| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
To collect the CPU registers of the crashed system allocated a single
page with memblock_alloc_base and use it as a copy buffer. Replace the
stop-and-store-status sigp with a store-status-at-address sigp in
smp_save_dump_cpus() and smp_store_status(). In both cases the target
CPU is already stopped and store-status-at-address avoids the detour
via the absolute zero page.
For kexec simplify s390_reset_system and call store_status() before
the prefix register of the boot CPU has been set to zero. Use STPX
to store the prefix register and remove dump_prefix_page.
Acked-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Replace the SAVE_AREA_BASE offset calculations in reipl.S with the
assembler constant for the location of each register status area.
Use __LC_FPREGS_SAVE_AREA instead of SAVE_AREA_BASE in the three
remaining code locations and remove the definition of SAVE_AREA_BASE.
Acked-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The s390 architecture can store the CPU registers of the crashed system
after the kdump kernel has been started and this is the preferred way.
Remove the remaining code fragments that deal with storing CPU registers
while the crashed system is still active.
Acked-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The multi-threading facility is introduced with the z13 processor family.
This patch adds code to detect the multi-threading facility. With the
facility enabled each core will surface multiple hardware threads to the
system. Each hardware threads looks like a normal CPU to the operating
system with all its registers and properties.
The SCLP interface reports the SMT topology indirectly via the maximum
thread id. Each reported CPU in the result of a read-scp-information
is a core representing a number of hardware threads.
To reflect the reduced CPU capacity if two hardware threads run on a
single core the MT utilization counter set is used to normalize the
raw cputime obtained by the CPU timer deltas. This scaled cputime is
reported via the taskstats interface. The normal /proc/stat numbers
are based on the raw cputime and are not affected by the normalization.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
With this patch for kdump the s390 vector registers are stored into the
prepared save areas in the old kernel and into the REGSET_VX_LOW and
REGSET_VX_HIGH ELF notes for /proc/vmcore in the new kernel.
The NT_S390_VXRS_LOW note contains the lower halves of the first 16 vector
registers 0-15. The higher halves are stored in the floating point register
ELF note. The NT_S390_VXRS_HIGH contains the full vector registers 16-31.
The kernel provides a save area for storing vector register in case of
machine checks. A pointer to this save are is stored in the CPU lowcore
at offset 0x11b0. This save area is also used to save the registers for
kdump. In case of a dumped crashed kdump those areas are used to extract
the registers of the production system.
The vector registers for remote CPUs are stored using the "store additional
status at address" SIGP. For the dump CPU the vector registers are stored
with the VSTM instruction.
With this patch also zfcpdump stores the vector registers.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Make various functions static, add declarations to header files to
fix a couple of sparse findings.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
For s390 the page table mapping for the crashkernel memory is removed to
protect the pre-loaded kdump kernel and ramdisk. Because the crashkernel
memory is not included in the page tables for suspend/resume it is not
included in the suspend image. Therefore after resume the resumed system
does no longer contain the pre-loaded kdump kernel and when kdump is
triggered it fails.
This patch adds a PM notifier that creates the page tables before suspend
is done and removes them for resume. This ensures that the kdump kernel
is included in the suspend image.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Move fill_cpu_elf_notes() prototype to header file.
This way we get compile errors if e.g. the number of function
parameters get changed.
Otherwise it's possible to change just the definition and everything
else still compiles fine, but the result is broken code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Returning -ENOSYS on kexec_load() is a bad idea since user space cannot
tell if the system call is not implmented or if it failed.
Use -EOPNOTSUPP in case somebody tries a kexec_load on a NSS image based
kernel instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
machine_crash_shutdown() was the only function in crash.c.
So move the function and delete one file.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Remove the file name from the comment at top of many files. In most
cases the file name was wrong anyway, so it's rather pointless.
Also unify the IBM copyright statement. We did have a lot of sightly
different statements and wanted to change them one after another
whenever a file gets touched. However that never happened. Instead
people start to take the old/"wrong" statements to use as a template
for new files.
So unify all of them in one go.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Currently the PSW restart handler and kexec are executed in real
mode with DAT=off. For kexec/kdump the function setup_regs() is
called that uses the per-cpu variable "crash_notes". Because
there are situations when the per-cpu implementation uses vmalloc
memory, calling setup_regs() in real mode can cause a program
check interrupt.
To fix that problem this patch changes the following:
* Ensure that diag308_reset() does not change PSW bits to real mode
* Enable DAT in __do_restart() after we switched to an online CPU
* Enable DAT in __machine_kexec() after we switched to the IPL CPU
* Call setup_regs() before we switch to real mode and call purgatory
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The crashkernel size for kdump can be reduced at runtime with the
sysfs file "/sys/kernel/kexec_crash_size". Currently those changes
do not update the OS info crashkernel information that is used
for stand-alone kdump. With this fix now also the OS info crashkernel
information is updated correctly.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Disintegrate asm/system.h for S390.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-s390@vger.kernel.org
|
|
Currently the following mechanisms are available to move active
Linux on System z instances between machines:
* z/VM 6.2 SSI (Single System Image)
* Suspend/resume
For moving Linux instances in this patch the term LGR (Linux Guest
Relocation) is used. Because such an operation is critical, it
should be detectable from Linux. With this patch for both, a live
system and a kernel dump, the information about LGRs is accessible.
To identify a guest, stsi and stfle data is used. A new function
lgr_info_log() compares the current data (lgr_info_cur) with the
last recorded one (lgr_info_last). In case the two data sets differ,
lgr_info_cur is logged to the "lgr" s390dbf.
The following trigger points call lgr_info_log():
* panic
* die
* kdump
* LGR timer
* PSW restart
* QDIO recovery
* resume
This patch also changes the s390dbf hex_ascii view. Now only printable ASCII
characters are shown.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Define struct pcpu and merge some of the NR_CPUS arrays into it, including
__cpu_logical_map, current_set and smp_cpu_state. Split smp related
functions to those operating on physical cpus and the functions operating
on a logical cpu number. Make the functions for physical cpus use a
pointer to a struct pcpu. This hides the knowledge about cpu addresses in
smp.c, entry[64].S and swsusp_asm64.S, thus remove the sigp.h header.
The PSW restart mechanism is used to start secondary cpus, calling a
function on an online cpu, calling a function on the ipl cpu, and for
the nmi signal. Replace the different assembler functions with a
single function restart_int_handler. The new entry point calls a function
whose pointer is stored in the lowcore of the target cpu and it can wait
for the source cpu to stop. This covers all existing use cases.
Overall the code is now simpler and there are ~380 lines less code.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Currently the vmalloc_start address (or better end of real memory) for s390x
is obtained by makedumpfile using vmlist.addr symbol, which is not correct.
The correct vmalloc_start address can be obtained using 'high_memory' symbol.
This patch adds the high_memory symbol to vmcoreinfo.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Split out addressing mode bits from PSW_BASE_BITS, rename PSW_BASE_BITS
to PSW_MASK_BASE, get rid of psw_user32_bits, remove unused function
enabled_wait(), introduce PSW_MASK_USER, and drop PSW_MASK_MERGE macros.
Change psw_kernel_bits / psw_user_bits to contain only the bits that
are always set in the respective mode.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This patch implements the crash_map_pages() function for s390.
KEXEC_CRASH_MEM_ALIGN is set to HPAGE_SIZE, in order to support
kernel mappings that use large pages. We also use HPAGE_SIZE alignment
for CONFIG_HUGETLB_PAGE=n in order to have the same 1 MiB alignment on
all s390 systems.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This patch provides the architecture specific part of the s390 kdump
support.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Disable ftrace during kexec. Same as on x86/powerpc.
ac4414e "powerpc/kdump: Disable ftrace during kexec".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Always reboot on logical cpu 0. This makes sure that the IPL cpu is
always the same and usually avoids strange numbering schemes between
physical and logical cpus.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
nss and kexec don't work together since kexec wants to write to the
read-only text section of the shared kernel image.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Let one master cpu kill all other cpus instead of sending an external
interrupt to all other cpus so they can kill themselves.
Simplifies reipl/shutdown functions a lot.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
In case of re-IPL and diag308 doesn't work we have to reset all devices
manually and wait synchronously that each reset finished.
This patch adds the necessary infrastucture and the first exploiter of it.
Subsystems that need to add a function that needs to be called at re-IPL
may register/unregister this function via
struct reset_call {
struct reset_call *next;
void (*fn)(void);
};
void register_reset_call(struct reset_call *reset);
void unregister_reset_call(struct reset_call *reset);
When the registered function get called the context is:
- all cpus beside the current one are stopped
- all machine checks and interrupts are disabled
- prefixing is disabled
- a default machine check handler is available for use
The registered functions may not take any locks are sleep.
For the common I/O layer part of this patch:
Introduce a reset_call css_reset that does the following:
- clear all subchannels
- perform a rchp on all channel paths and wait for the resulting
machine checks
This replaces the calls to clear_all_subchannels() and
cio_reset_channel_paths() for kexec and ccw reipl. reipl_ccw_dev() now
uses reipl_find_schid() to determine the subchannel id for a given
device id.
Also remove cio_reset_channel_paths() and friends since they are not
needed anymore.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
1. Multipath devices for which SetPGID is not supported are not handled well.
Use NOP ccws for path verification (sans path grouping) when SetPGID is not
supported.
2. Check for PGIDs already set with SensePGID on _all_ paths (not just the
first one) and try to find a common one. Moan if no common PGID can be
found (and use NOP verification). If no PGIDs have been set, use the css
global PGID (as before). (Rationale: SetPGID will get a command reject if
the PGID it tries to set does not match the already set PGID.)
3. Immediately before reboot, issue RESET CHANNEL PATH (rcp) on all chpids. This
will remove the old PGIDs. rcp will generate solicited CRWs which can be
savely ignored by the machine check handler (all other actions create
unsolicited CRWs).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Storage class should be before const
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Add missing smp_cpu_not_running define to avoid build warnings in the non smp
case.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Hugh Dickins <hugh@veritas.com>
Fix the broken atomic_cmpxchg primitive. Add atomic_sub_and_test,
atomic64_sub_return, atomic64_sub_and_test, atomic64_cmpxchg,
atomic64_add_unless and atomic64_inc_not_zero. Replace old style
atomic_compare_and_swap by atomic_cmpxchg. Shorten the whole header by
defining most primitives with the two inline functions atomic_add_return and
atomic_sub_return.
In addition this patch contains the s390 related fixes of Hugh's "mm: fill
arch atomic64 gaps" patch.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Disable pseudo page fault handling before starting the new kernel and try
to use diag308 to reset the machine.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
o Following patch provides purely cosmetic changes and corrects CodingStyle
guide lines related certain issues like below in kexec related files
o braces for one line "if" statements, "for" loops,
o more than 80 column wide lines,
o No space after "while", "for" and "switch" key words
o Changes:
o take-2: Removed the extra tab before "case" key words.
o take-3: Put operator at the end of line and space before "*/"
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add kexec support for s390 architecture.
From: Milton Miller <miltonm@bga.com>
- Fix passing of first argument to relocate_kernel assembly.
- Fix Kconfig description.
- Remove wrong comment and comments that describe obvious things.
- Allow only KEXEC_TYPE_DEFAULT as image type -> dump not supported.
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
