1 files changed, 0 insertions, 119 deletions
diff --git a/arch/cris/arch-v32/mach-a3/dram_init.S b/arch/cris/arch-v32/mach-a3/dram_init.S
deleted file mode 100644
index 733c3564ad79..000000000000
--- a/arch/cris/arch-v32/mach-a3/dram_init.S
+++ /dev/null
@@ -1,119 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * DDR SDRAM initialization - alter with care
- * This file is intended to be included from other assembler files
- *
- * Note: This file may not modify r8 or r9 because they are used to
- * carry information from the decompressor to the kernel
- *
- * Copyright (C) 2005-2007 Axis Communications AB
- *
- * Authors:  Mikael Starvik <starvik@axis.com>
- */
-
-/* Just to be certain the config file is included, we include it here
- * explicitly instead of depending on it being included in the file that
- * uses this code.
- */
-
-#include <hwregs/asm/reg_map_asm.h>
-#include <hwregs/asm/ddr2_defs_asm.h>
-
-	;; WARNING! The registers r8 and r9 are used as parameters carrying
-	;; information from the decompressor (if the kernel was compressed).
-	;; They should not be used in the code below.
-
-	;; Refer to ddr2 MDS for initialization sequence
-
-	; 2. Wait 200us
-	move.d   10000, $r2
-1:	bne      1b
-	subq     1, $r2
-
-	; Start clock
-	move.d   REG_ADDR(ddr2, regi_ddr2_ctrl, rw_phy_cfg), $r0
-	move.d   REG_STATE(ddr2, rw_phy_cfg, en, yes), $r1
-	move.d   $r1, [$r0]
-
-	; 2. Wait 200us
-	move.d   10000, $r2
-1:	bne      1b
-	subq     1, $r2
-
-	; Reset phy and start calibration
-	move.d   REG_ADDR(ddr2, regi_ddr2_ctrl, rw_phy_ctrl), $r0
-	move.d   REG_STATE(ddr2, rw_phy_ctrl, rst, yes) | \
-		 REG_STATE(ddr2, rw_phy_ctrl, cal_rst, yes), $r1
-	move.d   $r1, [$r0]
-	move.d	 REG_STATE(ddr2, rw_phy_ctrl, cal_start, yes), $r1
-	move.d   $r1, [$r0]
-
-	; 2. Wait 200us
-	move.d   10000, $r2
-1:	bne      1b
-	subq     1, $r2
-
-	; Issue commands
-	move.d   REG_ADDR(ddr2, regi_ddr2_ctrl, rw_ctrl), $r0
-	move.d   sdram_commands_start, $r2
-command_loop:
-	movu.b  [$r2+], $r1
-	movu.w  [$r2+], $r3
-do_cmd:
-	lslq     16, $r1
-	or.d     $r3, $r1
-	move.d   $r1, [$r0]
-	; 2. Wait 200us
-	move.d   10000, $r4
-1:	bne      1b
-	subq     1, $r4
-	cmp.d    sdram_commands_end, $r2
-	blo      command_loop
-	nop
-
-	; Set timing
-	move.d   REG_ADDR(ddr2, regi_ddr2_ctrl, rw_timing), $r0
-	move.d   CONFIG_ETRAX_DDR2_TIMING, $r1
-	move.d   $r1, [$r0]
-
-	; Set latency
-	move.d   REG_ADDR(ddr2, regi_ddr2_ctrl, rw_latency), $r0
-	move.d   CONFIG_ETRAX_DDR2_LATENCY, $r1
-	move.d   $r1, [$r0]
-
-	; Set configuration
-	move.d   REG_ADDR(ddr2, regi_ddr2_ctrl, rw_cfg), $r0
-	move.d   CONFIG_ETRAX_DDR2_CONFIG, $r1
-	move.d   $r1, [$r0]
-
-	ba after_sdram_commands
-	nop
-
-sdram_commands_start:
-	.byte regk_ddr2_deselect
-	.word 0
-	.byte regk_ddr2_pre
-	.word regk_ddr2_pre_all
-	.byte regk_ddr2_emrs2
-	.word 0
-	.byte regk_ddr2_emrs3
-	.word 0
-	.byte regk_ddr2_emrs
-	.word regk_ddr2_dll_en
-	.byte regk_ddr2_mrs
-	.word regk_ddr2_dll_rst
-	.byte regk_ddr2_pre
-	.word regk_ddr2_pre_all
-	.byte regk_ddr2_ref
-	.word 0
-	.byte regk_ddr2_ref
-	.word 0
-	.byte regk_ddr2_mrs
-	.word CONFIG_ETRAX_DDR2_MRS & 0xffff
-	.byte regk_ddr2_emrs
-	.word regk_ddr2_ocd_default | regk_ddr2_dll_en
-	.byte regk_ddr2_emrs
-	.word regk_ddr2_ocd_exit | regk_ddr2_dll_en | (CONFIG_ETRAX_DDR2_MRS >> 16)
-sdram_commands_end:
-	.align 1
-after_sdram_commands: