| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This is the 5.0.14 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
commit c2b71462d294cf517a0bc6e4fd6424d7cee5596f upstream.
The syzkaller fuzzer reported a bug in the USB hub driver which turned
out to be caused by a negative runtime-PM usage counter. This allowed
a hub to be runtime suspended at a time when the driver did not expect
it. The symptom is a WARNING issued because the hub's status URB is
submitted while it is already active:
URB 0000000031fb463e submitted while active
WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363
The negative runtime-PM usage count was caused by an unfortunate
design decision made when runtime PM was first implemented for USB.
At that time, USB class drivers were allowed to unbind from their
interfaces without balancing the usage counter (i.e., leaving it with
a positive count). The core code would take care of setting the
counter back to 0 before allowing another driver to bind to the
interface.
Later on when runtime PM was implemented for the entire kernel, the
opposite decision was made: Drivers were required to balance their
runtime-PM get and put calls. In order to maintain backward
compatibility, however, the USB subsystem adapted to the new
implementation by keeping an independent usage counter for each
interface and using it to automatically adjust the normal usage
counter back to 0 whenever a driver was unbound.
This approach involves duplicating information, but what is worse, it
doesn't work properly in cases where a USB class driver delays
decrementing the usage counter until after the driver's disconnect()
routine has returned and the counter has been adjusted back to 0.
Doing so would cause the usage counter to become negative. There's
even a warning about this in the USB power management documentation!
As it happens, this is exactly what the hub driver does. The
kick_hub_wq() routine increments the runtime-PM usage counter, and the
corresponding decrement is carried out by hub_event() in the context
of the hub_wq work-queue thread. This work routine may sometimes run
after the driver has been unbound from its interface, and when it does
it causes the usage counter to go negative.
It is not possible for hub_disconnect() to wait for a pending
hub_event() call to finish, because hub_disconnect() is called with
the device lock held and hub_event() acquires that lock. The only
feasible fix is to reverse the original design decision: remove the
duplicate interface-specific usage counter and require USB drivers to
balance their runtime PM gets and puts. As far as I know, all
existing drivers currently do this.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the 5.0.13 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
[ Upstream commit 5cd1c56c42beb6d228cc8d4373fdc5f5ec78a5ad ]
Add PCI ID for Intel Comet Lake PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
|
|
This is the 5.0.11 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
[ Upstream commit 19fad20d15a6494f47f85d869f00b11343ee5c78 ]
There is a UBSAN report as below:
UBSAN: Undefined behaviour in net/ipv4/tcp_input.c:2877:56
signed integer overflow:
2147483647 * 1000 cannot be represented in type 'int'
CPU: 3 PID: 0 Comm: swapper/3 Not tainted 5.1.0-rc4-00058-g582549e #1
Call Trace:
<IRQ>
dump_stack+0x8c/0xba
ubsan_epilogue+0x11/0x60
handle_overflow+0x12d/0x170
? ttwu_do_wakeup+0x21/0x320
__ubsan_handle_mul_overflow+0x12/0x20
tcp_ack_update_rtt+0x76c/0x780
tcp_clean_rtx_queue+0x499/0x14d0
tcp_ack+0x69e/0x1240
? __wake_up_sync_key+0x2c/0x50
? update_group_capacity+0x50/0x680
tcp_rcv_established+0x4e2/0xe10
tcp_v4_do_rcv+0x22b/0x420
tcp_v4_rcv+0xfe8/0x1190
ip_protocol_deliver_rcu+0x36/0x180
ip_local_deliver+0x15b/0x1a0
ip_rcv+0xac/0xd0
__netif_receive_skb_one_core+0x7f/0xb0
__netif_receive_skb+0x33/0xc0
netif_receive_skb_internal+0x84/0x1c0
napi_gro_receive+0x2a0/0x300
receive_buf+0x3d4/0x2350
? detach_buf_split+0x159/0x390
virtnet_poll+0x198/0x840
? reweight_entity+0x243/0x4b0
net_rx_action+0x25c/0x770
__do_softirq+0x19b/0x66d
irq_exit+0x1eb/0x230
do_IRQ+0x7a/0x150
common_interrupt+0xf/0xf
</IRQ>
It can be reproduced by:
echo 2147483647 > /proc/sys/net/ipv4/tcp_min_rtt_wlen
Fixes: f672258391b42 ("tcp: track min RTT using windowed min-filter")
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
model
commit 24512228b7a3f412b5a51f189df302616b021c33 upstream.
Mikulas Patocka reported that commit 1c30844d2dfe ("mm: reclaim small
amounts of memory when an external fragmentation event occurs") "broke"
memory management on parisc.
The machine is not NUMA but the DISCONTIG model creates three pgdats
even though it's a UMA machine for the following ranges
0) Start 0x0000000000000000 End 0x000000003fffffff Size 1024 MB
1) Start 0x0000000100000000 End 0x00000001bfdfffff Size 3070 MB
2) Start 0x0000004040000000 End 0x00000040ffffffff Size 3072 MB
Mikulas reported:
With the patch 1c30844d2, the kernel will incorrectly reclaim the
first zone when it fills up, ignoring the fact that there are two
completely free zones. Basiscally, it limits cache size to 1GiB.
For example, if I run:
# dd if=/dev/sda of=/dev/null bs=1M count=2048
- with the proper kernel, there should be "Buffers - 2GiB"
when this command finishes. With the patch 1c30844d2, buffers
will consume just 1GiB or slightly more, because the kernel was
incorrectly reclaiming them.
The page allocator and reclaim makes assumptions that pgdats really
represent NUMA nodes and zones represent ranges and makes decisions on
that basis. Watermark boosting for small pgdats leads to unexpected
results even though this would have behaved reasonably on SPARSEMEM.
DISCONTIG is essentially deprecated and even parisc plans to move to
SPARSEMEM so there is no need to be fancy, this patch simply disables
watermark boosting by default on DISCONTIGMEM.
Link: http://lkml.kernel.org/r/20190419094335.GJ18914@techsingularity.net
Fixes: 1c30844d2dfe ("mm: reclaim small amounts of memory when an external fragmentation event occurs")
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The isl68137 is a digital output 7-phrase configurable PWM controller
with an AVSBus interface from Intersil.
OpenBMC-Staging-Count: 1
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The ir38064 is a voltage regulator from Infineon.
OpenBMC-Staging-Count: 1
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Document the ast2400, ast2500 PCI-to-AHB bridge control driver bindings.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 28703c6ef6228635f7c8b248c1d846511a2b60a3)
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Apply differences from hwmon review to bring the driver code to the same
point. There were some key differences regarding attribute placement
from the review, beyond the normal cleanup.
OpenBMC-Staging-Count: 1
Signed-off-by: Patrick Venture <venture@google.com>
[AJ: Rework subject]
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
|
|
Added device tree binding documentation for Nuvoton BMC
NPCM Platform Environment Control Interface(PECI).
OpenBMC-Staging-Count: 1
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This is the 5.0.7 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
[ Upstream commit de9c0d49d85dc563549972edc5589d195cd5e859 ]
While building arm32 allyesconfig, I ran into the following errors:
arch/arm/lib/xor-neon.c:17:2: error: You should compile this file with
'-mfloat-abi=softfp -mfpu=neon'
In file included from lib/raid6/neon1.c:27:
/home/nathan/cbl/prebuilt/lib/clang/8.0.0/include/arm_neon.h:28:2:
error: "NEON support not enabled"
Building V=1 showed NEON_FLAGS getting passed along to Clang but
__ARM_NEON__ was not getting defined. Ultimately, it boils down to Clang
only defining __ARM_NEON__ when targeting armv7, rather than armv6k,
which is the '-march' value for allyesconfig.
>From lib/Basic/Targets/ARM.cpp in the Clang source:
// This only gets set when Neon instructions are actually available, unlike
// the VFP define, hence the soft float and arch check. This is subtly
// different from gcc, we follow the intent which was that it should be set
// when Neon instructions are actually available.
if ((FPU & NeonFPU) && !SoftFloat && ArchVersion >= 7) {
Builder.defineMacro("__ARM_NEON", "1");
Builder.defineMacro("__ARM_NEON__");
// current AArch32 NEON implementations do not support double-precision
// floating-point even when it is present in VFP.
Builder.defineMacro("__ARM_NEON_FP",
"0x" + Twine::utohexstr(HW_FP & ~HW_FP_DP));
}
Ard Biesheuvel recommended explicitly adding '-march=armv7-a' at the
beginning of the NEON_FLAGS definitions so that __ARM_NEON__ always gets
definined by Clang. This doesn't functionally change anything because
that code will only run where NEON is supported, which is implicitly
armv7.
Link: https://github.com/ClangBuiltLinux/linux/issues/287
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Missed documenting this property in the initial commit.
OpenBMC-Staging-Count: 1
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This is the 5.0.6 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
commit ddba91801aeb5c160b660caed1800eb3aef403f8 upstream.
KVM's API requires thats ioctls must be issued from the same process
that created the VM. In other words, userspace can play games with a
VM's file descriptors, e.g. fork(), SCM_RIGHTS, etc..., but only the
creator can do anything useful. Explicitly reject device ioctls that
are issued by a process other than the VM's creator, and update KVM's
API documentation to extend its requirements to device ioctls.
Fixes: 852b6d57dc7f ("kvm: add device control API")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the 5.0.4 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
commit a41e8f25fa8f8f67360d88eb0eebbabe95a64bdf upstream.
The networking maintainer keeps a public list of the patches being
queued up for the next round of stable releases. Be sure to check there
before asking for a patch to be applied so that you do not waste
people's time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 133d624b1cee16906134e92d5befb843b58bcf31 upstream.
The function returns the maximum size that can be mapped
using DMA-API functions. The patch also adds the
implementation for direct DMA and a new dma_map_ops pointer
so that other implementations can expose their limit.
Cc: stable@vger.kernel.org
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c950ca8c35eeb32224a63adc47e12f9e226da241 upstream.
The Allwinner A64 SoC is known[1] to have an unstable architectural
timer, which manifests itself most obviously in the time jumping forward
a multiple of 95 years[2][3]. This coincides with 2^56 cycles at a
timer frequency of 24 MHz, implying that the time went slightly backward
(and this was interpreted by the kernel as it jumping forward and
wrapping around past the epoch).
Investigation revealed instability in the low bits of CNTVCT at the
point a high bit rolls over. This leads to power-of-two cycle forward
and backward jumps. (Testing shows that forward jumps are about twice as
likely as backward jumps.) Since the counter value returns to normal
after an indeterminate read, each "jump" really consists of both a
forward and backward jump from the software perspective.
Unless the kernel is trapping CNTVCT reads, a userspace program is able
to read the register in a loop faster than it changes. A test program
running on all 4 CPU cores that reported jumps larger than 100 ms was
run for 13.6 hours and reported the following:
Count | Event
-------+---------------------------
9940 | jumped backward 699ms
268 | jumped backward 1398ms
1 | jumped backward 2097ms
16020 | jumped forward 175ms
6443 | jumped forward 699ms
2976 | jumped forward 1398ms
9 | jumped forward 356516ms
9 | jumped forward 357215ms
4 | jumped forward 714430ms
1 | jumped forward 3578440ms
This works out to a jump larger than 100 ms about every 5.5 seconds on
each CPU core.
The largest jump (almost an hour!) was the following sequence of reads:
0x0000007fffffffff → 0x00000093feffffff → 0x0000008000000000
Note that the middle bits don't necessarily all read as all zeroes or
all ones during the anomalous behavior; however the low 10 bits checked
by the function in this patch have never been observed with any other
value.
Also note that smaller jumps are much more common, with backward jumps
of 2048 (2^11) cycles observed over 400 times per second on each core.
(Of course, this is partially explained by lower bits rolling over more
frequently.) Any one of these could have caused the 95 year time skip.
Similar anomalies were observed while reading CNTPCT (after patching the
kernel to allow reads from userspace). However, the CNTPCT jumps are
much less frequent, and only small jumps were observed. The same program
as before (except now reading CNTPCT) observed after 72 hours:
Count | Event
-------+---------------------------
17 | jumped backward 699ms
52 | jumped forward 175ms
2831 | jumped forward 699ms
5 | jumped forward 1398ms
Further investigation showed that the instability in CNTPCT/CNTVCT also
affected the respective timer's TVAL register. The following values were
observed immediately after writing CNVT_TVAL to 0x10000000:
CNTVCT | CNTV_TVAL | CNTV_CVAL | CNTV_TVAL Error
--------------------+------------+--------------------+-----------------
0x000000d4a2d8bfff | 0x10003fff | 0x000000d4b2d8bfff | +0x00004000
0x000000d4a2d94000 | 0x0fffffff | 0x000000d4b2d97fff | -0x00004000
0x000000d4a2d97fff | 0x10003fff | 0x000000d4b2d97fff | +0x00004000
0x000000d4a2d9c000 | 0x0fffffff | 0x000000d4b2d9ffff | -0x00004000
The pattern of errors in CNTV_TVAL seemed to depend on exactly which
value was written to it. For example, after writing 0x10101010:
CNTVCT | CNTV_TVAL | CNTV_CVAL | CNTV_TVAL Error
--------------------+------------+--------------------+-----------------
0x000001ac3effffff | 0x1110100f | 0x000001ac4f10100f | +0x1000000
0x000001ac40000000 | 0x1010100f | 0x000001ac5110100f | -0x1000000
0x000001ac58ffffff | 0x1110100f | 0x000001ac6910100f | +0x1000000
0x000001ac66000000 | 0x1010100f | 0x000001ac7710100f | -0x1000000
0x000001ac6affffff | 0x1110100f | 0x000001ac7b10100f | +0x1000000
0x000001ac6e000000 | 0x1010100f | 0x000001ac7f10100f | -0x1000000
I was also twice able to reproduce the issue covered by Allwinner's
workaround[4], that writing to TVAL sometimes fails, and both CVAL and
TVAL are left with entirely bogus values. One was the following values:
CNTVCT | CNTV_TVAL | CNTV_CVAL
--------------------+------------+--------------------------------------
0x000000d4a2d6014c | 0x8fbd5721 | 0x000000d132935fff (615s in the past)
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
========================================================================
Because the CPU can read the CNTPCT/CNTVCT registers faster than they
change, performing two reads of the register and comparing the high bits
(like other workarounds) is not a workable solution. And because the
timer can jump both forward and backward, no pair of reads can
distinguish a good value from a bad one. The only way to guarantee a
good value from consecutive reads would be to read _three_ times, and
take the middle value only if the three values are 1) each unique and
2) increasing. This takes at minimum 3 counter cycles (125 ns), or more
if an anomaly is detected.
However, since there is a distinct pattern to the bad values, we can
optimize the common case (1022/1024 of the time) to a single read by
simply ignoring values that match the error pattern. This still takes no
more than 3 cycles in the worst case, and requires much less code. As an
additional safety check, we still limit the loop iteration to the number
of max-frequency (1.2 GHz) CPU cycles in three 24 MHz counter periods.
For the TVAL registers, the simple solution is to not use them. Instead,
read or write the CVAL and calculate the TVAL value in software.
Although the manufacturer is aware of at least part of the erratum[4],
there is no official name for it. For now, use the kernel-internal name
"UNKNOWN1".
[1]: https://github.com/armbian/build/commit/a08cd6fe7ae9
[2]: https://forum.armbian.com/topic/3458-a64-datetime-clock-issue/
[3]: https://irclog.whitequark.org/linux-sunxi/2018-01-26
[4]: https://github.com/Allwinner-Homlet/H6-BSP4.9-linux/blob/master/drivers/clocksource/arm_arch_timer.c#L272
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 103cda6a3b8d2c10d5f8cd7abad118e9db8f4776 upstream.
Exynos4212 and Exynos4412 have only four ADC channels so using
"samsung,exynos-adc-v1" compatible (for eight channels ADCv1) on them is
wrong. Add a new compatible for Exynos4x12.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added device tree binding documentation for Nuvoton BMC
NPCM Analog-to-Digital Converter(ADC).
OpenBMC-Staging-Count: 2
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
[include dt-binding: iio: npcm-adc: Fix whitespace]
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Added device tree binding documentation for
Nuvoton NPCM7xx Ethernet MAC Controller (EMC).
OpenBMC-Staging-Count: 2
Signed-off-by: Avi Fishman <avifishman70@gmail.com>
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Added device tree binding documentation for Nuvoton BMC
NPCM7XX PCI mailbox.
OpenBMC-Staging-Count: 2
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Added device tree binding documentation for Nuvoton BMC
NPCM7xx BIOS Post Code (BPC).
The NPCM7xx BPC monitoring two configurable I/O addresses
written by the host on Low Pin Count (LPC) bus.
OpenBMC-Staging-Count: 2
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
OpenBMC-Staging-Count: 2
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Added device tree binding documentation for Nuvoton BMC
NPCM Flash Interface Unit(FIU) SPI-NOR controller.
OpenBMC-Staging-Count: 2
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This commit adds hwmon documents for PECI cputemp and dimmtemp drivers.
OpenBMC-Staging-Count: 2
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Haiyue Wang <haiyue.wang@linux.intel.com>
Reviewed-by: James Feist <james.feist@linux.intel.com>
Reviewed-by: Vernon Mauery <vernon.mauery@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This commit adds a dt-bindings document for PECI client MFD.
OpenBMC-Staging-Count: 2
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This commit adds a dt-bindings document of PECI adapter driver for ASPEED
AST24xx/25xx SoCs.
OpenBMC-Staging-Count: 2
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Haiyue Wang <haiyue.wang@linux.intel.com>
Reviewed-by: James Feist <james.feist@linux.intel.com>
Reviewed-by: Vernon Mauery <vernon.mauery@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This commit updates ioctl-number.txt to reflect ioctl numbers used
by the PECI subsystem.
OpenBMC-Staging-Count: 2
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This commit adds a document of generic PECI bus, adapter and client
driver.
OpenBMC-Staging-Count: 2
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Haiyue Wang <haiyue.wang@linux.intel.com>
Reviewed-by: James Feist <james.feist@linux.intel.com>
Reviewed-by: Vernon Mauery <vernon.mauery@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
For security reasons, some configuration needs to run without /dev/mem
but on some occasions, to debug HW for instance, it's still useful to
be able to reboot the system with access to physical memory.
Add a kernel parameter which activates the /dev/mem device only when
'mem.devmem' is enabled.
OpenBMC-Staging-Count: 3
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Describe the RTC as used in the ASPEED ast2400 and ast2500 SoCs.
OpenBMC-Staging-Count: 3
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This describes the ASPEED BMC SoC's display controller.
OpenBMC-Staging-Count: 4
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
OpenBMC-Staging-Count: 6
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Pull networking fixes from David Miller:
"Hopefully the last pull request for this release. Fingers crossed:
1) Only refcount ESP stats on full sockets, from Martin Willi.
2) Missing barriers in AF_UNIX, from Al Viro.
3) RCU protection fixes in ipv6 route code, from Paolo Abeni.
4) Avoid false positives in untrusted GSO validation, from Willem de
Bruijn.
5) Forwarded mesh packets in mac80211 need more tailroom allocated,
from Felix Fietkau.
6) Use operstate consistently for linkup in team driver, from George
Wilkie.
7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
and PF code paths.
8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.
9) nfp eBPF code gen fixes from Jiong Wang.
10) bnxt_en firmware timeout fix from Michael Chan.
11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.
12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
net: phy: realtek: Dummy IRQ calls for RTL8366RB
tcp: repaired skbs must init their tso_segs
net/x25: fix a race in x25_bind()
net: dsa: Remove documentation for port_fdb_prepare
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
selftests: fib_tests: sleep after changing carrier. again.
net: set static variable an initial value in atl2_probe()
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
bpf, doc: add bpf list as secondary entry to maintainers file
udp: fix possible user after free in error handler
udpv6: fix possible user after free in error handler
fou6: fix proto error handler argument type
udpv6: add the required annotation to mib type
mdio_bus: Fix use-after-free on device_register fails
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
bnxt_en: Wait longer for the firmware message response to complete.
bnxt_en: Fix typo in firmware message timeout logic.
nfp: bpf: fix ALU32 high bits clearance bug
nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
Documentation: networking: switchdev: Update port parent ID section
...
|
|
This callback was removed some time ago, also remove the documentation.
Fixes: 1b6dd556c304 ("net: dsa: Remove prepare phase for FDB")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the section about switchdev drivers having to implement a
switchdev_port_attr_get() function to return
SWITCHDEV_ATTR_ID_PORT_PARENT_ID since that is no longer valid after
commit bccb30254a4a ("net: Get rid of
SWITCHDEV_ATTR_ID_PORT_PARENT_ID").
Fixes: bccb30254a4a ("net: Get rid of SWITCHDEV_ATTR_ID_PORT_PARENT_ID")
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull documentation fix from Jonathan Corbet:
"A single patch from Arnd bringing some top-level docs into the 5.0
era"
* tag 'docs-5.0-fix' of git://git.lwn.net/linux:
Documentation: change linux-4.x references to 5.x
|
|
MSG_ZEROCOPY implementation for UDP was merged in v5.0,
6e360f733113 ("Merge branch 'udp-msg_zerocopy'").
Signed-off-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As linux-5.0.x is coming up soon, the documentation should match,
in particular the README.rst file, so change all 4.x references
accordingly. There was a mix of lowercase and uppercase X here,
which I changed to using lowercase consistently.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Pull networking fixes from David Miller:
1) Fix MAC address setting in mac80211 pmsr code, from Johannes Berg.
2) Probe SFP modules after being attached, from Russell King.
3) Byte ordering bug in SMC rx_curs_confirmed code, from Ursula Braun.
4) Revert some r8169 changes that are causing regressions, from Heiner
Kallweit.
5) Fix spurious connection timeouts in netfilter nat code, from Florian
Westphal.
6) SKB leak in tipc, from Hoang Le.
7) Short packet checkum issue in mlx4, similar to a previous mlx5
change, from Saeed Mahameed. The issue is that whilst padding bytes
are usually zero, it is not guarateed and the hardware doesn't take
the padding bytes into consideration when generating the checksum.
8) Fix various races in cls_tcindex, from Cong Wang.
9) Need to set stream ext to NULL before freeing in SCTP code, from Xin
Long.
10) Fix locking in phy_is_started, from Heiner Kallweit.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
net: ethernet: freescale: set FEC ethtool regs version
net: hns: Fix object reference leaks in hns_dsaf_roce_reset()
mm: page_alloc: fix ref bias in page_frag_alloc() for 1-byte allocs
net: phy: fix potential race in the phylib state machine
net: phy: don't use locking in phy_is_started
selftests: fix timestamping Makefile
net: dsa: bcm_sf2: potential array overflow in bcm_sf2_sw_suspend()
net: fix possible overflow in __sk_mem_raise_allocated()
dsa: mv88e6xxx: Ensure all pending interrupts are handled prior to exit
net: phy: fix interrupt handling in non-started states
sctp: set stream ext to NULL after freeing it in sctp_stream_outq_migrate
sctp: call gso_reset_checksum when computing checksum in sctp_gso_segment
net/mlx5e: XDP, fix redirect resources availability check
net/mlx5: Fix a compilation warning in events.c
net/mlx5: No command allowed when command interface is not ready
net/mlx5e: Fix NULL pointer derefernce in set channels error flow
netfilter: nft_compat: use-after-free when deleting targets
team: avoid complex list operations in team_nl_cmd_options_set()
net_sched: fix two more memory leaks in cls_tcindex
net_sched: fix a memory leak in cls_tcindex
...
|
|
Netlink has moved from bitmasks to group numbers long ago.
Signed-off-by: Jouke Witteveen <j.witteveen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a grammatical error in the dentry-state text and clarify the usage
of negative dentries.
Fixes: af0c9af1b3f66 ("fs/dcache: Track & report number of negative dentries")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"Intel decided to leave the newly added Scalable Mode Feature
default-disabled for now. The patch here accomplishes that"
* tag 'iommu-fixes-v5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Leave scalable mode default off
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixlet from Darren Hart:
"Correct Documentation/ABI 4.21 KernelVersion to 5.0"
* tag 'platform-drivers-x86-v5.0-2' of git://git.infradead.org/linux-platform-drivers-x86:
Documentation/ABI: Correct mlxreg-io KernelVersion for 5.0
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A few updates for x86:
- Fix an unintended sign extension issue in the fault handling code
- Rename the new resource control config switch so it's less
confusing
- Avoid setting up EFI info in kexec when the EFI runtime is
disabled.
- Fix the microcode version check in the AMD microcode loader so it
only loads higher version numbers and never downgrades
- Set EFER.LME in the 32bit trampoline before returning to long mode
to handle older AMD/KVM behaviour properly.
- Add Darren and Andy as x86/platform reviewers"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/resctrl: Avoid confusion over the new X86_RESCTRL config
x86/kexec: Don't setup EFI info if EFI runtime is not enabled
x86/microcode/amd: Don't falsely trick the late loading mechanism
MAINTAINERS: Add Andy and Darren as arch/x86/platform/ reviewers
x86/fault: Fix sign-extend unintended sign extension
x86/boot/compressed/64: Set EFER.LME=1 in 32-bit trampoline before returning to long mode
x86/cpu: Add Atom Tremont (Jacobsville)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fix from Rob Herring:
"A single fix for building DT bindings in-tree"
* tag 'devicetree-fixes-for-5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: Fix dt_binding_check target for in tree builds
|
