| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Instead of using kmalloc + memcpy, use kmemdup
to simplify the code.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This conexant codec isn't in the supported codec list yet, the hda
generic driver can drive this codec well, but on a Lenovo machine
with mute/mic-mute leds, we need to apply CXT_FIXUP_THINKPAD_ACPI
to make the leds work. After adding this codec to the list, the
driver patch_conexant.c will apply THINKPAD_ACPI to this machine.
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It turned out that the recent Intel HD-audio controller chips show a
significant stall during the system PM resume intermittently. It
doesn't happen so often and usually it may read back successfully
after one or more seconds, but in some rare worst cases the driver
went into fallback mode.
After trial-and-error, we found out that the communication stall seems
covered by issuing the sync after each verb write, as already done for
AMD and other chipsets. So this patch enables the write-sync flag for
the recent Intel chips, Skylake and onward, as a workaround.
Also, since Broxton and co have the very same driver flags as Skylake,
refer to the Skylake driver flags instead of defining the same
contents again for simplification.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201901
Reported-and-tested-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
If the DAI format setup fails, there is no valid communication format
between CPU and CODEC, so fail card instantiation, rather than continue
with a card that will most likely not function properly.
Signed-off-by: Ricard Wanderlof <ricardw@axis.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.20.1907241132350.6338@lnxricardw1.se.axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
sizeof (byte) is always 1, use that fact and make interesting code explicit.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
put_device will call ac97_codec_release to free
ac97_codec_device and other resources, so remove the kfree
and other redundant code.
Fixes: 74426fbff66e ("ALSA: ac97: add an ac97 bus")
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Downgrade "nothing to do in IRQ thread" message from error to a debug
message in the IPC interrupt handler thread.
The spurious wake-up can happen if a HDA stream interrupt is
raised while the IPC interrupt thread is running. IPC functionality
is not impacted by this condition, so debug is a more appropriate
trace level.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-21-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
apq8016_sbc_parse_of() sets up multiple DAI links, depending on the
number of nodes in the device tree. However, at the moment
CPU and platform components are only allocated for the first link.
This causes an oops when more than one link is defined:
Internal error: Oops: 96000044 [#1] SMP
CPU: 0 PID: 1015 Comm: kworker/0:2 Not tainted 5.3.0-rc1 #4
Call trace:
apq8016_sbc_platform_probe+0x1a8/0x3f0
platform_drv_probe+0x50/0xa0
...
Move the allocation inside the loop to ensure that each link is
properly initialized.
Fixes: 98b232ca9e0e ("ASoC: qcom: apq8016_sbc: use modern dai_link style")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20190722130352.95874-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Draining makes little sense in the situation of hardware overrun, as the
hardware will have consumed all its available samples. Additionally,
draining whilst the stream is paused would presumably get stuck as no
data is being consumed on the DSP side.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Partial drain and next track are intended for gapless playback and
don't really have an obvious interpretation for a capture stream, so
makes sense to not allow those operations on capture streams.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Currently, whilst in SNDRV_PCM_STATE_OPEN it is possible to call
snd_compr_stop, snd_compr_drain and snd_compr_partial_drain, which
allow a transition to SNDRV_PCM_STATE_SETUP. The stream should
only be able to move to the setup state once it has received a
SNDRV_COMPRESS_SET_PARAMS ioctl. Fix this issue by not allowing
those ioctls whilst in the open state.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A previous fix to the stop handling on compressed capture streams causes
some knock on issues. The previous fix updated snd_compr_drain_notify to
set the state back to PREPARED for capture streams. This causes some
issues however as the handling for snd_compr_poll differs between the
two states and some user-space applications were relying on the poll
failing after the stream had been stopped.
To correct this regression whilst still fixing the original problem the
patch was addressing, update the capture handling to skip the PREPARED
state rather than skipping the SETUP state as it has done until now.
Fixes: 4f2ab5e1d13d ("ALSA: compress: Fix stop handling on compressed capture streams")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In snd_soc_dapm_new_control_unlocked(), a kernel buffer is allocated in
dapm_cnew_widget() to hold the new dapm widget. Then, different actions are
taken according to the id of the widget, i.e., 'w->id'. If any failure
occurs during this process, snd_soc_dapm_new_control_unlocked() should be
terminated by going to the 'request_failed' label. However, the allocated
kernel buffer is not freed on this code path, leading to a memory leak bug.
To fix the above issue, free the buffer before returning from
snd_soc_dapm_new_control_unlocked() through the 'request_failed' label.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Link: https://lore.kernel.org/r/1563803864-2809-1-git-send-email-wang6495@umn.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
MOTU data block processing layer has some tracepoints events. This
commit is code refactoring to split probing the events from processing
data blocks.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
descriptors
This commit changes each of data block processing layer so that it
receives list of packet descriptor.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is code refactoring for FF data block processing layer so that
it can receive list of packet descriptor.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is code refactoring for MOTU data block processing layer so that
it can receive list of packet descriptor.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is code refactoring for TASCAM data block processing layer so that
it can receive list of packet descriptor.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is code refactoring for DOT data block processing layer so that
it can receive list of packet descriptor.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is code refactoring for AM824 data block processing layer so that
it can receive list of packet descriptor.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit changes signature of callback function to call data block
processing layer with packet descriptor. At present, the layer is called
per packet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is code refactoring for common processing for payloads of
ishocornous context.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is code refactoring to separate PCM substream processing from packet
queueing.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit uses packet descriptor to parse headers of IR context and
parse timing information for sequence transferred by target device.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit uses packet descriptor to parse headers of IT context and
generate timing information for ideal sequence.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In current implementation of ALSA IEC 61883-1/6 packet streaming engine,
16 packets are handled in one interrupt of isochronous context of OHCI
1394.
Overall packet processing runs for each. However, this is not better in
a point to split the processing into several parts.
This commit is an attempt to add intermediate representation for
parameters required for the parts.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In a previous commit, the variable passed from packet streaming layer
for syt variable is useless. This commit obsoletes it.
In my future work, the syt information is passed to data block processing
layer by another way.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Some protocols don't use syt field of CIP header to represent
presentation timestamp. For such protocol, ALSA IEC 61883-1/6
packet streaming engine uses a pointer into local variable for
the value of syt to call data block processing layer. However,
it can decide the value when initializing packet streaming
layer.
This commit adds 'syt_override' member for packet streaming
layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
for IR context
In ALSA IEC 61883-1/6 packet streaming engine, two types of data block
counter are supported. This commit applies code refactoring to make it
explicitly for IR context.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
for IT context
In ALSA IEC 61883-1/6 packet streaming engine, two types of data block
counter are supported. This commit applies code refactoring to make it
explicitly for IT context.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is a preparation for future commit that 'struct
amdtp_stream.data_block_count' does not represent the value of
data block count for current data block.
However, data block count is required for calculation of sequence index
in sequence-multiplied data channel. Some of data block processing layer
require it; e.g. for AM824 data block.
This commit passes data block count to the processing layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is a preparation for future commit that 'struct
amdtp_stream.data_block_count' does not represent the value of
data block count for current data block.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Recent firmware for Fireworks board module have a quirk to start
transmission of CIP with non-zero value for its data block counter.
In current implementation of ALSA firewire stack, the quirk is handled
by 'struct amdtp_stream.ctx_data.tx.first_dbc' with value 0x02. However,
the value comes from reverse engineering. It's better to handle this
quirk without the explicit value.
In a process to parse CIP header, the quirk of data block counter
affects decision of sequence index in sequence-multiplexed data channel;
i.e. MIDI conformant data channel. In Fireworks, the index is decided
by the number of data blocks from top of the same CIP, thus the value
of data block counter is useless.
This commit adds CIP_UNALIGHED_DBC flag and obsoletes the explicit
value for this quirk.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When CONFIG_UAPI_HEADER_TEST=y, exported headers are compile-tested to
make sure they can be included from user-space.
Currently, header.h and fw.h are excluded from the test coverage.
To make them join the compile-test, we need to fix the build errors
attached below.
For a case like this, we decided to use __u{8,16,32,64} variable types
in this discussion:
https://lkml.org/lkml/2019/6/5/18
Build log:
CC usr/include/sound/sof/header.h.s
CC usr/include/sound/sof/fw.h.s
In file included from <command-line>:32:0:
./usr/include/sound/sof/header.h:19:2: error: unknown type name ‘uint32_t’
uint32_t magic; /**< 'S', 'O', 'F', '\0' */
^~~~~~~~
./usr/include/sound/sof/header.h:20:2: error: unknown type name ‘uint32_t’
uint32_t type; /**< component specific type */
^~~~~~~~
./usr/include/sound/sof/header.h:21:2: error: unknown type name ‘uint32_t’
uint32_t size; /**< size in bytes of data excl. this struct */
^~~~~~~~
./usr/include/sound/sof/header.h:22:2: error: unknown type name ‘uint32_t’
uint32_t abi; /**< SOF ABI version */
^~~~~~~~
./usr/include/sound/sof/header.h:23:2: error: unknown type name ‘uint32_t’
uint32_t reserved[4]; /**< reserved for future use */
^~~~~~~~
./usr/include/sound/sof/header.h:24:2: error: unknown type name ‘uint32_t’
uint32_t data[0]; /**< Component data - opaque to core */
^~~~~~~~
In file included from <command-line>:32:0:
./usr/include/sound/sof/fw.h:49:2: error: unknown type name ‘uint32_t’
uint32_t size; /* bytes minus this header */
^~~~~~~~
./usr/include/sound/sof/fw.h:50:2: error: unknown type name ‘uint32_t’
uint32_t offset; /* offset from base */
^~~~~~~~
./usr/include/sound/sof/fw.h:64:2: error: unknown type name ‘uint32_t’
uint32_t size; /* bytes minus this header */
^~~~~~~~
./usr/include/sound/sof/fw.h:65:2: error: unknown type name ‘uint32_t’
uint32_t num_blocks; /* number of blocks */
^~~~~~~~
./usr/include/sound/sof/fw.h:73:2: error: unknown type name ‘uint32_t’
uint32_t file_size; /* size of file minus this header */
^~~~~~~~
./usr/include/sound/sof/fw.h:74:2: error: unknown type name ‘uint32_t’
uint32_t num_modules; /* number of modules */
^~~~~~~~
./usr/include/sound/sof/fw.h:75:2: error: unknown type name ‘uint32_t’
uint32_t abi; /* version of header format */
^~~~~~~~
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20190721142308.30306-1-yamada.masahiro@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The TS3A227E says that the headset keypress detection needs the MICBIAS
power in order to report the key events to ensure proper operation
The headset keypress detection needs the MICBIAS power in order to report
the key events all the time as long as MIC is present. So MICBIAS pin
is forced on when a MICROPHONE is detected.
On Veyron Minnie I observed that if the MICBIAS power is not present and
the key press detection is activated (just because it is enabled when you
insert a headset), it randomly reports a keypress on insert.
E.g. (KEY_PLAYPAUSE)
Event: (SW_HEADPHONE_INSERT), value 1
Event: (SW_MICROPHONE_INSERT), value 1
Event: -------------- SYN_REPORT ------------
Event: (KEY_PLAYPAUSE), value 1
Userspace thinks that KEY_PLAYPAUSE is pressed and produces the annoying
effect that the media player starts a play/pause loop.
Note that, although most of the time the key reported is the one
associated with BTN_0, not always this is true. On my tests I also saw
different keys reported
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20190719173929.24065-1-enric.balletbo@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When sample rate of TX is different with sample rate of RX in
async mode, the MFreq selection will be wrong.
For example, sysclk = 24.576MHz, TX rate = 96000Hz, RX rate = 48000Hz.
Then ratio of TX = 256, ratio of RX = 512, For MFreq is shared by TX
and RX instance, the correct value of MFreq is 2 for both TX and RX.
But original method will cause MFreq = 0 for TX, MFreq = 2 for RX.
If TX is started after RX, RX will be impacted, RX work abnormal with
MFreq = 0.
This patch is to select proper MFreq value according to TX rate and
RX rate.
Fixes: 0c516b4ff85c ("ASoC: cs42xx8: Add codec driver support for CS42448/CS42888")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/20190716094547.46787-1-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
DPCM uses snd_soc_dapm_dai_get_connected_widgets to build a
list of the widgets connected to a specific front end DAI so it
can search through this list for available back end DAIs. The
custom_stop_condition was added to is_connected_ep to facilitate this
list not containing more widgets than is necessary. Doing so both
speeds up the DPCM handling as less widgets need to be searched and
avoids issues with CODEC to CODEC links as these would be confused
with back end DAIs if they appeared in the list of available widgets.
custom_stop_condition was implemented by aborting the graph walk
when the condition is triggered, however there is an issue with this
approach. Whilst walking the graph is_connected_ep should update the
endpoints cache on each widget, if the walk is aborted the number
of attached end points is unknown for that sub-graph. When the stop
condition triggered, the original patch ignored the triggering widget
and returned zero connected end points; a later patch updated this
to set the triggering widget's cache to 1 and return that. Both of
these approaches result in inaccurate values being stored in various
end point caches as the values propagate back through the graph,
which can result in later issues with widgets powering/not powering
unexpectedly.
As the original goal was to reduce the size of the widget list passed
to the DPCM code, the simplest solution is to limit the functionality
of the custom_stop_condition to the widget list. This means the rest
of the graph will still be processed resulting in correct end point
caches, but only widgets up to the stop condition will be added to the
returned widget list.
Fixes: 6742064aef7f ("ASoC: dapm: support user-defined stop condition in dai_get_connected_widgets")
Fixes: 5fdd022c2026 ("ASoC: dpcm: play nice with CODEC<->CODEC links")
Fixes: 09464974eaa8 ("ASoC: dapm: Fix to return correct path list in is_connected_ep.")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20190718084333.15598-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Pull the support for AMD / Nvidia HD-audio compmonent notification
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
I was looking at
<4> [241.835158] general protection fault: 0000 [#1] PREEMPT SMP PTI
<4> [241.835181] CPU: 1 PID: 214 Comm: kworker/1:3 Tainted: G U 5.2.0-CI-CI_DRM_6509+ #1
<4> [241.835199] Hardware name: Dell Inc. OptiPlex 745 /0GW726, BIOS 2.3.1 05/21/2007
<4> [241.835234] Workqueue: events snd_hdac_bus_process_unsol_events [snd_hda_core]
<4> [241.835256] RIP: 0010:input_handle_event+0x16d/0x5e0
<4> [241.835270] Code: 48 8b 93 58 01 00 00 8b 52 08 89 50 04 8b 83 f8 06 00 00 48 8b 93 00 07 00 00 8d 70 01 48 8d 04 c2 83 e1 08 89 b3 f8 06 00 00 <66> 89 28 66 44 89 60 02 44 89 68 04 8b 93 f8 06 00 00 0f 84 fd fe
<4> [241.835304] RSP: 0018:ffffc9000019fda0 EFLAGS: 00010046
<4> [241.835317] RAX: 6b6b6b6ec6c6c6c3 RBX: ffff8880290fefc8 RCX: 0000000000000000
<4> [241.835332] RDX: 000000006b6b6b6b RSI: 000000006b6b6b6c RDI: 0000000000000046
<4> [241.835347] RBP: 0000000000000005 R08: 0000000000000000 R09: 0000000000000001
<4> [241.835362] R10: ffffc9000019faa0 R11: 0000000000000000 R12: 0000000000000004
<4> [241.835377] R13: 0000000000000000 R14: ffff8880290ff1d0 R15: 0000000000000293
<4> [241.835392] FS: 0000000000000000(0000) GS:ffff88803de80000(0000) knlGS:0000000000000000
<4> [241.835409] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4> [241.835422] CR2: 00007ffe9a99e9b7 CR3: 000000002f588000 CR4: 00000000000006e0
<4> [241.835436] Call Trace:
<4> [241.835449] input_event+0x45/0x70
<4> [241.835464] snd_jack_report+0xdc/0x100
<4> [241.835490] snd_hda_jack_report_sync+0x83/0xc0 [snd_hda_codec]
<4> [241.835512] snd_hdac_bus_process_unsol_events+0x5a/0x70 [snd_hda_core]
<4> [241.835530] process_one_work+0x245/0x610
which has the hallmarks of a worker queued from interrupt after it was
supposedly cancelled (note the POISON_FREE), and I could not see where
the interrupt would be flushed on shutdown so added the likely suspects.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111174
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
AMD/ATI and Nvidia HDMI codec drivers didn't have the audio component
binding like i915, but it worked only with the traditional HD-audio
unsolicited event for the HDMI hotplug detection and the ELD read-up
thereafter. This has been a problem in many ways: first of all, it
goes through the hardware event transition (from GPU register write,
HD-audio controller trigger, and finally to HD-audio unsolicited event
handling), which is often unreliable and may miss some opportunities.
Second, each unsol event handling and ELD read-up need the explicit
power up / down when the codec is in the runtime suspend. Last but
not least, which is the most important, the hotplug wakeup may be
missed when the HD-audio controller is in runtime suspend. Especially
the last point is a big problem due to the recent change relevant with
vga_switcheroo that forcibly enables the runtime PM for AMD HDMI
controllers.
These issues are solved by introducing the audio component; the
hotplug notification is done by a direct function callback, which is
more accurate and reliable, and it can be processed without the actual
hardware access, i.e. no runtime PM trigger is needed, and the
HD-audio gets the event even if it's in runtime suspend. The same for
ELD query, as it's read directly from the cached ELD bytes stored in
the DRM driver, hence the whole hardware access can be skipped.
So here it is: this patch implements the audio component binding with
AMD/ATI and Nouveau DRM drivers. The biggest difference from i915
implementation is that this binding is fully optional and it can be
enabled asynchronously on the fly. That is, the driver will switch
from the HD-audio unsolicited event to the notify callback once when
the DRM component gets bound. Similarly, when DRM driver gets
unloaded, the HDMI event handling returns to the legacy mode, too.
Also, another difference from i915 is that the new code registers the
component in the codec driver, while i915 HDMI codec assumes the
component binding was already done in the HD-audio controller driver.
Hence the new code does need to de-register the component binding at
the codec exit, too.
Some other details:
- The match component ops assumes that both VGA and HD-audio
controller PCI entries belong to the same PCI bus, and only accepts
such an entry.
- The pin2port audio_ops is implemented with assumption of the fixed
widget layout. For AMD, it's starting from 3, with step 2 (3, 5, 7,
...), while for Nvidia, it's starting from 4, with step 1 (4, 5, 6,
...)
As of this patch, the corresponding component isn't implemented in DRM
side, so this change alone won't give any benefit. By the following
changes in DRM sides, the mission will be completed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The HDMI jack handling reports the state change always via
snd_jack_report() whenever hdmi_present_sense() is called, even if the
state itself doesn't change from the previous time. This is mostly
harmless but still a bit confusing to user-space.
This patch reduces such spurious jack state changes and reports only
when the state really changed. Also, as a minor optimization, avoid
overwriting the pin ELD data when the state is identical.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
s/Vairax/Variax/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
"Fix several warnings/errors in validation of binding schemas"
* tag 'devicetree-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: pinctrl: stm32: Fix missing 'clocks' property in examples
dt-bindings: iio: ad7124: Fix dtc warnings in example
dt-bindings: iio: avia-hx711: Fix avdd-supply typo in example
dt-bindings: pinctrl: aspeed: Fix AST2500 example errors
dt-bindings: pinctrl: aspeed: Fix 'compatible' schema errors
dt-bindings: riscv: Limit cpus schema to only check RiscV 'cpu' nodes
dt-bindings: Ensure child nodes are of type 'object'
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs documentation typo fix from Al Viro.
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
typo fix: it's d_make_root, not d_make_inode...
|
|
Pull cifs fixes from Steve French:
"Two fixes for stable, one that had dependency on earlier patch in this
merge window and can now go in, and a perf improvement in SMB3 open"
* tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module number
cifs: flush before set-info if we have writeable handles
smb3: optimize open to not send query file internal info
cifs: copy_file_range needs to strip setuid bits and update timestamps
CIFS: fix deadlock in cached root handling
|
|
The commit b3aa14f02254 ("iommu: remove the mapping_error dma_map_ops
method") incorrectly changed the checking from dma_ops_alloc_iova() in
map_sg() causes a crash under memory pressure as dma_ops_alloc_iova()
never return DMA_MAPPING_ERROR on failure but 0, so the error handling
is all wrong.
kernel BUG at drivers/iommu/iova.c:801!
Workqueue: kblockd blk_mq_run_work_fn
RIP: 0010:iova_magazine_free_pfns+0x7d/0xc0
Call Trace:
free_cpu_cached_iovas+0xbd/0x150
alloc_iova_fast+0x8c/0xba
dma_ops_alloc_iova.isra.6+0x65/0xa0
map_sg+0x8c/0x2a0
scsi_dma_map+0xc6/0x160
pqi_aio_submit_io+0x1f6/0x440 [smartpqi]
pqi_scsi_queue_command+0x90c/0xdd0 [smartpqi]
scsi_queue_rq+0x79c/0x1200
blk_mq_dispatch_rq_list+0x4dc/0xb70
blk_mq_sched_dispatch_requests+0x249/0x310
__blk_mq_run_hw_queue+0x128/0x200
blk_mq_run_work_fn+0x27/0x30
process_one_work+0x522/0xa10
worker_thread+0x63/0x5b0
kthread+0x1d2/0x1f0
ret_from_fork+0x22/0x40
Fixes: b3aa14f02254 ("iommu: remove the mapping_error dma_map_ops method")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The hexagon implementation pte_alloc_one(), pte_alloc_one_kernel(),
pte_free_kernel() and pte_free() is identical to the generic except of
lack of __GFP_ACCOUNT for the user PTEs allocation.
Switch hexagon to use generic version of these functions.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull NTB updates from Jon Mason:
"New feature to add support for NTB virtual MSI interrupts, the ability
to test and use this feature in the NTB transport layer.
Also, bug fixes for the AMD and Switchtec drivers, as well as some
general patches"
* tag 'ntb-5.3' of git://github.com/jonmason/ntb: (22 commits)
NTB: Describe the ntb_msi_test client in the documentation.
NTB: Add MSI interrupt support to ntb_transport
NTB: Add ntb_msi_test support to ntb_test
NTB: Introduce NTB MSI Test Client
NTB: Introduce MSI library
NTB: Rename ntb.c to support multiple source files in the module
NTB: Introduce functions to calculate multi-port resource index
NTB: Introduce helper functions to calculate logical port number
PCI/switchtec: Add module parameter to request more interrupts
PCI/MSI: Support allocating virtual MSI interrupts
ntb_hw_switchtec: Fix setup MW with failure bug
ntb_hw_switchtec: Skip unnecessary re-setup of shared memory window for crosslink case
ntb_hw_switchtec: Remove redundant steps of switchtec_ntb_reinit_peer() function
NTB: correct ntb_dev_ops and ntb_dev comment typos
NTB: amd: Silence shift wrapping warning in amd_ntb_db_vector_mask()
ntb_hw_switchtec: potential shift wrapping bug in switchtec_ntb_init_sndev()
NTB: ntb_transport: Ensure qp->tx_mw_dma_addr is initaliazed
NTB: ntb_hw_amd: set peer limit register
NTB: ntb_perf: Clear stale values in doorbell and command SPAD register
NTB: ntb_perf: Disable NTB link after clearing peer XLAT registers
...
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
