| Age | Commit message (Collapse) | Author | Files | Lines |
|
The MediaTek 0.96 xHCI controller on some platforms does not
support bulk stream even HCCPARAMS says supporting, due to MaxPSASize
is set a default value 1 by mistake, here use XHCI_BROKEN_STREAMS
quirk to fix it.
Fixes: 94a631d91ad3 ("usb: xhci-mtk: check hcc_params after adding primary hcd")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-4-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ensure that dep->flags are cleared until after stop active transfers
is completed. Otherwise, the ENDXFER command will not be executed
during ep disable.
Fixes: f09ddcfcb8c5 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers")
Cc: stable <stable@vger.kernel.org>
Reported-and-tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1616610664-16495-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix shift out-of-bounds in vhci_hub_control() SetPortFeature handling.
UBSAN: shift-out-of-bounds in drivers/usb/usbip/vhci_hcd.c:605:42
shift exponent 768 is too large for 32-bit type 'int'
Reported-by: syzbot+3dea30b047f41084de66@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210324230654.34798-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver can match only the devices created by the OF core
via the DT table, so the table should be always used.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-12-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add add support ip-sleep wakeup for MT8192, it's a specific
revision, not following IPM rule.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-11-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support ip-sleep wakeup for MT8183, it's similar to MT8173,
and it's also a specific one, but not following IPM rule.
Due to the index 2 already used by many DTS, it's better to keep
it unchanged for backward compatibility, treat specific ones without
following IPM rule as revision 1.x, meanwhile reserve 3~10 for later
revision that follows the IPM rule.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-10-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support ip-sleep wakeup for mT8192, it's a specific revision,
and not following IPM rule.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-7-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support ip-sleep wakeup for MT8183, it's similar to MT8173,
and it's also a specific one, but not following IPM rule.
Due to the index 2 already used by many DTS, it's better to keep
it unchanged for backward compatibility, treat specific ones without
following IPM rule as revision 1.x, meanwhile reserve 3~10 for
later revision that follows the IPM rule.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-6-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unify quirks, in particular one for Intel Quark, to use driver data
and accompanying infrastructure.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210325135508.70350-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We don't need DMI to identify Intel Minnowboard (v1) since it has
properly set PCI sub IDs. So, drop unneeded DMI level of identification.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210325135508.70350-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use __maybe_unused for the suspend()/resume() hooks and get rid of
the CONFIG_PM_SLEEP ifdefery to improve the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210325135508.70350-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We have generic implementations for a reason, let's use them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210325135508.70350-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A short packet indicates the end of a transfer and marks the request as
complete.
Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-8-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Before this, it wrote as much as available into the buffer, even if it
didn't fit.
Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-7-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Notify the UDC core that a bus reset occurred.
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-6-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently it leaves unhandled interrupts unmasked, but those are never
acked. In the case of a "device idle" interrupt, this leads to an
effectively frozen system until plugging it in.
Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-5-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the EP0 IN request was not completed but less than a packet sent,
it would complete the request successfully. That doesn't make sense
and can't really happen as fotg210_start_dma always sends
min(length, maxpkt) bytes.
Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-4-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For a 134 Byte packet, it sends the first two 64 Byte packets just fine,
but then notice that less than a packet is remaining and call fotg210_done
without actually sending the rest.
Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-3-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For a 75 Byte request, it would send the first 64 separately, then detect
that the remaining 11 Byte fit into a single DMA, but due to this bug set
the length to the original 75 Bytes. This leads to a DMA failure (which is
ignored...) and the request completes without the remaining bytes having
been sent.
Fixes: b84a8dee23fd ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-2-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the compatible string for sc7280 SoC from Qualcomm.
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1615978901-4202-2-git-send-email-sanm@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the L2 driver detects a device crash or device undergone reset, it
invokes a stop callback to recover from error.
The current RoCE driver doesn't recover the device. So move the device to
error state and dispatch fatal events to all qps Release the MSIx vectors
to avoid a crash when L2 driver disables the MSIx. Also, check for the
device state to avoid posting further commands to the HW.
Link: https://lore.kernel.org/r/1615968942-30970-1-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Naresh Kumar PBS <nareshkumar.pbs@broadcom.com>
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Currently dwc3 only prints the virtual address of a register when doing
register read/write. However, these hashed addresses are difficult to read.
Also, since we use %p, we may get some useless (___ptrval___) prints if the
address is not randomized enough. Let's include the register offset to help
read the register read and write tracepoints.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/cb38aa7dec109a8965691b53039a8b317d026189.1616636706.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sparse tool complains as follows:
drivers/usb/typec/tcpm/tcpci_maxim.c:55:34: warning:
symbol 'max_tcpci_tcpci_write_table' was not declared. Should it be static?
This symbol is not used outside of tcpci_maxim.c, so this
commit marks it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210324144253.1011234-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The option '-d/--device' was implemented in 'usbip list' but not
shown in usage. Hence this commit adds this option to usage.
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hongren Zheng <i@zenithal.me>
Link: https://lore.kernel.org/r/YFrwq75Uyef3c9gz@Sun
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commit e0546fd8b748 ("usbip: tools: Start using VUDC backend in
usbip tools") implemented device mode for user space tools, however the
corresponding options are not documented in man page.
This commit documents the options and provides examples on device mode.
Also the command `usbip port` is documented.
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hongren Zheng <i@zenithal.me>
Link: https://lore.kernel.org/r/YFrdyKKx1nx8bktm@Sun
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In list.h, the kernel-doc for list_del() should be immediately
preceding the implementation and not separated from it by
another function implementation.
Eliminates this kernel-doc error:
list.h:1: warning: 'list_del' not found
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210325174724.14447-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
s/Acknowlege/Acknowledge/
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Link: https://lore.kernel.org/r/20210325051023.27914-1-unixbhaskar@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Acer A500 uses Atmel Maxtouch 1386 touchscreen controller. This controller
has WAKE line which could be connected to I2C clock lane, dedicated GPIO
or fixed to HIGH level. Controller wakes up from a deep sleep when WAKE
line is asserted low. Acer A500 has WAKE line connected to I2C clock and
Linux device driver doesn't work property without knowing what wakeup
method is used by h/w.
Add atmel,wakeup-method property to the touchscreen node.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[treding@nvidia.com: use literal to avoid dependency on header file]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
For AES256 encryption (GCM and CCM), we need to adjust the size of a few
fields to 32 bytes instead of 16 to accommodate the larger keys.
Also, the L value supplied to the key generator needs to be changed from
to 256 when these algorithms are used.
Keeping the ioctl struct for dumping keys of the same size for now.
Will send out a different patch for that one.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
CC: <stable@vger.kernel.org> # v5.10+
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Current code uses many different types when dealing with a port of a RDMA
device: u8, unsigned int and u32. Switch to u32 to clean up the logic.
This allows us to make (at least) the core view consistent and use the
same type. Unfortunately not all places can be converted. Many uverbs
functions expect port to be u8 so keep those places in order not to break
UAPIs. HW/Spec defined values must also not be changed.
With the switch to u32 we now can support devices with more than 255
ports. U32_MAX is reserved to make control logic a bit easier to deal
with. As a device with U32_MAX ports probably isn't going to happen any
time soon this seems like a non issue.
When a device with more than 255 ports is created uverbs will report the
RDMA device as having 255 ports as this is the max currently supported.
The verbs interface is not changed yet because the IBTA spec limits the
port size in too many places to be u8 and all applications that relies in
verbs won't be able to cope with this change. At this stage, we are
extending the interfaces that are using vendor channel solely
Once the limitation is lifted mlx5 in switchdev mode will be able to have
thousands of SFs created by the device. As the only instance of an RDMA
device that reports more than 255 ports will be a representor device and
it exposes itself as a RAW Ethernet only device CM/MAD/IPoIB and other
ULPs aren't effected by this change and their sysfs/interfaces that are
exposes to userspace can remain unchanged.
While here cleanup some alignment issues and remove unneeded sanity
checks (mainly in rdmavt),
Link: https://lore.kernel.org/r/20210301070420.439400-1-leon@kernel.org
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
c6f5d02b6a0f (locking/spinlocks/arm64: Remove smp_mb() from
arch_spin_is_locked()) made it pretty official that the call
semantics do not imply any sort of barriers, and any user that
gets creative must explicitly do any serialization.
This creativity, however, is nowadays pretty limited:
1. spin_unlock_wait() has been removed from the kernel in favor
of a lock/unlock combo. Furthermore, queued spinlocks have now
for a number of years no longer relied on _Q_LOCKED_VAL for the
call, but any non-zero value to indicate a locked state. There
were cases where the delayed locked store could lead to breaking
mutual exclusion with crossed locking; such as with sysv ipc and
netfilter being the most extreme.
2. The auditing Andrea did in verified that remaining spin_is_locked()
no longer rely on such semantics. Most callers just use it to assert
a lock is taken, in a debug nature. The only user that gets cute is
NOLOCK qdisc, as of:
96009c7d500e (sched: replace __QDISC_STATE_RUNNING bit with a spin lock)
... which ironically went in the next day after c6f5d02b6a0f. This
change replaces test_bit() with spin_is_locked() to know whether
to take the busylock heuristic to reduce contention on the main
qdisc lock. So any races against spin_is_locked() for archs that
use LL/SC for spin_lock() will be benign and not break any mutual
exclusion; furthermore, both the seqlock and busylock have the same
scope.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210309015950.27688-3-dave@stgolabs.net
|
|
Instead of both queued and simple spinlocks doing it. Move
it into the arch's spinlock.h.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210309015950.27688-2-dave@stgolabs.net
|
|
Use user access block in gpr32_set_common() instead of
repetitive __get_user() which imply repetitive KUAP open/close.
To get it clean, force inlining of the small set of tiny functions
called inside the block.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/bdcb8652c3bb4ab5b8b3bfd08147434be8fc04c9.1615398498.git.christophe.leroy@csgroup.eu
|
|
Use user_access_begin() instead of the access_ok/allow_access sequence.
This brings the missing might_fault() check.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/6cd202cdc4f939d47822e4ddd3c0856210431a58.1615398498.git.christophe.leroy@csgroup.eu
|
|
Use user_access_begin() instead of the
might_sleep/access_ok/allow_access sequence.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/2dee286d2d6dc9a27d99e31ac564bad4fae2cb49.1615398498.git.christophe.leroy@csgroup.eu
|
|
__put_user_asm_goto() is internal to uaccess.h
Use __put_kernel_nofault() instead. The generated code is identical.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/3e32c4f0361933909368b68f5ee569e5de661c1b.1615398498.git.christophe.leroy@csgroup.eu
|
|
Instead of opencodying the copy of parameters, use
the generic sys_old_select().
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/4de983ad254739da1fe6e9f273baf387b7043ae0.1615398498.git.christophe.leroy@csgroup.eu
|
|
copy_mc_xxx() functions are in the middle of raw_copy functions.
For clarity, move them out of the raw_copy functions block.
They are using access_ok, so they need to be after the general
functions in order to eventually allow the inclusion of
asm-generic/uaccess.h in some future.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/2cdecb6e5a2fcee6c158d18dd254b71ec0e0da4d.1615398498.git.christophe.leroy@csgroup.eu
|
|
It is clear_user() which is expected to call __clear_user(),
not the reverse.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/d8ec01fb22f33d87321451d5e5f01cb56dacaa39.1615398498.git.christophe.leroy@csgroup.eu
|
|
ppc32 has an efficiant 64 bits __put_user(), so also use it in
order to unroll loops more.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/ccc08a16eea682d6fa4acc957ffe34003a8f0844.1615398498.git.christophe.leroy@csgroup.eu
|
|
This is helpful to read the security flavor from inside the LPAR.
In /sys/kernel/debug/powerpc/security_features it can be seen if
mitigations are on or off but not the level set through the ASMI menu.
Furthermore, reporting it through /proc/powerpc/lparcfg allows an easy
processing by the lparstat command [1].
Export it like this in /proc/powerpc/lparcfg:
$ grep security_flavor /proc/powerpc/lparcfg
security_flavor=1
Value follows what is documented on the IBM support page [2]:
0 Speculative execution fully enabled
1 Speculative execution controls to mitigate user-to-kernel attacks
2 Speculative execution controls to mitigate user-to-kernel and
user-to-user side-channel attacks
[1] https://groups.google.com/g/powerpc-utils-devel/c/NaKXvdyl_UI/m/wa2stpIDAQAJ
[2] https://www.ibm.com/support/pages/node/715841
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210305125554.5165-1-ldufour@linux.ibm.com
|
|
Print out domain name when reset fails to acquire for debugging purposes
and to make formatting of GENPD errors consistent in the driver.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Switch all clocks of a power domain to a safe rate which is suitable
for all possible voltages in order to ensure that hardware constraints
aren't violated when power domain state toggles.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The SW-initiated power gate toggling is dropped by PMC if there is
contention with a HW-initiated toggling, i.e. when one of CPU cores is
gated by cpuidle driver. Software should retry the toggling after 10
microseconds on Tegra20/30 SoCs, hence add the retrying. On Tegra114+ the
toggling method was changed in hardware, the TOGGLE_START bit indicates
whether PMC is busy or could accept the command to toggle, hence handle
that bit properly.
The problem pops up after enabling dynamic power gating of 3D hardware,
where 3D power domain fails to turn on/off "randomly".
The programming sequence and quirks are documented in TRMs, but PMC
driver obliviously re-used the Tegra20 logic for Tegra30+, which strikes
back now. The 10 microseconds and other timeouts aren't documented in TRM,
they are taken from downstream kernel.
Link: https://nv-tegra.nvidia.com/gitweb/?p=linux-2.6.git;a=commit;h=311dd1c318b70e93bcefec15456a10ff2b9eb0ff
Link: https://nv-tegra.nvidia.com/gitweb/?p=linux-3.10.git;a=commit;h=7f36693c47cb23730a6b2822e0975be65fb0c51d
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The tegra_powergate_power_up() has a typo in the error code path where it
will try to disable clocks twice, fix it. In practice that error never
happens, so this is a minor correction.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Fix voltage coupler lockup which happens when voltage-spread is out
of range due to a bug in the code. The max-spread requirement shall be
accounted when CPU regulator doesn't have consumers. This problem is
observed on Tegra30 Ouya game console once system-wide DVFS is enabled
in a device-tree.
Fixes: 783807436f36 ("soc/tegra: regulators: Add regulators coupler for Tegra30")
Cc: stable@vger.kernel.org
Reported-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This commit implements a register map which grants USB (UTMI and HSIC)
sleepwalk registers access to USB PHY drivers. The USB sleepwalk logic
is in PMC hardware block but USB PHY drivers have the best knowledge
of proper programming sequence.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
When executing the daemon test on Arm64 and x86 with Debian (Buster)
distro, both skip the test case with the log:
# ./perf test -v 76
76: daemon operations :
--- start ---
test child forked, pid 11687
test daemon list
trap: SIGINT: bad trap
./tests/shell/daemon.sh: 173: local: cpu-clock: bad variable name
test child finished with -2
---- end ----
daemon operations: Skip
So the error happens for the variable expansion when use local variable
in the shell script. Since Debian Buster uses dash but not bash as
non-interactive shell, when execute the daemon testing, it hits a known
issue for dash which was reported [1].
To resolve this issue, one option is to add double quotes for all local
variables assignment, so need to change the code from:
local line=`perf daemon --config ${config} -x: | head -2 | tail -1`
... to:
local line="`perf daemon --config ${config} -x: | head -2 | tail -1`"
But the testing script has bunch of local variables, this leads to big
changes for whole script.
On the other hand, the testing script asks to use the "local" feature
which is bash-specific, so this patch explicitly uses "#!/bin/bash" to
ensure running the script with bash.
After:
# ./perf test -v 76
76: daemon operations :
--- start ---
test child forked, pid 11329
test daemon list
test daemon reconfig
test daemon stop
test daemon signal
signal 12 sent to session 'test [11596]'
signal 12 sent to session 'test [11596]'
test daemon ping
test daemon lock
test child finished with 0
---- end ----
daemon operations: Ok
[1] https://bugs.launchpad.net/ubuntu/+source/dash/+bug/139097
Fixes: 2291bb915b55 ("perf tests: Add daemon 'list' command test")
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210320104554.529213-1-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The sort dimension "p_stage_cyc" is used to represent pipeline
stage cycle information. Presently, this is used only in powerpc.
For unsupported platforms, we don't want to display it
in the perf report output columns. Hence add check in sort_dimension__add()
and skip the sort key incase it is not applicable for the particular arch.
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Link: https://lore.kernel.org/r/1616425047-1666-6-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The pipeline stage cycles details can be recorded on powerpc from the
contents of Performance Monitor Unit (PMU) registers. On ISA v3.1
platform, sampling registers exposes the cycles spent in different
pipeline stages. Patch adds perf tools support to present two of the
cycle counter information along with memory latency (weight).
Re-use the field 'ins_lat' for storing the first pipeline stage cycle.
This is stored in 'var2_w' field of 'perf_sample_weight'.
Add a new field 'p_stage_cyc' to store the second pipeline stage cycle
which is stored in 'var3_w' field of perf_sample_weight.
Add new sort function 'Pipeline Stage Cycle' and include this in
default_mem_sort_order[]. This new sort function may be used to denote
some other pipeline stage in another architecture. So add this to list
of sort entries that can have dynamic header string.
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Link: https://lore.kernel.org/r/1616425047-1666-5-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|