| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"A single ARM Juno clocksource driver fix"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/arm_arch_timer: Fix arch_timer_mem_find_best_frame()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
|
|
arch_timer_mem_find_best_frame() looks through ARCH_TIMER_MEM_MAX_FRAMES
frames even after finding matches to ensure the best frame is chosen,
which means the variable frame will point to the last valid frame but
not necessarily the best frame.
On Juno, we get the following error as the wrong frame is returned as the
best frame from arch_timer_mem_find_best_frame():
arch_timer: Unable to map frame @ 0x0000000000000000
arch_timer: Frame missing phys irq.
Failed to initialize '/timer@2a810000': -22
Fix the issue by correctly returning the best frame from
arch_timer_mem_find_best_frame().
Fixes: c389d701dfb7 ("clocksource: arm_arch_timer: split MMIO timer probing.")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1494246747-17267-1-git-send-email-sudeep.holla@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"The timer departement delivers:
- more year 2038 rework
- a massive rework of the arm achitected timer
- preparatory patches to allow NTP correction of clock event devices
to avoid early expiry
- the usual pile of fixes and enhancements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (91 commits)
timer/sysclt: Restrict timer migration sysctl values to 0 and 1
arm64/arch_timer: Mark errata handlers as __maybe_unused
Clocksource/mips-gic: Remove redundant non devicetree init
MIPS/Malta: Probe gic-timer via devicetree
clocksource: Use GENMASK_ULL in definition of CLOCKSOURCE_MASK
acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver
clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
acpi/arm64: Add memory-mapped timer support in GTDT driver
clocksource: arm_arch_timer: simplify ACPI support code.
acpi/arm64: Add GTDT table parse driver
clocksource: arm_arch_timer: split MMIO timer probing.
clocksource: arm_arch_timer: add structs to describe MMIO timer
clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT init call
clocksource: arm_arch_timer: refactor arch_timer_needs_probing
clocksource: arm_arch_timer: split dt-only rate handling
x86/uv/time: Set ->min_delta_ticks and ->max_delta_ticks
unicore32/time: Set ->min_delta_ticks and ->max_delta_ticks
um/time: Set ->min_delta_ticks and ->max_delta_ticks
tile/time: Set ->min_delta_ticks and ->max_delta_ticks
score/time: Set ->min_delta_ticks and ->max_delta_ticks
...
|
|
In some rare randconfig builds, we end up with two functions being entirely
unused:
drivers/clocksource/arm_arch_timer.c:342:12: error: 'erratum_set_next_event_tval_phys' defined but not used [-Werror=unused-function]
static int erratum_set_next_event_tval_phys(unsigned long evt,
drivers/clocksource/arm_arch_timer.c:335:12: error: 'erratum_set_next_event_tval_virt' defined but not used [-Werror=unused-function]
static int erratum_set_next_event_tval_virt(unsigned long evt,
We could add an #ifdef around them, but we would already have to check for
several symbols there and there is a chance this would get more complicated
over time, so marking them as __maybe_unused is the simplest way to avoid the
harmless warnings.
Fixes: 01d3e3ff2608 ("arm64: arch_timer: Rework the set_next_event workarounds")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Link: http://lkml.kernel.org/r/20170419173737.3846098-1-arnd@arndb.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Malta was the only platform probing this driver from platform code
without using device tree. With that code removed, gic_clocksource_init
is redundant so remove it.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/1492604806-23420-2-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/clocksource/.
[Note: With regard to cs5535-clockevt.c, Thomas Gleixner asked whether the
timer_irq parameter is required for the driver to work on anything other than
arbitrary hardware which has it mapped to 0. Jens Rottmann replied that the
parameter defaults to 0, which means:
1. autodetect (=keep IRQ BIOS has set up)
2. if that fails use CONFIG_CS5535_MFGPT_DEFAULT_IRQ
(see drivers/misc/cs5535-mfgpt.c: cs5535_mfgpt_set_irq())
Jens further noted that there may not be any systems that have CS5535/36
devices that support EFI and secure boot.]
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Daniel Lezcano <daniel.lezcano@linaro.org>
cc: Thomas Gleixner <tglx@linutronix.de>
cc: Jens Rottmann <Jens.Rottmann@ADLINKtech.com>
cc: linux-kernel@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mark/linux into timers/core
Pull arch timer GTDT support from Mark Rutland
- arch_timer cleanups and refactoring
- new common GTDT parser
- GTDT-based MMIO arch_timer support
- GTDT-based SBSA watchdog support
Fix up a trivial pr_err() conflict.
|
|
The patch add memory-mapped timer register support by using the
information provided by the new GTDT driver of ACPI.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
[Mark: verify CNTFRQ, only register the first frame]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
|
|
The patch update arm_arch_timer driver to use the function
provided by the new GTDT driver of ACPI.
By this way, arm_arch_timer.c can be simplified, and separate
all the ACPI GTDT knowledge from this timer driver.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
|
|
Currently the code to probe MMIO architected timers mixes DT parsing with
actual poking of hardware. This makes the code harder than necessary to
understand, and makes it difficult to add support for probing via ACPI.
This patch splits the DT parsing from HW probing. The DT parsing now
lives in arch_timer_mem_of_init(), which fills in an arch_timer_mem
structure that it hands to probing functions that can be reused for ACPI
support.
Since the rate detection logic will be slight different when using ACPI,
the probing is performed as a number of steps. This results in more code
for the moment, and some arguably redundant work, but simplifies matters
considerably when ACPI support is added.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
[Mark: refactor the probing split]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
|
|
To cleanly split code paths specific to ACPI or DT at a higher level,
this patch removes arch_timer_init(), folding the relevant
parts of its logic into existing callers.
This pathes the way for further rework, and saves a few lines.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
|
|
When booting with DT, it's possible for timer nodes to be probed in any
order. Some common initialisation needs to occur after all nodes have
been probed, and arch_timer_common_init() has code to detect when this
has happened.
This logic is DT-specific, and it would be best to factor it out of the
common code that will be shared with ACPI.
This patch folds this into the existing arch_timer_needs_probing(),
which is renamed to arch_timer_needs_of_probing(), and no longer takes
any arguments. This is only called when using DT, and not when using
ACPI, which will have a deterministic probe order.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
|
|
For historical reasons, rate detection when probing via DT is somewhat
convoluted. We tried to package this up in arch_timer_detect_rate(), but
with the addition of ACPI worse, and gets in the way of stringent rate
checking when ACPI is used.
This patch makes arch_timer_detect_rate() specific to DT, ripping out
ACPI logic. In preparation for rework of the MMIO timer probing, the
reading of the relevant CNTFRQ register is factored out to callers. The
function is then renamed to arch_timer_of_configure_rate(), which better
represents its new place in the world.
Comments are added in the DT and ACPI probe paths to explain this.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
|
|
https://git.linaro.org/people/daniel.lezcano/linux into timers/core
Pull clockevents updates from Daniel Lezcano
- Provide a framework to handle errata gracefuly for arm_arch_timer (Mark
Zyngier)
- Clarify the DT properties for the rockchip timer and add the clocksource as
an alternative to the bogus architected timer (Alexander Kochetkov)
- Rename the Gemini timer to Faraday timer fttmr010 and provide a specific
initialization for Gemini (Linus Walleij)
- Add missing newlines in the error message in the timers (Rafał Miłecki)
- Read the clock once and implement the delay timer on Orion (Russell King)
|
|
In preparation for making the clockevents core NTP correction aware,
all clockevent device drivers must set ->min_delta_ticks and
->max_delta_ticks rather than ->min_delta_ns and ->max_delta_ns: a
clockevent device's rate is going to change dynamically and thus, the
ratio of ns to ticks ceases to stay invariant.
Make the timer-atlas7 clockevent driver initialize these fields properly.
This patch alone doesn't introduce any change in functionality as the
clockevents core still looks exclusively at the (untouched) ->min_delta_ns
and ->max_delta_ns. As soon as this has changed, a followup patch will
purge the initialization of ->min_delta_ns and ->max_delta_ns from this
driver.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Barry Song <baohua@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
In preparation for making the clockevents core NTP correction aware,
all clockevent device drivers must set ->min_delta_ticks and
->max_delta_ticks rather than ->min_delta_ns and ->max_delta_ns: a
clockevent device's rate is going to change dynamically and thus, the
ratio of ns to ticks ceases to stay invariant.
Make the sh_cmt clockevent driver initialize these fields properly.
This patch alone doesn't introduce any change in functionality as the
clockevents core still looks exclusively at the (untouched) ->min_delta_ns
and ->max_delta_ns. As soon as this has changed, a followup patch will
purge the initialization of ->min_delta_ns and ->max_delta_ns from this
driver.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
In preparation for making the clockevents core NTP correction aware,
all clockevent device drivers must set ->min_delta_ticks and
->max_delta_ticks rather than ->min_delta_ns and ->max_delta_ns: a
clockevent device's rate is going to change dynamically and thus, the
ratio of ns to ticks ceases to stay invariant.
Make the numachip clockevent driver initialize these fields properly.
This patch alone doesn't introduce any change in functionality as the
clockevents core still looks exclusively at the (untouched) ->min_delta_ns
and ->max_delta_ns. As soon as this has changed, a followup patch will
purge the initialization of ->min_delta_ns and ->max_delta_ns from this
driver.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
In preparation for making the clockevents core NTP correction aware,
all clockevent device drivers must set ->min_delta_ticks and
->max_delta_ticks rather than ->min_delta_ns and ->max_delta_ns: a
clockevent device's rate is going to change dynamically and thus, the
ratio of ns to ticks ceases to stay invariant.
Make the metag_generic clockevent driver initialize these fields properly.
This patch alone doesn't introduce any change in functionality as the
clockevents core still looks exclusively at the (untouched) ->min_delta_ns
and ->max_delta_ns. As soon as this has changed, a followup patch will
purge the initialization of ->min_delta_ns and ->max_delta_ns from this
driver.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
In preparation for making the clockevents core NTP correction aware,
all clockevent device drivers must set ->min_delta_ticks and
->max_delta_ticks rather than ->min_delta_ns and ->max_delta_ns: a
clockevent device's rate is going to change dynamically and thus, the
ratio of ns to ticks ceases to stay invariant.
Make the dw_apb clockevent driver initialize these fields properly.
This patch alone doesn't introduce any change in functionality as the
clockevents core still looks exclusively at the (untouched) ->min_delta_ns
and ->max_delta_ns. As soon as this has changed, a followup patch will
purge the initialization of ->min_delta_ns and ->max_delta_ns from this
driver.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Currently, the arch timer driver uses ARCH_TIMER_PHYS_SECURE_PPI to mean
the driver will use the secure PPI *and* potentially also use the
non-secure PPI. This is somewhat confusing.
For arm64 it never makes sense to use the secure PPI, but we do anyway,
inheriting this behaviour from 32-bit arm. For ACPI, we may not even
have a valid secure PPI, so we need to be able to only request the
non-secure PPI.
To that end, this patch reworks the timer driver so that we can request
the non-secure PPI alone. The PPI selection is split out into a new
function, arch_timer_select_ppi(), and verification of the selected PPI
is shifted out to callers (as DT may select the PPI by other means and
must handle this anyway).
We now consistently use arch_timer_has_nonsecure_ppi() to determine
whether we must manage a non-secure PPI *in addition* to a secure PPI.
When we only have a non-secure PPI, this returns false.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
|
|
This patch add a new enum "arch_timer_spi_nr" and use it in the driver.
Just for code's readability, no functional change.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
|
|
To support the arm_arch_timer via ACPI we need to share defines and enums
between the driver and the ACPI parser code.
So we split out the relevant defines and enums into arm_arch_timer.h.
No functional change.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
|
|
In preparation for moving the PPI enum out into a header, rename the
enum and its constituent values these so they are namespaced w.r.t. the
arch timer. This will aid consistency and avoid potential name clashes
when this move occurs.
No functional change.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
|
|
In preparation for moving the type macros out into a header, rename
these so they are namespaced w.r.t. the arch timer. We'll apply the same
prefix to other definitions in subsequent patches. This will aid
consistency and avoid potential name clahses when this move occurs.
No functional change.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
|
|
Almost all string in the arm_arch_timer driver duplicate an common
prefix (though a few do not). For consistency, it would be better to use
pr_fmt(), and always use this prefix. At the same time, we may as well
clean up some whitespace issues in arch_timer_banner and
arch_timer_init.
No functional change.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into clockevents/4.12
arm64 arch timer workaround series, including the base patches
that will also go via the arm64 tree.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The plain Faraday FTTMR010 timer needs a clock to figure out its
tick rate, and the gemini reads it directly from the system
controller set-up. Split the init function and add two paths for
the two compatible-strings. We only support clocking using PCLK
because of lack of documentation on how EXTCLK works.
The Gemini still works like before, but we can also support a
generic, clock-based version.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
After some research it turns out that the "Gemini" timer is
actually a generic IP block from Faraday Technology named
FTTMR010, so as to not make things too confusing we need to
rename the driver and its symbols to make sense.
The implementation remains the same in this patch but we fix
the copy-paste error in the timer name "nomadik_mtu" as we're
at it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The clock supplying the arm-global-timer on the rk3188 is coming from the
the cpu clock itself and thus changes its rate everytime cpufreq adjusts
the cpu frequency making this timer unsuitable as a stable clocksource
and sched clock.
The rk3188, rk3288 and following socs share a separate timer block already
handled by the rockchip-timer driver. Therefore adapt this driver to also
be able to act as clocksource and sched clock on rk3188.
In order to test clocksource you can run following commands and check
how much time it take in real. On rk3188 it take about ~45 seconds.
cpufreq-set -f 1.6GHZ
date; sleep 60; date
In order to use the patch you need to declare two timers in the dts
file. The first timer will be initialized as clockevent provider
and the second one as clocksource. The clockevent must be from
alive subsystem as it used as backup for the local timers at sleep
time.
The patch does not break compatibility with older device tree files.
The older device tree files contain only one timer. The timer
will be initialized as clockevent, as expected.
rk3288 (and probably anything newer) is irrelevant to this patch,
as it has the arch timer interface. This patch may be useful
for Cortex-A9/A5 based parts.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Printing with pr_* functions requires adding line break manually.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Add an implementation for the ARM delay timer, which is used for
udelay(). This provides less CPU dependent and more accurate delays -
the CPU loop on Marvell Dove appears to calibrate to around 6% too
short.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Rather than reading the clock rate three times, read it once - we are
about to add a fourth usage.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
In order to deal with ACPI enabled platforms suffering from the
HISILICON_ERRATUM_161010101, let's add the required OEM data that
allow the workaround to be enabled.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: dann frazier <dann.frazier@canonical.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Just as we're able to identify a broken platform using some DT
information, let's enable a way to spot the offenders with ACPI.
The difference is that we can only match on some OEM info instead
of implementation-specific properties. So in order to avoid the
insane multiplication of errata structures, we allow an array
of OEM descriptions to be attached to an erratum structure.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: dann frazier <dann.frazier@canonical.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Cortex-A73 (all versions) counter read can return a wrong value
when the counter crosses a 32bit boundary.
The workaround involves performing the read twice, and to return
one or the other depending on whether a transition has taken place.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Userspace being allowed to use read CNTVCT_EL0 anytime (and not
only in the VDSO), we need to enable trapping whenever a cntvct
workaround is enabled on a given CPU.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
As we're about to allow per CPU cntkctl_el1 configuration, we cannot
rely on the register value to be common when performing power
management.
Let's turn saved_cntkctl into a per-cpu variable.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
In order to access clocksource_counter from the errata handling code,
move it (together with the related structures and functions) towards
the top of the file.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Instead of applying a CPU-specific workaround to all CPUs in the system,
allow it to only affect a subset of them (typical big-little case).
This is done by turning the erratum pointer into a per-CPU variable.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The way we work around errata affecting set_next_event is not very
nice, at it imposes this workaround on errata that do not need it.
Add new workaround hooks and let the existing workarounds use them.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Let's move the handling of workarounds affecting set_next_event
to the affected function, instead of overriding the pointers
as an afterthough. Yes, this is an extra indirection on the
erratum handling path, but the HW is busted anyway.
This will allow for some more flexibility later.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
As we're about to move things around, let's start with the low
level read/write functions. This allows us to use these functions
in the errata handling code without having to use forward declaration
of static functions.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Should we ever have a workaround for an erratum that is detected using
a capability and affecting a particular CPU, it'd be nice to have
a way to probe them directly.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
We're currently stuck with DT when it comes to handling errata, which
is pretty restrictive. In order to make things more flexible, let's
introduce an infrastructure that could support alternative discovery
methods. No change in functionality.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two small fixes for the new CLKEVT_OF infrastructure"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
vmlinux.lds: Add __clkevt_of_table to kernel
clockevents: Fix syntax error in clkevt-of macro
|
|
The patch fix syntax errors introduced by commit 0c8893c9095d
("clockevents: Add a clkevt-of mechanism like clksrc-of").
Fixes: 0c8893c9095d ("clockevents: Add a clkevt-of mechanism like clksrc-of")
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
With the upcoming NTP correction related rate adjustments to be implemented
in the clockevents core, the latter needs to get informed about every rate
change of a clockevent device made after its registration.
Currently, h8300_timer8 violates this requirement in that it registers its
clockevent device with the correct rate, but resets its ->mult and ->rate
values in timer8_clock_event_start(), called from its ->set_state_oneshot()
function.
It seems like
commit 4633f4cac85a ("clocksource/drivers/h8300: Cleanup startup and
remove module code."),
which introduced the rate initialization at registration, missed to remove
the manual setting of ->mult and ->shift from timer8_clock_event_start().
Purge the setting of ->mult, ->shift, ->min_delta_ns and ->max_delta_ns
from timer8_clock_event_start().
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
With the upcoming NTP correction related rate adjustments to be implemented
in the clockevents core, the latter needs to get informed about every rate
change of a clockevent device made after its registration.
Currently, em_sti violates this requirement in that it registers its
clockevent device with a dummy rate and sets its final rate through
clockevents_config() called from its ->set_state_oneshot().
This patch moves the setting of the clockevent device's rate to its
registration.
I checked all current em_sti users in arch/arm/mach-shmobile and right now,
none of them changes any rate in any clock tree relevant to em_sti after
their respective time_init(). Since all em_sti instances are created after
time_init(), none of them should ever observe any clock rate changes.
- Determine the ->rate value in em_sti_probe() at device probing rather
than at first usage.
- Set the clockevent device's rate at its registration.
- Although not strictly necessary for the upcoming clockevent core changes,
set the clocksource's rate at its registration for consistency.
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Currently, the em_sti driver prepares and enables the needed clock in
em_sti_enable(), potentially called through its clockevent device's
->set_state_oneshot().
However, the clk_prepare() step may sleep whereas tick_program_event() and
thus, ->set_state_oneshot(), can be called in atomic context.
Split the clk_prepare_enable() in em_sti_enable() into two steps:
- prepare the clock at device probing via clk_prepare()
- and enable it in em_sti_enable() via clk_enable().
Slightly reorder resource initialization in em_sti_probe() in order to
facilitate error handling in later patches.
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
