diff options
Diffstat (limited to 'drivers/net/ethernet/stmicro/stmmac/Kconfig')
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/Kconfig | 72 |
1 files changed, 6 insertions, 66 deletions
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig index b02d4a3ffa37..7d3af190be55 100644 --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig @@ -14,62 +14,20 @@ config STMMAC_ETH if STMMAC_ETH config STMMAC_PLATFORM - bool "STMMAC Platform bus support" + tristate "STMMAC Platform bus support" depends on STMMAC_ETH default y ---help--- - This selects the platform specific bus support for - the stmmac device driver. This is the driver used - on many embedded STM platforms based on ARM and SuperH - processors. + This selects the platform specific bus support for the stmmac driver. + This is the driver used on several SoCs: + STi, Allwinner, Amlogic Meson, Altera SOCFPGA. + If you have a controller with this interface, say Y or M here. If unsure, say N. -config DWMAC_MESON - bool "Amlogic Meson dwmac support" - depends on STMMAC_PLATFORM && ARCH_MESON - help - Support for Ethernet controller on Amlogic Meson SoCs. - - This selects the Amlogic Meson SoC glue layer support for - the stmmac device driver. This driver is used for Meson6 and - Meson8 SoCs. - -config DWMAC_SOCFPGA - bool "SOCFPGA dwmac support" - depends on STMMAC_PLATFORM && MFD_SYSCON && (ARCH_SOCFPGA || COMPILE_TEST) - help - Support for ethernet controller on Altera SOCFPGA - - This selects the Altera SOCFPGA SoC glue layer support - for the stmmac device driver. This driver is used for - arria5 and cyclone5 FPGA SoCs. - -config DWMAC_SUNXI - bool "Allwinner GMAC support" - depends on STMMAC_PLATFORM && ARCH_SUNXI - default y - ---help--- - Support for Allwinner A20/A31 GMAC ethernet controllers. - - This selects Allwinner SoC glue layer support for the - stmmac device driver. This driver is used for A20/A31 - GMAC ethernet controller. - -config DWMAC_STI - bool "STi GMAC support" - depends on STMMAC_PLATFORM && ARCH_STI - default y - ---help--- - Support for ethernet controller on STi SOCs. - - This selects STi SoC glue layer support for the stmmac - device driver. This driver is used on for the STi series - SOCs GMAC ethernet controller. - config STMMAC_PCI - bool "STMMAC PCI bus support" + tristate "STMMAC PCI bus support" depends on STMMAC_ETH && PCI ---help--- This is to select the Synopsys DWMAC available on PCI devices, @@ -79,22 +37,4 @@ config STMMAC_PCI D1215994A VIRTEX FPGA board. If unsure, say N. - -config STMMAC_DEBUG_FS - bool "Enable monitoring via sysFS " - default n - depends on STMMAC_ETH && DEBUG_FS - ---help--- - The stmmac entry in /sys reports DMA TX/RX rings - or (if supported) the HW cap register. - -config STMMAC_DA - bool "STMMAC DMA arbitration scheme" - default n - ---help--- - Selecting this option, rx has priority over Tx (only for Giga - Ethernet device). - By default, the DMA arbitration scheme is based on Round-robin - (rx:tx priority is 1:1). - endif |