| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Drop "Common NI Values Table" and calculate LRCLK divider, then
add allowed rate constraints based on master clock frequency.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Implement set_bias_level to drive shutdown bit, so device is
put to sleep when unused.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ret is assigned later, no need to initialize it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Get the reset GPIO through the GPIO consumer API. This allows specifying the
DT property as "reset-gpios" without breaking existing DT users.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Bindings should use 'reset-gpios', not 'reset-gpio'. The driver needs to
switch to the gpiod consume API to handle this correctly.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Get the reset GPIO through the GPIO consumer API. This allows specifying the
DT property as "reset-gpios" without breaking existing DT users.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Bindings should use 'reset-gpios', not 'reset-gpio'. The driver needs to
switch to the gpiod consume API to handle this correctly.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
For the FSL ASoC card, the full node names appear to be "ssi", "esai",
and "sai", so there's not any reason to use strstr and of_node_name_eq
can be used instead.
Cc: Timur Tabi <timur@kernel.org>
Cc: Nicolin Chen <nicoleotsuka@gmail.com>
Cc: Xiubo Li <Xiubo.Lee@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
AMD platform device acp_audio_dma can only be created by parent PCI
device driver (drivers/gpu/drm/amd/amdgpu/amdgpu_acp.c). Pass struct
device of the parent to snd_pcm_lib_preallocate_pages() so
dma_alloc_coherent() can use correct dma_ops. Otherwise, it will
use default dma_ops which is nommu_dma_ops on x86_64 even when
IOMMU is enabled and set to non passthrough mode.
Though platform device inherits some dma related fields during its
creation in mfd_add_device(), we can't simply pass its struct device
to snd_pcm_lib_preallocate_pages() because dma_ops is not among the
inherited fields. Even it were, drivers/iommu/amd_iommu.c would
ignore it because get_device_id() doesn't handle platform device.
This change shouldn't give us any trouble even struct device of the
parent becomes null or represents some non PCI device in the future,
because get_dma_ops() correctly handles null struct device or uses
the default dma_ops if struct device doesn't have it set.
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We shouldn't assume CPU physical address we get from page_to_phys()
is same as DMA address we get from dma_alloc_coherent(). On x86_64,
we won't run into any problem with the assumption when dma_ops is
nommu_dma_ops. However, DMA address is IOVA when IOMMU is enabled.
And it's most likely different from CPU physical address when AMD
IOMMU is not in passthrough mode.
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch added max98373_reset function to avoid amp software reset failure and code duplication.
Reset verification step has been added for stable amp reset and it repeats verification maximum 3 times when it is failed.
Chip revision ID is available when the amp is in the idle state which means software reset is completed well.
Additional 10ms delay was added for every retrial and maximum 30ms delay can be applied.
Signed-off-by: Ryan Lee <ryans.lee@maximintegrated.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In DPCM case, it uses CPU-dummy / dummy-Codec dai links, and
non DPCM case, it uses CPU-Codec dai links.
Now, we want to merge audio-graph-card and audio-graph-scu-card.
These sound cards are using silimar but not same logic on each functions.
Then, of course we want to share same logic.
To compromise, this patch uses cpu/codec pointer on audio-graph-card.
It is same logic with audio-graph-scu-card, thus easy merging.
This is prepare for merging audio card
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current audio-graph-scu-card didn't care about codec_conf
for multi DPCM case. This patch cares it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In DPCM case, it uses CPU-dummy / dummy-Codec dai links, and
non DPCM case, it uses CPU-Codec dai links.
Now, we want to merge audio-graph-card and audio-graph-scu-card.
These sound cards are using silimar but not same logic on each functions.
Then, of course we want to share same logic.
To compromise, this patch uses cpu/codec pointer on audio-graph-scu-card.
It is same logic with audio-graph-card, thus easy merging.
This is prepare for merging audio card
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In DPCM case, it uses CPU-dummy / dummy-Codec dai links.
If sound card is caring only DPCM, link count = dai count,
but, if non DPCM case, link count != dai count.
Now, we want to merge audio-graph-card and audio-graph-scu-card,
then, we need to care both link / dai count more carefly
This patch cares it, and prepare for merging audio card
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
asoc_simple_card_get_dai_id() returns DAI ID, but it is based on
DT node's "endpoint" position.
Almost all cases 1 port has 1 endpoint, thus, it was no problem.
But in reality, port : endpoint = 1 : N, thus, counting endpoint
is BUG, it should based on "port" ID.
This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
commit f69f452243e4e1 ("ASoC: rsnd: add TDM Split mode support")
added TDM Split mode support for rsnd driver.
But, it cares audio-graph-card style only. We can't use TDM Split
mode on simple-card style now.
This patch fixup this issue.
Fixes: f69f452243e4e1 ("ASoC: rsnd: add TDM Split mode support")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
commit c16015f36cc12824 ("ASoC: rsnd: add .get_id/.get_id_sub")
add new .get_id/.get_id_sub to indicate module ID/subID.
It is used for SSIU and CTU. In SSIU case, subID indicates BUSIF,
but register settings is based on SSIU ID.
OTOH, in CTU case, subID indicates CTU channel, and register settings
is based on it. This means regmap read/write function needs to care it.
This patch fixup this issue. It can't play MIXed sound without this
patch.
Fixes: c16015f36cc12824 ("ASoC: rsnd: add .get_id/.get_id_sub")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For TDM debug purpose, indicating Channel and Mode is very
useful. This patch indicate it if it has #define DEBUG
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
These boards are now fully ported to devicetree and make use of the
simple-card driver, so the platform specific machine driver can be
removed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Entry needed for ICL RVP w/ RT274
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The example should follow the practice or using a generic node name
instead of the precise programming model, as recommended by the DTSpec.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add suffix ULL to constant 256 in order to give the compiler complete
information about the proper arithmetic to use.
Notice that such constant is used in a context that expects an
expression of type u64 (64 bits, unsigned) and the following
expression is currently being evaluated using 32-bit arithmetic:
256 * fs * 2 * mclk_src_scaling[i].param
Signed-off-by: Young_X <YangX92@hotmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Introducing a module param for wakeup_delay in order to
align with modeswitch_delay parameter. With this change, both
wakeup_delay and modeswitch_delay parameters can be passed
as module parameters.
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On startup, applications such as PulseAudio or CRAS enable playback or
capture on all PCM devices to verify that configurations are correct,
and close them immediately. For DMICs, this can result in the clock
being turned off very quickly, which may not compatible with internal
state machine transition requirements.
This patch add a mode-switch delay which will prevent the clock from
being turned off without complying with manufacturer timing
specifications. While the DMIC clock may be controlled at a lower level,
be it with hardware or firmware, applying the delay during the
STOP_TRIGGER phase ensures that there is no race condition, e.g. with
the hardware/firmware turning off the clock earlier
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Jairaj Arava <jairaj.arava@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
McPDM module receives it's functional clock from external source. This
clock is the pdmclk provided by the twl6040 audio IC. If the clock is not
available all register accesses to McPDM fails and the module is not
operational.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a callback for init ops on dai_link to create and setup jack.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add board specific dapm widgets so these widgets can be used
in the route.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the dismod is specified in the DT node, use the specified custom value
to configure the drive on state of the inactive TX slots.
If the dismod is not present or booted in legacy mode, the dismod is set
to low as it was the original behavior.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The dismod property can be used to specify the drive on level of inactive
TX slots.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When McASP is master and the PDIR for the clock pins are configured as
outputs before the clocking is configured it will output whatever clock
is generated at the moment internally.
The clock will switch to the correct rate only when the we start the clock
generators.
To avoid this we must only set the pin as output after the clock is
configured and enabled.
AXR pins configured as outputs behaves somehow interesting as well:
when McASP is not enabled and the pin is selected as output it will not
honor the DISMOD settings for the inactive state, but will pull the pin
down.
Add a new bitfield and mark the pins there which needs to be output and
set the pins only at the time when they will behave correctly.
On stream stop configure the pins back to input which makes them to obey
the global pin configuration regarding to pull up/down.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Follow the guideline from the TRM:
Before starting, clear the respective transmitter and receiver status
registers
To avoid stale state stored in the status registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If mclk/sclk is already running, FW responds with IPC reply MCLK/SCLK
already running. Add these to the IPC reply lookup table.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add more meaning to the IPC replies for easy debugging. Replace the switch
case with a lookup table to lookup for the IPC replies and print in human
readable form.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Minor changes to match coding style.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
commit 3b7103562c03c ("ASoC: soc-core: add
snd_soc_of_parse_node_prefix()") maked snd_soc_of_parse_audio_prefix()
as #define. But it'd be better to make this a static inline rather than
a #define. It helps with error messages and type safety.
This patch makes it inline.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
commit da48a6eb82ea2 ("ASoC: rsnd: add SSIU BUSIF support for
Document") updated Documentation for SSIU, but 1) we want to
keep old/deprecated DMA description, 2) it is missing SSIU
subnode properties. This patch tidyup these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The platform_device_register_full() function doesn't return NULL, it
returns error pointers.
Fixes: 7894a7e7ea3d ("ASoC: amd: create ACP3x PCM platform device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
commit f986907c9225 ("ASoC: audio-graph-card: add widgets and routing for
external amplifier support") added new function
asoc_graph_card_outdrv_event(), but the inserted position breaks
define area. This patch tidyup it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
1 "simple" is enough on Kconfig help
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current audio-graph-scu-card driver is parsing codec position for DPCM
and consider DAI format. But, current operation is doing totally pointless,
because 1) asoc_simple_card_parse_daifmt() will be called not only for 1st
codec on current implementation, and it will be used as fixed format
2) it should be called for each CPU/Codec pair.
Let's tidyup asoc_simple_card_parse_daifmt() timing.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
audio-graph-scu-card.c is supporting "convert-rate/channels" which is
used for DPCM.
But, sound card might have multi codecs, and each codec might need
each convert-rate/channels.
This patch supports each codec's convert-rate/channles support.
top node convert-rate/channels will overwrite settings if exist.
It can't support each codec's convert-rate/channels if sound card had
multi codecs without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
audio-graph-scu-card.c is supporting "convert-rate/channels" which is
used for DPCM.
But, sound card might have multi codecs, and each codec might need
each convert-rate/channels.
This patch supports each codec's convert-rate/channles support.
top node convert-rate/channels will overwrite settings if exist.
It can't support each codec's convert-rate/channels if sound card had
multi codecs without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
audio-graph-scu-card.c is supporting "prefix" which is used to avoid
DAI naming conflict when CPU/Codec matching.
But, sound card might have multi sub-devices, and each codec might need
each prefix.
Now, ASoC is supporting snd_soc_of_parse_node_prefix(), let's support
it on audio-graph-scu-card, too. It is keeping existing DT style.
It can't support each codec's prefix if sound card had multi sub-devices
without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
audio-graph-scu-card.c is supporting "prefix" which is used to avoid
DAI naming conflict when CPU/Codec matching.
But, sound card might have multi sub-devices, and each codec might need
each prefix.
Now, ASoC is supporting snd_soc_of_parse_node_prefix(), let's support
it on audio-graph-scu-card, too. It is keeping existing DT style.
It can't support each codec's prefix if sound card had multi sub-devices
without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
simple-scu-card.c is supporting "prefix" which is used to avoid
DAI naming conflict when CPU/Codec matching.
But, sound card might have multi sub-devices, and each codec might need
each prefix.
Now, ASoC is supporting snd_soc_of_parse_node_prefix(), let's support
it on audio-graph-scu-card, too. It is keeping existing DT style.
It can't support each codec's prefix if sound card had multi sub-devices
without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
simple-scu-card.c is supporting "prefix" which is used to avoid
DAI naming conflict when CPU/Codec matching.
But, sound card might have multi sub-devices, and each codec might need
each prefix.
Now, ASoC is supporting snd_soc_of_parse_node_prefix(), let's support
it on audio-graph-scu-card, too. It is keeping existing DT style.
It can't support each codec's prefix if sound card had multi sub-devices
without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC has snd_soc_of_parse_audio_prefix() to get codec_conf
settings from DT which is used to avoid DAI naming conflict when
CPU/Codec matching.
Currently, it is parsing from "top node",
but, we want to parse from "each sub node" if sound card had multi
cpus/codecs.
This patch adds new snd_soc_of_parse_node_prefix() to allow parsing
settings from selected node.
It is keeping existing snd_soc_of_parse_audio_prefix() by using macro.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Amplifier may have assosicated regulator, so add a widget for it
and appropriate route.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Amplifier may have associated regulator, so add a property for it.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
