| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer
interface which allow setting multiple outputs with just one function call.
Also add an optional set_multiple function to the driver interface. Without an
implementation of that function in the chip driver outputs are set
sequentially.
Implementing the set_multiple function in a chip driver allows for:
- Improved performance for certain use cases. The original motivation for this
was the task of configuring an FPGA. In that specific case, where 9 GPIO
lines have to be set many times, configuration time goes down from 48 s to
20 s when using the new function.
- Simultaneous glitch-free setting of multiple pins on any kind of parallel
bus attached to GPIOs provided they all reside on the same chip and bank.
Limitations:
Performance is only improved for normal high-low outputs. Open drain and
open source outputs are always set separately from each other. Those kinds
of outputs could probably be accelerated in a similar way if we could
forgo the error checking when setting GPIO directions.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - check can_sleep property per chip
- remove superfluous checks
- supplement documentation
v4: - add gpiod_set_array function for setting logical values
- change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
- do not use ARCH_NR_GPIOS any more
v3: - add documentation
- change commit message
v2: - use descriptor interface
- allow arbitrary groups of GPIOs spanning multiple chips
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that ACPI supports named GPIO properties, either through ACPI 5.1 or
the per-driver ACPI GPIO mappings, we can be more narrow about the way
GPIOs should be specified in Device Tree bindings.
This patch updates the GPIO DT bindings documentation to highlight the
following rules for new GPIO bindings:
- All new bindings must have a meaningful name (e.g. the "gpios"
property must not be used)
- The only suffix allowed is "-gpios", no matter the number of
descriptors in the property
- GPIOs can only be grouped under the same property when they serve the
same purpose, a case that should remain exceptional (e.g. bit-banged
data lines).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This function actually operates on a gpio_chip, so its prefix should
reflect that fact for consistency with other functions defined in
gpio/driver.h.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Vybrid SoC device tree (vf610.dtsi) used this bindings since
its initial commit in May 2013. However, a proper gpiolib driver
was missing so far. With the addition of the gpiolib driver,
the bindings proved to be useful and complete, hence a good time
to add the documentation.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds DT binding documentation for the 74xx-mmio GPIO driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A batch of fixes that have come in during the merge window.
Some of them are defconfig updates for things that have now landed,
some errata additions and a few general scattered fixes.
There's also a qcom DT update that adds support for SATA on AP148, and
basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
isolated enough that we could merge it even if it's late"
* tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: corrected bcm2835 search
ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
ARM: dts: Explicitly set dr_mode on exynos Peach boards
ARM: dts: qcom: add CM-QS600 board
ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
ARM: dts: qcom: Add SATA support on IPQ8064/AP148
MAINTAINERS: Update Santosh Shilimkar's email id
ARM: sunxi_defconfig: enable CONFIG_REGULATOR
ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
ARM: exynos_defconfig: enable USB gadget support
ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
ARM: SAMSUNG: Restore Samsung PM Debug functionality
ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
ARM: exynos_defconfig: Enable SBS battery support
ARM: exynos_defconfig: Enable Control Groups support
ARM: exynos_defconfig: Enable Atmel maXTouch support
ARM: exynos_defconfig: Enable MAX77802
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into fixes
Merge "qcom DT changes for v3.18-3" from Kumar Gala:
Qualcomm ARM Based Device Tree Updates for v3.18-3
* Added Board support for CM-QS600 and Sony Xperia Z1 phone
* Added SATA support on IPQ8064/AP148
* tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: dts: qcom: add CM-QS600 board
ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
ARM: dts: qcom: Add SATA support on IPQ8064/AP148
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Highlights from the I2C subsystem for 3.18:
- new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC.
- designware driver gained AMD support, exynos gained exynos7 support
The rest is usual driver stuff. Hopefully no lowlights this time"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Add Device IDs for Intel Sunrise Point PCH
i2c: hix5hd2: add i2c controller driver
i2c-imx: Disable the clock on probe failure
i2c: designware: Add support for AMD I2C controller
i2c: designware: Rework probe() to get clock a bit later
i2c: designware: Default to fast mode in case of ACPI
i2c: axxia: Add I2C driver for AXM55xx
i2c: exynos: add support for HSI2C module on Exynos7
i2c: mxs: detect No Slave Ack on SELECT in PIO mode
i2c: cros_ec: Remove EC_I2C_FLAG_10BIT
i2c: cros-ec-tunnel: Add of match table
i2c: rcar: remove sign-compare flaw
i2c: ismt: Use minimum descriptor size
i2c: imx: Add arbitration lost check
i2c: rk3x: Remove unlikely() annotations
i2c: rcar: check for no IRQ in rcar_i2c_irq()
i2c: rcar: make rcar_i2c_prepare_msg() *void*
i2c: rcar: simplify check for last message
i2c: designware: add support of platform data to set I2C mode
i2c: designware: add support of I2C standard mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull second round of input updates from Dmitry Torokhov:
"Mostly simple bug fixes, although we do have one brand new driver for
Microchip AR1021 i2c touchscreen.
Also there is the change to stop trying to use i8042 active
multiplexing by default (it is still possible to activate it via
i8042.nomux=0 on boxes that implement it)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - add Thrustmaster as Xbox 360 controller vendor
Input: xpad - add USB ID for Thrustmaster Ferrari 458 Racing Wheel
Input: max77693-haptic - fix state check in imax77693_haptic_disable()
Input: xen-kbdfront - free grant table entry in xenkbd_disconnect_backend
Input: alps - fix v4 button press recognition
Input: i8042 - disable active multiplexing by default
Input: i8042 - add noloop quirk for Asus X750LN
Input: synaptics - gate forcepad support by DMI check
Input: Add Microchip AR1021 i2c touchscreen
Input: cros_ec_keyb - add of match table
Input: serio - avoid negative serio device numbers
Input: avoid negative input device numbers
Input: automatically set EV_ABS bit in input_set_abs_params
Input: adp5588-keys - cancel workqueue in failure path
Input: opencores-kbd - switch to using managed resources
Input: evdev - fix EVIOCG{type} ioctl
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull more perf updates from Ingo Molnar:
"A second (and last) round of late coming fixes and changes, almost all
of them in perf tooling:
User visible tooling changes:
- Add period data column and make it default in 'perf script' (Jiri
Olsa)
- Add a visual cue for toggle zeroing of samples in 'perf top'
(Taeung Song)
- Improve callchains when using libunwind (Namhyung Kim)
Tooling fixes and infrastructure changes:
- Fix for double free in 'perf stat' when using some specific invalid
command line combo (Yasser Shalabi)
- Fix off-by-one bugs in map->end handling (Stephane Eranian)
- Fix off-by-one bug in maps__find(), also related to map->end
handling (Namhyung Kim)
- Make struct symbol->end be the first addr after the symbol range,
to make it match the convention used for struct map->end. (Arnaldo
Carvalho de Melo)
- Fix perf_evlist__add_pollfd() error handling in 'perf kvm stat
live' (Jiri Olsa)
- Fix python test build by moving callchain_param to an object linked
into the python binding (Jiri Olsa)
- Document sysfs events/ interfaces (Cody P Schafer)
- Fix typos in perf/Documentation (Masanari Iida)
- Add missing 'struct option' forward declaration (Arnaldo Carvalho
de Melo)
- Add option to copy events when queuing for sorting across cpu
buffers and enable it for 'perf kvm stat live', to avoid having
events left in the queue pointing to the ring buffer be rewritten
in high volume sessions. (Alexander Yarygin, improving work done
by David Ahern):
- Do not include a struct hists per perf_evsel, untangling the
histogram code from perf_evsel, to pave the way for exporting a
minimalistic tools/lib/api/perf/ library usable by tools/perf and
initially by the rasd daemon being developed by Borislav Petkov,
Robert Richter and Jean Pihet. (Arnaldo Carvalho de Melo)
- Make perf_evlist__open(evlist, NULL, NULL), i.e. without cpu and
thread maps mean syswide monitoring, reducing the boilerplate for
tools that only want system wide mode. (Arnaldo Carvalho de Melo)
- Move exit stuff from perf_evsel__delete to perf_evsel__exit, delete
should be just a front end for exit + free (Arnaldo Carvalho de
Melo)
- Add support to new style format of kernel PMU event. (Kan Liang)
and other misc fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
perf script: Add period as a default output column
perf script: Add period data column
perf evsel: No need to drag util/cgroup.h
perf evlist: Add missing 'struct option' forward declaration
perf evsel: Move exit stuff from __delete to __exit
kprobes/x86: Remove stale ARCH_SUPPORTS_KPROBES_ON_FTRACE define
perf kvm stat live: Enable events copying
perf session: Add option to copy events when queueing
perf Documentation: Fix typos in perf/Documentation
perf trace: Use thread_{,_set}_priv helpers
perf kvm: Use thread_{,_set}_priv helpers
perf callchain: Create an address space per thread
perf report: Set callchain_param.record_mode for future use
perf evlist: Fix for double free in tools/perf stat
perf test: Add test case for pmu event new style format
perf tools: Add support to new style format of kernel PMU event
perf tools: Parse the pmu event prefix and suffix
Revert "perf tools: Default to cpu// for events v5"
perf Documentation: Remove Ruplicated docs for powerpc cpu specific events
perf Documentation: sysfs events/ interfaces
...
|
|
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- new 6x10 font
- various small fixes and cleanups
* tag 'fbdev-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (30 commits)
fonts: Add 6x10 font
videomode: provide dummy inline functions for !CONFIG_OF
video/atmel_lcdfb: Introduce regulator support
fbdev: sh_mobile_hdmi: Re-init regs before irq re-enable on resume
framebuffer: fix screen corruption when copying
framebuffer: fix border color
arm, fbdev, omap2, LLVMLinux: Remove nested function from omapfb
arm, fbdev, omap2, LLVMLinux: Remove nested function from omap2 dss
video: fbdev: valkyriefb.c: use container_of to resolve fb_info_valkyrie from fb_info
video: fbdev: pxafb.c: use container_of to resolve pxafb_info/layer from fb_info
video: fbdev: cyber2000fb.c: use container_of to resolve cfb_info from fb_info
video: fbdev: controlfb.c: use container_of to resolve fb_info_control from fb_info
video: fbdev: sa1100fb.c: use container_of to resolve sa1100fb_info from fb_info
video: fbdev: stifb.c: use container_of to resolve stifb_info from fb_info
video: fbdev: sis: sis_main.c: Cleaning up missing null-terminate in conjunction with strncpy
video: valkyriefb: Fix unused variable warning in set_valkyrie_clock()
video: fbdev: use %*ph specifier to dump small buffers
video: mx3fb: always enable BACKLIGHT_LCD_SUPPORT
video: fbdev: au1200fb: delete double assignment
video: fbdev: sis: delete double assignment
...
|
|
Pull NTFS update from Anton Altaparmakov:
"Here is a small NTFS update notably implementing FIBMAP ioctl for NTFS
by adding the bmap address space operation. People seem to still want
FIBMAP"
* git://git.kernel.org/pub/scm/linux/kernel/git/aia21/ntfs:
NTFS: Bump version to 2.1.31.
NTFS: Add bmap address space operation needed for FIBMAP ioctl.
NTFS: Remove changelog from Documentation/filesystems/ntfs.txt.
NTFS: Split ntfs_aops into ntfs_normal_aops and ntfs_compressed_aops in preparation for them diverging.
|
|
Pull core block layer changes from Jens Axboe:
"This is the core block IO pull request for 3.18. Apart from the new
and improved flush machinery for blk-mq, this is all mostly bug fixes
and cleanups.
- blk-mq timeout updates and fixes from Christoph.
- Removal of REQ_END, also from Christoph. We pass it through the
->queue_rq() hook for blk-mq instead, freeing up one of the request
bits. The space was overly tight on 32-bit, so Martin also killed
REQ_KERNEL since it's no longer used.
- blk integrity updates and fixes from Martin and Gu Zheng.
- Update to the flush machinery for blk-mq from Ming Lei. Now we
have a per hardware context flush request, which both cleans up the
code should scale better for flush intensive workloads on blk-mq.
- Improve the error printing, from Rob Elliott.
- Backing device improvements and cleanups from Tejun.
- Fixup of a misplaced rq_complete() tracepoint from Hannes.
- Make blk_get_request() return error pointers, fixing up issues
where we NULL deref when a device goes bad or missing. From Joe
Lawrence.
- Prep work for drastically reducing the memory consumption of dm
devices from Junichi Nomura. This allows creating clone bio sets
without preallocating a lot of memory.
- Fix a blk-mq hang on certain combinations of queue depths and
hardware queues from me.
- Limit memory consumption for blk-mq devices for crash dump
scenarios and drivers that use crazy high depths (certain SCSI
shared tag setups). We now just use a single queue and limited
depth for that"
* 'for-3.18/core' of git://git.kernel.dk/linux-block: (58 commits)
block: Remove REQ_KERNEL
blk-mq: allocate cpumask on the home node
bio-integrity: remove the needless fail handle of bip_slab creating
block: include func name in __get_request prints
block: make blk_update_request print prefix match ratelimited prefix
blk-merge: don't compute bi_phys_segments from bi_vcnt for cloned bio
block: fix alignment_offset math that assumes io_min is a power-of-2
blk-mq: Make bt_clear_tag() easier to read
blk-mq: fix potential hang if rolling wakeup depth is too high
block: add bioset_create_nobvec()
block: use bio_clone_fast() in blk_rq_prep_clone()
block: misplaced rq_complete tracepoint
sd: Honor block layer integrity handling flags
block: Replace strnicmp with strncasecmp
block: Add T10 Protection Information functions
block: Don't merge requests if integrity flags differ
block: Integrity checksum flag
block: Relocate bio integrity flags
block: Add a disk flag to block integrity profile
block: Add prefix to block integrity profile flags
...
|
|
Pull MTD update from Brian Norris:
"Sorry for delaying this a bit later than usual. There's one mild
regression from 3.16 that was noticed during the 3.17 cycle, and I
meant to send a fix for it along with this pull request. I'll
probably try to queue it up for a later pull request once I've had a
better look at it, hopefully by -rc2 at the latest.
Summary for this pull:
NAND
- Cleanup for Denali driver
- Atmel: add support for new page sizes
- Atmel: fix up 'raw' mode support
- Atmel: miscellaneous cleanups
- New timing mode helpers for non-ONFI NAND
- OMAP: allow driver to be (properly) built as a module
- bcm47xx: RESET support and other cleanups
SPI NOR
- Miscellaneous cleanups, to prepare framework for wider use (some
further work still pending)
- Compile-time configuration to select 4K vs. 64K support for flash
that support both (necessary for using UBIFS on some SPI NOR)
A few scattered code quality fixes, detected by Coverity
See the changesets for more"
* tag 'for-linus-20141015' of git://git.infradead.org/linux-mtd: (59 commits)
mtd: nand: omap: Correct CONFIG_MTD_NAND_OMAP_BCH help message
mtd: nand: Force omap_elm to be built as a module if omap2_nand is a module
mtd: move support for struct flash_platform_data into m25p80
mtd: spi-nor: add Kconfig option to disable 4K sectors
mtd: nand: Move ELM driver and rename as omap_elm
nand: omap2: Replace pr_err with dev_err
nand: omap2: Remove horrible ifdefs to fix module probe
mtd: nand: add Hynix's H27UCG8T2ATR-BC to nand_ids table
mtd: nand: support ONFI timing mode retrieval for non-ONFI NANDs
mtd: physmap_of: Add non-obsolete map_rom probe
mtd: physmap_of: Fix ROM support via OF
MAINTAINERS: add l2-mtd.git, 'next' tree for MTD
mtd: denali: fix indents and other trivial things
mtd: denali: remove unnecessary parentheses
mtd: denali: remove another set-but-unused variable
mtd: denali: fix include guard and license block of denali.h
mtd: nand: don't break long print messages
mtd: bcm47xxnflash: replace some magic numbers
mtd: bcm47xxnflash: NAND_CMD_RESET support
mtd: bcm47xxnflash: add cmd_ctrl handler
...
|
|
Pull networking fixes from David Miller:
1) Include fixes for netrom and dsa (Fabian Frederick and Florian
Fainelli)
2) Fix FIXED_PHY support in stmmac, from Giuseppe CAVALLARO.
3) Several SKB use after free fixes (vxlan, openvswitch, vxlan,
ip_tunnel, fou), from Li ROngQing.
4) fec driver PTP support fixes from Luwei Zhou and Nimrod Andy.
5) Use after free in virtio_net, from Michael S Tsirkin.
6) Fix flow mask handling for megaflows in openvswitch, from Pravin B
Shelar.
7) ISDN gigaset and capi bug fixes from Tilman Schmidt.
8) Fix route leak in ip_send_unicast_reply(), from Vasily Averin.
9) Fix two eBPF JIT bugs on x86, from Alexei Starovoitov.
10) TCP_SKB_CB() reorganization caused a few regressions, fixed by Cong
Wang and Eric Dumazet.
11) Don't overwrite end of SKB when parsing malformed sctp ASCONF
chunks, from Daniel Borkmann.
12) Don't call sock_kfree_s() with NULL pointers, this function also has
the side effect of adjusting the socket memory usage. From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
bna: fix skb->truesize underestimation
net: dsa: add includes for ethtool and phy_fixed definitions
openvswitch: Set flow-key members.
netrom: use linux/uaccess.h
dsa: Fix conversion from host device to mii bus
tipc: fix bug in bundled buffer reception
ipv6: introduce tcp_v6_iif()
sfc: add support for skb->xmit_more
r8152: return -EBUSY for runtime suspend
ipv4: fix a potential use after free in fou.c
ipv4: fix a potential use after free in ip_tunnel_core.c
hyperv: Add handling of IP header with option field in netvsc_set_hash()
openvswitch: Create right mask with disabled megaflows
vxlan: fix a free after use
openvswitch: fix a use after free
ipv4: dst_entry leak in ip_send_unicast_reply()
ipv4: clean up cookie_v4_check()
ipv4: share tcp_v4_save_options() with cookie_v4_check()
ipv4: call __ip_options_echo() in cookie_v4_check()
atm: simplify lanai.c by using module_pci_driver
...
|
|
Changelog is in git history, no need to have a copy in the documentation.
Signed-off-by: Anton Altaparmakov <anton@tuxera.com>
|
|
This DTS has support for the Sony Xperia Z1 phone (codenamed Honami).
This first version of the DTS supports just a serial console.
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
|
|
This patch adds the I2C/SMBus Device IDs for the Intel Sunrise Point PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
I2C drivers for hix5hd2 soc series, including following chipset
Hi3716CV200, Hi3719CV100, Hi3718CV100, Hi3719MV100, Hi3718MV100.
Signed-off-by: Wei Yan <sledge.yanwei@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
[wsa: folded dt docs into this patch]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Listing specific events doesn't actually help us at all here because:
- these events actually vary between different ppc processors, they
aren't garunteed to be present.
- the documentation of the (generic) file contents is now superceded by the
docs for arbitrary event file contents.
Signed-off-by: Cody P Schafer <dev@codyps.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Haren Myneni <hbabu@us.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Michael Ellerman <michaele@au1.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/1412143402-26061-5-git-send-email-sukadev@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Add documentation for the <event>, <event>.scale, and <event>.unit
files in sysfs.
<event>.scale and <event>.unit were undocumented.
<event> was previously documented only for specific powerpc pmu events.
Signed-off-by: Cody P Schafer <dev@codyps.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Cody P Schafer <dev@codyps.com>
Cc: Haren Myneni <hbabu@us.ibm.com>
Cc: Haren Myneni <hbabu@us.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Michael Ellerman <michaele@au1.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/1412143402-26061-4-git-send-email-sukadev@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"This pull-request includes:
- change in the IOMMU-API to convert the former iommu_domain_capable
function to just iommu_capable
- various fixes in handling RMRR ranges for the VT-d driver (one fix
requires a device driver core change which was acked by Greg KH)
- the AMD IOMMU driver now assigns and deassigns complete alias
groups to fix issues with devices using the wrong PCI request-id
- MMU-401 support for the ARM SMMU driver
- multi-master IOMMU group support for the ARM SMMU driver
- various other small fixes all over the place"
* tag 'iommu-updates-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (41 commits)
iommu/vt-d: Work around broken RMRR firmware entries
iommu/vt-d: Store bus information in RMRR PCI device path
iommu/vt-d: Only remove domain when device is removed
driver core: Add BUS_NOTIFY_REMOVED_DEVICE event
iommu/amd: Fix devid mapping for ivrs_ioapic override
iommu/irq_remapping: Fix the regression of hpet irq remapping
iommu: Fix bus notifier breakage
iommu/amd: Split init_iommu_group() from iommu_init_device()
iommu: Rework iommu_group_get_for_pci_dev()
iommu: Make of_device_id array const
amd_iommu: do not dereference a NULL pointer address.
iommu/omap: Remove omap_iommu unused owner field
iommu: Remove iommu_domain_has_cap() API function
IB/usnic: Convert to use new iommu_capable() API function
vfio: Convert to use new iommu_capable() API function
kvm: iommu: Convert to use new iommu_capable() API function
iommu/tegra: Convert to iommu_capable() API function
iommu/msm: Convert to iommu_capable() API function
iommu/vt-d: Convert to iommu_capable() API function
iommu/fsl: Convert to iommu_capable() API function
...
|
|
git://git.linaro.org/people/mike.turquette/linux
Pull clock tree updates from Mike Turquette:
"The clk tree changes for 3.18 are dominated by clock drivers. Mostly
fixes and enhancements to existing drivers as well as new drivers.
This tag contains a bit more arch code than I usually take due to some
OMAP2+ changes. Additionally it contains the restart notifier
handlers which are merged as a dependency into several trees.
The PXA changes are the only messy part. Due to having a stable tree
I had to revert one patch and follow up with one more fix near the tip
of this tag. Some dead code is introduced but it will soon become
live code after 3.18-rc1 is released as the rest of the PXA family is
converted over to the common clock framework.
Another trend in this tag is that multiple vendors have started to
push the complexity of changing their CPU frequency into the clock
driver, whereas this used to be done in CPUfreq drivers.
Changes to the clk core include a generic gpio-clock type and a
clk_set_phase() function added to the top-level clk.h api. Due to
some confusion on the fbdev mailing list the kernel boot parameters
documentation was updated to further explain the clk_ignore_unused
parameter, which is often required by users of the simplefb driver.
Finally some fixes to the locking around the clock debugfs stuff was
done to prevent deadlocks when interacting with other subsystems."
* tag 'clk-for-linus-3.18' of git://git.linaro.org/people/mike.turquette/linux: (99 commits)
clk: pxa clocks build system fix
Revert "arm: pxa: Transition pxa27x to clk framework"
clk: samsung: register restart handlers for s3c2412 and s3c2443
clk: rockchip: add restart handler
clk: rockchip: rk3288: i2s_frac adds flag to set parent's rate
doc/kernel-parameters.txt: clarify clk_ignore_unused
arm: pxa: Transition pxa27x to clk framework
dts: add devicetree bindings for pxa27x clocks
clk: add pxa27x clock drivers
arm: pxa: add clock pll selection bits
clk: dts: document pxa clock binding
clk: add pxa clocks infrastructure
clk: gpio-gate: Ensure gpiod_ APIs are prototyped
clk: ti: dra7-atl-clock: Mark the device as pm_runtime_irq_safe
clk: ti: LLVMLinux: Move __init outside of type definition
clk: ti: consider the fact that of_clk_get() might return an error
clk: ti: dra7-atl-clock: fix a memory leak
clk: ti: change clock init to use generic of_clk_init
clk: hix5hd2: add I2C clocks
clk: hix5hd2: add watchdog0 clocks
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Changes to existing drivers:
- DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030
- Export symbols for use in modules in max14577
- Plenty of static code analysis/Coccinelle fixes throughout the SS
- Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808
- Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona
- Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr
- IRQ fixups in arizona, stmpe, max14577
- Regulator related changes in axp20x
- Pass DMA coherency information from parent => child in MFD core
- Rename DT document files for consistency
- Add ACPI support to the MFD core
- Add Andreas Werner to MAINTAINERS for MEN F21BMC
New drivers/supported devices:
- New driver for MEN 14F021P00 Board Management Controller
- New driver for Ricoh RN5T618 PMIC
- New driver for Rockchip RK808
- New driver for HiSilicon Hi6421 PMIC
- New driver for Qualcomm SPMI PMICs
- Add support for Intel Braswell in lpc_ich
- Add support for Intel 9 Series PCH in lpc_ich
- Add support for Intel Quark ILB in lpc_sch"
[ Delayed to after the poweer/reset pull due to Kconfig problems with
recursive Kconfig select/depends-on chains. - Linus ]
* tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (79 commits)
mfd: cros_ec: wait for completion of commands that return IN_PROGRESS
i2c: i2c-cros-ec-tunnel: Set retries to 3
mfd: cros_ec: move locking into cros_ec_cmd_xfer
mfd: cros_ec: stop calling ->cmd_xfer() directly
mfd: cros_ec: Delay for 50ms when we see EC_CMD_REBOOT_EC
MAINTAINERS: Adds Andreas Werner to maintainers list for MEN F21BMC
mfd: arizona: Correct mask to allow setting micbias external cap
mfd: Add ACPI support
Revert "mfd: wm5102: Manually apply register patch"
mfd: ti_am335x_tscadc: Update logic in CTRL register for 5-wire TS
mfd: dt-bindings: atmel-gpbr: Rename doc file to conform to naming convention
mfd: dt-bindings: qcom-pm8xxx: Rename doc file to conform to naming convention
mfd: Inherit coherent_dma_mask from parent device
mfd: Document DT bindings for Qualcomm SPMI PMICs
mfd: Add support for Qualcomm SPMI PMICs
mfd: dt-bindings: pm8xxx: Add new compatible string
mfd: axp209x: Drop the parent supplies field
mfd: twl4030-power: Use 'ti,system-power-controller' as alternative way to support system power off
mfd: dt-bindings: twl4030-power: Use the standard property to mark power control
mfd: syscon: Add Atmel GPBR DT bindings documention
...
|
|
Pull power supply and reset updates from Sebastian Reichel:
- Initial support for the following chips
* max77836 (charger)
* max14577 (charger)
* bq27742 (battery gauge)
* ltc2952 (poweroff)
* stih416 (restart)
* syscon-reboot (restart)
* gpio-restart (restart)
- cleanup of power supply core
- misc fixes in power supply and reset drivers
* tag 'for-v3.18' of git://git.infradead.org/battery-2.6: (48 commits)
power: ab8500_fg: Fix build warning
Documentation: charger: max14577: Update the date of introducing ABI
power: reset: corrections for simple syscon reboot driver
Documentation: power: reset: Add documentation for generic SYSCON reboot driver
power: reset: Add generic SYSCON register mapped reset
bq27x00_battery: Fix flag reading for bq27742
power: reset: use restart_notifier mechanism for msm-poweroff
power: Add simple gpio-restart driver
power: reset: st: Provide DT bindings for ST's Power Reset driver
power: reset: Add restart functionality for STiH41x platforms
power: charger-manager: Fix NULL pointer exception with missing cm-fuel-gauge
power: max14577: Fix circular config SYSFS dependency
power: gpio-charger: do not use gpio value directly
power: max8925: Use of_get_child_by_name
power: max8925: Fix NULL ptr dereference on memory allocation failure
bq27x00_battery: Add support to bq27742
Documentation: charger: max14577: Document exported sysfs entry
devicetree: mfd: max14577: Add device tree bindings document
power: max17040: Add ID for MAX77836 Fuel Gauge block
charger: max14577: Configure battery-dependent settings from DTS and sysfs
...
Conflicts:
drivers/power/reset/Kconfig
drivers/power/reset/Makefile
|
|
This patch is to review the whole glue logic adopted on STi SoCs that
was bugged.
In the old glue-logic there was a lot of confusion when setup the
retiming especially for STiD127 where, for example, the bits 6 and 7
(in the GMAC control register) have a different meaning of what is
used for STiH4xx SoCs. So we cannot adopt the same glue for all these
SoCs.
Moreover, GiGa on STiD127 didn't work and, for all the SoCs, the RGMII
couldn't run when the speed was 10Mbps (because the clock was not properly
managed).
Note that the phy clock needs to be provided by the platform as well as
documented in the related binding file (updated as consequence).
The old code supported too many configurations never adopted and validated.
This made the code very complex to maintain and debug in case of issues.
The patch simplifies all the configurations as commented in the tables
inside the file and obviously it has been tested on all the boards
based on the SoCs mentioned.
With this patch, the dwmac-sti is also ready to support new configurations that
will be available on next SoC generations.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds the missing compatibility to the STiH407 SoC.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm updates from Dave Airlie:
"This is the main git pull for the drm,
I pretty much froze major pulls at -rc5/6 time, and haven't had much
fallout, so will probably continue doing that.
Lots of changes all over, big internal header cleanup to make it clear
drm features are legacy things and what are things that modern KMS
drivers should be using. Also big move to use the new generic fences
in all the TTM drivers.
core:
atomic prep work,
vblank rework changes, allows immediate vblank disables
major header reworking and cleanups to better delinate legacy
interfaces from what KMS drivers should be using.
cursor planes locking fixes
ttm:
move to generic fences (affects all TTM drivers)
ppc64 caching fixes
radeon:
userptr support,
uvd for old asics,
reset rework for fence changes
better buffer placement changes,
dpm feature enablement
hdmi audio support fixes
intel:
Cherryview work,
180 degree rotation,
skylake prep work,
execlist command submission
full ppgtt prep work
cursor improvements
edid caching,
vdd handling improvements
nouveau:
fence reworking
kepler memory clock work
gt21x clock work
fan control improvements
hdmi infoframe fixes
DP audio
ast:
ppc64 fixes
caching fix
rcar:
rcar-du DT support
ipuv3:
prep work for capture support
msm:
LVDS support for mdp4, new panel, gpu refactoring
exynos:
exynos3250 SoC support, drop bad mmap interface,
mipi dsi changes, and component match support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (640 commits)
drm/mst: rework payload table allocation to conform better.
drm/ast: Fix HW cursor image
drm/radeon/kv: add uvd/vce info to dpm debugfs output
drm/radeon/ci: add uvd/vce info to dpm debugfs output
drm/radeon: export reservation_object from dmabuf to ttm
drm/radeon: cope with foreign fences inside the reservation object
drm/radeon: cope with foreign fences inside display
drm/core: use helper to check driver features
drm/radeon/cik: write gfx ucode version to ucode addr reg
drm/radeon/si: print full CS when we hit a packet 0
drm/radeon: remove unecessary includes
drm/radeon/combios: declare legacy_connector_convert as static
drm/radeon/atombios: declare connector convert tables as static
drm/radeon: drop btc_get_max_clock_from_voltage_dependency_table
drm/radeon/dpm: drop clk/voltage dependency filters for BTC
drm/radeon/dpm: drop clk/voltage dependency filters for CI
drm/radeon/dpm: drop clk/voltage dependency filters for SI
drm/radeon/dpm: drop clk/voltage dependency filters for NI
drm/radeon: disable audio when we disable hdmi (v2)
drm/radeon: split audio enable between eg and r600 (v2)
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull misc kbuild updates from Michal Marek:
"This is the less critical kbuild stuff for v3.18-rc1:
- make deb-pkg debuginfo fix, ppc64el support and warning fix for
recent dpkg tools
- make TAGS fixes
- new coccinelle patch
- kbuild documentation improvements"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
deb-pkg: remove obsolete -isp option to dpkg-gencontrol
coccinelle: misc: semantic patch to delete overly complex return code processing
deb-pkg: Add support for powerpc little endian
builddeb: put the dbg files into the correct directory
scripts/tags.sh: fix DEFINE_HASHTABLE in emacs case
scripts/tags.sh: remove *PCGFLAGS regular expressions
scripts/tags.sh: Don't specify kind-spec for emacs' ctags/etags
Documentation: kbuild: Improve grammar
Documentation: kbuild: Remove obsolete dtc_cpp section
Documentation: kbuild: Improve if_changed documentation
Documentation: kbuild: Remove obsolete include/asm symlink step
|
|
Merge second patch-bomb from Andrew Morton:
- a few hotfixes
- drivers/dma updates
- MAINTAINERS updates
- Quite a lot of lib/ updates
- checkpatch updates
- binfmt updates
- autofs4
- drivers/rtc/
- various small tweaks to less used filesystems
- ipc/ updates
- kernel/watchdog.c changes
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (135 commits)
mm: softdirty: enable write notifications on VMAs after VM_SOFTDIRTY cleared
kernel/param: consolidate __{start,stop}___param[] in <linux/moduleparam.h>
ia64: remove duplicate declarations of __per_cpu_start[] and __per_cpu_end[]
frv: remove unused declarations of __start___ex_table and __stop___ex_table
kvm: ensure hard lockup detection is disabled by default
kernel/watchdog.c: control hard lockup detection default
staging: rtl8192u: use %*pEn to escape buffer
staging: rtl8192e: use %*pEn to escape buffer
staging: wlan-ng: use %*pEhp to print SN
lib80211: remove unused print_ssid()
wireless: hostap: proc: print properly escaped SSID
wireless: ipw2x00: print SSID via %*pE
wireless: libertas: print esaped string via %*pE
lib/vsprintf: add %*pE[achnops] format specifier
lib / string_helpers: introduce string_escape_mem()
lib / string_helpers: refactoring the test suite
lib / string_helpers: move documentation to c-file
include/linux: remove strict_strto* definitions
arch/x86/mm/numa.c: fix boot failure when all nodes are hotpluggable
fs: check bh blocknr earlier when searching lru
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
"This patch set contains the main portion of the changes for 3.18 in
regard to the s390 architecture. It is a bit bigger than usual,
mainly because of a new driver and the vector extension patches.
The interesting bits are:
- Quite a bit of work on the tracing front. Uprobes is enabled and
the ftrace code is reworked to get some of the lost performance
back if CONFIG_FTRACE is enabled.
- To improve boot time with CONFIG_DEBIG_PAGEALLOC, support for the
IPTE range facility is added.
- The rwlock code is re-factored to improve writer fairness and to be
able to use the interlocked-access instructions.
- The kernel part for the support of the vector extension is added.
- The device driver to access the CD/DVD on the HMC is added, this
will hopefully come in handy to improve the installation process.
- Add support for control-unit initiated reconfiguration.
- The crypto device driver is enhanced to enable the additional AP
domains and to allow the new crypto hardware to be used.
- Bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (39 commits)
s390/ftrace: simplify enabling/disabling of ftrace_graph_caller
s390/ftrace: remove 31 bit ftrace support
s390/kdump: add support for vector extension
s390/disassembler: add vector instructions
s390: add support for vector extension
s390/zcrypt: Toleration of new crypto hardware
s390/idle: consolidate idle functions and definitions
s390/nohz: use a per-cpu flag for arch_needs_cpu
s390/vtime: do not reset idle data on CPU hotplug
s390/dasd: add support for control unit initiated reconfiguration
s390/dasd: fix infinite loop during format
s390/mm: make use of ipte range facility
s390/setup: correct 4-level kernel page table detection
s390/topology: call set_sched_topology early
s390/uprobes: architecture backend for uprobes
s390/uprobes: common library for kprobes and uprobes
s390/rwlock: use the interlocked-access facility 1 instructions
s390/rwlock: improve writer fairness
s390/rwlock: remove interrupt-enabling rwlock variant.
s390/mm: remove change bit override support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 mm updates from Ingo Molnar:
"This tree includes the following changes:
- fix memory hotplug
- fix hibernation bootup memory layout assumptions
- fix hyperv numa guest kernel messages
- remove dead code
- update documentation"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Update memory map description to list hypervisor-reserved area
x86/mm, hibernate: Do not assume the first e820 area to be RAM
x86/mm/numa: Drop dead code and rename setup_node_data() to setup_alloc_data()
x86/mm/hotplug: Modify PGD entry when removing memory
x86/mm/hotplug: Pass sync_global_pgds() a correct argument in remove_pagetable()
x86: Remove set_pmd_pfn
|
|
This allows user to print a given buffer as an escaped string. The
rules are applied according to an optional mix of flags provided by
additional format letters.
For example, if the given buffer is:
1b 62 20 5c 43 07 22 90 0d 5d
The result strings would be:
%*pE "\eb \C\a"\220\r]"
%*pEhp "\x1bb \C\x07"\x90\x0d]"
%*pEa "\e\142\040\\\103\a\042\220\r\135"
Please, read Documentation/printk-formats.txt and lib/string_helpers.c
kernel documentation to get further information.
[akpm@linux-foundation.org: tidy up comment layout, per Joe]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Joe Perches <joe@perches.com>
Cc: "John W . Linville" <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
format_corename() can only pass the leader's pid to the core handler,
but there is no simple way to figure out which thread originated the
coredump.
As Jan explains, this also means that there is no simple way to create
the backtrace of the crashed process:
As programs are mostly compiled with implicit gcc -fomit-frame-pointer
one needs program's .eh_frame section (equivalently PT_GNU_EH_FRAME
segment) or .debug_frame section. .debug_frame usually is present only
in separate debug info files usually not even installed on the system.
While .eh_frame is a part of the executable/library (and it is even
always mapped for C++ exceptions unwinding) it no longer has to be
present anywhere on the disk as the program could be upgraded in the
meantime and the running instance has its executable file already
unlinked from disk.
One possibility is to echo 0x3f >/proc/*/coredump_filter and dump all
the file-backed memory including the executable's .eh_frame section.
But that can create huge core files, for example even due to mmapped
data files.
Other possibility would be to read .eh_frame from /proc/PID/mem at the
core_pattern handler time of the core dump. For the backtrace one needs
to read the register state first which can be done from core_pattern
handler:
ptrace(PTRACE_SEIZE, tid, 0, PTRACE_O_TRACEEXIT)
close(0); // close pipe fd to resume the sleeping dumper
waitpid(); // should report EXIT
PTRACE_GETREGS or other requests
The remaining problem is how to get the 'tid' value of the crashed
thread. It could be read from the first NT_PRSTATUS note of the core
file but that makes the core_pattern handler complicated.
Unfortunately %t is already used so this patch uses %i/%I.
Automatic Bug Reporting Tool (https://github.com/abrt/abrt/wiki/overview)
is experimenting with this. It is using the elfutils
(https://fedorahosted.org/elfutils/) unwinder for generating the
backtraces. Apart from not needing matching executables as mentioned
above, another advantage is that we can get the backtrace without saving
the core (which might be quite large) to disk.
[mmilata@redhat.com: final paragraph of changelog]
Signed-off-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Mark Wielaard <mjw@redhat.com>
Cc: Martin Milata <mmilata@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
BQ32000 have "trickle chargers". Introduce a device tree binding for
specifying the trickle charger configuration for that.
Signed-off-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jason Cooper <jason@lakedameon.net>
Cc: Matti Vaittinen <matti.vaittinen@nsn.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some DS13XX devices have "trickle chargers". Introduce a device tree
binding for the resistor and diode configuration for enabling trickle
charger.
Signed-off-by: Matti Vaittinen <matti.vaittinen@nsn.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pavel Machek <pavel@denx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add support for RTC of Exynos3250 SoC. The Exynos3250 needs source
clock(32.768KHz) for RTC block. If source clock of RTC is registerd on
clock list of common clk framework, Exynos RTC drvier have to control
this clock.
Clock list for s3c-rtc device:
- rtc : CLK_RTC of CLK_GATE_IP_PERIR is gate clock for RTC.
- rtc_src : XrtcXTI is 32.768.kHz source clock for RTC.
(XRTCXTI: Specifies a clock from 32.768 kHz crystal pad with XRTCXTI and
XRTCXTO pins. RTC uses this clock as the source of a real-time clock.)
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
script
Remove warning message when checking codeing style with checkpatch script
and reduce un-necessary i2c read operation on s3c_rtc_enable.
WARNING: line over 80 characters
#406: FILE: drivers/rtc/rtc-s3c.c:406:
+ if ((readw(info->base + S3C2410_RTCCON) & S3C2410_RTCCON_RTCEN) == 0) {
WARNING: line over 80 characters
#414: FILE: drivers/rtc/rtc-s3c.c:414:
+ if ((readw(info->base + S3C2410_RTCCON) & S3C2410_RTCCON_CNTSEL)) {
WARNING: line over 80 characters
#422: FILE: drivers/rtc/rtc-s3c.c:422:
+ if ((readw(info->base + S3C2410_RTCCON) & S3C2410_RTCCON_CLKRST)) {
WARNING: Missing a blank line after declarations
#451: FILE: drivers/rtc/rtc-s3c.c:451:
+ struct s3c_rtc_drv_data *data;
+ if (pdev->dev.of_node) {
WARNING: Missing a blank line after declarations
#453: FILE: drivers/rtc/rtc-s3c.c:453:
+ const struct of_device_id *match;
+ match = of_match_node(s3c_rtc_dt_match, pdev->dev.of_node);
WARNING: DT compatible string "samsung,s3c2416-rtc" appears un-documented -- check ./Documentation/devicetree/bindings/
#650: FILE: drivers/rtc/rtc-s3c.c:650:
+ .compatible = "samsung,s3c2416-rtc",
WARNING: DT compatible string "samsung,s3c2443-rtc" appears un-documented -- check ./Documentation/devicetree/bindings/
#653: FILE: drivers/rtc/rtc-s3c.c:653:
+ .compatible = "samsung,s3c2443-rtc",
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This documents autofs from the perspective of what the module actually
supports rather than how automount is expected to use it.
It is formatted using "markdown" and works best with Markdown.pl
(markdown_py doesn't like some constructs).
[rdunlap@infradead.org: copy editing]
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Line wrap the content to 80 cols, and add more details to various fields
to match the code. Drop reference to a website that does not exist
anymore.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The current code places a 256 byte limit on the registration format.
This ends up being fairly limited when you try to do matching against a
binary format like ELF:
- the magic & mask formats cannot have any embedded NUL chars
(string_unescape_inplace halts at the first NUL)
- each escape sequence quadruples the size: \x00 is needed for NUL
- trying to match bytes at the start of the file as well as further
on leads to a lot of \x00 sequences in the mask
- magic & mask have to be the same length (when decoded)
- still need bytes for the other fields
- impossible!
Let's look at a concrete (and common) example: using QEMU to run MIPS
ELFs. The name field uses 11 bytes "qemu-mipsel". The interp uses 20
bytes "/usr/bin/qemu-mipsel". The type & flags takes up 4 bytes. We
need 7 bytes for the delimiter (usually ":"). We can skip offset. So
already we're down to 107 bytes to use with the magic/mask instead of
the real limit of 128 (BINPRM_BUF_SIZE). If people use shell code to
register (which they do the majority of the time), they're down to ~26
possible bytes since the escape sequence must be \x##.
The ELF format looks like (both 32 & 64 bit):
e_ident: 16 bytes
e_type: 2 bytes
e_machine: 2 bytes
Those 20 bytes are enough for most architectures because they have so few
formats in the first place, thus they can be uniquely identified. That
also means for shell users, since 20 is smaller than 26, they can sanely
register a handler.
But for some targets (like MIPS), we need to poke further. The ELF fields
continue on:
e_entry: 4 or 8 bytes
e_phoff: 4 or 8 bytes
e_shoff: 4 or 8 bytes
e_flags: 4 bytes
We only care about e_flags here as that includes the bits to identify
whether the ELF is O32/N32/N64. But now we have to consume another 16
bytes (for 32 bit ELFs) or 28 bytes (for 64 bit ELFs) just to match the
flags. If every byte is escaped, we send 288 more bytes to the kernel
((20 {e_ident,e_type,e_machine} + 12 {e_entry,e_phoff,e_shoff} + 4
{e_flags}) * 2 {mask,magic} * 4 {escape}) and we've clearly blown our
budget.
Even if we try to be clever and do the decoding ourselves (rather than
relying on the kernel to process \x##), we still can't hit the mark --
string_unescape_inplace treats mask & magic as C strings so NUL cannot
be embedded. That leaves us with having to pass \x00 for the 12/24
entry/phoff/shoff bytes (as those will be completely random addresses),
and that is a minimum requirement of 48/96 bytes for the mask alone.
Add up the rest and we blow through it (this is for 64 bit ELFs):
magic: 20 {e_ident,e_type,e_machine} + 24 {e_entry,e_phoff,e_shoff} +
4 {e_flags} = 48 # ^^ See note below.
mask: 20 {e_ident,e_type,e_machine} + 96 {e_entry,e_phoff,e_shoff} +
4 {e_flags} = 120
Remember above we had 107 left over, and now we're at 168. This is of
course the *best* case scenario -- you'll also want to have NUL bytes
in the magic & mask too to match literal zeros.
Note: the reason we can use 24 in the magic is that we can work off of the
fact that for bytes the mask would clobber, we can stuff any value into
magic that we want. So when mask is \x00, we don't need the magic to also
be \x00, it can be an unescaped raw byte like '!'. This lets us handle
more formats (barely) under the current 256 limit, but that's a pretty
tall hoop to force people to jump through.
With all that said, let's bump the limit from 256 bytes to 1920. This way
we support escaping every byte of the mask & magic field (which is 1024
bytes by themselves -- 128 * 4 * 2), and we leave plenty of room for other
fields. Like long paths to the interpreter (when you have source in your
/really/long/homedir/qemu/foo). Since the current code stuffs more than
one structure into the same buffer, we leave a bit of space to easily
round up to 2k. 1920 is just as arbitrary as 256 ;).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- Optimized support for Intel "Cluster-on-Die" (CoD) topologies (Dave
Hansen)
- Various sched/idle refinements for better idle handling (Nicolas
Pitre, Daniel Lezcano, Chuansheng Liu, Vincent Guittot)
- sched/numa updates and optimizations (Rik van Riel)
- sysbench speedup (Vincent Guittot)
- capacity calculation cleanups/refactoring (Vincent Guittot)
- Various cleanups to thread group iteration (Oleg Nesterov)
- Double-rq-lock removal optimization and various refactorings
(Kirill Tkhai)
- various sched/deadline fixes
... and lots of other changes"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (72 commits)
sched/dl: Use dl_bw_of() under rcu_read_lock_sched()
sched/fair: Delete resched_cpu() from idle_balance()
sched, time: Fix build error with 64 bit cputime_t on 32 bit systems
sched: Improve sysbench performance by fixing spurious active migration
sched/x86: Fix up typo in topology detection
x86, sched: Add new topology for multi-NUMA-node CPUs
sched/rt: Use resched_curr() in task_tick_rt()
sched: Use rq->rd in sched_setaffinity() under RCU read lock
sched: cleanup: Rename 'out_unlock' to 'out_free_new_mask'
sched: Use dl_bw_of() under RCU read lock
sched/fair: Remove duplicate code from can_migrate_task()
sched, mips, ia64: Remove __ARCH_WANT_UNLOCKED_CTXSW
sched: print_rq(): Don't use tasklist_lock
sched: normalize_rt_tasks(): Don't use _irqsave for tasklist_lock, use task_rq_lock()
sched: Fix the task-group check in tg_has_rt_tasks()
sched/fair: Leverage the idle state info when choosing the "idlest" cpu
sched: Let the scheduler see CPU idle states
sched/deadline: Fix inter- exclusive cpusets migrations
sched/deadline: Clear dl_entity params when setscheduling to different class
sched/numa: Kill the wrong/dead TASK_DEAD check in task_numa_fault()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core locking updates from Ingo Molnar:
"The main updates in this cycle were:
- mutex MCS refactoring finishing touches: improve comments, refactor
and clean up code, reduce debug data structure footprint, etc.
- qrwlock finishing touches: remove old code, self-test updates.
- small rwsem optimization
- various smaller fixes/cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/lockdep: Revert qrwlock recusive stuff
locking/rwsem: Avoid double checking before try acquiring write lock
locking/rwsem: Move EXPORT_SYMBOL() lines to follow function definition
locking/rwlock, x86: Delete unused asm/rwlock.h and rwlock.S
locking/rwlock, x86: Clean up asm/spinlock*.h to remove old rwlock code
locking/semaphore: Resolve some shadow warnings
locking/selftest: Support queued rwlock
locking/lockdep: Restrict the use of recursive read_lock() with qrwlock
locking/spinlocks: Always evaluate the second argument of spin_lock_nested()
locking/Documentation: Update locking/mutex-design.txt disadvantages
locking/Documentation: Move locking related docs into Documentation/locking/
locking/mutexes: Use MUTEX_SPIN_ON_OWNER when appropriate
locking/mutexes: Refactor optimistic spinning code
locking/mcs: Remove obsolete comment
locking/mutexes: Document quick lock release when unlocking
locking/mutexes: Standardize arguments in lock/unlock slowpaths
locking: Remove deprecated smp_mb__() barriers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU updates from Ingo Molnar:
"The main changes in this cycle were:
- changes related to No-CBs CPUs and NO_HZ_FULL
- RCU-tasks implementation
- torture-test updates
- miscellaneous fixes
- locktorture updates
- RCU documentation updates"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (81 commits)
workqueue: Use cond_resched_rcu_qs macro
workqueue: Add quiescent state between work items
locktorture: Cleanup header usage
locktorture: Cannot hold read and write lock
locktorture: Fix __acquire annotation for spinlock irq
locktorture: Support rwlocks
rcu: Eliminate deadlock between CPU hotplug and expedited grace periods
locktorture: Document boot/module parameters
rcutorture: Rename rcutorture_runnable parameter
locktorture: Add test scenario for rwsem_lock
locktorture: Add test scenario for mutex_lock
locktorture: Make torture scripting account for new _runnable name
locktorture: Introduce torture context
locktorture: Support rwsems
locktorture: Add infrastructure for torturing read locks
torture: Address race in module cleanup
locktorture: Make statistics generic
locktorture: Teach about lock debugging
locktorture: Support mutexes
locktorture: Add documentation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs updates from Al Viro:
"The big thing in this pile is Eric's unmount-on-rmdir series; we
finally have everything we need for that. The final piece of prereqs
is delayed mntput() - now filesystem shutdown always happens on
shallow stack.
Other than that, we have several new primitives for iov_iter (Matt
Wilcox, culled from his XIP-related series) pushing the conversion to
->read_iter()/ ->write_iter() a bit more, a bunch of fs/dcache.c
cleanups and fixes (including the external name refcounting, which
gives consistent behaviour of d_move() wrt procfs symlinks for long
and short names alike) and assorted cleanups and fixes all over the
place.
This is just the first pile; there's a lot of stuff from various
people that ought to go in this window. Starting with
unionmount/overlayfs mess... ;-/"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (60 commits)
fs/file_table.c: Update alloc_file() comment
vfs: Deduplicate code shared by xattr system calls operating on paths
reiserfs: remove pointless forward declaration of struct nameidata
don't need that forward declaration of struct nameidata in dcache.h anymore
take dname_external() into fs/dcache.c
let path_init() failures treated the same way as subsequent link_path_walk()
fix misuses of f_count() in ppp and netlink
ncpfs: use list_for_each_entry() for d_subdirs walk
vfs: move getname() from callers to do_mount()
gfs2_atomic_open(): skip lookups on hashed dentry
[infiniband] remove pointless assignments
gadgetfs: saner API for gadgetfs_create_file()
f_fs: saner API for ffs_sb_create_file()
jfs: don't hash direct inode
[s390] remove pointless assignment of ->f_op in vmlogrdr ->open()
ecryptfs: ->f_op is never NULL
android: ->f_op is never NULL
nouveau: __iomem misannotations
missing annotation in fs/file.c
fs: namespace: suppress 'may be used uninitialized' warnings
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem updates from James Morris.
Mostly ima, selinux, smack and key handling updates.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (65 commits)
integrity: do zero padding of the key id
KEYS: output last portion of fingerprint in /proc/keys
KEYS: strip 'id:' from ca_keyid
KEYS: use swapped SKID for performing partial matching
KEYS: Restore partial ID matching functionality for asymmetric keys
X.509: If available, use the raw subjKeyId to form the key description
KEYS: handle error code encoded in pointer
selinux: normalize audit log formatting
selinux: cleanup error reporting in selinux_nlmsg_perm()
KEYS: Check hex2bin()'s return when generating an asymmetric key ID
ima: detect violations for mmaped files
ima: fix race condition on ima_rdwr_violation_check and process_measurement
ima: added ima_policy_flag variable
ima: return an error code from ima_add_boot_aggregate()
ima: provide 'ima_appraise=log' kernel option
ima: move keyring initialization to ima_init()
PKCS#7: Handle PKCS#7 messages that contain no X.509 certs
PKCS#7: Better handling of unsupported crypto
KEYS: Overhaul key identification when searching for asymmetric keys
KEYS: Implement binary asymmetric key ID handling
...
|
|
Pull networking fixes from David Miller:
"This set fixes a bunch of fallout from the changes that went in during
this merge window, particularly:
- Fix fsl_pq_mdio (Claudiu Manoil) and fm10k (Pranith Kumar) build
failures.
- Several networking drivers do atomic_set() on page counts where
that's not exactly legal. From Eric Dumazet.
- Make __skb_flow_get_ports() work cleanly with unaligned data, from
Alexander Duyck.
- Fix some kernel-doc buglets in rfkill and netlabel, from Fabian
Frederick.
- Unbalanced enable_irq_wake usage in bcmgenet and systemport
drivers, from Florian Fainelli.
- pxa168_eth needs to depend on HAS_DMA, from Geert Uytterhoeven.
- Multi-dequeue in the qdisc layer severely bypasses the fairness
limits the previous code used to enforce, reintroduce in a way that
at the same time doesn't compromise bulk dequeue opportunities.
From Jesper Dangaard Brouer.
- macvlan receive path unnecessarily hops through a softirq by using
netif_rx() instead of netif_receive_skb(). From Jason Baron"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (51 commits)
net: systemport: avoid unbalanced enable_irq_wake calls
net: bcmgenet: avoid unbalanced enable_irq_wake calls
net: bcmgenet: fix off-by-one in incrementing read pointer
net: fix races in page->_count manipulation
mlx4: fix race accessing page->_count
ixgbe: fix race accessing page->_count
igb: fix race accessing page->_count
fm10k: fix race accessing page->_count
net/phy: micrel: Add clock support for KSZ8021/KSZ8031
flow-dissector: Fix alignment issue in __skb_flow_get_ports
net: filter: fix the comments
Documentation: replace __sk_run_filter with __bpf_prog_run
macvlan: optimize the receive path
macvlan: pass 'bool' type to macvlan_count_rx()
drivers: net: xgene: Add 10GbE ethtool support
drivers: net: xgene: Add 10GbE support
drivers: net: xgene: Preparing for adding 10GbE support
dtb: Add 10GbE node to APM X-Gene SoC device tree
Documentation: dts: Update section header for APM X-Gene
MAINTAINERS: Update APM X-Gene section
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
"Here's a first pull request for powerpc updates for 3.18.
The bulk of the additions are for the "cxl" driver, for IBM's Coherent
Accelerator Processor Interface (CAPI). Most of it's in drivers/misc,
which Greg & Arnd maintain, Greg said he was happy for us to take it
through our tree.
There's the usual minor cleanups and fixes, including a bit of noise
in drivers from some of those. A bunch of updates to our EEH code,
which has been getting more testing. Several nice speedups from
Anton, including 20% in clear_page().
And a bunch of updates for freescale from Scott"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (130 commits)
cxl: Fix afu_read() not doing finish_wait() on signal or non-blocking
cxl: Add documentation for userspace APIs
cxl: Add driver to Kbuild and Makefiles
cxl: Add userspace header file
cxl: Driver code for powernv PCIe based cards for userspace access
cxl: Add base builtin support
powerpc/mm: Add hooks for cxl
powerpc/opal: Add PHB to cxl mode call
powerpc/mm: Add new hash_page_mm()
powerpc/powerpc: Add new PCIe functions for allocating cxl interrupts
cxl: Add new header for call backs and structs
powerpc/powernv: Split out set MSI IRQ chip code
powerpc/mm: Export mmu_kernel_ssize and mmu_linear_psize
powerpc/msi: Improve IRQ bitmap allocator
powerpc/cell: Make spu_flush_all_slbs() generic
powerpc/cell: Move data segment faulting code out of cell platform
powerpc/cell: Move spu_handle_mm_fault() out of cell platform
powerpc/pseries: Use new defines when calling H_SET_MODE
powerpc: Update contact info in Documentation files
powerpc/perf/hv-24x7: Simplify catalog_read()
...
|
|
Active multiplexing is a nice feature as it allows several pointing devices
(such as touchpad and external mouse) use their native protocols at the
same time. Unfortunately many manufacturers do not implement the feature
properly even though they advertise it. The problematic implementations are
never fixed, since Windows by default does not use this mode, and move from
one BIOS/model of laptop to another. When active multiplexing is broken
turning it on usually results in touchpad, keyboard, or both unresponsive.
With PS/2 usage on decline (most of PS/2 devices in use nowadays are
internal laptop touchpads), I expect number of users who have laptops with
working MUX implementation, docking stations with external PS/2 ports, and
who are still using external PS/2 mice, to be rather small. Let's flip the
default to be OFF and allow activating it through i8042.nomux=0 kernel
option. We'll also keep DMI table where we can record known good models.
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
