diff options
Diffstat (limited to 'drivers/net/ixgbe/ixgbe_82599.c')
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_82599.c | 1489 |
1 files changed, 1382 insertions, 107 deletions
diff --git a/drivers/net/ixgbe/ixgbe_82599.c b/drivers/net/ixgbe/ixgbe_82599.c index 29771fbaa42d..1984cab7d48b 100644 --- a/drivers/net/ixgbe/ixgbe_82599.c +++ b/drivers/net/ixgbe/ixgbe_82599.c @@ -71,10 +71,10 @@ s32 ixgbe_clear_vfta_82599(struct ixgbe_hw *hw); s32 ixgbe_init_uta_tables_82599(struct ixgbe_hw *hw); s32 ixgbe_read_analog_reg8_82599(struct ixgbe_hw *hw, u32 reg, u8 *val); s32 ixgbe_write_analog_reg8_82599(struct ixgbe_hw *hw, u32 reg, u8 val); -s32 ixgbe_start_hw_rev_0_82599(struct ixgbe_hw *hw); s32 ixgbe_identify_phy_82599(struct ixgbe_hw *hw); s32 ixgbe_start_hw_82599(struct ixgbe_hw *hw); u32 ixgbe_get_supported_physical_layer_82599(struct ixgbe_hw *hw); +static s32 ixgbe_verify_fw_version_82599(struct ixgbe_hw *hw); void ixgbe_init_mac_link_ops_82599(struct ixgbe_hw *hw) { @@ -100,22 +100,36 @@ s32 ixgbe_setup_sfp_modules_82599(struct ixgbe_hw *hw) if (hw->phy.sfp_type != ixgbe_sfp_type_unknown) { ixgbe_init_mac_link_ops_82599(hw); + + hw->phy.ops.reset = NULL; + ret_val = ixgbe_get_sfp_init_sequence_offsets(hw, &list_offset, &data_offset); if (ret_val != 0) goto setup_sfp_out; + /* PHY config will finish before releasing the semaphore */ + ret_val = ixgbe_acquire_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM); + if (ret_val != 0) { + ret_val = IXGBE_ERR_SWFW_SYNC; + goto setup_sfp_out; + } + hw->eeprom.ops.read(hw, ++data_offset, &data_value); while (data_value != 0xffff) { IXGBE_WRITE_REG(hw, IXGBE_CORECTL, data_value); IXGBE_WRITE_FLUSH(hw); hw->eeprom.ops.read(hw, ++data_offset, &data_value); } - /* Now restart DSP */ - IXGBE_WRITE_REG(hw, IXGBE_CORECTL, 0x00000102); - IXGBE_WRITE_REG(hw, IXGBE_CORECTL, 0x00000b1d); - IXGBE_WRITE_FLUSH(hw); + /* Now restart DSP by setting Restart_AN */ + IXGBE_WRITE_REG(hw, IXGBE_AUTOC, + (IXGBE_READ_REG(hw, IXGBE_AUTOC) | IXGBE_AUTOC_AN_RESTART)); + + /* Release the semaphore */ + ixgbe_release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM); + /* Delay obtaining semaphore again to allow FW access */ + msleep(hw->eeprom.semaphore_delay); } setup_sfp_out: @@ -146,51 +160,60 @@ u32 ixgbe_get_pcie_msix_count_82599(struct ixgbe_hw *hw) static s32 ixgbe_get_invariants_82599(struct ixgbe_hw *hw) { struct ixgbe_mac_info *mac = &hw->mac; - struct ixgbe_phy_info *phy = &hw->phy; - s32 ret_val; - /* Set the bus information prior to PHY identification */ - mac->ops.get_bus_info(hw); + ixgbe_init_mac_link_ops_82599(hw); - /* Call PHY identify routine to get the Cu or SFI phy type */ - ret_val = phy->ops.identify(hw); + mac->mcft_size = IXGBE_82599_MC_TBL_SIZE; + mac->vft_size = IXGBE_82599_VFT_TBL_SIZE; + mac->num_rar_entries = IXGBE_82599_RAR_ENTRIES; + mac->max_rx_queues = IXGBE_82599_MAX_RX_QUEUES; + mac->max_tx_queues = IXGBE_82599_MAX_TX_QUEUES; + mac->max_msix_vectors = ixgbe_get_pcie_msix_count_82599(hw); - if (ret_val == IXGBE_ERR_SFP_NOT_SUPPORTED) - goto get_invariants_out; + return 0; +} - ixgbe_init_mac_link_ops_82599(hw); +/** + * ixgbe_init_phy_ops_82599 - PHY/SFP specific init + * @hw: pointer to hardware structure + * + * Initialize any function pointers that were not able to be + * set during get_invariants because the PHY/SFP type was + * not known. Perform the SFP init if necessary. + * + **/ +s32 ixgbe_init_phy_ops_82599(struct ixgbe_hw *hw) +{ + struct ixgbe_mac_info *mac = &hw->mac; + struct ixgbe_phy_info *phy = &hw->phy; + s32 ret_val = 0; - /* Setup SFP module if there is one present. */ - ret_val = mac->ops.setup_sfp(hw); + /* Identify the PHY or SFP module */ + ret_val = phy->ops.identify(hw); + + /* Setup function pointers based on detected SFP module and speeds */ + ixgbe_init_mac_link_ops_82599(hw); /* If copper media, overwrite with copper function pointers */ if (mac->ops.get_media_type(hw) == ixgbe_media_type_copper) { mac->ops.setup_link = &ixgbe_setup_copper_link_82599; mac->ops.setup_link_speed = - &ixgbe_setup_copper_link_speed_82599; + &ixgbe_setup_copper_link_speed_82599; mac->ops.get_link_capabilities = &ixgbe_get_copper_link_capabilities_82599; } - /* PHY Init */ + /* Set necessary function pointers based on phy type */ switch (hw->phy.type) { case ixgbe_phy_tn: phy->ops.check_link = &ixgbe_check_phy_link_tnx; phy->ops.get_firmware_version = - &ixgbe_get_phy_firmware_version_tnx; + &ixgbe_get_phy_firmware_version_tnx; break; default: break; } - mac->mcft_size = IXGBE_82599_MC_TBL_SIZE; - mac->vft_size = IXGBE_82599_VFT_TBL_SIZE; - mac->num_rar_entries = IXGBE_82599_RAR_ENTRIES; - mac->max_rx_queues = IXGBE_82599_MAX_RX_QUEUES; - mac->max_tx_queues = IXGBE_82599_MAX_TX_QUEUES; - mac->max_msix_vectors = ixgbe_get_pcie_msix_count_82599(hw); - -get_invariants_out: return ret_val; } @@ -207,8 +230,19 @@ s32 ixgbe_get_link_capabilities_82599(struct ixgbe_hw *hw, bool *negotiation) { s32 status = 0; + u32 autoc = 0; + + /* + * Determine link capabilities based on the stored value of AUTOC, + * which represents EEPROM defaults. If AUTOC value has not been + * stored, use the current register value. + */ + if (hw->mac.orig_link_settings_stored) + autoc = hw->mac.orig_autoc; + else + autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC); - switch (hw->mac.orig_autoc & IXGBE_AUTOC_LMS_MASK) { + switch (autoc & IXGBE_AUTOC_LMS_MASK) { case IXGBE_AUTOC_LMS_1G_LINK_NO_AN: *speed = IXGBE_LINK_SPEED_1GB_FULL; *negotiation = false; @@ -232,22 +266,22 @@ s32 ixgbe_get_link_capabilities_82599(struct ixgbe_hw *hw, case IXGBE_AUTOC_LMS_KX4_KX_KR: case IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN: *speed = IXGBE_LINK_SPEED_UNKNOWN; - if (hw->mac.orig_autoc & IXGBE_AUTOC_KR_SUPP) + if (autoc & IXGBE_AUTOC_KR_SUPP) *speed |= IXGBE_LINK_SPEED_10GB_FULL; - if (hw->mac.orig_autoc & IXGBE_AUTOC_KX4_SUPP) + if (autoc & IXGBE_AUTOC_KX4_SUPP) *speed |= IXGBE_LINK_SPEED_10GB_FULL; - if (hw->mac.orig_autoc & IXGBE_AUTOC_KX_SUPP) + if (autoc & IXGBE_AUTOC_KX_SUPP) *speed |= IXGBE_LINK_SPEED_1GB_FULL; *negotiation = true; break; case IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII: *speed = IXGBE_LINK_SPEED_100_FULL; - if (hw->mac.orig_autoc & IXGBE_AUTOC_KR_SUPP) + if (autoc & IXGBE_AUTOC_KR_SUPP) *speed |= IXGBE_LINK_SPEED_10GB_FULL; - if (hw->mac.orig_autoc & IXGBE_AUTOC_KX4_SUPP) + if (autoc & IXGBE_AUTOC_KX4_SUPP) *speed |= IXGBE_LINK_SPEED_10GB_FULL; - if (hw->mac.orig_autoc & IXGBE_AUTOC_KX_SUPP) + if (autoc & IXGBE_AUTOC_KX_SUPP) *speed |= IXGBE_LINK_SPEED_1GB_FULL; *negotiation = true; break; @@ -291,14 +325,13 @@ static s32 ixgbe_get_copper_link_capabilities_82599(struct ixgbe_hw *hw, *speed = 0; *autoneg = true; - status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_SPEED_ABILITY, - IXGBE_MDIO_PMA_PMD_DEV_TYPE, + status = hw->phy.ops.read_reg(hw, MDIO_SPEED, MDIO_MMD_PMAPMD, &speed_ability); if (status == 0) { - if (speed_ability & IXGBE_MDIO_PHY_SPEED_10G) + if (speed_ability & MDIO_SPEED_10G) *speed |= IXGBE_LINK_SPEED_10GB_FULL; - if (speed_ability & IXGBE_MDIO_PHY_SPEED_1G) + if (speed_ability & MDIO_PMA_SPEED_1000) *speed |= IXGBE_LINK_SPEED_1GB_FULL; } @@ -323,8 +356,8 @@ enum ixgbe_media_type ixgbe_get_media_type_82599(struct ixgbe_hw *hw) } switch (hw->device_id) { - case IXGBE_DEV_ID_82599: case IXGBE_DEV_ID_82599_KX4: + case IXGBE_DEV_ID_82599_XAUI_LOM: /* Default device ID is mezzanine card KX/KX4 */ media_type = ixgbe_media_type_backplane; break; @@ -380,9 +413,6 @@ s32 ixgbe_setup_mac_link_82599(struct ixgbe_hw *hw) } } - /* Set up flow control */ - status = ixgbe_setup_fc_generic(hw, 0); - /* Add delay to filter out noises during initial link setup */ msleep(50); @@ -428,11 +458,31 @@ s32 ixgbe_setup_mac_link_speed_multispeed_fiber(struct ixgbe_hw *hw, u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP); bool link_up = false; bool negotiation; + int i; /* Mask off requested but non-supported speeds */ hw->mac.ops.get_link_capabilities(hw, &phy_link_speed, &negotiation); speed &= phy_link_speed; + /* Set autoneg_advertised value based on input link speed */ + hw->phy.autoneg_advertised = 0; + + if (speed & IXGBE_LINK_SPEED_10GB_FULL) + hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL; + + if (speed & IXGBE_LINK_SPEED_1GB_FULL) + hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL; + + /* + * When the driver changes the link speeds that it can support, + * it sets autotry_restart to true to indicate that we need to + * initiate a new autotry session with the link partner. To do + * so, we set the speed then disable and re-enable the tx laser, to + * alert the link partner that it also needs to restart autotry on its + * end. This is consistent with true clause 37 autoneg, which also + * involves a loss of signal. + */ + /* * Try each speed one by one, highest priority first. We do this in * software because 10gb fiber doesn't support speed autonegotiation. @@ -441,21 +491,52 @@ s32 ixgbe_setup_mac_link_speed_multispeed_fiber(struct ixgbe_hw *hw, speedcnt++; highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL; - /* Set hardware SDP's */ + /* If we already have link at this speed, just jump out */ + hw->mac.ops.check_link(hw, &phy_link_speed, &link_up, false); + + if ((phy_link_speed == IXGBE_LINK_SPEED_10GB_FULL) && link_up) + goto out; + + /* Set the module link speed */ esdp_reg |= (IXGBE_ESDP_SDP5_DIR | IXGBE_ESDP_SDP5); IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); - ixgbe_setup_mac_link_speed_82599(hw, - IXGBE_LINK_SPEED_10GB_FULL, - autoneg, - autoneg_wait_to_complete); + /* Allow module to change analog characteristics (1G->10G) */ + msleep(40); - msleep(50); - - /* If we have link, just jump out */ - hw->mac.ops.check_link(hw, &phy_link_speed, &link_up, false); - if (link_up) + status = ixgbe_setup_mac_link_speed_82599(hw, + IXGBE_LINK_SPEED_10GB_FULL, + autoneg, + autoneg_wait_to_complete); + if (status != 0) goto out; + + /* Flap the tx laser if it has not already been done */ + if (hw->mac.autotry_restart) { + /* Disable tx laser; allow 100us to go dark per spec */ + esdp_reg |= IXGBE_ESDP_SDP3; + IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); + udelay(100); + + /* Enable tx laser; allow 2ms to light up per spec */ + esdp_reg &= ~IXGBE_ESDP_SDP3; + IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); + msleep(2); + + hw->mac.autotry_restart = false; + } + + /* The controller may take up to 500ms at 10g to acquire link */ + for (i = 0; i < 5; i++) { + /* Wait for the link partner to also set speed */ + msleep(100); + + /* If we have link, just jump out */ + hw->mac.ops.check_link(hw, &phy_link_speed, + &link_up, false); + if (link_up) + goto out; + } } if (speed & IXGBE_LINK_SPEED_1GB_FULL) { @@ -463,16 +544,44 @@ s32 ixgbe_setup_mac_link_speed_multispeed_fiber(struct ixgbe_hw *hw, if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN) highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL; - /* Set hardware SDP's */ + /* If we already have link at this speed, just jump out */ + hw->mac.ops.check_link(hw, &phy_link_speed, &link_up, false); + + if ((phy_link_speed == IXGBE_LINK_SPEED_1GB_FULL) && link_up) + goto out; + + /* Set the module link speed */ esdp_reg &= ~IXGBE_ESDP_SDP5; esdp_reg |= IXGBE_ESDP_SDP5_DIR; IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); - ixgbe_setup_mac_link_speed_82599( - hw, IXGBE_LINK_SPEED_1GB_FULL, autoneg, - autoneg_wait_to_complete); + /* Allow module to change analog characteristics (10G->1G) */ + msleep(40); - msleep(50); + status = ixgbe_setup_mac_link_speed_82599(hw, + IXGBE_LINK_SPEED_1GB_FULL, + autoneg, + autoneg_wait_to_complete); + if (status != 0) + goto out; + + /* Flap the tx laser if it has not already been done */ + if (hw->mac.autotry_restart) { + /* Disable tx laser; allow 100us to go dark per spec */ + esdp_reg |= IXGBE_ESDP_SDP3; + IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); + udelay(100); + + /* Enable tx laser; allow 2ms to light up per spec */ + esdp_reg &= ~IXGBE_ESDP_SDP3; + IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); + msleep(2); + + hw->mac.autotry_restart = false; + } + + /* Wait for the link partner to also set speed */ + msleep(100); /* If we have link, just jump out */ hw->mac.ops.check_link(hw, &phy_link_speed, &link_up, false); @@ -538,6 +647,11 @@ s32 ixgbe_check_mac_link_82599(struct ixgbe_hw *hw, ixgbe_link_speed *speed, else *speed = IXGBE_LINK_SPEED_100_FULL; + /* if link is down, zero out the current_mode */ + if (*link_up == false) { + hw->fc.current_mode = ixgbe_fc_none; + hw->fc.fc_was_autonegged = false; + } return 0; } @@ -558,6 +672,8 @@ s32 ixgbe_setup_mac_link_speed_82599(struct ixgbe_hw *hw, s32 status = 0; u32 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC); u32 autoc2 = IXGBE_READ_REG(hw, IXGBE_AUTOC2); + u32 start_autoc = autoc; + u32 orig_autoc = 0; u32 link_mode = autoc & IXGBE_AUTOC_LMS_MASK; u32 pma_pmd_1g = autoc & IXGBE_AUTOC_1G_PMA_PMD_MASK; u32 pma_pmd_10g_serial = autoc2 & IXGBE_AUTOC2_10G_SERIAL_PMA_PMD_MASK; @@ -571,15 +687,25 @@ s32 ixgbe_setup_mac_link_speed_82599(struct ixgbe_hw *hw, if (speed == IXGBE_LINK_SPEED_UNKNOWN) { status = IXGBE_ERR_LINK_SETUP; - } else if (link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR || - link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN || - link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII) { + goto out; + } + + /* Use stored value (EEPROM defaults) of AUTOC to find KR/KX4 support*/ + if (hw->mac.orig_link_settings_stored) + orig_autoc = hw->mac.orig_autoc; + else + orig_autoc = autoc; + + + if (link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR || + link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN || + link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII) { /* Set KX4/KX/KR support according to speed requested */ autoc &= ~(IXGBE_AUTOC_KX4_KX_SUPP_MASK | IXGBE_AUTOC_KR_SUPP); if (speed & IXGBE_LINK_SPEED_10GB_FULL) - if (hw->mac.orig_autoc & IXGBE_AUTOC_KX4_SUPP) + if (orig_autoc & IXGBE_AUTOC_KX4_SUPP) autoc |= IXGBE_AUTOC_KX4_SUPP; - if (hw->mac.orig_autoc & IXGBE_AUTOC_KR_SUPP) + if (orig_autoc & IXGBE_AUTOC_KR_SUPP) autoc |= IXGBE_AUTOC_KR_SUPP; if (speed & IXGBE_LINK_SPEED_1GB_FULL) autoc |= IXGBE_AUTOC_KX_SUPP; @@ -605,7 +731,7 @@ s32 ixgbe_setup_mac_link_speed_82599(struct ixgbe_hw *hw, } } - if (status == 0) { + if (autoc != start_autoc) { /* Restart link */ autoc |= IXGBE_AUTOC_AN_RESTART; IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc); @@ -632,13 +758,11 @@ s32 ixgbe_setup_mac_link_speed_82599(struct ixgbe_hw *hw, } } - /* Set up flow control */ - status = ixgbe_setup_fc_generic(hw, 0); - /* Add delay to filter out noises during initial link setup */ msleep(50); } +out: return status; } @@ -705,14 +829,30 @@ s32 ixgbe_reset_hw_82599(struct ixgbe_hw *hw) /* Call adapter stop to disable tx/rx and clear interrupts */ hw->mac.ops.stop_adapter(hw); + /* PHY ops must be identified and initialized prior to reset */ + + /* Init PHY and function pointers, perform SFP setup */ + status = hw->phy.ops.init(hw); + + if (status == IXGBE_ERR_SFP_NOT_SUPPORTED) + goto reset_hw_out; + + /* Setup SFP module if there is one present. */ + if (hw->phy.sfp_setup_needed) { + status = hw->mac.ops.setup_sfp(hw); + hw->phy.sfp_setup_needed = false; + } + /* Reset PHY */ - hw->phy.ops.reset(hw); + if (hw->phy.reset_disable == false && hw->phy.ops.reset != NULL) + hw->phy.ops.reset(hw); /* * Prevent the PCI-E bus from from hanging by disabling PCI-E master * access and verify no pending requests before reset */ - if (ixgbe_disable_pcie_master(hw) != 0) { + status = ixgbe_disable_pcie_master(hw); + if (status != 0) { status = IXGBE_ERR_MASTER_REQUESTS_PENDING; hw_dbg(hw, "PCI-E Master disable polling has failed.\n"); } @@ -770,9 +910,30 @@ s32 ixgbe_reset_hw_82599(struct ixgbe_hw *hw) } } + /* + * Store MAC address from RAR0, clear receive address registers, and + * clear the multicast table. Also reset num_rar_entries to 128, + * since we modify this value when programming the SAN MAC address. + */ + hw->mac.num_rar_entries = 128; + hw->mac.ops.init_rx_addrs(hw); + /* Store the permanent mac address */ hw->mac.ops.get_mac_addr(hw, hw->mac.perm_addr); + /* Store the permanent SAN mac address */ + hw->mac.ops.get_san_mac_addr(hw, hw->mac.san_addr); + + /* Add the SAN MAC address to the RAR only if it's a valid address */ + if (ixgbe_validate_mac_addr(hw->mac.san_addr) == 0) { + hw->mac.ops.set_rar(hw, hw->mac.num_rar_entries - 1, + hw->mac.san_addr, 0, IXGBE_RAH_AV); + + /* Reserve the last RAR for the SAN MAC address */ + hw->mac.num_rar_entries--; + } + +reset_hw_out: return status; } @@ -1004,6 +1165,931 @@ s32 ixgbe_init_uta_tables_82599(struct ixgbe_hw *hw) } /** + * ixgbe_reinit_fdir_tables_82599 - Reinitialize Flow Director tables. + * @hw: pointer to hardware structure + **/ +s32 ixgbe_reinit_fdir_tables_82599(struct ixgbe_hw *hw) +{ + int i; + u32 fdirctrl = IXGBE_READ_REG(hw, IXGBE_FDIRCTRL); + fdirctrl &= ~IXGBE_FDIRCTRL_INIT_DONE; + + /* + * Before starting reinitialization process, + * FDIRCMD.CMD must be zero. + */ + for (i = 0; i < IXGBE_FDIRCMD_CMD_POLL; i++) { + if (!(IXGBE_READ_REG(hw, IXGBE_FDIRCMD) & + IXGBE_FDIRCMD_CMD_MASK)) + break; + udelay(10); + } + if (i >= IXGBE_FDIRCMD_CMD_POLL) { + hw_dbg(hw ,"Flow Director previous command isn't complete, " + "aborting table re-initialization. \n"); + return IXGBE_ERR_FDIR_REINIT_FAILED; + } + + IXGBE_WRITE_REG(hw, IXGBE_FDIRFREE, 0); + IXGBE_WRITE_FLUSH(hw); + /* + * 82599 adapters flow director init flow cannot be restarted, + * Workaround 82599 silicon errata by performing the following steps + * before re-writing the FDIRCTRL control register with the same value. + * - write 1 to bit 8 of FDIRCMD register & + * - write 0 to bit 8 of FDIRCMD register + */ + IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD, + (IXGBE_READ_REG(hw, IXGBE_FDIRCMD) | + IXGBE_FDIRCMD_CLEARHT)); + IXGBE_WRITE_FLUSH(hw); + IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD, + (IXGBE_READ_REG(hw, IXGBE_FDIRCMD) & + ~IXGBE_FDIRCMD_CLEARHT)); + IXGBE_WRITE_FLUSH(hw); + /* + * Clear FDIR Hash register to clear any leftover hashes + * waiting to be programmed. + */ + IXGBE_WRITE_REG(hw, IXGBE_FDIRHASH, 0x00); + IXGBE_WRITE_FLUSH(hw); + + IXGBE_WRITE_REG(hw, IXGBE_FDIRCTRL, fdirctrl); + IXGBE_WRITE_FLUSH(hw); + + /* Poll init-done after we write FDIRCTRL register */ + for (i = 0; i < IXGBE_FDIR_INIT_DONE_POLL; i++) { + if (IXGBE_READ_REG(hw, IXGBE_FDIRCTRL) & + IXGBE_FDIRCTRL_INIT_DONE) + break; + udelay(10); + } + if (i >= IXGBE_FDIR_INIT_DONE_POLL) { + hw_dbg(hw, "Flow Director Signature poll time exceeded!\n"); + return IXGBE_ERR_FDIR_REINIT_FAILED; + } + + /* Clear FDIR statistics registers (read to clear) */ + IXGBE_READ_REG(hw, IXGBE_FDIRUSTAT); + IXGBE_READ_REG(hw, IXGBE_FDIRFSTAT); + IXGBE_READ_REG(hw, IXGBE_FDIRMATCH); + IXGBE_READ_REG(hw, IXGBE_FDIRMISS); + IXGBE_READ_REG(hw, IXGBE_FDIRLEN); + + return 0; +} + +/** + * ixgbe_init_fdir_signature_82599 - Initialize Flow Director signature filters + * @hw: pointer to hardware structure + * @pballoc: which mode to allocate filters with + **/ +s32 ixgbe_init_fdir_signature_82599(struct ixgbe_hw *hw, u32 pballoc) +{ + u32 fdirctrl = 0; + u32 pbsize; + int i; + + /* + * Before enabling Flow Director, the Rx Packet Buffer size + * must be reduced. The new value is the current size minus + * flow director memory usage size. + */ + pbsize = (1 << (IXGBE_FDIR_PBALLOC_SIZE_SHIFT + pballoc)); + IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(0), + (IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(0)) - pbsize)); + + /* + * The defaults in the HW for RX PB 1-7 are not zero and so should be + * intialized to zero for non DCB mode otherwise actual total RX PB + * would be bigger than programmed and filter space would run into + * the PB 0 region. + */ + for (i = 1; i < 8; i++) + IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), 0); + + /* Send interrupt when 64 filters are left */ + fdirctrl |= 4 << IXGBE_FDIRCTRL_FULL_THRESH_SHIFT; + + /* Set the maximum length per hash bucket to 0xA filters */ + fdirctrl |= 0xA << IXGBE_FDIRCTRL_MAX_LENGTH_SHIFT; + + switch (pballoc) { + case IXGBE_FDIR_PBALLOC_64K: + /* 8k - 1 signature filters */ + fdirctrl |= IXGBE_FDIRCTRL_PBALLOC_64K; + break; + case IXGBE_FDIR_PBALLOC_128K: + /* 16k - 1 signature filters */ + fdirctrl |= IXGBE_FDIRCTRL_PBALLOC_128K; + break; + case IXGBE_FDIR_PBALLOC_256K: + /* 32k - 1 signature filters */ + fdirctrl |= IXGBE_FDIRCTRL_PBALLOC_256K; + break; + default: + /* bad value */ + return IXGBE_ERR_CONFIG; + }; + + /* Move the flexible bytes to use the ethertype - shift 6 words */ + fdirctrl |= (0x6 << IXGBE_FDIRCTRL_FLEX_SHIFT); + + fdirctrl |= IXGBE_FDIRCTRL_REPORT_STATUS; + + /* Prime the keys for hashing */ + IXGBE_WRITE_REG(hw, IXGBE_FDIRHKEY, + htonl(IXGBE_ATR_BUCKET_HASH_KEY)); + IXGBE_WRITE_REG(hw, IXGBE_FDIRSKEY, + htonl(IXGBE_ATR_SIGNATURE_HASH_KEY)); + + /* + * Poll init-done after we write the register. Estimated times: + * 10G: PBALLOC = 11b, timing is 60us + * 1G: PBALLOC = 11b, timing is 600us + * 100M: PBALLOC = 11b, timing is 6ms + * + * Multiple these timings by 4 if under full Rx load + * + * So we'll poll for IXGBE_FDIR_INIT_DONE_POLL times, sleeping for + * 1 msec per poll time. If we're at line rate and drop to 100M, then + * this might not finish in our poll time, but we can live with that + * for now. + */ + IXGBE_WRITE_REG(hw, IXGBE_FDIRCTRL, fdirctrl); + IXGBE_WRITE_FLUSH(hw); + for (i = 0; i < IXGBE_FDIR_INIT_DONE_POLL; i++) { + if (IXGBE_READ_REG(hw, IXGBE_FDIRCTRL) & + IXGBE_FDIRCTRL_INIT_DONE) + break; + msleep(1); + } + if (i >= IXGBE_FDIR_INIT_DONE_POLL) + hw_dbg(hw, "Flow Director Signature poll time exceeded!\n"); + + return 0; +} + +/** + * ixgbe_init_fdir_perfect_82599 - Initialize Flow Director perfect filters + * @hw: pointer to hardware structure + * @pballoc: which mode to allocate filters with + **/ +s32 ixgbe_init_fdir_perfect_82599(struct ixgbe_hw *hw, u32 pballoc) +{ + u32 fdirctrl = 0; + u32 pbsize; + int i; + + /* + * Before enabling Flow Director, the Rx Packet Buffer size + * must be reduced. The new value is the current size minus + * flow director memory usage size. + */ + pbsize = (1 << (IXGBE_FDIR_PBALLOC_SIZE_SHIFT + pballoc)); + IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(0), + (IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(0)) - pbsize)); + + /* + * The defaults in the HW for RX PB 1-7 are not zero and so should be + * intialized to zero for non DCB mode otherwise actual total RX PB + * would be bigger than programmed and filter space would run into + * the PB 0 region. + */ + for (i = 1; i < 8; i++) + IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), 0); + + /* Send interrupt when 64 filters are left */ + fdirctrl |= 4 << IXGBE_FDIRCTRL_FULL_THRESH_SHIFT; + + switch (pballoc) { + case IXGBE_FDIR_PBALLOC_64K: + /* 2k - 1 perfect filters */ + fdirctrl |= IXGBE_FDIRCTRL_PBALLOC_64K; + break; + case IXGBE_FDIR_PBALLOC_128K: + /* 4k - 1 perfect filters */ + fdirctrl |= IXGBE_FDIRCTRL_PBALLOC_128K; + break; + case IXGBE_FDIR_PBALLOC_256K: + /* 8k - 1 perfect filters */ + fdirctrl |= IXGBE_FDIRCTRL_PBALLOC_256K; + break; + default: + /* bad value */ + return IXGBE_ERR_CONFIG; + }; + + /* Turn perfect match filtering on */ + fdirctrl |= IXGBE_FDIRCTRL_PERFECT_MATCH; + fdirctrl |= IXGBE_FDIRCTRL_REPORT_STATUS; + + /* Move the flexible bytes to use the ethertype - shift 6 words */ + fdirctrl |= (0x6 << IXGBE_FDIRCTRL_FLEX_SHIFT); + + /* Prime the keys for hashing */ + IXGBE_WRITE_REG(hw, IXGBE_FDIRHKEY, + htonl(IXGBE_ATR_BUCKET_HASH_KEY)); + IXGBE_WRITE_REG(hw, IXGBE_FDIRSKEY, + htonl(IXGBE_ATR_SIGNATURE_HASH_KEY)); + + /* + * Poll init-done after we write the register. Estimated times: + * 10G: PBALLOC = 11b, timing is 60us + * 1G: PBALLOC = 11b, timing is 600us + * 100M: PBALLOC = 11b, timing is 6ms + * + * Multiple these timings by 4 if under full Rx load + * + * So we'll poll for IXGBE_FDIR_INIT_DONE_POLL times, sleeping for + * 1 msec per poll time. If we're at line rate and drop to 100M, then + * this might not finish in our poll time, but we can live with that + * for now. + */ + + /* Set the maximum length per hash bucket to 0xA filters */ + fdirctrl |= (0xA << IXGBE_FDIRCTRL_MAX_LENGTH_SHIFT); + + IXGBE_WRITE_REG(hw, IXGBE_FDIRCTRL, fdirctrl); + IXGBE_WRITE_FLUSH(hw); + for (i = 0; i < IXGBE_FDIR_INIT_DONE_POLL; i++) { + if (IXGBE_READ_REG(hw, IXGBE_FDIRCTRL) & + IXGBE_FDIRCTRL_INIT_DONE) + break; + msleep(1); + } + if (i >= IXGBE_FDIR_INIT_DONE_POLL) + hw_dbg(hw, "Flow Director Perfect poll time exceeded!\n"); + + return 0; +} + + +/** + * ixgbe_atr_compute_hash_82599 - Compute the hashes for SW ATR + * @stream: input bitstream to compute the hash on + * @key: 32-bit hash key + **/ +u16 ixgbe_atr_compute_hash_82599(struct ixgbe_atr_input *atr_input, u32 key) +{ + /* + * The algorithm is as follows: + * Hash[15:0] = Sum { S[n] x K[n+16] }, n = 0...350 + * where Sum {A[n]}, n = 0...n is bitwise XOR of A[0], A[1]...A[n] + * and A[n] x B[n] is bitwise AND between same length strings + * + * K[n] is 16 bits, defined as: + * for n modulo 32 >= 15, K[n] = K[n % 32 : (n % 32) - 15] + * for n modulo 32 < 15, K[n] = + * K[(n % 32:0) | (31:31 - (14 - (n % 32)))] + * + * S[n] is 16 bits, defined as: + * for n >= 15, S[n] = S[n:n - 15] + * for n < 15, S[n] = S[(n:0) | (350:350 - (14 - n))] + * + * To simplify for programming, the algorithm is implemented + * in software this way: + * + * Key[31:0], Stream[335:0] + * + * tmp_key[11 * 32 - 1:0] = 11{Key[31:0] = key concatenated 11 times + * int_key[350:0] = tmp_key[351:1] + * int_stream[365:0] = Stream[14:0] | Stream[335:0] | Stream[335:321] + * + * hash[15:0] = 0; + * for (i = 0; i < 351; i++) { + * if (int_key[i]) + * hash ^= int_stream[(i + 15):i]; + * } + */ + + union { + u64 fill[6]; + u32 key[11]; + u8 key_stream[44]; + } tmp_key; + + u8 *stream = (u8 *)atr_input; + u8 int_key[44]; /* upper-most bit unused */ + u8 hash_str[46]; /* upper-most 2 bits unused */ + u16 hash_result = 0; + int i, j, k, h; + + /* + * Initialize the fill member to prevent warnings + * on some compilers + */ + tmp_key.fill[0] = 0; + + /* First load the temporary key stream */ + for (i = 0; i < 6; i++) { + u64 fillkey = ((u64)key << 32) | key; + tmp_key.fill[i] = fillkey; + } + + /* + * Set the interim key for the hashing. Bit 352 is unused, so we must + * shift and compensate when building the key. + */ + + int_key[0] = tmp_key.key_stream[0] >> 1; + for (i = 1, j = 0; i < 44; i++) { + unsigned int this_key = tmp_key.key_stream[j] << 7; + j++; + int_key[i] = (u8)(this_key | (tmp_key.key_stream[j] >> 1)); + } + + /* + * Set the interim bit string for the hashing. Bits 368 and 367 are + * unused, so shift and compensate when building the string. + */ + hash_str[0] = (stream[40] & 0x7f) >> 1; + for (i = 1, j = 40; i < 46; i++) { + unsigned int this_str = stream[j] << 7; + j++; + if (j > 41) + j = 0; + hash_str[i] = (u8)(this_str | (stream[j] >> 1)); + } + + /* + * Now compute the hash. i is the index into hash_str, j is into our + * key stream, k is counting the number of bits, and h interates within + * each byte. + */ + for (i = 45, j = 43, k = 0; k < 351 && i >= 2 && j >= 0; i--, j--) { + for (h = 0; h < 8 && k < 351; h++, k++) { + if (int_key[j] & (1 << h)) { + /* + * Key bit is set, XOR in the current 16-bit + * string. Example of processing: + * h = 0, + * tmp = (hash_str[i - 2] & 0 << 16) | + * (hash_str[i - 1] & 0xff << 8) | + * (hash_str[i] & 0xff >> 0) + * So tmp = hash_str[15 + k:k], since the + * i + 2 clause rolls off the 16-bit value + * h = 7, + * tmp = (hash_str[i - 2] & 0x7f << 9) | + * (hash_str[i - 1] & 0xff << 1) | + * (hash_str[i] & 0x80 >> 7) + */ + int tmp = (hash_str[i] >> h); + tmp |= (hash_str[i - 1] << (8 - h)); + tmp |= (int)(hash_str[i - 2] & ((1 << h) - 1)) + << (16 - h); + hash_result ^= (u16)tmp; + } + } + } + + return hash_result; +} + +/** + * ixgbe_atr_set_vlan_id_82599 - Sets the VLAN id in the ATR input stream + * @input: input stream to modify + * @vlan: the VLAN id to load + **/ +s32 ixgbe_atr_set_vlan_id_82599(struct ixgbe_atr_input *input, u16 vlan) +{ + input->byte_stream[IXGBE_ATR_VLAN_OFFSET + 1] = vlan >> 8; + input->byte_stream[IXGBE_ATR_VLAN_OFFSET] = vlan & 0xff; + + return 0; +} + +/** + * ixgbe_atr_set_src_ipv4_82599 - Sets the source IPv4 address + * @input: input stream to modify + * @src_addr: the IP address to load + **/ +s32 ixgbe_atr_set_src_ipv4_82599(struct ixgbe_atr_input *input, u32 src_addr) +{ + input->byte_stream[IXGBE_ATR_SRC_IPV4_OFFSET + 3] = src_addr >> 24; + input->byte_stream[IXGBE_ATR_SRC_IPV4_OFFSET + 2] = + (src_addr >> 16) & 0xff; + input->byte_stream[IXGBE_ATR_SRC_IPV4_OFFSET + 1] = + (src_addr >> 8) & 0xff; + input->byte_stream[IXGBE_ATR_SRC_IPV4_OFFSET] = src_addr & 0xff; + + return 0; +} + +/** + * ixgbe_atr_set_dst_ipv4_82599 - Sets the destination IPv4 address + * @input: input stream to modify + * @dst_addr: the IP address to load + **/ +s32 ixgbe_atr_set_dst_ipv4_82599(struct ixgbe_atr_input *input, u32 dst_addr) +{ + input->byte_stream[IXGBE_ATR_DST_IPV4_OFFSET + 3] = dst_addr >> 24; + input->byte_stream[IXGBE_ATR_DST_IPV4_OFFSET + 2] = + (dst_addr >> 16) & 0xff; + input->byte_stream[IXGBE_ATR_DST_IPV4_OFFSET + 1] = + (dst_addr >> 8) & 0xff; + input->byte_stream[IXGBE_ATR_DST_IPV4_OFFSET] = dst_addr & 0xff; + + return 0; +} + +/** + * ixgbe_atr_set_src_ipv6_82599 - Sets the source IPv6 address + * @input: input stream to modify + * @src_addr_1: the first 4 bytes of the IP address to load + * @src_addr_2: the second 4 bytes of the IP address to load + * @src_addr_3: the third 4 bytes of the IP address to load + * @src_addr_4: the fourth 4 bytes of the IP address to load + **/ +s32 ixgbe_atr_set_src_ipv6_82599(struct ixgbe_atr_input *input, + u32 src_addr_1, u32 src_addr_2, + u32 src_addr_3, u32 src_addr_4) +{ + input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET] = src_addr_4 & 0xff; + input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 1] = + (src_addr_4 >> 8) & 0xff; + input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 2] = + (src_addr_4 >> 16) & 0xff; + input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 3] = src_addr_4 >> 24; + + input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 4] = src_addr_3 & 0xff; + input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 5] = + (src_addr_3 >> 8) & 0xff; + input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 6] = + (src_addr_3 >> 16) & 0xff; + input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 7] = src_addr_3 >> 24; + + input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 8] = src_addr_2 & 0xff; + input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 9] = + (src_addr_2 >> 8) & 0xff; + input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 10] = + (src_addr_2 >> 16) & 0xff; + input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 11] = src_addr_2 >> 24; + + input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 12] = src_addr_1 & 0xff; + input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 13] = + (src_addr_1 >> 8) & 0xff; + input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 14] = + (src_addr_1 >> 16) & 0xff; + input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 15] = src_addr_1 >> 24; + + return 0; +} + +/** + * ixgbe_atr_set_dst_ipv6_82599 - Sets the destination IPv6 address + * @input: input stream to modify + * @dst_addr_1: the first 4 bytes of the IP address to load + * @dst_addr_2: the second 4 bytes of the IP address to load + * @dst_addr_3: the third 4 bytes of the IP address to load + * @dst_addr_4: the fourth 4 bytes of the IP address to load + **/ +s32 ixgbe_atr_set_dst_ipv6_82599(struct ixgbe_atr_input *input, + u32 dst_addr_1, u32 dst_addr_2, + u32 dst_addr_3, u32 dst_addr_4) +{ + input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET] = dst_addr_4 & 0xff; + input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 1] = + (dst_addr_4 >> 8) & 0xff; + input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 2] = + (dst_addr_4 >> 16) & 0xff; + input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 3] = dst_addr_4 >> 24; + + input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 4] = dst_addr_3 & 0xff; + input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 5] = + (dst_addr_3 >> 8) & 0xff; + input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 6] = + (dst_addr_3 >> 16) & 0xff; + input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 7] = dst_addr_3 >> 24; + + input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 8] = dst_addr_2 & 0xff; + input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 9] = + (dst_addr_2 >> 8) & 0xff; + input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 10] = + (dst_addr_2 >> 16) & 0xff; + input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 11] = dst_addr_2 >> 24; + + input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 12] = dst_addr_1 & 0xff; + input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 13] = + (dst_addr_1 >> 8) & 0xff; + input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 14] = + (dst_addr_1 >> 16) & 0xff; + input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 15] = dst_addr_1 >> 24; + + return 0; +} + +/** + * ixgbe_atr_set_src_port_82599 - Sets the source port + * @input: input stream to modify + * @src_port: the source port to load + **/ +s32 ixgbe_atr_set_src_port_82599(struct ixgbe_atr_input *input, u16 src_port) +{ + input->byte_stream[IXGBE_ATR_SRC_PORT_OFFSET + 1] = src_port >> 8; + input->byte_stream[IXGBE_ATR_SRC_PORT_OFFSET] = src_port & 0xff; + + return 0; +} + +/** + * ixgbe_atr_set_dst_port_82599 - Sets the destination port + * @input: input stream to modify + * @dst_port: the destination port to load + **/ +s32 ixgbe_atr_set_dst_port_82599(struct ixgbe_atr_input *input, u16 dst_port) +{ + input->byte_stream[IXGBE_ATR_DST_PORT_OFFSET + 1] = dst_port >> 8; + input->byte_stream[IXGBE_ATR_DST_PORT_OFFSET] = dst_port & 0xff; + + return 0; +} + +/** + * ixgbe_atr_set_flex_byte_82599 - Sets the flexible bytes + * @input: input stream to modify + * @flex_bytes: the flexible bytes to load + **/ +s32 ixgbe_atr_set_flex_byte_82599(struct ixgbe_atr_input *input, u16 flex_byte) +{ + input->byte_stream[IXGBE_ATR_FLEX_BYTE_OFFSET + 1] = flex_byte >> 8; + input->byte_stream[IXGBE_ATR_FLEX_BYTE_OFFSET] = flex_byte & 0xff; + + return 0; +} + +/** + * ixgbe_atr_set_vm_pool_82599 - Sets the Virtual Machine pool + * @input: input stream to modify + * @vm_pool: the Virtual Machine pool to load + **/ +s32 ixgbe_atr_set_vm_pool_82599(struct ixgbe_atr_input *input, u8 vm_pool) +{ + input->byte_stream[IXGBE_ATR_VM_POOL_OFFSET] = vm_pool; + + return 0; +} + +/** + * ixgbe_atr_set_l4type_82599 - Sets the layer 4 packet type + * @input: input stream to modify + * @l4type: the layer 4 type value to load + **/ +s32 ixgbe_atr_set_l4type_82599(struct ixgbe_atr_input *input, u8 l4type) +{ + input->byte_stream[IXGBE_ATR_L4TYPE_OFFSET] = l4type; + + return 0; +} + +/** + * ixgbe_atr_get_vlan_id_82599 - Gets the VLAN id from the ATR input stream + * @input: input stream to search + * @vlan: the VLAN id to load + **/ +s32 ixgbe_atr_get_vlan_id_82599(struct ixgbe_atr_input *input, u16 *vlan) +{ + *vlan = input->byte_stream[IXGBE_ATR_VLAN_OFFSET]; + *vlan |= input->byte_stream[IXGBE_ATR_VLAN_OFFSET + 1] << 8; + + return 0; +} + +/** + * ixgbe_atr_get_src_ipv4_82599 - Gets the source IPv4 address + * @input: input stream to search + * @src_addr: the IP address to load + **/ +s32 ixgbe_atr_get_src_ipv4_82599(struct ixgbe_atr_input *input, u32 *src_addr) +{ + *src_addr = input->byte_stream[IXGBE_ATR_SRC_IPV4_OFFSET]; + *src_addr |= input->byte_stream[IXGBE_ATR_SRC_IPV4_OFFSET + 1] << 8; + *src_addr |= input->byte_stream[IXGBE_ATR_SRC_IPV4_OFFSET + 2] << 16; + *src_addr |= input->byte_stream[IXGBE_ATR_SRC_IPV4_OFFSET + 3] << 24; + + return 0; +} + +/** + * ixgbe_atr_get_dst_ipv4_82599 - Gets the destination IPv4 address + * @input: input stream to search + * @dst_addr: the IP address to load + **/ +s32 ixgbe_atr_get_dst_ipv4_82599(struct ixgbe_atr_input *input, u32 *dst_addr) +{ + *dst_addr = input->byte_stream[IXGBE_ATR_DST_IPV4_OFFSET]; + *dst_addr |= input->byte_stream[IXGBE_ATR_DST_IPV4_OFFSET + 1] << 8; + *dst_addr |= input->byte_stream[IXGBE_ATR_DST_IPV4_OFFSET + 2] << 16; + *dst_addr |= input->byte_stream[IXGBE_ATR_DST_IPV4_OFFSET + 3] << 24; + + return 0; +} + +/** + * ixgbe_atr_get_src_ipv6_82599 - Gets the source IPv6 address + * @input: input stream to search + * @src_addr_1: the first 4 bytes of the IP address to load + * @src_addr_2: the second 4 bytes of the IP address to load + * @src_addr_3: the third 4 bytes of the IP address to load + * @src_addr_4: the fourth 4 bytes of the IP address to load + **/ +s32 ixgbe_atr_get_src_ipv6_82599(struct ixgbe_atr_input *input, + u32 *src_addr_1, u32 *src_addr_2, + u32 *src_addr_3, u32 *src_addr_4) +{ + *src_addr_1 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 12]; + *src_addr_1 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 13] << 8; + *src_addr_1 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 14] << 16; + *src_addr_1 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 15] << 24; + + *src_addr_2 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 8]; + *src_addr_2 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 9] << 8; + *src_addr_2 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 10] << 16; + *src_addr_2 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 11] << 24; + + *src_addr_3 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 4]; + *src_addr_3 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 5] << 8; + *src_addr_3 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 6] << 16; + *src_addr_3 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 7] << 24; + + *src_addr_4 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET]; + *src_addr_4 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 1] << 8; + *src_addr_4 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 2] << 16; + *src_addr_4 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 3] << 24; + + return 0; +} + +/** + * ixgbe_atr_get_dst_ipv6_82599 - Gets the destination IPv6 address + * @input: input stream to search + * @dst_addr_1: the first 4 bytes of the IP address to load + * @dst_addr_2: the second 4 bytes of the IP address to load + * @dst_addr_3: the third 4 bytes of the IP address to load + * @dst_addr_4: the fourth 4 bytes of the IP address to load + **/ +s32 ixgbe_atr_get_dst_ipv6_82599(struct ixgbe_atr_input *input, + u32 *dst_addr_1, u32 *dst_addr_2, + u32 *dst_addr_3, u32 *dst_addr_4) +{ + *dst_addr_1 = input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 12]; + *dst_addr_1 = input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 13] << 8; + *dst_addr_1 = input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 14] << 16; + *dst_addr_1 = input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 15] << 24; + + *dst_addr_2 = input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 8]; + *dst_addr_2 = input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 9] << 8; + *dst_addr_2 = input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 10] << 16; + *dst_addr_2 = input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 11] << 24; + + *dst_addr_3 = input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 4]; + *dst_addr_3 = input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 5] << 8; + *dst_addr_3 = input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 6] << 16; + *dst_addr_3 = input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 7] << 24; + + *dst_addr_4 = input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET]; + *dst_addr_4 = input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 1] << 8; + *dst_addr_4 = input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 2] << 16; + *dst_addr_4 = input->byte_stream[IXGBE_ATR_DST_IPV6_OFFSET + 3] << 24; + + return 0; +} + +/** + * ixgbe_atr_get_src_port_82599 - Gets the source port + * @input: input stream to modify + * @src_port: the source port to load + * + * Even though the input is given in big-endian, the FDIRPORT registers + * expect the ports to be programmed in little-endian. Hence the need to swap + * endianness when retrieving the data. This can be confusing since the + * internal hash engine expects it to be big-endian. + **/ +s32 ixgbe_atr_get_src_port_82599(struct ixgbe_atr_input *input, u16 *src_port) +{ + *src_port = input->byte_stream[IXGBE_ATR_SRC_PORT_OFFSET] << 8; + *src_port |= input->byte_stream[IXGBE_ATR_SRC_PORT_OFFSET + 1]; + + return 0; +} + +/** + * ixgbe_atr_get_dst_port_82599 - Gets the destination port + * @input: input stream to modify + * @dst_port: the destination port to load + * + * Even though the input is given in big-endian, the FDIRPORT registers + * expect the ports to be programmed in little-endian. Hence the need to swap + * endianness when retrieving the data. This can be confusing since the + * internal hash engine expects it to be big-endian. + **/ +s32 ixgbe_atr_get_dst_port_82599(struct ixgbe_atr_input *input, u16 *dst_port) +{ + *dst_port = input->byte_stream[IXGBE_ATR_DST_PORT_OFFSET] << 8; + *dst_port |= input->byte_stream[IXGBE_ATR_DST_PORT_OFFSET + 1]; + + return 0; +} + +/** + * ixgbe_atr_get_flex_byte_82599 - Gets the flexible bytes + * @input: input stream to modify + * @flex_bytes: the flexible bytes to load + **/ +s32 ixgbe_atr_get_flex_byte_82599(struct ixgbe_atr_input *input, u16 *flex_byte) +{ + *flex_byte = input->byte_stream[IXGBE_ATR_FLEX_BYTE_OFFSET]; + *flex_byte |= input->byte_stream[IXGBE_ATR_FLEX_BYTE_OFFSET + 1] << 8; + + return 0; +} + +/** + * ixgbe_atr_get_vm_pool_82599 - Gets the Virtual Machine pool + * @input: input stream to modify + * @vm_pool: the Virtual Machine pool to load + **/ +s32 ixgbe_atr_get_vm_pool_82599(struct ixgbe_atr_input *input, u8 *vm_pool) +{ + *vm_pool = input->byte_stream[IXGBE_ATR_VM_POOL_OFFSET]; + + return 0; +} + +/** + * ixgbe_atr_get_l4type_82599 - Gets the layer 4 packet type + * @input: input stream to modify + * @l4type: the layer 4 type value to load + **/ +s32 ixgbe_atr_get_l4type_82599(struct ixgbe_atr_input *input, u8 *l4type) +{ + *l4type = input->byte_stream[IXGBE_ATR_L4TYPE_OFFSET]; + + return 0; +} + +/** + * ixgbe_atr_add_signature_filter_82599 - Adds a signature hash filter + * @hw: pointer to hardware structure + * @stream: input bitstream + * @queue: queue index to direct traffic to + **/ +s32 ixgbe_fdir_add_signature_filter_82599(struct ixgbe_hw *hw, + struct ixgbe_atr_input *input, + u8 queue) +{ + u64 fdirhashcmd; + u64 fdircmd; + u32 fdirhash; + u16 bucket_hash, sig_hash; + u8 l4type; + + bucket_hash = ixgbe_atr_compute_hash_82599(input, + IXGBE_ATR_BUCKET_HASH_KEY); + + /* bucket_hash is only 15 bits */ + bucket_hash &= IXGBE_ATR_HASH_MASK; + + sig_hash = ixgbe_atr_compute_hash_82599(input, + IXGBE_ATR_SIGNATURE_HASH_KEY); + + /* Get the l4type in order to program FDIRCMD properly */ + /* lowest 2 bits are FDIRCMD.L4TYPE, third lowest bit is FDIRCMD.IPV6 */ + ixgbe_atr_get_l4type_82599(input, &l4type); + + /* + * The lower 32-bits of fdirhashcmd is for FDIRHASH, the upper 32-bits + * is for FDIRCMD. Then do a 64-bit register write from FDIRHASH. + */ + fdirhash = sig_hash << IXGBE_FDIRHASH_SIG_SW_INDEX_SHIFT | bucket_hash; + + fdircmd = (IXGBE_FDIRCMD_CMD_ADD_FLOW | IXGBE_FDIRCMD_FILTER_UPDATE | + IXGBE_FDIRCMD_LAST | IXGBE_FDIRCMD_QUEUE_EN); + + switch (l4type & IXGBE_ATR_L4TYPE_MASK) { + case IXGBE_ATR_L4TYPE_TCP: + fdircmd |= IXGBE_FDIRCMD_L4TYPE_TCP; + break; + case IXGBE_ATR_L4TYPE_UDP: + fdircmd |= IXGBE_FDIRCMD_L4TYPE_UDP; + break; + case IXGBE_ATR_L4TYPE_SCTP: + fdircmd |= IXGBE_FDIRCMD_L4TYPE_SCTP; + break; + default: + hw_dbg(hw, "Error on l4type input\n"); + return IXGBE_ERR_CONFIG; + } + + if (l4type & IXGBE_ATR_L4TYPE_IPV6_MASK) + fdircmd |= IXGBE_FDIRCMD_IPV6; + + fdircmd |= ((u64)queue << IXGBE_FDIRCMD_RX_QUEUE_SHIFT); + fdirhashcmd = ((fdircmd << 32) | fdirhash); + + IXGBE_WRITE_REG64(hw, IXGBE_FDIRHASH, fdirhashcmd); + + return 0; +} + +/** + * ixgbe_fdir_add_perfect_filter_82599 - Adds a perfect filter + * @hw: pointer to hardware structure + * @input: input bitstream + * @queue: queue index to direct traffic to + * + * Note that the caller to this function must lock before calling, since the + * hardware writes must be protected from one another. + **/ +s32 ixgbe_fdir_add_perfect_filter_82599(struct ixgbe_hw *hw, + struct ixgbe_atr_input *input, + u16 soft_id, + u8 queue) +{ + u32 fdircmd = 0; + u32 fdirhash; + u32 src_ipv4, dst_ipv4; + u32 src_ipv6_1, src_ipv6_2, src_ipv6_3, src_ipv6_4; + u16 src_port, dst_port, vlan_id, flex_bytes; + u16 bucket_hash; + u8 l4type; + + /* Get our input values */ + ixgbe_atr_get_l4type_82599(input, &l4type); + + /* + * Check l4type formatting, and bail out before we touch the hardware + * if there's a configuration issue + */ + switch (l4type & IXGBE_ATR_L4TYPE_MASK) { + case IXGBE_ATR_L4TYPE_TCP: + fdircmd |= IXGBE_FDIRCMD_L4TYPE_TCP; + break; + case IXGBE_ATR_L4TYPE_UDP: + fdircmd |= IXGBE_FDIRCMD_L4TYPE_UDP; + break; + case IXGBE_ATR_L4TYPE_SCTP: + fdircmd |= IXGBE_FDIRCMD_L4TYPE_SCTP; + break; + default: + hw_dbg(hw, "Error on l4type input\n"); + return IXGBE_ERR_CONFIG; + } + + bucket_hash = ixgbe_atr_compute_hash_82599(input, + IXGBE_ATR_BUCKET_HASH_KEY); + + /* bucket_hash is only 15 bits */ + bucket_hash &= IXGBE_ATR_HASH_MASK; + + ixgbe_atr_get_vlan_id_82599(input, &vlan_id); + ixgbe_atr_get_src_port_82599(input, &src_port); + ixgbe_atr_get_dst_port_82599(input, &dst_port); + ixgbe_atr_get_flex_byte_82599(input, &flex_bytes); + + fdirhash = soft_id << IXGBE_FDIRHASH_SIG_SW_INDEX_SHIFT | bucket_hash; + + /* Now figure out if we're IPv4 or IPv6 */ + if (l4type & IXGBE_ATR_L4TYPE_IPV6_MASK) { + /* IPv6 */ + ixgbe_atr_get_src_ipv6_82599(input, &src_ipv6_1, &src_ipv6_2, + &src_ipv6_3, &src_ipv6_4); + + IXGBE_WRITE_REG(hw, IXGBE_FDIRSIPv6(0), src_ipv6_1); + IXGBE_WRITE_REG(hw, IXGBE_FDIRSIPv6(1), src_ipv6_2); + IXGBE_WRITE_REG(hw, IXGBE_FDIRSIPv6(2), src_ipv6_3); + /* The last 4 bytes is the same register as IPv4 */ + IXGBE_WRITE_REG(hw, IXGBE_FDIRIPSA, src_ipv6_4); + + fdircmd |= IXGBE_FDIRCMD_IPV6; + fdircmd |= IXGBE_FDIRCMD_IPv6DMATCH; + } else { + /* IPv4 */ + ixgbe_atr_get_src_ipv4_82599(input, &src_ipv4); + IXGBE_WRITE_REG(hw, IXGBE_FDIRIPSA, src_ipv4); + + } + + ixgbe_atr_get_dst_ipv4_82599(input, &dst_ipv4); + IXGBE_WRITE_REG(hw, IXGBE_FDIRIPDA, dst_ipv4); + + IXGBE_WRITE_REG(hw, IXGBE_FDIRVLAN, (vlan_id | + (flex_bytes << IXGBE_FDIRVLAN_FLEX_SHIFT))); + IXGBE_WRITE_REG(hw, IXGBE_FDIRPORT, (src_port | + (dst_port << IXGBE_FDIRPORT_DESTINATION_SHIFT))); + + fdircmd |= IXGBE_FDIRCMD_CMD_ADD_FLOW; + fdircmd |= IXGBE_FDIRCMD_FILTER_UPDATE; + fdircmd |= IXGBE_FDIRCMD_LAST; + fdircmd |= IXGBE_FDIRCMD_QUEUE_EN; + fdircmd |= queue << IXGBE_FDIRCMD_RX_QUEUE_SHIFT; + + IXGBE_WRITE_REG(hw, IXGBE_FDIRHASH, fdirhash); + IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD, fdircmd); + + return 0; +} +/** * ixgbe_read_analog_reg8_82599 - Reads 8 bit Omer analog register * @hw: pointer to hardware structure * @reg: analog register to read @@ -1056,8 +2142,9 @@ s32 ixgbe_write_analog_reg8_82599(struct ixgbe_hw *hw, u32 reg, u8 val) s32 ixgbe_start_hw_82599(struct ixgbe_hw *hw) { u32 q_num; + s32 ret_val; - ixgbe_start_hw_generic(hw); + ret_val = ixgbe_start_hw_generic(hw); /* Clear the rate limiters */ for (q_num = 0; q_num < hw->mac.max_tx_queues; q_num++) { @@ -1066,7 +2153,13 @@ s32 ixgbe_start_hw_82599(struct ixgbe_hw *hw) } IXGBE_WRITE_FLUSH(hw); - return 0; + /* We need to run link autotry after the driver loads */ + hw->mac.autotry_restart = true; + + if (ret_val == 0) + ret_val = ixgbe_verify_fw_version_82599(hw); + + return ret_val; } /** @@ -1093,53 +2186,100 @@ s32 ixgbe_identify_phy_82599(struct ixgbe_hw *hw) u32 ixgbe_get_supported_physical_layer_82599(struct ixgbe_hw *hw) { u32 physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN; + u32 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC); + u32 autoc2 = IXGBE_READ_REG(hw, IXGBE_AUTOC2); + u32 pma_pmd_10g_serial = autoc2 & IXGBE_AUTOC2_10G_SERIAL_PMA_PMD_MASK; + u32 pma_pmd_10g_parallel = autoc & IXGBE_AUTOC_10G_PMA_PMD_MASK; + u32 pma_pmd_1g = autoc & IXGBE_AUTOC_1G_PMA_PMD_MASK; + u16 ext_ability = 0; u8 comp_codes_10g = 0; - switch (hw->device_id) { - case IXGBE_DEV_ID_82599: - case IXGBE_DEV_ID_82599_KX4: - /* Default device ID is mezzanine card KX/KX4 */ - physical_layer = (IXGBE_PHYSICAL_LAYER_10GBASE_KX4 | - IXGBE_PHYSICAL_LAYER_1000BASE_KX); + hw->phy.ops.identify(hw); + + if (hw->phy.type == ixgbe_phy_tn || + hw->phy.type == ixgbe_phy_cu_unknown) { + hw->phy.ops.read_reg(hw, MDIO_PMA_EXTABLE, MDIO_MMD_PMAPMD, + &ext_ability); + if (ext_ability & MDIO_PMA_EXTABLE_10GBT) + physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_T; + if (ext_ability & MDIO_PMA_EXTABLE_1000BT) + physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T; + if (ext_ability & MDIO_PMA_EXTABLE_100BTX) + physical_layer |= IXGBE_PHYSICAL_LAYER_100BASE_TX; + goto out; + } + + switch (autoc & IXGBE_AUTOC_LMS_MASK) { + case IXGBE_AUTOC_LMS_1G_AN: + case IXGBE_AUTOC_LMS_1G_LINK_NO_AN: + if (pma_pmd_1g == IXGBE_AUTOC_1G_KX_BX) { + physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_KX | + IXGBE_PHYSICAL_LAYER_1000BASE_BX; + goto out; + } else + /* SFI mode so read SFP module */ + goto sfp_check; break; - case IXGBE_DEV_ID_82599_SFP: - hw->phy.ops.identify_sfp(hw); + case IXGBE_AUTOC_LMS_10G_LINK_NO_AN: + if (pma_pmd_10g_parallel == IXGBE_AUTOC_10G_CX4) + physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_CX4; + else if (pma_pmd_10g_parallel == IXGBE_AUTOC_10G_KX4) + physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KX4; + else if (pma_pmd_10g_parallel == IXGBE_AUTOC_10G_XAUI) + physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_XAUI; + goto out; + break; + case IXGBE_AUTOC_LMS_10G_SERIAL: + if (pma_pmd_10g_serial == IXGBE_AUTOC2_10G_KR) { + physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KR; + goto out; + } else if (pma_pmd_10g_serial == IXGBE_AUTOC2_10G_SFI) + goto sfp_check; + break; + case IXGBE_AUTOC_LMS_KX4_KX_KR: + case IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN: + if (autoc & IXGBE_AUTOC_KX_SUPP) + physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_KX; + if (autoc & IXGBE_AUTOC_KX4_SUPP) + physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_KX4; + if (autoc & IXGBE_AUTOC_KR_SUPP) + physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_KR; + goto out; + break; + default: + goto out; + break; + } - switch (hw->phy.sfp_type) { - case ixgbe_sfp_type_da_cu: - case ixgbe_sfp_type_da_cu_core0: - case ixgbe_sfp_type_da_cu_core1: - physical_layer = IXGBE_PHYSICAL_LAYER_SFP_PLUS_CU; - break; - case ixgbe_sfp_type_sr: +sfp_check: + /* SFP check must be done last since DA modules are sometimes used to + * test KR mode - we need to id KR mode correctly before SFP module. + * Call identify_sfp because the pluggable module may have changed */ + hw->phy.ops.identify_sfp(hw); + if (hw->phy.sfp_type == ixgbe_sfp_type_not_present) + goto out; + + switch (hw->phy.type) { + case ixgbe_phy_tw_tyco: + case ixgbe_phy_tw_unknown: + physical_layer = IXGBE_PHYSICAL_LAYER_SFP_PLUS_CU; + break; + case ixgbe_phy_sfp_avago: + case ixgbe_phy_sfp_ftl: + case ixgbe_phy_sfp_intel: + case ixgbe_phy_sfp_unknown: + hw->phy.ops.read_i2c_eeprom(hw, + IXGBE_SFF_10GBE_COMP_CODES, &comp_codes_10g); + if (comp_codes_10g & IXGBE_SFF_10GBASESR_CAPABLE) physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_SR; - break; - case ixgbe_sfp_type_lr: + else if (comp_codes_10g & IXGBE_SFF_10GBASELR_CAPABLE) physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_LR; - break; - case ixgbe_sfp_type_srlr_core0: - case ixgbe_sfp_type_srlr_core1: - hw->phy.ops.read_i2c_eeprom(hw, - IXGBE_SFF_10GBE_COMP_CODES, - &comp_codes_10g); - if (comp_codes_10g & IXGBE_SFF_10GBASESR_CAPABLE) - physical_layer = - IXGBE_PHYSICAL_LAYER_10GBASE_SR; - else if (comp_codes_10g & IXGBE_SFF_10GBASELR_CAPABLE) - physical_layer = - IXGBE_PHYSICAL_LAYER_10GBASE_LR; - else - physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN; - default: - physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN; - break; - } break; default: - physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN; break; } +out: return physical_layer; } @@ -1187,6 +2327,138 @@ s32 ixgbe_enable_rx_dma_82599(struct ixgbe_hw *hw, u32 regval) return 0; } +/** + * ixgbe_get_device_caps_82599 - Get additional device capabilities + * @hw: pointer to hardware structure + * @device_caps: the EEPROM word with the extra device capabilities + * + * This function will read the EEPROM location for the device capabilities, + * and return the word through device_caps. + **/ +s32 ixgbe_get_device_caps_82599(struct ixgbe_hw *hw, u16 *device_caps) +{ + hw->eeprom.ops.read(hw, IXGBE_DEVICE_CAPS, device_caps); + + return 0; +} + +/** + * ixgbe_get_san_mac_addr_offset_82599 - SAN MAC address offset for 82599 + * @hw: pointer to hardware structure + * @san_mac_offset: SAN MAC address offset + * + * This function will read the EEPROM location for the SAN MAC address + * pointer, and returns the value at that location. This is used in both + * get and set mac_addr routines. + **/ +s32 ixgbe_get_san_mac_addr_offset_82599(struct ixgbe_hw *hw, + u16 *san_mac_offset) +{ + /* + * First read the EEPROM pointer to see if the MAC addresses are + * available. + */ + hw->eeprom.ops.read(hw, IXGBE_SAN_MAC_ADDR_PTR, san_mac_offset); + + return 0; +} + +/** + * ixgbe_get_san_mac_addr_82599 - SAN MAC address retrieval for 82599 + * @hw: pointer to hardware structure + * @san_mac_addr: SAN MAC address + * + * Reads the SAN MAC address from the EEPROM, if it's available. This is + * per-port, so set_lan_id() must be called before reading the addresses. + * set_lan_id() is called by identify_sfp(), but this cannot be relied + * upon for non-SFP connections, so we must call it here. + **/ +s32 ixgbe_get_san_mac_addr_82599(struct ixgbe_hw *hw, u8 *san_mac_addr) +{ + u16 san_mac_data, san_mac_offset; + u8 i; + + /* + * First read the EEPROM pointer to see if the MAC addresses are + * available. If they're not, no point in calling set_lan_id() here. + */ + ixgbe_get_san_mac_addr_offset_82599(hw, &san_mac_offset); + + if ((san_mac_offset == 0) || (san_mac_offset == 0xFFFF)) { + /* + * No addresses available in this EEPROM. It's not an + * error though, so just wipe the local address and return. + */ + for (i = 0; i < 6; i++) + san_mac_addr[i] = 0xFF; + + goto san_mac_addr_out; + } + + /* make sure we know which port we need to program */ + hw->mac.ops.set_lan_id(hw); + /* apply the port offset to the address offset */ + (hw->bus.func) ? (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT1_OFFSET) : + (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT0_OFFSET); + for (i = 0; i < 3; i++) { + hw->eeprom.ops.read(hw, san_mac_offset, &san_mac_data); + san_mac_addr[i * 2] = (u8)(san_mac_data); + san_mac_addr[i * 2 + 1] = (u8)(san_mac_data >> 8); + san_mac_offset++; + } + +san_mac_addr_out: + return 0; +} + +/** + * ixgbe_verify_fw_version_82599 - verify fw version for 82599 + * @hw: pointer to hardware structure + * + * Verifies that installed the firmware version is 0.6 or higher + * for SFI devices. All 82599 SFI devices should have version 0.6 or higher. + * + * Returns IXGBE_ERR_EEPROM_VERSION if the FW is not present or + * if the FW version is not supported. + **/ +static s32 ixgbe_verify_fw_version_82599(struct ixgbe_hw *hw) +{ + s32 status = IXGBE_ERR_EEPROM_VERSION; + u16 fw_offset, fw_ptp_cfg_offset; + u16 fw_version = 0; + + /* firmware check is only necessary for SFI devices */ + if (hw->phy.media_type != ixgbe_media_type_fiber) { + status = 0; + goto fw_version_out; + } + + /* get the offset to the Firmware Module block */ + hw->eeprom.ops.read(hw, IXGBE_FW_PTR, &fw_offset); + + if ((fw_offset == 0) || (fw_offset == 0xFFFF)) + goto fw_version_out; + + /* get the offset to the Pass Through Patch Configuration block */ + hw->eeprom.ops.read(hw, (fw_offset + + IXGBE_FW_PASSTHROUGH_PATCH_CONFIG_PTR), + &fw_ptp_cfg_offset); + + if ((fw_ptp_cfg_offset == 0) || (fw_ptp_cfg_offset == 0xFFFF)) + goto fw_version_out; + + /* get the firmware version */ + hw->eeprom.ops.read(hw, (fw_ptp_cfg_offset + + IXGBE_FW_PATCH_VERSION_4), + &fw_version); + + if (fw_version > 0x5) + status = 0; + +fw_version_out: + return status; +} + static struct ixgbe_mac_operations mac_ops_82599 = { .init_hw = &ixgbe_init_hw_generic, .reset_hw = &ixgbe_reset_hw_82599, @@ -1196,6 +2468,8 @@ static struct ixgbe_mac_operations mac_ops_82599 = { .get_supported_physical_layer = &ixgbe_get_supported_physical_layer_82599, .enable_rx_dma = &ixgbe_enable_rx_dma_82599, .get_mac_addr = &ixgbe_get_mac_addr_generic, + .get_san_mac_addr = &ixgbe_get_san_mac_addr_82599, + .get_device_caps = &ixgbe_get_device_caps_82599, .stop_adapter = &ixgbe_stop_adapter_generic, .get_bus_info = &ixgbe_get_bus_info_generic, .set_lan_id = &ixgbe_set_lan_id_multi_port_pcie, @@ -1220,7 +2494,7 @@ static struct ixgbe_mac_operations mac_ops_82599 = { .disable_mc = &ixgbe_disable_mc_generic, .clear_vfta = &ixgbe_clear_vfta_82599, .set_vfta = &ixgbe_set_vfta_82599, - .setup_fc = &ixgbe_setup_fc_generic, + .fc_enable = &ixgbe_fc_enable_generic, .init_uta_tables = &ixgbe_init_uta_tables_82599, .setup_sfp = &ixgbe_setup_sfp_modules_82599, }; @@ -1236,6 +2510,7 @@ static struct ixgbe_eeprom_operations eeprom_ops_82599 = { static struct ixgbe_phy_operations phy_ops_82599 = { .identify = &ixgbe_identify_phy_82599, .identify_sfp = &ixgbe_identify_sfp_module_generic, + .init = &ixgbe_init_phy_ops_82599, .reset = &ixgbe_reset_phy_generic, .read_reg = &ixgbe_read_phy_reg_generic, .write_reg = &ixgbe_write_phy_reg_generic, |