diff options
Diffstat (limited to 'Documentation/devicetree')
5 files changed, 111 insertions, 6 deletions
diff --git a/Documentation/devicetree/bindings/power/reset/qcom,pon.txt b/Documentation/devicetree/bindings/power/reset/qcom,pon.txt new file mode 100644 index 000000000000..651491bb63b7 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/qcom,pon.txt @@ -0,0 +1,45 @@ +Qualcomm PON Device + +The Power On device for Qualcomm PM8xxx is MFD supporting pwrkey +and resin along with the Android reboot-mode. + +This DT node has pwrkey and resin as sub nodes. + +Required Properties: +-compatible: "qcom,pm8916-pon" +-reg: Specifies the physical address of the pon register + +Optional subnode: +-pwrkey: Specifies the subnode pwrkey and should follow the + qcom,pm8941-pwrkey.txt description. +-resin: Specifies the subnode resin and should follow the + qcom,pm8xxx-pwrkey.txt description. + +The rest of the properties should follow the generic reboot-mode description +found in reboot-mode.txt + +Example: + + pon@800 { + compatible = "qcom,pm8916-pon"; + + reg = <0x800>; + mode-bootloader = <0x2>; + mode-recovery = <0x1>; + + pwrkey { + compatible = "qcom,pm8941-pwrkey"; + interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + linux,code = <KEY_POWER>; + }; + + resin { + compatible = "qcom,pm8941-resin"; + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + linux,code = <KEY_VOLUMEDOWN>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt b/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt new file mode 100644 index 000000000000..55967a0bee11 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt @@ -0,0 +1,26 @@ +Devicetree bindings for Maxim DS2760 +==================================== + +The ds2760 is a w1 slave device and must hence have its sub-node in DT +under a w1 bus master node. + +The device exposes a power supply, so the details described in +Documentation/devicetree/bindings/power/supply/power_supply.txt apply. + +Required properties: +- compatible: must be "maxim,ds2760" + +Optional properties: +- power-supplies: Refers to one or more power supplies connected to + this battery. +- maxim,pmod-enabled: This boolean property enables the DS2760 to enter + sleep mode when the DQ line goes low for greater + than 2 seconds and leave sleep Mode when the DQ + line goes high. +- maxim,cache-time-ms: Time im milliseconds to cache the data for. When + this time expires, the values are read again from + the hardware. Defaults to 1000. +- rated-capacity-microamp-hours: + The rated capacity of the battery, in mAh. + If not specified, the value stored in the + non-volatile chip memory is used. diff --git a/Documentation/devicetree/bindings/power/supply/sbs_sbs-battery.txt b/Documentation/devicetree/bindings/power/supply/sbs_sbs-battery.txt index c40e8926facf..4e78e51018eb 100644 --- a/Documentation/devicetree/bindings/power/supply/sbs_sbs-battery.txt +++ b/Documentation/devicetree/bindings/power/supply/sbs_sbs-battery.txt @@ -2,7 +2,11 @@ SBS sbs-battery ~~~~~~~~~~ Required properties : - - compatible : "sbs,sbs-battery" + - compatible: "<vendor>,<part-number>", "sbs,sbs-battery" as fallback. The + part number compatible string might be used in order to take care of + vendor specific registers. + Known <vendor>,<part-number>: + ti,bq20z75 Optional properties : - sbs,i2c-retry-count : The number of times to retry i2c transactions on i2c @@ -14,9 +18,9 @@ Optional properties : Example: - bq20z75@b { - compatible = "sbs,sbs-battery"; - reg = < 0xb >; + battery@b { + compatible = "ti,bq20z75", "sbs,sbs-battery"; + reg = <0xb>; sbs,i2c-retry-count = <2>; sbs,poll-retry-count = <10>; sbs,battery-detect-gpios = <&gpio-controller 122 1>; diff --git a/Documentation/devicetree/bindings/w1/w1-gpio.txt b/Documentation/devicetree/bindings/w1/w1-gpio.txt index 37091902a021..3d6554eac240 100644 --- a/Documentation/devicetree/bindings/w1/w1-gpio.txt +++ b/Documentation/devicetree/bindings/w1/w1-gpio.txt @@ -13,10 +13,15 @@ Optional properties: - linux,open-drain: if specified, the data pin is considered in open-drain mode. +Also refer to the generic w1.txt document. + Examples: onewire { compatible = "w1-gpio"; - gpios = <&gpio 126 0>, <&gpio 105 0>; - }; + gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + battery { + // ... + }; + }; diff --git a/Documentation/devicetree/bindings/w1/w1.txt b/Documentation/devicetree/bindings/w1/w1.txt new file mode 100644 index 000000000000..05f26b27d898 --- /dev/null +++ b/Documentation/devicetree/bindings/w1/w1.txt @@ -0,0 +1,25 @@ +Generic devicetree bindings for onewire (w1) busses +=================================================== + +Onewire busses are described through nodes of their master bus controller. +Slave devices are listed as sub-nodes of such master devices. For now, only +one slave is allowed per bus master. + + +Example: + + charger: charger { + compatible = "gpio-charger"; + charger-type = "mains"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + }; + + onewire { + compatible = "w1-gpio"; + gpios = <&gpio 100 0>, <&gpio 101 0>; + + battery { + compatible = "maxim,ds2760"; + power-supplies = <&charger>; + }; + }; |