresponding
'clk_unprepare()' call in the error handling path of the probe, as already
done in the remove function.
More specifically, 'clk_prepare_enable()' is used, but 'clk_disable()' is
also already called. So just the unprepare step has still to be done.
Update the error handling path accordingly.
Fixes: 75d31c2372e4 ("i2c: xlr: add support for Sigma Designs controller variant")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b8228aea5a19d5111a7bf44f7de6749d1f5d487a ]
The reason for the modification here is that the previous
offset information is incorrect, OFFSET_DEBUGSTAT = 0xE4 is
the correct value.
Fixes: 25708278f810 ("i2c: mediatek: Add i2c support for MediaTek MT8183")
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7d6b61c394a42b8385858bb9e306d48a0112823c ]
As pointed out by Andy in [0] using a local mutex here isn't strictly
wrong but not sufficient. We should hold the PCI rescan lock for P2SB
operations.
[0] https://www.spinics.net/lists/linux-i2c/msg52717.html
Fixes: 1a987c69ce2c ("i2c: i801: make p2sb_spinlock a mutex")
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
These two exceptional cases were rarely observed in a slave device
reset or in a peer master reset conditions.
1. aspeed-i2c-bus 1e78a480.i2c-bus: irq handled != irq. expected 0x00000030, but was 0x00000020
when master goes from ASPEED_I2C_MASTER_STOP to
ASPEED_I2C_MASTER_INACTIVE state due to an
ASPEED_I2CD_INTR_ABNORMAL event. In this case,
ASPEED_I2CD_INTR_NORMAL_STOP should be simply ignored without
printing out the error message.
2. aspeed-i2c-bus 1e78a480.i2c-bus: irq handled != irq. expected 0x00000010, but was 0x00000000
when master already went to ASPEED_I2C_MASTER_INACTIVE. H/W sends
one additional ASPEED_I2CD_INTR_NORMAL_STOP event but it's a
garbage because driver is already in inactive state so filter it
off from the error message printing out.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@intel.com>
Change-Id: I94794a9612a7e8db445591e490bad6adae0faacf
|
|
Initial value of I2CD18 is undefined according to the datasheet
so this commit adds the I2CD18 register clearing code into bus
initialization function to prevent any unexpected slave match
events.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
|
|
When an arbitration loss happens in a multi-master bus, driver
drops the packet induce I2C subsystem to retry the transaction
by returning -EAGAIN. During this handling, tx_ack comes along
sometimes and it causes this this garbage printing
out:
aspeed-i2c-bus 1e78a400.i2c-bus: irq handled != irq. expected 0x00000009, but was 0x00000008
To fix this issue, this commit adds the tx_ack flag clearing into
the arbitration loss handling logic.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@intel.com>
|
|
AST2600 makes a garbage interrupt which is decribed as 'reserved'
in datasheet so filter them out.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@intel.com>
|
|
Since we enabled I2C busses in u-boot, we need to disable the I2C
bus and clear all garbage interrupts when kernel probes the bus.
This commit refines the initialization flow by adding a bus reset
at the beginning of probe function and by moving bus init function
after interrupt handling setup.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@intel.com>
|
|
If a peer master sends messages too quickly before it processes
previous slave DMA data handling, this indicator will be set. It's
just a indicator and driver can't recover this case so just ignore
it.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@intel.com>
|
|
This commit adds I2C H/W timeout support.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@intel.com>
|
|
This commit adds general call support into Aspeed I2C driver.
This is downstream only customization so it should not go into
upstream.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@intel.com>
|
|
This commit adds DMA mode transfer support.
Only AST2500 supports DMA mode under some limitations:
I2C is sharing the DMA H/W with UHCI host controller and MCTP
controller. Since those controllers operate with DMA mode only, I2C
has to use buffer mode or byte mode instead if one of those
controllers is enabled. Also make sure that if SD/eMMC or Port80
snoop uses DMA mode instead of PIO or FIFO respectively, I2C can't
use DMA mode.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@intel.com>
|
|
Byte mode currently this driver uses makes lots of interrupt call
which isn't good for performance and it makes the driver very
timing sensitive. To improve performance of the driver, this commit
adds buffer mode transfer support which uses I2C SRAM buffer
instead of using a single byte buffer.
AST2400:
It has 2 KBytes (256 Bytes x 8 pages) of I2C SRAM buffer pool from
0x1e78a800 to 0x1e78afff that can be used for all busses with
buffer pool manipulation. To simplify implementation for supporting
both AST2400 and AST2500, it assigns each 128 Bytes per bus without
using buffer pool manipulation so total 1792 Bytes of I2C SRAM
buffer will be used.
AST2500:
It has 16 Bytes of individual I2C SRAM buffer per each bus and its
range is from 0x1e78a200 to 0x1e78a2df, so it doesn't have 'buffer
page selection' bit field in the Function control register, and
neither 'base address pointer' bit field in the Pool buffer control
register it has. To simplify implementation for supporting both
AST2400 and AST2500, it writes zeros on those register bit fields
but it's okay because it does nothing in AST2500.
It provides buffer based master and slave data transfer.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@intel.com>
|
|
BMC uses I2C bus 7 as a PMBus channel to communicate with PSUs,
also ME uses this bus as SMLink to control PSUs so this bus is
managed by multi-masters. In this use case, some arbitration errors
are expected so we need to add retry logic. And PMBus subsystem
uses I2C bus in kernel internally so retry logic should be
supported in kernel level.
To support the use case, this commit adds 'bus-timeout-ms' and
'#retries' device tree properties to set the bus specific
parameters at kernel boot time without using any additional ioctls
from user space.
This patch would not be accepted by I2C maintainer in linux
upstream because he doesn't like adding these legacy properties
into device tree, so keep it only in downstream.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@intel.com>
|
|
This commit adds mux hold/unhold message types to support extended
mux control for IPMB and MCTP devices. A hold or an unhold message
can be added at the end of I2C message stream wrapped by
repeated-start, also can be used as a single message independantly.
This mux hold/unhold message will be delivered throughout all mux
levels in the path. Means that if it goes to multi-level mux path,
all muxes will be held/unheld by this message.
1. Hold message
struct i2c_msg msg;
uint16_t timeout = 5000; // timeout in ms. 5 secs in this example.
msg.addr = 0x0; // any value can be used. addr will be ignored in this packet.
msg.flags = I2C_M_HOLD; // set this flag to indicate it's a hold message.
msg.len = sizeof(uint16_t); // timeout value will be delivered using two bytes buffer.
msg.buf = (uint8_t *)&timeout; // set timeout value.
2. Unhold message
struct i2c_msg msg;
uint16_t timeout = 0; // set 0 for an unhold message.
msg.addr = 0x0; // any value can be used. addr will be ignored in this packet.
msg.flags = I2C_M_HOLD; // set this flag to indicate it's an unhold message.
msg.len = sizeof(uint16_t); // timeout value will be delivered using two bytes buffer.
msg.buf = (uint8_t *)&timeout; // set timeout value.
This unhold message can be delivered to a mux adapter even when
a bus is locked so that any holding state can be unheld
immediately by invoking this unhold message.
This patch would not be welcomed from upstream so it should be kept
in downstream only.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@intel.com>
|
|
This commit enables dump debug of master and slave I2C drivers.
This is only for downstream debug purpose so it shouldn't go to
the upstream.
Usage (in case of bus 5 for an example):
echo 5 > /sys/module/i2c_aspeed/parameters/dump_debug_bus_id
echo 1 > /sys/module/i2c_aspeed/parameters/dump_debug
echo 5 > /sys/module/i2c_slave_mqueue/parameters/dump_debug_bus_id
echo 1 > /sys/module/i2c_slave_mqueue/parameters/dump_debug
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@intel.com>
|
|
Some protocols over I2C are designed for bi-directional transferring
messages by using I2C Master Write protocol. Like the MCTP (Management
Component Transport Protocol) and IPMB (Intelligent Platform Management
Bus), they both require that the userspace can receive messages from
I2C dirvers under slave mode.
This new slave mqueue backend is used to receive and queue messages, it
will exposes these messages to userspace by sysfs bin file.
Signed-off-by: Haiyue Wang <haiyue.wang@linux.intel.com>
|
|
Change setting for 400KHz frequency support by more accurate value.
Fixes: 66b0c2846ba8 ("i2c: mlxcpld: Add support for I2C bus frequency setting")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Value for getting frequency capability wrongly has been taken from
register offset instead of register value.
Fixes: 66b0c2846ba8 ("i2c: mlxcpld: Add support for I2C bus frequency setting")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
In the commit be5ce0e97cc7 ("i2c: mediatek: Add i2c ac-timing adjust
support"), we miss setting OFFSET_EXT_CONF register if
i2c->dev_comp->timing_adjust is false, now add it back.
Fixes: be5ce0e97cc7 ("i2c: mediatek: Add i2c ac-timing adjust support")
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
acpi_i2c_find_adapter_by_handle() calls bus_find_device() which takes a
reference on the adapter which is never released which will result in a
reference count leak and render the adapter unremovable. Make sure to
put the adapter after creating the client in the same manner that we do
for OF.
Fixes: 525e6fabeae2 ("i2c / ACPI: add support for ACPI reconfigure notifications")
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: fixed title]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
"Highlights:
- Move all the Intel drivers into their own subdir(s) (mostly Kate's
work)
- New meraki-mx100 platform driver
- Asus WMI driver enhancements, including support for
/sys/firmware/acpi/platform_profile
- New BIOS SAR driver for Intel M.2 WWAM modems
- Alder Lake support for the Intel PMC driver
- A whole bunch of cleanups + fixes all over the place"
* tag 'platform-drivers-x86-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (65 commits)
platform/x86: dell-smbios-wmi: Add missing kfree in error-exit from run_smbios_call
platform/x86: dell-smbios-wmi: Avoid false-positive memcpy() warning
platform/x86: ISST: use semi-colons instead of commas
platform/x86: asus-wmi: Fix "unsigned 'retval' is never less than zero" smatch warning
platform/x86: asus-wmi: Delete impossible condition
platform/x86: hp_accel: Convert to be a platform driver
platform/x86: hp_accel: Remove _INI method call
platform/mellanox: mlxbf-pmc: fix kernel-doc notation
platform/x86/intel: pmc/core: Add GBE Package C10 fix for Alder Lake PCH
platform/x86/intel: pmc/core: Add Alder Lake low power mode support for pmc core
platform/x86/intel: pmc/core: Add Latency Tolerance Reporting (LTR) support to Alder Lake
platform/x86/intel: pmc/core: Add Alderlake support to pmc core driver
platform/x86: intel-wmi-thunderbolt: Move to intel sub-directory
platform/x86: intel-wmi-sbl-fw-update: Move to intel sub-directory
platform/x86: intel-vbtn: Move to intel sub-directory
platform/x86: intel_oaktrail: Move to intel sub-directory
platform/x86: intel_int0002_vgpio: Move to intel sub-directory
platform/x86: intel-hid: Move to intel sub-directory
platform/x86: intel_atomisp2: Move to intel sub-directory
platform/x86: intel_speed_select_if: Move to intel sub-directory
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did
the following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs users at
once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue"
* tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (33 commits)
MAINTAINERS: Add dri-devel for component.[hc]
driver core: platform: Remove platform_device_add_properties()
ARM: tegra: paz00: Handle device properties with software node API
bitmap: extend comment to bitmap_print_bitmask/list_to_buf
drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI
topology: use bin_attribute to break the size limitation of cpumap ABI
lib: test_bitmap: add bitmap_print_bitmask/list_to_buf test cases
cpumask: introduce cpumap_print_list/bitmask_to_buf to support large bitmask and list
sysfs: Rename struct bin_attribute member to f_mapping
sysfs: Invoke iomem_get_mapping() from the sysfs open callback
debugfs: Return error during {full/open}_proxy_open() on rmmod
zorro: Drop useless (and hardly used) .driver member in struct zorro_dev
zorro: Simplify remove callback
sh: superhyway: Simplify check in remove callback
nubus: Simplify check in remove callback
nubus: Make struct nubus_driver::remove return void
kernfs: dont call d_splice_alias() under kernfs node lock
kernfs: use i_lock to protect concurrent inode updates
kernfs: switch kernfs to use an rwsem
kernfs: use VFS negative dentry caching
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has a smaller pull reuest this time:
- new driver for I2C virtio
- removal of PMC SMP driver because platform is already gone
- IRQ probing and DMAENGINE API cleanups
- add SI metric prefix definitions to units.h
- beginning of i801 refactorization
- a few driver improvements"
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (28 commits)
i2c: cadence: Implement save restore
i2c: xlp9xx: fix main IRQ check
i2c: mt65xx: fix IRQ check
i2c: virtio: add a virtio i2c frontend driver
i2c: hix5hd2: fix IRQ check
i2c: s3c2410: fix IRQ check
i2c: iop3xx: fix deferred probing
i2c: synquacer: fix deferred probing
i2c: sun6i-pw2i: Prefer strscpy over strlcpy
i2c: remove dead PMC MSP TWI/SMBus/I2C driver
i2c: dev: Use sysfs_emit() in "show" functions
i2c: dev: Define pr_fmt() and drop duplication substrings
i2c: designware: Fix indentation in the header
i2c: designware: Use DIV_ROUND_CLOSEST() macro
units: Add SI metric prefix definitions
i2c: at91: mark PM ops as __maybe unused
i2c: sh_mobile: : use proper DMAENGINE API for termination
i2c: qup: : use proper DMAENGINE API for termination
i2c: mxs: : use proper DMAENGINE API for termination
i2c: imx: : use proper DMAENGINE API for termination
...
|
|
The zynqmp platform now supports chip-off so the registers can
lose context.
Implement save restore for i2c module.
Since we have only a couple of registers
an unconditional restore is done.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Iff platform_get_irq() returns 0 for the main IRQ, the driver's probe()
method will return 0 early (as if the method's call was successful).
Let's consider IRQ0 valid for simplicity -- devm_request_irq() can always
override that decision...
Fixes: 2bbd681ba2b ("i2c: xlp9xx: Driver for Netlogic XLP9XX/5XX I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: ce38815d39ea ("I2C: mediatek: Add driver for MediaTek I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add an I2C bus driver for virtio para-virtualization.
The controller can be emulated by the backend driver in
any device model software by following the virtio protocol.
The device specification can be found on
https://lists.oasis-open.org/archives/virtio-comment/202101/msg00008.html.
By following the specification, people may implement different
backend drivers to emulate different controllers according to
their needs.
Co-developed-by: Conghui Chen <conghui.chen@intel.com>
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Signed-off-by: Jie Deng <jie.deng@intel.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: 15ef27756b23 ("i2c: hix5hd2: add i2c controller driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: e0d1ec97853f ("i2c-s3c2410: Change IRQ to be plain integer.")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
When adding the code to handle platform_get_irq*() errors in the commit
489447380a29 ("handle errors returned by platform_get_irq*()"), the
actual error code was enforced to be -ENXIO in the driver for some
strange reason. This didn't matter much until the deferred probing was
introduced -- which requires an actual error code to be propagated
upstream from the failure site.
While fixing this, also stop overriding the errors from request_irq() to
-EIO (done since the pre-git era).
Fixes: 489447380a29 ("[PATCH] handle errors returned by platform_get_irq*()")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The driver overrides the error codes returned by platform_get_irq() to
-ENODEV, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Fixes: 0d676a6c4390 ("i2c: add support for Socionext SynQuacer I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
