diff options
Diffstat (limited to 'Documentation/devicetree/bindings/media/i2c')
15 files changed, 908 insertions, 343 deletions
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt deleted file mode 100644 index b3e688b77a38..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/adv7604.txt +++ /dev/null @@ -1,88 +0,0 @@ -* Analog Devices ADV7604/11/12 video decoder with HDMI receiver - -The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated -HDMI receiver. The ADV7604 has four multiplexed HDMI inputs and one analog -input, and the ADV7611 has one HDMI input and no analog input. The 7612 is -similar to the 7611 but has 2 HDMI inputs. - -These device tree bindings support the ADV7611/12 only at the moment. - -Required Properties: - - - compatible: Must contain one of the following - - "adi,adv7611" for the ADV7611 - - "adi,adv7612" for the ADV7612 - - - reg: I2C slave addresses - The ADV76xx has up to thirteen 256-byte maps that can be accessed via the - main I2C ports. Each map has it own I2C address and acts as a standard - slave device on the I2C bus. The main address is mandatory, others are - optional and revert to defaults if not specified. - - - hpd-gpios: References to the GPIOs that control the HDMI hot-plug - detection pins, one per HDMI input. The active flag indicates the GPIO - level that enables hot-plug detection. - -The device node must contain one 'port' child node per device input and output -port, in accordance with the video interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes -are numbered as follows. - - Port ADV7611 ADV7612 ------------------------------------------------------------- - HDMI 0 0, 1 - Digital output 1 2 - -The digital output port node must contain at least one endpoint. - -Optional Properties: - - - reset-gpios: Reference to the GPIO connected to the device's reset pin. - - default-input: Select which input is selected after reset. - - reg-names : Names of maps with programmable addresses. - It can contain any map needing a non-default address. - Possible maps names are : - "main", "avlink", "cec", "infoframe", "esdp", "dpp", "afe", - "rep", "edid", "hdmi", "test", "cp", "vdp" - -Optional Endpoint Properties: - - The following three properties are defined in video-interfaces.txt and are - valid for source endpoints only. - - - hsync-active: Horizontal synchronization polarity. Defaults to active low. - - vsync-active: Vertical synchronization polarity. Defaults to active low. - - pclk-sample: Pixel clock polarity. Defaults to output on the falling edge. - - If none of hsync-active, vsync-active and pclk-sample is specified the - endpoint will use embedded BT.656 synchronization. - -Example: - - hdmi_receiver@4c { - compatible = "adi,adv7611"; - /* - * The edid page will be accessible @ 0x66 on the I2C bus. All - * other maps will retain their default addresses. - */ - reg = <0x4c>, <0x66>; - reg-names = "main", "edid"; - - reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; - hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; - - #address-cells = <1>; - #size-cells = <0>; - - default-input = <0>; - - port@0 { - reg = <0>; - }; - port@1 { - reg = <1>; - hdmi_in: endpoint { - remote-endpoint = <&ccdc_in>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.yaml b/Documentation/devicetree/bindings/media/i2c/adv7604.yaml new file mode 100644 index 000000000000..407baddfaa1d --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.yaml @@ -0,0 +1,178 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/adv7604.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADV7604/11/12 video decoder with HDMI receiver + +maintainers: + - Hans Verkuil <hverkuil-cisco@xs4all.nl> + +description: + The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated + HDMI receiver. The ADV7604 has four multiplexed HDMI inputs and one analog + input, and the ADV7611 has one HDMI input and no analog input. The 7612 is + similar to the 7611 but has 2 HDMI inputs. + + These device tree bindings support the ADV7611/12 only at the moment. + +properties: + compatible: + items: + - enum: + - adi,adv7611 + - adi,adv7612 + + reg: + minItems: 1 + maxItems: 13 + + reg-names: + minItems: 1 + maxItems: 13 + items: + - const: main + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + hpd-gpios: + minItems: 1 + description: + References to the GPIOs that control the HDMI hot-plug detection pins, + one per HDMI input. The active flag indicates the GPIO level that + enables hot-plug detection. + + default-input: + maxItems: 1 + description: + Select which input is selected after reset. + + ports: + type: object + description: + A node containing input and output port nodes with endpoint definitions + as documented in + Documentation/devicetree/bindings/media/video-interfaces.txt + +required: + - compatible + - reg + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + const: adi,adv7611 + then: + properties: + ports: + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + port@0: + type: object + description: Input port + port@1: + type: object + description: Output port + + required: + - port@1 + + additionalProperties: false + + required: + - ports + + - if: + properties: + compatible: + contains: + const: adi,adv7612 + then: + properties: + ports: + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + port@2: + type: object + description: Output port + + patternProperties: + "^port@[0-1]$": + type: object + description: Input port + + required: + - port@2 + + additionalProperties: false + + required: + - ports + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + hdmi_receiver@4c { + compatible = "adi,adv7611"; + /* + * The edid page will be accessible @ 0x66 on the I2C bus. All + * other maps will retain their default addresses. + */ + reg = <0x4c>, <0x66>; + reg-names = "main", "edid"; + + reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; + hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; + default-input = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + }; + + port@1 { + reg = <1>; + hdmi_in: endpoint { + remote-endpoint = <&ccdc_in>; + }; + }; + }; + + + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt deleted file mode 100644 index bd896e9f67d1..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt +++ /dev/null @@ -1,46 +0,0 @@ -* Aptina MT9V111 CMOS sensor ----------------------------- - -The Aptina MT9V111 is a 1/4-Inch VGA-format digital image sensor with a core -based on Aptina MT9V011 sensor and an integrated Image Flow Processor (IFP). - -The sensor has an active pixel array of 640x480 pixels and can output a number -of image resolution and formats controllable through a simple two-wires -interface. - -Required properties: --------------------- - -- compatible: shall be "aptina,mt9v111". -- clocks: reference to the system clock input provider. - -Optional properties: --------------------- - -- enable-gpios: output enable signal, pin name "OE#". Active low. -- standby-gpios: low power state control signal, pin name "STANDBY". - Active high. -- reset-gpios: chip reset signal, pin name "RESET#". Active low. - -The device node must contain one 'port' child node with one 'endpoint' child -sub-node for its digital output video port, in accordance with the video -interface bindings defined in: -Documentation/devicetree/bindings/media/video-interfaces.txt - -Example: --------- - - &i2c1 { - camera@48 { - compatible = "aptina,mt9v111"; - reg = <0x48>; - - clocks = <&camera_clk>; - - port { - mt9v111_out: endpoint { - remote-endpoint = <&ceu_in>; - }; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.yaml b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.yaml new file mode 100644 index 000000000000..ff9546e95d05 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/aptina,mt9v111.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Aptina MT9V111 CMOS sensor + +maintainers: + - Jacopo Mondi <jacopo@jmondi.org> + +description: | + The Aptina MT9V111 is a 1/4-Inch VGA-format digital image sensor with a core + based on Aptina MT9V011 sensor and an integrated Image Flow Processor (IFP). + + The sensor has an active pixel array of 640x480 pixels and can output a number + of image resolutions and formats controllable through a simple two-wires + interface. + +properties: + compatible: + const: aptina,mt9v111 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + enable-gpios: + description: Enable signal, pin name "OE#". Active low. + maxItems: 1 + + standby-gpios: + description: | + Low power state control signal, pin name "STANDBY". Active high. + maxItems: 1 + + reset-gpios: + description: Chip reset signal, pin name "RESET#". Active low. + maxItems: 1 + + port: + type: object + description: | + Output video port. See ../video-interfaces.txt. + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + camera@48 { + compatible = "aptina,mt9v111"; + reg = <0x48>; + clocks = <&camera_clk>; + + port { + mt9v111_out: endpoint { + remote-endpoint = <&ceu_in>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml index 9ea827092fdd..68ee8c7d9e79 100644 --- a/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml +++ b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml @@ -40,7 +40,6 @@ properties: poc-supply: description: Regulator providing Power over Coax to the cameras - maxItems: 1 enable-gpios: description: GPIO connected to the \#PWDN pin with inverted polarity diff --git a/Documentation/devicetree/bindings/media/i2c/mipi-ccs.yaml b/Documentation/devicetree/bindings/media/i2c/mipi-ccs.yaml new file mode 100644 index 000000000000..bb3528315f20 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/mipi-ccs.yaml @@ -0,0 +1,133 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2014--2020 Intel Corporation +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/mipi-ccs.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MIPI CCS, SMIA++ and SMIA compliant camera sensors + +maintainers: + - Sakari Ailus <sakari.ailus@linux.intel.com> + +description: + + CCS (Camera Command Set) is a raw Bayer camera sensor standard defined by the + MIPI Alliance; see + <URL:https://www.mipi.org/specifications/camera-command-set>. + + SMIA (Standard Mobile Imaging Architecture) is an image sensor standard + defined jointly by Nokia and ST. SMIA++, defined by Nokia, is an extension of + that. + + More detailed documentation can be found in + Documentation/devicetree/bindings/media/video-interfaces.txt . + +properties: + compatible: + oneOf: + - items: + - const: mipi-ccs-1.1 + - const: mipi-ccs + - items: + - const: mipi-ccs-1.0 + - const: mipi-ccs + - const: nokia,smia + + reg: + maxItems: 1 + + vana-supply: + description: Analogue voltage supply (VANA), sensor dependent. + + vcore-supply: + description: Core voltage supply (VCore), sensor dependent. + + vio-supply: + description: I/O voltage supply (VIO), sensor dependent. + + clocks: + description: External clock to the sensor. + maxItems: 1 + + clock-frequency: + description: Frequency of the external clock to the sensor in Hz. + + reset-gpios: + description: Reset GPIO. Also commonly called XSHUTDOWN in hardware + documentation. + maxItems: 1 + + flash-leds: + description: Flash LED phandles. See ../video-interfaces.txt for details. + + lens-focus: + description: Lens focus controller phandles. See ../video-interfaces.txt + for details. + + rotation: + description: Rotation of the sensor. See ../video-interfaces.txt for + details. + enum: [ 0, 180 ] + + port: + type: object + properties: + endpoint: + type: object + properties: + link-frequencies: + $ref: /schemas/types.yaml#/definitions/uint64-array + description: List of allowed data link frequencies. + data-lanes: + minItems: 1 + maxItems: 8 + bus-type: + description: The type of the data bus. + oneOf: + - const: 1 # CSI-2 C-PHY + - const: 3 # CCP2 + - const: 4 # CSI-2 D-PHY + + required: + - link-frequencies + - data-lanes + - bus-type + +required: + - compatible + - reg + - clock-frequency + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c2 { + #address-cells = <1>; + #size-cells = <0>; + + clock-frequency = <400000>; + + camera-sensor@10 { + compatible = "mipi-ccs-1.0", "mipi-ccs"; + reg = <0x10>; + reset-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>; + vana-supply = <&vaux3>; + clocks = <&omap3_isp 0>; + clock-frequency = <9600000>; + port { + ccs_ep: endpoint { + data-lanes = <1 2>; + remote-endpoint = <&csi2a_ep>; + link-frequencies = /bits/ 64 <199200000 210000000 + 499200000>; + bus-type = <4>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt deleted file mode 100644 index 10ece8108081..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt +++ /dev/null @@ -1,66 +0,0 @@ -SMIA/SMIA++ sensor - -SMIA (Standard Mobile Imaging Architecture) is an image sensor standard -defined jointly by Nokia and ST. SMIA++, defined by Nokia, is an extension -of that. These definitions are valid for both types of sensors. - -More detailed documentation can be found in -Documentation/devicetree/bindings/media/video-interfaces.txt . - -The device node should contain a "port" node which may contain one or more -endpoint nodes, in accordance with video interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt . - -Mandatory properties --------------------- - -- compatible: "nokia,smia" -- reg: I2C address (0x10, or an alternative address) -- vana-supply: Analogue voltage supply (VANA), typically 2,8 volts (sensor - dependent). -- clocks: External clock to the sensor -- clock-frequency: Frequency of the external clock to the sensor -- link-frequencies: List of allowed data link frequencies. An array of - 64-bit elements. - - -Optional properties -------------------- - -- reset-gpios: XSHUTDOWN GPIO -- flash-leds: See ../video-interfaces.txt -- lens-focus: See ../video-interfaces.txt -- rotation: Integer property; valid values are 0 (sensor mounted upright) - and 180 (sensor mounted upside down). See - ../video-interfaces.txt . - - -Endpoint node mandatory properties ----------------------------------- - -- data-lanes: <1..n> - - -Example -------- - -&i2c2 { - clock-frequency = <400000>; - - camera-sensor@10 { - compatible = "nokia,smia"; - reg = <0x10>; - reset-gpios = <&gpio3 20 0>; - vana-supply = <&vaux3>; - clocks = <&omap3_isp 0>; - clock-frequency = <9600000>; - nokia,nvm-size = <512>; /* 8 * 64 */ - link-frequencies = /bits/ 64 <199200000 210000000 499200000>; - port { - smiapp_ep: endpoint { - data-lanes = <1 2>; - remote-endpoint = <&csi2a_ep>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov2680.txt b/Documentation/devicetree/bindings/media/i2c/ov2680.txt deleted file mode 100644 index 11e925ed9dad..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/ov2680.txt +++ /dev/null @@ -1,46 +0,0 @@ -* Omnivision OV2680 MIPI CSI-2 sensor - -Required Properties: -- compatible: should be "ovti,ov2680". -- clocks: reference to the xvclk input clock. -- clock-names: should be "xvclk". -- DOVDD-supply: Digital I/O voltage supply. -- DVDD-supply: Digital core voltage supply. -- AVDD-supply: Analog voltage supply. - -Optional Properties: -- reset-gpios: reference to the GPIO connected to the powerdown/reset pin, - if any. This is an active low signal to the OV2680. - -The device node must contain one 'port' child node for its digital output -video port, and this port must have a single endpoint in accordance with - the video interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt. - -Endpoint node required properties for CSI-2 connection are: -- remote-endpoint: a phandle to the bus receiver's endpoint node. -- clock-lanes: should be set to <0> (clock lane on hardware lane 0). -- data-lanes: should be set to <1> (one CSI-2 lane supported). - -Example: - -&i2c2 { - ov2680: camera-sensor@36 { - compatible = "ovti,ov2680"; - reg = <0x36>; - clocks = <&osc>; - clock-names = "xvclk"; - reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; - DOVDD-supply = <&sw2_reg>; - DVDD-supply = <&sw2_reg>; - AVDD-supply = <®_peri_3p15v>; - - port { - ov2680_to_mipi: endpoint { - remote-endpoint = <&mipi_from_sensor>; - clock-lanes = <0>; - data-lanes = <1>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov772x.txt b/Documentation/devicetree/bindings/media/i2c/ov772x.txt deleted file mode 100644 index 0b3ede5b8e6a..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/ov772x.txt +++ /dev/null @@ -1,40 +0,0 @@ -* Omnivision OV7720/OV7725 CMOS sensor - -The Omnivision OV7720/OV7725 sensor supports multiple resolutions output, -such as VGA, QVGA, and any size scaling down from CIF to 40x30. It also can -support the YUV422, RGB565/555/444, GRB422 or raw RGB output formats. - -Required Properties: -- compatible: shall be one of - "ovti,ov7720" - "ovti,ov7725" -- clocks: reference to the xclk input clock. - -Optional Properties: -- reset-gpios: reference to the GPIO connected to the RSTB pin which is - active low, if any. -- powerdown-gpios: reference to the GPIO connected to the PWDN pin which is - active high, if any. - -The device node shall contain one 'port' child node with one child 'endpoint' -subnode for its digital output video port, in accordance with the video -interface bindings defined in Documentation/devicetree/bindings/media/ -video-interfaces.txt. - -Example: - -&i2c0 { - ov772x: camera@21 { - compatible = "ovti,ov7725"; - reg = <0x21>; - reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_LOW>; - powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_LOW>; - clocks = <&xclk>; - - port { - ov772x_0: endpoint { - remote-endpoint = <&vcap1_in0>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml new file mode 100644 index 000000000000..1c3879ec4122 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml @@ -0,0 +1,159 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov02a10.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV02A10 CMOS Sensor Device Tree Bindings + +maintainers: + - Dongchun Zhu <dongchun.zhu@mediatek.com> + +description: |- + The Omnivision OV02A10 is a low-cost, high performance, 1/5-inch, 2 megapixel + image sensor, which is the latest production derived from Omnivision's CMOS + image sensor technology. Ihis chip supports high frame rate speeds up to 30fps + @ 1600x1200 (UXGA) resolution transferred over a 1-lane MIPI interface. The + sensor output is available via CSI-2 serial data output. + +properties: + compatible: + const: ovti,ov02a10 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + description: + External clock for the sensor. + items: + - const: eclk + + clock-frequency: + description: + Frequency of the eclk clock in Hz. + + dovdd-supply: + description: + Definition of the regulator used as Digital I/O voltage supply. + + avdd-supply: + description: + Definition of the regulator used as Analog voltage supply. + + dvdd-supply: + description: + Definition of the regulator used as Digital core voltage supply. + + powerdown-gpios: + description: + Must be the device tree identifier of the GPIO connected to the + PD_PAD pin. This pin is used to place the OV02A10 into standby mode + or shutdown mode. As the line needs to be high for the powerdown mode + to be active, it should be marked GPIO_ACTIVE_HIGH. + maxItems: 1 + + reset-gpios: + description: + Must be the device tree identifier of the GPIO connected to the + RST_PD pin. If specified, it will be asserted during driver probe. + As the line needs to be low for the reset to be active, it should be + marked GPIO_ACTIVE_LOW. + maxItems: 1 + + rotation: + description: + Definition of the sensor's placement. + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - enum: + - 0 # Sensor Mounted Upright + - 180 # Sensor Mounted Upside Down + default: 0 + + # See ../video-interfaces.txt for details + port: + type: object + additionalProperties: false + description: + Output port node, single endpoint describing the CSI-2 transmitter. + + properties: + endpoint: + type: object + additionalProperties: false + + properties: + link-frequencies: true + ovti,mipi-clock-voltage: + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + description: + Definition of MIPI clock voltage unit. This entry corresponds to + the link speed defined by the 'link-frequencies' property. + If present, the value shall be in the range of 0-4. + default: 4 + remote-endpoint: true + + required: + - link-frequencies + - remote-endpoint + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - clock-names + - clock-frequency + - dovdd-supply + - avdd-supply + - dvdd-supply + - powerdown-gpios + - reset-gpios + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov02a10: camera-sensor@3d { + compatible = "ovti,ov02a10"; + reg = <0x3d>; + + powerdown-gpios = <&pio 107 GPIO_ACTIVE_HIGH>; + reset-gpios = <&pio 109 GPIO_ACTIVE_LOW>; + + clocks = <&ov02a10_clk>; + clock-names = "eclk"; + clock-frequency = <24000000>; + + rotation = <180>; + + dovdd-supply = <&ov02a10_dovdd>; + avdd-supply = <&ov02a10_avdd>; + dvdd-supply = <&ov02a10_dvdd>; + + port { + wcam_out: endpoint { + link-frequencies = /bits/ 64 <390000000>; + ovti,mipi-clock-voltage = <3>; + remote-endpoint = <&mipi_in_wcam>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml new file mode 100644 index 000000000000..43bf749807e1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml @@ -0,0 +1,99 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov2680.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV2680 CMOS Sensor + +maintainers: + - Rui Miguel Silva <rmfrfs@gmail.com> + +description: |- + The OV2680 color sensor is a low voltage, high performance 1/5 inch UXGA (2 + megapixel) CMOS image sensor that provides a single-chip UXGA (1600 x 1200) + camera. It provides full-frame, sub-sampled, or windowed 10-bit images in + various formats via the control of the Serial Camera Control Bus (SCCB) + interface. The OV2680 has an image array capable of operating at up to 30 + frames per second (fps) in UXGA resolution. + +properties: + compatible: + const: ovti,ov2680 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: xvclk + + reset-gpios: + description: + The phandle and specifier for the GPIO that controls sensor reset. + This corresponds to the hardware pin XSHUTDOWN which is physically + active low. + maxItems: 1 + + dovdd-supply: + description: + Definition of the regulator used as interface power supply. + + avdd-supply: + description: + Definition of the regulator used as analog power supply. + + dvdd-supply: + description: + Definition of the regulator used as digital power supply. + + port: + type: object + description: + A node containing an output port node with an endpoint definition + as documented in + Documentation/devicetree/bindings/media/video-interfaces.txt + +required: + - compatible + - reg + - clocks + - clock-names + - dovdd-supply + - avdd-supply + - dvdd-supply + - reset-gpios + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov2680: camera-sensor@36 { + compatible = "ovti,ov2680"; + reg = <0x36>; + clocks = <&osc>; + clock-names = "xvclk"; + reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; + + dovdd-supply = <&sw2_reg>; + dvdd-supply = <&sw2_reg>; + avdd-supply = <®_peri_3p15v>; + + port { + ov2680_to_mipi: endpoint { + remote-endpoint = <&mipi_from_sensor>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov772x.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov772x.yaml new file mode 100644 index 000000000000..6866c2cdac50 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov772x.yaml @@ -0,0 +1,134 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov772x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV7720/OV7725 CMOS sensor + +maintainers: + - Jacopo Mondi <jacopo@jmondi.org> + +description: | + The Omnivision OV7720/OV7725 sensor supports multiple resolutions output, + such as VGA, QVGA, and any size scaling down from CIF to 40x30. It also can + support the YUV422, RGB565/555/444, GRB422 or raw RGB output formats. + +properties: + compatible: + enum: + - ovti,ov7720 + - ovti,ov7725 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + reset-gpios: + description: | + Reference to the GPIO connected to the RSTB pin which is active low. + maxItems: 1 + + powerdown-gpios: + description: | + Reference to the GPIO connected to the PWDN pin which is active high. + maxItems: 1 + + port: + type: object + description: | + Video output port. See ../video-interfaces.txt. + + properties: + endpoint: + type: object + + properties: + bus-type: + enum: [5, 6] + + bus-width: + enum: [8, 10] + default: 10 + + data-shift: + enum: [0, 2] + default: 0 + + hsync-active: + enum: [0, 1] + default: 1 + + vsync-active: + enum: [0, 1] + default: 1 + + pclk-sample: + enum: [0, 1] + default: 1 + + allOf: + - if: + properties: + bus-type: + const: 6 + then: + properties: + hsync-active: false + vsync-active: false + + - if: + properties: + bus-width: + const: 10 + then: + properties: + data-shift: + const: 0 + + required: + - bus-type + + unevaluatedProperties: false + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + ov772x: camera@21 { + compatible = "ovti,ov7725"; + reg = <0x21>; + reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_LOW>; + clocks = <&xclk>; + + port { + ov772x_0: endpoint { + bus-type = <5>; + vsync-active = <0>; + hsync-active = <0>; + pclk-sample = <0>; + bus-width = <8>; + data-shift = <0>; + remote-endpoint = <&vcap1_in0>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx214.txt b/Documentation/devicetree/bindings/media/i2c/sony,imx214.txt deleted file mode 100644 index f11f28a5fda4..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/sony,imx214.txt +++ /dev/null @@ -1,53 +0,0 @@ -* Sony 1/3.06-Inch 13.13Mp CMOS Digital Image Sensor - -The Sony imx214 is a 1/3.06-inch CMOS active pixel digital image sensor with -an active array size of 4224H x 3200V. It is programmable through an I2C -interface. -Image data is sent through MIPI CSI-2, through 2 or 4 lanes at a maximum -throughput of 1.2Gbps/lane. - - -Required Properties: -- compatible: Shall be "sony,imx214". -- reg: I2C bus address of the device. Depending on how the sensor is wired, - it shall be <0x10> or <0x1a>; -- enable-gpios: GPIO descriptor for the enable pin. -- vdddo-supply: Chip digital IO regulator (1.8V). -- vdda-supply: Chip analog regulator (2.7V). -- vddd-supply: Chip digital core regulator (1.12V). -- clocks: Reference to the xclk clock. -- clock-frequency: Frequency of the xclk clock. - -Optional Properties: -- flash-leds: See ../video-interfaces.txt -- lens-focus: See ../video-interfaces.txt - -The imx214 device node shall contain one 'port' child node with -an 'endpoint' subnode. For further reading on port node refer to -Documentation/devicetree/bindings/media/video-interfaces.txt. - -Required Properties on endpoint: -- data-lanes: check ../video-interfaces.txt -- link-frequencies: check ../video-interfaces.txt -- remote-endpoint: check ../video-interfaces.txt - -Example: - - camera-sensor@1a { - compatible = "sony,imx214"; - reg = <0x1a>; - vdddo-supply = <&pm8994_lvs1>; - vddd-supply = <&camera_vddd_1v12>; - vdda-supply = <&pm8994_l17>; - lens-focus = <&ad5820>; - enable-gpios = <&msmgpio 25 GPIO_ACTIVE_HIGH>; - clocks = <&mmcc CAMSS_MCLK0_CLK>; - clock-frequency = <24000000>; - port { - imx214_ep: endpoint { - data-lanes = <1 2 3 4>; - link-frequencies = /bits/ 64 <480000000>; - remote-endpoint = <&csiphy0_ep>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx214.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx214.yaml new file mode 100644 index 000000000000..eb12526a462f --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx214.yaml @@ -0,0 +1,130 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx214.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony 1/3.06-Inch 13.13MP CMOS Digital Image Sensor + +maintainers: + - Ricardo Ribalda <ribalda@kernel.org> + +description: | + The Sony IMX214 is a 1/3.06-inch CMOS active pixel digital image sensor with + an active array size of 4224H x 3200V. It is programmable through an I2C + interface. Image data is sent through MIPI CSI-2, through 2 or 4 lanes at a + maximum throughput of 1.2Gbps/lane. + +properties: + compatible: + const: sony,imx214 + + reg: + enum: + - 0x10 + - 0x1a + + clocks: + description: Reference to the xclk clock. + maxItems: 1 + + clock-frequency: + description: Frequency of the xclk clock in Hz. + + enable-gpios: + description: GPIO descriptor for the enable pin. + maxItems: 1 + + vdddo-supply: + description: Chip digital IO regulator (1.8V). + + vdda-supply: + description: Chip analog regulator (2.7V). + + vddd-supply: + description: Chip digital core regulator (1.12V). + + flash-leds: + description: See ../video-interfaces.txt + + lens-focus: + description: See ../video-interfaces.txt + + port: + type: object + description: | + Video output port. See ../video-interfaces.txt. + + properties: + endpoint: + type: object + + properties: + data-lanes: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: See ../video-interfaces.txt + anyOf: + - items: + - const: 1 + - const: 2 + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + link-frequencies: + $ref: /schemas/types.yaml#/definitions/uint64-array + description: See ../video-interfaces.txt + + required: + - data-lanes + - link-frequencies + + unevaluatedProperties: false + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-frequency + - enable-gpios + - vdddo-supply + - vdda-supply + - vddd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + camera-sensor@1a { + compatible = "sony,imx214"; + reg = <0x1a>; + vdddo-supply = <&pm8994_lvs1>; + vddd-supply = <&camera_vddd_1v12>; + vdda-supply = <&pm8994_l17>; + lens-focus = <&ad5820>; + enable-gpios = <&msmgpio 25 GPIO_ACTIVE_HIGH>; + clocks = <&camera_clk>; + clock-frequency = <24000000>; + + port { + imx214_ep: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <480000000>; + remote-endpoint = <&csiphy0_ep>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx274.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx274.yaml index f697e1a20beb..a66acb20d59b 100644 --- a/Documentation/devicetree/bindings/media/i2c/sony,imx274.yaml +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx274.yaml @@ -33,15 +33,12 @@ properties: vana-supply: description: Sensor 2.8 V analog supply. - maxItems: 1 vdig-supply: description: Sensor 1.8 V digital core supply. - maxItems: 1 vddl-supply: description: Sensor digital IO 1.2 V supply. - maxItems: 1 port: type: object |