| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 4d2b496f19f3c2cfaca1e8fa0710688b5ff3811d upstream.
map_storep was not being vfree()'d in the module_exit call.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1e793f6fc0db920400574211c48f9157a37e3945 upstream.
Commit 02b01e010afe ("megaraid_sas: return sync cache call with
success") modified the driver to successfully complete SYNCHRONIZE_CACHE
commands without passing them to the controller. Disk drive caches are
only explicitly managed by controller firmware when operating in RAID
mode. So this commit effectively disabled writeback cache flushing for
any drives used in JBOD mode, leading to data integrity failures.
[mkp: clarified patch description]
Fixes: 02b01e010afeeb49328d35650d70721d2ca3fd59
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea720935cf6686f72def9d322298bf7e9bd53377 upstream.
In mac80211, multicast A-MSDUs are accepted in many cases that
they shouldn't be accepted in:
* drop A-MSDUs with a multicast A1 (RA), as required by the
spec in 9.11 (802.11-2012 version)
* drop A-MSDUs with a 4-addr header, since the fourth address
can't actually be useful for them; unless 4-address frame
format is actually requested, even though the fourth address
is still not useful in this case, but ignored
Accepting the first case, in particular, is very problematic
since it allows anyone else with possession of a GTK to send
unicast frames encapsulated in a multicast A-MSDU, even when
the AP has client isolation enabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e9300a4b7bbae83af1f7703938c94cf6dc6d308f upstream.
RFC 2734 defines the datagram_size field in fragment encapsulation
headers thus:
datagram_size: The encoded size of the entire IP datagram. The
value of datagram_size [...] SHALL be one less than the value of
Total Length in the datagram's IP header (see STD 5, RFC 791).
Accordingly, the eth1394 driver of Linux 2.6.36 and older set and got
this field with a -/+1 offset:
ether1394_tx() /* transmit */
ether1394_encapsulate_prep()
hdr->ff.dg_size = dg_size - 1;
ether1394_data_handler() /* receive */
if (hdr->common.lf == ETH1394_HDR_LF_FF)
dg_size = hdr->ff.dg_size + 1;
else
dg_size = hdr->sf.dg_size + 1;
Likewise, I observe OS X 10.4 and Windows XP Pro SP3 to transmit 1500
byte sized datagrams in fragments with datagram_size=1499 if link
fragmentation is required.
Only firewire-net sets and gets datagram_size without this offset. The
result is lacking interoperability of firewire-net with OS X, Windows
XP, and presumably Linux' eth1394. (I did not test with the latter.)
For example, FTP data transfers to a Linux firewire-net box with max_rec
smaller than the 1500 bytes MTU
- from OS X fail entirely,
- from Win XP start out with a bunch of fragmented datagrams which
time out, then continue with unfragmented datagrams because Win XP
temporarily reduces the MTU to 576 bytes.
So let's fix firewire-net's datagram_size accessors.
Note that firewire-net thereby loses interoperability with unpatched
firewire-net, but only if link fragmentation is employed. (This happens
with large broadcast datagrams, and with large datagrams on several
FireWire CardBus cards with smaller max_rec than equivalent PCI cards,
and it can be worked around by setting a small enough MTU.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 667121ace9dbafb368618dbabcf07901c962ddac upstream.
The IP-over-1394 driver firewire-net lacked input validation when
handling incoming fragmented datagrams. A maliciously formed fragment
with a respectively large datagram_offset would cause a memcpy past the
datagram buffer.
So, drop any packets carrying a fragment with offset + length larger
than datagram_size.
In addition, ensure that
- GASP header, unfragmented encapsulation header, or fragment
encapsulation header actually exists before we access it,
- the encapsulated datagram or fragment is of nonzero size.
Reported-by: Eyal Itkin <eyal.itkin@gmail.com>
Reviewed-by: Eyal Itkin <eyal.itkin@gmail.com>
Fixes: CVE 2016-8633
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit da25311c7ca8b0254a686fc0d597075b9aa3b683 upstream.
The Schenker XMG C504 is a rebranded Gigabyte P35 v2 laptop.
Therefore it also needs a keyboard reset to detect the Elantech touchpad.
Otherwise the touchpad appears to be dead.
With this patch the touchpad is detected:
$ dmesg | grep -E "(i8042|Elantech|elantech)"
[ 2.675399] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.680372] i8042: Attempting to reset device connected to KBD port
[ 2.789037] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.791586] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.813840] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 3.811431] psmouse serio1: elantech: assuming hardware version 4 (with firmware version 0x361f0e)
[ 3.825424] psmouse serio1: elantech: Synaptics capabilities query result 0x00, 0x15, 0x0f.
[ 3.839424] psmouse serio1: elantech: Elan sample query result 03, 58, 74
[ 3.911349] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input6
Signed-off-by: Patrick Scheuring <patrick.scheuring.dev@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dcb2ff56417362c31f6b430c3c531a84581e8721 upstream.
If a default leg has failed, any read will cause a new operational
default leg to be selected and the read is resubmitted. But until now
the read will return failure even though it was successful due to
resubmission. The reason for this is bio->bi_error was not being
cleared before resubmitting the bio.
Fix by clearing bio->bi_error before resubmission.
Fixes: 4246a0b63bd8 ("block: add a bi_error field to struct bio")
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34563769e438d2881f62cf4d9badc4e589ac0ec0 upstream.
Commit c6017e793b93 ("virtio: console: add locks around buffer removal
in port unplug path") added locking around the freeing of buffers in the
vq. However, when free_buf() is called with can_sleep = true and rproc
is enabled, it calls dma_free_coherent() directly, requiring interrupts
to be enabled. Currently a WARNING is triggered due to the spin locking
around free_buf, with a call stack like this:
WARNING: CPU: 3 PID: 121 at ./include/linux/dma-mapping.h:433
free_buf+0x1a8/0x288
Call Trace:
[<8040c538>] show_stack+0x74/0xc0
[<80757240>] dump_stack+0xd0/0x110
[<80430d98>] __warn+0xfc/0x130
[<80430ee0>] warn_slowpath_null+0x2c/0x3c
[<807e7c6c>] free_buf+0x1a8/0x288
[<807ea590>] remove_port_data+0x50/0xac
[<807ea6a0>] unplug_port+0xb4/0x1bc
[<807ea858>] virtcons_remove+0xb0/0xfc
[<807b6734>] virtio_dev_remove+0x58/0xc0
[<807f918c>] __device_release_driver+0xac/0x134
[<807f924c>] device_release_driver+0x38/0x50
[<807f7edc>] bus_remove_device+0xfc/0x130
[<807f4b74>] device_del+0x17c/0x21c
[<807f4c38>] device_unregister+0x24/0x38
[<807b6b50>] unregister_virtio_device+0x28/0x44
Fix this by restructuring the loops to allow the locks to only be taken
where it is necessary to protect the vqs, and release it while the
buffer is being freed.
Fixes: c6017e793b93 ("virtio: console: add locks around buffer removal in port unplug path")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0ea1e4a6d9b62cf29e210d2b4ba9fd43917522e3 upstream.
According to the spec, if the VIRTIO_RING_F_EVENT_IDX feature bit is
negotiated the driver MUST set flags to 0. Not dirtying the available
ring in virtqueue_disable_cb also has a minor positive performance
impact, improving L1 dcache load missed by ~0.5% in vring_bench.
Writes to the used event field (vring_used_event) are still unconditional.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6ed518328d0189e0fdf1bb7c73290d546143ea66 upstream.
We have one critical section in the syscall entry path in which we switch from
the userspace stack to kernel stack. In the event of an external interrupt, the
interrupt code distinguishes between those two states by analyzing the value of
sr7. If sr7 is zero, it uses the kernel stack. Therefore it's important, that
the value of sr7 is in sync with the currently enabled stack.
This patch now disables interrupts while executing the critical section. This
prevents the interrupt handler to possibly see an inconsistent state which in
the worst case can lead to crashes.
Interestingly, in the syscall exit path interrupts were already disabled in the
critical section which switches back to the userspace stack.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 641089c1549d8d3df0b047b5de7e9a111362cdce upstream.
Make sure the copied up file hits the disk before renaming to the final
destination. If this is not done then the copy-up may corrupt the data in
the file in case of a crash.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ede5f3e7b54a4347be4d8525269eae50902bd7cd upstream.
The ERET instruction to return from exception is used for returning from
exception level (Status.EXL) and error level (Status.ERL). If both bits
are set however we should be returning from ERL first, as ERL can
interrupt EXL, for example when an NMI is taken. KVM however checks EXL
first.
Fix the order of the checks to match the pseudocode in the instruction
set manual.
Fixes: e685c689f3a8 ("KVM/MIPS32: Privileged instruction/target branch emulation.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd768e146624cbec7122ed15dead8daa137d909d upstream.
vcpu->arch.wbinvd_dirty_mask may still be used after freeing it,
corrupting memory. For example, the following call trace may set a bit
in an already freed cpu mask:
kvm_arch_vcpu_load
vcpu_load
vmx_free_vcpu_nested
vmx_free_vcpu
kvm_arch_vcpu_free
Fix this by deferring freeing of wbinvd_dirty_mask.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d09960b0032174eb493c4c13be5b9c9ef36dc9a7 upstream.
dm_old_request_fn() has paths that access md->io_barrier. The party
destroying io_barrier should ensure that no future execution of
dm_old_request_fn() is possible. Move io_barrier destruction to below
blk_cleanup_queue() to ensure this and avoid a NULL pointer crash during
request-based DM device shutdown.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit de24e0a108bc48062e1c7acaa97014bce32a919f upstream.
The current tiocmget implementation would fail to report errors up the
stack and instead leaked a few bits from the stack as a mask of
modem-status flags.
Fixes: 39a66b8d22a3 ("[PATCH] USB: CP2101 Add support for flow control")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 32b2921e6a7461fe63b71217067a6cf4bddb132f upstream.
Size of kmalloc() in vc_do_resize() is controlled by user.
Too large kmalloc() size triggers WARNING message on console.
Put a reasonable upper bound on terminal size to prevent WARNINGs.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
CC: David Rientjes <rientjes@google.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: linux-kernel@vger.kernel.org
Cc: syzkaller@googlegroups.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4c39135aa412d2f1381e43802523da110ca7855c upstream.
xHC in Wildcatpoint-LP PCH is similar to LynxPoint-LP and need the
same quirks to prevent machines from spurious restart while
shutting them down.
Reported-by: Hasan Mahmood <hasan.mahm@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 407a3aee6ee2d2cb46d9ba3fc380bc29f35d020c upstream.
The host keeps sending heartbeat packets independent of the
guest responding to them. Even though we respond to the heartbeat messages at
interrupt level, we can have situations where there maybe multiple heartbeat
messages pending that have not been responded to. For instance this occurs when the
VM is paused and the host continues to send the heartbeat messages.
Address this issue by draining and responding to all
the heartbeat messages that maybe pending.
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 009e39ae44f4191188aeb6dfbf661b771dbbe515 upstream.
When resizing a vt its selection may exceed the new size, resulting in
an invalid memory access [1]. Clear the selection before resizing.
[1] http://lkml.kernel.org/r/CACT4Y+acDTwy4umEvf5ROBGiRJNrxHN4Cn5szCXE5Jw-d1B=Xw@mail.gmail.com
Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Not upstream as it is not needed there.
So a patch something like this might be a safe way to fix the
potential infoleak in older kernels.
THIS IS UNTESTED. It's a very obvious patch, though, so if it compiles
it probably works. It just initializes the output variable with 0 in
the inline asm description, instead of doing it in the exception
handler.
It will generate slightly worse code (a few unnecessary ALU
operations), but it doesn't have any interactions with the exception
handler implementation.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a7a7aeefbca2982586ba2c9fd7739b96416a6d1d upstream.
When interrupting an application which was allocating DMAable
memory, it was possible, that the DMA memory was deallocated
twice, leading to the error symptoms below.
Thanks to Gerald, who analyzed the problem and provided this
patch.
I agree with his analysis of the problem: ddcb_cmd_fixups() ->
genwqe_alloc_sync_sgl() (fails in f/lpage, but sgl->sgl != NULL
and f/lpage maybe also != NULL) -> ddcb_cmd_cleanup() ->
genwqe_free_sync_sgl() (double free, because sgl->sgl != NULL and
f/lpage maybe also != NULL)
In this scenario we would have exactly the kind of double free that
would explain the WARNING / Bad page state, and as expected it is
caused by broken error handling (cleanup).
Using the Ubuntu git source, tag Ubuntu-4.4.0-33.52, he was able to reproduce
the "Bad page state" issue, and with the patch on top he could not reproduce
it any more.
------------[ cut here ]------------
WARNING: at /build/linux-o03cxz/linux-4.4.0/arch/s390/include/asm/pci_dma.h:141
Modules linked in: qeth_l2 ghash_s390 prng aes_s390 des_s390 des_generic sha512_s390 sha256_s390 sha1_s390 sha_common genwqe_card qeth crc_itu_t qdio ccwgroup vmur dm_multipath dasd_eckd_mod dasd_mod
CPU: 2 PID: 3293 Comm: genwqe_gunzip Not tainted 4.4.0-33-generic #52-Ubuntu
task: 0000000032c7e270 ti: 00000000324e4000 task.ti: 00000000324e4000
Krnl PSW : 0404c00180000000 0000000000156346 (dma_update_cpu_trans+0x9e/0xa8)
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:0 PM:0 EA:3
Krnl GPRS: 00000000324e7bcd 0000000000c3c34a 0000000027628298 000000003215b400
0000000000000400 0000000000001fff 0000000000000400 0000000116853000
07000000324e7b1e 0000000000000001 0000000000000001 0000000000000001
0000000000001000 0000000116854000 0000000000156402 00000000324e7a38
Krnl Code: 000000000015633a: 95001000 cli 0(%r1),0
000000000015633e: a774ffc3 brc 7,1562c4
#0000000000156342: a7f40001 brc 15,156344
>0000000000156346: 92011000 mvi 0(%r1),1
000000000015634a: a7f4ffbd brc 15,1562c4
000000000015634e: 0707 bcr 0,%r7
0000000000156350: c00400000000 brcl 0,156350
0000000000156356: eb7ff0500024 stmg %r7,%r15,80(%r15)
Call Trace:
([<00000000001563e0>] dma_update_trans+0x90/0x228)
[<00000000001565dc>] s390_dma_unmap_pages+0x64/0x160
[<00000000001567c2>] s390_dma_free+0x62/0x98
[<000003ff801310ce>] __genwqe_free_consistent+0x56/0x70 [genwqe_card]
[<000003ff801316d0>] genwqe_free_sync_sgl+0xf8/0x160 [genwqe_card]
[<000003ff8012bd6e>] ddcb_cmd_cleanup+0x86/0xa8 [genwqe_card]
[<000003ff8012c1c0>] do_execute_ddcb+0x110/0x348 [genwqe_card]
[<000003ff8012c914>] genwqe_ioctl+0x51c/0xc20 [genwqe_card]
[<000000000032513a>] do_vfs_ioctl+0x3b2/0x518
[<0000000000325344>] SyS_ioctl+0xa4/0xb8
[<00000000007b86c6>] system_call+0xd6/0x264
[<000003ff9e8e520a>] 0x3ff9e8e520a
Last Breaking-Event-Address:
[<0000000000156342>] dma_update_cpu_trans+0x9a/0xa8
---[ end trace 35996336235145c8 ]---
BUG: Bad page state in process jbd2/dasdb1-8 pfn:3215b
page:000003d100c856c0 count:-1 mapcount:0 mapping: (null) index:0x0
flags: 0x3fffc0000000000()
page dumped because: nonzero _count
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Frank Haverkamp <haver@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ed6d6f8f42d7302f6f9b6245f34927ec20d26c12 upstream.
Increase ohci watchout delay to 275 ms. Previous delay was 250 ms
with 20 ms of slack, after removing slack time some ohci controllers don't
respond in time. Logs from systems with controllers that have the
issue would show "HcDoneHead not written back; disabled"
Signed-off-by: Bryan Paluch <bryanpaluch@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d3b016a6f5a0fa610dfd02b05654c08fa4ae514 upstream.
USB2 host inititated resume, and system suspend bus resume
need to use the same USB_RESUME_TIMEOUT as elsewhere.
This resolves a device disconnect issue at system resume seen
on Intel Braswell and Apollolake, but is in no way limited to
those platforms.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca006f785fbfd7a5c901900bd3fe2b26e946a1ee upstream.
This adds support to ftdi_sio for the Infineon TriBoard TC2X7
engineering board for first-generation Aurix SoCs with Tricore CPUs.
Mere addition of the device IDs does the job.
Signed-off-by: Stefan Tauner <stefan.tauner@technikum-wien.at>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 126d26f66d9890a69158812a6caa248c05359daa upstream.
Make sure we have at least one port before attempting to register a
console.
Currently, at least one driver binds to a "dummy" interface and requests
zero ports for it. Should such an interface also lack endpoints, we get
a NULL-deref during probe.
Fixes: e5b1e2062e05 ("USB: serial: make minor allocation dynamic")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6c83f77278f17a7679001027e9231291c20f0d8a upstream.
If we don't guarantee that we will always get an
interrupt at least when we're queueing our very last
request, we could fall into situation where we queue
every request with 'no_interrupt' set. This will
cause the link to get stuck.
The behavior above has been triggered with g_ether
and dwc3.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 43605e293eb13c07acb546c14f407a271837af17 upstream.
SEC registers are not accessible when the TXE device is in low power
state, hence the SEC interrupt cannot be processed if device is not
awake.
In some rare cases entrance to low power state (aliveness off) and input
ready bits can be signaled at the same time, resulting in communication
stall as input ready won't be signaled again after waking up. To resolve
this IPC_HHIER_SEC bit in HHISR_REG should not be cleaned if the
interrupt is not processed.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a00052a296e54205cf238c75bd98d17d5d02a6db upstream.
Commit c83ed4c9dbb35 ("ubifs: Abort readdir upon error") broke
overlayfs support because the fix exposed an internal error
code to VFS.
Reported-by: Peter Rosin <peda@axentia.se>
Tested-by: Peter Rosin <peda@axentia.se>
Reported-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Tested-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Fixes: c83ed4c9dbb35 ("ubifs: Abort readdir upon error")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c83ed4c9dbb358b9e7707486e167e940d48bfeed upstream.
If UBIFS is facing an error while walking a directory, it reports this
error and ubifs_readdir() returns the error code. But the VFS readdir
logic does not make the getdents system call fail in all cases. When the
readdir cursor indicates that more entries are present, the system call
will just return and the libc wrapper will try again since it also
knows that more entries are present.
This causes the libc wrapper to busy loop for ever when a directory is
corrupted on UBIFS.
A common approach do deal with corrupted directory entries is
skipping them by setting the cursor to the next entry. On UBIFS this
approach is not possible since we cannot compute the next directory
entry cursor position without reading the current entry. So all we can
do is setting the cursor to the "no more entries" position and make
getdents exit.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 570dd45042a7c8a7aba1ee029c5dd0f5ccf41b9b upstream.
btrfs_remove_all_log_ctxs takes a shortcut where it avoids walking the
list because it knows all of the waiters are patiently waiting for the
commit to finish.
But, there's a small race where btrfs_sync_log can remove itself from
the list if it finds a log commit is already done. Also, it uses
list_del_init() to remove itself from the list, but there's no way to
know if btrfs_remove_all_log_ctxs has already run, so we don't know for
sure if it is safe to call list_del_init().
This gets rid of all the shortcuts for btrfs_remove_all_log_ctxs(), and
just calls it with the proper locking.
This is part two of the corruption fixed by cbd60aa7cd1. I should have
done this in the first place, but convinced myself the optimizations were
safe. A 12 hour run of dbench 2048 will eventually trigger a list debug
WARN_ON for the list_del_init() in btrfs_sync_log().
Fixes: d1433debe7f4346cf9fc0dafc71c3137d2a97bc4
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
struct
commit 4afb604e2d14d429ac9e1fd84b952602853b2df5 upstream.
Prevents leaking pointers between processes
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Martijn Coenen <maco@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a3ffab93fe52530602fe47cd74802cffdb19c05 upstream.
Prevent using a binder_ref with only weak references where a strong
reference is required.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Martijn Coenen <maco@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6aecd8715802d23dc6a0859b50c62d2b0a99de3a upstream.
They uses the codec ALC255, and have the different pin cfg definition
from the ones in the existing pin quirk table. Now adding them into
the table to fix the problem.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f771d5bb71d4df9573d12386400540516672208b upstream.
We have a new Dell laptop model which uses ALC295, the pin definition
is different from the existing ones in the pin quirk table, to fix the
headset mic detection and mic mute led's problem, we need to add the
new pin defintion into the pin quirk table.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3ab7511eafdd5c4f40d2832f09554478dfbea170 upstream.
Commit 49d9e77e72cf ("ALSA: hda - Fix system panic when DMA > 40 bits
for Nvidia audio controllers") simply disabled any DMA exceeding 32
bits for NVidia devices, even though they are capable of performing
DMA up to 40 bits. On some architectures (such as arm64), system memory
is not guaranteed to be 32-bit addressable by PCI devices, and so this
change prevents NVidia devices from working on platforms such as AMD
Seattle.
Since the original commit already mentioned that up to 40 bits of DMA
is supported, and given that the code has been updated in the meantime
to support a 40 bit DMA mask on other devices, revert commit 49d9e77e72cf
and explicitly set the DMA mask to 40 bits for NVidia devices.
Fixes: 49d9e77e72cf ('ALSA: hda - Fix system panic when DMA > 40 bits...')
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d9a180895ee8c301df7f9447429009795c56c21 upstream.
AZX_DCAPS_RIRB_DELAY is dedicated only for Nvidia and its purpose is
just to set a flag in bus. So it's better to be set in the toplevel
driver, either hda_intel.c or hda_tegra.c, instead of the common
hda_controller.c. This also allows us to strip this flag from dcaps,
so save one more bit there.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ef85f299c74e6c5dd98ec0230183be33f4c2813d upstream.
AZX_DCAPS_RIRB_PRE_DELAY is always tied with AZX_DCAPS_CTX_WORKAROUND,
which is Creative's XFi specific. So, we can replace it and reduce
one more bit free for DCAPS.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bdc3478f90cd4d2928197f36629d5cf93b64dbe9 upstream.
The stk1160 chip needs QUIRK_AUDIO_ALIGN_TRANSFER. This patch resolves
the issue reported on the mailing list
(http://marc.info/?l=linux-sound&m=139223599126215&w=2) and also fixes
bug 180071 (https://bugzilla.kernel.org/show_bug.cgi?id=180071).
Signed-off-by: Marcel Hasler <mahasler@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03dab869b7b239c4e013ec82aea22e181e441cfc upstream.
This fixes CVE-2016-7042.
Fix a short sprintf buffer in proc_keys_show(). If the gcc stack protector
is turned on, this can cause a panic due to stack corruption.
The problem is that xbuf[] is not big enough to hold a 64-bit timeout
rendered as weeks:
(gdb) p 0xffffffffffffffffULL/(60*60*24*7)
$2 = 30500568904943
That's 14 chars plus NUL, not 11 chars plus NUL.
Expand the buffer to 16 chars.
I think the unpatched code apparently works if the stack-protector is not
enabled because on a 32-bit machine the buffer won't be overflowed and on a
64-bit machine there's a 64-bit aligned pointer at one side and an int that
isn't checked again on the other side.
The panic incurred looks something like:
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ffffffff81352ebe
CPU: 0 PID: 1692 Comm: reproducer Not tainted 4.7.2-201.fc24.x86_64 #1
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
0000000000000086 00000000fbbd2679 ffff8800a044bc00 ffffffff813d941f
ffffffff81a28d58 ffff8800a044bc98 ffff8800a044bc88 ffffffff811b2cb6
ffff880000000010 ffff8800a044bc98 ffff8800a044bc30 00000000fbbd2679
Call Trace:
[<ffffffff813d941f>] dump_stack+0x63/0x84
[<ffffffff811b2cb6>] panic+0xde/0x22a
[<ffffffff81352ebe>] ? proc_keys_show+0x3ce/0x3d0
[<ffffffff8109f7f9>] __stack_chk_fail+0x19/0x30
[<ffffffff81352ebe>] proc_keys_show+0x3ce/0x3d0
[<ffffffff81350410>] ? key_validate+0x50/0x50
[<ffffffff8134db30>] ? key_default_cmp+0x20/0x20
[<ffffffff8126b31c>] seq_read+0x2cc/0x390
[<ffffffff812b6b12>] proc_reg_read+0x42/0x70
[<ffffffff81244fc7>] __vfs_read+0x37/0x150
[<ffffffff81357020>] ? security_file_permission+0xa0/0xc0
[<ffffffff81246156>] vfs_read+0x96/0x130
[<ffffffff81247635>] SyS_read+0x55/0xc0
[<ffffffff817eb872>] entry_SYSCALL_64_fastpath+0x1a/0xa4
Reported-by: Ondrej Kozina <okozina@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Ondrej Kozina <okozina@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 89a2848381b5fcd9c4d9c0cd97680e3b28730e31 upstream.
On 4.0, we saw a stack corruption from a page fault entering direct
memory cgroup reclaim, calling into btrfs_releasepage(), which then
tried to allocate an extent and recursed back into a kmem charge ad
nauseam:
[...]
btrfs_releasepage+0x2c/0x30
try_to_release_page+0x32/0x50
shrink_page_list+0x6da/0x7a0
shrink_inactive_list+0x1e5/0x510
shrink_lruvec+0x605/0x7f0
shrink_zone+0xee/0x320
do_try_to_free_pages+0x174/0x440
try_to_free_mem_cgroup_pages+0xa7/0x130
try_charge+0x17b/0x830
memcg_charge_kmem+0x40/0x80
new_slab+0x2d9/0x5a0
__slab_alloc+0x2fd/0x44f
kmem_cache_alloc+0x193/0x1e0
alloc_extent_state+0x21/0xc0
__clear_extent_bit+0x2b5/0x400
try_release_extent_mapping+0x1a3/0x220
__btrfs_releasepage+0x31/0x70
btrfs_releasepage+0x2c/0x30
try_to_release_page+0x32/0x50
shrink_page_list+0x6da/0x7a0
shrink_inactive_list+0x1e5/0x510
shrink_lruvec+0x605/0x7f0
shrink_zone+0xee/0x320
do_try_to_free_pages+0x174/0x440
try_to_free_mem_cgroup_pages+0xa7/0x130
try_charge+0x17b/0x830
mem_cgroup_try_charge+0x65/0x1c0
handle_mm_fault+0x117f/0x1510
__do_page_fault+0x177/0x420
do_page_fault+0xc/0x10
page_fault+0x22/0x30
On later kernels, kmem charging is opt-in rather than opt-out, and that
particular kmem allocation in btrfs_releasepage() is no longer being
charged and won't recurse and overrun the stack anymore.
But it's not impossible for an accounted allocation to happen from the
memcg direct reclaim context, and we needed to reproduce this crash many
times before we even got a useful stack trace out of it.
Like other direct reclaimers, mark tasks in memcg reclaim PF_MEMALLOC to
avoid recursing into any other form of direct reclaim. Then let
recursive charges from PF_MEMALLOC contexts bypass the cgroup limit.
Link: http://lkml.kernel.org/r/20161025141050.GA13019@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1bc11d70b5db7c6bb1414b283d7f09b1fe1ac0d0 upstream.
As described in https://bugzilla.kernel.org/show_bug.cgi?id=177821:
After some analysis it seems to be that the problem is in alloc_super().
In case list_lru_init_memcg() fails it goes into destroy_super(), which
calls list_lru_destroy().
And in list_lru_init() we see that in case memcg_init_list_lru() fails,
lru->node is freed, but not set NULL, which then leads list_lru_destroy()
to believe it is initialized and call memcg_destroy_list_lru().
memcg_destroy_list_lru() in turn can access lru->node[i].memcg_lrus,
which is NULL.
[akpm@linux-foundation.org: add comment]
Signed-off-by: Alexander Polakov <apolyakov@beget.ru>
Acked-by: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 58d789678546d46d7bbd809dd7dab417c0f23655 upstream.
The function xfs_calc_dquots_per_chunk takes a parameter in units
of basic blocks. The kernel seems to get the units wrong, but
userspace got 'fixed' by commenting out the unnecessary conversion.
Fix both.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 21753583056d48a5fad964d6f272e28168426845 upstream.
Back in commit f56141e3e2d9 ("all arches, signal: move restart_block to
struct task_struct"), all architectures and core code were changed to
use task_struct::restart_block. However, when h8300 support was
subsequently restored in v4.2, it was not updated to account for this,
and maintains thread_info::restart_block, which is not kept in sync.
This patch drops the redundant restart_block from thread_info, and moves
h8300 to the common one in task_struct, ensuring that syscall restarting
always works as expected.
Fixes: f56141e3e2d9 ("all arches, signal: move restart_block to struct task_struct")
Link: http://lkml.kernel.org/r/1476714934-11635-1-git-send-email-mark.rutland@arm.com
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 36e3fa6a38e135e9478a2f75dec9bf6ff1e6480e upstream.
The i2c adapter is only relevant for some peer device types, so
let's clear the pdt if it's still the same as the old_pdt when we
tear down the i2c adapter.
I don't really like this design pattern of updating port->whatever
before doing the accompanying changes and passing around old_whatever
to figure stuff out. Would make much more sense to me to the pass the
new value around and only update the port->whatever when things are
consistent. But let's try to work with what we have right now.
Quoting a follow-up from Ville:
"And naturally I forgot to amend the commit message w.r.t. this guy
[the change in drm_dp_destroy_port]. We don't really need to do this
here, but I figured I'd try to be a bit more consistent by having it,
just to avoid accidental mistakes if/when someone changes this stuff
again later."
v2: Clear port->pdt in the caller, if needed (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Carlos Santa <carlos.santa@intel.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Tested-by: Carlos Santa <carlos.santa@intel.com>
Tested-by: Kirill A. Shutemov <kirill@shutemov.name>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97666
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1477488633-16544-1-git-send-email-ville.syrjala@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 147b36d5b70c083cc76770c47d60b347e8eaf231 upstream.
Race condition between registering an I2C device driver and
deregistering an I2C adapter device which is assumed to manage that
I2C device may lead to a NULL pointer dereference due to the
uninitialized list head of driver clients.
The root cause of the issue is that the I2C bus may know about the
registered device driver and thus it is matched by bus_for_each_drv(),
but the list of clients is not initialized and commonly it is NULL,
because I2C device drivers define struct i2c_driver as static and
clients field is expected to be initialized by I2C core:
i2c_register_driver() i2c_del_adapter()
driver_register() ...
bus_add_driver() ...
... bus_for_each_drv(..., __process_removed_adapter)
... i2c_do_del_adapter()
... list_for_each_entry_safe(..., &driver->clients, ...)
INIT_LIST_HEAD(&driver->clients);
To solve the problem it is sufficient to do clients list head
initialization before calling driver_register().
The problem was found while using an I2C device driver with a sluggish
registration routine on a bus provided by a physically detachable I2C
master controller, but practically the oops may be reproduced under
the race between arbitraty I2C device driver registration and managing
I2C bus device removal e.g. by unbinding the latter over sysfs:
% echo 21a4000.i2c > /sys/bus/platform/drivers/imx-i2c/unbind
Unable to handle kernel NULL pointer dereference at virtual address 00000000
Internal error: Oops: 17 [#1] SMP ARM
CPU: 2 PID: 533 Comm: sh Not tainted 4.9.0-rc3+ #61
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
task: e5ada400 task.stack: e4936000
PC is at i2c_do_del_adapter+0x20/0xcc
LR is at __process_removed_adapter+0x14/0x1c
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 35bd004a DAC: 00000051
Process sh (pid: 533, stack limit = 0xe4936210)
Stack: (0xe4937d28 to 0xe4938000)
Backtrace:
[<c0667be0>] (i2c_do_del_adapter) from [<c0667cc0>] (__process_removed_adapter+0x14/0x1c)
[<c0667cac>] (__process_removed_adapter) from [<c0516998>] (bus_for_each_drv+0x6c/0xa0)
[<c051692c>] (bus_for_each_drv) from [<c06685ec>] (i2c_del_adapter+0xbc/0x284)
[<c0668530>] (i2c_del_adapter) from [<bf0110ec>] (i2c_imx_remove+0x44/0x164 [i2c_imx])
[<bf0110a8>] (i2c_imx_remove [i2c_imx]) from [<c051a838>] (platform_drv_remove+0x2c/0x44)
[<c051a80c>] (platform_drv_remove) from [<c05183d8>] (__device_release_driver+0x90/0x12c)
[<c0518348>] (__device_release_driver) from [<c051849c>] (device_release_driver+0x28/0x34)
[<c0518474>] (device_release_driver) from [<c0517150>] (unbind_store+0x80/0x104)
[<c05170d0>] (unbind_store) from [<c0516520>] (drv_attr_store+0x28/0x34)
[<c05164f8>] (drv_attr_store) from [<c0298acc>] (sysfs_kf_write+0x50/0x54)
[<c0298a7c>] (sysfs_kf_write) from [<c029801c>] (kernfs_fop_write+0x100/0x214)
[<c0297f1c>] (kernfs_fop_write) from [<c0220130>] (__vfs_write+0x34/0x120)
[<c02200fc>] (__vfs_write) from [<c0221088>] (vfs_write+0xa8/0x170)
[<c0220fe0>] (vfs_write) from [<c0221e74>] (SyS_write+0x4c/0xa8)
[<c0221e28>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 603616017c35f4d0fbdbcace72adf9bf949c4a65 upstream.
SMBus block command uses the first byte of buffer for the data length.
The dma_buffer should be increased by 1 to avoid the overrun issue.
Reported-by: Phil Endecott <phil_gjouf_endecott@chezphil.org>
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
This reverts commit 9d25c78ec01c402dc56272693c44ef9d72ecdd2e which is
1c109fabbd51863475cd12ac206bdd249aee35af upstream
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit fcf5e5198b447969ed2a56ec335dae3c695a6b46 which is
548acf19234dbda5a52d5a8e7e205af46e9da840 upstream.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
