1 files changed, 0 insertions, 88 deletions
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
deleted file mode 100644
index b3e688b77a38..000000000000
--- a/Documentation/devicetree/bindings/media/i2c/adv7604.txt
+++ /dev/null
@@ -1,88 +0,0 @@
-* Analog Devices ADV7604/11/12 video decoder with HDMI receiver
-
-The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated
-HDMI receiver. The ADV7604 has four multiplexed HDMI inputs and one analog
-input, and the ADV7611 has one HDMI input and no analog input. The 7612 is
-similar to the 7611 but has 2 HDMI inputs.
-
-These device tree bindings support the ADV7611/12 only at the moment.
-
-Required Properties:
-
-  - compatible: Must contain one of the following
-    - "adi,adv7611" for the ADV7611
-    - "adi,adv7612" for the ADV7612
-
-  - reg: I2C slave addresses
-    The ADV76xx has up to thirteen 256-byte maps that can be accessed via the
-    main I2C ports. Each map has it own I2C address and acts as a standard
-    slave device on the I2C bus. The main address is mandatory, others are
-    optional and revert to defaults if not specified.
-
-  - hpd-gpios: References to the GPIOs that control the HDMI hot-plug
-    detection pins, one per HDMI input. The active flag indicates the GPIO
-    level that enables hot-plug detection.
-
-The device node must contain one 'port' child node per device input and output
-port, in accordance with the video interface bindings defined in
-Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
-are numbered as follows.
-
-  Port			ADV7611    ADV7612
-------------------------------------------------------------
-  HDMI			0             0, 1
-  Digital output	1                2
-
-The digital output port node must contain at least one endpoint.
-
-Optional Properties:
-
-  - reset-gpios: Reference to the GPIO connected to the device's reset pin.
-  - default-input: Select which input is selected after reset.
-  - reg-names : Names of maps with programmable addresses.
-		It can contain any map needing a non-default address.
-		Possible maps names are :
-		  "main", "avlink", "cec", "infoframe", "esdp", "dpp", "afe",
-		  "rep", "edid", "hdmi", "test", "cp", "vdp"
-
-Optional Endpoint Properties:
-
-  The following three properties are defined in video-interfaces.txt and are
-  valid for source endpoints only.
-
-  - hsync-active: Horizontal synchronization polarity. Defaults to active low.
-  - vsync-active: Vertical synchronization polarity. Defaults to active low.
-  - pclk-sample: Pixel clock polarity. Defaults to output on the falling edge.
-
-  If none of hsync-active, vsync-active and pclk-sample is specified the
-  endpoint will use embedded BT.656 synchronization.
-
-Example:
-
-	hdmi_receiver@4c {
-		compatible = "adi,adv7611";
-		/*
-		 * The edid page will be accessible @ 0x66 on the I2C bus. All
-		 * other maps will retain their default addresses.
-		 */
-		reg = <0x4c>, <0x66>;
-		reg-names = "main", "edid";
-
-		reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>;
-		hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		default-input = <0>;
-
-		port@0 {
-			reg = <0>;
-		};
-		port@1 {
-			reg = <1>;
-			hdmi_in: endpoint {
-				remote-endpoint = <&ccdc_in>;
-			};
-		};
-	};