diff options
Diffstat (limited to 'Documentation/devicetree/bindings/spi')
7 files changed, 126 insertions, 10 deletions
diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt index 8bc95e2fc47f..31b5b21598ff 100644 --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -23,6 +23,12 @@ See the clock consumer binding, Obsolete properties: - fsl,spi-num-chipselects : Contains the number of the chipselect +Optional properties: +- fsl,spi-rdy-drctl: Integer, representing the value of DRCTL, the register +controlling the SPI_READY handling. Note that to enable the DRCTL consideration, +the SPI_READY mode-flag needs to be set too. +Valid values are: 0 (disabled), 1 (edge-triggered burst) and 2 (level-triggered burst). + Example: ecspi@70010000 { @@ -35,4 +41,5 @@ ecspi@70010000 { <&gpio3 25 0>; /* GPIO3_25 */ dmas = <&sdma 3 7 1>, <&sdma 4 7 2>; dma-names = "rx", "tx"; + fsl,spi-rdy-drctl = <1>; }; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index da6614c63796..dc975064fa27 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -1,17 +1,23 @@ Renesas MSIOF spi controller Required properties: -- compatible : "renesas,msiof-<soctype>" for SoCs, - "renesas,sh-msiof" for SuperH, or - "renesas,sh-mobile-msiof" for SH Mobile series. - Examples with soctypes are: - "renesas,msiof-r8a7790" (R-Car H2) +- compatible : "renesas,msiof-r8a7790" (R-Car H2) "renesas,msiof-r8a7791" (R-Car M2-W) "renesas,msiof-r8a7792" (R-Car V2H) "renesas,msiof-r8a7793" (R-Car M2-N) "renesas,msiof-r8a7794" (R-Car E2) "renesas,msiof-r8a7796" (R-Car M3-W) "renesas,msiof-sh73a0" (SH-Mobile AG5) + "renesas,sh-mobile-msiof" (generic SH-Mobile compatibile device) + "renesas,rcar-gen2-msiof" (generic R-Car Gen2 compatible device) + "renesas,rcar-gen3-msiof" (generic R-Car Gen3 compatible device) + "renesas,sh-msiof" (deprecated) + + When compatible with the generic version, nodes + must list the SoC-specific version corresponding + to the platform first followed by the generic + version. + - reg : A list of offsets and lengths of the register sets for the device. If only one register set is present, it is to be used @@ -61,7 +67,8 @@ Documentation/devicetree/bindings/pinctrl/renesas,*. Example: msiof0: spi@e6e20000 { - compatible = "renesas,msiof-r8a7791"; + compatible = "renesas,msiof-r8a7791", + "renesas,rcar-gen2-msiof"; reg = <0 0xe6e20000 0 0x0064>; interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>; diff --git a/Documentation/devicetree/bindings/spi/spi-bcm63xx-hsspi.txt b/Documentation/devicetree/bindings/spi/spi-bcm63xx-hsspi.txt new file mode 100644 index 000000000000..37b29ee13860 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-bcm63xx-hsspi.txt @@ -0,0 +1,33 @@ +Binding for Broadcom BCM6328 High Speed SPI controller + +Required properties: +- compatible: must contain of "brcm,bcm6328-hsspi". +- reg: Base address and size of the controllers memory area. +- interrupts: Interrupt for the SPI block. +- clocks: phandles of the SPI clock and the PLL clock. +- clock-names: must be "hsspi", "pll". +- #address-cells: <1>, as required by generic SPI binding. +- #size-cells: <0>, also as required by generic SPI binding. + +Optional properties: +- num-cs: some controllers have less than 8 cs signals. Defaults to 8 + if absent. + +Child nodes as per the generic SPI binding. + +Example: + + spi@10001000 { + compatible = "brcm,bcm6328-hsspi"; + reg = <0x10001000 0x600>; + + interrupts = <29>; + + clocks = <&clkctl 9>, <&hsspi_pll>; + clock-names = "hsspi", "pll"; + + num-cs = <2>; + + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-bcm63xx.txt b/Documentation/devicetree/bindings/spi/spi-bcm63xx.txt new file mode 100644 index 000000000000..1c16f6692613 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-bcm63xx.txt @@ -0,0 +1,33 @@ +Binding for Broadcom BCM6348/BCM6358 SPI controller + +Required properties: +- compatible: must contain one of "brcm,bcm6348-spi", "brcm,bcm6358-spi". +- reg: Base address and size of the controllers memory area. +- interrupts: Interrupt for the SPI block. +- clocks: phandle of the SPI clock. +- clock-names: has to be "spi". +- #address-cells: <1>, as required by generic SPI binding. +- #size-cells: <0>, also as required by generic SPI binding. + +Optional properties: +- num-cs: some controllers have less than 8 cs signals. Defaults to 8 + if absent. + +Child nodes as per the generic SPI binding. + +Example: + + spi@10000800 { + compatible = "brcm,bcm6368-spi", "brcm,bcm6358-spi"; + reg = <0x10000800 0x70c>; + + interrupts = <1>; + + clocks = <&clkctl 9>; + clock-names = "spi"; + + num-cs = <5>; + + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt b/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt new file mode 100644 index 000000000000..6069b95a883d --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt @@ -0,0 +1,29 @@ +Lantiq Synchronous Serial Controller (SSC) SPI master driver + +Required properties: +- compatible: "lantiq,ase-spi", "lantiq,falcon-spi", "lantiq,xrx100-spi" +- #address-cells: see spi-bus.txt +- #size-cells: see spi-bus.txt +- reg: address and length of the spi master registers +- interrupts: should contain the "spi_rx", "spi_tx" and "spi_err" interrupt. + + +Optional properties: +- clocks: spi clock phandle +- num-cs: see spi-bus.txt, set to 8 if unset +- base-cs: the number of the first chip select, set to 1 if unset. + +Example: + + +spi: spi@E100800 { + compatible = "lantiq,xrx200-spi", "lantiq,xrx100-spi"; + reg = <0xE100800 0x100>; + interrupt-parent = <&icu0>; + interrupts = <22 23 24>; + interrupt-names = "spi_rx", "spi_tx", "spi_err"; + #address-cells = <1>; + #size-cells = <1>; + num-cs = <6>; + base-cs = <1>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt index d2ca153614f9..83da4931d832 100644 --- a/Documentation/devicetree/bindings/spi/spi-rockchip.txt +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt @@ -31,6 +31,10 @@ Optional Properties: - rx-sample-delay-ns: nanoseconds to delay after the SCLK edge before sampling Rx data (may need to be fine tuned for high capacitance lines). No delay (0) by default. +- pinctrl-names: Names for the pin configuration(s); may be "default" or + "sleep", where the "sleep" configuration may describe the state + the pins should be in during system suspend. See also + pinctrl/pinctrl-bindings.txt. Example: @@ -46,4 +50,7 @@ Example: interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>; clock-names = "spiclk", "apb_pclk"; + pinctrl-0 = <&spi1_pins>; + pinctrl-1 = <&spi1_sleep>; + pinctrl-names = "default", "sleep"; }; diff --git a/Documentation/devicetree/bindings/spi/spi_pl022.txt b/Documentation/devicetree/bindings/spi/spi_pl022.txt index 4d1673ca8cf8..7638b4968ddb 100644 --- a/Documentation/devicetree/bindings/spi/spi_pl022.txt +++ b/Documentation/devicetree/bindings/spi/spi_pl022.txt @@ -30,7 +30,10 @@ contain the following properties. 0: SPI 1: Texas Instruments Synchronous Serial Frame Format 2: Microwire (Half Duplex) -- pl022,com-mode : polling, interrupt or dma +- pl022,com-mode : specifies the transfer mode: + 0: interrupt mode + 1: polling mode (default mode if property not present) + 2: DMA mode - pl022,rx-level-trig : Rx FIFO watermark level - pl022,tx-level-trig : Tx FIFO watermark level - pl022,ctrl-len : Microwire interface: Control length @@ -56,9 +59,7 @@ Example: spi-max-frequency = <12000000>; spi-cpol; spi-cpha; - pl022,hierarchy = <0>; pl022,interface = <0>; - pl022,slave-tx-disable; pl022,com-mode = <0x2>; pl022,rx-level-trig = <0>; pl022,tx-level-trig = <0>; @@ -67,4 +68,3 @@ Example: pl022,duplex = <0>; }; }; - |