diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/amd-xgbe.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/net/amd-xgbe.txt | 40 |
1 files changed, 35 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/net/amd-xgbe.txt b/Documentation/devicetree/bindings/net/amd-xgbe.txt index 26efd526d16c..4bb624a73b54 100644 --- a/Documentation/devicetree/bindings/net/amd-xgbe.txt +++ b/Documentation/devicetree/bindings/net/amd-xgbe.txt @@ -5,12 +5,16 @@ Required properties: - reg: Address and length of the register sets for the device - MAC registers - PCS registers + - SerDes Rx/Tx registers + - SerDes integration registers (1/2) + - SerDes integration registers (2/2) - interrupt-parent: Should be the phandle for the interrupt controller that services interrupts for this device - interrupts: Should contain the amd-xgbe interrupt(s). The first interrupt listed is required and is the general device interrupt. If the optional amd,per-channel-interrupt property is specified, then one additional - interrupt for each DMA channel supported by the device should be specified + interrupt for each DMA channel supported by the device should be specified. + The last interrupt listed should be the PCS auto-negotiation interrupt. - clocks: - DMA clock for the amd-xgbe device (used for calculating the correct Rx interrupt watchdog timer value on a DMA channel @@ -19,7 +23,6 @@ Required properties: - clock-names: Should be the names of the clocks - "dma_clk" for the DMA clock - "ptp_clk" for the PTP clock -- phy-handle: See ethernet.txt file in the same directory - phy-mode: See ethernet.txt file in the same directory Optional properties: @@ -29,19 +32,46 @@ Optional properties: - amd,per-channel-interrupt: Indicates that Rx and Tx complete will generate a unique interrupt for each DMA channel - this requires an additional interrupt be configured for each DMA channel +- amd,speed-set: Speed capabilities of the device + 0 - 1GbE and 10GbE (default) + 1 - 2.5GbE and 10GbE + +The following optional properties are represented by an array with each +value corresponding to a particular speed. The first array value represents +the setting for the 1GbE speed, the second value for the 2.5GbE speed and +the third value for the 10GbE speed. All three values are required if the +property is used. +- amd,serdes-blwc: Baseline wandering correction enablement + 0 - Off + 1 - On +- amd,serdes-cdr-rate: CDR rate speed selection +- amd,serdes-pq-skew: PQ (data sampling) skew +- amd,serdes-tx-amp: TX amplitude boost +- amd,serdes-dfe-tap-config: DFE taps available to run +- amd,serdes-dfe-tap-enable: DFE taps to enable Example: xgbe@e0700000 { compatible = "amd,xgbe-seattle-v1a"; reg = <0 0xe0700000 0 0x80000>, - <0 0xe0780000 0 0x80000>; + <0 0xe0780000 0 0x80000>, + <0 0xe1240800 0 0x00400>, + <0 0xe1250000 0 0x00060>, + <0 0xe1250080 0 0x00004>; interrupt-parent = <&gic>; interrupts = <0 325 4>, - <0 326 1>, <0 327 1>, <0 328 1>, <0 329 1>; + <0 326 1>, <0 327 1>, <0 328 1>, <0 329 1>, + <0 323 4>; amd,per-channel-interrupt; clocks = <&xgbe_dma_clk>, <&xgbe_ptp_clk>; clock-names = "dma_clk", "ptp_clk"; - phy-handle = <&phy>; phy-mode = "xgmii"; mac-address = [ 02 a1 a2 a3 a4 a5 ]; + amd,speed-set = <0>; + amd,serdes-blwc = <1>, <1>, <0>; + amd,serdes-cdr-rate = <2>, <2>, <7>; + amd,serdes-pq-skew = <10>, <10>, <30>; + amd,serdes-tx-amp = <15>, <15>, <10>; + amd,serdes-dfe-tap-config = <3>, <3>, <1>; + amd,serdes-dfe-tap-enable = <0>, <0>, <127>; }; |