| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 97eda5dcc2cde5dcc778bef7a9344db3b6bf8ef5 ]
When STMFX supply is stopped, spurious interrupt can occur. To avoid that,
disable the interrupt in suspend before disabling the regulator and
re-enable it at the end of resume.
Fixes: 06252ade9156 ("mfd: Add ST Multi-Function eXpander (STMFX) core driver")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 60c2c4bcb9202acad4cc26af20b44b6bd7874f7b ]
In case the interrupt signal can't be configured, IRQ domain needs to be
removed.
Fixes: 06252ade9156 ("mfd: Add ST Multi-Function eXpander (STMFX) core driver")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e583649d87ec090444aa5347af0927cd6e8581ae ]
STMFX supply is disabled during suspend. To avoid a too early access to
the STMFX firmware on resume, reset the chip and wait for its firmware to
be loaded.
Fixes: 06252ade9156 ("mfd: Add ST Multi-Function eXpander (STMFX) core driver")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit de308d1815c9e8fe602a958c5c76142ff6501d75 ]
The commit
c84cb3735fd5 ("x86/apic: Move TSC deadline timer debug printk")
removed the message which said that the deadline timer was enabled.
It added a pr_debug() message which is issued when deadline timer
validation succeeds.
Well, issued only when CONFIG_DYNAMIC_DEBUG is enabled - otherwise
pr_debug() calls get optimized away if DEBUG is not defined in the
compilation unit.
Therefore, make the above message pr_info() so that it is visible in
dmesg.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200525104218.27018-1-bp@alien8.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 49ea0c036ede81f126f1a9389d377999fdf5c5a1 ]
Remove device specific debugfs entries immediately if LLD detaches a
particular ULD device in case of fatal PCI errors.
Link: https://lore.kernel.org/r/20200524190814.17599-1-bharat@chelsio.com
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5967577231f9b19acd5a59485e9075964065bbe3 ]
Misuse of CONFIG_* in UAPI headers should result in an error. These config
options can be set in userspace by the user application which includes
these headers to control the APIs and structures being used in a kernel
which supports multiple targets.
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5d363120aa548ba52d58907a295eee25f8207ed2 ]
This patch adds new config_ep_by_speed_and_alt function which
extends the config_ep_by_speed about alt parameter.
This additional parameter allows to find proper usb_ss_ep_comp_descriptor.
Problem has appeared during testing f_tcm (BOT/UAS) driver function.
f_tcm function for SS use array of headers for both BOT/UAS alternate
setting:
static struct usb_descriptor_header *uasp_ss_function_desc[] = {
(struct usb_descriptor_header *) &bot_intf_desc,
(struct usb_descriptor_header *) &uasp_ss_bi_desc,
(struct usb_descriptor_header *) &bot_bi_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_ss_bo_desc,
(struct usb_descriptor_header *) &bot_bo_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_intf_desc,
(struct usb_descriptor_header *) &uasp_ss_bi_desc,
(struct usb_descriptor_header *) &uasp_bi_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_bi_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_bo_desc,
(struct usb_descriptor_header *) &uasp_bo_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_bo_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_status_desc,
(struct usb_descriptor_header *) &uasp_status_in_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_status_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_cmd_desc,
(struct usb_descriptor_header *) &uasp_cmd_comp_desc,
(struct usb_descriptor_header *) &uasp_cmd_pipe_desc,
NULL,
};
The first 5 descriptors are associated with BOT alternate setting,
and others are associated with UAS.
During handling UAS alternate setting f_tcm driver invokes
config_ep_by_speed and this function sets incorrect companion endpoint
descriptor in usb_ep object.
Instead setting ep->comp_desc to uasp_bi_ep_comp_desc function in this
case set ep->comp_desc to uasp_ss_bi_desc.
This is due to the fact that it searches endpoint based on endpoint
address:
for_each_ep_desc(speed_desc, d_spd) {
chosen_desc = (struct usb_endpoint_descriptor *)*d_spd;
if (chosen_desc->bEndpoitAddress == _ep->address)
goto ep_found;
}
And in result it uses the descriptor from BOT alternate setting
instead UAS.
Finally, it causes that controller driver during enabling endpoints
detect that just enabled endpoint for bot.
Signed-off-by: Jayshri Pawar <jpawar@cadence.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 44734a594196bf1d474212f38fe3a0d37a73278b ]
m66592_free_request() is called under label "err_add_udc"
and "clean_up", and m66592->ep0_req is not set to NULL after
first free, leading to a double-free. Fix this issue by
setting m66592->ep0_req to NULL after the first free.
Fixes: 0f91349b89f3 ("usb: gadget: convert all users to the new udc infrastructure")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eafa80041645cd7604c4357b1a0cd4a3c81f2227 ]
Currently pointer ep is being dereferenced before it is null checked
leading to a null pointer dereference issue. Fix this by only assigning
pointer udc once ep is known to be not null. Also remove a debug
message that requires a valid udc which may not be possible at that
point.
Addresses-Coverity: ("Dereference before null check")
Fixes: 24a28e428351 ("USB: gadget driver for LPC32xx")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7a0fbcf7c308920bc6116b3a5fb21c8cc5fec128 ]
Clang warns:
drivers/usb/gadget/udc/s3c2410_udc.c:255:11: warning: comparison of
address of 'ep->queue' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (&ep->queue == NULL)
~~~~^~~~~ ~~~~
1 warning generated.
It is not wrong, queue is not a pointer so if ep is not NULL, the
address of queue cannot be NULL. No other driver does a check like this
and this check has been around since the driver was first introduced,
presumably with no issues so it does not seem like this check should be
something else. Just remove it.
Commit afe956c577b2d ("kbuild: Enable -Wtautological-compare") exposed
this but it is not the root cause of the warning.
Fixes: 3fc154b6b8134 ("USB Gadget driver for Samsung s3c2410 ARM SoC")
Link: https://github.com/ClangBuiltLinux/linux/issues/1004
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8c935deacebb8fac8f41378701eb79d12f3c2e2d ]
When the remote wakeup interrupt is triggered, lx_state is resumed from L2
to L0 state. But when the gadget resume is called, lx_state is still L2.
This prevents the resume callback to queue any request. Any attempt
to queue a request from resume callback will result in:
- "submit request only in active state" debug message to be issued
- dwc2_hsotg_ep_queue() returns -EAGAIN
Call the gadget resume routine after the core is in L0 state.
Fixes: f81f46e1f530 ("usb: dwc2: implement hibernation during bus suspend/resume")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a0948ddba65f4f6d3cfb5e2b84685485d0452966 ]
There is actually no need to ping the watchdog before disabling it
during timeout change. Disabling the watchdog already takes care of
resetting the counter.
This fixes an issue during boot when the userspace watchdog handler takes
over and the watchdog is already running. Opening the watchdog in this case
leads to the first ping and directly after that without the required
heartbeat delay a second ping issued by the set_timeout call. Due to the
missing delay this resulted in a reset.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20200403130728.39260-3-s.riedmueller@phytec.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 63a3345c2d42a9b29e1ce2d3a4043689b3995cea ]
The allocated ports structure in never freed. The free function should be
called by release_cma_ports_group, but the group is never released since
we don't remove its default group.
Remove default groups when device group is deleted.
Fixes: 045959db65c6 ("IB/cma: Add configfs for rdma_cm")
Link: https://lore.kernel.org/r/20200521072650.567908-1-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 87dccf09323fc363bd0d072fcc12b96622ab8c69 ]
The vim3l board does not work with a standard PCIe switch (ASM1184e),
spitting all kind of errors - hinting at HW misconfiguration (no link,
port enumeration issues, etc).
According to the the Synopsys DWC PCIe Reference Manual, in the section
dedicated to the PLCR register, bit 7 is described (FAST_LINK_MODE) as:
"Sets all internal timers to fast mode for simulation purposes."
it is sound to set this bit from a simulation perspective, but on actual
silicon, which expects timers to have a nominal value, it is not.
Make sure the FAST_LINK_MODE bit is cleared when configuring the RC
to solve this problem.
Link: https://lore.kernel.org/r/20200429164230.309922-1-maz@kernel.org
Fixes: 9c0ef6d34fdb ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver")
Signed-off-by: Marc Zyngier <maz@kernel.org>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0414b93e78d87ecc24ae1a7e61fe97deb29fa2f4 ]
On a system that uses the internal DWC MSI widget, I get this
warning from debugfs when CONFIG_GENERIC_IRQ_DEBUGFS is selected:
debugfs: File ':soc:pcie@fc000000' in directory 'domains' already present!
This is due to the fact that the DWC MSI code tries to register two
IRQ domains for the same firmware node, without telling the low
level code how to distinguish them (by setting a bus token). This
further confuses debugfs which tries to create corresponding
files for each domain.
Fix it by tagging the inner domain as DOMAIN_BUS_NEXUS, which is
the closest thing we have as to "generic MSI".
Link: https://lore.kernel.org/r/20200501113921.366597-1-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7b38fd9760f51cc83d80eed2cfbde8b5ead9e93a ]
Except for Endpoints, we enable PTM at enumeration-time. Previously we did
not account for the fact that Switch Downstream Ports are not permitted to
have a PTM capability; their PTM behavior is controlled by the Upstream
Port (PCIe r5.0, sec 7.9.16). Since Downstream Ports don't have a PTM
capability, we did not mark them as "ptm_enabled", which meant that
pci_enable_ptm() on an Endpoint failed because there was no PTM path to it.
Mark Downstream Ports as "ptm_enabled" if their Upstream Port has PTM
enabled.
Fixes: eec097d43100 ("PCI: Add pci_enable_ptm() for drivers to enable PTM on endpoints")
Reported-by: Aditya Paluri <Venkata.AdityaPaluri@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 489dc0f06a5837f87482c0ce61d830d24e17082e ]
The only case where dmz_get_zone_for_reclaim() cannot return a zone is
if the respective lists are empty. So we should just return a simple
NULL value here as we really don't have an error code which would make
sense.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c2e929b18cea6cbf71364f22d742d9aad7f4677a ]
Booting a power9 server with hash MMU could trigger an undefined
behaviour because pud_offset(p4d, 0) will do,
0 >> (PAGE_SHIFT:16 + PTE_INDEX_SIZE:8 + H_PMD_INDEX_SIZE:10)
Fix it by converting pud_index() and friends to static inline
functions.
UBSAN: shift-out-of-bounds in arch/powerpc/mm/ptdump/ptdump.c:282:15
shift exponent 34 is too large for 32-bit type 'int'
CPU: 6 PID: 1 Comm: swapper/0 Not tainted 5.6.0-rc4-next-20200303+ #13
Call Trace:
dump_stack+0xf4/0x164 (unreliable)
ubsan_epilogue+0x18/0x78
__ubsan_handle_shift_out_of_bounds+0x160/0x21c
walk_pagetables+0x2cc/0x700
walk_pud at arch/powerpc/mm/ptdump/ptdump.c:282
(inlined by) walk_pagetables at arch/powerpc/mm/ptdump/ptdump.c:311
ptdump_check_wx+0x8c/0xf0
mark_rodata_ro+0x48/0x80
kernel_init+0x74/0x194
ret_from_kernel_thread+0x5c/0x74
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20200306044852.3236-1-cai@lca.pw
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3482a7afb261e2de9269a7f9ad0f4a3a82a83a53 ]
Fix flag in PCIe controllers device-tree nodes 'ranges' property to correctly
represent 64-bit resources.
Fixes: 2602c32f15e7 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra194 DT")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bba25915b172c72f6fa635f091624d799e3c9cae ]
The 'phy-mode' property is currently defined as 'rgmii' for Jetson
Xavier. This indicates that the RGMII RX and TX delays are set by the
MAC and the internal delays set by the PHY are not used.
If the Marvell PHY driver is enabled, such that it is used and not the
generic PHY, ethernet failures are seen (DHCP is failing to obtain an
IP address) and this is caused because the Marvell PHY driver is
disabling the internal RX and TX delays. For Jetson Xavier the internal
PHY RX and TX delay should be used and so fix this by setting the
'phy-mode' to 'rgmii-id' and not 'rgmii'.
Fixes: f89b58ce71a9 ("arm64: tegra: Add ethernet controller on Tegra194")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9b46418c40fe910e6537618f9932a8be78a3dd6c ]
After the copy operation completes the cache is not up-to-date. Truncate
all pages in the interval that has successfully been copied.
Truncating completely copied dirty pages is okay, since the data has been
overwritten anyway. Truncating partially copied dirty pages is not okay;
add a comment for now.
Fixes: 88bc7d5097a1 ("fuse: add support for copy_file_range()")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2c4656dfd994538176db30ce09c02cc0dfc361ae ]
a) Dirty cache needs to be written back not just in the writeback_cache
case, since the dirty pages may come from memory maps.
b) The fuse_writeback_range() helper takes an inclusive interval, so the
end position needs to be pos+len-1 instead of pos+len.
Fixes: 88bc7d5097a1 ("fuse: add support for copy_file_range()")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 89f12d6509bff004852c51cb713a439a86816b24 ]
'chan_name' is malloced in imx_scu_probe() and should be freed
before leaving from the error handling cases, otherwise it will
cause memory leak.
Fixes: edbee095fafb ("firmware: imx: add SCU firmware driver support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 61fb2482216679b9e1e797440c148bb143a5040a ]
When tcmu queues a new command - no matter whether in command ring or in
qfull_queue - a cmd_id from IDR udev->commands is assigned to the command.
If userspace sends a wrong command completion containing the cmd_id of a
command on the qfull_queue, tcmu_handle_completions() finds the command in
the IDR and calls tcmu_handle_completion() for it. This might do some nasty
things because commands in qfull_queue do not have a valid dbi list.
To fix this bug, we no longer add queued commands to the idr. Instead the
cmd_id is assign when a command is written to the command ring.
Due to this change I had to adapt the source code at several places where
up to now an idr_for_each had been done.
[mkp: fix checkpatch warnings]
Link: https://lore.kernel.org/r/20200518164833.12775-1-bstroesser@ts.fujitsu.com
Acked-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 441c88d5b3ff80108ff536c6cf80591187015403 ]
The firmware has reduced the number of descriptions of command
HNS_ROCE_OPC_QUERY_PF_TIMER_RES to 1. The driver needs to adapt, otherwise
the hardware will report error 4(CMD_NEXT_ERR).
Fixes: 0e40dc2f70cd ("RDMA/hns: Add timer allocation support for hip08")
Link: https://lore.kernel.org/r/1588931159-56875-3-git-send-email-liweihang@huawei.com
Signed-off-by: Lang Cheng <chenglang@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 349be276509455ac2f19fa4051ed773082c6a27e ]
The qkey queried through the query ud qp verb is a fixed value and it
should be read from qp context.
Fixes: 926a01dc000d ("RDMA/hns: Add QP operations support for hip08 SoC")
Link: https://lore.kernel.org/r/1588931159-56875-2-git-send-email-liweihang@huawei.com
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 25bdae0f1c6609ceaf55fe6700654f0be2253d8e ]
Mark the SCLK clock for Exynos5433 I2S1 device with IGNORE_UNUSED flag to
match its behaviour with SCLK clock for AUD_I2S (I2S0) device until
a proper fix for Exynos I2S driver is ready.
This fixes the following synchronous abort issue revealed by the probe
order change caused by the commit 93d2e4322aa7 ("of: platform: Batch
fwnode parsing when adding all top level devices")
Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 50 Comm: kworker/0:1 Not tainted 5.7.0-rc5+ #701
Hardware name: Samsung TM2E board (DT)
Workqueue: events deferred_probe_work_func
pstate: 60000005 (nZCv daif -PAN -UAO)
pc : samsung_i2s_probe+0x768/0x8f0
lr : samsung_i2s_probe+0x688/0x8f0
...
Call trace:
samsung_i2s_probe+0x768/0x8f0
platform_drv_probe+0x50/0xa8
really_probe+0x108/0x370
driver_probe_device+0x54/0xb8
__device_attach_driver+0x90/0xc0
bus_for_each_drv+0x70/0xc8
__device_attach+0xdc/0x140
device_initial_probe+0x10/0x18
bus_probe_device+0x94/0xa0
deferred_probe_work_func+0x70/0xa8
process_one_work+0x2a8/0x718
worker_thread+0x48/0x470
kthread+0x134/0x160
ret_from_fork+0x10/0x1c
Code: 17ffffaf d503201f f94086c0 91003000 (88dffc00)
---[ end trace ccf721c9400ddbd6 ]---
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c9d7e3da1f3c4cf5dddfc5d7ce4d76d013aba1cc ]
Corrected error handling goto sequnece. Level put_pages should
be called when pinned pages >= 0 && pinned != npages. Level
free_pages should be called when pinned pages < 0.
Fixes: fa8dda1edef9 ("fpga: dfl: afu: add DFL_FPGA_PORT_DMA_MAP/UNMAP ioctls support")
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Acked-by: Wu Hao <hao.wu@intel.com>
Reviewed-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/1589825991-3545-1-git-send-email-jrdr.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4dd31f1ffec6c370c3c2e0c605628bf5e16d5c46 ]
When submitting the previous fix "tty: n_gsm: Fix waking up upper tty
layer when room available". It was suggested to switch from a while to
a for loop, but when doing it, there was a remaining bogus i++.
This patch removes this i++ and also reorganizes the code making it more
compact.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200518084517.2173242-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d49292025f79693d3348f8e2029a8b4703be0f0a ]
The function ehci_mxc_drv_probe() does not perform sufficient error
checking after executing platform_get_irq(), thus fix it.
Fixes: 7e8d5cd93fac ("USB: Add EHCI support for MX27 and MX31 based boards")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200513132647.5456-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0e0e10fde0e9808d1991268f5dca69fb36c025f7 ]
The Toshiba Encore WT8-A tablet almost fully works with the default
settings for non-CR Bay Trail devices. The only problem is that its
jack-detect switch is not inverted (it is active high instead of
the normal active low).
Add a quirk for this model using the default settings +
BYT_RT5640_JD_NOT_INV.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200518072416.5348-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e4337877c5d578722c0716f131fb774522013cf5 ]
When allocation for mdp5_kms fails, calling mdp5_destroy() leads to undefined
behaviour, likely a nullptr exception or use-after-free troubles.
Signed-off-by: Roy Spliet <nouveau@spliet.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1cb3b0095c3d0bb96912bfbbce4fc006d41f367c ]
The following warning was observed when attempting to suspend to disk
using a USB flash as a swap device.
[ 111.779649] ------------[ cut here ]------------
[ 111.788382] URB (____ptrval____) submitted while active
[ 111.796646] WARNING: CPU: 3 PID: 365 at drivers/usb/core/urb.c:363 usb_submit_urb+0x3d8/0x590
[ 111.805417] Modules linked in:
[ 111.808584] CPU: 3 PID: 365 Comm: kworker/3:2 Not tainted 5.6.0-rc6-00002-gdfd1731f9a3e-dirty #545
[ 111.817796] Hardware name: ARM Juno development board (r2) (DT)
[ 111.823896] Workqueue: usb_hub_wq hub_event
[ 111.828217] pstate: 60000005 (nZCv daif -PAN -UAO)
[ 111.833156] pc : usb_submit_urb+0x3d8/0x590
[ 111.837471] lr : usb_submit_urb+0x3d8/0x590
[ 111.841783] sp : ffff800018de38b0
[ 111.845205] x29: ffff800018de38b0 x28: 0000000000000003
[ 111.850682] x27: ffff000970530b20 x26: ffff8000133fd000
[ 111.856159] x25: ffff8000133fd000 x24: ffff800018de3b38
[ 111.861635] x23: 0000000000000004 x22: 0000000000000c00
[ 111.867112] x21: 0000000000000000 x20: 00000000fffffff0
[ 111.872589] x19: ffff0009704e7a00 x18: ffffffffffffffff
[ 111.878065] x17: 00000000a7c8f4bc x16: 000000002af33de8
[ 111.883542] x15: ffff8000133fda88 x14: 0720072007200720
[ 111.889019] x13: 0720072007200720 x12: 0720072007200720
[ 111.894496] x11: 0000000000000000 x10: 00000000a5286134
[ 111.899973] x9 : 0000000000000002 x8 : ffff000970c837a0
[ 111.905449] x7 : 0000000000000000 x6 : ffff800018de3570
[ 111.910926] x5 : 0000000000000001 x4 : 0000000000000003
[ 111.916401] x3 : 0000000000000000 x2 : ffff800013427118
[ 111.921879] x1 : 9d4e965b4b7d7c00 x0 : 0000000000000000
[ 111.927356] Call trace:
[ 111.929892] usb_submit_urb+0x3d8/0x590
[ 111.933852] hub_activate+0x108/0x7f0
[ 111.937633] hub_resume+0xac/0x148
[ 111.941149] usb_resume_interface.isra.10+0x60/0x138
[ 111.946265] usb_resume_both+0xe4/0x140
[ 111.950225] usb_runtime_resume+0x24/0x30
[ 111.954365] __rpm_callback+0xdc/0x138
[ 111.958236] rpm_callback+0x34/0x98
[ 111.961841] rpm_resume+0x4a8/0x720
[ 111.965445] rpm_resume+0x50c/0x720
[ 111.969049] __pm_runtime_resume+0x4c/0xb8
[ 111.973276] usb_autopm_get_interface+0x28/0x60
[ 111.977948] hub_event+0x80/0x16d8
[ 111.981466] process_one_work+0x2a4/0x748
[ 111.985604] worker_thread+0x48/0x498
[ 111.989387] kthread+0x13c/0x140
[ 111.992725] ret_from_fork+0x10/0x18
[ 111.996415] irq event stamp: 354
[ 111.999756] hardirqs last enabled at (353): [<ffff80001019ea1c>] console_unlock+0x504/0x5b8
[ 112.008441] hardirqs last disabled at (354): [<ffff8000100a95d0>] do_debug_exception+0x1a8/0x258
[ 112.017479] softirqs last enabled at (350): [<ffff8000100818a4>] __do_softirq+0x4bc/0x568
[ 112.025984] softirqs last disabled at (343): [<ffff8000101145a4>] irq_exit+0x144/0x150
[ 112.034129] ---[ end trace dc96030b9cf6c8a3 ]---
The problem was tracked down to a missing call to
pm_runtime_set_active() on resume in ohci-platform.
Link: https://lore.kernel.org/lkml/20200323143857.db5zphxhq4hz3hmd@e107158-lin.cambridge.arm.com/
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Qais Yousef <qais.yousef@arm.com>
CC: Tony Prisk <linux@prisktech.co.nz>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Mathias Nyman <mathias.nyman@intel.com>
CC: Oliver Neukum <oneukum@suse.de>
CC: linux-arm-kernel@lists.infradead.org
CC: linux-usb@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20200518154931.6144-1-qais.yousef@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bc138db1b96264b9c1779cf18d5a3b186aa90066 ]
The PCI Code and ID Assignment Specification changed capability ID 0
from reserved to a NULL capability in the v1.1 revision. The NULL
capability is defined to include only the 16-bit capability header,
ie. only the ID and next pointer. Unfortunately vfio-pci creates a
map of config space, where ID 0 is used to reserve the standard type
0 header. Finding an actual capability with this ID therefore results
in a bogus range marked in that map and conflicts with subsequent
capabilities. As this seems to be a dummy capability anyway and we
already support dropping capabilities, let's hide this one rather than
delving into the potentially subtle dependencies within our map.
Seen on an NVIDIA Tesla T4.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 126554465d93b10662742128918a5fc338cda4aa ]
The ps3_mm_region_destroy() and ps3_mm_vas_destroy() routines
are called very late in the shutdown via kexec's mmu_cleanup_all
routine. By the time mmu_cleanup_all runs it is too late to use
udbg_printf, and calling it will cause PS3 systems to hang.
Remove all debugging statements from ps3_mm_region_destroy() and
ps3_mm_vas_destroy() and replace any error reporting with calls
to lv1_panic.
With this change builds with 'DEBUG' defined will not cause kexec
reboots to hang, and builds with 'DEBUG' defined or not will end
in lv1_panic if an error is encountered.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/7325c4af2b4c989c19d6a26b90b1fec9c0615ddf.1589049250.git.geoff@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6f0577d1411337a0d97d545abe4a784e9e611516 ]
During different reboot cycles, USB PHY PLL may not always lock
during initialization and therefore can cause USB to be not usable.
Hence do not use internal FSM programming sequence for the USB
PHY initialization.
Fixes: 4dcddbb38b64 ("phy: sr-usb: Add Stingray USB PHY driver")
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Link: https://lore.kernel.org/r/20200513173947.10919-1-rayagonda.kokatanur@broadcom.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit deb70f7a35a22dffa55b2c3aac71bc6fb0f486ce ]
This was discovered developing qemu fwnmi sreset support. This
off-by-one bug means the last 16 bytes of the rtas area can not
be used for a 16 byte save area.
It's not a serious bug, and QEMU implementation has to retain a
workaround for old kernels, but it's good to tighten it.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Link: https://lore.kernel.org/r/20200508043408.886394-7-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a5054d8cbbe03c68dcb0957c291c942132e4101 ]
The architecture allows for machine check exceptions to cause idle
wakeups which resume at the 0x200 address which has to return via
the idle wakeup code, but the early machine check handler is run
first.
The case of a no state-loss sleep is broken because the early
handler uses non-volatile register r1 , which is needed for the wakeup
protocol, but it is not restored.
Fix this by loading r1 from the MCE exception frame before returning
to the idle wakeup code. Also update the comment which has become
stale since the idle rewrite in C.
This crash was found and fix confirmed with a machine check injection
test in qemu powernv model (which is not upstream in qemu yet).
Fixes: 10d91611f426d ("powerpc/64s: Reimplement book3s idle code in C")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200508043408.886394-2-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7c47a219b95d0e06b5ef5fcc7bad807895015eac ]
We met mulitple times of failure of staring bmc-watchdog,
due to the runtime memory allocation failure of order 4.
bmc-watchdog: page allocation failure: order:4, mode:0x40cc0(GFP_KERNEL|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0-1
CPU: 1 PID: 2571 Comm: bmc-watchdog Not tainted 5.5.0-00045-g7d6bb61d6188c #1
Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.00.01.0015.110720180833 11/07/2018
Call Trace:
dump_stack+0x66/0x8b
warn_alloc+0xfe/0x160
__alloc_pages_slowpath+0xd3e/0xd80
__alloc_pages_nodemask+0x2f0/0x340
kmalloc_order+0x18/0x70
kmalloc_order_trace+0x1d/0xb0
ipmi_create_user+0x55/0x2c0 [ipmi_msghandler]
ipmi_open+0x72/0x110 [ipmi_devintf]
chrdev_open+0xcb/0x1e0
do_dentry_open+0x1ce/0x380
path_openat+0x305/0x14f0
do_filp_open+0x9b/0x110
do_sys_open+0x1bd/0x250
do_syscall_64+0x5b/0x1f0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Using vzalloc/vfree for creating ipmi_user heals the
problem
Thanks to Stephen Rothwell for finding the vmalloc.h
inclusion issue.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7a65ee046b2238e053f6ebb610e1a082cfc49490 ]
When doing training, the DL framework (e.g. tensorflow) performs hundreds
of thousands of memory allocations and mappings. In case the driver needs
to perform hard-reset during training, the driver kills the application and
unmaps all those memory allocations. Unfortunately, because of that large
amount of mappings, the driver isn't able to do that in the current timeout
(5 seconds). Therefore, increase the timeout significantly to 30 seconds
to avoid situation where the driver resets the device with active mappings,
which sometime can cause a kernel bug.
BTW, it doesn't mean we will spend all the 30 seconds because the reset
thread checks every one second if the unmap operation is done.
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ec411e02b7a2e785a4ed9ed283207cd14f48699d ]
Kai-Heng Feng reported that it takes a long time (> 1 s) to resume
Thunderbolt-connected devices from both runtime suspend and system sleep
(s2idle).
This was because some Downstream Ports that support > 5 GT/s do not also
support Data Link Layer Link Active reporting. Per PCIe r5.0 sec 6.6.1:
With a Downstream Port that supports Link speeds greater than 5.0 GT/s,
software must wait a minimum of 100 ms after Link training completes
before sending a Configuration Request to the device immediately below
that Port. Software can determine when Link training completes by polling
the Data Link Layer Link Active bit or by setting up an associated
interrupt (see Section 6.7.3.3).
Sec 7.5.3.6 requires such Ports to support DLL Link Active reporting, but
at least the Intel JHL6240 Thunderbolt 3 Bridge [8086:15c0] and the Intel
JHL7540 Thunderbolt 3 Bridge [8086:15ea] do not.
Previously we tried to wait for Link training to complete, but since there
was no DLL Link Active reporting, all we could do was wait the worst-case
1000 ms, then another 100 ms.
Instead of using the supported speeds to determine whether to wait for Link
training, check whether the port supports DLL Link Active reporting. The
Ports in question do not, so we'll wait only the 100 ms required for Ports
that support Link speeds <= 5 GT/s.
This of course assumes these Ports always train the Link within 100 ms even
if they are operating at > 5 GT/s, which is not required by the spec.
[bhelgaas: commit log, comment]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206837
Link: https://lore.kernel.org/r/20200514133043.27429-1-mika.westerberg@linux.intel.com
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fb68ada81e65d593b51544fa43c284322107a742 ]
The Trust Panora Graphic Tablet has two interfaces. Interface zero reports pen
movement, pen pressure and pen buttons. Interface one reports tablet buttons
and tablet scroll. Both use the mouse protocol.
Without these quirks, libinput gets confused about what device it talks to.
For completeness, here is the usbhid-dump:
```
$ sudo usbhid-dump -d 145f:0212
003:013:001:DESCRIPTOR 1588949402.559961
05 0D 09 01 A1 01 85 07 A1 02 09 00 75 08 95 07
81 02 C0 C0 09 0E A1 01 85 05 09 23 A1 02 09 52
09 53 25 0A 75 08 95 02 B1 02 C0 C0 05 0C 09 36
A1 00 85 06 05 09 19 01 29 20 15 00 25 01 95 20
75 01 81 02 C0
003:013:000:DESCRIPTOR 1588949402.563942
05 01 09 02 A1 01 85 08 09 01 A1 00 05 09 19 01
29 03 15 00 25 01 95 03 75 01 81 02 95 05 81 01
05 01 09 30 09 31 09 38 09 00 15 81 25 7F 75 08
95 04 81 06 C0 C0 05 01 09 02 A1 01 85 09 09 01
A1 00 05 09 19 01 29 03 15 00 25 01 95 03 75 01
81 02 95 05 81 01 05 01 09 30 09 31 26 FF 7F 95
02 75 10 81 02 05 0D 09 30 26 FF 03 95 01 75 10
81 02 C0 C0 05 01 09 00 A1 01 85 04 A1 00 26 FF
00 09 00 75 08 95 07 B1 02 C0 C0
```
Signed-off-by: Cristian Klein <cristian.klein@elastisys.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
feedback
[ Upstream commit 10ce77e4817fef99e1166be7e6685a80c63bf77f ]
For USB sound devices using implicit feedback the endpoint used for
this feedback should be able to be opened twice, once for required
feedback and second time for audio data. This way these devices can be
put in duplex audio mode. Since this only works if the settings of the
endpoint don't change a check is included for this.
This fixes bug 207023 ("MOTU M2 regression on duplex audio") and
should also fix bug 103751 ("M-Audio Fast Track Ultra usb audio device
will not operate full-duplex")
Fixes: c249177944b6 ("ALSA: usb-audio: add implicit fb quirk for MOTU M Series")
Signed-off-by: Erwin Burema <e.burema@gmail.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207023
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=103751
Link: https://lore.kernel.org/r/2410739.SCZni40SNb@alpha-wolf
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 01dbb362f0a114fbce19c8abe4cd6f4710e934d5 ]
Warn the upper layer when n_gms is ready to receive data
again. Without this the associated virtual tty remains blocked
indefinitely.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-4-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 84d6f81c1fb58b56eba81ff0a36cf31946064b40 ]
For at least some modems like the TELIT LE910, skipping SOF makes
transfers blocking indefinitely after a short amount of data
transferred.
Given the small improvement provided by skipping the SOF (just one
byte on about 100 bytes), it seems better to completely remove this
"feature" than make it optional.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7ffa8b7dc11752827329e4e84a574ea6aaf24716 ]
Aneesh increased the size of struct pt_regs by 16 bytes and started
seeing this WARN_ON:
smp: Bringing up secondary CPUs ...
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at arch/powerpc/kernel/process.c:455 giveup_all+0xb4/0x110
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.7.0-rc2-gcc-8.2.0-1.g8f6a41f-default+ #318
NIP: c00000000001a2b4 LR: c00000000001a29c CTR: c0000000031d0000
REGS: c0000000026d3980 TRAP: 0700 Not tainted (5.7.0-rc2-gcc-8.2.0-1.g8f6a41f-default+)
MSR: 800000000282b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 48048224 XER: 00000000
CFAR: c000000000019cc8 IRQMASK: 1
GPR00: c00000000001a264 c0000000026d3c20 c0000000026d7200 800000000280b033
GPR04: 0000000000000001 0000000000000000 0000000000000077 30206d7372203164
GPR08: 0000000000002000 0000000002002000 800000000280b033 3230303030303030
GPR12: 0000000000008800 c0000000031d0000 0000000000800050 0000000002000066
GPR16: 000000000309a1a0 000000000309a4b0 000000000309a2d8 000000000309a890
GPR20: 00000000030d0098 c00000000264da40 00000000fd620000 c0000000ff798080
GPR24: c00000000264edf0 c0000001007469f0 00000000fd620000 c0000000020e5e90
GPR28: c00000000264edf0 c00000000264d200 000000001db60000 c00000000264d200
NIP [c00000000001a2b4] giveup_all+0xb4/0x110
LR [c00000000001a29c] giveup_all+0x9c/0x110
Call Trace:
[c0000000026d3c20] [c00000000001a264] giveup_all+0x64/0x110 (unreliable)
[c0000000026d3c90] [c00000000001ae34] __switch_to+0x104/0x480
[c0000000026d3cf0] [c000000000e0b8a0] __schedule+0x320/0x970
[c0000000026d3dd0] [c000000000e0c518] schedule_idle+0x38/0x70
[c0000000026d3df0] [c00000000019c7c8] do_idle+0x248/0x3f0
[c0000000026d3e70] [c00000000019cbb8] cpu_startup_entry+0x38/0x40
[c0000000026d3ea0] [c000000000011bb0] rest_init+0xe0/0xf8
[c0000000026d3ed0] [c000000002004820] start_kernel+0x990/0x9e0
[c0000000026d3f90] [c00000000000c49c] start_here_common+0x1c/0x400
Which was unexpected. The warning is checking the thread.regs->msr
value of the task we are switching from:
usermsr = tsk->thread.regs->msr;
...
WARN_ON((usermsr & MSR_VSX) && !((usermsr & MSR_FP) && (usermsr & MSR_VEC)));
ie. if MSR_VSX is set then both of MSR_FP and MSR_VEC are also set.
Dumping tsk->thread.regs->msr we see that it's: 0x1db60000
Which is not a normal looking MSR, in fact the only valid bit is
MSR_VSX, all the other bits are reserved in the current definition of
the MSR.
We can see from the oops that it was swapper/0 that we were switching
from when we hit the warning, ie. init_task. So its thread.regs points
to the base (high addresses) in init_stack.
Dumping the content of init_task->thread.regs, with the members of
pt_regs annotated (the 16 bytes larger version), we see:
0000000000000000 c000000002780080 gpr[0] gpr[1]
0000000000000000 c000000002666008 gpr[2] gpr[3]
c0000000026d3ed0 0000000000000078 gpr[4] gpr[5]
c000000000011b68 c000000002780080 gpr[6] gpr[7]
0000000000000000 0000000000000000 gpr[8] gpr[9]
c0000000026d3f90 0000800000002200 gpr[10] gpr[11]
c000000002004820 c0000000026d7200 gpr[12] gpr[13]
000000001db60000 c0000000010aabe8 gpr[14] gpr[15]
c0000000010aabe8 c0000000010aabe8 gpr[16] gpr[17]
c00000000294d598 0000000000000000 gpr[18] gpr[19]
0000000000000000 0000000000001ff8 gpr[20] gpr[21]
0000000000000000 c00000000206d608 gpr[22] gpr[23]
c00000000278e0cc 0000000000000000 gpr[24] gpr[25]
000000002fff0000 c000000000000000 gpr[26] gpr[27]
0000000002000000 0000000000000028 gpr[28] gpr[29]
000000001db60000 0000000004750000 gpr[30] gpr[31]
0000000002000000 000000001db60000 nip msr
0000000000000000 0000000000000000 orig_r3 ctr
c00000000000c49c 0000000000000000 link xer
0000000000000000 0000000000000000 ccr softe
0000000000000000 0000000000000000 trap dar
0000000000000000 0000000000000000 dsisr result
0000000000000000 0000000000000000 ppr kuap
0000000000000000 0000000000000000 pad[2] pad[3]
This looks suspiciously like stack frames, not a pt_regs. If we look
closely we can see return addresses from the stack trace above,
c000000002004820 (start_kernel) and c00000000000c49c (start_here_common).
init_task->thread.regs is setup at build time in processor.h:
#define INIT_THREAD { \
.ksp = INIT_SP, \
.regs = (struct pt_regs *)INIT_SP - 1, /* XXX bogus, I think */ \
The early boot code where we setup the initial stack is:
LOAD_REG_ADDR(r3,init_thread_union)
/* set up a stack pointer */
LOAD_REG_IMMEDIATE(r1,THREAD_SIZE)
add r1,r3,r1
li r0,0
stdu r0,-STACK_FRAME_OVERHEAD(r1)
Which creates a stack frame of size 112 bytes (STACK_FRAME_OVERHEAD).
Which is far too small to contain a pt_regs.
So the result is init_task->thread.regs is pointing at some stack
frames on the init stack, not at a pt_regs.
We have gotten away with this for so long because with pt_regs at its
current size the MSR happens to point into the first frame, at a
location that is not written to by the early asm. With the 16 byte
expansion the MSR falls into the second frame, which is used by the
compiler, and collides with a saved register that tends to be
non-zero.
As far as I can see this has been wrong since the original merge of
64-bit ppc support, back in 2002.
Conceptually swapper should have no regs, it never entered from
userspace, and in fact that's what we do on 32-bit. It's also
presumably what the "bogus" comment is referring to.
So I think the right fix is to just not-initialise regs at all. I'm
slightly worried this will break some code that isn't prepared for a
NULL regs, but we'll have to see.
Remove the comment in head_64.S which refers to us setting up the
regs (even though we never did), and is otherwise not really accurate
any more.
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200428123130.73078-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1b54ae8327a4d630111c8d88ba7906483ec6010b ]
If device_register() has an error, we should bail out of
pci_register_host_bridge() rather than continuing on.
Fixes: 37d6a0a6f470 ("PCI: Add pci_register_host_bridge() interface")
Link: https://lore.kernel.org/r/20200513223859.11295-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c7c1cbbc9217ebb5601b88d138d4a5358548de9d ]
The parent_names is never released for a component clock definition,
causing some memory leak. Fix by releasing it once it is no longer
needed.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lkml.kernel.org/r/20200429131341.4697-2-t-kristo@ti.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b919e077cccfbb77beb98809568b2fb0b4d113ec ]
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 7d9e6f5aebe8 ("usb: host: ohci-sm501: init genalloc for local memory")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200506135625.106910-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fe204591cc9480347af7d2d6029b24a62e449486 ]
Building a kernel with clang sometimes fails with an objtool error in dlm:
fs/dlm/lock.o: warning: objtool: revert_lock_pc()+0xbd: can't find jump dest instruction at .text+0xd7fc
The problem is that BUG() never returns and the compiler knows
that anything after it is unreachable, however the panic still
emits some code that does not get fully eliminated.
Having both BUG() and panic() is really pointless as the BUG()
kills the current process and the subsequent panic() never hits.
In most cases, we probably don't really want either and should
replace the DLM_ASSERT() statements with WARN_ON(), as has
been done for some of them.
Remove the BUG() here so the user at least sees the panic message
and we can reliably build randconfig kernels.
Fixes: e7fd41792fc0 ("[DLM] The core of the DLM for GFS2/CLVM")
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: clang-built-linux@googlegroups.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
