| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Register the PLL configuration data for APLL and KPLL on Exynos5420. This
configuration data table specifies PLL coefficients for supported PLL
clock speeds when a 24MHz clock is supplied as the input clock source
for these PLLs.
Cc: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Arjun K.V <arjun.kv@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
Prior to suspending the system, we need to ensure that certain
clock source and gate registers are unmasked.
while at it, add these clks to save/restore list also.
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
Array of struct of_device_id may be be const as expected by
of_match_table field and of_find_matching_node_and_match() function.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
Enable ARMCLK down feature on Exynos3250 SoC. The frequency of
ARMCLK will be reduced upon entering idle mode (WFI or WFE).
The feature behaves like very fast cpufreq ondemand governor.
The patch uses simillar settings as Exynos5250 (clk-exynos5250.c),
except it disables clock up feature.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
Enable ARMCLK down feature on all Exynos4 SoCs. The frequency of
ARMCLK will be reduced upon entering idle mode (WFI or WFE).
The feature behaves like very fast cpufreq ondemand governor. In idle
mode this reduces energy consumption on full frequency chosen by
cpufreq governor by approximately:
- Trats2: 6.5% (153 mA -> 143 mA)
- Trats: 33.0% (180 mA -> 120 mA)
- Gear1: 27.0% (180 mA -> 130 mA)
The patch uses simillar settings as Exynos5250 (clk-exynos5250.c),
except it disables clock up feature and on Exynos4412 ARMCLK down is
enabled for all 4 cores.
Tested on Trats board (Exynos4210), Trats2 board (Exynos4412) and
Samsung Gear 1 (Exynos4212).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
This patch introduces a driver that handles configuration of CLKOUT pin
of Exynos SoCs that can be used to output certain clocks from inside of
the SoC to a dedicated output pin.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
This patch adds definitions of clocks that are used to drive clock
output signals of particular CMU sub-blocks that are then fed to PMU and
handled by Exynos CLKOUT driver added in further patch.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next-sunxi
Allwinner clocks additions for 3.17
This pull request adds support for the clocks found in the newly supported
Allwinner A23 clocks.
|
|
This patch adds missing definitions of clocks from CPU and DMC clock
domains, which are necessary to properly represent CLKOUT clock hierarchy
added in further patch.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into clk-next-msm
qcom clock changes for 3.17
These patches add support for a handful of Qualcomm's SoC clock
controllers: APQ8084 gcc and mmcc, IPQ8064 gcc, and APQ8064.
There's also a small collection of bug fixes that aren't critical
-rc worthy regressions because the consumer drivers aren't present
or using the buggy clocks and one optimization for HDMI.
|
|
clk-next-ti
|
|
This patch adds helper functions to configure clock parents and rates
as specified through 'assigned-clock-parents', 'assigned-clock-rates'
DT properties for a clock provider or clock consumer device.
The helpers are now being called by the bus code for the platform, I2C
and SPI busses, before the driver probing and also in the clock core
after registration of a clock provider.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Merge "Samsung exynos cpuidle update for v3.17" from Kukjin Kim:
- add callbacks exynos_suspend() and exynos_powered_up()
for support cpuidle through mcpm
- skip exynos_cpuidle for exynos5420 because is uses
cpuidle-big-liggle generic cpuidle driver
- add generic functions to calculate cpu number is used
for pmu and this is required for exynos5420 multi-cluster
- add of_device_id structure for big.LITTLE cpuidle and
add "samsung,exynos5420" compatible string for exynos5420
* tag 'exynos-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: populate suspend and powered_up callbacks for mcpm
ARM: EXYNOS: do not allow cpuidle registration for exynos5420
cpuidle: big.LITTLE: init driver for exynos5420
cpuidle: big.LITTLE: Add ARCH_EXYNOS entry in config
ARM: EXYNOS: add generic function to calculate cpu number
cpuidle: big.LITTLE: add of_device_id structure
+ Linux 3.16-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
Merge "Samsung cleanup for v3.17" from Kukjin Kim:
Most of them are for exynos SoCs, remove useless codes and update for
PMU consolidation.
- remove unnecessary header file in mach-exynos/pmu.c
- remove unused code in mach-exynos/common.h
- remove mach-exynos/regs-pmu.h dependency from PD
- remove file path from comment section in mach-exynos
- move SYSREG definitions into mach-exynos/regs-sys.h
- add mapping PMU base address via DT for PMU cleanup
- use staic in mach-exynos/common.h
- update Samsung UART config options for low-level debug
* tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add support for mapping PMU base address via DT
ARM: EXYNOS: Remove "linux/bug.h" from pmu.c
ARM: EXYNOS: Remove regs-pmu.h header dependency from pm_domain
ARM: EXYNOS: Remove file path from comment section
ARM: EXYNOS: Move SYSREG definition into sys-reg specific file
ARM: EXYNOS: Make exynos machine_ops as static
ARM: EXYNOS: Remove unused code in common.h
ARM: debug: Update Samsung UART config options
+ Linux 3.16-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Since there is no more support for board files, this patch removes
legacy non-DT support from the clock driver as well, including
unnecessary clkdev aliases.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds a driver for clock controller being a part of Audio
Subsystem present on S5PV210 and compatible SoCs. It is used to provide
clocks for other IP blocks of this subsystem.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds new, Common Clock Framework-based clock driver for Samsung
S5PV210 and compatible SoCs. The driver is just added, without enabling it yet.
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[t.figa: Added support for other SoC variants and clock output. Fixed
remaining minor issues.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This commit converts the PMC support code to a platform driver. Because
the boot process needs to call into this driver very early, also set up
a minimal environment via an early initcall.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
In order to not clutter the include/linux directory with SoC specific
headers, move the Tegra-specific headers out into a separate directory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This commit extends the existing clk-cpu driver used on Marvell Armada
XP platforms to support the dynamic frequency scaling of the CPU
clock. Non-dynamic frequency change was already supported (and used
before secondary CPUs are started), but the dynamic frequency change
requires a completely different procedure.
In order to achieve this, the clk_cpu_set_rate() function is reworked
to handle two separate cases:
- The case where the clock is enabled, which is the new dynamic
frequency change code, implemented in clk_cpu_on_set_rate(). This
part will be used for cpufreq activities.
- The case where the clock is disabled, which is the existing
frequency change code, moved in clk_cpu_off_set_rate(). This part
is already used to set the clock frequency of the secondary CPUs
before starting them.
In order to implement the dynamic frequency change function, we need
to access the PMU DFS registers, which are outside the currently
mapped "Clock Complex" registers, so a new area of registers is now
mapped. This affects the Device Tree binding, but we are careful to do
it in a backward-compatible way (by allowing the second pair of
registers to be non-existent, and in this case, ensuring
clk_cpu_on_set_rate() returns an error).
Note that technically speaking, the clk_cpu_on_set_rate() does not do
the entire procedure needed to change the frequency dynamically, as it
involves touching a number of PMSU registers. This is done through a
clock notifier registered by the PMSU driver in followup commits.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1404920715-19834-4-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The APQ8064 multimedia clock controller is fairly similar to the
8960 multimedia clock controller, except that gfx2d0/1 has been
removed and the gfx3d frequency is slightly faster when using the
newly introduced PLL15. We also add vcap clocks and a couple new
TV clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Some SR type PLLs need to be configured for a certain rate when
linux boots. Add support for these types of PLLs so that we can
program PLL15's rate on apq8064.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The mdp_lut_clk isn't a child of the mdp_clk. Instead it's the
child of the mdp_src clock. Fix it.
Fixes: 6d00b56fe "clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Sometimes we need to program PLLs with a fixed rate
configuration during driver probe. Doing this after we register
the PLLs with the clock framework causes the common clock
framework to assume the rate of the PLLs are 0. This causes all
sorts of problems for rate recalculations because the common
clock framework caches the rate once at registration time unless
a flag is set to always recalculate the rates.
Split the qcom_cc_probe() function into two pieces, map and
everything else, so that drivers which need to configure some
PLL rates or otherwise twiddle bits in the clock controller can
do so before registering clocks. This allows us to properly
detect the rates of PLLs that are programmed at boot.
Fixes: 49fc825f0cc2 "clk: qcom: Consolidate common probe code"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Clocks that don't have a pre-divider don't list any pre-divider
in their frequency tables, but their tables are initialized using
aggregate initializers. Use tagged initializers so we properly
assign the m and n values for each frequency. Furthermore, the
mmcc_pxo_pll8_pll2_pll3 array improperly mapped the second
element to pll2 instead of pll8, causing the clock driver to
recalculate the wrong rate for any clocks using this array along
with a rate that uses pll2. Plus the .num_parents field is 3
instead of 4 so you can't even switch the parent to pll3. Finally
I noticed that the jpegd clock improperly indicates that the
pre-divider width is only 2, when it's actually 4 bits wide.
Fixes: 6d00b56fe "clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)"
Tested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
In the case of HDMI clocks, we want to bypass the RCG's ability
to divide the output clock and pass through the parent HDMI PLL
rate. Add a simple set of clk_ops to configure the RCG to do
this. This removes the need to keep adding more frequency entries
to the tv_src clock whenever we want to support a new rate.
Tested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add a driver for the global clock controller found on IPQ8064 based
platforms. This should allow most non-multimedia device drivers to probe
and control their clocks.
This is currently missing clocks for USB HSIC and networking devices.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add support for the multimedia clock controller found on the APQ8084
based platforms. This will allow the multimedia device drivers to
control their clocks.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
[sboyd: Rework parent mapping to avoid conflicts]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The CLK_IGNORE_UNUSED flag was added on all the system clocks because of the
ddrck. Now that it is handled by the ram controller driver, we can drop it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
This patch adds "allwinner,sun8i-a23-apb0-gates-clk", a A23 specific
compatible to the sun6i-a31-apb0-gates clock driver, along with the
gate bitmap.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
sun6i-apb0-gates uses the "clock-indices" DT property to indicate
valid gate bits or holes in between. However, the rest of sunxi
clock drivers use bitmaps for this purpose.
This patch modifies sun6i-apb0-gates to use bitmaps as well, to be
consistent with the sunxi platform. Also add the missing call to
clk_register_clkdev, so system clock lookups will work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
git://git.linaro.org/people/mike.turquette/linux
Pull clock driver fixes from Mike Turquette:
"This batch of fixes is for a handful of clock drivers from Allwinner,
Samsung, ST & TI. Most of them are of the "this hardware won't work
without this fix" variety, including patches that fix platforms that
did not boot under certain configurations. Other fixes are the result
of changes to the clock core introduced in 3.15 that had subtle
impacts on the clock drivers.
There are no fixes to the clock framework core in this pull request"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: spear3xx: Set proper clock parent of uart1/2
clk: spear3xx: Use proper control register offset
clk: qcom: HDMI source sel is 3 not 2
clk: sunxi: fix devm_ioremap_resource error detection code
clk: s2mps11: Fix double free corruption during driver unbind
clk: ti: am43x: Fix boot with CONFIG_SOC_AM33XX disabled
clk: exynos5420: Remove aclk66_peric from the clock tree description
clk/exynos5250: fix bit number for tv sysmmu clock
clk: s3c64xx: Hookup SPI clocks correctly
clk: samsung: exynos4: Remove SRC_MASK_ISP gates
clk: samsung: add more aliases for s3c24xx
clk: samsung: fix several typos to fix boot on s3c2410
clk: ti: set CLK_SET_RATE_NO_REPARENT for ti,mux-clock
clk: ti: am43x: Fix boot with CONFIG_SOC_AM33XX disabled
clk: ti: dra7: return error code in failure case
clk: ti: apll: not allocating enough data
|
|
Add the clock tree definition for the new rk3288 SoC.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
This adds a clock driver that handles the specific muxes, dividers and gates
of rk3188 and rk3066 SoCs.
The structure of the clock list resembles the arrangement of their
counterparts in the clock architecture diagrams found in the SoC
documentation.
Clocks exported to the clock provider are currently limited to well known
or measured ones. So additional clock exports may be necessary in the future.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
All Rockchip SoCs at least down to the ARM9-based RK28xx include the reset-
controller for SoC peripherals in their clock controller.
While the older SoCs (ARM9 and Cortex-A8) use a regular scheme to change
register values, the Cortex-A9 SoCs use a hiword-mask making locking unecessary.
To be compatible with both schemes the reset controller takes a flag to
decide which scheme to use, similar to the other HIWORD_MASK flags used in the
clock framework.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
All known Rockchip SoCs down to the RK28xx (ARM9) use a similar pattern to
handle their plls:
|--\
xin32k ----------------|mux\
xin24m -----| pll |----|pll|--- pll output
\---------------|src/
|--/
The pll output is sourced from 1 of 3 sources, the actual pll being one of
them. To change the pll frequency it is imperative to remux it to another
source beforehand. This is done by adding a clock-listener to the pll that
handles the remuxing before and after the rate change.
The output mux is implemented as a separate clock to make use of already
existing common-clock features for disabling the pll if one of the other
two sources is used.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
This adds infrastructure for registering clock branches. On Rockchip SoCs
most clock branches are a combination of mux,divider and gate components,
thus a composite clock is used when appropriate.
Clock branches are supposed to be declared in an array using the COMPOSITE*
or MUX, etc makros defined in the header and then registered using
rockchip_clk_register_branches.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The function pointer population and sanity checking logic got a bit ugly
with the advent of the .determine_rate callback. Clean it up.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
This allows readl-only composite clocks by making mux_ops->set_parent and
divider_ops->round_rate/set_rate optional.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
mux_ops->set_parent
In case the rate_hw does not implement determine_rate, but only round_rate
we fallback to best_parent selection if mux_hw is present and support
reparenting.
This also fixes a rate calculation problem when using the standard div and
mux ops, as in this case currently only the mux->determine_rate is used
in the composite rate calculation.
So when for example the composite clock has two parents at 600 and 800MHz,
the requested rate is 75MHz, which the divider could provide, without this
change the rate would be set 600MHz ignoring the divider completely.
This may be way out of spec for the component.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[heiko@sntech.de: fixed output return a rate instead of the diff]
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
Tested-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
|
|
The uarts only work when the parent is ras_ahb_clk. The stale 3.5
based ST tree does this in the board file.
Add it to the clk init function. Not pretty, but the mess there is
amazing anyway.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The control register is at offset 0x10, not 0x0. This is wreckaged
since commit 5df33a62c (SPEAr: Switch to common clock framework).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Add the necessary clocks for SATA, PCIe and UFS to the
APQ8084 global clock controller (GCC). This will allow
the above device drivers to control their clocks.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This patch adds support for the global clock controller found on
the APQ8084 based devices. This includes UART, I2C, SPI etc.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add in the handful of new clocks and introduce a new reset table
with the few new resets.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This patch adds clocks necessary for SD card controller on apq8064 SOC.
Without this patch the clocks are not visible to the sdcc driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Follow dt clock naming convention for PCIe clocks.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[viresh: fixed logs/cclist]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Adds IDs for MUX clocks to be used by power domain for MFC
for doing re-parenting while pd on/off.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
