diff options
Diffstat (limited to 'Documentation/devicetree')
13 files changed, 431 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt index 9b8f578d5e19..34a69ba67f13 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt @@ -6,6 +6,7 @@ The MediaTek AUDSYS controller provides various clocks to the system. Required Properties: - compatible: Should be one of: + - "mediatek,mt2701-audsys", "syscon" - "mediatek,mt7622-audsys", "syscon" - #clock-cells: Must be 1 @@ -13,10 +14,19 @@ The AUDSYS controller uses the common clk binding from Documentation/devicetree/bindings/clock/clock-bindings.txt The available clocks are defined in dt-bindings/clock/mt*-clk.h. +Required sub-nodes: +------- +For common binding part and usage, refer to +../sonud/mt2701-afe-pcm.txt. + Example: -audsys: audsys@11220000 { - compatible = "mediatek,mt7622-audsys", "syscon"; - reg = <0 0x11220000 0 0x1000>; - #clock-cells = <1>; -}; + audsys: clock-controller@11220000 { + compatible = "mediatek,mt7622-audsys", "syscon"; + reg = <0 0x11220000 0 0x2000>; + #clock-cells = <1>; + + afe: audio-controller { + ... + }; + }; diff --git a/Documentation/devicetree/bindings/clock/imx6sll-clock.txt b/Documentation/devicetree/bindings/clock/imx6sll-clock.txt new file mode 100644 index 000000000000..fee849d5fdd1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx6sll-clock.txt @@ -0,0 +1,36 @@ +* Clock bindings for Freescale i.MX6 SLL + +Required properties: +- compatible: Should be "fsl,imx6sll-ccm" +- reg: Address and length of the register set +- #clock-cells: Should be <1> +- clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names +- clock-names: should include entries "ckil", "osc", "ipp_di0" and "ipp_di1" + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx6sll-clock.h +for the full list of i.MX6 SLL clock IDs. + +Examples: + +#include <dt-bindings/clock/imx6sll-clock.h> + +clks: clock-controller@20c4000 { + compatible = "fsl,imx6sll-ccm"; + reg = <0x020c4000 0x4000>; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; + #clock-cells = <1>; + clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>; + clock-names = "ckil", "osc", "ipp_di0", "ipp_di1"; +}; + +uart1: serial@2020000 { + compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", "fsl,imx21-uart"; + reg = <0x02020000 0x4000>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6SLL_CLK_UART1_IPG>, + <&clks IMX6SLL_CLK_UART1_SERIAL>; + clock-names = "ipg", "per"; +}; diff --git a/Documentation/devicetree/bindings/clock/intc_stratix10.txt b/Documentation/devicetree/bindings/clock/intc_stratix10.txt new file mode 100644 index 000000000000..9f4ec5cb5c6b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/intc_stratix10.txt @@ -0,0 +1,20 @@ +Device Tree Clock bindings for Intel's SoCFPGA Stratix10 platform + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be + "intel,stratix10-clkmgr" + +- reg : shall be the control register offset from CLOCK_MANAGER's base for the clock. + +- #clock-cells : from common clock binding, shall be set to 1. + +Example: + clkmgr: clock-controller@ffd10000 { + compatible = "intel,stratix10-clkmgr"; + reg = <0xffd10000 0x1000>; + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt index f1890d0777a6..773a5226342f 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt @@ -22,7 +22,9 @@ Required Properties: - "renesas,r8a7794-cpg-mssr" for the r8a7794 SoC (R-Car E2) - "renesas,r8a7795-cpg-mssr" for the r8a7795 SoC (R-Car H3) - "renesas,r8a7796-cpg-mssr" for the r8a7796 SoC (R-Car M3-W) + - "renesas,r8a77965-cpg-mssr" for the r8a77965 SoC (R-Car M3-N) - "renesas,r8a77970-cpg-mssr" for the r8a77970 SoC (R-Car V3M) + - "renesas,r8a77980-cpg-mssr" for the r8a77980 SoC (R-Car V3H) - "renesas,r8a77995-cpg-mssr" for the r8a77995 SoC (R-Car D3) - reg: Base address and length of the memory resource used by the CPG/MSSR @@ -32,8 +34,8 @@ Required Properties: clock-names - clock-names: List of external parent clock names. Valid names are: - "extal" (r8a7743, r8a7745, r8a7790, r8a7791, r8a7792, r8a7793, r8a7794, - r8a7795, r8a7796, r8a77970, r8a77995) - - "extalr" (r8a7795, r8a7796, r8a77970) + r8a7795, r8a7796, r8a77965, r8a77970, r8a77980, r8a77995) + - "extalr" (r8a7795, r8a7796, r8a77965, r8a77970, r8a77980) - "usb_extal" (r8a7743, r8a7745, r8a7790, r8a7791, r8a7793, r8a7794) - #clock-cells: Must be 2 diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt index e71c675ba5da..904ae682ea90 100644 --- a/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt @@ -32,6 +32,7 @@ clock-output-names: - "clkin_i2s" - external I2S clock - optional, - "gmac_clkin" - external GMAC clock - optional - "phy_50m_out" - output clock of the pll in the mac phy + - "hdmi_phy" - output clock of the hdmi phy pll - optional Example: Clock controller node: diff --git a/Documentation/devicetree/bindings/clock/silabs,si544.txt b/Documentation/devicetree/bindings/clock/silabs,si544.txt new file mode 100644 index 000000000000..b86535b80920 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/silabs,si544.txt @@ -0,0 +1,25 @@ +Binding for Silicon Labs 544 programmable I2C clock generator. + +Reference +This binding uses the common clock binding[1]. Details about the device can be +found in the datasheet[2]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Si544 datasheet + https://www.silabs.com/documents/public/data-sheets/si544-datasheet.pdf + +Required properties: + - compatible: One of "silabs,si514a", "silabs,si514b" "silabs,si514c" according + to the speed grade of the chip. + - reg: I2C device address. + - #clock-cells: From common clock bindings: Shall be 0. + +Optional properties: + - clock-output-names: From common clock bindings. Recommended to be "si544". + +Example: + si544: clock-controller@55 { + reg = <0x55>; + #clock-cells = <0>; + compatible = "silabs,si544b"; + }; diff --git a/Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt b/Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt new file mode 100644 index 000000000000..fb9495ea582c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt @@ -0,0 +1,60 @@ +STMicroelectronics STM32 Peripheral Reset Clock Controller +========================================================== + +The RCC IP is both a reset and a clock controller. + +RCC makes also power management (resume/supend and wakeup interrupt). + +Please also refer to reset.txt for common reset controller binding usage. + +Please also refer to clock-bindings.txt for common clock controller +binding usage. + + +Required properties: +- compatible: "st,stm32mp1-rcc", "syscon" +- reg: should be register base and length as documented in the datasheet +- #clock-cells: 1, device nodes should specify the clock in their + "clocks" property, containing a phandle to the clock device node, + an index specifying the clock to use. +- #reset-cells: Shall be 1 +- interrupts: Should contain a general interrupt line and a interrupt line + to the wake-up of processor (CSTOP). + +Example: + rcc: rcc@50000000 { + compatible = "st,stm32mp1-rcc", "syscon"; + reg = <0x50000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + interrupts = <GIC_SPI 5 IRQ_TYPE_NONE>, + <GIC_SPI 145 IRQ_TYPE_NONE>; + }; + +Specifying clocks +================= + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/stm32mp1-clks.h header and can be used in device +tree sources. + +Specifying softreset control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the reset device node and an index specifying +which channel to use. +The index is the bit number within the RCC registers bank, starting from RCC +base address. +It is calculated as: index = register_offset / 4 * 32 + bit_offset. +Where bit_offset is the bit offset within the register. + +For example on STM32MP1, for LTDC reset: + ltdc = APB4_RSTSETR_offset / 4 * 32 + LTDC_bit_offset + = 0x180 / 4 * 32 + 0 = 3072 + +The list of valid indices for STM32MP1 is available in: +include/dt-bindings/reset-controller/stm32mp1-resets.h + +This file implements defines like: +#define LTDC_R 3072 diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt index 4ca21c3a6fc9..460ef27b1008 100644 --- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt +++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt @@ -20,6 +20,7 @@ Required properties : - "allwinner,sun50i-a64-ccu" - "allwinner,sun50i-a64-r-ccu" - "allwinner,sun50i-h5-ccu" + - "allwinner,sun50i-h6-ccu" - "nextthing,gr8-ccu" - reg: Must contain the registers base address and length @@ -31,6 +32,9 @@ Required properties : - #clock-cells : must contain 1 - #reset-cells : must contain 1 +For the main CCU on H6, one more clock is needed: +- "iosc": the SoC's internal frequency oscillator + For the PRCM CCUs on A83T/H3/A64, two more clocks are needed: - "pll-periph": the SoC's peripheral PLL from the main CCU - "iosc": the SoC's internal frequency oscillator diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt b/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt new file mode 100644 index 000000000000..1e03dce99a8f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt @@ -0,0 +1,93 @@ +Binding for TI DA8XX/OMAP-L13X/AM17XX/AM18XX CFGCHIP clocks + +TI DA8XX/OMAP-L13X/AM17XX/AM18XX SoCs contain a general purpose set of +registers call CFGCHIPn. Some of these registers function as clock +gates. This document describes the bindings for those clocks. + +All of the clock nodes described below must be child nodes of a CFGCHIP node +(compatible = "ti,da830-cfgchip"). + +USB PHY clocks +-------------- +Required properties: +- compatible: shall be "ti,da830-usb-phy-clocks". +- #clock-cells: from common clock binding; shall be set to 1. +- clocks: phandles to the parent clocks corresponding to clock-names +- clock-names: shall be "fck", "usb_refclkin", "auxclk" + +This node provides two clocks. The clock at index 0 is the USB 2.0 PHY 48MHz +clock and the clock at index 1 is the USB 1.1 PHY 48MHz clock. + +eHRPWM Time Base Clock (TBCLK) +------------------------------ +Required properties: +- compatible: shall be "ti,da830-tbclksync". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandle to the parent clock +- clock-names: shall be "fck" + +PLL DIV4.5 divider +------------------ +Required properties: +- compatible: shall be "ti,da830-div4p5ena". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandle to the parent clock +- clock-names: shall be "pll0_pllout" + +EMIFA clock source (ASYNC1) +--------------------------- +Required properties: +- compatible: shall be "ti,da850-async1-clksrc". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandles to the parent clocks corresponding to clock-names +- clock-names: shall be "pll0_sysclk3", "div4.5" + +ASYNC3 clock source +------------------- +Required properties: +- compatible: shall be "ti,da850-async3-clksrc". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandles to the parent clocks corresponding to clock-names +- clock-names: shall be "pll0_sysclk2", "pll1_sysclk2" + +Examples: + + cfgchip: syscon@1417c { + compatible = "ti,da830-cfgchip", "syscon", "simple-mfd"; + reg = <0x1417c 0x14>; + + usb_phy_clk: usb-phy-clocks { + compatible = "ti,da830-usb-phy-clocks"; + #clock-cells = <1>; + clocks = <&psc1 1>, <&usb_refclkin>, <&pll0_auxclk>; + clock-names = "fck", "usb_refclkin", "auxclk"; + }; + ehrpwm_tbclk: ehrpwm_tbclk { + compatible = "ti,da830-tbclksync"; + #clock-cells = <0>; + clocks = <&psc1 17>; + clock-names = "fck"; + }; + div4p5_clk: div4.5 { + compatible = "ti,da830-div4p5ena"; + #clock-cells = <0>; + clocks = <&pll0_pllout>; + clock-names = "pll0_pllout"; + }; + async1_clk: async1 { + compatible = "ti,da850-async1-clksrc"; + #clock-cells = <0>; + clocks = <&pll0_sysclk 3>, <&div4p5_clk>; + clock-names = "pll0_sysclk3", "div4.5"; + }; + async3_clk: async3 { + compatible = "ti,da850-async3-clksrc"; + #clock-cells = <0>; + clocks = <&pll0_sysclk 2>, <&pll1_sysclk 2>; + clock-names = "pll0_sysclk2", "pll1_sysclk2"; + }; + }; + +Also see: +- Documentation/devicetree/bindings/clock/clock-bindings.txt + diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt b/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt new file mode 100644 index 000000000000..36998e184821 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt @@ -0,0 +1,96 @@ +Binding for TI DaVinci PLL Controllers + +The PLL provides clocks to most of the components on the SoC. In addition +to the PLL itself, this controller also contains bypasses, gates, dividers, +an multiplexers for various clock signals. + +Required properties: +- compatible: shall be one of: + - "ti,da850-pll0" for PLL0 on DA850/OMAP-L138/AM18XX + - "ti,da850-pll1" for PLL1 on DA850/OMAP-L138/AM18XX +- reg: physical base address and size of the controller's register area. +- clocks: phandles corresponding to the clock names +- clock-names: names of the clock sources - depends on compatible string + - for "ti,da850-pll0", shall be "clksrc", "extclksrc" + - for "ti,da850-pll1", shall be "clksrc" + +Optional properties: +- ti,clkmode-square-wave: Indicates that the the board is supplying a square + wave input on the OSCIN pin instead of using a crystal oscillator. + This property is only valid when compatible = "ti,da850-pll0". + + +Optional child nodes: + +pllout + Describes the main PLL clock output (before POSTDIV). The node name must + be "pllout". + + Required properties: + - #clock-cells: shall be 0 + +sysclk + Describes the PLLDIVn divider clocks that provide the SYSCLKn clock + domains. The node name must be "sysclk". Consumers of this node should + use "n" in "SYSCLKn" as the index parameter for the clock cell. + + Required properties: + - #clock-cells: shall be 1 + +auxclk + Describes the AUXCLK output of the PLL. The node name must be "auxclk". + This child node is only valid when compatible = "ti,da850-pll0". + + Required properties: + - #clock-cells: shall be 0 + +obsclk + Describes the OBSCLK output of the PLL. The node name must be "obsclk". + + Required properties: + - #clock-cells: shall be 0 + + +Examples: + + pll0: clock-controller@11000 { + compatible = "ti,da850-pll0"; + reg = <0x11000 0x1000>; + clocks = <&ref_clk>, <&pll1_sysclk 3>; + clock-names = "clksrc", "extclksrc"; + ti,clkmode-square-wave; + + pll0_pllout: pllout { + #clock-cells = <0>; + }; + + pll0_sysclk: sysclk { + #clock-cells = <1>; + }; + + pll0_auxclk: auxclk { + #clock-cells = <0>; + }; + + pll0_obsclk: obsclk { + #clock-cells = <0>; + }; + }; + + pll1: clock-controller@21a000 { + compatible = "ti,da850-pll1"; + reg = <0x21a000 0x1000>; + clocks = <&ref_clk>; + clock-names = "clksrc"; + + pll0_sysclk: sysclk { + #clock-cells = <1>; + }; + + pll0_obsclk: obsclk { + #clock-cells = <0>; + }; + }; + +Also see: +- Documentation/devicetree/bindings/clock/clock-bindings.txt diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt b/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt new file mode 100644 index 000000000000..dae4ad8e198c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt @@ -0,0 +1,71 @@ +Binding for TI DaVinci Power Sleep Controller (PSC) + +The PSC provides power management, clock gating and reset functionality. It is +primarily used for clocking. + +Required properties: +- compatible: shall be one of: + - "ti,da850-psc0" for PSC0 on DA850/OMAP-L138/AM18XX + - "ti,da850-psc1" for PSC1 on DA850/OMAP-L138/AM18XX +- reg: physical base address and size of the controller's register area +- #clock-cells: from common clock binding; shall be set to 1 +- #power-domain-cells: from generic power domain binding; shall be set to 1. +- clocks: phandles to clocks corresponding to the clock-names property +- clock-names: list of parent clock names - depends on compatible value + - for "ti,da850-psc0", shall be "pll0_sysclk1", "pll0_sysclk2", + "pll0_sysclk4", "pll0_sysclk6", "async1" + - for "ti,da850-psc1", shall be "pll0_sysclk2", "pll0_sysclk4", "async3" + +Optional properties: +- #reset-cells: from reset binding; shall be set to 1 - only applicable when + at least one local domain provides a local reset. + +Consumers: + + Clock, power domain and reset consumers shall use the local power domain + module ID (LPSC) as the index corresponding to the clock cell. Refer to + the device-specific datasheet to find these numbers. NB: Most local + domains only provide a clock/power domain and not a reset. + +Examples: + + psc0: clock-controller@10000 { + compatible = "ti,da850-psc0"; + reg = <0x10000 0x1000>; + #clock-cells = <1>; + #power-domain-cells = <1>; + #reset-cells = <1>; + clocks = <&pll0_sysclk 1>, <&pll0_sysclk 2>, + <&pll0_sysclk 4>, <&pll0_sysclk 6>, <&async1_clk>; + clock_names = "pll0_sysclk1", "pll0_sysclk2", + "pll0_sysclk4", "pll0_sysclk6", "async1"; + }; + psc1: clock-controller@227000 { + compatible = "ti,da850-psc1"; + reg = <0x227000 0x1000>; + #clock-cells = <1>; + #power-domain-cells = <1>; + clocks = <&pll0_sysclk 2>, <&pll0_sysclk 4>, <&async3_clk>; + clock_names = "pll0_sysclk2", "pll0_sysclk4", "async3"; + }; + + /* consumer */ + dsp: dsp@11800000 { + compatible = "ti,da850-dsp"; + reg = <0x11800000 0x40000>, + <0x11e00000 0x8000>, + <0x11f00000 0x8000>, + <0x01c14044 0x4>, + <0x01c14174 0x8>; + reg-names = "l2sram", "l1pram", "l1dram", "host1cfg", "chipsig"; + interrupt-parent = <&intc>; + interrupts = <28>; + clocks = <&psc0 15>; + power-domains = <&psc0 15>; + resets = <&psc0 15>; + }; + +Also see: +- Documentation/devicetree/bindings/clock/clock-bindings.txt +- Documentation/devicetree/bindings/power/power_domain.txt +- Documentation/devicetree/bindings/reset/reset.txt diff --git a/Documentation/devicetree/bindings/clock/ti/divider.txt b/Documentation/devicetree/bindings/clock/ti/divider.txt index 35a6f5c7e5c2..9b13b32974f9 100644 --- a/Documentation/devicetree/bindings/clock/ti/divider.txt +++ b/Documentation/devicetree/bindings/clock/ti/divider.txt @@ -75,6 +75,9 @@ Optional properties: - ti,invert-autoidle-bit : autoidle is enabled by setting the bit to 0, see [2] - ti,set-rate-parent : clk_set_rate is propagated to parent +- ti,latch-bit : latch the divider value to HW, only needed if the register + access requires this. As an example dra76x DPLL_GMAC H14 divider implements + such behavior. Examples: dpll_usb_m2_ck: dpll_usb_m2_ck@4a008190 { diff --git a/Documentation/devicetree/bindings/clock/ti/mux.txt b/Documentation/devicetree/bindings/clock/ti/mux.txt index 2d0d170f8001..eec8994b9be8 100644 --- a/Documentation/devicetree/bindings/clock/ti/mux.txt +++ b/Documentation/devicetree/bindings/clock/ti/mux.txt @@ -48,6 +48,9 @@ Optional properties: zero - ti,set-rate-parent : clk_set_rate is propagated to parent clock, not supported by the composite-mux-clock subtype +- ti,latch-bit : latch the mux value to HW, only needed if the register + access requires this. As an example, dra7x DPLL_GMAC H14 muxing + implements such behavior. Examples: |