| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 5a3ae7b314a2259b1188b22b392f5eba01e443ee upstream.
The ftrace trampoline code (which deals with modules loaded out of
BL range of the core kernel) uses plt_entries_equal() to check whether
the per-module trampoline equals a zero buffer, to decide whether the
trampoline has already been initialized.
This triggers a BUG() in the opcode manipulation code, since we end
up checking the ADRP offset of a 0x0 opcode, which is not an ADRP
instruction.
So instead, add a helper to check whether a PLT is initialized, and
call that from the frace code.
Cc: <stable@vger.kernel.org> # v5.0
Fixes: bdb85cd1d206 ("arm64/module: switch to ADRP/ADD sequences for PLT entries")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1e6f5440a6814d28c32d347f338bfef68bc3e69d upstream.
Calling dump_backtrace() with a pt_regs argument corresponding to
userspace doesn't make any sense and our unwinder will simply print
"Call trace:" before unwinding the stack looking for user frames.
Rather than go through this song and dance, just return early if we're
passed a user register state.
Cc: <stable@vger.kernel.org>
Fixes: 1149aad10b1e ("arm64: Add dump_backtrace() in show_regs")
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6fd8b9780ec1a49ac46e0aaf8775247205e66231 upstream.
Several rk3328 based boards experience high rgmii tx error rates.
This is due to several pins in the rk3328.dtsi rgmii pinmux that are
missing a defined pull strength setting.
This causes the pinmux driver to default to 2ma (bit mask 00).
These pins are only defined in the rk3328.dtsi, and are not listed in
the rk3328 specification.
The TRM only lists them as "Reserved"
(RK3328 TRM V1.1, 3.3.3 Detail Register Description, GRF_GPIO0B_IOMUX,
GRF_GPIO0C_IOMUX, GRF_GPIO0D_IOMUX).
However, removal of these pins from the rgmii pinmux definition causes
the interface to fail to transmit.
Also, the rgmii tx and rx pins defined in the dtsi are not consistent
with the rk3328 specification, with tx pins currently set to 12ma and
rx pins set to 2ma.
Fix this by setting tx pins to 8ma and the rx pins to 4ma, consistent
with the specification.
Defining the drive strength for the undefined pins eliminated the high
tx packet error rate observed under heavy data transfers.
Aligning the drive strength to the TRM values eliminated the occasional
packet retry errors under iperf3 testing.
This allows much higher data rates with no recorded tx errors.
Tested on the rk3328-roc-cc board.
Fixes: 52e02d377a72 ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a8772e5d826d0f61f8aa9c284b3ab49035d5273d upstream.
This patch makes USB ports functioning again.
Fixes: 955bebde057e ("arm64: dts: rockchip: add rk3328-rock64 board")
Cc: stable@vger.kernel.org
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Tomohiro Mayama <parly-gh@iris.mystia.org>
Tested-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 045afc24124d80c6998d9c770844c67912083506 upstream.
Rather embarrassingly, our futex() FUTEX_WAKE_OP implementation doesn't
explicitly set the return value on the non-faulting path and instead
leaves it holding the result of the underlying atomic operation. This
means that any FUTEX_WAKE_OP atomic operation which computes a non-zero
value will be reported as having failed. Regrettably, I wrote the buggy
code back in 2011 and it was upstreamed as part of the initial arm64
support in 2012.
The reasons we appear to get away with this are:
1. FUTEX_WAKE_OP is rarely used and therefore doesn't appear to get
exercised by futex() test applications
2. If the result of the atomic operation is zero, the system call
behaves correctly
3. Prior to version 2.25, the only operation used by GLIBC set the
futex to zero, and therefore worked as expected. From 2.25 onwards,
FUTEX_WAKE_OP is not used by GLIBC at all.
Fix the implementation by ensuring that the return value is either 0
to indicate that the atomic operation completed successfully, or -EFAULT
if we encountered a fault when accessing the user mapping.
Cc: <stable@kernel.org>
Fixes: 6170a97460db ("arm64: Atomic operations")
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e7dfb6d04e4715be1f3eb2c60d97b753fd2e4516 upstream.
The function argument for the ISC_D0 on PC9 was incorrect. According to
the documentation it should be 'C' aka 3.
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Fixes: 7f16cb676c00 ("ARM: at91/dt: add sama5d2 pinmux")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8dbc4d5ddb59f49cb3e85bccf42a4720b27a6576 upstream.
The Problem:
On ASUS Tinker Board S, when booting from the eMMC, and there is card
in the sd slot, there are constant errors.
Also when warm reboot, uboot can not access the sd slot
Cause:
Identified by Robin Murphy @ ARM. The Card Detect on rk3288
devices is pulled up by vccio-sd; so when the regulator powers this
off, card detect gives spurious errors. A second problem, is during
power down, vccio-sd apprears to be powered down. This causes a
problem when warm rebooting from the sd card. This was identified by
Jonas Karlman.
History:
A common fault on these rk3288 board, which impliment the reference
design.
When this arose before:
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-August/281153.html
And Ulf and Jaehoon clearly said this was a broken card detect design,
which should be solved via polling
Solution:
Hence broken-cd is set as a property. This cures the errors. The
powering down of vccio-sd during reboot is cured by adding
regulator-boot-on.
This solutions has been fairly widely reviewed and tested.
Fixes: e58c5e739d6f ("ARM: dts: rockchip: move shared tinker-board nodes to a common dtsi")
Cc: stable@vger.kernel.org
[Heiko: slightly inaccurate fixes but tinker is a sbc (aka like a Pi) where
we can hopefully expect people not to rely on overly old stable kernels]
Signed-off-by: David Summers <beagleboard@davidjohnsummers.uk>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4f96dc0a3e79ec257a2b082dab3ee694ff88c317 upstream.
Correctly map the regulators used by tlv320aic3106.
Both 1.8V and 3.3V for the codec is derived from VBAT via fixed regulators.
Cc: <Stable@vger.kernel.org> # v4.14+
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6691370646e844be98bb6558c024269791d20bd7 upstream.
Correctly map the regulators used by tlv320aic3106.
Both 1.8V and 3.3V for the codec is derived from VBAT via fixed regulators.
Cc: <Stable@vger.kernel.org> # v4.14+
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6b2fde3dbfab6ebc45b0cd605e17ca5057ff9a3b upstream.
The following error can be seen during boot:
of: /cpus/cpu@501: Couldn't find opp node
Change cpu nodes to use operating-points-v2 in order to fix this.
Fixes: ce76de984649 ("ARM: dts: rockchip: convert rk3288 to operating-points-v2")
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3e2cf62efec52fb49daed437cc486c3cb9a0afa2 upstream.
In order to request dynamic allocationn of GPIO IDs, a negative number
should be passed as a base GPIO ID via platform data. Unfortuntely,
commit 771e53c4d1a1 ("ARM: OMAP1: ams-delta: Drop board specific global
GPIO numbers") didn't follow that rule while switching to dynamically
allocated GPIO IDs for Amstrad Delta latches, making their IDs
overlapping with those already assigned to OMAP GPIO devices. Fix it.
Fixes: 771e53c4d1a1 ("ARM: OMAP1: ams-delta: Drop board specific global GPIO numbers")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 10a16997db3d99fc02c026cf2c6e6c670acafab0 upstream.
RISC-V syscall arguments are located in orig_a0,a1..a5 fields
of struct pt_regs.
Due to an off-by-one bug and a bug in pointer arithmetic
syscall_get_arguments() was reading s3..s7 fields instead of a1..a5.
Likewise, syscall_set_arguments() was writing s3..s7 fields
instead of a1..a5.
Link: http://lkml.kernel.org/r/20190329171221.GA32456@altlinux.org
Fixes: e2c0cdfba7f69 ("RISC-V: User-facing API")
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Will Drewry <wad@chromium.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: linux-riscv@lists.infradead.org
Cc: stable@vger.kernel.org # v4.15+
Acked-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ede885ecb2cdf8a8dd5367702e3d964ec846a2d5 upstream.
get_num_contig_pages() could potentially overflow int so make its type
consistent with its usage.
Reported-by: Cfir Cohen <cfir@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f324fa58327791b2696628b31480e7e21c745706 upstream.
When setting the instruction pointer on PA-RISC we also need
to set the back of the instruction queue to the new offset, otherwise
we will execute on instruction from the new location, and jumping
back to the old location stored in iaoq_b.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes: 75ebedf1d263 ("parisc: Add HAVE_REGS_AND_STACK_ACCESS_API feature")
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 45efd871bf0a47648f119d1b41467f70484de5bc upstream.
While working on kretprobes for PA-RISC I was wondering while the
kprobes sanity test always fails on kretprobes. This is caused by
returning gpr20 instead of gpr28.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d006e95b5561f708d0385e9677ffe2c46f2ae345 upstream.
While adding LASI support to QEMU, I noticed that the QEMU detection in
the kernel happens much too late. For example, when a LASI chip is found
by the kernel, it registers the LASI LED driver as well. But when we
run on QEMU it makes sense to avoid spending unnecessary CPU cycles, so
we need to access the running_on_QEMU flag earlier than before.
This patch now makes the QEMU detection the fist task of the Linux
kernel by moving it to where the kernel enters the C-coding.
Fixes: 310d82784fb4 ("parisc: qemu idle sleep support")
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 09f91381fa5de1d44bc323d8bf345f5d57b3d9b5 upstream.
Various rk3328 based boards experience occasional sdmmc0 write errors.
This is due to the rk3328.dtsi tx drive levels being set to 4ma, vs
8ma per the rk3328 datasheet default settings.
Fix this by setting the tx signal pins to 8ma.
Inspiration from tonymac32's patch,
https://github.com/ayufan-rock64/linux-kernel/commit/dc1212b347e0da17c5460bcc0a56b07d02bac3f8
Fixes issues on the rk3328-roc-cc and the rk3328-rock64 (as per the
above commit message).
Tested on the rk3328-roc-cc board.
Fixes: 52e02d377a72 ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
OpenBMC-Staging-Count: 1
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
OpenBMC-Staging-Count: 1
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This is the 5.0.7 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
[ Upstream commit 5347a0203709d5039a74d7c94e23519eee478094 ]
The quirk code currently detects all compatible I2C chips with a shared
IRQ line on all I2C busses, adds them into a list, and registers a bus
notifier. For every chip for which the bus notifier triggers, the quirk
code performs I2C transfer on that I2C bus for all addresses in the list.
The problem is that this may generate transfers to non-existing chips on
systems with multiple I2C busses.
This patch adds a check to verify that the I2C bus to which the chip with
shared IRQ is attached to matches the I2C bus of the chip which triggered
the bus notifier and only starts the I2C transfer if they match.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d071ae09a4a1414c1433d5ae9908959a7325b0ad ]
Accessing per-CPU variables is done by finding the offset of the
variable in the per-CPU block and adding it to the address of the
respective CPU's block.
Section 3.10.8 of ld.bfd's documentation states:
For expressions involving numbers, relative addresses and absolute
addresses, ld follows these rules to evaluate terms:
Other binary operations, that is, between two relative addresses
not in the same section, or between a relative address and an
absolute address, first convert any non-absolute term to an
absolute address before applying the operator."
Note that LLVM's linker does not adhere to the GNU ld's implementation
and as such requires implicitly-absolute terms to be explicitly marked
as absolute in the linker script. If not, it fails currently with:
ld.lld: error: ./arch/x86/kernel/vmlinux.lds:153: at least one side of the expression must be absolute
ld.lld: error: ./arch/x86/kernel/vmlinux.lds:154: at least one side of the expression must be absolute
Makefile:1040: recipe for target 'vmlinux' failed
This is not a functional change for ld.bfd which converts the term to an
absolute symbol anyways as specified above.
Based on a previous submission by Tri Vo <trong@android.com>.
Reported-by: Dmitry Golovin <dima@golovin.in>
Signed-off-by: Rafael Ávila de Espíndola <rafael@espindo.la>
[ Update commit message per Boris' and Michael's suggestions. ]
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
[ Massage commit message more, fix typos. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Dmitry Golovin <dima@golovin.in>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Cao Jin <caoj.fnst@cn.fujitsu.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tri Vo <trong@android.com>
Cc: dima@golovin.in
Cc: morbo@google.com
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20181219190145.252035-1-ndesaulniers@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 927185c124d62a9a4d35878d7f6d432a166b74e3 ]
The kernel uses the OUTPUT_FORMAT linker script command in it's linker
scripts. Most of the time, the -m option is passed to the linker with
correct architecture, but sometimes (at least for x86_64) the -m option
contradicts the OUTPUT_FORMAT directive.
Specifically, arch/x86/boot and arch/x86/realmode/rm produce i386 object
files, but are linked with the -m elf_x86_64 linker flag when building
for x86_64.
The GNU linker manpage doesn't explicitly state any tie-breakers between
-m and OUTPUT_FORMAT. But with BFD and Gold linkers, OUTPUT_FORMAT
overrides the emulation value specified with the -m option.
LLVM lld has a different behavior, however. When supplied with
contradicting -m and OUTPUT_FORMAT values it fails with the following
error message:
ld.lld: error: arch/x86/realmode/rm/header.o is incompatible with elf_x86_64
Therefore, just add the correct -m after the incorrect one (it overrides
it), so the linker invocation looks like this:
ld -m elf_x86_64 -z max-page-size=0x200000 -m elf_i386 --emit-relocs -T \
realmode.lds header.o trampoline_64.o stack.o reboot.o -o realmode.elf
This is not a functional change for GNU ld, because (although not
explicitly documented) OUTPUT_FORMAT overrides -m EMULATION.
Tested by building x86_64 kernel with GNU gcc/ld toolchain and booting
it in QEMU.
[ bp: massage and clarify text. ]
Suggested-by: Dmitry Golovin <dima@golovin.in>
Signed-off-by: George Rimar <grimar@accesssoftek.com>
Signed-off-by: Tri Vo <trong@android.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Tri Vo <trong@android.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Michael Matz <matz@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: morbo@google.com
Cc: ndesaulniers@google.com
Cc: ruiu@google.com
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190111201012.71210-1-trong@android.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 81b61324922c67f73813d8a9c175f3c153f6a1c6 ]
On pseries systems, performing a partition migration can result in
altering the nodes a CPU is assigned to on the destination system. For
exampl, pre-migration on the source system CPUs are in node 1 and 3,
post-migration on the destination system CPUs are in nodes 2 and 3.
Handling the node change for a CPU can cause corruption in the slab
cache if we hit a timing where a CPUs node is changed while cache_reap()
is invoked. The corruption occurs because the slab cache code appears
to rely on the CPU and slab cache pages being on the same node.
The current dynamic updating of a CPUs node done in arch/powerpc/mm/numa.c
does not prevent us from hitting this scenario.
Changing the device tree property update notification handler that
recognizes an affinity change for a CPU to do a full DLPAR remove and
add of the CPU instead of dynamically changing its node resolves this
issue.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael W. Bringmann <mwb@linux.vnet.ibm.com>
Tested-by: Michael W. Bringmann <mwb@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eddd0b332304d554ad6243942f87c2fcea98c56b ]
The ppc64 specific implementation of the reliable stacktracer,
save_stack_trace_tsk_reliable(), bails out and reports an "unreliable
trace" whenever it finds an exception frame on the stack. Stack frames
are classified as exception frames if the STACK_FRAME_REGS_MARKER
magic, as written by exception prologues, is found at a particular
location.
However, as observed by Joe Lawrence, it is possible in practice that
non-exception stack frames can alias with prior exception frames and
thus, that the reliable stacktracer can find a stale
STACK_FRAME_REGS_MARKER on the stack. It in turn falsely reports an
unreliable stacktrace and blocks any live patching transition to
finish. Said condition lasts until the stack frame is
overwritten/initialized by function call or other means.
In principle, we could mitigate this by making the exception frame
classification condition in save_stack_trace_tsk_reliable() stronger:
in addition to testing for STACK_FRAME_REGS_MARKER, we could also take
into account that for all exceptions executing on the kernel stack
- their stack frames's backlink pointers always match what is saved
in their pt_regs instance's ->gpr[1] slot and that
- their exception frame size equals STACK_INT_FRAME_SIZE, a value
uncommonly large for non-exception frames.
However, while these are currently true, relying on them would make
the reliable stacktrace implementation more sensitive towards future
changes in the exception entry code. Note that false negatives, i.e.
not detecting exception frames, would silently break the live patching
consistency model.
Furthermore, certain other places (diagnostic stacktraces, perf, xmon)
rely on STACK_FRAME_REGS_MARKER as well.
Make the exception exit code clear the on-stack
STACK_FRAME_REGS_MARKER for those exceptions running on the "normal"
kernel stack and returning to kernelspace: because the topmost frame
is ignored by the reliable stack tracer anyway, returns to userspace
don't need to take care of clearing the marker.
Furthermore, as I don't have the ability to test this on Book 3E or 32
bits, limit the change to Book 3S and 64 bits.
Fixes: df78d3f61480 ("powerpc/livepatch: Implement reliable stack tracing for the consistency model")
Reported-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5388a5b82199facacd3d7ac0d05aca6e8f902fed ]
machine_crash_nonpanic_core() does this:
while (1)
cpu_relax();
because the kernel has crashed, and we have no known safe way to deal
with the CPU. So, we place the CPU into an infinite loop which we
expect it to never exit - at least not until the system as a whole is
reset by some method.
In the absence of erratum 754327, this code assembles to:
b .
In other words, an infinite loop. When erratum 754327 is enabled,
this becomes:
1: dmb
b 1b
It has been observed that on some systems (eg, OMAP4) where, if a
crash is triggered, the system tries to kexec into the panic kernel,
but fails after taking the secondary CPU down - placing it into one
of these loops. This causes the system to livelock, and the most
noticable effect is the system stops after issuing:
Loading crashdump kernel...
to the system console.
The tested as working solution I came up with was to add wfe() to
these infinite loops thusly:
while (1) {
cpu_relax();
wfe();
}
which, without 754327 builds to:
1: wfe
b 1b
or with 754327 is enabled:
1: dmb
wfe
b 1b
Adding "wfe" does two things depending on the environment we're running
under:
- where we're running on bare metal, and the processor implements
"wfe", it stops us spinning endlessly in a loop where we're never
going to do any useful work.
- if we're running in a VM, it allows the CPU to be given back to the
hypervisor and rescheduled for other purposes (maybe a different VM)
rather than wasting CPU cycles inside a crashed VM.
However, in light of erratum 794072, Will Deacon wanted to see 10 nops
as well - which is reasonable to cover the case where we have erratum
754327 enabled _and_ we have a processor that doesn't implement the
wfe hint.
So, we now end up with:
1: wfe
b 1b
when erratum 754327 is disabled, or:
1: dmb
nop
nop
nop
nop
nop
nop
nop
nop
nop
nop
wfe
b 1b
when erratum 754327 is enabled. We also get the dmb + 10 nop
sequence elsewhere in the kernel, in terminating loops.
This is reasonable - it means we get the workaround for erratum
794072 when erratum 754327 is enabled, but still relinquish the dead
processor - either by placing it in a lower power mode when wfe is
implemented as such or by returning it to the hypervisior, or in the
case where wfe is a no-op, we use the workaround specified in erratum
794072 to avoid the problem.
These as two entirely orthogonal problems - the 10 nops addresses
erratum 794072, and the wfe is an optimisation that makes the system
more efficient when crashed either in terms of power consumption or
by allowing the host/other VMs to make use of the CPU.
I don't see any reason not to use kexec() inside a VM - it has the
potential to provide automated recovery from a failure of the VMs
kernel with the opportunity for saving a crashdump of the failure.
A panic() with a reboot timeout won't do that, and reading the
libvirt documentation, setting on_reboot to "preserve" won't either
(the documentation states "The preserve action for an on_reboot event
is treated as a destroy".) Surely it has to be a good thing to
avoiding having CPUs spinning inside a VM that is doing no useful
work.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 72cd4064fccaae15ab84d40d4be23667402df4ed ]
ARMv8M introduces support for Security extension to M class, among
other things it affects exception handling, especially, encoding of
EXC_RETURN.
The new bits have been added:
Bit [6] Secure or Non-secure stack
Bit [5] Default callee register stacking
Bit [0] Exception Secure
which conflicts with hard-coded value of EXC_RETURN:
In fact, we only care of few bits:
Bit [3] Mode (0 - Handler, 1 - Thread)
Bit [2] Stack pointer selection (0 - Main, 1 - Process)
We can toggle only those bits and left other bits as they were on
exception entry.
It is basically, what patch does - saves EXC_RETURN when we do
transition form Thread to Handler mode (it is first svc), so later
saved value is used instead of EXC_RET_THREADMODE_PROCESSSTACK.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3e3380d0675d5e20b0af067d60cb947a4348bf9b ]
Improve the DTS files by removing all the leading "0x" and zeros to fix
the following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[vzapolskiy: fixed commit message to pass checkpatch.pl test]
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 840018668ce2d96783356204ff282d6c9b0e5f66 ]
When pmu::setup_aux() is called the coresight PMU needs to know which
sink to use for the session by looking up the information in the
event's attr::config2 field.
As such simply replace the cpu information by the complete perf_event
structure and change all affected customers.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki Poulouse <suzuki.poulose@arm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-s390@vger.kernel.org
Link: http://lkml.kernel.org/r/20190131184714.20388-2-mathieu.poirier@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ebb0e13ead2ddc186a80b1b0235deeefc5a1a667 ]
'regno' is directly controlled by user space, hence leading to a potential
exploitation of the Spectre variant 1 vulnerability.
On PTRACE_SETREGS and PTRACE_GETREGS requests, user space passes the
register number that would be read or written. This register number is
called 'regno' which is part of the 'addr' syscall parameter.
This 'regno' value is checked against the maximum pt_regs structure size,
and then used to dereference it, which matches the initial part of a
Spectre v1 (and Spectre v1.1) attack. The dereferenced value, then,
is returned to userspace in the GETREGS case.
This patch sanitizes 'regno' before using it to dereference pt_reg.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ccec81e4251f5a5421e02874e394338a897056ca ]
When efi=noruntime or efi=oldmap is used on the kernel command line, EFI
services won't be available in the second kernel, therefore the second
kernel will not be able to get the ACPI RSDP address from firmware by
calling EFI services and so it won't boot.
Commit
e6e094e053af ("x86/acpi, x86/boot: Take RSDP address from boot params if available")
added an acpi_rsdp_addr field to boot_params which stores the RSDP
address for other kernel users.
Recently, after
3a63f70bf4c3 ("x86/boot: Early parse RSDP and save it in boot_params")
the acpi_rsdp_addr will always be filled with a valid RSDP address.
So fill in that value into the second kernel's boot_params thus ensuring
that the second kernel receives the RSDP value from the first kernel.
[ bp: massage commit message. ]
Signed-off-by: Kairui Song <kasong@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Chao Fan <fanc.fnst@cn.fujitsu.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: kexec@lists.infradead.org
Cc: Philipp Rudo <prudo@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Cc: Yannik Sembritzki <yannik@sembritzki.me>
Link: https://lkml.kernel.org/r/20190204173852.4863-1-kasong@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 29f0023d01f063feacfc404f0446905aee4f82ee ]
According to the Odroid-C1+ schematics the Ethernet TXD1 signal is
routed to GPIOH_5 and the TXD0 signal is routed to GPIOH_6.
The public S805 datasheet shows that TXD0 can be routed to DIF_2_P and
TXD1 can be routed to DIF_2_N instead.
The pin groups eth_txd0_0 (GPIOH_6) and eth_txd0_1 (DIF_2_P) are both
configured as Ethernet TXD0 and TXD1 data lines in meson8b.dtsi. At the
same time eth_txd1_0 (GPIOH_5) and eth_txd1_1 (DIF_2_N) are configured
as TXD0 and TXD1 data lines as well.
This results in a bad Ethernet receive performance. Presumably this is
due to the eth_txd0 and eth_txd1 signal being routed to the wrong pins.
As a result of that data can only be transmitted on eth_txd2 and
eth_txd3. However, I have no scope to fully confirm this assumption.
The vendor u-boot sources for Odroid-C1 use the following Ethernet
pinmux configuration:
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f);
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000);
This translates to the following pin groups in the mainline kernel:
- register 6 bit 0: eth_rxd1 (DIF_0_P)
- register 6 bit 1: eth_rxd0 (DIF_0_N)
- register 6 bit 2: eth_rx_dv (DIF_1_P)
- register 6 bit 3: eth_rx_clk (DIF_1_N)
- register 6 bit 6: eth_tx_en (DIF_3_P)
- register 6 bit 8: eth_ref_clk (DIF_3_N)
- register 6 bit 9: eth_mdc (DIF_4_P)
- register 6 bit 10: eth_mdio_en (DIF_4_N)
- register 6 bit 11: eth_tx_clk (GPIOH_9)
- register 6 bit 12: eth_txd2 (GPIOH_8)
- register 6 bit 13: eth_txd3 (GPIOH_7)
- register 7 bit 20: eth_txd0_0 (GPIOH_6)
- register 7 bit 21: eth_txd1_0 (GPIOH_5)
- register 7 bit 22: eth_rxd3 (DIF_2_P)
- register 7 bit 23: eth_rxd2 (DIF_2_N)
Drop the eth_txd0_1 and eth_txd1_1 groups from eth_rgmii_pins to fix the
Ethernet transmit performance on Odroid-C1. Also add the eth_rxd2 and
eth_rxd3 groups so we don't rely on the bootloader to set them up.
iperf3 statistics before this change:
- transmitting from Odroid-C1: 741 Mbits/sec (0 retries)
- receiving on Odroid-C1: 199 Mbits/sec (1713 retries)
iperf3 statistics after this change:
- transmitting from Odroid-C1: 667 Mbits/sec (0 retries)
- receiving on Odroid-C1: 750 Mbits/sec (0 retries)
Fixes: b96446541d8390 ("ARM: dts: meson8b: extend ethernet controller description")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Emiliano Ingrassia <ingrassia@epigenesys.com>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Reviewed-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit de9c0d49d85dc563549972edc5589d195cd5e859 ]
While building arm32 allyesconfig, I ran into the following errors:
arch/arm/lib/xor-neon.c:17:2: error: You should compile this file with
'-mfloat-abi=softfp -mfpu=neon'
In file included from lib/raid6/neon1.c:27:
/home/nathan/cbl/prebuilt/lib/clang/8.0.0/include/arm_neon.h:28:2:
error: "NEON support not enabled"
Building V=1 showed NEON_FLAGS getting passed along to Clang but
__ARM_NEON__ was not getting defined. Ultimately, it boils down to Clang
only defining __ARM_NEON__ when targeting armv7, rather than armv6k,
which is the '-march' value for allyesconfig.
>From lib/Basic/Targets/ARM.cpp in the Clang source:
// This only gets set when Neon instructions are actually available, unlike
// the VFP define, hence the soft float and arch check. This is subtly
// different from gcc, we follow the intent which was that it should be set
// when Neon instructions are actually available.
if ((FPU & NeonFPU) && !SoftFloat && ArchVersion >= 7) {
Builder.defineMacro("__ARM_NEON", "1");
Builder.defineMacro("__ARM_NEON__");
// current AArch32 NEON implementations do not support double-precision
// floating-point even when it is present in VFP.
Builder.defineMacro("__ARM_NEON_FP",
"0x" + Twine::utohexstr(HW_FP & ~HW_FP_DP));
}
Ard Biesheuvel recommended explicitly adding '-march=armv7-a' at the
beginning of the NEON_FLAGS definitions so that __ARM_NEON__ always gets
definined by Clang. This doesn't functionally change anything because
that code will only run where NEON is supported, which is implicitly
armv7.
Link: https://github.com/ClangBuiltLinux/linux/issues/287
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5c418dc789a3898717ebf2caa5716ba91a7150b2 ]
The following commit:
a893ea15d764 ("tpm: move tpm_chip definition to include/linux/tpm.h")
introduced a build error when both IMA and EFI are enabled:
In file included from ../security/integrity/ima/ima_fs.c:30:
../security/integrity/ima/ima.h:176:7: error: redeclaration of enumerator "NONE"
What happens is that both headers (ima.h and efi.h) defines the same
'NONE' constant, and it broke when they started getting included from
the same file:
Rework to prefix the EFI enum with 'EFI_*'.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20190215165551.12220-2-ard.biesheuvel@linaro.org
[ Cleaned up the changelog a bit. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aa7150ba378650d0e9d84b8e4d805946965a5926 ]
The recent rework of PCI kconfig symbols exposed an existing bug in
the CURRITUCK kconfig logic.
It selects PPC4xx_PCI_EXPRESS which depends on PCI, but PCI is user
selectable and might be disabled, leading to a warning:
WARNING: unmet direct dependencies detected for PPC4xx_PCI_EXPRESS
Depends on [n]: PCI [=n] && 4xx [=y]
Selected by [y]:
- CURRITUCK [=y] && PPC_47x [=y]
Prior to commit eb01d42a7778 ("PCI: consolidate PCI config entry in
drivers/pci") PCI was enabled by default for currituck_defconfig so we
didn't see the warning. The bad logic was still there, it just
required someone disabling PCI in their .config to hit it.
Fix it by forcing PCI on for CURRITUCK, which seems was always the
expectation anyway.
Fixes: eb01d42a7778 ("PCI: consolidate PCI config entry in drivers/pci")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5330367fa300742a97e20e953b1f77f48392faae ]
After we ALIGN up the address we need to make sure we didn't overflow
and resulted in zero address. In that case, we need to make sure that
the returned address is greater than mmap_min_addr.
This fixes selftest va_128TBswitch --run-hugetlb reporting failures when
run as non root user for
mmap(-1, MAP_HUGETLB)
The bug is that a non-root user requesting address -1 will be given address 0
which will then fail, whereas they should have been given something else that
would have succeeded.
We also avoid the first mmap(-1, MAP_HUGETLB) returning NULL address as mmap address
with this change. So we think this is not a security issue, because it only affects
whether we choose an address below mmap_min_addr, not whether we
actually allow that address to be mapped. ie. there are existing capability
checks to prevent a user mapping below mmap_min_addr and those will still be
honoured even without this fix.
Fixes: 484837601d4d ("powerpc/mm: Add radix support for hugetlb")
Reviewed-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b7e8c9397cd4efe6567d2728f091f1b728025533 ]
Use unified assembler syntax (UAL) in inline assembler. Divided
syntax is considered deprecated. This will also allow to build
the kernel using LLVM's integrated assembler.
When compiling non-Thumb2 GCC always emits a ".syntax divided"
at the beginning of the inline assembly which makes the
assembler fail. Since GCC 5 there is the -masm-syntax-unified
GCC option which make GCC assume unified syntax asm and hence
emits ".syntax unified" even in ARM mode. However, the option
is broken since GCC version 6 (see GCC PR88648 [1]). Work
around by adding ".syntax unified" as part of the inline
assembly.
[0] https://gcc.gnu.org/onlinedocs/gcc/ARM-Options.html#index-masm-syntax-unified
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=88648
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 74ffe79ae538283bbf7c155e62339f1e5c87b55a ]
Mostly unwind is done with irqs enabled however SLUB may call it with
irqs disabled while creating a new SLUB cache.
I had system freeze while loading a module which called
kmem_cache_create() on init. That means SLUB's __slab_alloc() disabled
interrupts and then
->new_slab_objects()
->new_slab()
->setup_object()
->setup_object_debug()
->init_tracking()
->set_track()
->save_stack_trace()
->save_stack_trace_tsk()
->walk_stackframe()
->unwind_frame()
->unwind_find_idx()
=>spin_lock_irqsave(&unwind_lock);
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e7140639b1de65bba435a6bd772d134901141f86 ]
When building with -Wsometimes-uninitialized, Clang warns:
arch/powerpc/xmon/ppc-dis.c:157:7: warning: variable 'opcode' is used
uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
if (cpu_has_feature(CPU_FTRS_POWER9))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/powerpc/xmon/ppc-dis.c:167:7: note: uninitialized use occurs here
if (opcode == NULL)
^~~~~~
arch/powerpc/xmon/ppc-dis.c:157:3: note: remove the 'if' if its
condition is always true
if (cpu_has_feature(CPU_FTRS_POWER9))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/powerpc/xmon/ppc-dis.c:132:38: note: initialize the variable
'opcode' to silence this warning
const struct powerpc_opcode *opcode;
^
= NULL
1 warning generated.
This warning seems to make no sense on the surface because opcode is set
to NULL right below this statement. However, there is a comma instead of
semicolon to end the dialect assignment, meaning that the opcode
assignment only happens in the if statement. Properly terminate that
line so that Clang no longer warns.
Fixes: 5b102782c7f4 ("powerpc/xmon: Enable disassembly files (compilation changes)")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 11f5acce2fa43b015a8120fa7620fa4efd0a2952 ]
We store 2 multilevel tables in iommu_table - one for the hardware and
one with the corresponding userspace addresses. Before allocating
the tables, the iommu_table_group_ops::get_table_size() hook returns
the combined size of the two and VFIO SPAPR TCE IOMMU driver adjusts
the locked_vm counter correctly. When the table is actually allocated,
the amount of allocated memory is stored in iommu_table::it_allocated_size
and used to decrement the locked_vm counter when we release the memory
used by the table; .get_table_size() and .create_table() calculate it
independently but the result is expected to be the same.
However the allocator does not add the userspace table size to
.it_allocated_size so when we destroy the table because of VFIO PCI
unplug (i.e. VFIO container is gone but the userspace keeps running),
we decrement locked_vm by just a half of size of memory we are
releasing.
To make things worse, since we enabled on-demand allocation of
indirect levels, it_allocated_size contains only the amount of memory
actually allocated at the table creation time which can just be a
fraction. It is not a problem with incrementing locked_vm (as
get_table_size() value is used) but it is with decrementing.
As the result, we leak locked_vm and may not be able to allocate more
IOMMU tables after few iterations of hotplug/unplug.
This sets it_allocated_size in the pnv_pci_ioda2_ops::create_table()
hook to what pnv_pci_ioda2_get_table_size() returns so from now on we
have a single place which calculates the maximum memory a table can
occupy. The original meaning of it_allocated_size is somewhat lost now
though.
We do not ditch it_allocated_size whatsoever here and we do not call
get_table_size() from vfio_iommu_spapr_tce.c when decrementing
locked_vm as we may have multiple IOMMU groups per container and even
though they all are supposed to have the same get_table_size()
implementation, there is a small chance for failure or confusion.
Fixes: 090bad39b237 ("powerpc/powernv: Add indirect levels to it_userspace")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bc8ff3ca6589d63c6d10f5ee8bed38f74851b469 ]
The descriptions of userspace memory access functions had minor issues
with formatting that made kernel-doc unable to properly detect the
function/macro names and the return value sections:
./arch/x86/include/asm/uaccess.h:80: info: Scanning doc for
./arch/x86/include/asm/uaccess.h:139: info: Scanning doc for
./arch/x86/include/asm/uaccess.h:231: info: Scanning doc for
./arch/x86/include/asm/uaccess.h:505: info: Scanning doc for
./arch/x86/include/asm/uaccess.h:530: info: Scanning doc for
./arch/x86/lib/usercopy_32.c:58: info: Scanning doc for
./arch/x86/lib/usercopy_32.c:69: warning: No description found for return
value of 'clear_user'
./arch/x86/lib/usercopy_32.c:78: info: Scanning doc for
./arch/x86/lib/usercopy_32.c:90: warning: No description found for return
value of '__clear_user'
Fix the formatting.
Link: http://lkml.kernel.org/r/1549549644-4903-3-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 179fb36abb097976997f50733d5b122a29158cba ]
After commit 68bb7bfb7985 ("X86/Hyper-V: Enable IPI enlightenments"),
kexec fails with a kernel panic:
kexec_core: Starting new kernel
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v3.0 03/02/2018
RIP: 0010:0xffffc9000001d000
Call Trace:
? __send_ipi_mask+0x1c6/0x2d0
? hv_send_ipi_mask_allbutself+0x6d/0xb0
? mp_save_irq+0x70/0x70
? __ioapic_read_entry+0x32/0x50
? ioapic_read_entry+0x39/0x50
? clear_IO_APIC_pin+0xb8/0x110
? native_stop_other_cpus+0x6e/0x170
? native_machine_shutdown+0x22/0x40
? kernel_kexec+0x136/0x156
That happens if hypercall based IPIs are used because the hypercall page is
reset very early upon kexec reboot, but kexec sends IPIs to stop CPUs,
which invokes the hypercall and dereferences the unusable page.
To fix his, reset hv_hypercall_pg to NULL before the page is reset to avoid
any misuse, IPI sending will fall back to the non hypercall based
method. This only happens on kexec / kdump so just setting the pointer to
NULL is good enough.
Fixes: 68bb7bfb7985 ("X86/Hyper-V: Enable IPI enlightenments")
Signed-off-by: Kairui Song <kasong@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: devel@linuxdriverproject.org
Link: https://lkml.kernel.org/r/20190306111827.14131-1-kasong@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fc2b47b55f17fd996f7a01975ce1c33c2f2513f6 ]
It believe it is a bad idea to hardcode a specific compiler prefix
that may or may not be installed on a user's system. It is annoying
when testing features that should not require compilers at all.
For example, mrproper, headers_install, etc. should work without
any compiler.
They look like follows on my machine.
$ make ARCH=h8300 mrproper
./scripts/gcc-version.sh: line 26: h8300-unknown-linux-gcc: command not found
./scripts/gcc-version.sh: line 27: h8300-unknown-linux-gcc: command not found
make: h8300-unknown-linux-gcc: Command not found
make: h8300-unknown-linux-gcc: Command not found
[ a bunch of the same error messages continue ]
$ make ARCH=h8300 headers_install
./scripts/gcc-version.sh: line 26: h8300-unknown-linux-gcc: command not found
./scripts/gcc-version.sh: line 27: h8300-unknown-linux-gcc: command not found
make: h8300-unknown-linux-gcc: Command not found
HOSTCC scripts/basic/fixdep
make: h8300-unknown-linux-gcc: Command not found
WRAP arch/h8300/include/generated/uapi/asm/kvm_para.h
[ snip ]
The solution is to delete this line, or to use cc-cross-prefix like
some architectures do. I chose the latter as a moderate fixup.
I added an alternative 'h8300-linux-' because it is available at:
https://mirrors.edge.kernel.org/pub/tools/crosstool/files/bin/x86_64/8.1.0/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Add simplified partitions for BMC and alternate flash. Include these by
default in Witherspoon.
OpenBMC-Staging-Count: 1
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Adriana Kobylak <anoo@us.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
OpenBMC-Staging-Count: 1
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Enable the video engine and add it's optional reserved memory region.
Use 32MB for the reserved memory since the video engine could need up to
two 1920x1200@32bpp source buffers.
Source buffers: 2 * 1920 * 1200 * 4 = 18432000 bytes
In addition, the V4L2 subsystem will allocate any number of compression
buffers, each at most 1/8th the size of the source buffer.
OpenBMC-Staging-Count: 1
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Enable the video engine and add it's optional reserved memory region.
Use 32MB for the reserved memory since the video engine could need up to
two 1920x1200@32bpp source buffers.
Source buffers: 2 * 1920 * 1200 * 4 = 18432000 bytes
In addition, the V4L2 subsystem will allocate any number of compression
buffers, each at most 1/8th the size of the source buffer.
OpenBMC-Staging-Count: 1
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Add a node to describe the video engine on the AST2500.
OpenBMC-Staging-Count: 1
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This is the 5.0.6 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
commit 45def77ebf79e2e8942b89ed79294d97ce914fa0 upstream.
Most (all?) x86 platforms provide a port IO based reset mechanism, e.g.
OUT 92h or CF9h. Userspace may emulate said mechanism, i.e. reset a
vCPU in response to KVM_EXIT_IO, without explicitly announcing to KVM
that it is doing a reset, e.g. Qemu jams vCPU state and resumes running.
To avoid corruping %rip after such a reset, commit 0967b7bf1c22 ("KVM:
Skip pio instruction when it is emulated, not executed") changed the
behavior of PIO handlers, i.e. today's "fast" PIO handling to skip the
instruction prior to exiting to userspace. Full emulation doesn't need
such tricks becase re-emulating the instruction will naturally handle
%rip being changed to point at the reset vector.
Updating %rip prior to executing to userspace has several drawbacks:
- Userspace sees the wrong %rip on the exit, e.g. if PIO emulation
fails it will likely yell about the wrong address.
- Single step exits to userspace for are effectively dropped as
KVM_EXIT_DEBUG is overwritten with KVM_EXIT_IO.
- Behavior of PIO emulation is different depending on whether it
goes down the fast path or the slow path.
Rather than skip the PIO instruction before exiting to userspace,
snapshot the linear %rip and cancel PIO completion if the current
value does not match the snapshot. For a 64-bit vCPU, i.e. the most
common scenario, the snapshot and comparison has negligible overhead
as VMCS.GUEST_RIP will be cached regardless, i.e. there is no extra
VMREAD in this case.
All other alternatives to snapshotting the linear %rip that don't
rely on an explicit reset announcenment suffer from one corner case
or another. For example, canceling PIO completion on any write to
%rip fails if userspace does a save/restore of %rip, and attempting to
avoid that issue by canceling PIO only if %rip changed then fails if PIO
collides with the reset %rip. Attempting to zero in on the exact reset
vector won't work for APs, which means adding more hooks such as the
vCPU's MP_STATE, and so on and so forth.
Checking for a linear %rip match technically suffers from corner cases,
e.g. userspace could theoretically rewrite the underlying code page and
expect a different instruction to execute, or the guest hardcodes a PIO
reset at 0xfffffff0, but those are far, far outside of what can be
considered normal operation.
Fixes: 432baf60eee3 ("KVM: VMX: use kvm_fast_pio_in for handling IN I/O")
Cc: <stable@vger.kernel.org>
Reported-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
