diff options
Diffstat (limited to 'Documentation/ABI/testing')
6 files changed, 121 insertions, 0 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio index 42d360fe66a5..0439c2aaf741 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio +++ b/Documentation/ABI/testing/sysfs-bus-iio @@ -581,6 +581,7 @@ What: /sys/.../iio:deviceX/events/in_voltageY_supply_thresh_rising_en What: /sys/.../iio:deviceX/events/in_voltageY_supply_thresh_falling_en What: /sys/.../iio:deviceX/events/in_voltageY_thresh_rising_en What: /sys/.../iio:deviceX/events/in_voltageY_thresh_falling_en +What: /sys/.../iio:deviceX/events/in_voltageY_thresh_either_en What: /sys/.../iio:deviceX/events/in_tempY_thresh_rising_en What: /sys/.../iio:deviceX/events/in_tempY_thresh_falling_en KernelVersion: 2.6.37 @@ -1459,3 +1460,34 @@ Description: measurements and return the average value as output data. Each value resulted from <type>[_name]_oversampling_ratio measurements is considered as one sample for <type>[_name]_sampling_frequency. + +What: /sys/bus/iio/devices/iio:deviceX/in_concentration_raw +What: /sys/bus/iio/devices/iio:deviceX/in_concentrationX_raw +What: /sys/bus/iio/devices/iio:deviceX/in_concentration_co2_raw +What: /sys/bus/iio/devices/iio:deviceX/in_concentrationX_co2_raw +What: /sys/bus/iio/devices/iio:deviceX/in_concentration_voc_raw +What: /sys/bus/iio/devices/iio:deviceX/in_concentrationX_voc_raw +KernelVersion: 4.3 +Contact: linux-iio@vger.kernel.org +Description: + Raw (unscaled no offset etc.) percentage reading of a substance. + +What: /sys/bus/iio/devices/iio:deviceX/in_resistance_raw +What: /sys/bus/iio/devices/iio:deviceX/in_resistanceX_raw +What: /sys/bus/iio/devices/iio:deviceX/out_resistance_raw +What: /sys/bus/iio/devices/iio:deviceX/out_resistanceX_raw +KernelVersion: 4.3 +Contact: linux-iio@vger.kernel.org +Description: + Raw (unscaled no offset etc.) resistance reading that can be processed + into an ohm value. + +What: /sys/bus/iio/devices/iio:deviceX/heater_enable +KernelVersion: 4.1.0 +Contact: linux-iio@vger.kernel.org +Description: + '1' (enable) or '0' (disable) specifying the enable + of heater function. Same reading values apply + This ABI is especially applicable for humidity sensors + to heatup the device and get rid of any condensation + in some humidity environment diff --git a/Documentation/ABI/testing/sysfs-bus-iio-adc-hi8435 b/Documentation/ABI/testing/sysfs-bus-iio-adc-hi8435 new file mode 100644 index 000000000000..f30b4c424fb6 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-iio-adc-hi8435 @@ -0,0 +1,43 @@ +What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_sensing_mode +Date: August 2015 +KernelVersion: 4.2.0 +Contact: source@cogentembedded.com +Description: + Program sensor type for threshold detector inputs. + Could be either "GND-Open" or "Supply-Open" mode. Y is a + threshold detector input channel. Channels 0..7, 8..15, 16..23 + and 24..31 has common sensor types. + +What: /sys/bus/iio/devices/iio:deviceX/events/in_voltageY_thresh_falling_value +Date: August 2015 +KernelVersion: 4.2.0 +Contact: source@cogentembedded.com +Description: + Channel Y low voltage threshold. If sensor input voltage goes lower then + this value then the threshold falling event is pushed. + Depending on in_voltageY_sensing_mode the low voltage threshold + is separately set for "GND-Open" and "Supply-Open" modes. + Channels 0..31 have common low threshold values, but could have different + sensing_modes. + The low voltage threshold range is between 2..21V. + Hysteresis between low and high thresholds can not be lower then 2 and + can not be odd. + If falling threshold results hysteresis to odd value then rising + threshold is automatically subtracted by one. + +What: /sys/bus/iio/devices/iio:deviceX/events/in_voltageY_thresh_rising_value +Date: August 2015 +KernelVersion: 4.2.0 +Contact: source@cogentembedded.com +Description: + Channel Y high voltage threshold. If sensor input voltage goes higher then + this value then the threshold rising event is pushed. + Depending on in_voltageY_sensing_mode the high voltage threshold + is separately set for "GND-Open" and "Supply-Open" modes. + Channels 0..31 have common high threshold values, but could have different + sensing_modes. + The high voltage threshold range is between 3..22V. + Hysteresis between low and high thresholds can not be lower then 2 and + can not be odd. + If rising threshold results hysteresis to odd value then falling + threshold is automatically appended by one. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-chemical-vz89x b/Documentation/ABI/testing/sysfs-bus-iio-chemical-vz89x new file mode 100644 index 000000000000..c0c1ea924535 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-iio-chemical-vz89x @@ -0,0 +1,7 @@ +What: /sys/bus/iio/devices/iio:deviceX/in_concentration_VOC_short_raw +Date: September 2015 +KernelVersion: 4.3 +Contact: Matt Ranostay <mranostay@gmail.com> +Description: + Get the raw calibration VOC value from the sensor. + This value has little application outside of calibration. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-humidity-hdc100x b/Documentation/ABI/testing/sysfs-bus-iio-humidity-hdc100x new file mode 100644 index 000000000000..b72bb62552cf --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-iio-humidity-hdc100x @@ -0,0 +1,9 @@ +What: /sys/bus/iio/devices/iio:deviceX/out_current_heater_raw +What: /sys/bus/iio/devices/iio:deviceX/out_current_heater_raw_available +KernelVersion: 4.3 +Contact: linux-iio@vger.kernel.org +Description: + Controls the heater device within the humidity sensor to get + rid of excess condensation. + + Valid control values are 0 = OFF, and 1 = ON. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-meas-spec b/Documentation/ABI/testing/sysfs-bus-iio-meas-spec new file mode 100644 index 000000000000..1a6265e92e2f --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-iio-meas-spec @@ -0,0 +1,8 @@ +What: /sys/bus/iio/devices/iio:deviceX/battery_low +KernelVersion: 4.1.0 +Contact: linux-iio@vger.kernel.org +Description: + Reading returns either '1' or '0'. '1' means that the + battery level supplied to sensor is below 2.25V. + This ABI is available for tsys02d, htu21, ms8607 + This ABI is available for htu21, ms8607 diff --git a/Documentation/ABI/testing/sysfs-bus-iio-trigger-sysfs b/Documentation/ABI/testing/sysfs-bus-iio-trigger-sysfs index bbb039237a25..04ac62305018 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-trigger-sysfs +++ b/Documentation/ABI/testing/sysfs-bus-iio-trigger-sysfs @@ -18,3 +18,25 @@ Description: trigger. In order to associate the trigger with an IIO device one should write this name string to /sys/bus/iio/devices/iio:deviceY/trigger/current_trigger. + +What: /sys/bus/iio/devices/iio_sysfs_trigger/add_trigger +KernelVersion: 2.6.39 +Contact: linux-iio@vger.kernel.org +Description: + This attribute is provided by the iio-trig-sysfs stand-alone + driver and it is used to activate the creation of a new trigger. + In order to achieve this, one should write a positive integer + into the associated file, which will serve as the id of the + trigger. If the trigger with the specified id is already present + in the system, an invalid argument message will be returned. + +What: /sys/bus/iio/devices/iio_sysfs_trigger/remove_trigger +KernelVersion: 2.6.39 +Contact: linux-iio@vger.kernel.org +Description: + This attribute is used to unregister and delete a previously + created trigger from the list of available triggers. In order to + achieve this, one should write a positive integer into the + associated file, representing the id of the trigger that needs + to be removed. If the trigger can't be found, an invalid + argument message will be returned to the user. |