diff options
Diffstat (limited to 'arch/arm/mach-pxa/palmtreo.c')
| -rw-r--r-- | arch/arm/mach-pxa/palmtreo.c | 105 |
1 files changed, 93 insertions, 12 deletions
diff --git a/arch/arm/mach-pxa/palmtreo.c b/arch/arm/mach-pxa/palmtreo.c index 3f3c48f2f7ce..d82a50b4a803 100644 --- a/arch/arm/mach-pxa/palmtreo.c +++ b/arch/arm/mach-pxa/palmtreo.c @@ -98,9 +98,6 @@ static unsigned long treo_pin_config[] __initdata = { GPIO96_KP_MKOUT_6, GPIO93_KP_DKIN_0 | WAKEUP_ON_LEVEL_HIGH, /* Hotsync button */ - /* LCD */ - GPIOxx_LCD_TFT_16BPP, - /* Quick Capture Interface */ GPIO84_CIF_FV, GPIO85_CIF_LV, @@ -140,6 +137,12 @@ static unsigned long treo680_pin_config[] __initdata = { /* MATRIX KEYPAD - different wake up source */ GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH, GPIO99_KP_MKIN_5, + + /* LCD... L_BIAS alt fn not configured on Treo680; is GPIO instead */ + GPIOxx_LCD_16BPP, + GPIO74_LCD_FCLK, + GPIO75_LCD_LCLK, + GPIO76_LCD_PCLK, }; #endif /* CONFIG_MACH_TREO680 */ @@ -155,13 +158,16 @@ static unsigned long centro685_pin_config[] __initdata = { /* MATRIX KEYPAD - different wake up source */ GPIO100_KP_MKIN_0, GPIO99_KP_MKIN_5 | WAKEUP_ON_LEVEL_HIGH, + + /* LCD */ + GPIOxx_LCD_TFT_16BPP, }; #endif /* CONFIG_MACH_CENTRO */ /****************************************************************************** * GPIO keyboard ******************************************************************************/ -#if defined(CONFIG_KEYBOARD_PXA27x) || defined(CONFIG_KEYBOARD_PXA27x_MODULE) +#if IS_ENABLED(CONFIG_KEYBOARD_PXA27x) static unsigned int treo680_matrix_keys[] = { KEY(0, 0, KEY_F8), /* Red/Off/Power */ KEY(0, 1, KEY_LEFT), @@ -309,7 +315,7 @@ static inline void palmtreo_kpc_init(void) {} /****************************************************************************** * USB host ******************************************************************************/ -#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) +#if IS_ENABLED(CONFIG_USB_OHCI_HCD) static struct pxaohci_platform_data treo680_ohci_info = { .port_mode = PMM_PERPORT_MODE, .flags = ENABLE_PORT1 | ENABLE_PORT3, @@ -328,7 +334,6 @@ static inline void palmtreo_uhc_init(void) {} /****************************************************************************** * Vibra and LEDs ******************************************************************************/ -#ifdef CONFIG_MACH_TREO680 static struct gpio_led treo680_gpio_leds[] = { { .name = "treo680:vibra:vibra", @@ -379,20 +384,46 @@ static struct gpio_led_platform_data centro_gpio_led_info = { static struct platform_device palmtreo_leds = { .name = "leds-gpio", .id = -1, - .dev = { - .platform_data = &treo680_gpio_led_info, - } }; static void __init palmtreo_leds_init(void) { if (machine_is_centro()) palmtreo_leds.dev.platform_data = ¢ro_gpio_led_info; + else if (machine_is_treo680()) + palmtreo_leds.dev.platform_data = &treo680_gpio_led_info; platform_device_register(&palmtreo_leds); } + +/****************************************************************************** + * diskonchip docg4 flash + ******************************************************************************/ +#if defined(CONFIG_MACH_TREO680) +/* REVISIT: does the centro have this device also? */ +#if IS_ENABLED(CONFIG_MTD_NAND_DOCG4) +static struct resource docg4_resources[] = { + { + .start = 0x00000000, + .end = 0x00001FFF, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device treo680_docg4_flash = { + .name = "docg4", + .id = -1, + .resource = docg4_resources, + .num_resources = ARRAY_SIZE(docg4_resources), +}; + +static void __init treo680_docg4_flash_init(void) +{ + platform_device_register(&treo680_docg4_flash); +} #else -static inline void palmtreo_leds_init(void) {} +static inline void treo680_docg4_flash_init(void) {} +#endif #endif /****************************************************************************** @@ -424,12 +455,62 @@ static void __init palmphone_common_init(void) } #ifdef CONFIG_MACH_TREO680 +void __init treo680_gpio_init(void) +{ + unsigned int gpio; + + /* drive all three lcd gpios high initially */ + const unsigned long lcd_flags = GPIOF_INIT_HIGH | GPIOF_DIR_OUT; + + /* + * LCD GPIO initialization... + */ + + /* + * This is likely the power to the lcd. Toggling it low/high appears to + * turn the lcd off/on. Can be toggled after lcd is initialized without + * any apparent adverse effects to the lcd operation. Note that this + * gpio line is used by the lcd controller as the L_BIAS signal, but + * treo680 configures it as gpio. + */ + gpio = GPIO_NR_TREO680_LCD_POWER; + if (gpio_request_one(gpio, lcd_flags, "LCD power") < 0) + goto fail; + + /* + * These two are called "enables", for lack of a better understanding. + * If either of these are toggled after the lcd is initialized, the + * image becomes degraded. N.B. The IPL shipped with the treo + * configures GPIO_NR_TREO680_LCD_EN_N as output and drives it high. If + * the IPL is ever reprogrammed, this initialization may be need to be + * revisited. + */ + gpio = GPIO_NR_TREO680_LCD_EN; + if (gpio_request_one(gpio, lcd_flags, "LCD enable") < 0) + goto fail; + gpio = GPIO_NR_TREO680_LCD_EN_N; + if (gpio_request_one(gpio, lcd_flags, "LCD enable_n") < 0) + goto fail; + + /* driving this low turns LCD on */ + gpio_set_value(GPIO_NR_TREO680_LCD_EN_N, 0); + + return; + fail: + pr_err("gpio %d initialization failed\n", gpio); + gpio_free(GPIO_NR_TREO680_LCD_POWER); + gpio_free(GPIO_NR_TREO680_LCD_EN); + gpio_free(GPIO_NR_TREO680_LCD_EN_N); +} + static void __init treo680_init(void) { pxa2xx_mfp_config(ARRAY_AND_SIZE(treo680_pin_config)); palmphone_common_init(); + treo680_gpio_init(); palm27x_mmc_init(GPIO_NR_TREO_SD_DETECT_N, GPIO_NR_TREO680_SD_READONLY, GPIO_NR_TREO680_SD_POWER, 0); + treo680_docg4_flash_init(); } #endif @@ -451,7 +532,7 @@ MACHINE_START(TREO680, "Palm Treo 680") .nr_irqs = PXA_NR_IRQS, .init_irq = pxa27x_init_irq, .handle_irq = pxa27x_handle_irq, - .timer = &pxa_timer, + .init_time = pxa_timer_init, .init_machine = treo680_init, .restart = pxa_restart, MACHINE_END @@ -465,7 +546,7 @@ MACHINE_START(CENTRO, "Palm Centro 685") .nr_irqs = PXA_NR_IRQS, .init_irq = pxa27x_init_irq, .handle_irq = pxa27x_handle_irq, - .timer = &pxa_timer, + .init_time = pxa_timer_init, .init_machine = centro_init, .restart = pxa_restart, MACHINE_END |