diff options
Diffstat (limited to 'Documentation/devicetree')
6 files changed, 117 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt index 49fc7ada929a..3545ea704b50 100644 --- a/Documentation/devicetree/bindings/arm/davinci/nand.txt +++ b/Documentation/devicetree/bindings/arm/davinci/nand.txt @@ -23,6 +23,9 @@ Recommended properties : - ti,davinci-nand-buswidth: buswidth 8 or 16 - ti,davinci-nand-use-bbt: use flash based bad block table support. +nand device bindings may contain additional sub-nodes describing +partitions of the address space. See partition.txt for more detail. + Example(da850 EVM ): nand_cs3@62000000 { compatible = "ti,davinci-nand"; @@ -35,4 +38,9 @@ nand_cs3@62000000 { ti,davinci-ecc-mode = "hw"; ti,davinci-ecc-bits = <4>; ti,davinci-nand-use-bbt; + + partition@180000 { + label = "ubifs"; + reg = <0x180000 0x7e80000>; + }; }; diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt b/Documentation/devicetree/bindings/mtd/denali-nand.txt new file mode 100644 index 000000000000..b04d03a1d499 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt @@ -0,0 +1,23 @@ +* Denali NAND controller + +Required properties: + - compatible : should be "denali,denali-nand-dt" + - reg : should contain registers location and length for data and reg. + - reg-names: Should contain the reg names "nand_data" and "denali_reg" + - interrupts : The interrupt number. + - dm-mask : DMA bit mask + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Examples: + +nand: nand@ff900000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "denali,denali-nand-dt"; + reg = <0xff900000 0x100000>, <0xffb80000 0x10000>; + reg-names = "nand_data", "denali_reg"; + interrupts = <0 144 4>; + dma-mask = <0xffffffff>; +}; diff --git a/Documentation/devicetree/bindings/mtd/flctl-nand.txt b/Documentation/devicetree/bindings/mtd/flctl-nand.txt new file mode 100644 index 000000000000..427f46dc60ad --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/flctl-nand.txt @@ -0,0 +1,49 @@ +FLCTL NAND controller + +Required properties: +- compatible : "renesas,shmobile-flctl-sh7372" +- reg : Address range of the FLCTL +- interrupts : flste IRQ number +- nand-bus-width : bus width to NAND chip + +Optional properties: +- dmas: DMA specifier(s) +- dma-names: name for each DMA specifier. Valid names are + "data_tx", "data_rx", "ecc_tx", "ecc_rx" + +The DMA fields are not used yet in the driver but are listed here for +completing the bindings. + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Example: + + flctl@e6a30000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "renesas,shmobile-flctl-sh7372"; + reg = <0xe6a30000 0x100>; + interrupts = <0x0d80>; + + nand-bus-width = <16>; + + dmas = <&dmac 1 /* data_tx */ + &dmac 2;> /* data_rx */ + dma-names = "data_tx", "data_rx"; + + system@0 { + label = "system"; + reg = <0x0 0x8000000>; + }; + + userdata@8000000 { + label = "userdata"; + reg = <0x8000000 0x10000000>; + }; + + cache@18000000 { + label = "cache"; + reg = <0x18000000 0x8000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt index e2c663b354d2..e3ea32e7de3e 100644 --- a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt @@ -3,9 +3,7 @@ Required properties: - compatible : "st,spear600-fsmc-nand" - reg : Address range of the mtd chip -- reg-names: Should contain the reg names "fsmc_regs" and "nand_data" -- st,ale-off : Chip specific offset to ALE -- st,cle-off : Chip specific offset to CLE +- reg-names: Should contain the reg names "fsmc_regs", "nand_data", "nand_addr" and "nand_cmd" Optional properties: - bank-width : Width (in bytes) of the device. If not present, the width @@ -19,10 +17,10 @@ Example: #address-cells = <1>; #size-cells = <1>; reg = <0xd1800000 0x1000 /* FSMC Register */ - 0xd2000000 0x4000>; /* NAND Base */ - reg-names = "fsmc_regs", "nand_data"; - st,ale-off = <0x20000>; - st,cle-off = <0x10000>; + 0xd2000000 0x0010 /* NAND Base DATA */ + 0xd2020000 0x0010 /* NAND Base ADDR */ + 0xd2010000 0x0010>; /* NAND Base CMD */ + reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd"; bank-width = <1>; nand-skip-bbtscan; diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/m25p80.txt new file mode 100644 index 000000000000..6d3d57609470 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/m25p80.txt @@ -0,0 +1,29 @@ +* MTD SPI driver for ST M25Pxx (and similar) serial flash chips + +Required properties: +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. +- compatible : Should be the manufacturer and the name of the chip. Bear in mind + the DT binding is not Linux-only, but in case of Linux, see the + "m25p_ids" table in drivers/mtd/devices/m25p80.c for the list of + supported chips. +- reg : Chip-Select number +- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at + +Optional properties: +- m25p,fast-read : Use the "fast read" opcode to read data from the chip instead + of the usual "read" opcode. This opcode is not supported by + all chips and support for it can not be detected at runtime. + Refer to your chips' datasheet to check if this is supported + by your chip. + +Example: + + flash: m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,m25p80"; + reg = <0>; + spi-max-frequency = <40000000>; + m25p,fast-read; + }; diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt index 94de19b8f16b..dab7847fc800 100644 --- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -23,6 +23,9 @@ file systems on embedded devices. unaligned accesses as implemented in the JFFS2 code via memcpy(). By defining "no-unaligned-direct-access", the flash will not be exposed directly to the MTD users (e.g. JFFS2) any more. + - linux,mtd-name: allow to specify the mtd name for retro capability with + physmap-flash drivers as boot loader pass the mtd partition via the old + device name physmap-flash. For JEDEC compatible devices, the following additional properties are defined: |