diff options
Diffstat (limited to 'Documentation/devicetree/bindings/clock')
5 files changed, 196 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/clock/clk-palmas-clk32kg-clocks.txt b/Documentation/devicetree/bindings/clock/clk-palmas-clk32kg-clocks.txt new file mode 100644 index 000000000000..4208886d834a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/clk-palmas-clk32kg-clocks.txt @@ -0,0 +1,35 @@ +* Palmas 32KHz clocks * + +Palmas device has two clock output pins for 32KHz, KG and KG_AUDIO. + +This binding uses the common clock binding ./clock-bindings.txt. + +Required properties: +- compatible : "ti,palmas-clk32kg" for clk32kg clock + "ti,palmas-clk32kgaudio" for clk32kgaudio clock +- #clock-cells : shall be set to 0. + +Optional property: +- ti,external-sleep-control: The external enable input pins controlled the + enable/disable of clocks. The external enable input pins ENABLE1, + ENABLE2 and NSLEEP. The valid values for the external pins are: + PALMAS_EXT_CONTROL_PIN_ENABLE1 for ENABLE1 pin + PALMAS_EXT_CONTROL_PIN_ENABLE2 for ENABLE2 pin + PALMAS_EXT_CONTROL_PIN_NSLEEP for NSLEEP pin + Option 0 or missing this property means the clock is enabled/disabled + via register access and these pins do not have any control. + The macros of external control pins for DTS is defined at + dt-bindings/mfd/palmas.h + +Example: + #include <dt-bindings/mfd/palmas.h> + ... + palmas: tps65913@58 { + ... + clk32kg: palmas_clk32k@0 { + compatible = "ti,palmas-clk32kg"; + #clock-cells = <0>; + ti,external-sleep-control = <PALMAS_EXT_CONTROL_PIN_NSLEEP>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/clock/clock-bindings.txt b/Documentation/devicetree/bindings/clock/clock-bindings.txt index f15787817d6b..06fc6d541c89 100644 --- a/Documentation/devicetree/bindings/clock/clock-bindings.txt +++ b/Documentation/devicetree/bindings/clock/clock-bindings.txt @@ -131,3 +131,39 @@ clock signal, and a UART. ("pll" and "pll-switched"). * The UART has its baud clock connected the external oscillator and its register clock connected to the PLL clock (the "pll-switched" signal) + +==Assigned clock parents and rates== + +Some platforms may require initial configuration of default parent clocks +and clock frequencies. Such a configuration can be specified in a device tree +node through assigned-clocks, assigned-clock-parents and assigned-clock-rates +properties. The assigned-clock-parents property should contain a list of parent +clocks in form of phandle and clock specifier pairs, the assigned-clock-parents +property the list of assigned clock frequency values - corresponding to clocks +listed in the assigned-clocks property. + +To skip setting parent or rate of a clock its corresponding entry should be +set to 0, or can be omitted if it is not followed by any non-zero entry. + + uart@a000 { + compatible = "fsl,imx-uart"; + reg = <0xa000 0x1000>; + ... + clocks = <&osc 0>, <&pll 1>; + clock-names = "baud", "register"; + + assigned-clocks = <&clkcon 0>, <&pll 2>; + assigned-clock-parents = <&pll 2>; + assigned-clock-rates = <0>, <460800>; + }; + +In this example the <&pll 2> clock is set as parent of clock <&clkcon 0> and +the <&pll 2> clock is assigned a frequency value of 460800 Hz. + +Configuring a clock's parent and rate through the device node that consumes +the clock can be done only for clocks that have a single user. Specifying +conflicting parent or rate configuration in multiple consumer nodes for +a shared clock is forbidden. + +Configuration of common clocks, which affect multiple consumer devices can +be similarly specified in the clock provider node. diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt new file mode 100644 index 000000000000..0c2bf5eba43e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt @@ -0,0 +1,61 @@ +* Rockchip RK3188/RK3066 Clock and Reset Unit + +The RK3188/RK3066 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3188-cru", "rockchip,rk3188a-cru" or + "rockchip,rk3066a-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3188-cru.h and +dt-bindings/clock/rk3066-cru.h headers and can be used in device tree sources. +Similar macros exist for the reset sources in these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "xin27m" - 27mhz crystal input on rk3066 - optional, + - "ext_hsadc" - external HSADC clock - optional, + - "ext_cif0" - external camera clock - optional, + - "ext_rmii" - external RMII clock - optional, + - "ext_jtag" - externalJTAG clock - optional + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3188-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10124000 { + compatible = "snps,dw-apb-uart"; + reg = <0x10124000 0x400>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt new file mode 100644 index 000000000000..c9fbb76573e1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt @@ -0,0 +1,61 @@ +* Rockchip RK3288 Clock and Reset Unit + +The RK3288 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3288-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3288-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "ext_i2s" - external I2S clock - optional, + - "ext_hsadc" - external HSADC clock - optional, + - "ext_edp_24m" - external display port clock - optional, + - "ext_vip" - external VIP clock - optional, + - "ext_isp" - external ISP clock - optional, + - "ext_jtag" - external JTAG clock - optional + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3188-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10124000 { + compatible = "snps,dw-apb-uart"; + reg = <0x10124000 0x400>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip.txt b/Documentation/devicetree/bindings/clock/rockchip.txt index a891c823ed44..22f6769e5d4a 100644 --- a/Documentation/devicetree/bindings/clock/rockchip.txt +++ b/Documentation/devicetree/bindings/clock/rockchip.txt @@ -6,6 +6,9 @@ This binding uses the common clock binding[1]. == Gate clocks == +These bindings are deprecated! +Please use the soc specific CRU bindings instead. + The gate registers form a continuos block which makes the dt node structure a matter of taste, as either all gates can be put into one gate clock spanning all registers or they can be divided into |