| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Christoph Paasch sent a patch to address the following issue :
tcp_make_synack() is leaving some TCP private info in skb->cb[],
then send the packet by other means than tcp_transmit_skb()
tcp_transmit_skb() makes sure to clear skb->cb[] to not confuse
IPv4/IPV6 stacks, but we have no such cleanup for SYNACK.
tcp_make_synack() should not use tcp_init_nondata_skb() :
tcp_init_nondata_skb() really should be limited to skbs put in write/rtx
queues (the ones that are only sent via tcp_transmit_skb())
This patch fixes the issue and should even save few cpu cycles ;)
Fixes: 971f10eca186 ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported yet another regression added with DOIT_UNLOCKED.
When nexthop is marked as dead, fib_dump_info uses __in_dev_get_rtnl():
./include/linux/inetdevice.h:230 suspicious rcu_dereference_protected() usage!
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by syz-executor2/23859:
#0: (rcu_read_lock){....}, at: [<ffffffff840283f0>]
inet_rtm_getroute+0xaa0/0x2d70 net/ipv4/route.c:2738
[..]
lockdep_rcu_suspicious+0x123/0x170 kernel/locking/lockdep.c:4665
__in_dev_get_rtnl include/linux/inetdevice.h:230 [inline]
fib_dump_info+0x1136/0x13d0 net/ipv4/fib_semantics.c:1377
inet_rtm_getroute+0xf97/0x2d70 net/ipv4/route.c:2785
..
This isn't safe anymore, callers either hold RTNL mutex or rcu read lock,
so these spots must use rcu_dereference_rtnl() or plain rcu_derefence()
(plus unconditional rcu read lock).
This does the latter.
Fixes: 394f51abb3d04f ("ipv4: route: set ipv4 RTM_GETROUTE to not use rtnl")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Numbers in DT are stored in “cells” which are 32-bits
in size. of_property_read_u8 does not work properly
because of endianness problem.
This causes it to always return 0 with little-endian
architectures.
Fix it by using of_property_read_u32() OF API.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cong Wang says:
====================
net_sched: fix a use-after-free for tc actions
This patchset fixes a use-after-free reported by Lucas
and closes potential races too.
Please see each patch for details.
====================
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TC actions have been destroyed asynchronously for a long time,
previously in a RCU callback and now in a workqueue. If we
don't hold a refcnt for its netns, we could use the per netns
data structure, struct tcf_idrinfo, after it has been freed by
netns workqueue.
Hold refcnt to ensure netns destroy happens after all actions
are gone.
Fixes: ddf97ccdd7cb ("net_sched: add network namespace support for tc actions")
Reported-by: Lucas Bates <lucasb@mojatatu.com>
Tested-by: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I forgot to acquire RTNL in tc_action_net_exit()
which leads that action ops->cleanup() is not always
called with RTNL. This usually is not a big deal because
this function is called after all netns refcnt are gone,
but given RTNL protects more than just actions, add it
for safety and consistency.
Also add an assertion to catch other potential bugs.
Fixes: ddf97ccdd7cb ("net_sched: add network namespace support for tc actions")
Reported-by: Lucas Bates <lucasb@mojatatu.com>
Tested-by: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call trace observed during boot:
nest_capp0_imc performance monitor hardware support registered
nest_capp1_imc performance monitor hardware support registered
core_imc memory allocation for cpu 56 failed
Unable to handle kernel paging request for data at address 0xffa400010
Faulting instruction address: 0xc000000000bf3294
0:mon> e
cpu 0x0: Vector: 300 (Data Access) at [c000000ff38ff8d0]
pc: c000000000bf3294: mutex_lock+0x34/0x90
lr: c000000000bf3288: mutex_lock+0x28/0x90
sp: c000000ff38ffb50
msr: 9000000002009033
dar: ffa400010
dsisr: 80000
current = 0xc000000ff383de00
paca = 0xc000000007ae0000 softe: 0 irq_happened: 0x01
pid = 13, comm = cpuhp/0
Linux version 4.11.0-39.el7a.ppc64le (mockbuild@ppc-058.build.eng.bos.redhat.com) (gcc version 4.8.5 20150623 (Red Hat 4.8.5-16) (GCC) ) #1 SMP Tue Oct 3 07:42:44 EDT 2017
0:mon> t
[c000000ff38ffb80] c0000000002ddfac perf_pmu_migrate_context+0xac/0x470
[c000000ff38ffc40] c00000000011385c ppc_core_imc_cpu_offline+0x1ac/0x1e0
[c000000ff38ffc90] c000000000125758 cpuhp_invoke_callback+0x198/0x5d0
[c000000ff38ffd00] c00000000012782c cpuhp_thread_fun+0x8c/0x3d0
[c000000ff38ffd60] c0000000001678d0 smpboot_thread_fn+0x290/0x2a0
[c000000ff38ffdc0] c00000000015ee78 kthread+0x168/0x1b0
[c000000ff38ffe30] c00000000000b368 ret_from_kernel_thread+0x5c/0x74
While registering the cpuhoplug callbacks for core-imc, if we fails
in the cpuhotplug online path for any random core (either because opal call to
initialize the core-imc counters fails or because memory allocation fails for
that core), ppc_core_imc_cpu_offline() will get invoked for other cpus who
successfully returned from cpuhotplug online path.
But in the ppc_core_imc_cpu_offline() path we are trying to migrate the event
context, when core-imc counters are not even initialized. Thus creating the
above stack dump.
Add a check to see if core-imc counters are enabled or not in the cpuhotplug
offline path before migrating the context to handle this failing scenario.
Fixes: 885dcd709ba9 ("powerpc/perf: Add nest IMC PMU support")
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
For some odd historical reason, we preprocessed the linker scripts with
"-C", which keeps comments around. That makes no sense, since the
comments are not meaningful for the build anyway.
And it actually breaks things, since linker scripts can't have C++ style
"//" comments in them, so keeping comments after preprocessing now
limits us in odd and surprising ways in our header files for no good
reason.
The -C option goes back to pre-git and pre-bitkeeper times, but seems to
have been historically used (along with "-traditional") for some
odd-ball architectures (ia64, MIPS and SH). It probably didn't matter
back then either, but might possibly have been used to minimize the
difference between the original file and the pre-processed result.
The reason for this may be lost in time, but let's not perpetuate it
only because we can't remember why we did this crazy thing.
This was triggered by the recent addition of SPDX lines to the source
tree, where people apparently were confused about why header files
couldn't use the C++ comment format.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit 51204e0639c49ada02fd823782ad673b6326d748.
There wasn't really any good reason for it, and people are complaining
(rightly) that it broke existing practice.
Cc: Len Brown <len.brown@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Catalin Marinas:
"Check addr_limit in arm64 __dump_instr()"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: ensure __dump_instr() checks addr_limit
|
|
It's possible for a user to deliberately trigger __dump_instr with a
chosen kernel address.
Let's avoid problems resulting from this by using get_user() rather than
__get_user(), ensuring that we don't erroneously access kernel memory.
Where we use __dump_instr() on kernel text, we already switch to
KERNEL_DS, so this shouldn't adversely affect those cases.
Fixes: 60ffc30d5652810d ("arm64: Exception handling")
Cc: stable@vger.kernel.org
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/ARM Fixes for v4.14
- Fixes a number of issues with saving/restoring the ITS
- Fixes a bug in KVM/ARM when branch profiling is enabled in Hyp mode
- Fixes an emulation bug for 32-bit guests when injecting aborts
- Fixes a failure to check if a kmalloc succeeds in the ITS emulation
|
|
In kvm_apic_set_state() we update the hardware virtualized APIC after
the full APIC state has been overwritten. Do the same, when the full
APIC state has been reset in kvm_lapic_reset().
This updates some hardware state that was previously forgotten, as
far as I can tell. Also, this allows removing some APIC-related reset
code from vmx_vcpu_reset().
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Parts of the posted interrupt descriptor configure host behavior,
such as the notification vector and destination. Overwriting them
with zero as done during vCPU reset breaks posted interrupts.
KVM (re-)writes these fields on certain occasions and belatedly fixes
the situation in many cases. However, if you have a guest configured
with "idle=poll", for example, the fields might stay zero forever.
Do not reset the full descriptor in vmx_vcpu_reset(). Instead,
reset only the outstanding notifications and leave everything
else untouched.
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
kvm does not support setting the RTC, so the correct result is -ENODEV.
Returning -1 will cause sync_cmos_clock to keep trying to set the RTC
every second.
Signed-off-by: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fix from Shuah Khan:
"This consists of a single fix to a regression to printing individual
test results to the console. An earlier commit changed it to printing
just the summary of results, which will negatively impact users that
rely on console log to look at the individual test failures.
This fix makes it optional to print summary and by default results get
printed to the console"
* tag 'linux-kselftest-4.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: lib.mk: print individual test results to console by default
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Unfortunately we still have received a significant amount of changes
at the late stage, but at least all are small and clear fixes.
There are two fixes for ALSA core stuff, yet another timer race fix
and sequencer lockdep annotation fix. Both are spotted by syzkaller,
and not too serious but better to paper over quickly.
All other commits are about ASoC drivers, most notably, a revert of
RT5514 hotword control that was included in 4.14-rc (due to a kind of
abuse of kctl TLV ABI), together with topology API fixes and other
device-specific small fixes that should go for stable, too"
* tag 'sound-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: seq: Fix nested rwsem annotation for lockdep splat
ALSA: timer: Add missing mutex lock for compat ioctls
ASoC: rt5616: fix 0x91 default value
ASoC: rt5659: connect LOUT Amp with Charge Pump
ASoC: rt5659: register power bit of LOUT Amp
ASoC: rt5663: Change the dev getting function in rt5663_irq
ASoC: rt5514: Revert Hotword Model control
ASoC: topology: Fix a potential memory leak in 'soc_tplg_dapm_widget_denum_create()'
ASoC: topology: Fix a potential NULL pointer dereference in 'soc_tplg_dapm_widget_denum_create()'
ASoC: rt5514-spi: check irq status to schedule data copy
ASoC: adau17x1: Workaround for noise bug in ADC
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull key handling fixes from James Morris:
"Fixes for the Keys subsystem by Eric Biggers"
* 'fixes-v4.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: fix out-of-bounds read during ASN.1 parsing
KEYS: trusted: fix writing past end of buffer in trusted_read()
KEYS: return full count in keyring_read() if buffer is too small
|
|
In commit 30d6e0a4190d ("futex: Remove duplicated code and fix undefined
behaviour"), I let FUTEX_WAKE_OP to fail on invalid op. Namely when op
should be considered as shift and the shift is out of range (< 0 or > 31).
But strace's test suite does this madness:
futex(0x7fabd78bcffc, 0x5, 0xfacefeed, 0xb, 0x7fabd78bcffc, 0xa0caffee);
futex(0x7fabd78bcffc, 0x5, 0xfacefeed, 0xb, 0x7fabd78bcffc, 0xbadfaced);
futex(0x7fabd78bcffc, 0x5, 0xfacefeed, 0xb, 0x7fabd78bcffc, 0xffffffff);
When I pick the first 0xa0caffee, it decodes as:
0x80000000 & 0xa0caffee: oparg is shift
0x70000000 & 0xa0caffee: op is FUTEX_OP_OR
0x0f000000 & 0xa0caffee: cmp is FUTEX_OP_CMP_EQ
0x00fff000 & 0xa0caffee: oparg is sign-extended 0xcaf = -849
0x00000fff & 0xa0caffee: cmparg is sign-extended 0xfee = -18
That means the op tries to do this:
(futex |= (1 << (-849))) == -18
which is completely bogus. The new check of op in the code is:
if (encoded_op & (FUTEX_OP_OPARG_SHIFT << 28)) {
if (oparg < 0 || oparg > 31)
return -EINVAL;
oparg = 1 << oparg;
}
which results obviously in the "Invalid argument" errno:
FAIL: futex
===========
futex(0x7fabd78bcffc, 0x5, 0xfacefeed, 0xb, 0x7fabd78bcffc, 0xa0caffee) = -1: Invalid argument
futex.test: failed test: ../futex failed with code 1
So let us soften the failure to print only a (ratelimited) message, crop
the value and continue as if it were right. When userspace keeps up, we
can switch this to return -EINVAL again.
[v2] Do not return 0 immediatelly, proceed with the cropped value.
Fixes: 30d6e0a4190d ("futex: Remove duplicated code and fix undefined behaviour")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <dvhart@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
MIPS is no longer part of Imagination Technologies and my @imgtec.com
address will soon stop working. Update any files containing my address
as well as the .mailmap to point to my new @mips.com address.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/17579/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Many user space API headers have licensing information, which is either
incomplete, badly formatted or just a shorthand for referring to the
license under which the file is supposed to be. This makes it hard for
compliance tools to determine the correct license.
Update these files with an SPDX license identifier. The identifier was
chosen based on the license information in the file.
GPL/LGPL licensed headers get the matching GPL/LGPL SPDX license
identifier with the added 'WITH Linux-syscall-note' exception, which is
the officially assigned exception identifier for the kernel syscall
exception:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
This exception makes it possible to include GPL headers into non GPL
code, without confusing license compliance tools.
Headers which have either explicit dual licensing or are just licensed
under a non GPL license are updated with the corresponding SPDX
identifier and the GPLv2 with syscall exception identifier. The format
is:
((GPL-2.0 WITH Linux-syscall-note) OR SPDX-ID-OF-OTHER-LICENSE)
SPDX license identifiers are a legally binding shorthand, which can be
used instead of the full boiler plate text. The update does not remove
existing license information as this has to be done on a case by case
basis and the copyright holders might have to be consulted. This will
happen in a separate step.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
license
Many user space API headers are missing licensing information, which
makes it hard for compliance tools to determine the correct license.
By default are files without license information under the default
license of the kernel, which is GPLV2. Marking them GPLV2 would exclude
them from being included in non GPLV2 code, which is obviously not
intended. The user space API headers fall under the syscall exception
which is in the kernels COPYING file:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
otherwise syscall usage would not be possible.
Update the files which contain no license information with an SPDX
license identifier. The chosen identifier is 'GPL-2.0 WITH
Linux-syscall-note' which is the officially assigned identifier for the
Linux syscall exception. SPDX license identifiers are a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
syzkaller with KASAN reported an out-of-bounds read in
asn1_ber_decoder(). It can be reproduced by the following command,
assuming CONFIG_X509_CERTIFICATE_PARSER=y and CONFIG_KASAN=y:
keyctl add asymmetric desc $'\x30\x30' @s
The bug is that the length of an ASN.1 data value isn't validated in the
case where it is encoded using the short form, causing the decoder to
read past the end of the input buffer. Fix it by validating the length.
The bug report was:
BUG: KASAN: slab-out-of-bounds in asn1_ber_decoder+0x10cb/0x1730 lib/asn1_decoder.c:233
Read of size 1 at addr ffff88003cccfa02 by task syz-executor0/6818
CPU: 1 PID: 6818 Comm: syz-executor0 Not tainted 4.14.0-rc7-00008-g5f479447d983 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0xb3/0x10b lib/dump_stack.c:52
print_address_description+0x79/0x2a0 mm/kasan/report.c:252
kasan_report_error mm/kasan/report.c:351 [inline]
kasan_report+0x236/0x340 mm/kasan/report.c:409
__asan_report_load1_noabort+0x14/0x20 mm/kasan/report.c:427
asn1_ber_decoder+0x10cb/0x1730 lib/asn1_decoder.c:233
x509_cert_parse+0x1db/0x650 crypto/asymmetric_keys/x509_cert_parser.c:89
x509_key_preparse+0x64/0x7a0 crypto/asymmetric_keys/x509_public_key.c:174
asymmetric_key_preparse+0xcb/0x1a0 crypto/asymmetric_keys/asymmetric_type.c:388
key_create_or_update+0x347/0xb20 security/keys/key.c:855
SYSC_add_key security/keys/keyctl.c:122 [inline]
SyS_add_key+0x1cd/0x340 security/keys/keyctl.c:62
entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x447c89
RSP: 002b:00007fca7a5d3bd8 EFLAGS: 00000246 ORIG_RAX: 00000000000000f8
RAX: ffffffffffffffda RBX: 00007fca7a5d46cc RCX: 0000000000447c89
RDX: 0000000020006f4a RSI: 0000000020006000 RDI: 0000000020001ff5
RBP: 0000000000000046 R08: fffffffffffffffd R09: 0000000000000000
R10: 0000000000000002 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000000 R14: 00007fca7a5d49c0 R15: 00007fca7a5d4700
Fixes: 42d5ec27f873 ("X.509: Add an ASN.1 decoder")
Cc: <stable@vger.kernel.org> # v3.7+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
When calling keyctl_read() on a key of type "trusted", if the
user-supplied buffer was too small, the kernel ignored the buffer length
and just wrote past the end of the buffer, potentially corrupting
userspace memory. Fix it by instead returning the size required, as per
the documentation for keyctl_read().
We also don't even fill the buffer at all in this case, as this is
slightly easier to implement than doing a short read, and either
behavior appears to be permitted. It also makes it match the behavior
of the "encrypted" key type.
Fixes: d00a1c72f7f4 ("keys: add new trusted key-type")
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Cc: <stable@vger.kernel.org> # v2.6.38+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Commit e645016abc80 ("KEYS: fix writing past end of user-supplied buffer
in keyring_read()") made keyring_read() stop corrupting userspace memory
when the user-supplied buffer is too small. However it also made the
return value in that case be the short buffer size rather than the size
required, yet keyctl_read() is actually documented to return the size
required. Therefore, switch it over to the documented behavior.
Note that for now we continue to have it fill the short buffer, since it
did that before (pre-v3.13) and dump_key_tree_aux() in keyutils arguably
relies on it.
Fixes: e645016abc80 ("KEYS: fix writing past end of user-supplied buffer in keyring_read()")
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains two one-liner fixes for your net tree,
they are:
1) Disable fast hash operations for 2-bytes length keys which is leading
to incorrect lookups in nf_tables, from Anatole Denis.
2) Reload pointer ipv4 header after ip_route_me_harder() given this may
result in use-after-free due to skbuff header reallocation, patch
from Tejaswi Tanikella.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FRA_L3MDEV is defined as U8, but is being added as a U32 attribute. On
big endian architecture, this results in the l3mdev entry not being
added to the FIB rules.
Fixes: 1aa6c4f6b8cd8 ("net: vrf: Add l3mdev rules on first device create")
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Average RTT could become zero. This happened in real life at least twice.
This patch treats zero as 1us.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Lawrence Brakmo <Brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
into drm-fixes
Just two small patches for stable to fix the driver failing to load on polaris
cards with harvested VCE or UVD blocks.
* 'drm-fixes-4.14' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: allow harvesting check for Polaris VCE
drm/amdgpu: return -ENOENT from uvd 6.0 early init for harvesting
|
|
Fixes init failures on Polaris cards with harvested
VCE blocks.
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Fixes init failures on polaris cards with harvested UVD.
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Fixes for Stable:
- Fix KBL Blank Screen (Jani)
- Fix FIFO Underrun on SNB (Maarten)
Other fixes:
- Fix GPU Hang on i915gm (Chris)
- Fix gem_tiled_pread_pwrite IGT case (Chris)
- Cancel modeset retry work during modeset clean-up (Manasi)
* tag 'drm-intel-fixes-2017-11-01' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Check incoming alignment for unfenced buffers (on i915gm)
drm/i915: Hold rcu_read_lock when iterating over the radixtree (vma idr)
drm/i915: Hold rcu_read_lock when iterating over the radixtree (objects)
drm/i915/edp: read edp display control registers unconditionally
drm/i915: Do not rely on wm preservation for ILK watermarks
drm/i915: Cancel the modeset retry work during modeset cleanup
|
|
Add an additional symbol to the decompressor image, which will allow
future debugging of non-bootable problems similar to the one encountered
with the EFI stub.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The smp-cmp build has been (further) broken since commit 856fbcee6099
("MIPS: Store core & VP IDs in GlobalNumber-style variable") in
v4.14-rc1 like so:
arch/mips/kernel/smp-cmp.c: In function ‘cmp_init_secondary’:
arch/mips/kernel/smp-cmp.c:53:4: error: ‘struct cpuinfo_mips’ has no member named ‘vpe_id’
c->vpe_id = (read_c0_tcbind() >> TCBIND_CURVPE_SHIFT) &
^
Fix by replacing vpe_id with cpu_set_vpe_id().
Fixes: 856fbcee6099 ("MIPS: Store core & VP IDs in GlobalNumber-style variable")
Signed-off-by: James Hogan <jhogan@kernel.org>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17569/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull signal bugfix from Eric Biederman:
"When making the generic support for SIGEMT conditional on the presence
of SIGEMT I made a typo that causes it to fail to activate. It was
noticed comparatively quickly but the bug report just made it to me
today"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
signal: Fix name of SIGEMT in #if defined() check
|
|
Neither of the current maintainers works for Imagination any more.
Removed both imgtec email addresses and added back mine for
occasional reviews, also changed from Maintained to Odd Fixes to
reflect the time that I will be able to spend on it.
Signed-off-by: James Hartley <james.hartley@sondrel.com>
Patchwork: https://patchwork.linux-mips.org/patch/17475/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
When task_struct was moved, this MIPS code was neglected. Evidently
nobody is using it anymore. This fixes this build error:
In file included from ./arch/mips/include/asm/thread_info.h:15:0,
from ./include/linux/thread_info.h:37,
from ./include/asm-generic/current.h:4,
from ./arch/mips/include/generated/asm/current.h:1,
from ./include/linux/sched.h:11,
from arch/mips/kernel/smp-cmp.c:22:
arch/mips/kernel/smp-cmp.c: In function ‘cmp_boot_secondary’:
./arch/mips/include/asm/processor.h:384:41: error: implicit declaration
of function ‘task_stack_page’ [-Werror=implicit-function-declaration]
#define __KSTK_TOS(tsk) ((unsigned long)task_stack_page(tsk) + \
^
arch/mips/kernel/smp-cmp.c:84:21: note: in expansion of macro ‘__KSTK_TOS’
unsigned long sp = __KSTK_TOS(idle);
^~~~~~~~~~
Fixes: f3ac60671954 ("sched/headers: Move task-stack related APIs from <linux/sched.h> to <linux/sched/task_stack.h>")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: <stable@vger.kernel.org> # 4.11+
Patchwork: https://patchwork.linux-mips.org/patch/17522/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Commit cc731525f26a ("signal: Remove kernel interal si_code magic")
added a check for SIGMET and NSIGEMT being defined. That SIGMET should
in fact be SIGEMT, with SIGEMT being defined in
arch/{alpha,mips,sparc}/include/uapi/asm/signal.h
This was actually pointed out by BenHutchings in a lwn.net comment
here https://lwn.net/Comments/734608/
Fixes: cc731525f26a ("signal: Remove kernel interal si_code magic")
Signed-off-by: Andrew Clayton <andrew@digital-domain.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
Pull block fixes from Jens Axboe:
"A few fixes that should go into this series:
- Regression fix for ide-cd, ensuring that a request is fully
initialized. From Hongxu.
- Ditto fix for virtio_blk, from Bart.
- NVMe fix from Keith, ensuring that we set the right block size on
revalidation. If the block size changed, we'd be in trouble without
it.
- NVMe rdma fix from Sagi, fixing a potential hang while the
controller is being removed"
* 'for-linus' of git://git.kernel.dk/linux-block:
ide:ide-cd: fix kernel panic resulting from missing scsi_req_init
nvme: Fix setting logical block format when revalidating
virtio_blk: Fix an SG_IO regression
nvme-rdma: fix possible hang when issuing commands during ctrl removal
|
|
Change all relevant instances of miodrag.dinic@imgtec.com
email address to miodrag.dinic@mips.com.
Signed-off-by: Miodrag Dinic <miodrag.dinic@mips.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/17515/
[jhogan@kernel.org: Fix .mailmap direction]
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Change all relevant instances of aleksandar.markovic@imgtec.com
email address to aleksandar.markovic@mips.com.
Signed-off-by: Miodrag Dinic <miodrag.dinic@mips.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/17514/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Commit 1ec9dd80bedc ("MIPS: CPS: Detect CPUs in secondary clusters")
added a check in cps_boot_secondary() that the secondary being booted is
in the same cluster as the CPU running this code. This check is
performed using current_cpu_data without disabling preemption. As such
when CONFIG_PREEMPT=y, a BUG is triggered:
[ 57.991693] BUG: using smp_processor_id() in preemptible [00000000] code: hotplug/1749
<snip>
[ 58.063077] Call Trace:
[ 58.065842] [<8040cdb4>] show_stack+0x84/0x114
[ 58.070830] [<80b11b38>] dump_stack+0xf8/0x140
[ 58.075796] [<8079b12c>] check_preemption_disabled+0xec/0x118
[ 58.082204] [<80415110>] cps_boot_secondary+0x84/0x44c
[ 58.087935] [<80413a14>] __cpu_up+0x34/0x98
[ 58.092624] [<80434240>] bringup_cpu+0x38/0x114
[ 58.097680] [<80434af0>] cpuhp_invoke_callback+0x168/0x8f0
[ 58.103801] [<804362d0>] _cpu_up+0x154/0x1c8
[ 58.108565] [<804363dc>] do_cpu_up+0x98/0xa8
[ 58.113333] [<808261f8>] device_online+0x84/0xc0
[ 58.118481] [<80826294>] online_store+0x60/0x98
[ 58.123562] [<8062261c>] kernfs_fop_write+0x158/0x1d4
[ 58.129196] [<805a2ae4>] __vfs_write+0x4c/0x168
[ 58.134247] [<805a2dc8>] vfs_write+0xe0/0x190
[ 58.139095] [<805a2fe0>] SyS_write+0x68/0xc4
[ 58.143854] [<80415d58>] syscall_common+0x34/0x58
In reality we don't currently support running the kernel on CPUs not in
cluster 0, so the answer to cpu_cluster(¤t_cpu_data) will always
be 0, even if this task being preempted and continues running on a
different CPU. Regardless, the BUG should not be triggered, so fix this
by switching to raw_current_cpu_data. When multicluster support lands
upstream this check will need removing or changing anyway.
Fixes: 1ec9dd80bedc ("MIPS: CPS: Detect CPUs in secondary clusters")
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Reviewed-by: Paul Burton <paul.burton@mips.com>
CC: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17563/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Jeremy reported a suspicious RCU usage warning in mcelog.
/dev/mcelog is called in process context now as part of the notifier
chain and doesn't need any of the fancy RCU and lockless accesses which
it did in atomic context.
Axe it all in favor of a simple mutex synchronization which cures the
problem reported.
Fixes: 5de97c9f6d85 ("x86/mce: Factor out and deprecate the /dev/mcelog driver")
Reported-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-and-tested-by: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: linux-edac@vger.kernel.org
Cc: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20171101164754.xzzmskl4ngrqc5br@pd.tnic
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1498969
|
|
Guenter reported:
There is still a problem. When running
echo 6 > /proc/sys/kernel/watchdog_thresh
echo 5 > /proc/sys/kernel/watchdog_thresh
repeatedly, the message
NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
stops after a while (after ~10-30 iterations, with fluctuations).
Maybe watchdog_cpus needs to be atomic ?
That's correct as this again is affected by the asynchronous nature of the
smpboot thread unpark mechanism.
CPU 0 CPU1 CPU2
write(watchdog_thresh, 6)
stop()
park()
update()
start()
unpark()
thread->unpark()
cnt++;
write(watchdog_thresh, 5) thread->unpark()
stop()
park() thread->park()
cnt--; cnt++;
update()
start()
unpark()
That's not a functional problem, it just affects the informational message.
Convert watchdog_cpus to atomic_t to prevent the problem
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20171101181126.j727fqjmdthjz4xk@redhat.com
|
|
Simplify deferred event destroy")
Guenter reported a crash in the watchdog/perf code, which is caused by
cleanup() and enable() running concurrently. The reason for this is:
The watchdog functions are serialized via the watchdog_mutex and cpu
hotplug locking, but the enable of the perf based watchdog happens in
context of the unpark callback of the smpboot thread. But that unpark
function is not synchronous inside the locking. The unparking of the thread
just wakes it up and leaves so there is no guarantee when the thread is
executing.
If it starts running _before_ the cleanup happened then it will create a
event and overwrite the dead event pointer. The new event is then cleaned
up because the event is marked dead.
lock(watchdog_mutex);
lockup_detector_reconfigure();
cpus_read_lock();
stop();
park()
update();
start();
unpark()
cpus_read_unlock(); thread runs()
overwrite dead event ptr
cleanup();
free new event, which is active inside perf....
unlock(watchdog_mutex);
The park side is safe as that actually waits for the thread to reach
parked state.
Commit a33d44843d45 removed the protection against this kind of scenario
under the stupid assumption that the hotplug serialization and the
watchdog_mutex cover everything.
Bring it back.
Reverts: a33d44843d45 ("watchdog/hardlockup/perf: Simplify deferred event destroy")
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Feels-stupid Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Don Zickus <dzickus@redhat.com>
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1710312145190.1942@nanos
|
|
ARM depends on the macros '__ARMEL__' & '__ARMEB__' being defined
or not to correctly select or define endian-specific macros,
structures or pieces of code.
These macros are predefined by the compiler but sparse knows
nothing about them and thus may pre-process files differently
from what gcc would.
Fix this by passing '-D__ARMEL__' or '-D__ARMEB__' to sparse,
depending on the endianness of the kernel, like defined by GCC.
Note: In most case it won't change anything since most ARMs use
little-endian (but an allyesconfig would use big-endian!).
To: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
In case the object has changed tiling between calls to execbuf, we need
to check if the existing offset inside the GTT matches the new tiling
constraint. We even need to do this for "unfenced" tiled objects, where
the 3D commands use an implied fence and so the object still needs to
match the physical fence restrictions on alignment (only required for
gen2 and early gen3).
In commit 2889caa92321 ("drm/i915: Eliminate lots of iterations over
the execobjects array"), the idea was to remove the second guessing and
only set the NEEDS_MAP flag when required. However, the entire check
for an unusable offset for fencing was removed and not just the
secondary check. I.e.
/* avoid costly ping-pong once a batch bo ended up non-mappable */
if (entry->flags & __EXEC_OBJECT_NEEDS_MAP &&
!i915_vma_is_map_and_fenceable(vma))
return !only_mappable_for_reloc(entry->flags);
was entirely removed as the ping-pong between execbuf passes was fixed,
but its primary purpose in forcing unaligned unfenced access to be
rebound was forgotten.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103502
Fixes: 2889caa92321 ("drm/i915: Eliminate lots of iterations over the execobjects array")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031103607.17836-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit 1d033beb20d6d5885587a02a393b6598d766a382)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.14
A bunch of fixes here, mostly device specific ones (the biggest one
being the revert of the hotword support for rt5514), with a couple of
core fixes for potential issues with corrupted or otherwise invalid
topology files.
|
