diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio/adc')
7 files changed, 346 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt new file mode 100644 index 000000000000..f9e3ff2c656e --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt @@ -0,0 +1,32 @@ +* Amlogic Meson SAR (Successive Approximation Register) A/D converter + +Required properties: +- compatible: depending on the SoC this should be one of: + - "amlogic,meson-gxbb-saradc" for GXBB + - "amlogic,meson-gxl-saradc" for GXL + - "amlogic,meson-gxm-saradc" for GXM + along with the generic "amlogic,meson-saradc" +- reg: the physical base address and length of the registers +- clocks: phandle and clock identifier (see clock-names) +- clock-names: mandatory clocks: + - "clkin" for the reference clock (typically XTAL) + - "core" for the SAR ADC core clock + optional clocks: + - "sana" for the analog clock + - "adc_clk" for the ADC (sampling) clock + - "adc_sel" for the ADC (sampling) clock mux +- vref-supply: the regulator supply for the ADC reference voltage +- #io-channel-cells: must be 1, see ../iio-bindings.txt + +Example: + saradc: adc@8680 { + compatible = "amlogic,meson-gxl-saradc", "amlogic,meson-saradc"; + #io-channel-cells = <1>; + reg = <0x0 0x8680 0x0 0x34>; + clocks = <&xtal>, + <&clkc CLKID_SAR_ADC>, + <&clkc CLKID_SANA>, + <&clkc CLKID_SAR_ADC_CLK>, + <&clkc CLKID_SAR_ADC_SEL>; + clock-names = "clkin", "core", "sana", "adc_clk", "adc_sel"; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/avia-hx711.txt b/Documentation/devicetree/bindings/iio/adc/avia-hx711.txt new file mode 100644 index 000000000000..b3629405f568 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/avia-hx711.txt @@ -0,0 +1,18 @@ +* AVIA HX711 ADC chip for weight cells + Bit-banging driver + +Required properties: + - compatible: Should be "avia,hx711" + - sck-gpios: Definition of the GPIO for the clock + - dout-gpios: Definition of the GPIO for data-out + See Documentation/devicetree/bindings/gpio/gpio.txt + - avdd-supply: Definition of the regulator used as analog supply + +Example: +weight@0 { + compatible = "avia,hx711"; + sck-gpios = <&gpio3 10 GPIO_ACTIVE_HIGH>; + dout-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; + avdd-suppy = <&avdd>; +}; + diff --git a/Documentation/devicetree/bindings/iio/adc/max11100.txt b/Documentation/devicetree/bindings/iio/adc/max11100.txt new file mode 100644 index 000000000000..b7f7177b8aca --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/max11100.txt @@ -0,0 +1,18 @@ +* Maxim max11100 Analog to Digital Converter (ADC) + +Required properties: + - compatible: Should be "maxim,max11100" + - reg: the adc unit address + - vref-supply: phandle to the regulator that provides reference voltage + +Optional properties: + - spi-max-frequency: SPI maximum frequency + +Example: + +max11100: adc@0 { + compatible = "maxim,max11100"; + reg = <0>; + vref-supply = <&adc0_vref>; + spi-max-frequency = <240000>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt new file mode 100644 index 000000000000..53cd146d8096 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt @@ -0,0 +1,149 @@ +Qualcomm's PM8xxx voltage XOADC + +The Qualcomm PM8xxx PMICs contain a HK/XO ADC (Housekeeping/Crystal +oscillator ADC) encompassing PM8018, PM8038, PM8058 and PM8921. + +Required properties: + +- compatible: should be one of: + "qcom,pm8018-adc" + "qcom,pm8038-adc" + "qcom,pm8058-adc" + "qcom,pm8921-adc" + +- reg: should contain the ADC base address in the PMIC, typically + 0x197. + +- xoadc-ref-supply: should reference a regulator that can supply + a reference voltage on demand. The reference voltage may vary + with PMIC variant but is typically something like 2.2 or 1.8V. + +The following required properties are standard for IO channels, see +iio-bindings.txt for more details: + +- #address-cells: should be set to <1> + +- #size-cells: should be set to <0> + +- #io-channel-cells: should be set to <1> + +- interrupts: should refer to the parent PMIC interrupt controller + and reference the proper ADC interrupt. + +Required subnodes: + +The ADC channels are configured as subnodes of the ADC. Since some of +them are used for calibrating the ADC, these nodes are compulsory: + +adc-channel@c { + reg = <0x0c>; +}; + +adc-channel@d { + reg = <0x0d>; +}; + +adc-channel@f { + reg = <0x0f>; +}; + +These three nodes are used for absolute and ratiometric calibration +and only need to have these reg values: they are by hardware definition +1:1 ratio converters that sample 625, 1250 and 0 milliV and create +an interpolation calibration for all other ADCs. + +Optional subnodes: any channels other than channel 0x0c, 0x0d and +0x0f are optional. + +Required channel node properties: + +- reg: should contain the hardware channel number in the range + 0 .. 0x0f (4 bits). The hardware only supports 16 channels. + +Optional channel node properties: + +- qcom,decimation: + Value type: <u32> + Definition: This parameter is used to decrease the ADC sampling rate. + Quicker measurements can be made by reducing the decimation ratio. + Valid values are 512, 1024, 2048, 4096. + If the property is not found, a default value of 512 will be used. + +- qcom,ratiometric: + Value type: <u32> + Definition: Channel calibration type. If this property is specified + VADC will use a special voltage references for channel + calibration. The available references are specified in the + as a u32 value setting (see below) and it is compulsory + to also specify this reference if ratiometric calibration + is selected. + + If the property is not found, the channel will be + calibrated with the 0.625V and 1.25V reference channels, also + known as an absolute calibration. + The reference voltage pairs when using ratiometric calibration: + 0 = XO_IN/XOADC_GND + 1 = PMIC_IN/XOADC_GND + 2 = PMIC_IN/BMS_CSP + 3 (invalid) + 4 = XOADC_GND/XOADC_GND + 5 = XOADC_VREF/XOADC_GND + +Example: + +xoadc: xoadc@197 { + compatible = "qcom,pm8058-adc"; + reg = <0x197>; + interrupt-parent = <&pm8058>; + interrupts = <76 1>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + + vcoin: adc-channel@0 { + reg = <0x00>; + }; + vbat: adc-channel@1 { + reg = <0x01>; + }; + dcin: adc-channel@2 { + reg = <0x02>; + }; + ichg: adc-channel@3 { + reg = <0x03>; + }; + vph_pwr: adc-channel@4 { + reg = <0x04>; + }; + usb_vbus: adc-channel@a { + reg = <0x0a>; + }; + die_temp: adc-channel@b { + reg = <0x0b>; + }; + ref_625mv: adc-channel@c { + reg = <0x0c>; + }; + ref_1250mv: adc-channel@d { + reg = <0x0d>; + }; + ref_325mv: adc-channel@e { + reg = <0x0e>; + }; + ref_muxoff: adc-channel@f { + reg = <0x0f>; + }; +}; + + +/* IIO client node */ +iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&xoadc 0x01>, /* Battery */ + <&xoadc 0x02>, /* DC in (charger) */ + <&xoadc 0x04>, /* VPH the main system voltage */ + <&xoadc 0x0b>, /* Die temperature */ + <&xoadc 0x0c>, /* Reference voltage 1.25V */ + <&xoadc 0x0d>, /* Reference voltage 0.625V */ + <&xoadc 0x0e>; /* Reference voltage 0.325V */ +}; diff --git a/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt new file mode 100644 index 000000000000..f5b0adae6010 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt @@ -0,0 +1,99 @@ +* Renesas RCar GyroADC device driver + +The GyroADC block is a reduced SPI block with up to 8 chipselect lines, +which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs +are sampled by the GyroADC block in a round-robin fashion and the result +presented in the GyroADC registers. + +Required properties: +- compatible: Should be "<soc-specific>", "renesas,rcar-gyroadc". + The <soc-specific> should be one of: + renesas,r8a7791-gyroadc - for the GyroADC block present + in r8a7791 SoC + renesas,r8a7792-gyroadc - for the GyroADC with interrupt + block present in r8a7792 SoC +- reg: Address and length of the register set for the device +- clocks: References to all the clocks specified in the clock-names + property as specified in + Documentation/devicetree/bindings/clock/clock-bindings.txt. +- clock-names: Shall contain "fck" and "if". The "fck" is the GyroADC block + clock, the "if" is the interface clock. +- power-domains: Must contain a reference to the PM domain, if available. +- #address-cells: Should be <1> (setting for the subnodes) for all ADCs + except for "fujitsu,mb88101a". Should be <0> (setting for + only subnode) for "fujitsu,mb88101a". +- #size-cells: Should be <0> (setting for the subnodes) + +Sub-nodes: +You must define subnode(s) which select the connected ADC type and reference +voltage for the GyroADC channels. + +Required properties for subnodes: +- compatible: Should be either of: + "fujitsu,mb88101a" + - Fujitsu MB88101A compatible mode, + 12bit sampling, up to 4 channels can be sampled in + round-robin fashion. One Fujitsu chip supplies four + GyroADC channels with data as it contains four ADCs + on the chip and thus for 4-channel operation, single + MB88101A is required. The Cx chipselect lines of the + MB88101A connect directly to two CHS lines of the + GyroADC, no demuxer is required. The data out line + of each MB88101A connects to a shared input pin of + the GyroADC. + "ti,adcs7476" or "ti,adc121" or "adi,ad7476" + - TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode, + 15bit sampling, up to 8 channels can be sampled in + round-robin fashion. One TI/ADI chip supplies single + ADC channel with data, thus for 8-channel operation, + 8 chips are required. A 3:8 chipselect demuxer is + required to connect the nCS line of the TI/ADI chips + to the GyroADC, while MISO line of each TI/ADI ADC + connects to a shared input pin of the GyroADC. + "maxim,max1162" or "maxim,max11100" + - Maxim MAX1162 / Maxim MAX11100 compatible mode, + 16bit sampling, up to 8 channels can be sampled in + round-robin fashion. One Maxim chip supplies single + ADC channel with data, thus for 8-channel operation, + 8 chips are required. A 3:8 chipselect demuxer is + required to connect the nCS line of the MAX chips + to the GyroADC, while MISO line of each Maxim ADC + connects to a shared input pin of the GyroADC. +- reg: Should be the number of the analog input. Should be present + for all ADCs except "fujitsu,mb88101a". +- vref-supply: Reference to the channel reference voltage regulator. + +Example: + vref_max1162: regulator-vref-max1162 { + compatible = "regulator-fixed"; + + regulator-name = "MAX1162 Vref"; + regulator-min-microvolt = <4096000>; + regulator-max-microvolt = <4096000>; + }; + + adc@e6e54000 { + compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc"; + reg = <0 0xe6e54000 0 64>; + clocks = <&mstp9_clks R8A7791_CLK_GYROADC>, <&clk_65m>; + clock-names = "fck", "if"; + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; + + pinctrl-0 = <&adc_pins>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + reg = <0>; + compatible = "maxim,max1162"; + vref-supply = <&vref_max1162>; + }; + + adc@1 { + reg = <1>; + compatible = "maxim,max1162"; + vref-supply = <&vref_max1162>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt index 49ed82e89870..5dfc88ec24a4 100644 --- a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt @@ -53,6 +53,11 @@ Required properties: - #io-channel-cells = <1>: See the IIO bindings section "IIO consumers" in Documentation/devicetree/bindings/iio/iio-bindings.txt +Optional properties: +- dmas: Phandle to dma channel for this ADC instance. + See ../../dma/dma.txt for details. +- dma-names: Must be "rx" when dmas property is being used. + Example: adc: adc@40012000 { compatible = "st,stm32f4-adc-core"; @@ -77,6 +82,8 @@ Example: interrupt-parent = <&adc>; interrupts = <0>; st,adc-channels = <8>; + dmas = <&dma2 0 0 0x400 0x0>; + dma-names = "rx"; }; ... other adc child nodes follow... diff --git a/Documentation/devicetree/bindings/iio/adc/ti-ads7950.txt b/Documentation/devicetree/bindings/iio/adc/ti-ads7950.txt new file mode 100644 index 000000000000..e77a6f7e1001 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-ads7950.txt @@ -0,0 +1,23 @@ +* Texas Instruments ADS7950 family of A/DC chips + +Required properties: + - compatible: Must be one of "ti,ads7950", "ti,ads7951", "ti,ads7952", + "ti,ads7953", "ti,ads7954", "ti,ads7955", "ti,ads7956", "ti,ads7957", + "ti,ads7958", "ti,ads7959", "ti,ads7960", or "ti,ads7961" + - reg: SPI chip select number for the device + - #io-channel-cells: Must be 1 as per ../iio-bindings.txt + - vref-supply: phandle to a regulator node that supplies the 2.5V or 5V + reference voltage + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: +adc@0 { + compatible = "ti,ads7957"; + reg = <0>; + #io-channel-cells = <1>; + vref-supply = <&refin_supply>; + spi-max-frequency = <10000000>; +}; |