| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Mainline Commit b74c2b21e1551018af53ee6c1efc051dfce2d788 added the pinmux
settings for mmc1, however this pin (0x9a0) is routed to P9_42 on the cape
header. Thus any BeagleBone cape that utilizes P9_42 triggers mmc0's Write
Protect.
Fixes: b74c2b21e155 ("ARM: dts: am33xx: Add pinmux data for mmc1 in
am335x-evm, evmsk and beaglebone")
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Faiz Abbas <faiz_abbas@ti.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
am335x-evm, am335x-evmsk and am335x-beaglebone are currently relying on
pinmux set by the bootloader to set the correct value for mmc1. Fix
this by adding pinmux data for the same in kernel.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add clkctrl nodes for AM33xx SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The interrupt for power button is static data that comes from the
datasheet, there is no reason to need to define this value on every
board so seams reasonable put this information into the common tps65217
file.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The interrupt specifiers for USB and AC charger input are static data that
comes from the datasheet, there is no reason to need to define these values
on every board so seem reasonable put this information into the common
tps65217 file.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree changes for omaps for v4.11 merge window. These
changes add earlycon stdout-path propety for the SoCs so far
tested with it. The other changes are addition of BeagleBone
green and making WLAN work on BeagleBone black wireless and
green wireless. The rest of the changes are the usual enabling
features on various devices:
- Enable devices on am335x-sl50
- Changes to dra7-evm boards to enable enable irqs for dp83867
eth phys, add pinmux configuration for mmc, remov erratum
i869 pinmux configurations, disable NAND support because of
pin conflict, add pcf8575 used for lcd
- Remove NAND partition table for omap3-igep
- Configure USB Ethernet MAC from device tree for beagleboard
xm, pandaboard, omap5-uevm and igepv5
- Configure am335x-chilisom to wake from RTC-only state
- Update Nanobone for external FRAM chip
- Clean up n900 dts
- Update am335x-phycore and am335x-wega for various devices
- Changes for am57xx-beagle-x15 to implement rgmii2 errata
* tag 'omap-for-v4.11/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (35 commits)
ARM: dts: dra72/1-evm: add pcf8575 used for lcd
ARM: dts: dra7xx: Add stdout-path property
ARM: dts: am57xx: Add stdout-path property
ARM: dts: am43xx: Add stdout-path property
ARM: dts: am33xx: Add stdout-path property
ARM: dts: am335x-sl50: Enable the Ambient Light Sensor.
ARM: dts: am335x-sl50: Enable the MCP23017 GPIO Expander.
ARM: dts: am335x-sl50: Enable BQ32000 Real Time Clock.
ARM: dts: am335x-sl50: Enable SPI0 interface and Flash Memory.
ARM: dts: am335x-sl50: Enable UART1.
ARM: dts: am335x-sl50: Remove I2C1 node.
ARM: dts: omap3-igep: Remove NAND partition table
ARM: dts: am57xx-beagle-x15: implement errata "Ethernet RGMII2 Limited to 10/100 Mbps"
ARM: dts: am335x-phycore-som: Remove partition tables
ARM: dts: dra72-evm-revc: enable irqs for dp83867 eth phys
ARM: dts: Configure BeagleBone peripheral USB VBUS irq
ARM: dts: omap5-igep0050: Allow bootloader to configure USB Ethernet MAC
ARM: dts: omap5-uevm: Allow bootloader to configure USB Ethernet MAC
ARM: dts: pandaboard: Allow bootloader to configure USB Ethernet MAC
ARM: omap3: beagleboard-xm: dt: Add ethernet to the device tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This prevents having to poll peripheral USB port cable status.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Interrupt numbers are from the datasheet, so no need to keep them in
the ABI. Use the number in the DT file.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use 'interrupt-names' for getting the charger interrupt number.
Fixes: 1934e89a769b ("ARM: dts: am335x: Add the charger interrupt")
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
rtc can either be supplied from internal 32k clock or external crystal
generated 32k clock. Internal clock is SoC specific and the external
clock is board dependent. Assigning the corresponding clocks.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This enables the power button driver gets corresponding IRQ number by
using platform_get_irq().
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This enables the charger driver gets corresponding IRQ number by using
platform_get_irq_byname() helper.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
AM335x bone based boards have the PMIC interrupt named NMI which is
connected to TPS65217 device. AM335x main interrupt controller provides it
and the number is 7.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes the following DTC warnings for many boards:
"Node /leds/led@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes the following DTC warnings for many boards:
"Node /fixedregulator@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This commit adds the stdout-path propety in /chosen for all Beaglebone
boards.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Currently am33xx.dtsi declares the MAC controller to have two
slave ports, on these boards we only use one, so set the slave
count to one. This eliminates a console error message when
the non-existent PHY is not detected.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Now that we are moving to OPPv2 bindings and able to add 1GHz OPP for
MPU, let's update the max MPU voltage range to align with the maximum
possible value allowed in the operating-points table, which is max
target voltage of 132500 uV + 2%.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This reverts commit 8e6ebfaa9b384088002baa10f7534efa73a0794e.
Without the patch reverted regulators will not work. This prevents
MMC to be working for example so the boards can not boot to
MMC rootfs.
Tested it on beaglebone white and bisect also points to the
reverted commit.
The issue can be also fixed by adding "regulator-compatible =" to all board
dts file for the regulators.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
remove tps65217.dtsi and adapt all boards, which
used it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
binding docs
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In AM335x the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Kevin Hilman:
"As usual, quite a few device-tree updates in ARM land. There was one
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS
RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill
SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33,
Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (462 commits)
ARM: hisi: revert changes from hisi/hip04-dt branch
ARM: nomadik: set proper compatible for accelerometer
ARM64: juno: add GPIO keys
ARM: at91/dt: sama5d4: fix dma conf for aes, sha and tdes nodes
ARM: dts: Introduce STM32F429 MCU
ARM: socfpga: dts: enable ethernet for Arria10 devkit
ARM: dts: k2l: fix the netcp range size
ARM: dts: k2e: fix the netcp range size
ARM: dts: k2hk: fix the netcp range size
ARM: dts: k2l-evm: Add device bindings for netcp driver
ARM: dts: k2e-evm: Add device bindings for netcp driver
ARM: dts: k2hk-evm: Add device bindings for netcp driver
ARM: BCM5301X: Add DT for Asus RT-AC87U
ARM: BCM5301X: add IRQ numbers for PCIe controller
ARM: BCM5301X: add NAND flash chip description
arm64: dts: Add dts files for Hisilicon Hi6220 SoC
clk: hi6220: Document devicetree bindings for hi6220 clock
arm64: hi6220: Document devicetree bindings for Hisilicon hi6220 SoC
ARM: at91/dt: sama5d4ek: mci0 uses slot 0
ARM: at91/dt: kizbox: fix mismatch LED PWM device
...
|
|
Avoid entering "RTC-only mode" at poweroff. It is unsupported by most
versions of BeagleBone, and risks hardware damage.
The damaging configuration is having system-power-controller
without ti,pmic-shutdown-controller.
Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Tested-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Johan Hovold <johan@kernel.org>
[Matthijs van Duin: added explanatory comments]
Signed-off-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Fixes: http://bugs.elinux.org/issues/143
Cc: stable@vger.kernel.org # v3.12+
[tony@atomide.com: updated comments with the hardware breaking info]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The beaglebone family of boards contain two I2C busses enabled.
The first one with a baseboard identification EEPROM and a
cape I2C bus.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Beaglebone Black doesn't have AES and SHAM enabled like the
original Beaglebone White dts. This breaks applications that
leverage the crypto blocks so fix this by enabling these nodes
in the am335x-bone-common.dtsi. With this change, enabling the
nodes in am335x-bone.dts is no longer required so remove them.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fixes: http://bugs.elinux.org/issues/127
the bb.org community was seeing random reboots before this change.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, this is the largest branch, though this time a little under
half of the total changes with 307 individual non-merge changesets.
The largest changes are the addition of new machines, in particular
the Tegra based Chromebook, the Renesas r8a7794 SoC, and DT support
for the old i.MX1 platform.
Other changes include
- at91: various sam9 and sama5 updates
- exynos: much extended Peach Pi/Pit (Chromebook 2) support
- keystone: new peripherals
- meson: added DT for meson6 SoC
- mvebu: new device support for Armada 370/375
- qcom: improved support for IPQ8064 and MSM8x60
- rockchip: much improved support for rk3288
- shmobile: lots of updates all over the place
- sunxi: dts license change
- sunxi: more a23 device support
- vexpress: CLCD DT description"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (308 commits)
ARM: DTS: meson: update DTSI to add watchdog node
ARM: dts: keystone-k2l: fix mdio io start address
ARM: dts: keystone-k2e: fix mdio io start address
ARM: dts: keystone-k2e: update usb1 node for dma properties
ARM: dts: keystone: fix io range for usb_phy0
Revert "Merge tag 'hix5hd2-dt-for-3.18' of git://github.com/hisilicon/linux-hisi into next/dt"
Revert "ARM: dts: hix5hd2: add wdg node"
ARM: dts: add rk3288 i2s controller
ARM: vexpress: Add CLCD Device Tree properties
ARM: bcm2835: add I2S pinctrl to device tree
ARM: meson: documentation: add bindings documentation
ARM: meson: dts: add basic Meson/Meson6/Meson6-atv1200 DTSI/DTS
ARM: dts: mt6589: Change compatible string for GIC
ARM: dts: mediatek: Add compatible property for aquaris5
ARM: dts: mt6589-aquaris5: Add boot argument earlyprintk
ARM: dts: mt6589: Fix typo in GIC unit address
ARM: dts: Build dtb for Mediatek board
ARM: dts: keystone: fix bindings for pcie and usb clock nodes
ARM: dts: keystone: k2l: Fix chip selects for SPI devices
ARM: dts: keystone: add dsp gpio controllers nodes
...
|
|
Add regulator-name properties for the regulators that don't have them,
allowing the kernel to display the name from the schematic rather than
the name of the regulator on the PMIC in order to improve diagnostics.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Beaglebone white and beaglebone black differ in tiny little aspects.
This is the reason why we maintain seperate dts for these platforms.
However, there is no real way to decode from dtb which platform it is
since compatible and model name are the same for both platforms.
Fix this so that beaglebone black and beaglebone are identifiable,
while maintaining compatibility for older zImages which might use old
beaglebone compatible flag for black as well.
Reported-by: Tom Rini <trini@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Make sure ethernet and mdio nodes are disabled by default and enable
them explicitly only on boards that actually use them.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
In "ARM: dts: am33xx: correcting dt node unit address for usb", the
usb_ctrl_mod and cppi41dma nodes were updated with the correct register
addresses. However, the dts files that reference these nodes were not
updated, and those devices are no longer being enabled.
This patch corrects the references for the affected dts files.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Set pinmux_emmc_pins mux mode for cmd line to MODE2 in order
to detect eMMC on BBB and BBW + eMMC cape.
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
3.3V fixed regulator does not belong to TPS node - as a result
the fixed regulator is never probed and MMC is continually deferred
due to lack of regulator.
Move the fixed regulator to be at root of platform.
Cc: Joel Fernandes <joelf@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
The On Chip Peripherals (OCP) device node is a simplified
representation of the AM33XX SoC interconnect. An OCP dev
node is already defined in the am33xx.dtsi Device Tree
source file included by am33xx based boards so there is
no need to redefine this on each board DT file.
Also, the OCP and IP modules directly connected to it are SoC
internal details that is better to keep outside of board files.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
am33xx boards DTS include the am33xx.dtsi Device Tree
source file that already define a pinmux device node for
the AM33XX SoC Pin Multiplex.
Redefining this for each board makes the Device Tree files
harder to modify and maintain so let's just use what is
already defined in the included .dtsi file.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
This matches the vendor 3.8.x configuration that is shipping
with the boards.
The LED layout is now:
USR0: heartbeat
USR1: mmc0 (micro-SD slot)
USR2: cpu0
USR3: mmc1 (eMMC)
The cpu0 triggers was put in between the mmc triggers to make
is easier to see where the disk activity is.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
The micro-SD slot hooks up all four data pins so lets' use them.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
The pinmux is specified in am335x-bone-common.dtsi to be
reused by the eMMC cape.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
[bcousson@baylibre.com: Fix traling spaces and useless comments]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
This enables the use of MMC cards even when no card was inserted at boot.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
The BeagleBone Black is basically a regular BeagleBone with eMMC and
HDMI added, so create a common dtsi both can use.
IMPORTANT: booting the existing am335x-bone.dts will blow up the HDMI
transceiver after a dozen boots with an uSD card inserted because LDO
will be at 3.3V instead of 1.8.
MMC support for AM335x still isn't in, so only the LDO change has been
added.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Tom Rini <trini@ti.com>
Tested-by: Matt Porter <matt.porter@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
