diff options
Diffstat (limited to 'drivers/mtd/nand')
26 files changed, 2860 insertions, 235 deletions
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index 20f01b3ec23d..f05e0e9eb2f7 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -74,6 +74,7 @@ config MTD_NAND_DENALI_SCRATCH_REG_ADDR config MTD_NAND_GPIO tristate "GPIO assisted NAND Flash driver" depends on GPIOLIB || COMPILE_TEST + depends on HAS_IOMEM help This enables a NAND flash driver where control signals are connected to GPIO pins, and commands and data are communicated @@ -310,6 +311,7 @@ config MTD_NAND_CAFE config MTD_NAND_CS553X tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)" depends on X86_32 + depends on !UML && HAS_IOMEM help The CS553x companion chips for the AMD Geode processor include NAND flash controllers with built-in hardware ECC @@ -463,6 +465,7 @@ config MTD_NAND_MPC5121_NFC config MTD_NAND_VF610_NFC tristate "Support for Freescale NFC for VF610/MPC5125" depends on (SOC_VF610 || COMPILE_TEST) + depends on HAS_IOMEM help Enables support for NAND Flash Controller on some Freescale processors like the VF610, MPC5125, MCF54418 or Kinetis K70. @@ -553,4 +556,11 @@ config MTD_NAND_HISI504 help Enables support for NAND controller on Hisilicon SoC Hip04. +config MTD_NAND_QCOM + tristate "Support for NAND on QCOM SoCs" + depends on ARCH_QCOM + help + Enables support for NAND flash chips on SoCs containing the EBI2 NAND + controller. This controller is found on IPQ806x SoC. + endif # MTD_NAND diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile index 9e3623308509..f55335373f7c 100644 --- a/drivers/mtd/nand/Makefile +++ b/drivers/mtd/nand/Makefile @@ -56,5 +56,6 @@ obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH) += bcm47xxnflash/ obj-$(CONFIG_MTD_NAND_SUNXI) += sunxi_nand.o obj-$(CONFIG_MTD_NAND_HISI504) += hisi504_nand.o obj-$(CONFIG_MTD_NAND_BRCMNAND) += brcmnand/ +obj-$(CONFIG_MTD_NAND_QCOM) += qcom_nandc.o nand-objs := nand_base.o nand_bbt.o nand_timings.o diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c index bddcf83d6859..20cbaabb2959 100644 --- a/drivers/mtd/nand/atmel_nand.c +++ b/drivers/mtd/nand/atmel_nand.c @@ -65,6 +65,11 @@ module_param(on_flash_bbt, int, 0); struct atmel_nand_caps { bool pmecc_correct_erase_page; + uint8_t pmecc_max_correction; +}; + +struct atmel_nand_nfc_caps { + uint32_t rb_mask; }; /* oob layout for large page size @@ -111,6 +116,7 @@ struct atmel_nfc { /* Point to the sram bank which include readed data via NFC */ void *data_in_sram; bool will_write_sram; + const struct atmel_nand_nfc_caps *caps; }; static struct atmel_nfc nand_nfc; @@ -140,6 +146,7 @@ struct atmel_nand_host { int pmecc_cw_len; /* Length of codeword */ void __iomem *pmerrloc_base; + void __iomem *pmerrloc_el_base; void __iomem *pmecc_rom_base; /* lookup table for alpha_to and index_of */ @@ -468,6 +475,7 @@ static void atmel_write_buf(struct mtd_info *mtd, const u8 *buf, int len) * 8-bits 13-bytes 14-bytes * 12-bits 20-bytes 21-bytes * 24-bits 39-bytes 42-bytes + * 32-bits 52-bytes 56-bytes */ static int pmecc_get_ecc_bytes(int cap, int sector_size) { @@ -813,7 +821,7 @@ static void pmecc_correct_data(struct mtd_info *mtd, uint8_t *buf, uint8_t *ecc, sector_size = host->pmecc_sector_size; while (err_nbr) { - tmp = pmerrloc_readl_el_relaxed(host->pmerrloc_base, i) - 1; + tmp = pmerrloc_readl_el_relaxed(host->pmerrloc_el_base, i) - 1; byte_pos = tmp / 8; bit_pos = tmp % 8; @@ -825,7 +833,7 @@ static void pmecc_correct_data(struct mtd_info *mtd, uint8_t *buf, uint8_t *ecc, *(buf + byte_pos) ^= (1 << bit_pos); pos = sector_num * host->pmecc_sector_size + byte_pos; - dev_info(host->dev, "Bit flip in data area, byte_pos: %d, bit_pos: %d, 0x%02x -> 0x%02x\n", + dev_dbg(host->dev, "Bit flip in data area, byte_pos: %d, bit_pos: %d, 0x%02x -> 0x%02x\n", pos, bit_pos, err_byte, *(buf + byte_pos)); } else { /* Bit flip in OOB area */ @@ -835,7 +843,7 @@ static void pmecc_correct_data(struct mtd_info *mtd, uint8_t *buf, uint8_t *ecc, ecc[tmp] ^= (1 << bit_pos); pos = tmp + nand_chip->ecc.layout->eccpos[0]; - dev_info(host->dev, "Bit flip in OOB, oob_byte_pos: %d, bit_pos: %d, 0x%02x -> 0x%02x\n", + dev_dbg(host->dev, "Bit flip in OOB, oob_byte_pos: %d, bit_pos: %d, 0x%02x -> 0x%02x\n", pos, bit_pos, err_byte, ecc[tmp]); } @@ -1017,6 +1025,9 @@ static void atmel_pmecc_core_init(struct mtd_info *mtd) case 24: val = PMECC_CFG_BCH_ERR24; break; + case 32: + val = PMECC_CFG_BCH_ERR32; + break; } if (host->pmecc_sector_size == 512) @@ -1078,6 +1089,9 @@ static int pmecc_choose_ecc(struct atmel_nand_host *host, /* If device tree doesn't specify, use NAND's minimum ECC parameters */ if (host->pmecc_corr_cap == 0) { + if (*cap > host->caps->pmecc_max_correction) + return -EINVAL; + /* use the most fitable ecc bits (the near bigger one ) */ if (*cap <= 2) host->pmecc_corr_cap = 2; @@ -1089,6 +1103,8 @@ static int pmecc_choose_ecc(struct atmel_nand_host *host, host->pmecc_corr_cap = 12; else if (*cap <= 24) host->pmecc_corr_cap = 24; + else if (*cap <= 32) + host->pmecc_corr_cap = 32; else return -EINVAL; } @@ -1205,6 +1221,8 @@ static int atmel_pmecc_nand_init_params(struct platform_device *pdev, err_no = PTR_ERR(host->pmerrloc_base); goto err; } + host->pmerrloc_el_base = host->pmerrloc_base + ATMEL_PMERRLOC_SIGMAx + + (host->caps->pmecc_max_correction + 1) * 4; if (!host->has_no_lookup_table) { regs_rom = platform_get_resource(pdev, IORESOURCE_MEM, 3); @@ -1486,8 +1504,6 @@ static void atmel_nand_hwctl(struct mtd_info *mtd, int mode) ecc_writel(host->ecc, CR, ATMEL_ECC_RST); } -static const struct of_device_id atmel_nand_dt_ids[]; - static int atmel_of_init_port(struct atmel_nand_host *host, struct device_node *np) { @@ -1498,7 +1514,7 @@ static int atmel_of_init_port(struct atmel_nand_host *host, enum of_gpio_flags flags = 0; host->caps = (struct atmel_nand_caps *) - of_match_device(atmel_nand_dt_ids, host->dev)->data; + of_device_get_match_data(host->dev); if (of_property_read_u32(np, "atmel,nand-addr-offset", &val) == 0) { if (val >= 32) { @@ -1547,10 +1563,16 @@ static int atmel_of_init_port(struct atmel_nand_host *host, * them from NAND ONFI parameters. */ if (of_property_read_u32(np, "atmel,pmecc-cap", &val) == 0) { - if ((val != 2) && (val != 4) && (val != 8) && (val != 12) && - (val != 24)) { + if (val > host->caps->pmecc_max_correction) { dev_err(host->dev, - "Unsupported PMECC correction capability: %d; should be 2, 4, 8, 12 or 24\n", + "Required ECC strength too high: %u max %u\n", + val, host->caps->pmecc_max_correction); + return -EINVAL; + } + if ((val != 2) && (val != 4) && (val != 8) && + (val != 12) && (val != 24) && (val != 32)) { + dev_err(host->dev, + "Required ECC strength not supported: %u\n", val); return -EINVAL; } @@ -1560,7 +1582,7 @@ static int atmel_of_init_port(struct atmel_nand_host *host, if (of_property_read_u32(np, "atmel,pmecc-sector-size", &val) == 0) { if ((val != 512) && (val != 1024)) { dev_err(host->dev, - "Unsupported PMECC sector size: %d; should be 512 or 1024 bytes\n", + "Required ECC sector size not supported: %u\n", val); return -EINVAL; } @@ -1677,9 +1699,9 @@ static irqreturn_t hsmc_interrupt(int irq, void *dev_id) nfc_writel(host->nfc->hsmc_regs, IDR, NFC_SR_XFR_DONE); ret = IRQ_HANDLED; } - if (pending & NFC_SR_RB_EDGE) { + if (pending & host->nfc->caps->rb_mask) { complete(&host->nfc->comp_ready); - nfc_writel(host->nfc->hsmc_regs, IDR, NFC_SR_RB_EDGE); + nfc_writel(host->nfc->hsmc_regs, IDR, host->nfc->caps->rb_mask); ret = IRQ_HANDLED; } if (pending & NFC_SR_CMD_DONE) { @@ -1697,7 +1719,7 @@ static void nfc_prepare_interrupt(struct atmel_nand_host *host, u32 flag) if (flag & NFC_SR_XFR_DONE) init_completion(&host->nfc->comp_xfer_done); - if (flag & NFC_SR_RB_EDGE) + if (flag & host->nfc->caps->rb_mask) init_completion(&host->nfc->comp_ready); if (flag & NFC_SR_CMD_DONE) @@ -1715,7 +1737,7 @@ static int nfc_wait_interrupt(struct atmel_nand_host *host, u32 flag) if (flag & NFC_SR_XFR_DONE) comp[index++] = &host->nfc->comp_xfer_done; - if (flag & NFC_SR_RB_EDGE) + if (flag & host->nfc->caps->rb_mask) comp[index++] = &host->nfc->comp_ready; if (flag & NFC_SR_CMD_DONE) @@ -1783,7 +1805,7 @@ static int nfc_device_ready(struct mtd_info *mtd) dev_err(host->dev, "Lost the interrupt flags: 0x%08x\n", mask & status); - return status & NFC_SR_RB_EDGE; + return status & host->nfc->caps->rb_mask; } static void nfc_select_chip(struct mtd_info *mtd, int chip) @@ -1956,8 +1978,8 @@ static void nfc_nand_command(struct mtd_info *mtd, unsigned int command, } /* fall through */ default: - nfc_prepare_interrupt(host, NFC_SR_RB_EDGE); - nfc_wait_interrupt(host, NFC_SR_RB_EDGE); + nfc_prepare_interrupt(host, host->nfc->caps->rb_mask); + nfc_wait_interrupt(host, host->nfc->caps->rb_mask); } } @@ -2304,17 +2326,34 @@ static int atmel_nand_remove(struct platform_device *pdev) return 0; } +/* + * AT91RM9200 does not have PMECC or PMECC Errloc peripherals for + * BCH ECC. Combined with the "atmel,has-pmecc", it is used to describe + * devices from the SAM9 family that have those. + */ static const struct atmel_nand_caps at91rm9200_caps = { .pmecc_correct_erase_page = false, + .pmecc_max_correction = 24, }; static const struct atmel_nand_caps sama5d4_caps = { .pmecc_correct_erase_page = true, + .pmecc_max_correction = 24, +}; + +/* + * The PMECC Errloc controller starting in SAMA5D2 is not compatible, + * as the increased correction strength requires more registers. + */ +static const struct atmel_nand_caps sama5d2_caps = { + .pmecc_correct_erase_page = true, + .pmecc_max_correction = 32, }; static const struct of_device_id atmel_nand_dt_ids[] = { { .compatible = "atmel,at91rm9200-nand", .data = &at91rm9200_caps }, { .compatible = "atmel,sama5d4-nand", .data = &sama5d4_caps }, + { .compatible = "atmel,sama5d2-nand", .data = &sama5d2_caps }, { /* sentinel */ } }; @@ -2354,6 +2393,11 @@ static int atmel_nand_nfc_probe(struct platform_device *pdev) } } + nfc->caps = (const struct atmel_nand_nfc_caps *) + of_device_get_match_data(&pdev->dev); + if (!nfc->caps) + return -ENODEV; + nfc_writel(nfc->hsmc_regs, IDR, 0xffffffff); nfc_readl(nfc->hsmc_regs, SR); /* clear the NFC_SR */ @@ -2382,8 +2426,17 @@ static int atmel_nand_nfc_remove(struct platform_device *pdev) return 0; } +static const struct atmel_nand_nfc_caps sama5d3_nfc_caps = { + .rb_mask = NFC_SR_RB_EDGE0, +}; + +static const struct atmel_nand_nfc_caps sama5d4_nfc_caps = { + .rb_mask = NFC_SR_RB_EDGE3, +}; + static const struct of_device_id atmel_nand_nfc_match[] = { - { .compatible = "atmel,sama5d3-nfc" }, + { .compatible = "atmel,sama5d3-nfc", .data = &sama5d3_nfc_caps }, + { .compatible = "atmel,sama5d4-nfc", .data = &sama5d4_nfc_caps }, { /* sentinel */ } }; MODULE_DEVICE_TABLE(of, atmel_nand_nfc_match); diff --git a/drivers/mtd/nand/atmel_nand_ecc.h b/drivers/mtd/nand/atmel_nand_ecc.h index 668e7358f19b..834d694487bd 100644 --- a/drivers/mtd/nand/atmel_nand_ecc.h +++ b/drivers/mtd/nand/atmel_nand_ecc.h @@ -43,6 +43,7 @@ #define PMECC_CFG_BCH_ERR8 (2 << 0) #define PMECC_CFG_BCH_ERR12 (3 << 0) #define PMECC_CFG_BCH_ERR24 (4 << 0) +#define PMECC_CFG_BCH_ERR32 (5 << 0) #define PMECC_CFG_SECTOR512 (0 << 4) #define PMECC_CFG_SECTOR1024 (1 << 4) @@ -108,7 +109,11 @@ #define PMERRLOC_ERR_NUM_MASK (0x1f << 8) #define PMERRLOC_CALC_DONE (1 << 0) #define ATMEL_PMERRLOC_SIGMAx 0x028 /* Error location SIGMA x */ -#define ATMEL_PMERRLOC_ELx 0x08c /* Error location x */ + +/* + * The ATMEL_PMERRLOC_ELx register location depends from the number of + * bits corrected by the PMECC controller. Do not use it. + */ /* Register access macros for PMECC */ #define pmecc_readl_relaxed(addr, reg) \ @@ -136,7 +141,7 @@ readl_relaxed((addr) + ATMEL_PMERRLOC_SIGMAx + ((n) * 4)) #define pmerrloc_readl_el_relaxed(addr, n) \ - readl_relaxed((addr) + ATMEL_PMERRLOC_ELx + ((n) * 4)) + readl_relaxed((addr) + ((n) * 4)) /* Galois field dimension */ #define PMECC_GF_DIMENSION_13 13 diff --git a/drivers/mtd/nand/atmel_nand_nfc.h b/drivers/mtd/nand/atmel_nand_nfc.h index 4d5d26221a7e..0bbc1fa97dba 100644 --- a/drivers/mtd/nand/atmel_nand_nfc.h +++ b/drivers/mtd/nand/atmel_nand_nfc.h @@ -42,7 +42,8 @@ #define NFC_SR_UNDEF (1 << 21) #define NFC_SR_AWB (1 << 22) #define NFC_SR_ASE (1 << 23) -#define NFC_SR_RB_EDGE (1 << 24) +#define NFC_SR_RB_EDGE0 (1 << 24) +#define NFC_SR_RB_EDGE3 (1 << 27) #define ATMEL_HSMC_NFC_IER 0x0c #define ATMEL_HSMC_NFC_IDR 0x10 diff --git a/drivers/mtd/nand/brcmnand/brcmnand.c b/drivers/mtd/nand/brcmnand/brcmnand.c index 844fc07d22cd..e0528397306a 100644 --- a/drivers/mtd/nand/brcmnand/brcmnand.c +++ b/drivers/mtd/nand/brcmnand/brcmnand.c @@ -311,6 +311,36 @@ static const u16 brcmnand_regs_v60[] = { [BRCMNAND_FC_BASE] = 0x400, }; +/* BRCMNAND v7.1 */ +static const u16 brcmnand_regs_v71[] = { + [BRCMNAND_CMD_START] = 0x04, + [BRCMNAND_CMD_EXT_ADDRESS] = 0x08, + [BRCMNAND_CMD_ADDRESS] = 0x0c, + [BRCMNAND_INTFC_STATUS] = 0x14, + [BRCMNAND_CS_SELECT] = 0x18, + [BRCMNAND_CS_XOR] = 0x1c, + [BRCMNAND_LL_OP] = 0x20, + [BRCMNAND_CS0_BASE] = 0x50, + [BRCMNAND_CS1_BASE] = 0, + [BRCMNAND_CORR_THRESHOLD] = 0xdc, + [BRCMNAND_CORR_THRESHOLD_EXT] = 0xe0, + [BRCMNAND_UNCORR_COUNT] = 0xfc, + [BRCMNAND_CORR_COUNT] = 0x100, + [BRCMNAND_CORR_EXT_ADDR] = 0x10c, + [BRCMNAND_CORR_ADDR] = 0x110, + [BRCMNAND_UNCORR_EXT_ADDR] = 0x114, + [BRCMNAND_UNCORR_ADDR] = 0x118, + [BRCMNAND_SEMAPHORE] = 0x150, + [BRCMNAND_ID] = 0x194, + [BRCMNAND_ID_EXT] = 0x198, + [BRCMNAND_LL_RDATA] = 0x19c, + [BRCMNAND_OOB_READ_BASE] = 0x200, + [BRCMNAND_OOB_READ_10_BASE] = 0, + [BRCMNAND_OOB_WRITE_BASE] = 0x280, + [BRCMNAND_OOB_WRITE_10_BASE] = 0, + [BRCMNAND_FC_BASE] = 0x400, +}; + enum brcmnand_cs_reg { BRCMNAND_CS_CFG_EXT = 0, BRCMNAND_CS_CFG, @@ -406,7 +436,9 @@ static int brcmnand_revision_init(struct brcmnand_controller *ctrl) } /* Register offsets */ - if (ctrl->nand_version >= 0x0600) + if (ctrl->nand_version >= 0x0701) + ctrl->reg_offsets = brcmnand_regs_v71; + else if (ctrl->nand_version >= 0x0600) ctrl->reg_offsets = brcmnand_regs_v60; else if (ctrl->nand_version >= 0x0500) ctrl->reg_offsets = brcmnand_regs_v50; @@ -796,7 +828,8 @@ static struct nand_ecclayout *brcmnand_create_layout(int ecc_level, idx2 >= MTD_MAX_OOBFREE_ENTRIES_LARGE - 1) break; } - goto out; + + return layout; } /* @@ -847,10 +880,7 @@ static struct nand_ecclayout *brcmnand_create_layout(int ecc_level, idx2 >= MTD_MAX_OOBFREE_ENTRIES_LARGE - 1) break; } -out: - /* Sum available OOB */ - for (i = 0; i < MTD_MAX_OOBFREE_ENTRIES_LARGE; i++) - layout->oobavail += layout->oobfree[i].length; + return layout; } diff --git a/drivers/mtd/nand/cafe_nand.c b/drivers/mtd/nand/cafe_nand.c index aa1a616b9fb6..e553aff68987 100644 --- a/drivers/mtd/nand/cafe_nand.c +++ b/drivers/mtd/nand/cafe_nand.c @@ -537,7 +537,7 @@ static int cafe_nand_write_page_lowlevel(struct mtd_info *mtd, return 0; } -static int cafe_nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip) +static int cafe_nand_block_bad(struct mtd_info *mtd, loff_t ofs) { return 0; } diff --git a/drivers/mtd/nand/diskonchip.c b/drivers/mtd/nand/diskonchip.c index f170f3c31b34..547c1002941d 100644 --- a/drivers/mtd/nand/diskonchip.c +++ b/drivers/mtd/nand/diskonchip.c @@ -794,7 +794,7 @@ static int doc200x_dev_ready(struct mtd_info *mtd) } } -static int doc200x_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip) +static int doc200x_block_bad(struct mtd_info *mtd, loff_t ofs) { /* This is our last resort if we couldn't find or create a BBT. Just pretend all blocks are good. */ diff --git a/drivers/mtd/nand/docg4.c b/drivers/mtd/nand/docg4.c index df4165b02c62..d86a60e1bbcb 100644 --- a/drivers/mtd/nand/docg4.c +++ b/drivers/mtd/nand/docg4.c @@ -225,7 +225,6 @@ struct docg4_priv { static struct nand_ecclayout docg4_oobinfo = { .eccbytes = 9, .eccpos = {7, 8, 9, 10, 11, 12, 13, 14, 15}, - .oobavail = 5, .oobfree = { {.offset = 2, .length = 5} } }; @@ -1121,7 +1120,7 @@ static int docg4_block_markbad(struct mtd_info *mtd, loff_t ofs) return ret; } -static int docg4_block_neverbad(struct mtd_info *mtd, loff_t ofs, int getchip) +static int docg4_block_neverbad(struct mtd_info *mtd, loff_t ofs) { /* only called when module_param ignore_badblocks is set */ return 0; diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c index 235ddcb58f39..8122c699ccf2 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c @@ -1,7 +1,7 @@ /* * Freescale GPMI NAND Flash Driver * - * Copyright (C) 2010-2011 Freescale Semiconductor, Inc. + * Copyright (C) 2010-2015 Freescale Semiconductor, Inc. * Copyright (C) 2008 Embedded Alley Solutions, Inc. * * This program is free software; you can redistribute it and/or modify @@ -136,7 +136,7 @@ static inline bool gpmi_check_ecc(struct gpmi_nand_data *this) * * We may have available oob space in this case. */ -static bool set_geometry_by_ecc_info(struct gpmi_nand_data *this) +static int set_geometry_by_ecc_info(struct gpmi_nand_data *this) { struct bch_geometry *geo = &this->bch_geometry; struct nand_chip *chip = &this->nand; @@ -145,7 +145,7 @@ static bool set_geometry_by_ecc_info(struct gpmi_nand_data *this) unsigned int block_mark_bit_offset; if (!(chip->ecc_strength_ds > 0 && chip->ecc_step_ds > 0)) - return false; + return -EINVAL; switch (chip->ecc_step_ds) { case SZ_512: @@ -158,19 +158,19 @@ static bool set_geometry_by_ecc_info(struct gpmi_nand_data *this) dev_err(this->dev, "unsupported nand chip. ecc bits : %d, ecc size : %d\n", chip->ecc_strength_ds, chip->ecc_step_ds); - return false; + return -EINVAL; } geo->ecc_chunk_size = chip->ecc_step_ds; geo->ecc_strength = round_up(chip->ecc_strength_ds, 2); if (!gpmi_check_ecc(this)) - return false; + return -EINVAL; /* Keep the C >= O */ if (geo->ecc_chunk_size < mtd->oobsize) { dev_err(this->dev, "unsupported nand chip. ecc size: %d, oob size : %d\n", chip->ecc_step_ds, mtd->oobsize); - return false; + return -EINVAL; } /* The default value, see comment in the legacy_set_geometry(). */ @@ -242,7 +242,7 @@ static bool set_geometry_by_ecc_info(struct gpmi_nand_data *this) + ALIGN(geo->ecc_chunk_count, 4); if (!this->swap_block_mark) - return true; + return 0; /* For bit swap. */ block_mark_bit_offset = mtd->writesize * 8 - @@ -251,7 +251,7 @@ static bool set_geometry_by_ecc_info(struct gpmi_nand_data *this) geo->block_mark_byte_offset = block_mark_bit_offset / 8; geo->block_mark_bit_offset = block_mark_bit_offset % 8; - return true; + return 0; } static int legacy_set_geometry(struct gpmi_nand_data *this) @@ -285,7 +285,8 @@ static int legacy_set_geometry(struct gpmi_nand_data *this) geo->ecc_strength = get_ecc_strength(this); if (!gpmi_check_ecc(this)) { dev_err(this->dev, - "required ecc strength of the NAND chip: %d is not supported by the GPMI controller (%d)\n", + "ecc strength: %d cannot be supported by the controller (%d)\n" + "try to use minimum ecc strength that NAND chip required\n", geo->ecc_strength, this->devdata->bch_max_ecc_strength); return -EINVAL; @@ -366,10 +367,11 @@ static int legacy_set_geometry(struct gpmi_nand_data *this) int common_nfc_set_geometry(struct gpmi_nand_data *this) { - if (of_property_read_bool(this->dev->of_node, "fsl,use-minimum-ecc") - && set_geometry_by_ecc_info(this)) - return 0; - return legacy_set_geometry(this); + if ((of_property_read_bool(this->dev->of_node, "fsl,use-minimum-ecc")) + || legacy_set_geometry(this)) + return set_geometry_by_ecc_info(this); + + return 0; } struct dma_chan *get_dma_chan(struct gpmi_nand_data *this) @@ -2033,9 +2035,54 @@ static int gpmi_nand_remove(struct platform_device *pdev) return 0; } +#ifdef CONFIG_PM_SLEEP +static int gpmi_pm_suspend(struct device *dev) +{ + struct gpmi_nand_data *this = dev_get_drvdata(dev); + + release_dma_channels(this); + return 0; +} + +static int gpmi_pm_resume(struct device *dev) +{ + struct gpmi_nand_data *this = dev_get_drvdata(dev); + int ret; + + ret = acquire_dma_channels(this); + if (ret < 0) + return ret; + + /* re-init the GPMI registers */ + this->flags &= ~GPMI_TIMING_INIT_OK; + ret = gpmi_init(this); + if (ret) { + dev_err(this->dev, "Error setting GPMI : %d\n", ret); + return ret; + } + + /* re-init the BCH registers */ + ret = bch_set_geometry(this); + if (ret) { + dev_err(this->dev, "Error setting BCH : %d\n", ret); + return ret; + } + + /* re-init others */ + gpmi_extra_init(this); + + return 0; +} +#endif /* CONFIG_PM_SLEEP */ + +static const struct dev_pm_ops gpmi_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(gpmi_pm_suspend, gpmi_pm_resume) +}; + static struct platform_driver gpmi_nand_driver = { .driver = { .name = "gpmi-nand", + .pm = &gpmi_pm_ops, .of_match_table = gpmi_nand_id_table, }, .probe = gpmi_nand_probe, diff --git a/drivers/mtd/nand/hisi504_nand.c b/drivers/mtd/nand/hisi504_nand.c index f8d37f36a81c..96502b624cfb 100644 --- a/drivers/mtd/nand/hisi504_nand.c +++ b/drivers/mtd/nand/hisi504_nand.c @@ -632,7 +632,6 @@ static void hisi_nfc_host_init(struct hinfc_host *host) } static struct nand_ecclayout nand_ecc_2K_16bits = { - .oobavail = 6, .oobfree = { {2, 6} }, }; diff --git a/drivers/mtd/nand/jz4740_nand.c b/drivers/mtd/nand/jz4740_nand.c index b19d2a9a5eb9..673ceb2a0b44 100644 --- a/drivers/mtd/nand/jz4740_nand.c +++ b/drivers/mtd/nand/jz4740_nand.c @@ -427,9 +427,6 @@ static int jz_nand_probe(struct platform_device *pdev) chip->ecc.strength = 4; chip->ecc.options = NAND_ECC_GENERIC_ERASED_CHECK; - if (pdata) - chip->ecc.layout = pdata->ecc_layout; - chip->chip_delay = 50; chip->cmd_ctrl = jz_nand_cmd_ctrl; chip->select_chip = jz_nand_select_chip; diff --git a/drivers/mtd/nand/lpc32xx_mlc.c b/drivers/mtd/nand/lpc32xx_mlc.c index 9bc435d72a86..d8c3e7afcc0b 100644 --- a/drivers/mtd/nand/lpc32xx_mlc.c +++ b/drivers/mtd/nand/lpc32xx_mlc.c @@ -750,7 +750,7 @@ static int lpc32xx_nand_probe(struct platform_device *pdev) } nand_chip->ecc.mode = NAND_ECC_HW; - nand_chip->ecc.size = mtd->writesize; + nand_chip->ecc.size = 512; nand_chip->ecc.layout = &lpc32xx_nand_oob; host->mlcsubpages = mtd->writesize / 512; diff --git a/drivers/mtd/nand/mpc5121_nfc.c b/drivers/mtd/nand/mpc5121_nfc.c index 6b93e899d4e9..5d7843ffff6a 100644 --- a/drivers/mtd/nand/mpc5121_nfc.c +++ b/drivers/mtd/nand/mpc5121_nfc.c @@ -626,7 +626,7 @@ static void mpc5121_nfc_free(struct device *dev, struct mtd_info *mtd) static int mpc5121_nfc_probe(struct platform_device *op) { - struct device_node *rootnode, *dn = op->dev.of_node; + struct device_node *dn = op->dev.of_node; struct clk *clk; struct device *dev = &op->dev; struct mpc5121_nfc_prv *prv; @@ -712,18 +712,15 @@ static int mpc5121_nfc_probe(struct platform_device *op) chip->ecc.mode = NAND_ECC_SOFT; /* Support external chip-select logic on ADS5121 board */ - rootnode = of_find_node_by_path("/"); - if (of_device_is_compatible(rootnode, "fsl,mpc5121ads")) { + if (of_machine_is_compatible("fsl,mpc5121ads")) { retval = ads5121_chipselect_init(mtd); if (retval) { dev_err(dev, "Chipselect init error!\n"); - of_node_put(rootnode); return retval; } chip->select_chip = ads5121_select_chip; } - of_node_put(rootnode); /* Enable NFC clock */ clk = devm_clk_get(dev, "ipg"); diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index f2c8ff398d6c..b6facac54fc0 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -313,13 +313,12 @@ static void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len) * nand_block_bad - [DEFAULT] Read bad block marker from the chip * @mtd: MTD device structure * @ofs: offset from device start - * @getchip: 0, if the chip is already selected * * Check, if the block is bad. */ -static int nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip) +static int nand_block_bad(struct mtd_info *mtd, loff_t ofs) { - int page, chipnr, res = 0, i = 0; + int page, res = 0, i = 0; struct nand_chip *chip = mtd_to_nand(mtd); u16 bad; @@ -328,15 +327,6 @@ static int nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip) page = (int)(ofs >> chip->page_shift) & chip->pagemask; - if (getchip) { - chipnr = (int)(ofs >> chip->chip_shift); - - nand_get_device(mtd, FL_READING); - - /* Select the NAND device */ - chip->select_chip(mtd, chipnr); - } - do { if (chip->options & NAND_BUSWIDTH_16) { chip->cmdfunc(mtd, NAND_CMD_READOOB, @@ -361,11 +351,6 @@ static int nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip) i++; } while (!res && i < 2 && (chip->bbt_options & NAND_BBT_SCAN2NDPAGE)); - if (getchip) { - chip->select_chip(mtd, -1); - nand_release_device(mtd); - } - return res; } @@ -503,19 +488,17 @@ static int nand_block_isreserved(struct mtd_info *mtd, loff_t ofs) * nand_block_checkbad - [GENERIC] Check if a block is marked bad * @mtd: MTD device structure * @ofs: offset from device start - * @getchip: 0, if the chip is already selected * @allowbbt: 1, if its allowed to access the bbt area * * Check, if the block is bad. Either by reading the bad block table or * calling of the scan function. */ -static int nand_block_checkbad(struct mtd_info *mtd, loff_t ofs, int getchip, - int allowbbt) +static int nand_block_checkbad(struct mtd_info *mtd, loff_t ofs, int allowbbt) { struct nand_chip *chip = mtd_to_nand(mtd); if (!chip->bbt) - return chip->block_bad(mtd, ofs, getchip); + return chip->block_bad(mtd, ofs); /* Return info from the table */ return nand_isbad_bbt(mtd, ofs, allowbbt); @@ -566,8 +549,8 @@ void nand_wait_ready(struct mtd_info *mtd) cond_resched(); } while (time_before(jiffies, timeo)); - pr_warn_ratelimited( - "timeout while waiting for chip to become ready\n"); + if (!chip->dev_ready(mtd)) + pr_warn_ratelimited("timeout while waiting for chip to become ready\n"); out: led_trigger_event(nand_led_trigger, LED_OFF); } @@ -1723,8 +1706,7 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, int ret = 0; uint32_t readlen = ops->len; uint32_t oobreadlen = ops->ooblen; - uint32_t max_oobsize = ops->mode == MTD_OPS_AUTO_OOB ? - mtd->oobavail : mtd->oobsize; + uint32_t max_oobsize = mtd_oobavail(mtd, ops); uint8_t *bufpoi, *oob, *buf; int use_bufpoi; @@ -2075,10 +2057,7 @@ static int nand_do_read_oob(struct mtd_info *mtd, loff_t from, stats = mtd->ecc_stats; - if (ops->mode == MTD_OPS_AUTO_OOB) - len = chip->ecc.layout->oobavail; - else - len = mtd->oobsize; + len = mtd_oobavail(mtd, ops); if (unlikely(ops->ooboffs >= len)) { pr_debug("%s: attempt to start read outside oob\n", @@ -2575,8 +2554,7 @@ static int nand_do_write_ops(struct mtd_info *mtd, loff_t to, uint32_t writelen = ops->len; uint32_t oobwritelen = ops->ooblen; - uint32_t oobmaxlen = ops->mode == MTD_OPS_AUTO_OOB ? - mtd->oobavail : mtd->oobsize; + uint32_t oobmaxlen = mtd_oobavail(mtd, ops); uint8_t *oob = ops->oobbuf; uint8_t *buf = ops->datbuf; @@ -2766,10 +2744,7 @@ static int nand_do_write_oob(struct mtd_info *mtd, loff_t to, pr_debug("%s: to = 0x%08x, len = %i\n", __func__, (unsigned int)to, (int)ops->ooblen); - if (ops->mode == MTD_OPS_AUTO_OOB) - len = chip->ecc.layout->oobavail; - else - len = mtd->oobsize; + len = mtd_oobavail(mtd, ops); /* Do not allow write past end of page */ if ((ops->ooboffs + ops->ooblen) > len) { @@ -2957,7 +2932,7 @@ int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr, while (len) { /* Check if we have a bad block, we do not erase bad blocks! */ if (nand_block_checkbad(mtd, ((loff_t) page) << - chip->page_shift, 0, allowbbt)) { + chip->page_shift, allowbbt)) { pr_warn("%s: attempt to erase a bad block at page 0x%08x\n", __func__, page); instr->state = MTD_ERASE_FAILED; @@ -3044,7 +3019,20 @@ static void nand_sync(struct mtd_info *mtd) */ static int nand_block_isbad(struct mtd_info *mtd, loff_t offs) { - return nand_block_checkbad(mtd, offs, 1, 0); + struct nand_chip *chip = mtd_to_nand(mtd); + int chipnr = (int)(offs >> chip->chip_shift); + int ret; + + /* Select the NAND device */ + nand_get_device(mtd, FL_READING); + chip->select_chip(mtd, chipnr); + + ret = nand_block_checkbad(mtd, offs, 0); + + chip->select_chip(mtd, -1); + nand_release_device(mtd); + + return ret; } /** @@ -4287,10 +4275,8 @@ int nand_scan_tail(struct mtd_info *mtd) } /* See nand_bch_init() for details. */ - ecc->bytes = DIV_ROUND_UP( - ecc->strength * fls(8 * ecc->size), 8); - ecc->priv = nand_bch_init(mtd, ecc->size, ecc->bytes, - &ecc->layout); + ecc->bytes = 0; + ecc->priv = nand_bch_init(mtd); if (!ecc->priv) { pr_warn("BCH ECC initialization failed!\n"); BUG(); @@ -4325,11 +4311,11 @@ int nand_scan_tail(struct mtd_info *mtd) * The number of bytes available for a client to place data into * the out of band area. */ - ecc->layout->oobavail = 0; - for (i = 0; ecc->layout->oobfree[i].length - && i < ARRAY_SIZE(ecc->layout->oobfree); i++) - ecc->layout->oobavail += ecc->layout->oobfree[i].length; - mtd->oobavail = ecc->layout->oobavail; + mtd->oobavail = 0; + if (ecc->layout) { + for (i = 0; ecc->layout->oobfree[i].length; i++) + mtd->oobavail += ecc->layout->oobfree[i].length; + } /* ECC sanity check: warn if it's too weak */ if (!nand_ecc_strength_good(mtd)) diff --git a/drivers/mtd/nand/nand_bbt.c b/drivers/mtd/nand/nand_bbt.c index 4b6a7085b442..2fbb523df066 100644 --- a/drivers/mtd/nand/nand_bbt.c +++ b/drivers/mtd/nand/nand_bbt.c @@ -1373,5 +1373,3 @@ int nand_markbad_bbt(struct mtd_info *mtd, loff_t offs) return ret; } - -EXPORT_SYMBOL(nand_scan_bbt); diff --git a/drivers/mtd/nand/nand_bch.c b/drivers/mtd/nand/nand_bch.c index a87c1b628dfc..b585bae37929 100644 --- a/drivers/mtd/nand/nand_bch.c +++ b/drivers/mtd/nand/nand_bch.c @@ -107,9 +107,6 @@ EXPORT_SYMBOL(nand_bch_correct_data); /** * nand_bch_init - [NAND Interface] Initialize NAND BCH error correction * @mtd: MTD block structure - * @eccsize: ecc block size in bytes - * @eccbytes: ecc length in bytes - * @ecclayout: output default layout * * Returns: * a pointer to a new NAND BCH control structure, or NULL upon failure @@ -123,14 +120,21 @@ EXPORT_SYMBOL(nand_bch_correct_data); * @eccsize = 512 (thus, m=13 is the smallest integer such that 2^m-1 > 512*8) * @eccbytes = 7 (7 bytes are required to store m*t = 13*4 = 52 bits) */ -struct nand_bch_control * -nand_bch_init(struct mtd_info *mtd, unsigned int eccsize, unsigned int eccbytes, - struct nand_ecclayout **ecclayout) +struct nand_bch_control *nand_bch_init(struct mtd_info *mtd) { + struct nand_chip *nand = mtd_to_nand(mtd); unsigned int m, t, eccsteps, i; - struct nand_ecclayout *layout; + struct nand_ecclayout *layout = nand->ecc.layout; struct nand_bch_control *nbc = NULL; unsigned char *erased_page; + unsigned int eccsize = nand->ecc.size; + unsigned int eccbytes = nand->ecc.bytes; + unsigned int eccstrength = nand->ecc.strength; + + if (!eccbytes && eccstrength) { + eccbytes = DIV_ROUND_UP(eccstrength * fls(8 * eccsize), 8); + nand->ecc.bytes = eccbytes; + } if (!eccsize || !eccbytes) { printk(KERN_WARNING "ecc parameters not supplied\n"); @@ -158,7 +162,7 @@ nand_bch_init(struct mtd_info *mtd, unsigned int eccsize, unsigned int eccbytes, eccsteps = mtd->writesize/eccsize; /* if no ecc placement scheme was provided, build one */ - if (!*ecclayout) { + if (!layout) { /* handle large page devices only */ if (mtd->oobsize < 64) { @@ -184,7 +188,7 @@ nand_bch_init(struct mtd_info *mtd, unsigned int eccsize, unsigned int eccbytes, layout->oobfree[0].offset = 2; layout->oobfree[0].length = mtd->oobsize-2-layout->eccbytes; - *ecclayout = layout; + nand->ecc.layout = layout; } /* sanity checks */ @@ -192,7 +196,7 @@ nand_bch_init(struct mtd_info *mtd, unsigned int eccsize, unsigned int eccbytes, printk(KERN_WARNING "eccsize %u is too large\n", eccsize); goto fail; } - if ((*ecclayout)->eccbytes != (eccsteps*eccbytes)) { + if (layout->eccbytes != (eccsteps*eccbytes)) { printk(KERN_WARNING "invalid ecc layout\n"); goto fail; } @@ -216,6 +220,9 @@ nand_bch_init(struct mtd_info *mtd, unsigned int eccsize, unsigned int eccbytes, for (i = 0; i < eccbytes; i++) nbc->eccmask[i] ^= 0xff; + if (!eccstrength) + nand->ecc.strength = (eccbytes * 8) / fls(8 * eccsize); + return nbc; fail: nand_bch_free(nbc); diff --git a/drivers/mtd/nand/nand_ids.c b/drivers/mtd/nand/nand_ids.c index a8804a3da076..ccc05f5b2695 100644 --- a/drivers/mtd/nand/nand_ids.c +++ b/drivers/mtd/nand/nand_ids.c @@ -50,8 +50,8 @@ struct nand_flash_dev nand_flash_ids[] = { SZ_16K, SZ_8K, SZ_4M, 0, 6, 1280, NAND_ECC_INFO(40, SZ_1K) }, {"H27UCG8T2ATR-BC 64G 3.3V 8-bit", { .id = {0xad, 0xde, 0x94, 0xda, 0x74, 0xc4} }, - SZ_8K, SZ_8K, SZ_2M, 0, 6, 640, NAND_ECC_INFO(40, SZ_1K), - 4 }, + SZ_8K, SZ_8K, SZ_2M, NAND_NEED_SCRAMBLING, 6, 640, + NAND_ECC_INFO(40, SZ_1K), 4 }, LEGACY_ID_NAND("NAND 4MiB 5V 8-bit", 0x6B, 4, SZ_8K, SP_OPTIONS), LEGACY_ID_NAND("NAND 4MiB 3,3V 8-bit", 0xE3, 4, SZ_8K, SP_OPTIONS), diff --git a/drivers/mtd/nand/nuc900_nand.c b/drivers/mtd/nand/nuc900_nand.c index 220ddfcf29f5..dbc5b571c2bb 100644 --- a/drivers/mtd/nand/nuc900_nand.c +++ b/drivers/mtd/nand/nuc900_nand.c @@ -113,7 +113,7 @@ static int nuc900_check_rb(struct nuc900_nand *nand) { unsigned int val; spin_lock(&nand->lock); - val = __raw_readl(REG_SMISR); + val = __raw_readl(nand->reg + REG_SMISR); val &= READYBUSY; spin_unlock(&nand->lock); diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c index c553f78ab83f..0749ca1a1456 100644 --- a/drivers/mtd/nand/omap2.c +++ b/drivers/mtd/nand/omap2.c @@ -1807,13 +1807,19 @@ static int omap_nand_probe(struct platform_device *pdev) goto return_error; } + /* + * Bail out earlier to let NAND_ECC_SOFT code create its own + * ecclayout instead of using ours. + */ + if (info->ecc_opt == OMAP_ECC_HAM1_CODE_SW) { + nand_chip->ecc.mode = NAND_ECC_SOFT; + goto scan_tail; + } + /* populate MTD interface based on ECC scheme */ ecclayout = &info->oobinfo; + nand_chip->ecc.layout = ecclayout; switch (info->ecc_opt) { - case OMAP_ECC_HAM1_CODE_SW: - nand_chip->ecc.mode = NAND_ECC_SOFT; - break; - case OMAP_ECC_HAM1_CODE_HW: pr_info("nand: using OMAP_ECC_HAM1_CODE_HW\n"); nand_chip->ecc.mode = NAND_ECC_HW; @@ -1861,10 +1867,7 @@ static int omap_nand_probe(struct platform_device *pdev) ecclayout->oobfree->offset = 1 + ecclayout->eccpos[ecclayout->eccbytes - 1] + 1; /* software bch library is used for locating errors */ - nand_chip->ecc.priv = nand_bch_init(mtd, - nand_chip->ecc.size, - nand_chip->ecc.bytes, - &ecclayout); + nand_chip->ecc.priv = nand_bch_init(mtd); if (!nand_chip->ecc.priv) { dev_err(&info->pdev->dev, "unable to use BCH library\n"); err = -EINVAL; @@ -1925,10 +1928,7 @@ static int omap_nand_probe(struct platform_device *pdev) ecclayout->oobfree->offset = 1 + ecclayout->eccpos[ecclayout->eccbytes - 1] + 1; /* software bch library is used for locating errors */ - nand_chip->ecc.priv = nand_bch_init(mtd, - nand_chip->ecc.size, - nand_chip->ecc.bytes, - &ecclayout); + nand_chip->ecc.priv = nand_bch_init(mtd); if (!nand_chip->ecc.priv) { dev_err(&info->pdev->dev, "unable to use BCH library\n"); err = -EINVAL; @@ -2002,9 +2002,6 @@ static int omap_nand_probe(struct platform_device *pdev) goto return_error; } - if (info->ecc_opt == OMAP_ECC_HAM1_CODE_SW) - goto scan_tail; - /* all OOB bytes from oobfree->offset till end off OOB are free */ ecclayout->oobfree->length = mtd->oobsize - ecclayout->oobfree->offset; /* check if NAND device's OOB is enough to store ECC signatures */ @@ -2015,7 +2012,6 @@ static int omap_nand_probe(struct platform_device *pdev) err = -EINVAL; goto return_error; } - nand_chip->ecc.layout = ecclayout; scan_tail: /* second phase scan */ diff --git a/drivers/mtd/nand/plat_nand.c b/drivers/mtd/nand/plat_nand.c index a0e26dea1424..e4e50da30444 100644 --- a/drivers/mtd/nand/plat_nand.c +++ b/drivers/mtd/nand/plat_nand.c @@ -73,7 +73,6 @@ static int plat_nand_probe(struct platform_device *pdev) data->chip.bbt_options |= pdata->chip.bbt_options; data->chip.ecc.hwctl = pdata->ctrl.hwcontrol; - data->chip.ecc.layout = pdata->chip.ecclayout; data->chip.ecc.mode = NAND_ECC_SOFT; platform_set_drvdata(pdev, data); diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c index 86fc245dc71a..d6508856da99 100644 --- a/drivers/mtd/nand/pxa3xx_nand.c +++ b/drivers/mtd/nand/pxa3xx_nand.c @@ -131,11 +131,23 @@ #define READ_ID_BYTES 7 /* macros for registers read/write */ -#define nand_writel(info, off, val) \ - writel_relaxed((val), (info)->mmio_base + (off)) - -#define nand_readl(info, off) \ - readl_relaxed((info)->mmio_base + (off)) +#define nand_writel(info, off, val) \ + do { \ + dev_vdbg(&info->pdev->dev, \ + "%s():%d nand_writel(0x%x, 0x%04x)\n", \ + __func__, __LINE__, (val), (off)); \ + writel_relaxed((val), (info)->mmio_base + (off)); \ + } while (0) + +#define nand_readl(info, off) \ + ({ \ + unsigned int _v; \ + _v = readl_relaxed((info)->mmio_base + (off)); \ + dev_vdbg(&info->pdev->dev, \ + "%s():%d nand_readl(0x%04x) = 0x%x\n", \ + __func__, __LINE__, (off), _v); \ + _v; \ + }) /* error code and state */ enum { @@ -199,7 +211,6 @@ struct pxa3xx_nand_info { struct dma_chan *dma_chan; dma_cookie_t dma_cookie; int drcmr_dat; - int drcmr_cmd; unsigned char *data_buff; unsigned char *oob_buff; @@ -222,15 +233,44 @@ struct pxa3xx_nand_info { int use_spare; /* use spare ? */ int need_wait; - unsigned int data_size; /* data to be read from FIFO */ - unsigned int chunk_size; /* split commands chunk size */ - unsigned int oob_size; + /* Amount of real data per full chunk */ + unsigned int chunk_size; + + /* Amount of spare data per full chunk */ unsigned int spare_size; + + /* Number of full chunks (i.e chunk_size + spare_size) */ + unsigned int nfullchunks; + + /* + * Total number of chunks. If equal to nfullchunks, then there + * are only full chunks. Otherwise, there is one last chunk of + * size (last_chunk_size + last_spare_size) + */ + unsigned int ntotalchunks; + + /* Amount of real data in the last chunk */ + unsigned int last_chunk_size; + + /* Amount of spare data in the last chunk */ + unsigned int last_spare_size; + unsigned int ecc_size; unsigned int ecc_err_cnt; unsigned int max_bitflips; int retcode; + /* + * Variables only valid during command + * execution. step_chunk_size and step_spare_size is the + * amount of real data and spare data in the current + * chunk. cur_chunk is the current chunk being + * read/programmed. + */ + unsigned int step_chunk_size; + unsigned int step_spare_size; + unsigned int cur_chunk; + /* cached register value */ uint32_t reg_ndcr; uint32_t ndtr0cs0; @@ -526,25 +566,6 @@ static int pxa3xx_nand_init(struct pxa3xx_nand_host *host) return 0; } -/* - * Set the data and OOB size, depending on the selected - * spare and ECC configuration. - * Only applicable to READ0, READOOB and PAGEPROG commands. - */ -static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info, - struct mtd_info *mtd) -{ - int oob_enable = info->reg_ndcr & NDCR_SPARE_EN; - - info->data_size = mtd->writesize; - if (!oob_enable) - return; - - info->oob_size = info->spare_size; - if (!info->use_ecc) - info->oob_size += info->ecc_size; -} - /** * NOTE: it is a must to set ND_RUN firstly, then write * command buffer, otherwise, it does not work. @@ -660,28 +681,28 @@ static void drain_fifo(struct pxa3xx_nand_info *info, void *data, int len) static void handle_data_pio(struct pxa3xx_nand_info *info) { - unsigned int do_bytes = min(info->data_size, info->chunk_size); - switch (info->state) { case STATE_PIO_WRITING: - writesl(info->mmio_base + NDDB, - info->data_buff + info->data_buff_pos, - DIV_ROUND_UP(do_bytes, 4)); + if (info->step_chunk_size) + writesl(info->mmio_base + NDDB, + info->data_buff + info->data_buff_pos, + DIV_ROUND_UP(info->step_chunk_size, 4)); - if (info->oob_size > 0) + if (info->step_spare_size) writesl(info->mmio_base + NDDB, info->oob_buff + info->oob_buff_pos, - DIV_ROUND_UP(info->oob_size, 4)); + DIV_ROUND_UP(info->step_spare_size, 4)); break; case STATE_PIO_READING: - drain_fifo(info, - info->data_buff + info->data_buff_pos, - DIV_ROUND_UP(do_bytes, 4)); + if (info->step_chunk_size) + drain_fifo(info, + info->data_buff + info->data_buff_pos, + DIV_ROUND_UP(info->step_chunk_size, 4)); - if (info->oob_size > 0) + if (info->step_spare_size) drain_fifo(info, info->oob_buff + info->oob_buff_pos, - DIV_ROUND_UP(info->oob_size, 4)); + DIV_ROUND_UP(info->step_spare_size, 4)); break; default: dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__, @@ -690,9 +711,8 @@ static void handle_data_pio(struct pxa3xx_nand_info *info) } /* Update buffer pointers for multi-page read/write */ - info->data_buff_pos += do_bytes; - info->oob_buff_pos += info->oob_size; - info->data_size -= do_bytes; + info->data_buff_pos += info->step_chunk_size; + info->oob_buff_pos += info->step_spare_size; } static void pxa3xx_nand_data_dma_irq(void *data) @@ -733,8 +753,9 @@ static void start_data_dma(struct pxa3xx_nand_info *info) info->state); BUG(); } - info->sg.length = info->data_size + - (info->oob_size ? info->spare_size + info->ecc_size : 0); + info->sg.length = info->chunk_size; + if (info->use_spare) + info->sg.length += info->spare_size + info->ecc_size; dma_map_sg(info->dma_chan->device->dev, &info->sg, 1, info->dma_dir); tx = dmaengine_prep_slave_sg(info->dma_chan, &info->sg, 1, direction, @@ -895,9 +916,11 @@ static void prepare_start_command(struct pxa3xx_nand_info *info, int command) /* reset data and oob column point to handle data */ info->buf_start = 0; info->buf_count = 0; - info->oob_size = 0; info->data_buff_pos = 0; info->oob_buff_pos = 0; + info->step_chunk_size = 0; + info->step_spare_size = 0; + info->cur_chunk = 0; info->use_ecc = 0; info->use_spare = 1; info->retcode = ERR_NONE; @@ -909,8 +932,6 @@ static void prepare_start_command(struct pxa3xx_nand_info *info, int command) case NAND_CMD_READ0: case NAND_CMD_PAGEPROG: info->use_ecc = 1; - case NAND_CMD_READOOB: - pxa3xx_set_datasize(info, mtd); break; case NAND_CMD_PARAM: info->use_spare = 0; @@ -969,6 +990,14 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command, if (command == NAND_CMD_READOOB) info->buf_start += mtd->writesize; + if (info->cur_chunk < info->nfullchunks) { + info->step_chunk_size = info->chunk_size; + info->step_spare_size = info->spare_size; + } else { + info->step_chunk_size = info->last_chunk_size; + info->step_spare_size = info->last_spare_size; + } + /* * Multiple page read needs an 'extended command type' field, * which is either naked-read or last-read according to the @@ -980,8 +1009,8 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command, info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8) | NDCB0_LEN_OVRD | NDCB0_EXT_CMD_TYPE(ext_cmd_type); - info->ndcb3 = info->chunk_size + - info->oob_size; + info->ndcb3 = info->step_chunk_size + + info->step_spare_size; } set_command_address(info, mtd->writesize, column, page_addr); @@ -1001,8 +1030,6 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command, | NDCB0_EXT_CMD_TYPE(ext_cmd_type) | addr_cycle | command; - /* No data transfer in this case */ - info->data_size = 0; exec_cmd = 1; } break; @@ -1014,6 +1041,14 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command, break; } + if (info->cur_chunk < info->nfullchunks) { + info->step_chunk_size = info->chunk_size; + info->step_spare_size = info->spare_size; + } else { + info->step_chunk_size = info->last_chunk_size; + info->step_spare_size = info->last_spare_size; + } + /* Second command setting for large pages */ if (mtd->writesize > PAGE_CHUNK_SIZE) { /* @@ -1024,14 +1059,14 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command, info->ndcb0 |= NDCB0_CMD_TYPE(0x1) | NDCB0_LEN_OVRD | NDCB0_EXT_CMD_TYPE(ext_cmd_type); - info->ndcb3 = info->chunk_size + - info->oob_size; + info->ndcb3 = info->step_chunk_size + + info->step_spare_size; /* * This is the command dispatch that completes a chunked * page program operation. */ - if (info->data_size == 0) { + if (info->cur_chunk == info->ntotalchunks) { info->ndcb0 = NDCB0_CMD_TYPE(0x1) | NDCB0_EXT_CMD_TYPE(ext_cmd_type) | command; @@ -1058,7 +1093,7 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command, | command; info->ndcb1 = (column & 0xFF); info->ndcb3 = INIT_BUFFER_SIZE; - info->data_size = INIT_BUFFER_SIZE; + info->step_chunk_size = INIT_BUFFER_SIZE; break; case NAND_CMD_READID: @@ -1068,7 +1103,7 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command, | command; info->ndcb1 = (column & 0xFF); - info->data_size = 8; + info->step_chunk_size = 8; break; case NAND_CMD_STATUS: info->buf_count = 1; @@ -1076,7 +1111,7 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command, | NDCB0_ADDR_CYC(1) | command; - info->data_size = 8; + info->step_chunk_size = 8; break; case NAND_CMD_ERASE1: @@ -1217,6 +1252,7 @@ static void nand_cmdfunc_extended(struct mtd_info *mtd, init_completion(&info->dev_ready); do { info->state = STATE_PREPARED; + exec_cmd = prepare_set_command(info, command, ext_cmd_type, column, page_addr); if (!exec_cmd) { @@ -1236,22 +1272,30 @@ static void nand_cmdfunc_extended(struct mtd_info *mtd, break; } + /* Only a few commands need several steps */ + if (command != NAND_CMD_PAGEPROG && + command != NAND_CMD_READ0 && + command != NAND_CMD_READOOB) + break; + + info->cur_chunk++; + /* Check if the sequence is complete */ - if (info->data_size == 0 && command != NAND_CMD_PAGEPROG) + if (info->cur_chunk == info->ntotalchunks && command != NAND_CMD_PAGEPROG) break; /* * After a splitted program command sequence has issued * the command dispatch, the command sequence is complete. */ - if (info->data_size == 0 && + if (info->cur_chunk == (info->ntotalchunks + 1) && command == NAND_CMD_PAGEPROG && ext_cmd_type == EXT_CMD_TYPE_DISPATCH) break; if (command == NAND_CMD_READ0 || command == NAND_CMD_READOOB) { /* Last read: issue a 'last naked read' */ - if (info->data_size == info->chunk_size) + if (info->cur_chunk == info->ntotalchunks - 1) ext_cmd_type = EXT_CMD_TYPE_LAST_RW; else ext_cmd_type = EXT_CMD_TYPE_NAKED_RW; @@ -1261,7 +1305,7 @@ static void nand_cmdfunc_extended(struct mtd_info *mtd, * the command dispatch must be issued to complete. */ } else if (command == NAND_CMD_PAGEPROG && - info->data_size == 0) { + info->cur_chunk == info->ntotalchunks) { ext_cmd_type = EXT_CMD_TYPE_DISPATCH; } } while (1); @@ -1506,6 +1550,8 @@ static int pxa_ecc_init(struct pxa3xx_nand_info *info, int strength, int ecc_stepsize, int page_size) { if (strength == 1 && ecc_stepsize == 512 && page_size == 2048) { + info->nfullchunks = 1; + info->ntotalchunks = 1; info->chunk_size = 2048; info->spare_size = 40; info->ecc_size = 24; @@ -1514,6 +1560,8 @@ static int pxa_ecc_init(struct pxa3xx_nand_info *info, ecc->strength = 1; } else if (strength == 1 && ecc_stepsize == 512 && page_size == 512) { + info->nfullchunks = 1; + info->ntotalchunks = 1; info->chunk_size = 512; info->spare_size = 8; info->ecc_size = 8; @@ -1527,6 +1575,8 @@ static int pxa_ecc_init(struct pxa3xx_nand_info *info, */ } else if (strength == 4 && ecc_stepsize == 512 && page_size == 2048) { info->ecc_bch = 1; + info->nfullchunks = 1; + info->ntotalchunks = 1; info->chunk_size = 2048; info->spare_size = 32; info->ecc_size = 32; @@ -1537,6 +1587,8 @@ static int pxa_ecc_init(struct pxa3xx_nand_info *info, } else if (strength == 4 && ecc_stepsize == 512 && page_size == 4096) { info->ecc_bch = 1; + info->nfullchunks = 2; + info->ntotalchunks = 2; info->chunk_size = 2048; info->spare_size = 32; info->ecc_size = 32; @@ -1551,8 +1603,12 @@ static int pxa_ecc_init(struct pxa3xx_nand_info *info, */ } else if (strength == 8 && ecc_stepsize == 512 && page_size == 4096) { info->ecc_bch = 1; + info->nfullchunks = 4; + info->ntotalchunks = 5; info->chunk_size = 1024; info->spare_size = 0; + info->last_chunk_size = 0; + info->last_spare_size = 64; info->ecc_size = 32; ecc->mode = NAND_ECC_HW; ecc->size = info->chunk_size; @@ -1738,7 +1794,7 @@ static int alloc_nand_resource(struct platform_device *pdev) if (ret < 0) return ret; - if (use_dma) { + if (!np && use_dma) { r = platform_get_resource(pdev, IORESOURCE_DMA, 0); if (r == NULL) { dev_err(&pdev->dev, @@ -1747,15 +1803,6 @@ static int alloc_nand_resource(struct platform_device *pdev) goto fail_disable_clk; } info->drcmr_dat = r->start; - - r = platform_get_resource(pdev, IORESOURCE_DMA, 1); - if (r == NULL) { - dev_err(&pdev->dev, - "no resource defined for cmd DMA\n"); - ret = -ENXIO; - goto fail_disable_clk; - } - info->drcmr_cmd = r->start; } irq = platform_get_irq(pdev, 0); diff --git a/drivers/mtd/nand/qcom_nandc.c b/drivers/mtd/nand/qcom_nandc.c new file mode 100644 index 000000000000..f550a57e6eea --- /dev/null +++ b/drivers/mtd/nand/qcom_nandc.c @@ -0,0 +1,2223 @@ +/* + * Copyright (c) 2016, The Linux Foundation. All rights reserved. + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/clk.h> +#include <linux/slab.h> +#include <linux/bitops.h> +#include <linux/dma-mapping.h> +#include <linux/dmaengine.h> +#include <linux/module.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/of_mtd.h> +#include <linux/delay.h> + +/* NANDc reg offsets */ +#define NAND_FLASH_CMD 0x00 +#define NAND_ADDR0 0x04 +#define NAND_ADDR1 0x08 +#define NAND_FLASH_CHIP_SELECT 0x0c +#define NAND_EXEC_CMD 0x10 +#define NAND_FLASH_STATUS 0x14 +#define NAND_BUFFER_STATUS 0x18 +#define NAND_DEV0_CFG0 0x20 +#define NAND_DEV0_CFG1 0x24 +#define NAND_DEV0_ECC_CFG 0x28 +#define NAND_DEV1_ECC_CFG 0x2c +#define NAND_DEV1_CFG0 0x30 +#define NAND_DEV1_CFG1 0x34 +#define NAND_READ_ID 0x40 +#define NAND_READ_STATUS 0x44 +#define NAND_DEV_CMD0 0xa0 +#define NAND_DEV_CMD1 0xa4 +#define NAND_DEV_CMD2 0xa8 +#define NAND_DEV_CMD_VLD 0xac +#define SFLASHC_BURST_CFG 0xe0 +#define NAND_ERASED_CW_DETECT_CFG 0xe8 +#define NAND_ERASED_CW_DETECT_STATUS 0xec +#define NAND_EBI2_ECC_BUF_CFG 0xf0 +#define FLASH_BUF_ACC 0x100 + +#define NAND_CTRL 0xf00 +#define NAND_VERSION 0xf08 +#define NAND_READ_LOCATION_0 0xf20 +#define NAND_READ_LOCATION_1 0xf24 + +/* dummy register offsets, used by write_reg_dma */ +#define NAND_DEV_CMD1_RESTORE 0xdead +#define NAND_DEV_CMD_VLD_RESTORE 0xbeef + +/* NAND_FLASH_CMD bits */ +#define PAGE_ACC BIT(4) +#define LAST_PAGE BIT(5) + +/* NAND_FLASH_CHIP_SELECT bits */ +#define NAND_DEV_SEL 0 +#define DM_EN BIT(2) + +/* NAND_FLASH_STATUS bits */ +#define FS_OP_ERR BIT(4) +#define FS_READY_BSY_N BIT(5) +#define FS_MPU_ERR BIT(8) +#define FS_DEVICE_STS_ERR BIT(16) +#define FS_DEVICE_WP BIT(23) + +/* NAND_BUFFER_STATUS bits */ +#define BS_UNCORRECTABLE_BIT BIT(8) +#define BS_CORRECTABLE_ERR_MSK 0x1f + +/* NAND_DEVn_CFG0 bits */ +#define DISABLE_STATUS_AFTER_WRITE 4 +#define CW_PER_PAGE 6 +#define UD_SIZE_BYTES 9 +#define ECC_PARITY_SIZE_BYTES_RS 19 +#define SPARE_SIZE_BYTES 23 +#define NUM_ADDR_CYCLES 27 +#define STATUS_BFR_READ 30 +#define SET_RD_MODE_AFTER_STATUS 31 + +/* NAND_DEVn_CFG0 bits */ +#define DEV0_CFG1_ECC_DISABLE 0 +#define WIDE_FLASH 1 +#define NAND_RECOVERY_CYCLES 2 +#define CS_ACTIVE_BSY 5 +#define BAD_BLOCK_BYTE_NUM 6 +#define BAD_BLOCK_IN_SPARE_AREA 16 +#define WR_RD_BSY_GAP 17 +#define ENABLE_BCH_ECC 27 + +/* NAND_DEV0_ECC_CFG bits */ +#define ECC_CFG_ECC_DISABLE 0 +#define ECC_SW_RESET 1 +#define ECC_MODE 4 +#define ECC_PARITY_SIZE_BYTES_BCH 8 +#define ECC_NUM_DATA_BYTES 16 +#define ECC_FORCE_CLK_OPEN 30 + +/* NAND_DEV_CMD1 bits */ +#define READ_ADDR 0 + +/* NAND_DEV_CMD_VLD bits */ +#define READ_START_VLD 0 + +/* NAND_EBI2_ECC_BUF_CFG bits */ +#define NUM_STEPS 0 + +/* NAND_ERASED_CW_DETECT_CFG bits */ +#define ERASED_CW_ECC_MASK 1 +#define AUTO_DETECT_RES 0 +#define MASK_ECC (1 << ERASED_CW_ECC_MASK) +#define RESET_ERASED_DET (1 << AUTO_DETECT_RES) +#define ACTIVE_ERASED_DET (0 << AUTO_DETECT_RES) +#define CLR_ERASED_PAGE_DET (RESET_ERASED_DET | MASK_ECC) +#define SET_ERASED_PAGE_DET (ACTIVE_ERASED_DET | MASK_ECC) + +/* NAND_ERASED_CW_DETECT_STATUS bits */ +#define PAGE_ALL_ERASED BIT(7) +#define CODEWORD_ALL_ERASED BIT(6) +#define PAGE_ERASED BIT(5) +#define CODEWORD_ERASED BIT(4) +#define ERASED_PAGE (PAGE_ALL_ERASED | PAGE_ERASED) +#define ERASED_CW (CODEWORD_ALL_ERASED | CODEWORD_ERASED) + +/* Version Mask */ +#define NAND_VERSION_MAJOR_MASK 0xf0000000 +#define NAND_VERSION_MAJOR_SHIFT 28 +#define NAND_VERSION_MINOR_MASK 0x0fff0000 +#define NAND_VERSION_MINOR_SHIFT 16 + +/* NAND OP_CMDs */ +#define PAGE_READ 0x2 +#define PAGE_READ_WITH_ECC 0x3 +#define PAGE_READ_WITH_ECC_SPARE 0x4 +#define PROGRAM_PAGE 0x6 +#define PAGE_PROGRAM_WITH_ECC 0x7 +#define PROGRAM_PAGE_SPARE 0x9 +#define BLOCK_ERASE 0xa +#define FETCH_ID 0xb +#define RESET_DEVICE 0xd + +/* + * the NAND controller performs reads/writes with ECC in 516 byte chunks. + * the driver calls the chunks 'step' or 'codeword' interchangeably + */ +#define NANDC_STEP_SIZE 512 + +/* + * the largest page size we support is 8K, this will have 16 steps/codewords + * of 512 bytes each + */ +#define MAX_NUM_STEPS (SZ_8K / NANDC_STEP_SIZE) + +/* we read at most 3 registers per codeword scan */ +#define MAX_REG_RD (3 * MAX_NUM_STEPS) + +/* ECC modes supported by the controller */ +#define ECC_NONE BIT(0) +#define ECC_RS_4BIT BIT(1) +#define ECC_BCH_4BIT BIT(2) +#define ECC_BCH_8BIT BIT(3) + +struct desc_info { + struct list_head node; + + enum dma_data_direction dir; + struct scatterlist sgl; + struct dma_async_tx_descriptor *dma_desc; +}; + +/* + * holds the current register values that we want to write. acts as a contiguous + * chunk of memory which we use to write the controller registers through DMA. + */ +struct nandc_regs { + __le32 cmd; + __le32 addr0; + __le32 addr1; + __le32 chip_sel; + __le32 exec; + + __le32 cfg0; + __le32 cfg1; + __le32 ecc_bch_cfg; + + __le32 clrflashstatus; + __le32 clrreadstatus; + + __le32 cmd1; + __le32 vld; + + __le32 orig_cmd1; + __le32 orig_vld; + + __le32 ecc_buf_cfg; +}; + +/* + * NAND controller data struct + * + * @controller: base controller structure + * @host_list: list containing all the chips attached to the + * controller + * @dev: parent device + * @base: MMIO base + * @base_dma: physical base address of controller registers + * @core_clk: controller clock + * @aon_clk: another controller clock + * + * @chan: dma channel + * @cmd_crci: ADM DMA CRCI for command flow control + * @data_crci: ADM DMA CRCI for data flow control + * @desc_list: DMA descriptor list (list of desc_infos) + * + * @data_buffer: our local DMA buffer for page read/writes, + * used when we can't use the buffer provided + * by upper layers directly + * @buf_size/count/start: markers for chip->read_buf/write_buf functions + * @reg_read_buf: local buffer for reading back registers via DMA + * @reg_read_pos: marker for data read in reg_read_buf + * + * @regs: a contiguous chunk of memory for DMA register + * writes. contains the register values to be + * written to controller + * @cmd1/vld: some fixed controller register values + * @ecc_modes: supported ECC modes by the current controller, + * initialized via DT match data + */ +struct qcom_nand_controller { + struct nand_hw_control controller; + struct list_head host_list; + + struct device *dev; + + void __iomem *base; + dma_addr_t base_dma; + + struct clk *core_clk; + struct clk *aon_clk; + + struct dma_chan *chan; + unsigned int cmd_crci; + unsigned int data_crci; + struct list_head desc_list; + + u8 *data_buffer; + int buf_size; + int buf_count; + int buf_start; + + __le32 *reg_read_buf; + int reg_read_pos; + + struct nandc_regs *regs; + + u32 cmd1, vld; + u32 ecc_modes; +}; + +/* + * NAND chip structure + * + * @chip: base NAND chip structure + * @node: list node to add itself to host_list in + * qcom_nand_controller + * + * @cs: chip select value for this chip + * @cw_size: the number of bytes in a single step/codeword + * of a page, consisting of all data, ecc, spare + * and reserved bytes + * @cw_data: the number of bytes within a codeword protected + * by ECC + * @use_ecc: request the controller to use ECC for the + * upcoming read/write + * @bch_enabled: flag to tell whether BCH ECC mode is used + * @ecc_bytes_hw: ECC bytes used by controller hardware for this + * chip + * @status: value to be returned if NAND_CMD_STATUS command + * is executed + * @last_command: keeps track of last command on this chip. used + * for reading correct status + * + * @cfg0, cfg1, cfg0_raw..: NANDc register configurations needed for + * ecc/non-ecc mode for the current nand flash + * device + */ +struct qcom_nand_host { + struct nand_chip chip; + struct list_head node; + + int cs; + int cw_size; + int cw_data; + bool use_ecc; + bool bch_enabled; + int ecc_bytes_hw; + int spare_bytes; + int bbm_size; + u8 status; + int last_command; + + u32 cfg0, cfg1; + u32 cfg0_raw, cfg1_raw; + u32 ecc_buf_cfg; + u32 ecc_bch_cfg; + u32 clrflashstatus; + u32 clrreadstatus; +}; + +static inline struct qcom_nand_host *to_qcom_nand_host(struct nand_chip *chip) +{ + return container_of(chip, struct qcom_nand_host, chip); +} + +static inline struct qcom_nand_controller * +get_qcom_nand_controller(struct nand_chip *chip) +{ + return container_of(chip->controller, struct qcom_nand_controller, + controller); +} + +static inline u32 nandc_read(struct qcom_nand_controller *nandc, int offset) +{ + return ioread32(nandc->base + offset); +} + +static inline void nandc_write(struct qcom_nand_controller *nandc, int offset, + u32 val) +{ + iowrite32(val, nandc->base + offset); +} + +static __le32 *offset_to_nandc_reg(struct nandc_regs *regs, int offset) +{ + switch (offset) { + case NAND_FLASH_CMD: + return ®s->cmd; + case NAND_ADDR0: + return ®s->addr0; + case NAND_ADDR1: + return ®s->addr1; + case NAND_FLASH_CHIP_SELECT: + return ®s->chip_sel; + case NAND_EXEC_CMD: + return ®s->exec; + case NAND_FLASH_STATUS: + return ®s->clrflashstatus; + case NAND_DEV0_CFG0: + return ®s->cfg0; + case NAND_DEV0_CFG1: + return ®s->cfg1; + case NAND_DEV0_ECC_CFG: + return ®s->ecc_bch_cfg; + case NAND_READ_STATUS: + return ®s->clrreadstatus; + case NAND_DEV_CMD1: + return ®s->cmd1; + case NAND_DEV_CMD1_RESTORE: + return ®s->orig_cmd1; + case NAND_DEV_CMD_VLD: + return ®s->vld; + case NAND_DEV_CMD_VLD_RESTORE: + return ®s->orig_vld; + case NAND_EBI2_ECC_BUF_CFG: + return ®s->ecc_buf_cfg; + default: + return NULL; + } +} + +static void nandc_set_reg(struct qcom_nand_controller *nandc, int offset, + u32 val) +{ + struct nandc_regs *regs = nandc->regs; + __le32 *reg; + + reg = offset_to_nandc_reg(regs, offset); + + if (reg) + *reg = cpu_to_le32(val); +} + +/* helper to configure address register values */ +static void set_address(struct qcom_nand_host *host, u16 column, int page) +{ + struct nand_chip *chip = &host->chip; + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + + if (chip->options & NAND_BUSWIDTH_16) + column >>= 1; + + nandc_set_reg(nandc, NAND_ADDR0, page << 16 | column); + nandc_set_reg(nandc, NAND_ADDR1, page >> 16 & 0xff); +} + +/* + * update_rw_regs: set up read/write register values, these will be + * written to the NAND controller registers via DMA + * + * @num_cw: number of steps for the read/write operation + * @read: read or write operation + */ +static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read) +{ + struct nand_chip *chip = &host->chip; + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + u32 cmd, cfg0, cfg1, ecc_bch_cfg; + + if (read) { + if (host->use_ecc) + cmd = PAGE_READ_WITH_ECC | PAGE_ACC | LAST_PAGE; + else + cmd = PAGE_READ | PAGE_ACC | LAST_PAGE; + } else { + cmd = PROGRAM_PAGE | PAGE_ACC | LAST_PAGE; + } + + if (host->use_ecc) { + cfg0 = (host->cfg0 & ~(7U << CW_PER_PAGE)) | + (num_cw - 1) << CW_PER_PAGE; + + cfg1 = host->cfg1; + ecc_bch_cfg = host->ecc_bch_cfg; + } else { + cfg0 = (host->cfg0_raw & ~(7U << CW_PER_PAGE)) | + (num_cw - 1) << CW_PER_PAGE; + + cfg1 = host->cfg1_raw; + ecc_bch_cfg = 1 << ECC_CFG_ECC_DISABLE; + } + + nandc_set_reg(nandc, NAND_FLASH_CMD, cmd); + nandc_set_reg(nandc, NAND_DEV0_CFG0, cfg0); + nandc_set_reg(nandc, NAND_DEV0_CFG1, cfg1); + nandc_set_reg(nandc, NAND_DEV0_ECC_CFG, ecc_bch_cfg); + nandc_set_reg(nandc, NAND_EBI2_ECC_BUF_CFG, host->ecc_buf_cfg); + nandc_set_reg(nandc, NAND_FLASH_STATUS, host->clrflashstatus); + nandc_set_reg(nandc, NAND_READ_STATUS, host->clrreadstatus); + nandc_set_reg(nandc, NAND_EXEC_CMD, 1); +} + +static int prep_dma_desc(struct qcom_nand_controller *nandc, bool read, + int reg_off, const void *vaddr, int size, + bool flow_control) +{ + struct desc_info *desc; + struct dma_async_tx_descriptor *dma_desc; + struct scatterlist *sgl; + struct dma_slave_config slave_conf; + enum dma_transfer_direction dir_eng; + int ret; + + desc = kzalloc(sizeof(*desc), GFP_KERNEL); + if (!desc) + return -ENOMEM; + + sgl = &desc->sgl; + + sg_init_one(sgl, vaddr, size); + + if (read) { + dir_eng = DMA_DEV_TO_MEM; + desc->dir = DMA_FROM_DEVICE; + } else { + dir_eng = DMA_MEM_TO_DEV; + desc->dir = DMA_TO_DEVICE; + } + + ret = dma_map_sg(nandc->dev, sgl, 1, desc->dir); + if (ret == 0) { + ret = -ENOMEM; + goto err; + } + + memset(&slave_conf, 0x00, sizeof(slave_conf)); + + slave_conf.device_fc = flow_control; + if (read) { + slave_conf.src_maxburst = 16; + slave_conf.src_addr = nandc->base_dma + reg_off; + slave_conf.slave_id = nandc->data_crci; + } else { + slave_conf.dst_maxburst = 16; + slave_conf.dst_addr = nandc->base_dma + reg_off; + slave_conf.slave_id = nandc->cmd_crci; + } + + ret = dmaengine_slave_config(nandc->chan, &slave_conf); + if (ret) { + dev_err(nandc->dev, "failed to configure dma channel\n"); + goto err; + } + + dma_desc = dmaengine_prep_slave_sg(nandc->chan, sgl, 1, dir_eng, 0); + if (!dma_desc) { + dev_err(nandc->dev, "failed to prepare desc\n"); + ret = -EINVAL; + goto err; + } + + desc->dma_desc = dma_desc; + + list_add_tail(&desc->node, &nandc->desc_list); + + return 0; +err: + kfree(desc); + + return ret; +} + +/* + * read_reg_dma: prepares a descriptor to read a given number of + * contiguous registers to the reg_read_buf pointer + * + * @first: offset of the first register in the contiguous block + * @num_regs: number of registers to read + */ +static int read_reg_dma(struct qcom_nand_controller *nandc, int first, + int num_regs) +{ + bool flow_control = false; + void *vaddr; + int size; + + if (first == NAND_READ_ID || first == NAND_FLASH_STATUS) + flow_control = true; + + size = num_regs * sizeof(u32); + vaddr = nandc->reg_read_buf + nandc->reg_read_pos; + nandc->reg_read_pos += num_regs; + + return prep_dma_desc(nandc, true, first, vaddr, size, flow_control); +} + +/* + * write_reg_dma: prepares a descriptor to write a given number of + * contiguous registers + * + * @first: offset of the first register in the contiguous block + * @num_regs: number of registers to write + */ +static int write_reg_dma(struct qcom_nand_controller *nandc, int first, + int num_regs) +{ + bool flow_control = false; + struct nandc_regs *regs = nandc->regs; + void *vaddr; + int size; + + vaddr = offset_to_nandc_reg(regs, first); + + if (first == NAND_FLASH_CMD) + flow_control = true; + + if (first == NAND_DEV_CMD1_RESTORE) + first = NAND_DEV_CMD1; + + if (first == NAND_DEV_CMD_VLD_RESTORE) + first = NAND_DEV_CMD_VLD; + + size = num_regs * sizeof(u32); + + return prep_dma_desc(nandc, false, first, vaddr, size, flow_control); +} + +/* + * read_data_dma: prepares a DMA descriptor to transfer data from the + * controller's internal buffer to the buffer 'vaddr' + * + * @reg_off: offset within the controller's data buffer + * @vaddr: virtual address of the buffer we want to write to + * @size: DMA transaction size in bytes + */ +static int read_data_dma(struct qcom_nand_controller *nandc, int reg_off, + const u8 *vaddr, int size) +{ + return prep_dma_desc(nandc, true, reg_off, vaddr, size, false); +} + +/* + * write_data_dma: prepares a DMA descriptor to transfer data from + * 'vaddr' to the controller's internal buffer + * + * @reg_off: offset within the controller's data buffer + * @vaddr: virtual address of the buffer we want to read from + * @size: DMA transaction size in bytes + */ +static int write_data_dma(struct qcom_nand_controller *nandc, int reg_off, + const u8 *vaddr, int size) +{ + return prep_dma_desc(nandc, false, reg_off, vaddr, size, false); +} + +/* + * helper to prepare dma descriptors to configure registers needed for reading a + * codeword/step in a page + */ +static void config_cw_read(struct qcom_nand_controller *nandc) +{ + write_reg_dma(nandc, NAND_FLASH_CMD, 3); + write_reg_dma(nandc, NAND_DEV0_CFG0, 3); + write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1); + + write_reg_dma(nandc, NAND_EXEC_CMD, 1); + + read_reg_dma(nandc, NAND_FLASH_STATUS, 2); + read_reg_dma(nandc, NAND_ERASED_CW_DETECT_STATUS, 1); +} + +/* + * helpers to prepare dma descriptors used to configure registers needed for + * writing a codeword/step in a page + */ +static void config_cw_write_pre(struct qcom_nand_controller *nandc) +{ + write_reg_dma(nandc, NAND_FLASH_CMD, 3); + write_reg_dma(nandc, NAND_DEV0_CFG0, 3); + write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1); +} + +static void config_cw_write_post(struct qcom_nand_controller *nandc) +{ + write_reg_dma(nandc, NAND_EXEC_CMD, 1); + + read_reg_dma(nandc, NAND_FLASH_STATUS, 1); + + write_reg_dma(nandc, NAND_FLASH_STATUS, 1); + write_reg_dma(nandc, NAND_READ_STATUS, 1); +} + +/* + * the following functions are used within chip->cmdfunc() to perform different + * NAND_CMD_* commands + */ + +/* sets up descriptors for NAND_CMD_PARAM */ +static int nandc_param(struct qcom_nand_host *host) +{ + struct nand_chip *chip = &host->chip; + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + + /* + * NAND_CMD_PARAM is called before we know much about the FLASH chip + * in use. we configure the controller to perform a raw read of 512 + * bytes to read onfi params + */ + nandc_set_reg(nandc, NAND_FLASH_CMD, PAGE_READ | PAGE_ACC | LAST_PAGE); + nandc_set_reg(nandc, NAND_ADDR0, 0); + nandc_set_reg(nandc, NAND_ADDR1, 0); + nandc_set_reg(nandc, NAND_DEV0_CFG0, 0 << CW_PER_PAGE + | 512 << UD_SIZE_BYTES + | 5 << NUM_ADDR_CYCLES + | 0 << SPARE_SIZE_BYTES); + nandc_set_reg(nandc, NAND_DEV0_CFG1, 7 << NAND_RECOVERY_CYCLES + | 0 << CS_ACTIVE_BSY + | 17 << BAD_BLOCK_BYTE_NUM + | 1 << BAD_BLOCK_IN_SPARE_AREA + | 2 << WR_RD_BSY_GAP + | 0 << WIDE_FLASH + | 1 << DEV0_CFG1_ECC_DISABLE); + nandc_set_reg(nandc, NAND_EBI2_ECC_BUF_CFG, 1 << ECC_CFG_ECC_DISABLE); + + /* configure CMD1 and VLD for ONFI param probing */ + nandc_set_reg(nandc, NAND_DEV_CMD_VLD, + (nandc->vld & ~(1 << READ_START_VLD)) + | 0 << READ_START_VLD); + nandc_set_reg(nandc, NAND_DEV_CMD1, + (nandc->cmd1 & ~(0xFF << READ_ADDR)) + | NAND_CMD_PARAM << READ_ADDR); + + nandc_set_reg(nandc, NAND_EXEC_CMD, 1); + + nandc_set_reg(nandc, NAND_DEV_CMD1_RESTORE, nandc->cmd1); + nandc_set_reg(nandc, NAND_DEV_CMD_VLD_RESTORE, nandc->vld); + + write_reg_dma(nandc, NAND_DEV_CMD_VLD, 1); + write_reg_dma(nandc, NAND_DEV_CMD1, 1); + + nandc->buf_count = 512; + memset(nandc->data_buffer, 0xff, nandc->buf_count); + + config_cw_read(nandc); + + read_data_dma(nandc, FLASH_BUF_ACC, nandc->data_buffer, + nandc->buf_count); + + /* restore CMD1 and VLD regs */ + write_reg_dma(nandc, NAND_DEV_CMD1_RESTORE, 1); + write_reg_dma(nandc, NAND_DEV_CMD_VLD_RESTORE, 1); + + return 0; +} + +/* sets up descriptors for NAND_CMD_ERASE1 */ +static int erase_block(struct qcom_nand_host *host, int page_addr) +{ + struct nand_chip *chip = &host->chip; + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + + nandc_set_reg(nandc, NAND_FLASH_CMD, + BLOCK_ERASE | PAGE_ACC | LAST_PAGE); + nandc_set_reg(nandc, NAND_ADDR0, page_addr); + nandc_set_reg(nandc, NAND_ADDR1, 0); + nandc_set_reg(nandc, NAND_DEV0_CFG0, + host->cfg0_raw & ~(7 << CW_PER_PAGE)); + nandc_set_reg(nandc, NAND_DEV0_CFG1, host->cfg1_raw); + nandc_set_reg(nandc, NAND_EXEC_CMD, 1); + nandc_set_reg(nandc, NAND_FLASH_STATUS, host->clrflashstatus); + nandc_set_reg(nandc, NAND_READ_STATUS, host->clrreadstatus); + + write_reg_dma(nandc, NAND_FLASH_CMD, 3); + write_reg_dma(nandc, NAND_DEV0_CFG0, 2); + write_reg_dma(nandc, NAND_EXEC_CMD, 1); + + read_reg_dma(nandc, NAND_FLASH_STATUS, 1); + + write_reg_dma(nandc, NAND_FLASH_STATUS, 1); + write_reg_dma(nandc, NAND_READ_STATUS, 1); + + return 0; +} + +/* sets up descriptors for NAND_CMD_READID */ +static int read_id(struct qcom_nand_host *host, int column) +{ + struct nand_chip *chip = &host->chip; + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + + if (column == -1) + return 0; + + nandc_set_reg(nandc, NAND_FLASH_CMD, FETCH_ID); + nandc_set_reg(nandc, NAND_ADDR0, column); + nandc_set_reg(nandc, NAND_ADDR1, 0); + nandc_set_reg(nandc, NAND_FLASH_CHIP_SELECT, DM_EN); + nandc_set_reg(nandc, NAND_EXEC_CMD, 1); + + write_reg_dma(nandc, NAND_FLASH_CMD, 4); + write_reg_dma(nandc, NAND_EXEC_CMD, 1); + + read_reg_dma(nandc, NAND_READ_ID, 1); + + return 0; +} + +/* sets up descriptors for NAND_CMD_RESET */ +static int reset(struct qcom_nand_host *host) +{ + struct nand_chip *chip = &host->chip; + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + + nandc_set_reg(nandc, NAND_FLASH_CMD, RESET_DEVICE); + nandc_set_reg(nandc, NAND_EXEC_CMD, 1); + + write_reg_dma(nandc, NAND_FLASH_CMD, 1); + write_reg_dma(nandc, NAND_EXEC_CMD, 1); + + read_reg_dma(nandc, NAND_FLASH_STATUS, 1); + + return 0; +} + +/* helpers to submit/free our list of dma descriptors */ +static int submit_descs(struct qcom_nand_controller *nandc) +{ + struct desc_info *desc; + dma_cookie_t cookie = 0; + + list_for_each_entry(desc, &nandc->desc_list, node) + cookie = dmaengine_submit(desc->dma_desc); + + if (dma_sync_wait(nandc->chan, cookie) != DMA_COMPLETE) + return -ETIMEDOUT; + + return 0; +} + +static void free_descs(struct qcom_nand_controller *nandc) +{ + struct desc_info *desc, *n; + + list_for_each_entry_safe(desc, n, &nandc->desc_list, node) { + list_del(&desc->node); + dma_unmap_sg(nandc->dev, &desc->sgl, 1, desc->dir); + kfree(desc); + } +} + +/* reset the register read buffer for next NAND operation */ +static void clear_read_regs(struct qcom_nand_controller *nandc) +{ + nandc->reg_read_pos = 0; + memset(nandc->reg_read_buf, 0, + MAX_REG_RD * sizeof(*nandc->reg_read_buf)); +} + +static void pre_command(struct qcom_nand_host *host, int command) +{ + struct nand_chip *chip = &host->chip; + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + + nandc->buf_count = 0; + nandc->buf_start = 0; + host->use_ecc = false; + host->last_command = command; + + clear_read_regs(nandc); +} + +/* + * this is called after NAND_CMD_PAGEPROG and NAND_CMD_ERASE1 to set our + * privately maintained status byte, this status byte can be read after + * NAND_CMD_STATUS is called + */ +static void parse_erase_write_errors(struct qcom_nand_host *host, int command) +{ + struct nand_chip *chip = &host->chip; + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + struct nand_ecc_ctrl *ecc = &chip->ecc; + int num_cw; + int i; + + num_cw = command == NAND_CMD_PAGEPROG ? ecc->steps : 1; + + for (i = 0; i < num_cw; i++) { + u32 flash_status = le32_to_cpu(nandc->reg_read_buf[i]); + + if (flash_status & FS_MPU_ERR) + host->status &= ~NAND_STATUS_WP; + + if (flash_status & FS_OP_ERR || (i == (num_cw - 1) && + (flash_status & + FS_DEVICE_STS_ERR))) + host->status |= NAND_STATUS_FAIL; + } +} + +static void post_command(struct qcom_nand_host *host, int command) +{ + struct nand_chip *chip = &host->chip; + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + + switch (command) { + case NAND_CMD_READID: + memcpy(nandc->data_buffer, nandc->reg_read_buf, + nandc->buf_count); + break; + case NAND_CMD_PAGEPROG: + case NAND_CMD_ERASE1: + parse_erase_write_errors(host, command); + break; + default: + break; + } +} + +/* + * Implements chip->cmdfunc. It's only used for a limited set of commands. + * The rest of the commands wouldn't be called by upper layers. For example, + * NAND_CMD_READOOB would never be called because we have our own versions + * of read_oob ops for nand_ecc_ctrl. + */ +static void qcom_nandc_command(struct mtd_info *mtd, unsigned int command, + int column, int page_addr) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct qcom_nand_host *host = to_qcom_nand_host(chip); + struct nand_ecc_ctrl *ecc = &chip->ecc; + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + bool wait = false; + int ret = 0; + + pre_command(host, command); + + switch (command) { + case NAND_CMD_RESET: + ret = reset(host); + wait = true; + break; + + case NAND_CMD_READID: + nandc->buf_count = 4; + ret = read_id(host, column); + wait = true; + break; + + case NAND_CMD_PARAM: + ret = nandc_param(host); + wait = true; + break; + + case NAND_CMD_ERASE1: + ret = erase_block(host, page_addr); + wait = true; + break; + + case NAND_CMD_READ0: + /* we read the entire page for now */ + WARN_ON(column != 0); + + host->use_ecc = true; + set_address(host, 0, page_addr); + update_rw_regs(host, ecc->steps, true); + break; + + case NAND_CMD_SEQIN: + WARN_ON(column != 0); + set_address(host, 0, page_addr); + break; + + case NAND_CMD_PAGEPROG: + case NAND_CMD_STATUS: + case NAND_CMD_NONE: + default: + break; + } + + if (ret) { + dev_err(nandc->dev, "failure executing command %d\n", + command); + free_descs(nandc); + return; + } + + if (wait) { + ret = submit_descs(nandc); + if (ret) + dev_err(nandc->dev, + "failure submitting descs for command %d\n", + command); + } + + free_descs(nandc); + + post_command(host, command); +} + +/* + * when using BCH ECC, the HW flags an error in NAND_FLASH_STATUS if it read + * an erased CW, and reports an erased CW in NAND_ERASED_CW_DETECT_STATUS. + * + * when using RS ECC, the HW reports the same erros when reading an erased CW, + * but it notifies that it is an erased CW by placing special characters at + * certain offsets in the buffer. + * + * verify if the page is erased or not, and fix up the page for RS ECC by + * replacing the special characters with 0xff. + */ +static bool erased_chunk_check_and_fixup(u8 *data_buf, int data_len) +{ + u8 empty1, empty2; + + /* + * an erased page flags an error in NAND_FLASH_STATUS, check if the page + * is erased by looking for 0x54s at offsets 3 and 175 from the + * beginning of each codeword + */ + + empty1 = data_buf[3]; + empty2 = data_buf[175]; + + /* + * if the erased codework markers, if they exist override them with + * 0xffs + */ + if ((empty1 == 0x54 && empty2 == 0xff) || + (empty1 == 0xff && empty2 == 0x54)) { + data_buf[3] = 0xff; + data_buf[175] = 0xff; + } + + /* + * check if the entire chunk contains 0xffs or not. if it doesn't, then + * restore the original values at the special offsets + */ + if (memchr_inv(data_buf, 0xff, data_len)) { + data_buf[3] = empty1; + data_buf[175] = empty2; + + return false; + } + + return true; +} + +struct read_stats { + __le32 flash; + __le32 buffer; + __le32 erased_cw; +}; + +/* + * reads back status registers set by the controller to notify page read + * errors. this is equivalent to what 'ecc->correct()' would do. + */ +static int parse_read_errors(struct qcom_nand_host *host, u8 *data_buf, + u8 *oob_buf) +{ + struct nand_chip *chip = &host->chip; + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + struct mtd_info *mtd = nand_to_mtd(chip); + struct nand_ecc_ctrl *ecc = &chip->ecc; + unsigned int max_bitflips = 0; + struct read_stats *buf; + int i; + + buf = (struct read_stats *)nandc->reg_read_buf; + + for (i = 0; i < ecc->steps; i++, buf++) { + u32 flash, buffer, erased_cw; + int data_len, oob_len; + + if (i == (ecc->steps - 1)) { + data_len = ecc->size - ((ecc->steps - 1) << 2); + oob_len = ecc->steps << 2; + } else { + data_len = host->cw_data; + oob_len = 0; + } + + flash = le32_to_cpu(buf->flash); + buffer = le32_to_cpu(buf->buffer); + erased_cw = le32_to_cpu(buf->erased_cw); + + if (flash & (FS_OP_ERR | FS_MPU_ERR)) { + bool erased; + + /* ignore erased codeword errors */ + if (host->bch_enabled) { + erased = (erased_cw & ERASED_CW) == ERASED_CW ? + true : false; + } else { + erased = erased_chunk_check_and_fixup(data_buf, + data_len); + } + + if (erased) { + data_buf += data_len; + if (oob_buf) + oob_buf += oob_len + ecc->bytes; + continue; + } + + if (buffer & BS_UNCORRECTABLE_BIT) { + int ret, ecclen, extraooblen; + void *eccbuf; + + eccbuf = oob_buf ? oob_buf + oob_len : NULL; + ecclen = oob_buf ? host->ecc_bytes_hw : 0; + extraooblen = oob_buf ? oob_len : 0; + + /* + * make sure it isn't an erased page reported + * as not-erased by HW because of a few bitflips + */ + ret = nand_check_erased_ecc_chunk(data_buf, + data_len, eccbuf, ecclen, oob_buf, + extraooblen, ecc->strength); + if (ret < 0) { + mtd->ecc_stats.failed++; + } else { + mtd->ecc_stats.corrected += ret; + max_bitflips = + max_t(unsigned int, max_bitflips, ret); + } + } + } else { + unsigned int stat; + + stat = buffer & BS_CORRECTABLE_ERR_MSK; + mtd->ecc_stats.corrected += stat; + max_bitflips = max(max_bitflips, stat); + } + + data_buf += data_len; + if (oob_buf) + oob_buf += oob_len + ecc->bytes; + } + + return max_bitflips; +} + +/* + * helper to perform the actual page read operation, used by ecc->read_page(), + * ecc->read_oob() + */ +static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf, + u8 *oob_buf) +{ + struct nand_chip *chip = &host->chip; + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + struct nand_ecc_ctrl *ecc = &chip->ecc; + int i, ret; + + /* queue cmd descs for each codeword */ + for (i = 0; i < ecc->steps; i++) { + int data_size, oob_size; + + if (i == (ecc->steps - 1)) { + data_size = ecc->size - ((ecc->steps - 1) << 2); + oob_size = (ecc->steps << 2) + host->ecc_bytes_hw + + host->spare_bytes; + } else { + data_size = host->cw_data; + oob_size = host->ecc_bytes_hw + host->spare_bytes; + } + + config_cw_read(nandc); + + if (data_buf) + read_data_dma(nandc, FLASH_BUF_ACC, data_buf, + data_size); + + /* + * when ecc is enabled, the controller doesn't read the real + * or dummy bad block markers in each chunk. To maintain a + * consistent layout across RAW and ECC reads, we just + * leave the real/dummy BBM offsets empty (i.e, filled with + * 0xffs) + */ + if (oob_buf) { + int j; + + for (j = 0; j < host->bbm_size; j++) + *oob_buf++ = 0xff; + + read_data_dma(nandc, FLASH_BUF_ACC + data_size, + oob_buf, oob_size); + } + + if (data_buf) + data_buf += data_size; + if (oob_buf) + oob_buf += oob_size; + } + + ret = submit_descs(nandc); + if (ret) + dev_err(nandc->dev, "failure to read page/oob\n"); + + free_descs(nandc); + + return ret; +} + +/* + * a helper that copies the last step/codeword of a page (containing free oob) + * into our local buffer + */ +static int copy_last_cw(struct qcom_nand_host *host, int page) +{ + struct nand_chip *chip = &host->chip; + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + struct nand_ecc_ctrl *ecc = &chip->ecc; + int size; + int ret; + + clear_read_regs(nandc); + + size = host->use_ecc ? host->cw_data : host->cw_size; + + /* prepare a clean read buffer */ + memset(nandc->data_buffer, 0xff, size); + + set_address(host, host->cw_size * (ecc->steps - 1), page); + update_rw_regs(host, 1, true); + + config_cw_read(nandc); + + read_data_dma(nandc, FLASH_BUF_ACC, nandc->data_buffer, size); + + ret = submit_descs(nandc); + if (ret) + dev_err(nandc->dev, "failed to copy last codeword\n"); + + free_descs(nandc); + + return ret; +} + +/* implements ecc->read_page() */ +static int qcom_nandc_read_page(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + struct qcom_nand_host *host = to_qcom_nand_host(chip); + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + u8 *data_buf, *oob_buf = NULL; + int ret; + + data_buf = buf; + oob_buf = oob_required ? chip->oob_poi : NULL; + + ret = read_page_ecc(host, data_buf, oob_buf); + if (ret) { + dev_err(nandc->dev, "failure to read page\n"); + return ret; + } + + return parse_read_errors(host, data_buf, oob_buf); +} + +/* implements ecc->read_page_raw() */ +static int qcom_nandc_read_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, uint8_t *buf, + int oob_required, int page) +{ + struct qcom_nand_host *host = to_qcom_nand_host(chip); + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + u8 *data_buf, *oob_buf; + struct nand_ecc_ctrl *ecc = &chip->ecc; + int i, ret; + + data_buf = buf; + oob_buf = chip->oob_poi; + + host->use_ecc = false; + update_rw_regs(host, ecc->steps, true); + + for (i = 0; i < ecc->steps; i++) { + int data_size1, data_size2, oob_size1, oob_size2; + int reg_off = FLASH_BUF_ACC; + + data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1); + oob_size1 = host->bbm_size; + + if (i == (ecc->steps - 1)) { + data_size2 = ecc->size - data_size1 - + ((ecc->steps - 1) << 2); + oob_size2 = (ecc->steps << 2) + host->ecc_bytes_hw + + host->spare_bytes; + } else { + data_size2 = host->cw_data - data_size1; + oob_size2 = host->ecc_bytes_hw + host->spare_bytes; + } + + config_cw_read(nandc); + + read_data_dma(nandc, reg_off, data_buf, data_size1); + reg_off += data_size1; + data_buf += data_size1; + + read_data_dma(nandc, reg_off, oob_buf, oob_size1); + reg_off += oob_size1; + oob_buf += oob_size1; + + read_data_dma(nandc, reg_off, data_buf, data_size2); + reg_off += data_size2; + data_buf += data_size2; + + read_data_dma(nandc, reg_off, oob_buf, oob_size2); + oob_buf += oob_size2; + } + + ret = submit_descs(nandc); + if (ret) + dev_err(nandc->dev, "failure to read raw page\n"); + + free_descs(nandc); + + return 0; +} + +/* implements ecc->read_oob() */ +static int qcom_nandc_read_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + struct qcom_nand_host *host = to_qcom_nand_host(chip); + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + struct nand_ecc_ctrl *ecc = &chip->ecc; + int ret; + + clear_read_regs(nandc); + + host->use_ecc = true; + set_address(host, 0, page); + update_rw_regs(host, ecc->steps, true); + + ret = read_page_ecc(host, NULL, chip->oob_poi); + if (ret) + dev_err(nandc->dev, "failure to read oob\n"); + + return ret; +} + +/* implements ecc->write_page() */ +static int qcom_nandc_write_page(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int oob_required, int page) +{ + struct qcom_nand_host *host = to_qcom_nand_host(chip); + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + struct nand_ecc_ctrl *ecc = &chip->ecc; + u8 *data_buf, *oob_buf; + int i, ret; + + clear_read_regs(nandc); + + data_buf = (u8 *)buf; + oob_buf = chip->oob_poi; + + host->use_ecc = true; + update_rw_regs(host, ecc->steps, false); + + for (i = 0; i < ecc->steps; i++) { + int data_size, oob_size; + + if (i == (ecc->steps - 1)) { + data_size = ecc->size - ((ecc->steps - 1) << 2); + oob_size = (ecc->steps << 2) + host->ecc_bytes_hw + + host->spare_bytes; + } else { + data_size = host->cw_data; + oob_size = ecc->bytes; + } + + config_cw_write_pre(nandc); + + write_data_dma(nandc, FLASH_BUF_ACC, data_buf, data_size); + + /* + * when ECC is enabled, we don't really need to write anything + * to oob for the first n - 1 codewords since these oob regions + * just contain ECC bytes that's written by the controller + * itself. For the last codeword, we skip the bbm positions and + * write to the free oob area. + */ + if (i == (ecc->steps - 1)) { + oob_buf += host->bbm_size; + + write_data_dma(nandc, FLASH_BUF_ACC + data_size, + oob_buf, oob_size); + } + + config_cw_write_post(nandc); + + data_buf += data_size; + oob_buf += oob_size; + } + + ret = submit_descs(nandc); + if (ret) + dev_err(nandc->dev, "failure to write page\n"); + + free_descs(nandc); + + return ret; +} + +/* implements ecc->write_page_raw() */ +static int qcom_nandc_write_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, const uint8_t *buf, + int oob_required, int page) +{ + struct qcom_nand_host *host = to_qcom_nand_host(chip); + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + struct nand_ecc_ctrl *ecc = &chip->ecc; + u8 *data_buf, *oob_buf; + int i, ret; + + clear_read_regs(nandc); + + data_buf = (u8 *)buf; + oob_buf = chip->oob_poi; + + host->use_ecc = false; + update_rw_regs(host, ecc->steps, false); + + for (i = 0; i < ecc->steps; i++) { + int data_size1, data_size2, oob_size1, oob_size2; + int reg_off = FLASH_BUF_ACC; + + data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1); + oob_size1 = host->bbm_size; + + if (i == (ecc->steps - 1)) { + data_size2 = ecc->size - data_size1 - + ((ecc->steps - 1) << 2); + oob_size2 = (ecc->steps << 2) + host->ecc_bytes_hw + + host->spare_bytes; + } else { + data_size2 = host->cw_data - data_size1; + oob_size2 = host->ecc_bytes_hw + host->spare_bytes; + } + + config_cw_write_pre(nandc); + + write_data_dma(nandc, reg_off, data_buf, data_size1); + reg_off += data_size1; + data_buf += data_size1; + + write_data_dma(nandc, reg_off, oob_buf, oob_size1); + reg_off += oob_size1; + oob_buf += oob_size1; + + write_data_dma(nandc, reg_off, data_buf, data_size2); + reg_off += data_size2; + data_buf += data_size2; + + write_data_dma(nandc, reg_off, oob_buf, oob_size2); + oob_buf += oob_size2; + + config_cw_write_post(nandc); + } + + ret = submit_descs(nandc); + if (ret) + dev_err(nandc->dev, "failure to write raw page\n"); + + free_descs(nandc); + + return ret; +} + +/* + * implements ecc->write_oob() + * + * the NAND controller cannot write only data or only oob within a codeword, + * since ecc is calculated for the combined codeword. we first copy the + * entire contents for the last codeword(data + oob), replace the old oob + * with the new one in chip->oob_poi, and then write the entire codeword. + * this read-copy-write operation results in a slight performance loss. + */ +static int qcom_nandc_write_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + struct qcom_nand_host *host = to_qcom_nand_host(chip); + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + struct nand_ecc_ctrl *ecc = &chip->ecc; + u8 *oob = chip->oob_poi; + int free_boff; + int data_size, oob_size; + int ret, status = 0; + + host->use_ecc = true; + + ret = copy_last_cw(host, page); + if (ret) + return ret; + + clear_read_regs(nandc); + + /* calculate the data and oob size for the last codeword/step */ + data_size = ecc->size - ((ecc->steps - 1) << 2); + oob_size = ecc->steps << 2; + + free_boff = ecc->layout->oobfree[0].offset; + + /* override new oob content to last codeword */ + memcpy(nandc->data_buffer + data_size, oob + free_boff, oob_size); + + set_address(host, host->cw_size * (ecc->steps - 1), page); + update_rw_regs(host, 1, false); + + config_cw_write_pre(nandc); + write_data_dma(nandc, FLASH_BUF_ACC, nandc->data_buffer, + data_size + oob_size); + config_cw_write_post(nandc); + + ret = submit_descs(nandc); + + free_descs(nandc); + + if (ret) { + dev_err(nandc->dev, "failure to write oob\n"); + return -EIO; + } + + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + + status = chip->waitfunc(mtd, chip); + + return status & NAND_STATUS_FAIL ? -EIO : 0; +} + +static int qcom_nandc_block_bad(struct mtd_info *mtd, loff_t ofs) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct qcom_nand_host *host = to_qcom_nand_host(chip); + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + struct nand_ecc_ctrl *ecc = &chip->ecc; + int page, ret, bbpos, bad = 0; + u32 flash_status; + + page = (int)(ofs >> chip->page_shift) & chip->pagemask; + + /* + * configure registers for a raw sub page read, the address is set to + * the beginning of the last codeword, we don't care about reading ecc + * portion of oob. we just want the first few bytes from this codeword + * that contains the BBM + */ + host->use_ecc = false; + + ret = copy_last_cw(host, page); + if (ret) + goto err; + + flash_status = le32_to_cpu(nandc->reg_read_buf[0]); + + if (flash_status & (FS_OP_ERR | FS_MPU_ERR)) { + dev_warn(nandc->dev, "error when trying to read BBM\n"); + goto err; + } + + bbpos = mtd->writesize - host->cw_size * (ecc->steps - 1); + + bad = nandc->data_buffer[bbpos] != 0xff; + + if (chip->options & NAND_BUSWIDTH_16) + bad = bad || (nandc->data_buffer[bbpos + 1] != 0xff); +err: + return bad; +} + +static int qcom_nandc_block_markbad(struct mtd_info *mtd, loff_t ofs) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct qcom_nand_host *host = to_qcom_nand_host(chip); + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + struct nand_ecc_ctrl *ecc = &chip->ecc; + int page, ret, status = 0; + + clear_read_regs(nandc); + + /* + * to mark the BBM as bad, we flash the entire last codeword with 0s. + * we don't care about the rest of the content in the codeword since + * we aren't going to use this block again + */ + memset(nandc->data_buffer, 0x00, host->cw_size); + + page = (int)(ofs >> chip->page_shift) & chip->pagemask; + + /* prepare write */ + host->use_ecc = false; + set_address(host, host->cw_size * (ecc->steps - 1), page); + update_rw_regs(host, 1, false); + + config_cw_write_pre(nandc); + write_data_dma(nandc, FLASH_BUF_ACC, nandc->data_buffer, host->cw_size); + config_cw_write_post(nandc); + + ret = submit_descs(nandc); + + free_descs(nandc); + + if (ret) { + dev_err(nandc->dev, "failure to update BBM\n"); + return -EIO; + } + + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + + status = chip->waitfunc(mtd, chip); + + return status & NAND_STATUS_FAIL ? -EIO : 0; +} + +/* + * the three functions below implement chip->read_byte(), chip->read_buf() + * and chip->write_buf() respectively. these aren't used for + * reading/writing page data, they are used for smaller data like reading + * id, status etc + */ +static uint8_t qcom_nandc_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct qcom_nand_host *host = to_qcom_nand_host(chip); + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + u8 *buf = nandc->data_buffer; + u8 ret = 0x0; + + if (host->last_command == NAND_CMD_STATUS) { + ret = host->status; + + host->status = NAND_STATUS_READY | NAND_STATUS_WP; + + return ret; + } + + if (nandc->buf_start < nandc->buf_count) + ret = buf[nandc->buf_start++]; + + return ret; +} + +static void qcom_nandc_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + int real_len = min_t(size_t, len, nandc->buf_count - nandc->buf_start); + + memcpy(buf, nandc->data_buffer + nandc->buf_start, real_len); + nandc->buf_start += real_len; +} + +static void qcom_nandc_write_buf(struct mtd_info *mtd, const uint8_t *buf, + int len) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + int real_len = min_t(size_t, len, nandc->buf_count - nandc->buf_start); + + memcpy(nandc->data_buffer + nandc->buf_start, buf, real_len); + + nandc->buf_start += real_len; +} + +/* we support only one external chip for now */ +static void qcom_nandc_select_chip(struct mtd_info *mtd, int chipnr) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + + if (chipnr <= 0) + return; + + dev_warn(nandc->dev, "invalid chip select\n"); +} + +/* + * NAND controller page layout info + * + * Layout with ECC enabled: + * + * |----------------------| |---------------------------------| + * | xx.......yy| | *********xx.......yy| + * | DATA xx..ECC..yy| | DATA **SPARE**xx..ECC..yy| + * | (516) xx.......yy| | (516-n*4) **(n*4)**xx.......yy| + * | xx.......yy| | *********xx.......yy| + * |----------------------| |---------------------------------| + * codeword 1,2..n-1 codeword n + * <---(528/532 Bytes)--> <-------(528/532 Bytes)---------> + * + * n = Number of codewords in the page + * . = ECC bytes + * * = Spare/free bytes + * x = Unused byte(s) + * y = Reserved byte(s) + * + * 2K page: n = 4, spare = 16 bytes + * 4K page: n = 8, spare = 32 bytes + * 8K page: n = 16, spare = 64 bytes + * + * the qcom nand controller operates at a sub page/codeword level. each + * codeword is 528 and 532 bytes for 4 bit and 8 bit ECC modes respectively. + * the number of ECC bytes vary based on the ECC strength and the bus width. + * + * the first n - 1 codewords contains 516 bytes of user data, the remaining + * 12/16 bytes consist of ECC and reserved data. The nth codeword contains + * both user data and spare(oobavail) bytes that sum up to 516 bytes. + * + * When we access a page with ECC enabled, the reserved bytes(s) are not + * accessible at all. When reading, we fill up these unreadable positions + * with 0xffs. When writing, the controller skips writing the inaccessible + * bytes. + * + * Layout with ECC disabled: + * + * |------------------------------| |---------------------------------------| + * | yy xx.......| | bb *********xx.......| + * | DATA1 yy DATA2 xx..ECC..| | DATA1 bb DATA2 **SPARE**xx..ECC..| + * | (size1) yy (size2) xx.......| | (size1) bb (size2) **(n*4)**xx.......| + * | yy xx.......| | bb *********xx.......| + * |------------------------------| |---------------------------------------| + * codeword 1,2..n-1 codeword n + * <-------(528/532 Bytes)------> <-----------(528/532 Bytes)-----------> + * + * n = Number of codewords in the page + * . = ECC bytes + * * = Spare/free bytes + * x = Unused byte(s) + * y = Dummy Bad Bock byte(s) + * b = Real Bad Block byte(s) + * size1/size2 = function of codeword size and 'n' + * + * when the ECC block is disabled, one reserved byte (or two for 16 bit bus + * width) is now accessible. For the first n - 1 codewords, these are dummy Bad + * Block Markers. In the last codeword, this position contains the real BBM + * + * In order to have a consistent layout between RAW and ECC modes, we assume + * the following OOB layout arrangement: + * + * |-----------| |--------------------| + * |yyxx.......| |bb*********xx.......| + * |yyxx..ECC..| |bb*FREEOOB*xx..ECC..| + * |yyxx.......| |bb*********xx.......| + * |yyxx.......| |bb*********xx.......| + * |-----------| |--------------------| + * first n - 1 nth OOB region + * OOB regions + * + * n = Number of codewords in the page + * . = ECC bytes + * * = FREE OOB bytes + * y = Dummy bad block byte(s) (inaccessible when ECC enabled) + * x = Unused byte(s) + * b = Real bad block byte(s) (inaccessible when ECC enabled) + * + * This layout is read as is when ECC is disabled. When ECC is enabled, the + * inaccessible Bad Block byte(s) are ignored when we write to a page/oob, + * and assumed as 0xffs when we read a page/oob. The ECC, unused and + * dummy/real bad block bytes are grouped as ecc bytes in nand_ecclayout (i.e, + * ecc->bytes is the sum of the three). + */ + +static struct nand_ecclayout * +qcom_nand_create_layout(struct qcom_nand_host *host) +{ + struct nand_chip *chip = &host->chip; + struct mtd_info *mtd = nand_to_mtd(chip); + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + struct nand_ecc_ctrl *ecc = &chip->ecc; + struct nand_ecclayout *layout; + int i, j, steps, pos = 0, shift = 0; + + layout = devm_kzalloc(nandc->dev, sizeof(*layout), GFP_KERNEL); + if (!layout) + return NULL; + + steps = mtd->writesize / ecc->size; + layout->eccbytes = steps * ecc->bytes; + + layout->oobfree[0].offset = (steps - 1) * ecc->bytes + host->bbm_size; + layout->oobfree[0].length = steps << 2; + + /* + * the oob bytes in the first n - 1 codewords are all grouped together + * in the format: + * DUMMY_BBM + UNUSED + ECC + */ + for (i = 0; i < steps - 1; i++) { + for (j = 0; j < ecc->bytes; j++) + layout->eccpos[pos++] = i * ecc->bytes + j; + } + + /* + * the oob bytes in the last codeword are grouped in the format: + * BBM + FREE OOB + UNUSED + ECC + */ + + /* fill up the bbm positions */ + for (j = 0; j < host->bbm_size; j++) + layout->eccpos[pos++] = i * ecc->bytes + j; + + /* + * fill up the ecc and reserved positions, their indices are offseted + * by the free oob region + */ + shift = layout->oobfree[0].length + host->bbm_size; + + for (j = 0; j < (host->ecc_bytes_hw + host->spare_bytes); j++) + layout->eccpos[pos++] = i * ecc->bytes + shift + j; + + return layout; +} + +static int qcom_nand_host_setup(struct qcom_nand_host *host) +{ + struct nand_chip *chip = &host->chip; + struct mtd_info *mtd = nand_to_mtd(chip); + struct nand_ecc_ctrl *ecc = &chip->ecc; + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + int cwperpage, bad_block_byte; + bool wide_bus; + int ecc_mode = 1; + + /* + * the controller requires each step consists of 512 bytes of data. + * bail out if DT has populated a wrong step size. + */ + if (ecc->size != NANDC_STEP_SIZE) { + dev_err(nandc->dev, "invalid ecc size\n"); + return -EINVAL; + } + + wide_bus = chip->options & NAND_BUSWIDTH_16 ? true : false; + + if (ecc->strength >= 8) { + /* 8 bit ECC defaults to BCH ECC on all platforms */ + host->bch_enabled = true; + ecc_mode = 1; + + if (wide_bus) { + host->ecc_bytes_hw = 14; + host->spare_bytes = 0; + host->bbm_size = 2; + } else { + host->ecc_bytes_hw = 13; + host->spare_bytes = 2; + host->bbm_size = 1; + } + } else { + /* + * if the controller supports BCH for 4 bit ECC, the controller + * uses lesser bytes for ECC. If RS is used, the ECC bytes is + * always 10 bytes + */ + if (nandc->ecc_modes & ECC_BCH_4BIT) { + /* BCH */ + host->bch_enabled = true; + ecc_mode = 0; + + if (wide_bus) { + host->ecc_bytes_hw = 8; + host->spare_bytes = 2; + host->bbm_size = 2; + } else { + host->ecc_bytes_hw = 7; + host->spare_bytes = 4; + host->bbm_size = 1; + } + } else { + /* RS */ + host->ecc_bytes_hw = 10; + + if (wide_bus) { + host->spare_bytes = 0; + host->bbm_size = 2; + } else { + host->spare_bytes = 1; + host->bbm_size = 1; + } + } + } + + /* + * we consider ecc->bytes as the sum of all the non-data content in a + * step. It gives us a clean representation of the oob area (even if + * all the bytes aren't used for ECC).It is always 16 bytes for 8 bit + * ECC and 12 bytes for 4 bit ECC + */ + ecc->bytes = host->ecc_bytes_hw + host->spare_bytes + host->bbm_size; + + ecc->read_page = qcom_nandc_read_page; + ecc->read_page_raw = qcom_nandc_read_page_raw; + ecc->read_oob = qcom_nandc_read_oob; + ecc->write_page = qcom_nandc_write_page; + ecc->write_page_raw = qcom_nandc_write_page_raw; + ecc->write_oob = qcom_nandc_write_oob; + + ecc->mode = NAND_ECC_HW; + + ecc->layout = qcom_nand_create_layout(host); + if (!ecc->layout) + return -ENOMEM; + + cwperpage = mtd->writesize / ecc->size; + + /* + * DATA_UD_BYTES varies based on whether the read/write command protects + * spare data with ECC too. We protect spare data by default, so we set + * it to main + spare data, which are 512 and 4 bytes respectively. + */ + host->cw_data = 516; + + /* + * total bytes in a step, either 528 bytes for 4 bit ECC, or 532 bytes + * for 8 bit ECC + */ + host->cw_size = host->cw_data + ecc->bytes; + + if (ecc->bytes * (mtd->writesize / ecc->size) > mtd->oobsize) { + dev_err(nandc->dev, "ecc data doesn't fit in OOB area\n"); + return -EINVAL; + } + + bad_block_byte = mtd->writesize - host->cw_size * (cwperpage - 1) + 1; + + host->cfg0 = (cwperpage - 1) << CW_PER_PAGE + | host->cw_data << UD_SIZE_BYTES + | 0 << DISABLE_STATUS_AFTER_WRITE + | 5 << NUM_ADDR_CYCLES + | host->ecc_bytes_hw << ECC_PARITY_SIZE_BYTES_RS + | 0 << STATUS_BFR_READ + | 1 << SET_RD_MODE_AFTER_STATUS + | host->spare_bytes << SPARE_SIZE_BYTES; + + host->cfg1 = 7 << NAND_RECOVERY_CYCLES + | 0 << CS_ACTIVE_BSY + | bad_block_byte << BAD_BLOCK_BYTE_NUM + | 0 << BAD_BLOCK_IN_SPARE_AREA + | 2 << WR_RD_BSY_GAP + | wide_bus << WIDE_FLASH + | host->bch_enabled << ENABLE_BCH_ECC; + + host->cfg0_raw = (cwperpage - 1) << CW_PER_PAGE + | host->cw_size << UD_SIZE_BYTES + | 5 << NUM_ADDR_CYCLES + | 0 << SPARE_SIZE_BYTES; + + host->cfg1_raw = 7 << NAND_RECOVERY_CYCLES + | 0 << CS_ACTIVE_BSY + | 17 << BAD_BLOCK_BYTE_NUM + | 1 << BAD_BLOCK_IN_SPARE_AREA + | 2 << WR_RD_BSY_GAP + | wide_bus << WIDE_FLASH + | 1 << DEV0_CFG1_ECC_DISABLE; + + host->ecc_bch_cfg = host->bch_enabled << ECC_CFG_ECC_DISABLE + | 0 << ECC_SW_RESET + | host->cw_data << ECC_NUM_DATA_BYTES + | 1 << ECC_FORCE_CLK_OPEN + | ecc_mode << ECC_MODE + | host->ecc_bytes_hw << ECC_PARITY_SIZE_BYTES_BCH; + + host->ecc_buf_cfg = 0x203 << NUM_STEPS; + + host->clrflashstatus = FS_READY_BSY_N; + host->clrreadstatus = 0xc0; + + dev_dbg(nandc->dev, + "cfg0 %x cfg1 %x ecc_buf_cfg %x ecc_bch cfg %x cw_size %d cw_data %d strength %d parity_bytes %d steps %d\n", + host->cfg0, host->cfg1, host->ecc_buf_cfg, host->ecc_bch_cfg, + host->cw_size, host->cw_data, ecc->strength, ecc->bytes, + cwperpage); + + return 0; +} + +static int qcom_nandc_alloc(struct qcom_nand_controller *nandc) +{ + int ret; + + ret = dma_set_coherent_mask(nandc->dev, DMA_BIT_MASK(32)); + if (ret) { + dev_err(nandc->dev, "failed to set DMA mask\n"); + return ret; + } + + /* + * we use the internal buffer for reading ONFI params, reading small + * data like ID and status, and preforming read-copy-write operations + * when writing to a codeword partially. 532 is the maximum possible + * size of a codeword for our nand controller + */ + nandc->buf_size = 532; + + nandc->data_buffer = devm_kzalloc(nandc->dev, nandc->buf_size, + GFP_KERNEL); + if (!nandc->data_buffer) + return -ENOMEM; + + nandc->regs = devm_kzalloc(nandc->dev, sizeof(*nandc->regs), + GFP_KERNEL); + if (!nandc->regs) + return -ENOMEM; + + nandc->reg_read_buf = devm_kzalloc(nandc->dev, + MAX_REG_RD * sizeof(*nandc->reg_read_buf), + GFP_KERNEL); + if (!nandc->reg_read_buf) + return -ENOMEM; + + nandc->chan = dma_request_slave_channel(nandc->dev, "rxtx"); + if (!nandc->chan) { + dev_err(nandc->dev, "failed to request slave channel\n"); + return -ENODEV; + } + + INIT_LIST_HEAD(&nandc->desc_list); + INIT_LIST_HEAD(&nandc->host_list); + + spin_lock_init(&nandc->controller.lock); + init_waitqueue_head(&nandc->controller.wq); + + return 0; +} + +static void qcom_nandc_unalloc(struct qcom_nand_controller *nandc) +{ + dma_release_channel(nandc->chan); +} + +/* one time setup of a few nand controller registers */ +static int qcom_nandc_setup(struct qcom_nand_controller *nandc) +{ + /* kill onenand */ + nandc_write(nandc, SFLASHC_BURST_CFG, 0); + + /* enable ADM DMA */ + nandc_write(nandc, NAND_FLASH_CHIP_SELECT, DM_EN); + + /* save the original values of these registers */ + nandc->cmd1 = nandc_read(nandc, NAND_DEV_CMD1); + nandc->vld = nandc_read(nandc, NAND_DEV_CMD_VLD); + + return 0; +} + +static int qcom_nand_host_init(struct qcom_nand_controller *nandc, + struct qcom_nand_host *host, + struct device_node *dn) +{ + struct nand_chip *chip = &host->chip; + struct mtd_info *mtd = nand_to_mtd(chip); + struct device *dev = nandc->dev; + int ret; + + ret = of_property_read_u32(dn, "reg", &host->cs); + if (ret) { + dev_err(dev, "can't get chip-select\n"); + return -ENXIO; + } + + nand_set_flash_node(chip, dn); + mtd->name = devm_kasprintf(dev, GFP_KERNEL, "qcom_nand.%d", host->cs); + mtd->owner = THIS_MODULE; + mtd->dev.parent = dev; + + chip->cmdfunc = qcom_nandc_command; + chip->select_chip = qcom_nandc_select_chip; + chip->read_byte = qcom_nandc_read_byte; + chip->read_buf = qcom_nandc_read_buf; + chip->write_buf = qcom_nandc_write_buf; + + /* + * the bad block marker is readable only when we read the last codeword + * of a page with ECC disabled. currently, the nand_base and nand_bbt + * helpers don't allow us to read BB from a nand chip with ECC + * disabled (MTD_OPS_PLACE_OOB is set by default). use the block_bad + * and block_markbad helpers until we permanently switch to using + * MTD_OPS_RAW for all drivers (with the help of badblockbits) + */ + chip->block_bad = qcom_nandc_block_bad; + chip->block_markbad = qcom_nandc_block_markbad; + + chip->controller = &nandc->controller; + chip->options |= NAND_NO_SUBPAGE_WRITE | NAND_USE_BOUNCE_BUFFER | + NAND_SKIP_BBTSCAN; + + /* set up initial status value */ + host->status = NAND_STATUS_READY | NAND_STATUS_WP; + + ret = nand_scan_ident(mtd, 1, NULL); + if (ret) + return ret; + + ret = qcom_nand_host_setup(host); + if (ret) + return ret; + + ret = nand_scan_tail(mtd); + if (ret) + return ret; + + return mtd_device_register(mtd, NULL, 0); +} + +/* parse custom DT properties here */ +static int qcom_nandc_parse_dt(struct platform_device *pdev) +{ + struct qcom_nand_controller *nandc = platform_get_drvdata(pdev); + struct device_node *np = nandc->dev->of_node; + int ret; + + ret = of_property_read_u32(np, "qcom,cmd-crci", &nandc->cmd_crci); + if (ret) { + dev_err(nandc->dev, "command CRCI unspecified\n"); + return ret; + } + + ret = of_property_read_u32(np, "qcom,data-crci", &nandc->data_crci); + if (ret) { + dev_err(nandc->dev, "data CRCI unspecified\n"); + return ret; + } + + return 0; +} + +static int qcom_nandc_probe(struct platform_device *pdev) +{ + struct qcom_nand_controller *nandc; + struct qcom_nand_host *host; + const void *dev_data; + struct device *dev = &pdev->dev; + struct device_node *dn = dev->of_node, *child; + struct resource *res; + int ret; + + nandc = devm_kzalloc(&pdev->dev, sizeof(*nandc), GFP_KERNEL); + if (!nandc) + return -ENOMEM; + + platform_set_drvdata(pdev, nandc); + nandc->dev = dev; + + dev_data = of_device_get_match_data(dev); + if (!dev_data) { + dev_err(&pdev->dev, "failed to get device data\n"); + return -ENODEV; + } + + nandc->ecc_modes = (unsigned long)dev_data; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + nandc->base = devm_ioremap_resource(dev, res); + if (IS_ERR(nandc->base)) + return PTR_ERR(nandc->base); + + nandc->base_dma = phys_to_dma(dev, (phys_addr_t)res->start); + + nandc->core_clk = devm_clk_get(dev, "core"); + if (IS_ERR(nandc->core_clk)) + return PTR_ERR(nandc->core_clk); + + nandc->aon_clk = devm_clk_get(dev, "aon"); + if (IS_ERR(nandc->aon_clk)) + return PTR_ERR(nandc->aon_clk); + + ret = qcom_nandc_parse_dt(pdev); + if (ret) + return ret; + + ret = qcom_nandc_alloc(nandc); + if (ret) + return ret; + + ret = clk_prepare_enable(nandc->core_clk); + if (ret) + goto err_core_clk; + + ret = clk_prepare_enable(nandc->aon_clk); + if (ret) + goto err_aon_clk; + + ret = qcom_nandc_setup(nandc); + if (ret) + goto err_setup; + + for_each_available_child_of_node(dn, child) { + if (of_device_is_compatible(child, "qcom,nandcs")) { + host = devm_kzalloc(dev, sizeof(*host), GFP_KERNEL); + if (!host) { + of_node_put(child); + ret = -ENOMEM; + goto err_cs_init; + } + + ret = qcom_nand_host_init(nandc, host, child); + if (ret) { + devm_kfree(dev, host); + continue; + } + + list_add_tail(&host->node, &nandc->host_list); + } + } + + if (list_empty(&nandc->host_list)) { + ret = -ENODEV; + goto err_cs_init; + } + + return 0; + +err_cs_init: + list_for_each_entry(host, &nandc->host_list, node) + nand_release(nand_to_mtd(&host->chip)); +err_setup: + clk_disable_unprepare(nandc->aon_clk); +err_aon_clk: + clk_disable_unprepare(nandc->core_clk); +err_core_clk: + qcom_nandc_unalloc(nandc); + + return ret; +} + +static int qcom_nandc_remove(struct platform_device *pdev) +{ + struct qcom_nand_controller *nandc = platform_get_drvdata(pdev); + struct qcom_nand_host *host; + + list_for_each_entry(host, &nandc->host_list, node) + nand_release(nand_to_mtd(&host->chip)); + + qcom_nandc_unalloc(nandc); + + clk_disable_unprepare(nandc->aon_clk); + clk_disable_unprepare(nandc->core_clk); + + return 0; +} + +#define EBI2_NANDC_ECC_MODES (ECC_RS_4BIT | ECC_BCH_8BIT) + +/* + * data will hold a struct pointer containing more differences once we support + * more controller variants + */ +static const struct of_device_id qcom_nandc_of_match[] = { + { .compatible = "qcom,ipq806x-nand", + .data = (void *)EBI2_NANDC_ECC_MODES, + }, + {} +}; +MODULE_DEVICE_TABLE(of, qcom_nandc_of_match); + +static struct platform_driver qcom_nandc_driver = { + .driver = { + .name = "qcom-nandc", + .of_match_table = qcom_nandc_of_match, + }, + .probe = qcom_nandc_probe, + .remove = qcom_nandc_remove, +}; +module_platform_driver(qcom_nandc_driver); + +MODULE_AUTHOR("Archit Taneja <architt@codeaurora.org>"); +MODULE_DESCRIPTION("Qualcomm NAND Controller driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/mtd/nand/s3c2410.c b/drivers/mtd/nand/s3c2410.c index 01ac74fa3b95..9c9397b54b2c 100644 --- a/drivers/mtd/nand/s3c2410.c +++ b/drivers/mtd/nand/s3c2410.c @@ -861,9 +861,6 @@ static void s3c2410_nand_init_chip(struct s3c2410_nand_info *info, chip->ecc.mode = NAND_ECC_SOFT; #endif - if (set->ecc_layout != NULL) - chip->ecc.layout = set->ecc_layout; - if (set->disable_ecc) chip->ecc.mode = NAND_ECC_NONE; diff --git a/drivers/mtd/nand/sunxi_nand.c b/drivers/mtd/nand/sunxi_nand.c index 51e10a35fe08..1c03eee44f3d 100644 --- a/drivers/mtd/nand/sunxi_nand.c +++ b/drivers/mtd/nand/sunxi_nand.c @@ -60,6 +60,7 @@ #define NFC_REG_ECC_ERR_CNT(x) ((0x0040 + (x)) & ~0x3) #define NFC_REG_USER_DATA(x) (0x0050 + ((x) * 4)) #define NFC_REG_SPARE_AREA 0x00A0 +#define NFC_REG_PAT_ID 0x00A4 #define NFC_RAM0_BASE 0x0400 #define NFC_RAM1_BASE 0x0800 @@ -538,6 +539,174 @@ static void sunxi_nfc_cmd_ctrl(struct mtd_info *mtd, int dat, sunxi_nfc_wait_int(nfc, NFC_CMD_INT_FLAG, 0); } +/* These seed values have been extracted from Allwinner's BSP */ +static const u16 sunxi_nfc_randomizer_page_seeds[] = { + 0x2b75, 0x0bd0, 0x5ca3, 0x62d1, 0x1c93, 0x07e9, 0x2162, 0x3a72, + 0x0d67, 0x67f9, 0x1be7, 0x077d, 0x032f, 0x0dac, 0x2716, 0x2436, + 0x7922, 0x1510, 0x3860, 0x5287, 0x480f, 0x4252, 0x1789, 0x5a2d, + 0x2a49, 0x5e10, 0x437f, 0x4b4e, 0x2f45, 0x216e, 0x5cb7, 0x7130, + 0x2a3f, 0x60e4, 0x4dc9, 0x0ef0, 0x0f52, 0x1bb9, 0x6211, 0x7a56, + 0x226d, 0x4ea7, 0x6f36, 0x3692, 0x38bf, 0x0c62, 0x05eb, 0x4c55, + 0x60f4, 0x728c, 0x3b6f, 0x2037, 0x7f69, 0x0936, 0x651a, 0x4ceb, + 0x6218, 0x79f3, 0x383f, 0x18d9, 0x4f05, 0x5c82, 0x2912, 0x6f17, + 0x6856, 0x5938, 0x1007, 0x61ab, 0x3e7f, 0x57c2, 0x542f, 0x4f62, + 0x7454, 0x2eac, 0x7739, 0x42d4, 0x2f90, 0x435a, 0x2e52, 0x2064, + 0x637c, 0x66ad, 0x2c90, 0x0bad, 0x759c, 0x0029, 0x0986, 0x7126, + 0x1ca7, 0x1605, 0x386a, 0x27f5, 0x1380, 0x6d75, 0x24c3, 0x0f8e, + 0x2b7a, 0x1418, 0x1fd1, 0x7dc1, 0x2d8e, 0x43af, 0x2267, 0x7da3, + 0x4e3d, 0x1338, 0x50db, 0x454d, 0x764d, 0x40a3, 0x42e6, 0x262b, + 0x2d2e, 0x1aea, 0x2e17, 0x173d, 0x3a6e, 0x71bf, 0x25f9, 0x0a5d, + 0x7c57, 0x0fbe, 0x46ce, 0x4939, 0x6b17, 0x37bb, 0x3e91, 0x76db, +}; + +/* + * sunxi_nfc_randomizer_ecc512_seeds and sunxi_nfc_randomizer_ecc1024_seeds + * have been generated using + * sunxi_nfc_randomizer_step(seed, (step_size * 8) + 15), which is what + * the randomizer engine does internally before de/scrambling OOB data. + * + * Those tables are statically defined to avoid calculating randomizer state + * at runtime. + */ +static const u16 sunxi_nfc_randomizer_ecc512_seeds[] = { + 0x3346, 0x367f, 0x1f18, 0x769a, 0x4f64, 0x068c, 0x2ef1, 0x6b64, + 0x28a9, 0x15d7, 0x30f8, 0x3659, 0x53db, 0x7c5f, 0x71d4, 0x4409, + 0x26eb, 0x03cc, 0x655d, 0x47d4, 0x4daa, 0x0877, 0x712d, 0x3617, + 0x3264, 0x49aa, 0x7f9e, 0x588e, 0x4fbc, 0x7176, 0x7f91, 0x6c6d, + 0x4b95, 0x5fb7, 0x3844, 0x4037, 0x0184, 0x081b, 0x0ee8, 0x5b91, + 0x293d, 0x1f71, 0x0e6f, 0x402b, 0x5122, 0x1e52, 0x22be, 0x3d2d, + 0x75bc, 0x7c60, 0x6291, 0x1a2f, 0x61d4, 0x74aa, 0x4140, 0x29ab, + 0x472d, 0x2852, 0x017e, 0x15e8, 0x5ec2, 0x17cf, 0x7d0f, 0x06b8, + 0x117a, 0x6b94, 0x789b, 0x3126, 0x6ac5, 0x5be7, 0x150f, 0x51f8, + 0x7889, 0x0aa5, 0x663d, 0x77e8, 0x0b87, 0x3dcb, 0x360d, 0x218b, + 0x512f, 0x7dc9, 0x6a4d, 0x630a, 0x3547, 0x1dd2, 0x5aea, 0x69a5, + 0x7bfa, 0x5e4f, 0x1519, 0x6430, 0x3a0e, 0x5eb3, 0x5425, 0x0c7a, + 0x5540, 0x3670, 0x63c1, 0x31e9, 0x5a39, 0x2de7, 0x5979, 0x2891, + 0x1562, 0x014b, 0x5b05, 0x2756, 0x5a34, 0x13aa, 0x6cb5, 0x2c36, + 0x5e72, 0x1306, 0x0861, 0x15ef, 0x1ee8, 0x5a37, 0x7ac4, 0x45dd, + 0x44c4, 0x7266, 0x2f41, 0x3ccc, 0x045e, 0x7d40, 0x7c66, 0x0fa0, +}; + +static const u16 sunxi_nfc_randomizer_ecc1024_seeds[] = { + 0x2cf5, 0x35f1, 0x63a4, 0x5274, 0x2bd2, 0x778b, 0x7285, 0x32b6, + 0x6a5c, 0x70d6, 0x757d, 0x6769, 0x5375, 0x1e81, 0x0cf3, 0x3982, + 0x6787, 0x042a, 0x6c49, 0x1925, 0x56a8, 0x40a9, 0x063e, 0x7bd9, + 0x4dbf, 0x55ec, 0x672e, 0x7334, 0x5185, 0x4d00, 0x232a, 0x7e07, + 0x445d, 0x6b92, 0x528f, 0x4255, 0x53ba, 0x7d82, 0x2a2e, 0x3a4e, + 0x75eb, 0x450c, 0x6844, 0x1b5d, 0x581a, 0x4cc6, 0x0379, 0x37b2, + 0x419f, 0x0e92, 0x6b27, 0x5624, 0x01e3, 0x07c1, 0x44a5, 0x130c, + 0x13e8, 0x5910, 0x0876, 0x60c5, 0x54e3, 0x5b7f, 0x2269, 0x509f, + 0x7665, 0x36fd, 0x3e9a, 0x0579, 0x6295, 0x14ef, 0x0a81, 0x1bcc, + 0x4b16, 0x64db, 0x0514, 0x4f07, 0x0591, 0x3576, 0x6853, 0x0d9e, + 0x259f, 0x38b7, 0x64fb, 0x3094, 0x4693, 0x6ddd, 0x29bb, 0x0bc8, + 0x3f47, 0x490e, 0x0c0e, 0x7933, 0x3c9e, 0x5840, 0x398d, 0x3e68, + 0x4af1, 0x71f5, 0x57cf, 0x1121, 0x64eb, 0x3579, 0x15ac, 0x584d, + 0x5f2a, 0x47e2, 0x6528, 0x6eac, 0x196e, 0x6b96, 0x0450, 0x0179, + 0x609c, 0x06e1, 0x4626, 0x42c7, 0x273e, 0x486f, 0x0705, 0x1601, + 0x145b, 0x407e, 0x062b, 0x57a5, 0x53f9, 0x5659, 0x4410, 0x3ccd, +}; + +static u16 sunxi_nfc_randomizer_step(u16 state, int count) +{ + state &= 0x7fff; + + /* + * This loop is just a simple implementation of a Fibonacci LFSR using + * the x16 + x15 + 1 polynomial. + */ + while (count--) + state = ((state >> 1) | + (((state ^ (state >> 1)) & 1) << 14)) & 0x7fff; + + return state; +} + +static u16 sunxi_nfc_randomizer_state(struct mtd_info *mtd, int page, bool ecc) +{ + const u16 *seeds = sunxi_nfc_randomizer_page_seeds; + int mod = mtd_div_by_ws(mtd->erasesize, mtd); + + if (mod > ARRAY_SIZE(sunxi_nfc_randomizer_page_seeds)) + mod = ARRAY_SIZE(sunxi_nfc_randomizer_page_seeds); + + if (ecc) { + if (mtd->ecc_step_size == 512) + seeds = sunxi_nfc_randomizer_ecc512_seeds; + else + seeds = sunxi_nfc_randomizer_ecc1024_seeds; + } + + return seeds[page % mod]; +} + +static void sunxi_nfc_randomizer_config(struct mtd_info *mtd, + int page, bool ecc) +{ + struct nand_chip *nand = mtd_to_nand(mtd); + struct sunxi_nfc *nfc = to_sunxi_nfc(nand->controller); + u32 ecc_ctl = readl(nfc->regs + NFC_REG_ECC_CTL); + u16 state; + + if (!(nand->options & NAND_NEED_SCRAMBLING)) + return; + + ecc_ctl = readl(nfc->regs + NFC_REG_ECC_CTL); + state = sunxi_nfc_randomizer_state(mtd, page, ecc); + ecc_ctl = readl(nfc->regs + NFC_REG_ECC_CTL) & ~NFC_RANDOM_SEED_MSK; + writel(ecc_ctl | NFC_RANDOM_SEED(state), nfc->regs + NFC_REG_ECC_CTL); +} + +static void sunxi_nfc_randomizer_enable(struct mtd_info *mtd) +{ + struct nand_chip *nand = mtd_to_nand(mtd); + struct sunxi_nfc *nfc = to_sunxi_nfc(nand->controller); + + if (!(nand->options & NAND_NEED_SCRAMBLING)) + return; + + writel(readl(nfc->regs + NFC_REG_ECC_CTL) | NFC_RANDOM_EN, + nfc->regs + NFC_REG_ECC_CTL); +} + +static void sunxi_nfc_randomizer_disable(struct mtd_info *mtd) +{ + struct nand_chip *nand = mtd_to_nand(mtd); + struct sunxi_nfc *nfc = to_sunxi_nfc(nand->controller); + + if (!(nand->options & NAND_NEED_SCRAMBLING)) + return; + + writel(readl(nfc->regs + NFC_REG_ECC_CTL) & ~NFC_RANDOM_EN, + nfc->regs + NFC_REG_ECC_CTL); +} + +static void sunxi_nfc_randomize_bbm(struct mtd_info *mtd, int page, u8 *bbm) +{ + u16 state = sunxi_nfc_randomizer_state(mtd, page, true); + + bbm[0] ^= state; + bbm[1] ^= sunxi_nfc_randomizer_step(state, 8); +} + +static void sunxi_nfc_randomizer_write_buf(struct mtd_info *mtd, + const uint8_t *buf, int len, + bool ecc, int page) +{ + sunxi_nfc_randomizer_config(mtd, page, ecc); + sunxi_nfc_randomizer_enable(mtd); + sunxi_nfc_write_buf(mtd, buf, len); + sunxi_nfc_randomizer_disable(mtd); +} + +static void sunxi_nfc_randomizer_read_buf(struct mtd_info *mtd, uint8_t *buf, + int len, bool ecc, int page) +{ + sunxi_nfc_randomizer_config(mtd, page, ecc); + sunxi_nfc_randomizer_enable(mtd); + sunxi_nfc_read_buf(mtd, buf, len); + sunxi_nfc_randomizer_disable(mtd); +} + static void sunxi_nfc_hw_ecc_enable(struct mtd_info *mtd) { struct nand_chip *nand = mtd_to_nand(mtd); @@ -574,18 +743,20 @@ static int sunxi_nfc_hw_ecc_read_chunk(struct mtd_info *mtd, u8 *data, int data_off, u8 *oob, int oob_off, int *cur_off, - unsigned int *max_bitflips) + unsigned int *max_bitflips, + bool bbm, int page) { struct nand_chip *nand = mtd_to_nand(mtd); struct sunxi_nfc *nfc = to_sunxi_nfc(nand->controller); struct nand_ecc_ctrl *ecc = &nand->ecc; + int raw_mode = 0; u32 status; int ret; if (*cur_off != data_off) nand->cmdfunc(mtd, NAND_CMD_RNDOUT, data_off, -1); - sunxi_nfc_read_buf(mtd, NULL, ecc->size); + sunxi_nfc_randomizer_read_buf(mtd, NULL, ecc->size, false, page); if (data_off + ecc->size != oob_off) nand->cmdfunc(mtd, NAND_CMD_RNDOUT, oob_off, -1); @@ -594,25 +765,54 @@ static int sunxi_nfc_hw_ecc_read_chunk(struct mtd_info *mtd, if (ret) return ret; + sunxi_nfc_randomizer_enable(mtd); writel(NFC_DATA_TRANS | NFC_DATA_SWAP_METHOD | NFC_ECC_OP, nfc->regs + NFC_REG_CMD); ret = sunxi_nfc_wait_int(nfc, NFC_CMD_INT_FLAG, 0); + sunxi_nfc_randomizer_disable(mtd); if (ret) return ret; + *cur_off = oob_off + ecc->bytes + 4; + status = readl(nfc->regs + NFC_REG_ECC_ST); + if (status & NFC_ECC_PAT_FOUND(0)) { + u8 pattern = 0xff; + + if (unlikely(!(readl(nfc->regs + NFC_REG_PAT_ID) & 0x1))) + pattern = 0x0; + + memset(data, pattern, ecc->size); + memset(oob, pattern, ecc->bytes + 4); + + return 1; + } + ret = NFC_ECC_ERR_CNT(0, readl(nfc->regs + NFC_REG_ECC_ERR_CNT(0))); memcpy_fromio(data, nfc->regs + NFC_RAM0_BASE, ecc->size); nand->cmdfunc(mtd, NAND_CMD_RNDOUT, oob_off, -1); - sunxi_nfc_read_buf(mtd, oob, ecc->bytes + 4); + sunxi_nfc_randomizer_read_buf(mtd, oob, ecc->bytes + 4, true, page); if (status & NFC_ECC_ERR(0)) { + /* + * Re-read the data with the randomizer disabled to identify + * bitflips in erased pages. + */ + if (nand->options & NAND_NEED_SCRAMBLING) { + nand->cmdfunc(mtd, NAND_CMD_RNDOUT, data_off, -1); + nand->read_buf(mtd, data, ecc->size); + nand->cmdfunc(mtd, NAND_CMD_RNDOUT, oob_off, -1); + nand->read_buf(mtd, oob, ecc->bytes + 4); + } + ret = nand_check_erased_ecc_chunk(data, ecc->size, oob, ecc->bytes + 4, NULL, 0, ecc->strength); + if (ret >= 0) + raw_mode = 1; } else { /* * The engine protects 4 bytes of OOB data per chunk. @@ -620,6 +820,10 @@ static int sunxi_nfc_hw_ecc_read_chunk(struct mtd_info *mtd, */ sunxi_nfc_user_data_to_buf(readl(nfc->regs + NFC_REG_USER_DATA(0)), oob); + + /* De-randomize the Bad Block Marker. */ + if (bbm && nand->options & NAND_NEED_SCRAMBLING) + sunxi_nfc_randomize_bbm(mtd, page, oob); } if (ret < 0) { @@ -629,13 +833,12 @@ static int sunxi_nfc_hw_ecc_read_chunk(struct mtd_info *mtd, *max_bitflips = max_t(unsigned int, *max_bitflips, ret); } - *cur_off = oob_off + ecc->bytes + 4; - - return 0; + return raw_mode; } static void sunxi_nfc_hw_ecc_read_extra_oob(struct mtd_info *mtd, - u8 *oob, int *cur_off) + u8 *oob, int *cur_off, + bool randomize, int page) { struct nand_chip *nand = mtd_to_nand(mtd); struct nand_ecc_ctrl *ecc = &nand->ecc; @@ -649,7 +852,11 @@ static void sunxi_nfc_hw_ecc_read_extra_oob(struct mtd_info *mtd, nand->cmdfunc(mtd, NAND_CMD_RNDOUT, offset + mtd->writesize, -1); - sunxi_nfc_read_buf(mtd, oob + offset, len); + if (!randomize) + sunxi_nfc_read_buf(mtd, oob + offset, len); + else + sunxi_nfc_randomizer_read_buf(mtd, oob + offset, len, + false, page); *cur_off = mtd->oobsize + mtd->writesize; } @@ -662,7 +869,8 @@ static inline u32 sunxi_nfc_buf_to_user_data(const u8 *buf) static int sunxi_nfc_hw_ecc_write_chunk(struct mtd_info *mtd, const u8 *data, int data_off, const u8 *oob, int oob_off, - int *cur_off) + int *cur_off, bool bbm, + int page) { struct nand_chip *nand = mtd_to_nand(mtd); struct sunxi_nfc *nfc = to_sunxi_nfc(nand->controller); @@ -672,11 +880,20 @@ static int sunxi_nfc_hw_ecc_write_chunk(struct mtd_info *mtd, if (data_off != *cur_off) nand->cmdfunc(mtd, NAND_CMD_RNDIN, data_off, -1); - sunxi_nfc_write_buf(mtd, data, ecc->size); + sunxi_nfc_randomizer_write_buf(mtd, data, ecc->size, false, page); /* Fill OOB data in */ - writel(sunxi_nfc_buf_to_user_data(oob), - nfc->regs + NFC_REG_USER_DATA(0)); + if ((nand->options & NAND_NEED_SCRAMBLING) && bbm) { + u8 user_data[4]; + + memcpy(user_data, oob, 4); + sunxi_nfc_randomize_bbm(mtd, page, user_data); + writel(sunxi_nfc_buf_to_user_data(user_data), + nfc->regs + NFC_REG_USER_DATA(0)); + } else { + writel(sunxi_nfc_buf_to_user_data(oob), + nfc->regs + NFC_REG_USER_DATA(0)); + } if (data_off + ecc->size != oob_off) nand->cmdfunc(mtd, NAND_CMD_RNDIN, oob_off, -1); @@ -685,11 +902,13 @@ static int sunxi_nfc_hw_ecc_write_chunk(struct mtd_info *mtd, if (ret) return ret; + sunxi_nfc_randomizer_enable(mtd); writel(NFC_DATA_TRANS | NFC_DATA_SWAP_METHOD | NFC_ACCESS_DIR | NFC_ECC_OP, nfc->regs + NFC_REG_CMD); ret = sunxi_nfc_wait_int(nfc, NFC_CMD_INT_FLAG, 0); + sunxi_nfc_randomizer_disable(mtd); if (ret) return ret; @@ -699,7 +918,8 @@ static int sunxi_nfc_hw_ecc_write_chunk(struct mtd_info *mtd, } static void sunxi_nfc_hw_ecc_write_extra_oob(struct mtd_info *mtd, - u8 *oob, int *cur_off) + u8 *oob, int *cur_off, + int page) { struct nand_chip *nand = mtd_to_nand(mtd); struct nand_ecc_ctrl *ecc = &nand->ecc; @@ -713,7 +933,7 @@ static void sunxi_nfc_hw_ecc_write_extra_oob(struct mtd_info *mtd, nand->cmdfunc(mtd, NAND_CMD_RNDIN, offset + mtd->writesize, -1); - sunxi_nfc_write_buf(mtd, oob + offset, len); + sunxi_nfc_randomizer_write_buf(mtd, oob + offset, len, false, page); *cur_off = mtd->oobsize + mtd->writesize; } @@ -725,6 +945,7 @@ static int sunxi_nfc_hw_ecc_read_page(struct mtd_info *mtd, struct nand_ecc_ctrl *ecc = &chip->ecc; unsigned int max_bitflips = 0; int ret, i, cur_off = 0; + bool raw_mode = false; sunxi_nfc_hw_ecc_enable(mtd); @@ -736,13 +957,17 @@ static int sunxi_nfc_hw_ecc_read_page(struct mtd_info *mtd, ret = sunxi_nfc_hw_ecc_read_chunk(mtd, data, data_off, oob, oob_off + mtd->writesize, - &cur_off, &max_bitflips); - if (ret) + &cur_off, &max_bitflips, + !i, page); + if (ret < 0) return ret; + else if (ret) + raw_mode = true; } if (oob_required) - sunxi_nfc_hw_ecc_read_extra_oob(mtd, chip->oob_poi, &cur_off); + sunxi_nfc_hw_ecc_read_extra_oob(mtd, chip->oob_poi, &cur_off, + !raw_mode, page); sunxi_nfc_hw_ecc_disable(mtd); @@ -767,13 +992,14 @@ static int sunxi_nfc_hw_ecc_write_page(struct mtd_info *mtd, ret = sunxi_nfc_hw_ecc_write_chunk(mtd, data, data_off, oob, oob_off + mtd->writesize, - &cur_off); + &cur_off, !i, page); if (ret) return ret; } - if (oob_required) - sunxi_nfc_hw_ecc_write_extra_oob(mtd, chip->oob_poi, &cur_off); + if (oob_required || (chip->options & NAND_NEED_SCRAMBLING)) + sunxi_nfc_hw_ecc_write_extra_oob(mtd, chip->oob_poi, + &cur_off, page); sunxi_nfc_hw_ecc_disable(mtd); @@ -788,6 +1014,7 @@ static int sunxi_nfc_hw_syndrome_ecc_read_page(struct mtd_info *mtd, struct nand_ecc_ctrl *ecc = &chip->ecc; unsigned int max_bitflips = 0; int ret, i, cur_off = 0; + bool raw_mode = false; sunxi_nfc_hw_ecc_enable(mtd); @@ -799,13 +1026,16 @@ static int sunxi_nfc_hw_syndrome_ecc_read_page(struct mtd_info *mtd, ret = sunxi_nfc_hw_ecc_read_chunk(mtd, data, data_off, oob, oob_off, &cur_off, - &max_bitflips); - if (ret) + &max_bitflips, !i, page); + if (ret < 0) return ret; + else if (ret) + raw_mode = true; } if (oob_required) - sunxi_nfc_hw_ecc_read_extra_oob(mtd, chip->oob_poi, &cur_off); + sunxi_nfc_hw_ecc_read_extra_oob(mtd, chip->oob_poi, &cur_off, + !raw_mode, page); sunxi_nfc_hw_ecc_disable(mtd); @@ -829,13 +1059,15 @@ static int sunxi_nfc_hw_syndrome_ecc_write_page(struct mtd_info *mtd, const u8 *oob = chip->oob_poi + (i * (ecc->bytes + 4)); ret = sunxi_nfc_hw_ecc_write_chunk(mtd, data, data_off, - oob, oob_off, &cur_off); + oob, oob_off, &cur_off, + false, page); if (ret) return ret; } - if (oob_required) - sunxi_nfc_hw_ecc_write_extra_oob(mtd, chip->oob_poi, &cur_off); + if (oob_required || (chip->options & NAND_NEED_SCRAMBLING)) + sunxi_nfc_hw_ecc_write_extra_oob(mtd, chip->oob_poi, + &cur_off, page); sunxi_nfc_hw_ecc_disable(mtd); @@ -1345,6 +1577,9 @@ static int sunxi_nand_chip_init(struct device *dev, struct sunxi_nfc *nfc, if (nand->bbt_options & NAND_BBT_USE_FLASH) nand->bbt_options |= NAND_BBT_NO_OOB; + if (nand->options & NAND_NEED_SCRAMBLING) + nand->options |= NAND_NO_SUBPAGE_WRITE; + ret = sunxi_nand_chip_init_timings(chip, np); if (ret) { dev_err(dev, "could not configure chip timings: %d\n", ret); diff --git a/drivers/mtd/nand/vf610_nfc.c b/drivers/mtd/nand/vf610_nfc.c index 034420f313d5..293feb19b0b1 100644 --- a/drivers/mtd/nand/vf610_nfc.c +++ b/drivers/mtd/nand/vf610_nfc.c @@ -795,8 +795,6 @@ static int vf610_nfc_probe(struct platform_device *pdev) goto error; } - /* propagate ecc.layout to mtd_info */ - mtd->ecclayout = chip->ecc.layout; chip->ecc.read_page = vf610_nfc_read_page; chip->ecc.write_page = vf610_nfc_write_page; |