1 files changed, 0 insertions, 86 deletions
diff --git a/Documentation/devicetree/bindings/iio/frequency/adf4350.txt b/Documentation/devicetree/bindings/iio/frequency/adf4350.txt
deleted file mode 100644
index f8c181d81d2d..000000000000
--- a/Documentation/devicetree/bindings/iio/frequency/adf4350.txt
+++ /dev/null
@@ -1,86 +0,0 @@
-Analog Devices ADF4350/ADF4351 device driver
-
-Required properties:
-	- compatible: Should be one of
-		* "adi,adf4350": When using the ADF4350 device
-		* "adi,adf4351": When using the ADF4351 device
-	- reg: SPI chip select numbert for the device
-	- spi-max-frequency: Max SPI frequency to use (< 20000000)
-	- clocks: From common clock binding. Clock is phandle to clock for
-		ADF435x Reference Clock (CLKIN).
-
-Optional properties:
-	- gpios:	 GPIO Lock detect - If set with a valid phandle and GPIO number,
-			pll lock state is tested upon read.
-	- adi,channel-spacing: Channel spacing in Hz (influences MODULUS).
-	- adi,power-up-frequency:	If set in Hz the PLL tunes to
-			the desired frequency on probe.
-	- adi,reference-div-factor: If set the driver skips dynamic calculation
-			and uses this default value instead.
-	- adi,reference-doubler-enable: Enables reference doubler.
-	- adi,reference-div2-enable: Enables reference divider.
-	- adi,phase-detector-polarity-positive-enable: Enables positive phase
-			detector polarity. Default = negative.
-	- adi,lock-detect-precision-6ns-enable: Enables 6ns lock detect precision.
-			Default = 10ns.
-	- adi,lock-detect-function-integer-n-enable: Enables lock detect
-			for integer-N mode. Default = factional-N mode.
-	- adi,charge-pump-current: Charge pump current in mA.
-			Default = 2500mA.
-	- adi,muxout-select: On chip multiplexer output selection.
-			Valid values for the multiplexer output are:
-			0: Three-State Output (default)
-			1: DVDD
-			2: DGND
-			3: R-Counter output
-			4: N-Divider output
-			5: Analog lock detect
-			6: Digital lock detect
-	- adi,low-spur-mode-enable: Enables low spur mode.
-			Default = Low noise mode.
-	- adi,cycle-slip-reduction-enable: Enables cycle slip reduction.
-	- adi,charge-cancellation-enable: Enabled charge pump
-			charge cancellation for integer-N modes.
-	- adi,anti-backlash-3ns-enable: Enables 3ns antibacklash pulse width
-			 for integer-N modes.
-	- adi,band-select-clock-mode-high-enable: Enables faster band
-			selection logic.
-	- adi,12bit-clk-divider: Clock divider value used when
-			adi,12bit-clkdiv-mode != 0
-	- adi,clk-divider-mode:
-			Valid values for the clkdiv mode are:
-			0: Clock divider off (default)
-			1: Fast lock enable
-			2: Phase resync enable
-	- adi,aux-output-enable: Enables auxiliary RF output.
-	- adi,aux-output-fundamental-enable: Selects fundamental VCO output on
-			the auxiliary RF output. Default = Output of RF dividers.
-	- adi,mute-till-lock-enable: Enables Mute-Till-Lock-Detect function.
-	- adi,output-power: Output power selection.
-			Valid values for the power mode are:
-			0: -4dBm (default)
-			1: -1dBm
-			2: +2dBm
-			3: +5dBm
-	- adi,aux-output-power: Auxiliary output power selection.
-			Valid values for the power mode are:
-			0: -4dBm (default)
-			1: -1dBm
-			2: +2dBm
-			3: +5dBm
-
-
-Example:
-		lo_pll0_rx_adf4351: adf4351-rx-lpc@4 {
-			compatible = "adi,adf4351";
-			reg = <4>;
-			spi-max-frequency = <10000000>;
-			clocks = <&clk0_ad9523 9>;
-			clock-names = "clkin";
-			adi,channel-spacing = <10000>;
-			adi,power-up-frequency = <2400000000>;
-			adi,phase-detector-polarity-positive-enable;
-			adi,charge-pump-current = <2500>;
-			adi,output-power = <3>;
-			adi,mute-till-lock-enable;
-		};