| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.10
A few fixes here and there to enable the build of some DT leftover, prevent
display issues or setup a proper muxing.
* tag 'sunxi-fixes-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sunxi: Change node name for pwrseq pin on Olinuxino-lime2-emmc
ARM: dts: sun8i: Support DTB build for NanoPi M1
ARM: dts: sun6i: hummingbird: Enable display engine again
ARM: dts: sun6i: Disable display pipeline by default
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.10, 2nd round:
- A couple of Nitrogen6 device tree fixes for audio codec probe
failure, which is caused by that pinctrl setting for codec clock
was not in the correct device node.
* tag 'imx-fixes-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-nitrogen6_som2: fix sgtl5000 pinctrl init
ARM: dts: imx6qdl-nitrogen6_max: fix sgtl5000 pinctrl init
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The node name for the power seq pin is mmc2@0 like the mmc2_pins_a one.
This makes the original node (mmc2_pins_a) scrapped out of the dtb and
result in a unusable eMMC if U-Boot didn't configured the pins to the
correct functions.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The commit 10efbf5f1633 ("ARM: dts: sun8i: Add dts file for NanoPi M1 SBC")
introduced NanoPi M1 board but it's missing in Allwinner H3 DTB build.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Now that we disable the display engine by default, we need to re-enable
it for the Hummingbird A31, which already had its display pipeline
enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
While we now support the internal display pipeline found on sun6i, it
is possible that we are unable to enable the display for some boards,
due to a lack of drivers for the panels or bridges found on them. If
the display pipeline is enabled, the driver will try to enable, and
possibly screw up the simple framebuffer U-boot had configured.
Disable the display pipeline by default.
Fixes: 6d0e5b70be13 ("ARM: dts: sun6i: Add device nodes for first
display pipeline")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Tree-wide replacement was done by commit 2ef7d5f342c1 ("ARM, ARM64:
dts: drop "arm,amba-bus" in favor of "simple-bus"), then the 2nd
round by commit 15b7cc78f095 ("arm64: dts: drop "arm,amba-bus" in
favor of "simple-bus" part 2").
Here, some new users have appeared for Linux v4.10-rc1. Eliminate
them now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Since the codec is probed first, the pinctrl node should be
under the codec node.
The codec init was working for this board since U-Boot was
already setting GPIO_0 as CLKO1 but better fix it anyway.
Fixes: 3faa1bb2e89c ("ARM: dts: imx: add Boundary Devices Nitrogen6_SOM2 support")
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch fixes the following error:
sgtl5000 0-000a: Error reading chip id -6
imx-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered
imx-sgtl5000 sound: snd_soc_register_card failed (-517)
The problem was that the pinctrl group was linked to the sound driver
instead of the codec node. Since the codec is probed first, the sys_mclk
was missing and it would therefore fail to initialize.
Fixes: b32e700256bc ("ARM: dts: imx: add Boundary Devices Nitrogen6_Max board")
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
Pull "DaVinci fixes for v4.10" from Sekhar Nori:
This pull request contains fixes for the following issues
1) Fix two instances of infinite loop occurring in
clock list for DA850. This fixes kernel hangs in some
instances and so have been marked for stable kernel.
2) Fix for sleeping function called from atomic context
with USB 2.0 clock management code introduced in v4.10
merge window.
* tag 'davinci-fixes-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da8xx: Fix sleeping function called from invalid context
ARM: davinci: Make __clk_{enable,disable} functions public
ARM: davinci: da850: don't add emac clock to lookup table twice
ARM: davinci: da850: fix infinite loop in clk_set_rate()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into fixes
Pull "ARMv7 VExpress fixes for v4.10" from Sudeep Holla:
A simple fix to extend GICv2 CPU interface registers from 4K to 8K
on VExpress TC1 and TC2 platforms in order to support split priority
drop and interrupt deactivation.
* tag 'vexpress-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: Support GICC_DIR operations
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "i.MX fixes for 4.10" from Shawn Guo:
- A format fix for vf610-zii-dev-rev-b.dts, which has a very odd line
due to misses a newline.
- A fix to imx-weim bus error seen on board which doesn't actually use
the bus.
- A fix for imx6qdl-nitrogen6x board which has conflicting usage of
pad NANDF_CS2.
- A cleanup on i.MX1 machine to remove .map_io callback, which also
fixes a compiling error for NOMMU build.
- Fix AVIC base address in i.MX31 device tree source. The problem was
shadowed by the AVIC driver, which takes the correct base address
from a SoC specific header file.
* tag 'imx-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6: Disable "weim" node in the dtsi files
ARM: i.MX: remove map_io callback
ARM: dts: vf610-zii-dev-rev-b: Add missing newline
ARM: dts: imx6qdl-nitrogen6x: remove duplicate iomux entry
ARM: dts: imx31: fix AVIC base address
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into fixes
Pull "Qualcomm ARM DTS Fixes for v4.10-rc2" from Andy Gross:
* Add SCM clock for APQ8064 to fix boot failures
* tag 'qcom-arm-fixes-for-4.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: dts: qcom: apq8064: Add missing scm clock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Pull "omap fixes for v4.10-rc cycle" from Tony Lindgren:
Fist set of fixes for omaps for v4.10-rc cycle, mostly
to deal with various regressions noticed during the merge
window and to fix various device tree configurations for
boards. Also included is removal of mach-omap2/gpio.c that
is now dead code with device tree based booting that should
be OK for the early -rc cycle:
- A series of fixes to add empty chosen node to fix regressions
caused for bootloaders that don't create chosen node as the
decompressor needs the chosen node to merge command line and
ATAGs into it
- Fix missing logicpd-som-lv-37xx-devkit.dtb entry in Makefile
- Fix regression for am437x timers
- Fix wrong strcat for non-NULL terminated string
- A series of changes to fix tps65217 interrupts to not use
defines as we don't do that for interrupts
- Two patches to fix USB VBUS detection on am57xx-idk and force it
to peripheral mode until dwc3 role detection is working
- Add missing dra72-evm-tps65917 missing voltage supplies
accidentally left out of an earlier patch
- Fix n900 eMMC detection when booted on qemu
- Remove unwanted pr_err on failed memory allocation for
prm_common.c
- Remove legacy mach-omap2/gpio.c that now is dead code
since we boot mach-omap2 in device tree only mode
- Fix am572x-idk pcie1 by adding the missing gpio reset pin
* tag 'omap-for-v4.10/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (23 commits)
ARM: dts: am572x-idk: Add gpios property to control PCIE_RESETn
ARM: OMAP2+: PRM: Delete an error message for a failed memory allocation
ARM: dts: n900: Mark eMMC slot with no-sdio and no-sd flags
ARM: dts: dra72-evm-tps65917: Add voltage supplies to usb_phy, mmc, dss
ARM: dts: am57xx-idk: Put USB2 port in peripheral mode
ARM: dts: am57xx-idk: Support VBUS detection on USB2 port
dt-bindings: input: Specify the interrupt number of TPS65217 power button
dt-bindings: power/supply: Update TPS65217 properties
dt-bindings: mfd: Remove TPS65217 interrupts
ARM: dts: am335x: Fix the interrupt name of TPS65217
ARM: omap2+: fixing wrong strcat for Non-NULL terminated string
ARM: omap2+: am437x: rollback to use omap3_gptimer_timer_init()
ARM: dts: omap3: Add DTS for Logic PD SOM-LV 37xx Dev Kit
ARM: dts: dra7: Add an empty chosen node to top level DTSI
ARM: dts: dm816x: Add an empty chosen node to top level DTSI
ARM: dts: dm814x: Add an empty chosen node to top level DTSI
ARM: dts: am4372: Add an empty chosen node to top level DTSI
ARM: dts: am33xx: Add an empty chosen node to top level DTSI
ARM: dts: omap5: Add an empty chosen node to top level DTSI
ARM: dts: omap4: Add an empty chosen node to top level DTSI
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into fixes
Samsung mach/soc update for v4.10:
1. Minor cleanup in smp_operations.
2. Another step in switching s3c24xx to new DMA API.
3. Drop fixed requirement for HZ=200 on Samsung platforms.
* tag 'samsung-soc-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: Drop fixed 200 Hz timer requirement from Samsung platforms
ARM: S3C24XX: Add DMA slave maps for remaining s3c24xx SoCs
ARM: EXYNOS: Remove smp_init_cpus hook from platsmp.c
|
|
Commit 1be81ea5860744520 ("ARM: dts: imx6: Add imx-weim parameters to
dtsi's") causes the following probe error when the weim node is not
present on the board dts (such as imx6q-sabresd):
imx-weim 21b8000.weim: Invalid 'ranges' configuration
imx-weim: probe of 21b8000.weim failed with error -22
There is no need to always enable the "weim" node on mx6. Do the same
as in the other i.MX dtsi files where "weim" is disabled and only gets
enabled on a per dts basis.
All the imx6 weim dts users explicitily provide 'status = "okay"', so
this change has no impact on current imx6 weim users.
If a board does not use the weim driver it will not describe its 'ranges'
property, so simply disable the 'weim' node in the imx6 dtsi files to
avoid such probe error message.
Fixes: 1be81ea5860744520 ("ARM: dts: imx6: Add imx-weim parameters to dtsi's")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
As per the device tree binding the apq8064 scm node requires the core
clock to be specified, so add this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Everytime the usb20 phy is enabled, there is a
"sleeping function called from invalid context" BUG.
In addition, there is a recursive locking happening
because of the recurse call to clk_enable().
clk_enable() from arch/arm/mach-davinci/clock.c uses
spin_lock_irqsave() before to invoke the callback
usb20_phy_clk_enable(). usb20_phy_clk_enable() uses
clk_get() and clk_enable_prepapre() which may sleep.
Replace clk_prepare_enable() by davinci_clk_enable().
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Suggested-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: minor commit description adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
In some cases, there is a need to enable a clock as part of
clock enable callback of a different clock. For example, USB
2.0 PHY clock enable requires USB 2.0 clock to be enabled.
In this case, it is safe to instead call __clk_enable()
since the clock framework lock is already taken. Calling
clk_enable() causes recursive locking error.
A similar case arises in the clock disable path.
To enable such usage, make __clk_{enable,disable} functions
publicly available outside of clock.c. Also, call them
davinci_clk_{enable|disable} now to be consistent with how
other davinci-specific clock functions are named.
Note that these functions are not exported to drivers. They
are meant for usage in platform specific clock management
code.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Suggested-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Similarly to the aemif clock - this screws up the linked list of clock
children. Create a separate clock for mdio inheriting the rate from
emac_clk.
Cc: <stable@vger.kernel.org> # 3.12.x-
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: add a comment over mdio_clk to explaing its existence +
commit headline updates]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
The aemif clock is added twice to the lookup table in da850.c. This
breaks the children list of pll0_sysclk3 as we're using the same list
links in struct clk. When calling clk_set_rate(), we get stuck in
propagate_rate().
Create a separate clock for nand, inheriting the rate of the aemif
clock and retrieve it in the davinci_nand module.
Cc: <stable@vger.kernel.org> # 4.9.x
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
There is no need to define map_io only for debug_ll_io_init() since it
is already called in devicemaps_init() if map_io is NULL.
Apart from that, for NOMMU build debug_ll_io_init() is a nop which
leads to following error:
CC arch/arm/mach-imx/mach-imx1.o
arch/arm/mach-imx/mach-imx1.c:40:13: error: 'debug_ll_io_init' undeclared here (not in a function)
.map_io = debug_ll_io_init,
^
make[1]: *** [arch/arm/mach-imx/mach-imx1.o] Error 1
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Found while reviewing Marvell dsa bindings usage.
Fixes: f283745b3caf ("arm: vf610: zii devel b: Add support for switch interrupts")
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The NANDF_CS2 pad is also part of the wlan-vmmcgrp iomux group.
Removing is from the usdhc2grp group avoids the following error:
imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_NANDF_CS2 already requested
by regulators:regulator@4; cannot claim for 2194000.usdhc
imx6q-pinctrl 20e0000.iomuxc: pin-187 (2194000.usdhc) status -22
imx6q-pinctrl 20e0000.iomuxc: could not request pin 187
(MX6Q_PAD_NANDF_CS2) from group usdhc2grp on device 20e0000.iomuxc
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX31 AVIC interrupt controller base address is at 0x68000000.
The problem was shadowed by the AVIC driver, which takes the correct
base address from a SoC specific header file.
Fixes: d2a37b3d91f4 ("ARM i.MX31: Add devicetree support")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add 'gpios' property to pcie1 dt node and populate it with
GPIO3_23 in order to drive PCIE_RESETn high.
This gets PCIe cards to be detected in AM572X IDK board.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The GICv2 CPU interface registers span across 8K, not 4K as indicated in
the DT. Only the GICC_DIR register is located after the initial 4K
boundary, leaving a functional system but without support for separately
EOI'ing and deactivating interrupts.
After this change the system supports split priority drop and interrupt
deactivation.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
[sudeep.holla@arm.com: included same fix for tc1 platform too]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
|
|
Omit an extra message for a memory allocation failure in this function.
Link: http://events.linuxfoundation.org/sites/events/files/slides/LCJ16-Refactor_Strings-WSang_0.pdf
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Trying to initialize eMMC slot as SDIO or SD cause failure in n900 port of
qemu. eMMC itself is not detected and is not working.
Real Nokia N900 harware does not have this problem. As eMMC is really not
SDIO or SD based such change is harmless and will fix support for qemu.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 5d080aa30681 ("ARM: dts: dra72: Add separate dtsi for tps65917")
added a separate dtsi for dra72-evm-tps65917 moving all the voltage supplies
to this file. But it missed adding voltage supplies to usb_phy, mmc,
dss and deleted from dra72-evm-common.dtsi. Adding the voltage supply
phandles to these nodes in dra72-evm-tps65917.dtsi
Fixes: 5d080aa30681 ("ARM: dts: dra72: Add separate dtsi for tps65917")
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
USB2 port can be operated in dual-role mode but till we
have dual-role support in dwc3 driver let's limit this
port to peripheral mode.
If we don't do so it defaults to host mode. USB1 port
is meant for host only operation and we don't want
both ports in host only mode.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
VBUS detection is available on the board via the palmas PMIC.
Use extcon-palmas driver instead of extcon-gpio-usb driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Interrupt numbers are from the datasheet, so no need to keep them in
the ABI. Use the number in the DT file.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use 'interrupt-names' for getting the charger interrupt number.
Fixes: 1934e89a769b ("ARM: dts: am335x: Add the charger interrupt")
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Issue caught with static analysis tool:
"Dangerous usage of 'name' (strncpy doesn't always 0-terminate it)"
Use strlcpy _includes_ the NUL terminator, and strlcat() which ensures
that it won't overflow the buffer.
Reported-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
CC: Russell King <linux@armlinux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The commit 55ee7017ee31 ("arm: omap2: board-generic: use
omap4_local_timer_init for AM437x") unintentionally changes the
clocksource devices for AM437x from OMAP GP Timer to SyncTimer32K.
Unfortunately, the SyncTimer32K is starving from frequency deviation
as mentioned in commit 5b5c01359152 ("ARM: OMAP2+: AM43x: Use gptimer
as clocksource") and, as reported by Franklin [1], even its monotonic
nature is under question (most probably there is a HW issue, but it's
still under investigation).
Taking into account above facts It's reasonable to rollback to the use
of omap3_gptimer_timer_init().
[1] http://www.spinics.net/lists/linux-omap/msg127425.html
Fixes: 55ee7017ee31 ("arm: omap2: board-generic: use
omap4_local_timer_init for AM437x")
Reported-by: Cooper Jr., Franklin <fcooper@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fixes: ("ab8dd3aed011 ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")
This adds the dts file into the Makefile. This should have been included in
the original patch.
V2: Update patch description - same source code
V1: Original patch
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 55871eb6e2cc ("ARM: dts: dra7: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 55871eb6e2cc ("ARM: dts: dra7: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 06bfb9c19957 ("ARM: dts: dm816x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 06bfb9c19957 ("ARM: dts: dm816x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 76155b378c59 ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 76155b378c59 ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 75813028bbd7 ("ARM: dts: am4372: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 75813028bbd7 ("ARM: dts: am4372: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit f8bf01611c99 ("ARM: dts: am33xx: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: f8bf01611c99 ("ARM: dts: am33xx: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 76a8548ea987 ("ARM: dts: omap5: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 76a8548ea987 ("ARM: dts: omap5: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit da6269e7e3dd ("ARM: dts: omap4: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: da6269e7e3dd ("ARM: dts: omap4: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 008a2ebcd677 ("ARM: dts: omap3: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 008a2ebcd677 ("ARM: dts: omap3: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit d1f3156fc8c7 ("ARM: dts: omap2: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: d1f3156fc8c7 ("ARM: dts: omap2: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer type cleanups from Thomas Gleixner:
"This series does a tree wide cleanup of types related to
timers/timekeeping.
- Get rid of cycles_t and use a plain u64. The type is not really
helpful and caused more confusion than clarity
- Get rid of the ktime union. The union has become useless as we use
the scalar nanoseconds storage unconditionally now. The 32bit
timespec alike storage got removed due to the Y2038 limitations
some time ago.
That leaves the odd union access around for no reason. Clean it up.
Both changes have been done with coccinelle and a small amount of
manual mopping up"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Get rid of ktime_equal()
ktime: Cleanup ktime_set() usage
ktime: Get rid of the union
clocksource: Use a plain u64 instead of cycle_t
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull SMP hotplug notifier removal from Thomas Gleixner:
"This is the final cleanup of the hotplug notifier infrastructure. The
series has been reintgrated in the last two days because there came a
new driver using the old infrastructure via the SCSI tree.
Summary:
- convert the last leftover drivers utilizing notifiers
- fixup for a completely broken hotplug user
- prevent setup of already used states
- removal of the notifiers
- treewide cleanup of hotplug state names
- consolidation of state space
There is a sphinx based documentation pending, but that needs review
from the documentation folks"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/armada-xp: Consolidate hotplug state space
irqchip/gic: Consolidate hotplug state space
coresight/etm3/4x: Consolidate hotplug state space
cpu/hotplug: Cleanup state names
cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
staging/lustre/libcfs: Convert to hotplug state machine
scsi/bnx2i: Convert to hotplug state machine
scsi/bnx2fc: Convert to hotplug state machine
cpu/hotplug: Prevent overwriting of callbacks
x86/msr: Remove bogus cleanup from the error path
bus: arm-ccn: Prevent hotplug callback leak
perf/x86/intel/cstate: Prevent hotplug callback leak
ARM/imx/mmcd: Fix broken cpu hotplug handling
scsi: qedi: Convert to hotplug state machine
|
|
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
|
