summaryrefslogtreecommitdiff
path: root/drivers/hwmon
AgeCommit message (Collapse)AuthorFilesLines
2008-10-20hwmon: applesmc: lighter wait mechanism, drastic improvementHenrik Rydberg1-10/+12
The read fail ratio is sensitive to the delay between the first byte written and the first byte read; apparently the sensors cannot be rushed. Increasing the minimum wait time, without changing the total wait time, improves the fail ratio from a 8% chance that any of the sensors fails in one read, down to 0.4%, on a Macbook Air. On a Macbook Pro 3,1, the effect is even more apparent. By reducing the number of status polls, the ratio is further improved to below 0.1%. Finally, increasing the total wait time brings the fail ratio down to virtually zero. Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Tested-by: Bob McElrath <bob@mcelrath.org> Cc: Nicolas Boichat <nicolas@boichat.ch> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20hwmon: applesmc: Add support for Macbook Pro 3Henrik Rydberg1-0/+9
Add temperature sensor support for Macbook Pro 3. Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Cc: Nicolas Boichat <nicolas@boichat.ch> Cc: Riki Oktarianto <rkoktarianto@gmail.com> Cc: Mark M. Hoffman <mhoffman@lightlink.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20hwmon: applesmc: Add support for Macbook Pro 4Henrik Rydberg1-0/+9
Adds temperature sensor support for the Macbook Pro 4. Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Cc: Nicolas Boichat <nicolas@boichat.ch> Cc: Riki Oktarianto <rkoktarianto@gmail.com> Cc: Mark M. Hoffman <mhoffman@lightlink.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20drivers/hwmon/applesmc.c: remove unneeded castsAndrew Morton1-8/+8
dmi_system_id.driver_data is already void*. Cc: Henrik Rydberg <rydberg@euromail.se> Cc: Nicolas Boichat <nicolas@boichat.ch> Cc: Riki Oktarianto <rkoktarianto@gmail.com> Cc: Mark M. Hoffman <mhoffman@lightlink.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20hwmon: applesmc: add support for Macbook AirHenrik Rydberg1-0/+9
This patch adds accelerometer, backlight and temperature sensor support for the Macbook Air. Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Cc: Nicolas Boichat <nicolas@boichat.ch> Cc: Riki Oktarianto <rkoktarianto@gmail.com> Cc: Mark M. Hoffman <mhoffman@lightlink.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20hwmon: applesmc: allow for variable ALV0 and ALV1 package lengthHenrik Rydberg1-5/+15
On some recent Macbooks, the package length for the light sensors ALV0 and ALV1 has changed from 6 to 10. This patch allows for a variable package length encompassing both variants. Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Cc: Nicolas Boichat <nicolas@boichat.ch> Cc: Riki Oktarianto <rkoktarianto@gmail.com> Cc: Mark M. Hoffman <mhoffman@lightlink.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20hwmon: applesmc: prolong status waitHenrik Rydberg1-2/+2
The time to wait for a status change while reading or writing to the SMC ports is a balance between read reliability and system performance. The current setting yields rougly three errors in a thousand when simultaneously reading three different temperature values on a Macbook Air. This patch increases the setting to a value yielding roughly one error in ten thousand, with no noticable system performance degradation. Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Cc: Nicolas Boichat <nicolas@boichat.ch> Cc: Riki Oktarianto <rkoktarianto@gmail.com> Cc: Mark M. Hoffman <mhoffman@lightlink.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20hwmon: applesmc: fix the 'wait status failed: c != 8' problemHenrik Rydberg1-8/+24
On many Macbooks since mid 2007, the Pro, C2D and Air models, applesmc fails to read some or all SMC ports. This problem has various effects, such as flooded logfiles, malfunctioning temperature sensors, accelerometers failing to initialize, and difficulties getting backlight functionality to work properly. The root of the problem seems to be the command protocol. The current code sends out a command byte, then repeatedly polls for an ack before continuing to send or recieve data. From experiments leading to this patch, it seems the command protocol never quite worked or changed so that one now sends a command byte, waits a little bit, polls for an ack, and if it fails, repeats the whole thing by sending the command byte again. This patch implements a send_command function according to the new interpretation of the protocol, and should work also for earlier models. Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Cc: Nicolas Boichat <nicolas@boichat.ch> Cc: Riki Oktarianto <rkoktarianto@gmail.com> Cc: Mark M. Hoffman <mhoffman@lightlink.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20hwmon: applesmc: specified number of bytes to read should match actualHenrik Rydberg1-1/+1
At one single place in the code, the specified number of bytes to read and the actual number of bytes read differ by one. This one-liner patch fixes that inconsistency. Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Cc: Nicolas Boichat <nicolas@boichat.ch> Cc: Riki Oktarianto <rkoktarianto@gmail.com> Cc: Mark M. Hoffman <mhoffman@lightlink.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20hwmon/pc87360 separate alarm files: add therm-min/max/crit-alarmsJim Cromie1-1/+57
Adds therm-min/max/crit-alarm callbacks, sensor-device-attribute declarations, and refs to those new decls in the macro used to initialize the therm_group (of sysfs files) The thermistors use voltage channels to measure; so they don't have a fault-alarm, but unlike the other voltages, they do have an overtemp, which we call crit (by convention). [akpm@linux-foundation.org: cleanup] Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20hwmon/pc87360 separate alarm files: add dev_dbg helpJim Cromie1-4/+12
temp and vin status register values may be set by chip specifications, set again by bios, or by this previously loaded driver. Debug output nicely displays modprobe init=\d actions. Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20hwmon/pc87360 separate alarm files: define LDNI_MAX constJim Cromie1-2/+3
Driver handles 3 logical devices in fixed length array. Give this a define-d constant. Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20hwmon/pc87360 separate alarm files: add temp-min/max/crit/fault-alarmsJim Cromie1-4/+80
Adds temp-min/max/crit/fault-alarm callbacks, sensor-device-attribute declarations, and refs to those new decls in the macro used to initialize the temp_group (of sysfs files) [akpm@linux-foundation.org: cleanups] Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20hwmon/pc87360 separate alarm files: add in-min/max-alarmsJim Cromie1-1/+51
Adds vin-min/max-alarm callbacks, sensor-device-attribute declarations, and refs to those new decls in the macro used to initialize the vin_group (of sysfs files) [akpm@linux-foundation.org: cleanups] Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20hwmon/pc87360 separate alarm files: define some constantsJim Cromie1-11/+22
Bring hwmon/pc87360 into agreement with Documentation/hwmon/sysfs-interface. Patchset adds separate limit alarms for voltages and temps, it also adds temp[123]_fault files. On my Soekris, temps 1,2 are unused/unconnected, so temp[123]_fault = 1,1,0 respectively. This agrees with /usr/bin/sensors, which has always shown them as OPEN. Temps 4,5,6 are thermistor based, and dont have a fault bit in their status register. This patch: 2 different kinds of constants added: - CHAN_ALM_* constants for (later) vin, temp alarm callbacks. - CHAN_* conversion constants, used in _init_device, partly for RW1C bits Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-17hwmon: (adm1026) Prevent log spammingJean Delvare1-4/+4
When debugging is enabled, the adm1026 driver currently logs the message "Setting VID from GPIO11-15" 108 times each time you run "sensors". Once should be enough. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Philip Pokorny <ppokorny@penguincomputing.com>
2008-10-17hwmon: (adm1026) Fix debug messagesJean Delvare1-5/+4
* Add missing new-line to one debug message. * Remove leading colon from 3 debug messages. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Philip Pokorny <ppokorny@penguincomputing.com>
2008-10-17hwmon: (adm1029) Use mask for fan_div valueCorentin Labbe1-2/+3
This is my patch for testing correct values of fan div in adm1029 and prevent a division by 0 for some (unlikely) register values. Signed-off-by: Corentin Labbe <corentin.labbe@geomatys.fr> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (ibmaem) Automatically load on IBM systems via DMIDarrick J. Wong1-0/+7
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (ibmpex) Automatically load on IBM systems via DMIDarrick J. Wong1-0/+6
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (w83781d) Use new style driver bindingWolfgang Grandegger1-175/+134
This patch modifies the w83781d driver to use new style driver binding. Substantial code modifications are required to deal with the new interface, especially legacy device detection. [JD: largely edited to make the patch smaller and to get the driver to work again on ISA devices.] Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (w83781d) Stop abusing struct i2c_client for ISA devicesJean Delvare1-37/+26
Upcoming changes to the I2C part of the w83781d driver will cause ISA devices to no longer have a struct i2c_client at hand. So, we must stop (ab)using it now. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Wolfgang Grandegger <wg@grandegger.com>
2008-10-17hwmon: (w83781d) Make ISA interface depend on CONFIG_ISAWolfgang Grandegger1-280/+393
Probing the ISA bus on systems without ISA bus may hang the system. This patch makes the ISA bus related code depend on the kernel configuration parameter CONFIG_ISA. It moves ISA bus related code into one #ifdef CONFIG_ISA ... #endif block and adds some helper function. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (w83781d) Detect alias chipsJean Delvare1-13/+66
The W83781D and W83782D can be accessed either on the I2C bus or the ISA bus. We must not access the same chip through both interfaces. So far we were relying on the user passing the correct ignore parameter to skip the registration of the I2C interface as suggested by sensors-detect, but this is fragile: the user may load the w83781d driver without running sensors-detect, and the i2c bus numbers are not stable across reboots and hardware changes. So, better detect alias chips in the driver directly, and skip any I2C chip which is obviously an alias of the ISA chip. This is done by comparing the value of 26 selected registers. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Wolfgang Grandegger <wg@grandegger.com>
2008-10-17hwmon: (w83781d) Refactor beep enable handlingJean Delvare1-37/+9
We can handle the beep enable bit as any other beep mask bit for slightly smaller code. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Wolfgang Grandegger <wg@grandegger.com>
2008-10-17hwmon: (w83791d) add support for thermal cruise modeMarc Hulsman1-0/+148
Add support to set target temperature and tolerance for thermal cruise mode. Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl> Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (w83791d) add pwm_enable supportMarc Hulsman1-0/+79
Add support for pwm_enable. Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl> Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (w83791d) add manual PWM supportMarc Hulsman1-1/+66
Add PWM manual control. Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl> Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (w83791d) fan 4/5 pins can also be used for gpioMarc Hulsman1-3/+27
Pins fan/pwm 4-5 can be in use as GPIO. If that is the case, do not create their sysfs-interface. Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl> Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (max1619) Use inline functions instead of macrosAndrew Morton1-5/+12
Macros evaluating their arguments more than once are evil. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (it87) Fix thermal sensor type valuesJean Delvare1-3/+8
The it87 driver doesn't follow the standard sensor type values as documented in Documentation/hwmon/sysfs-interface. It uses value 2 for thermistors instead of value 4. This causes "sensors" to tell the user that the chip is setup for a transistor while it is actually setup for a thermistor. Using value 4 for thermistors solves the problem. For compatibility reasons, we still accept value 2 but emit a warning message so that users update their configuration files. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Hans de Goede <hdegoede@redhat.com>
2008-10-17hwmon: (lm78) Convert to a new-style i2c driverJean Delvare1-105/+89
The new-style lm78 driver implements the optional detect() callback to cover the use cases of the legacy driver. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (lm78) Stop abusing struct i2c_client for ISA devicesJean Delvare1-22/+16
Upcoming changes to the I2C part of the lm78 driver will cause ISA devices to no longer have a struct i2c_client at hand. So, we must stop (ab)using it now. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (lm78) Prevent misdetection of Winbond chipsJean Delvare1-0/+6
The LM78 detection is relatively weak, and sometimes recent Winbond chips can be misdetected as an LM78. We have had repeated reports of this happening. We have an explicit check against this for the ISA access, do the same for I2C access now. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (lm78) Detect alias chipsJean Delvare1-13/+65
The LM78 and LM79 can be accessed either on the I2C bus or the ISA bus. We must not access the same chip through both interfaces. So far we were relying on the user passing the correct ignore parameter to skip the registration of the I2C interface as suggested by sensors-detect, but this is fragile: the user may load the lm78 driver without running sensors-detect, and the i2c bus numbers are not stable across reboots and hardware changes. So, better detect alias chips in the driver directly, and skip any I2C chip which is obviously an alias of the ISA chip. This is done by comparing the value of 26 selected registers. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (lm78) Fix I/O resource conflict with PNPJean Delvare1-5/+15
Only request I/O ports 0x295-0x296 instead of the full I/O address range. This solves a conflict with PNP resources on a few motherboards. Also request the I/O ports in two parts (4 low ports, 4 high ports) during device detection, otherwise the PNP resource make the request (and thus the detection) fail. This is the exact same fix that was applied to driver w83781d in March 2008 to address the same problem: http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=2961cb22ef02850d90e7a12c28a14d74e327df8d Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (lm85) Better label namesJean Delvare1-6/+6
Label names ERROR1 and ERROR3 aren't exactly explicit. Change them for better names that indicate what we are up to. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Herbert Poetzl <herbert@13thfloor.at>
2008-10-17hwmon: (lm85) Simplify RANGE_TO_REGJean Delvare1-11/+4
Function RANGE_TO_REG can easily be simplified. Credits go to Herbert Poetzl for indirectly suggesting this to me. I tested that the new implementation returns the same result as the original implementation for all input values. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Herbert Poetzl <herbert@13thfloor.at>
2008-10-17hwmon: (lm85) Convert to a new-style i2c driverJean Delvare1-57/+64
The new-style lm85 driver implements the optional detect() callback to cover the use cases of the legacy driver. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Herbert Poetzl <herbert@13thfloor.at>
2008-10-17hwmon: (lm85) Support different PWM frequency tablesJean Delvare1-6/+23
The Analog Devices and SMSC devices supported by the lm85 driver do not have the same PWM frequency table as the National Semiconductor devices. Add support for per-device frequency tables. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Herbert Poetzl <herbert@13thfloor.at>
2008-10-17hwmon: (lm85) Select the closest PWM frequencyJean Delvare1-3/+2
The LM85 and compatible chips only support 8 arbitrary PWM frequencies. The algorithm to pick one of them based on the user input is not optimum. Improve it to always pick the closest supported frequency. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Herbert Poetzl <herbert@13thfloor.at>
2008-10-17hwmon: (lm85) Implement the standard PWM frequency interfaceJean Delvare1-39/+38
Implement the standard PWM frequency interface: pwm[1-*]_freq in units of 1 Hz, instead of the non-standard pwm[1-*]_auto_pwm_freq in units of 0.1 Hz. The old naming was not only non-standard, it was also confusing, because it suggested that the frequency value only applied in automatic fan speed mode, which isn't true. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Herbert Poetzl <herbert@13thfloor.at>
2008-10-17hwmon: (lm85) Rework the device detectionJean Delvare1-73/+50
Rework the device detection to make it clearer and faster in the general case (when a known device is found.) Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Herbert Poetzl <herbert@13thfloor.at>
2008-10-17hwmon: (ams) Simplify IRQ handling routineDmitry Torokhov1-25/+17
Simplify the IRQ handling routine of ams driver. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (ams) Fix locking issuesDmitry Torokhov4-65/+56
Use a separate mutex to serialize input device creation/removal, otheriwse we deadlock if we try to remove input device while it is being polled. Also do not take ams_info.lock when it is not needed. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (ams) Fix permissions on 'joystick' module parameterDmitry Torokhov1-2/+2
We should not allow writes to the 'joystick' module parameters since writing there will not trigger creation of the input device. Disable writes since we provide alternative way of enabling input device via AMS device's sysfs attribute. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (ams) Convert to a new-style i2c driverJean Delvare2-41/+19
The legacy i2c binding model is phasing out, so the ams driver needs to be converted to a new-style i2c driver. Here is a naive approach of this conversion. Basically it is moving the i2c device creation from the ams driver to the i2c-powermac driver. This should work, but I suspect we could come up with something cleaner by declaring the i2c device as part of the platform setup. This could be done later by someone more familiar with openfirmware-based platforms than I am myself. One nice thing brought by this conversion is that the ams driver should be loaded automatically on systems where is is needed (at least when the I2C interface to the chip is used) providing coldplug-aware user-space environment. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Johannes Berg <johannes@sipsolutions.net> Cc: Stelian Pop <stelian@popies.net> Cc: Michael Hanselmann <linux-kernel@hansmi.ch> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2008-10-17hwmon: (lm87) Add support for configuration through platform_dataBen Hutchings1-6/+11
The lm87 driver normally assumes that firmware configured the chip correctly. Since this is not always the case, alllow platform code to set the channel register value via platform_data. All other configuration registers can be changed after driver initialisation. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (lm87) Restore original configuration register on removalBen Hutchings1-5/+7
This means that if we have to start the monitor when probed, we also stop it on removal. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17hwmon: (lm87) Fix masking of config register in lm87_init_client()Ben Hutchings1-4/+4
lm87_init_client() conditionally sets the Start bit and clears the INT#_Clear bit in the Config 1 register. The condition should be that either of these bits needs changing, but currently it checks the (self-clearing) Initialization bit instead of INT#_Clear. Fix the condition and also ensure we never set the Initialization bit. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
generated by cgit v1.2.3 (git 2.39.0) at 2024-11-23 10:08:45 +0300