diff options
Diffstat (limited to 'Documentation/devicetree')
19 files changed, 201 insertions, 27 deletions
diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt index bdadc3da9556..6970f30a3770 100644 --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -66,7 +66,7 @@ Required root node properties: - "insignal,arndale-octa" - for Exynos5420-based Insignal Arndale Octa board. - "insignal,origen" - for Exynos4210-based Insignal Origen board. - - "insignal,origen4412 - for Exynos4412-based Insignal Origen board. + - "insignal,origen4412" - for Exynos4412-based Insignal Origen board. Optional nodes: diff --git a/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt index 6fddb4f4f71a..3055d5c2c04e 100644 --- a/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt +++ b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt @@ -36,7 +36,7 @@ Optional nodes: - port/ports: to describe a connection to an external encoder. The binding follows Documentation/devicetree/bindings/graph.txt and - suppors a single port with a single endpoint. + supports a single port with a single endpoint. - See also Documentation/devicetree/bindings/display/tilcdc/panel.txt and Documentation/devicetree/bindings/display/tilcdc/tfp410.txt for connecting diff --git a/Documentation/devicetree/bindings/gpio/nintendo,hollywood-gpio.txt b/Documentation/devicetree/bindings/gpio/nintendo,hollywood-gpio.txt index 20fc72d9e61e..45a61b462287 100644 --- a/Documentation/devicetree/bindings/gpio/nintendo,hollywood-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/nintendo,hollywood-gpio.txt @@ -1,7 +1,7 @@ Nintendo Wii (Hollywood) GPIO controller Required properties: -- compatible: "nintendo,hollywood-gpio +- compatible: "nintendo,hollywood-gpio" - reg: Physical base address and length of the controller's registers. - gpio-controller: Marks the device node as a GPIO controller. - #gpio-cells: Should be <2>. The first cell is the pin number and the diff --git a/Documentation/devicetree/bindings/input/touchscreen/hideep.txt b/Documentation/devicetree/bindings/input/touchscreen/hideep.txt index 121d9b7c79a2..1063c30d53f7 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/hideep.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/hideep.txt @@ -32,7 +32,7 @@ i2c@00000000 { reg = <0x6c>; interrupt-parent = <&gpx1>; interrupts = <2 IRQ_TYPE_LEVEL_LOW>; - vdd-supply = <&ldo15_reg>"; + vdd-supply = <&ldo15_reg>; vid-supply = <&ldo18_reg>; reset-gpios = <&gpx1 5 0>; touchscreen-size-x = <1080>; diff --git a/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt b/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt index 1099fe0788fa..f246ccbf8838 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt @@ -15,7 +15,7 @@ Required properties: include "nvidia,tegra30-ictlr". - reg : Specifies base physical address and size of the registers. Each controller must be described separately (Tegra20 has 4 of them, - whereas Tegra30 and later have 5" + whereas Tegra30 and later have 5). - interrupt-controller : Identifies the node as an interrupt controller. - #interrupt-cells : Specifies the number of cells needed to encode an interrupt source. The value must be 3. diff --git a/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt index 136bd612bd83..6a36bf66d932 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt @@ -12,7 +12,7 @@ Required properties: specifier, shall be 2 - interrupts: interrupts references to primary interrupt controller (only needed for exti controller with multiple exti under - same parent interrupt: st,stm32-exti and st,stm32h7-exti") + same parent interrupt: st,stm32-exti and st,stm32h7-exti) Example: diff --git a/Documentation/devicetree/bindings/mips/brcm/soc.txt b/Documentation/devicetree/bindings/mips/brcm/soc.txt index 356c29789cf5..3a66d3c483e1 100644 --- a/Documentation/devicetree/bindings/mips/brcm/soc.txt +++ b/Documentation/devicetree/bindings/mips/brcm/soc.txt @@ -152,7 +152,7 @@ Required properties: - compatible : should contain one of: "brcm,bcm7425-timers" "brcm,bcm7429-timers" - "brcm,bcm7435-timers and + "brcm,bcm7435-timers" and "brcm,brcmstb-timers" - reg : the timers register range - interrupts : the interrupt line for this timer block diff --git a/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt b/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt index dfe287a5d6f2..b58843f29591 100644 --- a/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt +++ b/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt @@ -13,14 +13,17 @@ MDIO multiplexer node: Every non-ethernet PHY requires a compatible so that it could be probed based on this compatible string. +Optional properties: +- clocks: phandle of the core clock which drives the mdio block. + Additional information regarding generic multiplexer properties can be found at- Documentation/devicetree/bindings/net/mdio-mux.txt for example: - mdio_mux_iproc: mdio-mux@6602023c { + mdio_mux_iproc: mdio-mux@66020000 { compatible = "brcm,mdio-mux-iproc"; - reg = <0x6602023c 0x14>; + reg = <0x66020000 0x250>; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/net/can/xilinx_can.txt b/Documentation/devicetree/bindings/net/can/xilinx_can.txt index fe38847d8e26..ae5c07e96ad5 100644 --- a/Documentation/devicetree/bindings/net/can/xilinx_can.txt +++ b/Documentation/devicetree/bindings/net/can/xilinx_can.txt @@ -2,20 +2,26 @@ Xilinx Axi CAN/Zynq CANPS controller Device Tree Bindings --------------------------------------------------------- Required properties: -- compatible : Should be "xlnx,zynq-can-1.0" for Zynq CAN - controllers and "xlnx,axi-can-1.00.a" for Axi CAN - controllers. -- reg : Physical base address and size of the Axi CAN/Zynq - CANPS registers map. +- compatible : Should be: + - "xlnx,zynq-can-1.0" for Zynq CAN controllers + - "xlnx,axi-can-1.00.a" for Axi CAN controllers + - "xlnx,canfd-1.0" for CAN FD controllers +- reg : Physical base address and size of the controller + registers map. - interrupts : Property with a value describing the interrupt number. - interrupt-parent : Must be core interrupt controller -- clock-names : List of input clock names - "can_clk", "pclk" - (For CANPS), "can_clk" , "s_axi_aclk"(For AXI CAN) +- clock-names : List of input clock names + - "can_clk", "pclk" (For CANPS), + - "can_clk", "s_axi_aclk" (For AXI CAN and CAN FD). (See clock bindings for details). - clocks : Clock phandles (see clock bindings for details). -- tx-fifo-depth : Can Tx fifo depth. -- rx-fifo-depth : Can Rx fifo depth. +- tx-fifo-depth : Can Tx fifo depth (Zynq, Axi CAN). +- rx-fifo-depth : Can Rx fifo depth (Zynq, Axi CAN, CAN FD in + sequential Rx mode). +- tx-mailbox-count : Can Tx mailbox buffer count (CAN FD). +- rx-mailbox-count : Can Rx mailbox buffer count (CAN FD in mailbox Rx + mode). Example: @@ -42,3 +48,14 @@ For Axi CAN Dts file: tx-fifo-depth = <0x40>; rx-fifo-depth = <0x40>; }; +For CAN FD Dts file: + canfd_0: canfd@40000000 { + compatible = "xlnx,canfd-1.0"; + clocks = <&clkc 0>, <&clkc 1>; + clock-names = "can_clk", "s_axi_aclk"; + reg = <0x40000000 0x2000>; + interrupt-parent = <&intc>; + interrupts = <0 59 1>; + tx-mailbox-count = <0x20>; + rx-fifo-depth = <0x20>; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt new file mode 100644 index 000000000000..b6ae8541bd55 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt @@ -0,0 +1,153 @@ +Realtek SMI-based Switches +========================== + +The SMI "Simple Management Interface" is a two-wire protocol using +bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does +not use the MDIO protocol. This binding defines how to specify the +SMI-based Realtek devices. + +Required properties: + +- compatible: must be exactly one of: + "realtek,rtl8366" + "realtek,rtl8366rb" (4+1 ports) + "realtek,rtl8366s" (4+1 ports) + "realtek,rtl8367" + "realtek,rtl8367b" + "realtek,rtl8368s" (8 port) + "realtek,rtl8369" + "realtek,rtl8370" (8 port) + +Required properties: +- mdc-gpios: GPIO line for the MDC clock line. +- mdio-gpios: GPIO line for the MDIO data line. +- reset-gpios: GPIO line for the reset signal. + +Optional properties: +- realtek,disable-leds: if the LED drivers are not used in the + hardware design this will disable them so they are not turned on + and wasting power. + +Required subnodes: + +- interrupt-controller + + This defines an interrupt controller with an IRQ line (typically + a GPIO) that will demultiplex and handle the interrupt from the single + interrupt line coming out of one of the SMI-based chips. It most + importantly provides link up/down interrupts to the PHY blocks inside + the ASIC. + +Required properties of interrupt-controller: + +- interrupt: parent interrupt, see interrupt-controller/interrupts.txt +- interrupt-controller: see interrupt-controller/interrupts.txt +- #address-cells: should be <0> +- #interrupt-cells: should be <1> + +- mdio + + This defines the internal MDIO bus of the SMI device, mostly for the + purpose of being able to hook the interrupts to the right PHY and + the right PHY to the corresponding port. + +Required properties of mdio: + +- compatible: should be set to "realtek,smi-mdio" for all SMI devices + +See net/mdio.txt for additional MDIO bus properties. + +See net/dsa/dsa.txt for a list of additional required and optional properties +and subnodes of DSA switches. + +Examples: + +switch { + compatible = "realtek,rtl8366rb"; + /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */ + mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; + mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + + switch_intc: interrupt-controller { + /* GPIO 15 provides the interrupt */ + interrupt-parent = <&gpio0>; + interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + port@0 { + reg = <0>; + label = "lan0"; + phy-handle = <&phy0>; + }; + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&phy1>; + }; + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&phy2>; + }; + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&phy3>; + }; + port@4 { + reg = <4>; + label = "wan"; + phy-handle = <&phy4>; + }; + port@5 { + reg = <5>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + mdio { + compatible = "realtek,smi-mdio", "dsa-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + phy0: phy@0 { + reg = <0>; + interrupt-parent = <&switch_intc>; + interrupts = <0>; + }; + phy1: phy@1 { + reg = <1>; + interrupt-parent = <&switch_intc>; + interrupts = <1>; + }; + phy2: phy@2 { + reg = <2>; + interrupt-parent = <&switch_intc>; + interrupts = <2>; + }; + phy3: phy@3 { + reg = <3>; + interrupt-parent = <&switch_intc>; + interrupts = <3>; + }; + phy4: phy@4 { + reg = <4>; + interrupt-parent = <&switch_intc>; + interrupts = <12>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/fsl-fman.txt b/Documentation/devicetree/bindings/net/fsl-fman.txt index 74603dd0789e..299c0dcd67db 100644 --- a/Documentation/devicetree/bindings/net/fsl-fman.txt +++ b/Documentation/devicetree/bindings/net/fsl-fman.txt @@ -238,7 +238,7 @@ PROPERTIES Must include one of the following: - "fsl,fman-dtsec" for dTSEC MAC - "fsl,fman-xgec" for XGEC MAC - - "fsl,fman-memac for mEMAC MAC + - "fsl,fman-memac" for mEMAC MAC - cell-index Usage: required diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt index 9b387f861aed..7dec508987c7 100644 --- a/Documentation/devicetree/bindings/power/power_domain.txt +++ b/Documentation/devicetree/bindings/power/power_domain.txt @@ -133,7 +133,7 @@ located inside a PM domain with index 0 of a power controller represented by a node with the label "power". In the second example the consumer device are partitioned across two PM domains, the first with index 0 and the second with index 1, of a power controller that -is represented by a node with the label "power. +is represented by a node with the label "power". Optional properties: - required-opps: This contains phandle to an OPP node in another device's OPP diff --git a/Documentation/devicetree/bindings/regulator/tps65090.txt b/Documentation/devicetree/bindings/regulator/tps65090.txt index ca69f5e3040c..ae326f263597 100644 --- a/Documentation/devicetree/bindings/regulator/tps65090.txt +++ b/Documentation/devicetree/bindings/regulator/tps65090.txt @@ -16,7 +16,7 @@ Required properties: Optional properties: - ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3. If DCDCs are externally controlled then this property should be there. -- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3. +- dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3. If DCDCs are externally controlled and if it is from GPIO then GPIO number should be provided. If it is externally controlled and no GPIO entry then driver will just configure this rails as external control diff --git a/Documentation/devicetree/bindings/reset/st,sti-softreset.txt b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt index a21658f18fe6..3661e6153a92 100644 --- a/Documentation/devicetree/bindings/reset/st,sti-softreset.txt +++ b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt @@ -15,7 +15,7 @@ Please refer to reset.txt in this directory for common reset controller binding usage. Required properties: -- compatible: Should be st,stih407-softreset"; +- compatible: Should be "st,stih407-softreset"; - #reset-cells: 1, see below example: diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt index d330c73de9a2..68b7d6207e3d 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt @@ -39,7 +39,7 @@ Required properties: Optional property: - clock-frequency: Desired I2C bus clock frequency in Hz. - When missing default to 400000Hz. + When missing default to 100000Hz. Child nodes should conform to I2C bus binding as described in i2c.txt. diff --git a/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt b/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt index 6a4aadc4ce06..84b28dbe9f15 100644 --- a/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt +++ b/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt @@ -30,7 +30,7 @@ Required properties: Board connectors: * Headset Mic - * Secondary Mic", + * Secondary Mic * DMIC * Ext Spk diff --git a/Documentation/devicetree/bindings/sound/qcom,apq8096.txt b/Documentation/devicetree/bindings/sound/qcom,apq8096.txt index aa54e49fc8a2..c7600a93ab39 100644 --- a/Documentation/devicetree/bindings/sound/qcom,apq8096.txt +++ b/Documentation/devicetree/bindings/sound/qcom,apq8096.txt @@ -35,7 +35,7 @@ This binding describes the APQ8096 sound card, which uses qdsp for audio. "Digital Mic3" Audio pins and MicBias on WCD9335 Codec: - "MIC_BIAS1 + "MIC_BIAS1" "MIC_BIAS2" "MIC_BIAS3" "MIC_BIAS4" diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt index 252a05c5d976..c8c4b00ecb94 100644 --- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt @@ -16,7 +16,8 @@ A child node must exist to represent the core DWC3 IP block. The name of the node is not important. The content of the node is defined in dwc3.txt. Phy documentation is provided in the following places: -Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt +Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt - USB2.0 PHY +Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt - Type-C PHY Example device nodes: diff --git a/Documentation/devicetree/bindings/w1/w1-gpio.txt b/Documentation/devicetree/bindings/w1/w1-gpio.txt index 6e09c35d9f1a..37091902a021 100644 --- a/Documentation/devicetree/bindings/w1/w1-gpio.txt +++ b/Documentation/devicetree/bindings/w1/w1-gpio.txt @@ -15,7 +15,7 @@ Optional properties: Examples: - onewire@0 { + onewire { compatible = "w1-gpio"; gpios = <&gpio 126 0>, <&gpio 105 0>; }; |