diff options
433 files changed, 20755 insertions, 3428 deletions
diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index 973884a1bacf..1dfee20eee74 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -9,6 +9,12 @@ Boards with the Amlogic Meson8 SoC shall have the following properties: Required root node property: compatible: "amlogic,meson8"; +Boards with the Amlogic Meson8b SoC shall have the following properties: + Required root node property: + compatible: "amlogic,meson8b"; + Board compatible values: - - "geniatech,atv1200" - - "minix,neo-x8" + - "geniatech,atv1200" (Meson6) + - "minix,neo-x8" (Meson8) + - "tronfy,mxq" (Meson8b) + - "hardkernel,odroid-c1" (Meson8b) diff --git a/Documentation/devicetree/bindings/arm/apm/scu.txt b/Documentation/devicetree/bindings/arm/apm/scu.txt new file mode 100644 index 000000000000..b45be06625fd --- /dev/null +++ b/Documentation/devicetree/bindings/arm/apm/scu.txt @@ -0,0 +1,17 @@ +APM X-GENE SoC series SCU Registers + +This system clock unit contain various register that control block resets, +clock enable/disables, clock divisors and other deepsleep registers. + +Properties: + - compatible : should contain two values. First value must be: + - "apm,xgene-scu" + second value must be always "syscon". + + - reg : offset and length of the register set. + +Example : + scu: system-clk-controller@17000000 { + compatible = "apm,xgene-scu","syscon"; + reg = <0x0 0x17000000 0x0 0x400>; + }; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt index 430608ec09f0..0d0c1ae81bed 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt @@ -20,6 +20,25 @@ system control is required: - compatible: "brcm,bcm<chip_id>-hif-cpubiuctrl", "syscon" - compatible: "brcm,bcm<chip_id>-hif-continuation", "syscon" +hif-cpubiuctrl node +------------------- +SoCs with Broadcom Brahma15 ARM-based CPUs have a specific Bus Interface Unit +(BIU) block which controls and interfaces the CPU complex to the different +Memory Controller Ports (MCP), one per memory controller (MEMC). This BIU block +offers a feature called Write Pairing which consists in collapsing two adjacent +cache lines into a single (bursted) write transaction towards the memory +controller (MEMC) to maximize write bandwidth. + +Required properties: + + - compatible: must be "brcm,bcm7445-hif-cpubiuctrl", "syscon" + +Optional properties: + + - brcm,write-pairing: + Boolean property, which when present indicates that the chip + supports write-pairing. + example: rdb { #address-cells = <1>; @@ -35,6 +54,7 @@ example: hif_cpubiuctrl: syscon@3e2400 { compatible = "brcm,bcm7445-hif-cpubiuctrl", "syscon"; reg = <0x3e2400 0x5b4>; + brcm,write-pairing; }; hif_continuation: syscon@452000 { @@ -43,8 +63,7 @@ example: }; }; -Lastly, nodes that allow for support of SMP initialization and reboot are -required: +Nodes that allow for support of SMP initialization and reboot are required: smpboot ------- @@ -95,3 +114,142 @@ example: compatible = "brcm,brcmstb-reboot"; syscon = <&sun_top_ctrl 0x304 0x308>; }; + + + +Power management +---------------- + +For power management (particularly, S2/S3/S5 system suspend), the following SoC +components are needed: + += Always-On control block (AON CTRL) + +This hardware provides control registers for the "always-on" (even in low-power +modes) hardware, such as the Power Management State Machine (PMSM). + +Required properties: +- compatible : should contain "brcm,brcmstb-aon-ctrl" +- reg : the register start and length for the AON CTRL block + +Example: + +aon-ctrl@410000 { + compatible = "brcm,brcmstb-aon-ctrl"; + reg = <0x410000 0x400>; +}; + += Memory controllers + +A Broadcom STB SoC typically has a number of independent memory controllers, +each of which may have several associated hardware blocks, which are versioned +independently (control registers, DDR PHYs, etc.). One might consider +describing these controllers as a parent "memory controllers" block, which +contains N sub-nodes (one for each controller in the system), each of which is +associated with a number of hardware register resources (e.g., its PHY). See +the example device tree snippet below. + +== MEMC (MEMory Controller) + +Represents a single memory controller instance. + +Required properties: +- compatible : should contain "brcm,brcmstb-memc" and "simple-bus" + +Should contain subnodes for any of the following relevant hardware resources: + +== DDR PHY control + +Control registers for this memory controller's DDR PHY. + +Required properties: +- compatible : should contain one of these + "brcm,brcmstb-ddr-phy-v225.1" + "brcm,brcmstb-ddr-phy-v240.1" + "brcm,brcmstb-ddr-phy-v240.2" + +- reg : the DDR PHY register range + +== DDR SHIMPHY + +Control registers for this memory controller's DDR SHIMPHY. + +Required properties: +- compatible : should contain "brcm,brcmstb-ddr-shimphy-v1.0" +- reg : the DDR SHIMPHY register range + +== MEMC DDR control + +Sequencer DRAM parameters and control registers. Used for Self-Refresh +Power-Down (SRPD), among other things. + +Required properties: +- compatible : should contain "brcm,brcmstb-memc-ddr" +- reg : the MEMC DDR register range + +Example: + +memory_controllers { + ranges; + compatible = "simple-bus"; + + memc@0 { + compatible = "brcm,brcmstb-memc", "simple-bus"; + ranges; + + ddr-phy@f1106000 { + compatible = "brcm,brcmstb-ddr-phy-v240.1"; + reg = <0xf1106000 0x21c>; + }; + + shimphy@f1108000 { + compatible = "brcm,brcmstb-ddr-shimphy-v1.0"; + reg = <0xf1108000 0xe4>; + }; + + memc-ddr@f1102000 { + reg = <0xf1102000 0x800>; + compatible = "brcm,brcmstb-memc-ddr"; + }; + }; + + memc@1 { + compatible = "brcm,brcmstb-memc", "simple-bus"; + ranges; + + ddr-phy@f1186000 { + compatible = "brcm,brcmstb-ddr-phy-v240.1"; + reg = <0xf1186000 0x21c>; + }; + + shimphy@f1188000 { + compatible = "brcm,brcmstb-ddr-shimphy-v1.0"; + reg = <0xf1188000 0xe4>; + }; + + memc-ddr@f1182000 { + reg = <0xf1182000 0x800>; + compatible = "brcm,brcmstb-memc-ddr"; + }; + }; + + memc@2 { + compatible = "brcm,brcmstb-memc", "simple-bus"; + ranges; + + ddr-phy@f1206000 { + compatible = "brcm,brcmstb-ddr-phy-v240.1"; + reg = <0xf1206000 0x21c>; + }; + + shimphy@f1208000 { + compatible = "brcm,brcmstb-ddr-shimphy-v1.0"; + reg = <0xf1208000 0xe4>; + }; + + memc-ddr@f1202000 { + reg = <0xf1202000 0x800>; + compatible = "brcm,brcmstb-memc-ddr"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,nsp.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,nsp.txt new file mode 100644 index 000000000000..eae53e4556be --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,nsp.txt @@ -0,0 +1,34 @@ +Broadcom Northstar Plus device tree bindings +-------------------------------------------- + +Broadcom Northstar Plus family of SoCs are used for switching control +and management applications as well as residential router/gateway +applications. The SoC features dual core Cortex A9 ARM CPUs, integrating +several peripheral interfaces including multiple Gigabit Ethernet PHYs, +DDR3 memory, PCIE Gen-2, USB 2.0 and USB 3.0, serial and NAND flash, +SATA and several other IO controllers. + +Boards with Northstar Plus SoCs shall have the following properties: + +Required root node property: + +BCM58522 +compatible = "brcm,bcm58522", "brcm,nsp"; + +BCM58525 +compatible = "brcm,bcm58525", "brcm,nsp"; + +BCM58535 +compatible = "brcm,bcm58535", "brcm,nsp"; + +BCM58622 +compatible = "brcm,bcm58622", "brcm,nsp"; + +BCM58623 +compatible = "brcm,bcm58623", "brcm,nsp"; + +BCM58625 +compatible = "brcm,bcm58625", "brcm,nsp"; + +BCM88312 +compatible = "brcm,bcm88312", "brcm,nsp"; diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 91e6e5c478d0..3a07a87fef20 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -195,6 +195,8 @@ nodes to be present and contain the properties described below. "marvell,armada-380-smp" "marvell,armada-390-smp" "marvell,armada-xp-smp" + "mediatek,mt6589-smp" + "mediatek,mt81xx-tz-smp" "qcom,gcc-msm8660" "qcom,kpss-acc-v1" "qcom,kpss-acc-v2" diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index 2a3ba73f0c5c..34c88b0c7ab4 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -128,10 +128,18 @@ Example: reg = <0x0 0x1ee0000 0x0 0x10000>; }; -Freescale LS2085A SoC Device Tree Bindings ------------------------------------------- +Freescale ARMv8 based Layerscape SoC family Device Tree Bindings +---------------------------------------------------------------- -LS2085A ARMv8 based Simulator model +LS2080A ARMv8 based Simulator model Required root node properties: - - compatible = "fsl,ls2085a-simu", "fsl,ls2085a"; + - compatible = "fsl,ls2080a-simu", "fsl,ls2080a"; + +LS2080A ARMv8 based QDS Board +Required root node properties: + - compatible = "fsl,ls2080a-qds", "fsl,ls2080a"; + +LS2080A ARMv8 based RDB Board +Required root node properties: + - compatible = "fsl,ls2080a-rdb", "fsl,ls2080a"; diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt index 764c738bb3ba..6ac7c000af22 100644 --- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt +++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt @@ -20,6 +20,10 @@ HiKey Board Required root node properties: - compatible = "hisilicon,hi6220-hikey", "hisilicon,hi6220"; +HiP05 D02 Board +Required root node properties: + - compatible = "hisilicon,hip05-d02"; + Hisilicon system controller Required properties: diff --git a/Documentation/devicetree/bindings/arm/keystone/keystone.txt b/Documentation/devicetree/bindings/arm/keystone/keystone.txt index 59d7a46f85eb..3090a8a008c0 100644 --- a/Documentation/devicetree/bindings/arm/keystone/keystone.txt +++ b/Documentation/devicetree/bindings/arm/keystone/keystone.txt @@ -9,12 +9,26 @@ Required properties: the form "ti,keystone-*". Generic devices like gic, arch_timers, ns16550 type UART should use the specified compatible for those devices. +SoC families: + +- Keystone 2 generic SoC: + compatible = "ti,keystone" + +SoCs: + +- Keystone 2 Hawking/Kepler + compatible = "ti,k2hk", "ti,keystone" +- Keystone 2 Lamarr + compatible = "ti,k2l", "ti,keystone" +- Keystone 2 Edison + compatible = "ti,k2e", "ti,keystone" + Boards: - Keystone 2 Hawking/Kepler EVM - compatible = "ti,k2hk-evm","ti,keystone" + compatible = "ti,k2hk-evm", "ti,k2hk", "ti,keystone" - Keystone 2 Lamarr EVM - compatible = "ti,k2l-evm","ti,keystone" + compatible = "ti,k2l-evm", "ti, k2l", "ti,keystone" - Keystone 2 Edison EVM - compatible = "ti,k2e-evm","ti,keystone" + compatible = "ti,k2e-evm", "ti,k2e", "ti,keystone" diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt index 4b7c3d9b29bb..97ba45af04fc 100644 --- a/Documentation/devicetree/bindings/arm/pmu.txt +++ b/Documentation/devicetree/bindings/arm/pmu.txt @@ -7,6 +7,7 @@ representation in the device tree should be done as under:- Required properties: - compatible : should be one of + "apm,potenza-pmu" "arm,armv8-pmuv3" "arm.cortex-a57-pmu" "arm.cortex-a53-pmu" diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index af58cd74aeff..8e985dd2f181 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -17,6 +17,10 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "radxa,rock", "rockchip,rk3188"; +- Radxa Rock2 Square board: + Required root node properties: + - compatible = "radxa,rock2-square", "rockchip,rk3288"; + - Firefly Firefly-RK3288 board: Required root node properties: - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; @@ -31,6 +35,13 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "netxeon,r89", "rockchip,rk3288"; +- Google Jaq (Haier Chromebook 11 and more): + Required root node properties: + - compatible = "google,veyron-jaq-rev5", "google,veyron-jaq-rev4", + "google,veyron-jaq-rev3", "google,veyron-jaq-rev2", + "google,veyron-jaq-rev1", "google,veyron-jaq", + "google,veyron", "rockchip,rk3288"; + - Google Jerry (Hisense Chromebook C11 and more): Required root node properties: - compatible = "google,veyron-jerry-rev7", "google,veyron-jerry-rev6", diff --git a/Documentation/devicetree/bindings/arm/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung-boards.txt deleted file mode 100644 index 43589d2466a7..000000000000 --- a/Documentation/devicetree/bindings/arm/samsung-boards.txt +++ /dev/null @@ -1,27 +0,0 @@ -* Samsung's Exynos SoC based boards - -Required root node properties: - - compatible = should be one or more of the following. - - "samsung,monk" - for Exynos3250-based Samsung Simband board. - - "samsung,rinato" - for Exynos3250-based Samsung Gear2 board. - - "samsung,smdkv310" - for Exynos4210-based Samsung SMDKV310 eval board. - - "samsung,trats" - for Exynos4210-based Tizen Reference board. - - "samsung,universal_c210" - for Exynos4210-based Samsung board. - - "samsung,smdk4412", - for Exynos4412-based Samsung SMDK4412 eval board. - - "samsung,trats2" - for Exynos4412-based Tizen Reference board. - - "samsung,smdk5250" - for Exynos5250-based Samsung SMDK5250 eval board. - - "samsung,xyref5260" - for Exynos5260-based Samsung board. - - "samsung,smdk5410" - for Exynos5410-based Samsung SMDK5410 eval board. - - "samsung,smdk5420" - for Exynos5420-based Samsung SMDK5420 eval board. - - "samsung,sd5v1" - for Exynos5440-based Samsung board. - - "samsung,ssdk5440" - for Exynos5440-based Samsung board. - -Optional: - - firmware node, specifying presence and type of secure firmware: - - compatible: only "samsung,secure-firmware" is currently supported - - reg: address of non-secure SYSRAM used for communication with firmware - - firmware@0203F000 { - compatible = "samsung,secure-firmware"; - reg = <0x0203F000 0x1000>; - }; diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt new file mode 100644 index 000000000000..12129c011c8f --- /dev/null +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -0,0 +1,69 @@ +* Samsung's Exynos SoC based boards + +Required root node properties: + - compatible = should be one or more of the following. + - "samsung,monk" - for Exynos3250-based Samsung Simband board. + - "samsung,rinato" - for Exynos3250-based Samsung Gear2 board. + - "samsung,smdkv310" - for Exynos4210-based Samsung SMDKV310 eval board. + - "samsung,trats" - for Exynos4210-based Tizen Reference board. + - "samsung,universal_c210" - for Exynos4210-based Samsung board. + - "samsung,smdk4412", - for Exynos4412-based Samsung SMDK4412 eval board. + - "samsung,trats2" - for Exynos4412-based Tizen Reference board. + - "samsung,smdk5250" - for Exynos5250-based Samsung SMDK5250 eval board. + - "samsung,xyref5260" - for Exynos5260-based Samsung board. + - "samsung,smdk5410" - for Exynos5410-based Samsung SMDK5410 eval board. + - "samsung,smdk5420" - for Exynos5420-based Samsung SMDK5420 eval board. + - "samsung,sd5v1" - for Exynos5440-based Samsung board. + - "samsung,ssdk5440" - for Exynos5440-based Samsung board. + +* Other companies Exynos SoC based + * FriendlyARM + - "friendlyarm,tiny4412" - for Exynos4412-based FriendlyARM + TINY4412 board. + + * Google + - "google,pi" - for Exynos5800-based Google Peach Pi + Rev 10+ board, + also: "google,pi-rev16", "google,pi-rev15", "google,pi-rev14", + "google,pi-rev13", "google,pi-rev12", "google,pi-rev11", + "google,pi-rev10", "google,peach". + + - "google,pit" - for Exynos5420-based Google Peach Pit + Rev 6+ (Exynos5420), + also: "google,pit-rev16", "google,pit-rev15", "google,pit-rev14", + "google,pit-rev13", "google,pit-rev12", "google,pit-rev11", + "google,pit-rev10", "google,pit-rev9", "google,pit-rev8", + "google,pit-rev7", "google,pit-rev6", "google,peach". + + - "google,snow-rev4" - for Exynos5250-based Google Snow board, + also: "google,snow" + - "google,snow-rev5" - for Exynos5250-based Google Snow + Rev 5+ board. + - "google,spring" - for Exynos5250-based Google Spring board. + + * Hardkernel + - "hardkernel,odroid-u3" - for Exynos4412-based Hardkernel Odroid U3. + - "hardkernel,odroid-x" - for Exynos4412-based Hardkernel Odroid X. + - "hardkernel,odroid-x2" - for Exynos4412-based Hardkernel Odroid X2. + - "hardkernel,odroid-xu3" - for Exynos5422-based Hardkernel Odroid XU3. + - "hardkernel,odroid-xu3-lite" - for Exynos5422-based Hardkernel + Odroid XU3 Lite board. + - "hardkernel,odroid-xu4" - for Exynos5422-based Hardkernel Odroid XU4. + + * Insignal + - "insignal,arndale" - for Exynos5250-based Insignal Arndale board. + - "insignal,arndale-octa" - for Exynos5420-based Insignal Arndale + Octa board. + - "insignal,origen" - for Exynos4210-based Insignal Origen board. + - "insignal,origen4412 - for Exynos4412-based Insignal Origen board. + + +Optional nodes: + - firmware node, specifying presence and type of secure firmware: + - compatible: only "samsung,secure-firmware" is currently supported + - reg: address of non-secure SYSRAM used for communication with firmware + + firmware@0203F000 { + compatible = "samsung,secure-firmware"; + reg = <0x0203F000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index 2b9cb62838f2..40bb9007cd0d 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -55,3 +55,7 @@ Boards: compatible = "renesas,lager", "renesas,r8a7790" - Marzen compatible = "renesas,marzen", "renesas,r8a7779" + - Porter (M2-LCDP) + compatible = "renesas,porter", "renesas,r8a7791" + - SILK (RTP0RC7794LCB00011S) + compatible = "renesas,silk", "renesas,r8a7794" diff --git a/Documentation/devicetree/bindings/powerpc/fsl/board.txt b/Documentation/devicetree/bindings/board/fsl-board.txt index cff38bdbc0e4..fb7b03ec2071 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/board.txt +++ b/Documentation/devicetree/bindings/board/fsl-board.txt @@ -21,11 +21,14 @@ Example: This is the memory-mapped registers for on board FPGA. -Required properities: +Required properties: - compatible: should be a board-specific string followed by a string indicating the type of FPGA. Example: - "fsl,<board>-fpga", "fsl,fpga-pixis" + "fsl,<board>-fpga", "fsl,fpga-pixis", or + "fsl,<board>-fpga", "fsl,fpga-qixis" - reg: should contain the address and the length of the FPGA register set. + +Optional properties: - interrupt-parent: should specify phandle for the interrupt controller. - interrupts: should specify event (wakeup) IRQ. @@ -38,6 +41,13 @@ Example (P1022DS): interrupts = <8 8 0 0>; }; +Example (LS2080A-RDB): + + cpld@3,0 { + compatible = "fsl,ls2080ardb-fpga", "fsl,fpga-qixis"; + reg = <0x3 0 0x10000>; + }; + * Freescale BCSR GPIO banks Some BCSR registers act as simple GPIO controllers, each such diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt index 54c23f34f194..152dfaab2575 100644 --- a/Documentation/devicetree/bindings/clock/qcom,gcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.txt @@ -18,10 +18,14 @@ Required properties : - #clock-cells : shall contain 1 - #reset-cells : shall contain 1 +Optional properties : +- #power-domain-cells : shall contain 1 + Example: clock-controller@900000 { compatible = "qcom,gcc-msm8960"; reg = <0x900000 0x4000>; #clock-cells = <1>; #reset-cells = <1>; + #power-domain-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/clock/qcom,mmcc.txt b/Documentation/devicetree/bindings/clock/qcom,mmcc.txt index 29ebf84d25af..34e7614d5074 100644 --- a/Documentation/devicetree/bindings/clock/qcom,mmcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,mmcc.txt @@ -14,10 +14,14 @@ Required properties : - #clock-cells : shall contain 1 - #reset-cells : shall contain 1 +Optional properties : +- #power-domain-cells : shall contain 1 + Example: clock-controller@4000000 { compatible = "qcom,mmcc-msm8960"; reg = <0x4000000 0x1000>; #clock-cells = <1>; #reset-cells = <1>; + #power-domain-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt index 805ddcd79a57..f2455c50533d 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt @@ -1,9 +1,9 @@ -* Freescale MPC512x/MPC8xxx GPIO controller +* Freescale MPC512x/MPC8xxx/Layerscape GPIO controller Required properties: - compatible : Should be "fsl,<soc>-gpio" The following <soc>s are known to be supported: - mpc5121, mpc5125, mpc8349, mpc8572, mpc8610, pq3, qoriq + mpc5121, mpc5125, mpc8349, mpc8572, mpc8610, pq3, qoriq. - reg : Address and length of the register set for the device - interrupts : Should be the port interrupt shared by all 32 pins. - #gpio-cells : Should be two. The first cell is the pin number and diff --git a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt index 610757ce4492..c6d533202d3e 100644 --- a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt +++ b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt @@ -3,10 +3,35 @@ Bindings for a fan connected to the PWM lines Required properties: - compatible : "pwm-fan" - pwms : the PWM that is used to control the PWM fan +- cooling-levels : PWM duty cycle values in a range from 0 to 255 + which correspond to thermal cooling states Example: - pwm-fan { + fan0: pwm-fan { compatible = "pwm-fan"; - status = "okay"; + cooling-min-state = <0>; + cooling-max-state = <3>; + #cooling-cells = <2>; pwms = <&pwm 0 10000 0>; + cooling-levels = <0 102 170 230>; }; + + thermal-zones { + cpu_thermal: cpu-thermal { + thermal-sensors = <&tmu 0>; + polling-delay-passive = <0>; + polling-delay = <0>; + trips { + cpu_alert1: cpu-alert1 { + temperature = <100000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + }; + cooling-maps { + map0 { + trip = <&cpu_alert1>; + cooling-device = <&fan0 0 1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt index 729543c47046..bc620fe32a70 100644 --- a/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt +++ b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt @@ -47,7 +47,7 @@ Required properties: - clocks: Required if the System MMU is needed to gate its clock. - power-domains: Required if the System MMU is needed to gate its power. Please refer to the following document: - Documentation/devicetree/bindings/arm/exynos/power_domain.txt + Documentation/devicetree/bindings/power/pd-samsung.txt Examples: gsc_0: gsc@13e00000 { diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt index a42adda944bf..09b94c97faac 100644 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -22,6 +22,10 @@ Optional properties: - samsung,s2mps11-wrstbi-ground: Indicates that WRSTBI pin of PMIC is pulled down. When the system is suspended it will always go down thus triggerring unwanted buck warm reset (setting buck voltages to default values). +- samsung,s2mps11-acokb-ground: Indicates that ACOKB pin of S2MPS11 PMIC is + connected to the ground so the PMIC must manually set PWRHOLD bit in CTRL1 + register to turn off the power. Usually the ACOKB is pulled up to VBATT so + when PWRHOLD pin goes low, the rising ACOKB will trigger power off. Optional nodes: - clocks: s2mps11, s2mps13, s2mps15 and s5m8767 provide three(AP/CP/BT) buffered 32.768 diff --git a/Documentation/devicetree/bindings/pci/arm,juno-r1-pcie.txt b/Documentation/devicetree/bindings/pci/arm,juno-r1-pcie.txt new file mode 100644 index 000000000000..f7514c170a32 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/arm,juno-r1-pcie.txt @@ -0,0 +1,10 @@ +* ARM Juno R1 PCIe interface + +This PCIe host controller is based on PLDA XpressRICH3-AXI IP +and thus inherits all the common properties defined in plda,xpressrich3-axi.txt +as well as the base properties defined in host-generic-pci.txt. + +Required properties: + - compatible: "arm,juno-r1-pcie" + - dma-coherent: The host controller bridges the AXI transactions into PCIe bus + in a manner that makes the DMA operations to appear coherent to the CPUs. diff --git a/Documentation/devicetree/bindings/pci/plda,xpressrich3-axi.txt b/Documentation/devicetree/bindings/pci/plda,xpressrich3-axi.txt new file mode 100644 index 000000000000..f3f75bfb42bc --- /dev/null +++ b/Documentation/devicetree/bindings/pci/plda,xpressrich3-axi.txt @@ -0,0 +1,12 @@ +* PLDA XpressRICH3-AXI host controller + +The PLDA XpressRICH3-AXI host controller can be configured in a manner that +makes it compliant with the SBSA[1] standard published by ARM Ltd. For those +scenarios, the host-generic-pci.txt bindings apply with the following additions +to the compatible property: + +Required properties: + - compatible: should contain "plda,xpressrich3-axi" to identify the IP used. + + +[1] http://infocenter.arm.com/help/topic/com.arm.doc.den0029a/ diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/power/pd-samsung.txt index e151057d92f0..4e947372a693 100644 --- a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt +++ b/Documentation/devicetree/bindings/power/pd-samsung.txt @@ -43,9 +43,8 @@ Example: mfc_pd: power-domain@10044060 { compatible = "samsung,exynos4210-pd"; reg = <0x10044060 0x20>; - clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MOUT_SW_ACLK333>, - <&clock CLK_MOUT_USER_ACLK333>; - clock-names = "oscclk", "pclk0", "clk0"; + clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MOUT_USER_ACLK333>; + clock-names = "oscclk", "clk0"; #power-domain-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt index c0511142b39c..a6c8afc8385a 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt @@ -17,9 +17,9 @@ Required properties: - reg: Address range of the SCPSYS unit - infracfg: must contain a phandle to the infracfg controller - clock, clock-names: clocks according to the common clock binding. - The clocks needed "mm" and "mfg". These are the - clocks which hardware needs to be enabled before - enabling certain power domains. + The clocks needed "mm", "mfg", "venc" and "venc_lt". + These are the clocks which hardware needs to be enabled + before enabling certain power domains. Example: @@ -30,7 +30,9 @@ Example: infracfg = <&infracfg>; clocks = <&clk26m>, <&topckgen CLK_TOP_MM_SEL>; - clock-names = "mfg", "mm"; + <&topckgen CLK_TOP_VENC_SEL>, + <&topckgen CLK_TOP_VENC_LT_SEL>; + clock-names = "mfg", "mm", "venc", "venc_lt"; }; Example consumer: diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smem.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smem.txt new file mode 100644 index 000000000000..9326cdf6e1b1 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smem.txt @@ -0,0 +1,57 @@ +Qualcomm Shared Memory Manager binding + +This binding describes the Qualcomm Shared Memory Manager, used to share data +between various subsystems and OSes in Qualcomm platforms. + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be: + "qcom,smem" + +- memory-region: + Usage: required + Value type: <prop-encoded-array> + Definition: handle to memory reservation for main SMEM memory region. + +- qcom,rpm-msg-ram: + Usage: required + Value type: <prop-encoded-array> + Definition: handle to RPM message memory resource + +- hwlocks: + Usage: required + Value type: <prop-encoded-array> + Definition: reference to a hwspinlock used to protect allocations from + the shared memory + += EXAMPLE +The following example shows the SMEM setup for MSM8974, with a main SMEM region +at 0xfa00000 and the RPM message ram at 0xfc428000: + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + smem_region: smem@fa00000 { + reg = <0xfa00000 0x200000>; + no-map; + }; + }; + + smem@fa00000 { + compatible = "qcom,smem"; + + memory-region = <&smem_region>; + qcom,rpm-msg-ram = <&rpm_msg_ram>; + + hwlocks = <&tcsr_mutex 3>; + }; + + soc { + rpm_msg_ram: memory@fc428000 { + compatible = "qcom,rpm-msg-ram"; + reg = <0xfc428000 0x4000>; + }; + }; diff --git a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt index 53a3029b7589..64083bc5633c 100644 --- a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt +++ b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt @@ -3,10 +3,12 @@ Mediatek MT6577, MT6572 and MT6589 Timers Required properties: - compatible should contain: - * "mediatek,mt6589-timer" for MT6589 compatible timers * "mediatek,mt6580-timer" for MT6580 compatible timers - * "mediatek,mt6577-timer" for all compatible timers (MT6589, MT6580, - MT6577) + * "mediatek,mt6589-timer" for MT6589 compatible timers + * "mediatek,mt8127-timer" for MT8127 compatible timers + * "mediatek,mt8135-timer" for MT8135 compatible timers + * "mediatek,mt8173-timer" for MT8173 compatible timers + * "mediatek,mt6577-timer" for MT6577 and all above compatible timers - reg: Should contain location and length for timers register. - clocks: Clocks driving the timer hardware. This list should include two clocks. The order is system clock and as second clock the RTC clock. diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 9ff48e0defb4..fb2ad0acedbd 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -1,6 +1,7 @@ synopsys DWC3 CORE -DWC3- USB3 CONTROLLER +DWC3- USB3 CONTROLLER. Complies to the generic USB binding properties + as described in 'usb/generic.txt' Required properties: - compatible: must be "snps,dwc3" diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 8c6cef73e0d7..55df1d444e9f 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -34,6 +34,7 @@ avago Avago Technologies avic Shanghai AVIC Optoelectronics Co., Ltd. axis Axis Communications AB bosch Bosch Sensortec GmbH +boundary Boundary Devices Inc. brcm Broadcom Corporation buffalo Buffalo, Inc. calxeda Calxeda @@ -171,6 +172,7 @@ pericom Pericom Technology Inc. phytec PHYTEC Messtechnik GmbH picochip Picochip Ltd plathome Plat'Home Co., Ltd. +plda PLDA pixcir PIXCIR MICROELECTRONICS Co., Ltd pulsedlight PulsedLight, Inc powervr PowerVR (deprecated, use img) @@ -228,6 +230,7 @@ toradex Toradex AG toshiba Toshiba Corporation toumaz Toumaz tplink TP-LINK Technologies Co., Ltd. +tronfy Tronfy truly Truly Semiconductors Limited upisemi uPI Semiconductor Corp. usi Universal Scientific Industrial Co., Ltd. diff --git a/MAINTAINERS b/MAINTAINERS index 3af5570c2497..a4924c29c6b5 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -789,6 +789,11 @@ S: Maintained F: drivers/net/appletalk/ F: net/appletalk/ +APPLIED MICRO (APM) X-GENE DEVICE TREE SUPPORT +M: Duc Dang <dhdang@apm.com> +S: Supported +F: arch/arm64/boot/dts/apm/ + APPLIED MICRO (APM) X-GENE SOC ETHERNET DRIVER M: Iyappan Subramanian <isubramanian@apm.com> M: Keyur Chudgar <kchudgar@apm.com> @@ -1462,6 +1467,10 @@ F: drivers/*/*s3c2410* F: drivers/*/*/*s3c2410* F: drivers/spi/spi-s3c* F: sound/soc/samsung/* +F: Documentation/arm/Samsung/ +F: Documentation/devicetree/bindings/arm/samsung/ +F: Documentation/devicetree/bindings/sram/samsung-sram.txt +F: Documentation/devicetree/bindings/power/pd-samsung.txt N: exynos ARM/SAMSUNG MOBILE MACHINE SUPPORT diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 19b348ec65e8..30bbc3746130 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -58,7 +58,9 @@ dtb-$(CONFIG_ARCH_AXXIA) += \ axm5516-amarillo.dtb dtb-$(CONFIG_ARCH_BCM2835) += \ bcm2835-rpi-b.dtb \ - bcm2835-rpi-b-plus.dtb + bcm2835-rpi-b-rev2.dtb \ + bcm2835-rpi-b-plus.dtb \ + bcm2835-rpi-a-plus.dtb dtb-$(CONFIG_ARCH_BCM_5301X) += \ bcm4708-asus-rt-ac56u.dtb \ bcm4708-asus-rt-ac68u.dtb \ @@ -72,6 +74,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \ bcm47081-buffalo-wzr-900dhp.dtb \ bcm4709-asus-rt-ac87u.dtb \ bcm4709-buffalo-wxr-1900dhp.dtb \ + bcm4709-netgear-r7000.dtb \ bcm4709-netgear-r8000.dtb dtb-$(CONFIG_ARCH_BCM_63XX) += \ bcm963138dvt.dtb @@ -83,6 +86,8 @@ dtb-$(CONFIG_ARCH_BCM_CYGNUS) += \ dtb-$(CONFIG_ARCH_BCM_MOBILE) += \ bcm28155-ap.dtb \ bcm21664-garnet.dtb +dtb-$(CONFIG_ARCH_BCM_NSP) += \ + bcm958625k.dtb dtb-$(CONFIG_ARCH_BERLIN) += \ berlin2-sony-nsz-gs7.dtb \ berlin2cd-google-chromecast.dtb \ @@ -115,6 +120,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \ exynos5250-arndale.dtb \ exynos5250-smdk5250.dtb \ exynos5250-snow.dtb \ + exynos5250-snow-rev5.dtb \ exynos5250-spring.dtb \ exynos5260-xyref5260.dtb \ exynos5410-smdk5410.dtb \ @@ -123,6 +129,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \ exynos5420-smdk5420.dtb \ exynos5422-odroidxu3.dtb \ exynos5422-odroidxu3-lite.dtb \ + exynos5422-odroidxu4.dtb \ exynos5440-sd5v1.dtb \ exynos5440-ssdk5440.dtb \ exynos5800-peach-pi.dtb @@ -227,6 +234,9 @@ dtb-$(CONFIG_ARCH_MMP) += \ pxa168-aspenite.dtb \ pxa910-dkb.dtb \ mmp2-brownstone.dtb +dtb-$(CONFIG_MACH_MESON8B) += \ + meson8b-mxq.dtb \ + meson8b-odroidc1.dtb dtb-$(CONFIG_ARCH_MOXART) += \ moxart-uc7112lx.dtb dtb-$(CONFIG_SOC_IMX1) += \ @@ -284,6 +294,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-gw551x.dtb \ imx6dl-gw552x.dtb \ imx6dl-hummingboard.dtb \ + imx6dl-nit6xlite.dtb \ imx6dl-nitrogen6x.dtb \ imx6dl-phytec-pbab01.dtb \ imx6dl-rex-basic.dtb \ @@ -313,6 +324,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-gw552x.dtb \ imx6q-hummingboard.dtb \ imx6q-nitrogen6x.dtb \ + imx6q-nitrogen6_max.dtb \ imx6q-phytec-pbab01.dtb \ imx6q-rex-pro.dtb \ imx6q-sabreauto.dtb \ @@ -446,6 +458,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \ am335x-base0033.dtb \ am335x-bone.dtb \ am335x-boneblack.dtb \ + am335x-bonegreen.dtb \ am335x-sl50.dtb \ am335x-evm.dtb \ am335x-evmsk.dtb \ @@ -470,6 +483,7 @@ dtb-$(CONFIG_SOC_AM43XX) += \ am437x-gp-evm.dtb dtb-$(CONFIG_SOC_OMAP5) += \ omap5-cm-t54.dtb \ + omap5-igep0050.dtb \ omap5-sbc-t54.dtb \ omap5-uevm.dtb dtb-$(CONFIG_SOC_DRA7XX) += \ @@ -506,7 +520,10 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \ rk3288-evb-rk808.dtb \ rk3288-firefly-beta.dtb \ rk3288-firefly.dtb \ + rk3288-popmetal.dtb \ rk3288-r89.dtb \ + rk3288-rock2-square.dtb \ + rk3288-veyron-jaq.dtb \ rk3288-veyron-jerry.dtb \ rk3288-veyron-minnie.dtb \ rk3288-veyron-pinky.dtb \ @@ -532,6 +549,7 @@ dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \ r8a7790-lager.dtb \ r8a7791-henninger.dtb \ r8a7791-koelsch.dtb \ + r8a7791-porter.dtb \ r8a7793-gose.dtb \ r8a7794-alt.dtb \ r8a7794-silk.dtb \ @@ -574,7 +592,9 @@ dtb-$(CONFIG_MACH_SUN4I) += \ sun4i-a10-gemei-g9.dtb \ sun4i-a10-hackberry.dtb \ sun4i-a10-hyundai-a7hd.dtb \ + sun4i-a10-inet1.dtb \ sun4i-a10-inet97fv2.dtb \ + sun4i-a10-inet9f-rev03.dtb \ sun4i-a10-itead-iteaduino-plus.dtb \ sun4i-a10-jesurun-q5.dtb \ sun4i-a10-marsboard.dtb \ @@ -582,16 +602,23 @@ dtb-$(CONFIG_MACH_SUN4I) += \ sun4i-a10-mk802.dtb \ sun4i-a10-mk802ii.dtb \ sun4i-a10-olinuxino-lime.dtb \ - sun4i-a10-pcduino.dtb + sun4i-a10-pcduino.dtb \ + sun4i-a10-pcduino2.dtb \ + sun4i-a10-pov-protab2-ips9.dtb dtb-$(CONFIG_MACH_SUN5I) += \ + sun5i-a10s-auxtek-t003.dtb \ sun5i-a10s-auxtek-t004.dtb \ sun5i-a10s-mk802.dtb \ sun5i-a10s-olinuxino-micro.dtb \ sun5i-a10s-r7-tv-dongle.dtb \ + sun5i-a10s-wobo-i5.dtb \ sun5i-a13-hsg-h702.dtb \ + sun5i-a13-inet-98v-rev2.dtb \ sun5i-a13-olinuxino.dtb \ sun5i-a13-olinuxino-micro.dtb \ - sun5i-a13-utoo-p66.dtb + sun5i-a13-q8-tablet.dtb \ + sun5i-a13-utoo-p66.dtb \ + sun5i-r8-chip.dtb dtb-$(CONFIG_MACH_SUN6I) += \ sun6i-a31-app4-evb1.dtb \ sun6i-a31-colombus.dtb \ @@ -599,7 +626,11 @@ dtb-$(CONFIG_MACH_SUN6I) += \ sun6i-a31-i7.dtb \ sun6i-a31-m9.dtb \ sun6i-a31-mele-a1000g-quad.dtb \ - sun6i-a31s-cs908.dtb + sun6i-a31s-cs908.dtb \ + sun6i-a31s-primo81.dtb \ + sun6i-a31s-sina31s.dtb \ + sun6i-a31s-sinovoip-bpi-m2.dtb \ + sun6i-a31s-yones-toptech-bs1078-v2.dtb dtb-$(CONFIG_MACH_SUN7I) += \ sun7i-a20-bananapi.dtb \ sun7i-a20-bananapro.dtb \ @@ -609,6 +640,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \ sun7i-a20-i12-tvbox.dtb \ sun7i-a20-m3.dtb \ sun7i-a20-mk808c.dtb \ + sun7i-a20-olimex-som-evb.dtb \ sun7i-a20-olinuxino-lime.dtb \ sun7i-a20-olinuxino-lime2.dtb \ sun7i-a20-olinuxino-micro.dtb \ @@ -616,14 +648,18 @@ dtb-$(CONFIG_MACH_SUN7I) += \ sun7i-a20-orangepi-mini.dtb \ sun7i-a20-pcduino3.dtb \ sun7i-a20-pcduino3-nano.dtb \ - sun7i-a20-wexler-tab7200.dtb + sun7i-a20-wexler-tab7200.dtb \ + sun7i-a20-wits-pro-a20-dkt.dtb dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-a23-evb.dtb \ + sun8i-a23-gt90h-v4.dtb \ sun8i-a23-ippo-q8h-v5.dtb \ sun8i-a23-ippo-q8h-v1.2.dtb \ + sun8i-a23-q8-tablet.dtb \ sun8i-a33-et-q8-v1.6.dtb \ sun8i-a33-ga10h-v1.1.dtb \ sun8i-a33-ippo-q8h-v1.2.dtb \ + sun8i-a33-q8-tablet.dtb \ sun8i-a33-sinlinx-sina33.dtb dtb-$(CONFIG_MACH_SUN9I) += \ sun9i-a80-optimus.dtb \ @@ -669,7 +705,9 @@ dtb-$(CONFIG_ARCH_UNIPHIER) += \ uniphier-ph1-ld6b-ref.dtb \ uniphier-ph1-pro4-ref.dtb \ uniphier-ph1-sld3-ref.dtb \ - uniphier-ph1-sld8-ref.dtb + uniphier-ph1-sld8-ref.dtb \ + uniphier-proxstream2-gentil.dtb \ + uniphier-proxstream2-vodka.dtb dtb-$(CONFIG_ARCH_VERSATILE) += \ versatile-ab.dtb \ versatile-pb.dtb @@ -699,6 +737,10 @@ dtb-$(CONFIG_MACH_ARMADA_370) += \ armada-370-netgear-rn102.dtb \ armada-370-netgear-rn104.dtb \ armada-370-rd.dtb \ + armada-370-seagate-nas-2bay.dtb \ + armada-370-seagate-nas-4bay.dtb \ + armada-370-seagate-personal-cloud.dtb \ + armada-370-seagate-personal-cloud-2bay.dtb \ armada-370-synology-ds213j.dtb dtb-$(CONFIG_MACH_ARMADA_375) += \ armada-375-db.dtb diff --git a/arch/arm/boot/dts/am335x-base0033.dts b/arch/arm/boot/dts/am335x-base0033.dts index 72a9b3fc4251..58a05f7d0b7c 100644 --- a/arch/arm/boot/dts/am335x-base0033.dts +++ b/arch/arm/boot/dts/am335x-base0033.dts @@ -46,39 +46,39 @@ &am33xx_pinmux { nxp_hdmi_pins: pinmux_nxp_hdmi_pins { pinctrl-single,pins = < - 0x1b0 (PIN_OUTPUT | MUX_MODE3) /* xdma_event_intr0.clkout1 */ - 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0 */ - 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1 */ - 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2 */ - 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3 */ - 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4 */ - 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5 */ - 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6 */ - 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7 */ - 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8 */ - 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9 */ - 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10 */ - 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11 */ - 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12 */ - 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13 */ - 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14 */ - 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15 */ - 0xe0 (PIN_OUTPUT | MUX_MODE0) /* lcd_vsync */ - 0xe4 (PIN_OUTPUT | MUX_MODE0) /* lcd_hsync */ - 0xe8 (PIN_OUTPUT | MUX_MODE0) /* lcd_pclk */ - 0xec (PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en */ + AM33XX_IOPAD(0x9b0, PIN_OUTPUT | MUX_MODE3) /* xdma_event_intr0.clkout1 */ + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0 */ + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1 */ + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2 */ + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3 */ + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4 */ + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5 */ + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6 */ + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7 */ + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8 */ + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9 */ + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10 */ + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11 */ + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12 */ + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13 */ + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14 */ + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15 */ + AM33XX_IOPAD(0x8e0, PIN_OUTPUT | MUX_MODE0) /* lcd_vsync */ + AM33XX_IOPAD(0x8e4, PIN_OUTPUT | MUX_MODE0) /* lcd_hsync */ + AM33XX_IOPAD(0x8e8, PIN_OUTPUT | MUX_MODE0) /* lcd_pclk */ + AM33XX_IOPAD(0x8ec, PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en */ >; }; nxp_hdmi_off_pins: pinmux_nxp_hdmi_off_pins { pinctrl-single,pins = < - 0x1b0 (PIN_OUTPUT | MUX_MODE3) /* xdma_event_intr0.clkout1 */ + AM33XX_IOPAD(0x9b0, PIN_OUTPUT | MUX_MODE3) /* xdma_event_intr0.clkout1 */ >; }; leds_base_pins: pinmux_leds_base_pins { pinctrl-single,pins = < - 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ - 0x88 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn3.gpio2_0 */ + AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ + AM33XX_IOPAD(0x888, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn3.gpio2_0 */ >; }; }; diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi b/arch/arm/boot/dts/am335x-bone-common.dtsi index fec78349c1f3..5d370d54bd30 100644 --- a/arch/arm/boot/dts/am335x-bone-common.dtsi +++ b/arch/arm/boot/dts/am335x-bone-common.dtsi @@ -383,8 +383,7 @@ bus-width = <0x4>; pinctrl-names = "default"; pinctrl-0 = <&mmc1_pins>; - cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; - cd-inverted; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; }; &aes { diff --git a/arch/arm/boot/dts/am335x-bonegreen.dts b/arch/arm/boot/dts/am335x-bonegreen.dts new file mode 100644 index 000000000000..0f65bdaaa583 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bonegreen.dts @@ -0,0 +1,53 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" + +/ { + model = "TI AM335x BeagleBone Green"; + compatible = "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; +}; + +&am33xx_pinmux { + uart2_pins: uart2_pins { + pinctrl-single,pins = < + 0x150 (PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */ + 0x154 (PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */ + >; + }; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + status = "okay"; +}; + +&rtc { + system-power-controller; +}; diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts index 1942a5c8132d..d9d00ab863a2 100644 --- a/arch/arm/boot/dts/am335x-evm.dts +++ b/arch/arm/boot/dts/am335x-evm.dts @@ -737,7 +737,7 @@ bus-width = <4>; pinctrl-names = "default"; pinctrl-0 = <&mmc1_pins>; - cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; }; &mmc3 { diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts index 315bb02c9920..89442e98a837 100644 --- a/arch/arm/boot/dts/am335x-evmsk.dts +++ b/arch/arm/boot/dts/am335x-evmsk.dts @@ -647,7 +647,7 @@ bus-width = <4>; pinctrl-names = "default"; pinctrl-0 = <&mmc1_pins>; - cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; }; &sham { diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi b/arch/arm/boot/dts/am335x-igep0033.dtsi index c0e1135256cc..54f113546ecc 100644 --- a/arch/arm/boot/dts/am335x-igep0033.dtsi +++ b/arch/arm/boot/dts/am335x-igep0033.dtsi @@ -56,41 +56,41 @@ &am33xx_pinmux { i2c0_pins: pinmux_i2c0_pins { pinctrl-single,pins = < - 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ >; }; nandflash_pins: pinmux_nandflash_pins { pinctrl-single,pins = < - 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ - 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ - 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ - 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ - 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ - 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ - 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ - 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ - 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ - 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ - 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ - 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ - 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ - 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ - 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + AM33XX_IOPAD(0x874, PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ + AM33XX_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + AM33XX_IOPAD(0x890, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + AM33XX_IOPAD(0x894, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + AM33XX_IOPAD(0x898, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + AM33XX_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ >; }; uart0_pins: pinmux_uart0_pins { pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ - 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ >; }; leds_pins: pinmux_leds_pins { pinctrl-single,pins = < - 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */ + AM33XX_IOPAD(0x85c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */ >; }; }; diff --git a/arch/arm/boot/dts/am335x-phycore-som.dtsi b/arch/arm/boot/dts/am335x-phycore-som.dtsi index 5dd084f3c81c..2f43e458ea4a 100644 --- a/arch/arm/boot/dts/am335x-phycore-som.dtsi +++ b/arch/arm/boot/dts/am335x-phycore-som.dtsi @@ -29,8 +29,17 @@ reg = <0x80000000 0x10000000>; /* 256 MB */ }; - vbat: fixedregulator@0 { - compatible = "regulator-fixed"; + regulators { + compatible = "simple-bus"; + + vcc5v: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vcc5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; }; }; @@ -233,14 +242,14 @@ #include "tps65910.dtsi" &tps { - vcc1-supply = <&vbat>; - vcc2-supply = <&vbat>; - vcc3-supply = <&vbat>; - vcc4-supply = <&vbat>; - vcc5-supply = <&vbat>; - vcc6-supply = <&vbat>; - vcc7-supply = <&vbat>; - vccio-supply = <&vbat>; + vcc1-supply = <&vcc5v>; + vcc2-supply = <&vcc5v>; + vcc3-supply = <&vcc5v>; + vcc4-supply = <&vcc5v>; + vcc5-supply = <&vcc5v>; + vcc6-supply = <&vcc5v>; + vcc7-supply = <&vcc5v>; + vccio-supply = <&vcc5v>; regulators { vrtc_reg: regulator@0 { @@ -311,13 +320,6 @@ }; }; -&vbat { - regulator-name = "vbat"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-boot-on; -}; - /* SPI Busses */ &am33xx_pinmux { spi0_pins: pinmux_spi0 { diff --git a/arch/arm/boot/dts/am335x-wega.dtsi b/arch/arm/boot/dts/am335x-wega.dtsi index 5e541bd1b45a..2cecb3951e1b 100644 --- a/arch/arm/boot/dts/am335x-wega.dtsi +++ b/arch/arm/boot/dts/am335x-wega.dtsi @@ -11,6 +11,17 @@ model = "Phytec AM335x phyBOARD-WEGA"; compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx"; + regulators { + compatible = "simple-bus"; + + vcc3v3: fixedregulator@1 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + }; }; /* CAN Busses */ @@ -80,7 +91,7 @@ }; &mmc1 { - vmmc-supply = <&vmmc_reg>; + vmmc-supply = <&vcc3v3>; bus-width = <4>; pinctrl-names = "default"; pinctrl-0 = <&mmc1_pins>; diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts index 22038f21f228..d2450ab0a380 100644 --- a/arch/arm/boot/dts/am437x-gp-evm.dts +++ b/arch/arm/boot/dts/am437x-gp-evm.dts @@ -304,6 +304,13 @@ >; }; + dcan0_sleep: dcan0_sleep_pins { + pinctrl-single,pins = < + 0x178 (PIN_INPUT_PULLUP | MUX_MODE7) /* uart1_ctsn.gpio0_12 */ + 0x17c (PIN_INPUT_PULLUP | MUX_MODE7) /* uart1_rtsn.gpio0_13 */ + >; + }; + dcan1_default: dcan1_default_pins { pinctrl-single,pins = < 0x180 (PIN_OUTPUT | MUX_MODE2) /* uart1_rxd.d_can1_tx */ @@ -311,6 +318,13 @@ >; }; + dcan1_sleep: dcan1_sleep_pins { + pinctrl-single,pins = < + 0x180 (PIN_INPUT_PULLUP | MUX_MODE7) /* uart1_rxd.gpio0_14 */ + 0x184 (PIN_INPUT_PULLUP | MUX_MODE7) /* uart1_txd.gpio0_15 */ + >; + }; + vpfe0_pins_default: vpfe0_pins_default { pinctrl-single,pins = < 0x1B0 (PIN_INPUT_PULLUP | MUX_MODE0) /* cam0_hd mode 0*/ @@ -581,8 +595,17 @@ attb-gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; + /* + * 0x264 represents the offset of padconf register of + * gpio3_22 from am43xx_pinmux base. + */ + interrupts-extended = <&gpio3 22 IRQ_TYPE_NONE>, + <&am43xx_pinmux 0x264>; + interrupt-names = "tsc", "wakeup"; + touchscreen-size-x = <1024>; touchscreen-size-y = <600>; + wakeup-source; }; ov2659@30 { @@ -689,7 +712,7 @@ bus-width = <4>; pinctrl-names = "default"; pinctrl-0 = <&mmc1_pins>; - cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; }; /* eMMC sits on mmc2 */ @@ -886,14 +909,16 @@ }; &dcan0 { - pinctrl-names = "default"; + pinctrl-names = "default", "sleep"; pinctrl-0 = <&dcan0_default>; + pinctrl-1 = <&dcan0_sleep>; status = "okay"; }; &dcan1 { - pinctrl-names = "default"; + pinctrl-names = "default", "sleep"; pinctrl-0 = <&dcan1_default>; + pinctrl-1 = <&dcan1_sleep>; status = "okay"; }; diff --git a/arch/arm/boot/dts/am437x-idk-evm.dts b/arch/arm/boot/dts/am437x-idk-evm.dts index af25801418b4..337fb91ee74c 100644 --- a/arch/arm/boot/dts/am437x-idk-evm.dts +++ b/arch/arm/boot/dts/am437x-idk-evm.dts @@ -325,7 +325,7 @@ pinctrl-1 = <&mmc1_pins_sleep>; vmmc-supply = <&v3_3d>; bus-width = <4>; - cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; }; &qspi { diff --git a/arch/arm/boot/dts/am437x-sk-evm.dts b/arch/arm/boot/dts/am437x-sk-evm.dts index 0bb36e9af936..63de2a1b4315 100644 --- a/arch/arm/boot/dts/am437x-sk-evm.dts +++ b/arch/arm/boot/dts/am437x-sk-evm.dts @@ -563,7 +563,7 @@ vmmc-supply = <&dcdc4>; bus-width = <4>; - cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; }; &usb2_phy1 { diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts index 86c2dfbe8875..47954ed990f8 100644 --- a/arch/arm/boot/dts/am43x-epos-evm.dts +++ b/arch/arm/boot/dts/am43x-epos-evm.dts @@ -376,7 +376,7 @@ bus-width = <4>; pinctrl-names = "default"; pinctrl-0 = <&mmc1_pins>; - cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; }; &mac { diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts index d55e3ea89fda..d9ba6b879fc1 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts @@ -35,6 +35,14 @@ regulator-max-microvolt = <3300000>; }; + aic_dvdd: fixedregulator-aic_dvdd { + compatible = "regulator-fixed"; + regulator-name = "aic_dvdd_fixed"; + vin-supply = <&vdd_3v3>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + vtt_fixed: fixedregulator-vtt { /* TPS51200 */ compatible = "regulator-fixed"; @@ -142,6 +150,32 @@ }; }; }; + + sound0: sound@0 { + compatible = "simple-audio-card"; + simple-audio-card,name = "BeagleBoard-X15"; + simple-audio-card,widgets = + "Line", "Line Out", + "Line", "Line In"; + simple-audio-card,routing = + "Line Out", "LLOUT", + "Line Out", "RLOUT", + "MIC2L", "Line In", + "MIC2R", "Line In"; + simple-audio-card,format = "dsp_b"; + simple-audio-card,bitclock-master = <&sound0_master>; + simple-audio-card,frame-master = <&sound0_master>; + simple-audio-card,bitclock-inversion; + + simple-audio-card,cpu { + sound-dai = <&mcasp3>; + }; + + sound0_master: simple-audio-card,codec { + sound-dai = <&tlv320aic3104>; + clocks = <&clkout2_clk>; + }; + }; }; &dra7_pmx_core { @@ -326,6 +360,36 @@ 0x370 (PIN_OUTPUT | MUX_MODE14) /* gpio6_28 LS_OE */ >; }; + + clkout2_pins_default: clkout2_pins_default { + pinctrl-single,pins = < + 0x294 (PIN_OUTPUT_PULLDOWN | MUX_MODE9) /* xref_clk0.clkout2 */ + >; + }; + + clkout2_pins_sleep: clkout2_pins_sleep { + pinctrl-single,pins = < + 0x294 (PIN_INPUT | MUX_MODE15) /* xref_clk0.clkout2 */ + >; + }; + + mcasp3_pins_default: mcasp3_pins_default { + pinctrl-single,pins = < + 0x324 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx.mcasp3_aclkx */ + 0x328 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx.mcasp3_fsx */ + 0x32c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0.mcasp3_axr0 */ + 0x330 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1.mcasp3_axr1 */ + >; + }; + + mcasp3_pins_sleep: mcasp3_pins_sleep { + pinctrl-single,pins = < + 0x324 (PIN_INPUT | MUX_MODE15) + 0x328 (PIN_INPUT | MUX_MODE15) + 0x32c (PIN_INPUT | MUX_MODE15) + 0x330 (PIN_INPUT | MUX_MODE15) + >; + }; }; &i2c1 { @@ -511,6 +575,22 @@ interrupts = <16 IRQ_TYPE_LEVEL_LOW>; #thermal-sensor-cells = <1>; }; + + tlv320aic3104: tlv320aic3104@18 { + #sound-dai-cells = <0>; + compatible = "ti,tlv320aic3104"; + reg = <0x18>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&clkout2_pins_default>; + pinctrl-1 = <&clkout2_pins_sleep>; + status = "okay"; + adc-settle-ms = <40>; + + AVDD-supply = <&vdd_3v3>; + IOVDD-supply = <&vdd_3v3>; + DRVDD-supply = <&vdd_3v3>; + DVDD-supply = <&aic_dvdd>; + }; }; &i2c3 { @@ -586,7 +666,7 @@ vmmc-supply = <&ldo1_reg>; bus-width = <4>; - cd-gpios = <&gpio6 27 0>; /* gpio 219 */ + cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */ }; &mmc2 { @@ -709,3 +789,38 @@ &pcie1 { gpios = <&gpio2 8 GPIO_ACTIVE_LOW>; }; + +&mcasp3 { + #sound-dai-cells = <0>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mcasp3_pins_default>; + pinctrl-1 = <&mcasp3_pins_sleep>; + status = "okay"; + + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + /* 4 serializers */ + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 1 2 0 0 + >; +}; + +&mailbox5 { + status = "okay"; + mbox_ipu1_ipc3x: mbox_ipu1_ipc3x { + status = "okay"; + }; + mbox_dsp1_ipc3x: mbox_dsp1_ipc3x { + status = "okay"; + }; +}; + +&mailbox6 { + status = "okay"; + mbox_ipu2_ipc3x: mbox_ipu2_ipc3x { + status = "okay"; + }; + mbox_dsp2_ipc3x: mbox_dsp2_ipc3x { + status = "okay"; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts index 03542f7b5b94..bb280de511da 100644 --- a/arch/arm/boot/dts/armada-370-db.dts +++ b/arch/arm/boot/dts/armada-370-db.dts @@ -74,7 +74,8 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>; internal-regs { serial@12000 { diff --git a/arch/arm/boot/dts/armada-370-dlink-dns327l.dts b/arch/arm/boot/dts/armada-370-dlink-dns327l.dts index af4dc548c1c0..e2a363b1dd8a 100644 --- a/arch/arm/boot/dts/armada-370-dlink-dns327l.dts +++ b/arch/arm/boot/dts/armada-370-dlink-dns327l.dts @@ -69,7 +69,8 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000 - MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>; pcie-controller { status = "okay"; diff --git a/arch/arm/boot/dts/armada-370-mirabox.dts b/arch/arm/boot/dts/armada-370-mirabox.dts index 0f40d5da28c3..3aa980ad64f0 100644 --- a/arch/arm/boot/dts/armada-370-mirabox.dts +++ b/arch/arm/boot/dts/armada-370-mirabox.dts @@ -61,7 +61,8 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000 - MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>; pcie-controller { status = "okay"; @@ -138,6 +139,10 @@ phy-mode = "rgmii-id"; }; + crypto@90000 { + status = "okay"; + }; + mvsdio@d4000 { pinctrl-0 = <&sdio_pins3>; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/armada-370-netgear-rn102.dts b/arch/arm/boot/dts/armada-370-netgear-rn102.dts index a31207860f34..5555875f44f9 100644 --- a/arch/arm/boot/dts/armada-370-netgear-rn102.dts +++ b/arch/arm/boot/dts/armada-370-netgear-rn102.dts @@ -63,7 +63,8 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000 - MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>; pcie-controller { status = "okay"; @@ -82,6 +83,12 @@ }; internal-regs { + + /* RTC is provided by Intersil ISL12057 I2C RTC chip */ + rtc@10300 { + status = "disabled"; + }; + serial@12000 { status = "okay"; }; diff --git a/arch/arm/boot/dts/armada-370-netgear-rn104.dts b/arch/arm/boot/dts/armada-370-netgear-rn104.dts index 00540f292979..78b563c02f3c 100644 --- a/arch/arm/boot/dts/armada-370-netgear-rn104.dts +++ b/arch/arm/boot/dts/armada-370-netgear-rn104.dts @@ -63,7 +63,8 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000 - MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>; pcie-controller { status = "okay"; @@ -82,6 +83,12 @@ }; internal-regs { + + /* RTC is provided by Intersil ISL12057 I2C RTC chip */ + rtc@10300 { + status = "disabled"; + }; + serial@12000 { status = "okay"; }; diff --git a/arch/arm/boot/dts/armada-370-rd.dts b/arch/arm/boot/dts/armada-370-rd.dts index 19475e68b8e9..fbef730e8d37 100644 --- a/arch/arm/boot/dts/armada-370-rd.dts +++ b/arch/arm/boot/dts/armada-370-rd.dts @@ -74,7 +74,8 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>; pcie-controller { status = "okay"; diff --git a/arch/arm/boot/dts/armada-370-seagate-nas-2bay.dts b/arch/arm/boot/dts/armada-370-seagate-nas-2bay.dts new file mode 100644 index 000000000000..fef0110a8d8a --- /dev/null +++ b/arch/arm/boot/dts/armada-370-seagate-nas-2bay.dts @@ -0,0 +1,36 @@ +/* + * Device Tree file for Seagate NAS 2-Bay (Armada 370 SoC). + * + * Copyright (C) 2015 Seagate + * + * Author: Vincent Donnefort <vdonnefort@gmail.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/* + * Here are some information allowing to identify the device: + * + * Product name : Seagate NAS 2-Bay + * Code name (board/PCB) : Dart 2-Bay + * Model name (case sticker) : SRPD20 + * Material desc (product spec) : STCTxxxxxxx + */ + +/dts-v1/; +#include "armada-370-seagate-nas-xbay.dtsi" + +/ { + model = "Seagate NAS 2-Bay (Dart, SRPD20)"; + compatible = "seagate,dart-2", "marvell,armada370", "marvell,armada-370-xp"; + + gpio-fan { + gpio-fan,speed-map = + < 0 3 + 950 2 + 1400 1 + 1800 0>; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-seagate-nas-4bay.dts b/arch/arm/boot/dts/armada-370-seagate-nas-4bay.dts new file mode 100644 index 000000000000..ae2e1fe50ef6 --- /dev/null +++ b/arch/arm/boot/dts/armada-370-seagate-nas-4bay.dts @@ -0,0 +1,133 @@ +/* + * Device Tree file for Seagate NAS 4-Bay (Armada 370 SoC). + * + * Copyright (C) 2015 Seagate + * + * Author: Vincent Donnefort <vdonnefort@gmail.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/* + * Here are some information allowing to identify the device: + * + * Product name : Seagate NAS 4-Bay + * Code name (board/PCB) : Dart 4-Bay + * Model name (case sticker) : SRPD40 + * Material desc (product spec) : STCUxxxxxxx + */ + +/dts-v1/; +#include "armada-370-seagate-nas-xbay.dtsi" +#include <dt-bindings/leds/leds-ns2.h> + +/ { + model = "Seagate NAS 4-Bay (Dart, SRPD40)"; + compatible = "seagate,dart-4", "marvell,armada370", "marvell,armada-370-xp"; + + soc { + pcie-controller { + /* SATA AHCI controller 88SE9170 */ + pcie@1,0 { + status = "okay"; + }; + }; + + internal-regs { + mdio { + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + + ethernet@74000 { + status = "okay"; + pinctrl-0 = <&ge1_rgmii_pins>; + pinctrl-names = "default"; + phy = <&phy1>; + phy-mode = "rgmii-id"; + }; + + i2c@11000 { + /* I2C GPIO expander (PCA9554A) */ + pca9554: pca9554@21 { + compatible = "nxp,pca9554"; + reg = <0x21>; + #gpio-cells = <2>; + gpio-controller; + }; + }; + }; + }; + + regulators { + regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "SATA2 power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&pca9554 6 GPIO_ACTIVE_HIGH>; + }; + regulator@4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "SATA3 power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&pca9554 7 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-leds { + red-sata2 { + label = "dart:red:sata2"; + gpios = <&pca9554 0 GPIO_ACTIVE_LOW>; + }; + red-sata3 { + label = "dart:red:sata3"; + gpios = <&pca9554 3 GPIO_ACTIVE_LOW>; + }; + }; + + leds-ns2 { + compatible = "lacie,ns2-leds"; + + white-sata2 { + label = "dart:white:sata2"; + cmd-gpio = <&pca9554 1 GPIO_ACTIVE_HIGH>; + slow-gpio = <&pca9554 2 GPIO_ACTIVE_HIGH>; + num-modes = <4>; + modes-map = <NS_V2_LED_SATA 0 0 + NS_V2_LED_OFF 0 1 + NS_V2_LED_ON 1 0 + NS_V2_LED_ON 1 1>; + }; + white-sata3 { + label = "dart:white:sata3"; + cmd-gpio = <&pca9554 4 GPIO_ACTIVE_HIGH>; + slow-gpio = <&pca9554 5 GPIO_ACTIVE_HIGH>; + num-modes = <4>; + modes-map = <NS_V2_LED_SATA 0 0 + NS_V2_LED_OFF 0 1 + NS_V2_LED_ON 1 0 + NS_V2_LED_ON 1 1>; + }; + }; + + gpio-fan { + gpio-fan,speed-map = + < 0 3 + 800 2 + 1050 1 + 1300 0>; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi b/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi new file mode 100644 index 000000000000..3036e25c5992 --- /dev/null +++ b/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi @@ -0,0 +1,231 @@ +/* + * Device Tree common file for the Seagate NAS 2 and 4-bay (Armada 370 SoC). + * + * Copyright (C) 2015 Seagate + * + * Author: Vincent Donnefort <vdonnefort@gmail.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/* + * TODO: add support for the white SATA LEDs associated with HDD 0 and 1. + */ + +#include "armada-370.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x20000000>; /* 512 MB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>; + + pcie-controller { + status = "okay"; + + /* USB 3.0 bridge ASM1042A */ + pcie@2,0 { + status = "okay"; + }; + }; + + internal-regs { + serial@12000 { + status = "okay"; + }; + + sata@a0000 { + nr-ports = <2>; + status = "okay"; + }; + + mdio { + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + }; + + ethernet@70000 { + status = "okay"; + pinctrl-0 = <&ge0_rgmii_pins>; + pinctrl-names = "default"; + phy = <&phy0>; + phy-mode = "rgmii-id"; + }; + + i2c@11000 { + status = "okay"; + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + clock-frequency = <100000>; + + /* RTC - NXP 8563T (second source) */ + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + interrupts = <110>; + }; + /* RTC - MCP7940NT */ + rtc@6f { + compatible = "microchip,mcp7941x"; + reg = <0x6f>; + interrupts = <110>; + }; + }; + + nand@d0000 { + status = "okay"; + num-cs = <1>; + marvell,nand-keep-config; + marvell,nand-enable-arbiter; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x300000>; + }; + partition@300000 { + label = "device-tree"; + reg = <0x300000 0x20000>; + }; + partition@320000 { + label = "linux"; + reg = <0x320000 0x2000000>; + }; + partition@2320000 { + label = "rootfs"; + reg = <0x2320000 0xdce0000>; + }; + }; + }; + + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + + regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "SATA0 power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>; + }; + regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "SATA1 power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-fan { + compatible = "gpio-fan"; + gpios = <&gpio2 0 GPIO_ACTIVE_HIGH + &gpio2 1 GPIO_ACTIVE_HIGH>; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + button@1 { + label = "Power button"; + linux,code = <KEY_POWER>; + gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; + debounce-interval = <100>; + }; + button@2 { + label = "Backup button"; + linux,code = <KEY_OPTION>; + gpios = <&gpio0 31 GPIO_ACTIVE_LOW>; + debounce-interval = <100>; + }; + button@3 { + label = "Reset Button"; + linux,code = <KEY_RESTART>; + gpios = <&gpio1 23 GPIO_ACTIVE_LOW>; + debounce-interval = <100>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + white-power { + label = "dart:white:power"; + gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "timer"; + + }; + red-power { + label = "dart:red:power"; + gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>; + }; + red-sata0 { + label = "dart:red:sata0"; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; + red-sata1 { + label = "dart:red:sata1"; + gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; + }; + }; + + gpio_poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; + }; +}; + +&pinctrl { + pinctrl-0 = <&hdd0_led_sata_pin>, <&hdd1_led_sata_pin>; + pinctrl-names = "default"; + + hdd0_led_sata_pin: hdd0-led-sata-pin { + marvell,pins = "mpp48"; + marvell,function = "sata1"; + }; + hdd0_led_gpio_pin: hdd0-led-gpio-pin { + marvell,pins = "mpp48"; + marvell,function = "gpio"; + }; + hdd1_led_sata_pin: hdd1-led-sata-pin { + marvell,pins = "mpp57"; + marvell,function = "sata0"; + }; + hdd1_led_gpio_pin: hdd1-led-gpio-pin { + marvell,pins = "mpp57"; + marvell,function = "gpio"; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-seagate-personal-cloud-2bay.dts b/arch/arm/boot/dts/armada-370-seagate-personal-cloud-2bay.dts new file mode 100644 index 000000000000..3c91f9821c89 --- /dev/null +++ b/arch/arm/boot/dts/armada-370-seagate-personal-cloud-2bay.dts @@ -0,0 +1,51 @@ +/* + * Device Tree file for Seagate Personal Cloud NAS 2-Bay (Armada 370 SoC). + * + * Copyright (C) 2015 Seagate + * + * Author: Simon Guinot <simon.guinot@sequanux.org> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/* + * Here are some information allowing to identify the device: + * + * Product name : Seagate Personal Cloud 2-Bay + * Code name (board/PCB) : Cumulus Max + * Model name (case sticker) : SRN22C + * Material desc (product spec) : STCSxxxxxxx + */ + +/dts-v1/; +#include "armada-370-seagate-personal-cloud.dtsi" + +/ { + model = "Seagate Personal Cloud 2-Bay (Cumulus, SRN22C)"; + compatible = "seagate,cumulus-max", "marvell,armada370", "marvell,armada-370-xp"; + + soc { + internal-regs { + sata@a0000 { + status = "okay"; + nr-ports = <2>; + }; + }; + }; + + regulators { + regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "SATA1 power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dts b/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dts new file mode 100644 index 000000000000..aad39e97af43 --- /dev/null +++ b/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dts @@ -0,0 +1,37 @@ +/* + * Device Tree file for Seagate Personal Cloud NAS (Armada 370 SoC). + * + * Copyright (C) 2015 Seagate + * + * Author: Simon Guinot <simon.guinot@sequanux.org> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/* + * Here are some information allowing to identify the device: + * + * Product name : Seagate Personal Cloud + * Code name (board/PCB) : Cumulus + * Model name (case sticker) : SRN21C + * Material desc (product spec) : STCRxxxxxxx + */ + +/dts-v1/; +#include "armada-370-seagate-personal-cloud.dtsi" + +/ { + model = "Seagate Personal Cloud (Cumulus, SRN21C)"; + compatible = "seagate,cumulus", "marvell,armada370", "marvell,armada-370-xp"; + + soc { + internal-regs { + sata@a0000 { + status = "okay"; + nr-ports = <1>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dtsi b/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dtsi new file mode 100644 index 000000000000..1aba08e4377c --- /dev/null +++ b/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dtsi @@ -0,0 +1,178 @@ +/* + * Device Tree common file for the Seagate Personal Cloud NAS 1 and 2-Bay + * (Armada 370 SoC). + * + * Copyright (C) 2015 Seagate + * + * Author: Simon Guinot <simon.guinot@sequanux.org> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/* + * TODO: add support for the white SATA LED. + */ + +#include "armada-370.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x20000000>; /* 512 MB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>; + + pcie-controller { + status = "okay"; + + /* USB 3.0 Bridge ASM1042A */ + pcie@1,0 { + status = "okay"; + }; + }; + + internal-regs { + coherency-fabric@20200 { + broken-idle; + }; + + serial@12000 { + status = "okay"; + }; + + mdio { + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + }; + + ethernet@74000 { + status = "okay"; + pinctrl-0 = <&ge1_rgmii_pins>; + pinctrl-names = "default"; + phy = <&phy0>; + phy-mode = "rgmii-id"; + }; + + spi@10600 { + status = "okay"; + pinctrl-0 = <&spi0_pins2>; + pinctrl-names = "default"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + /* MX25L8006E */ + compatible = "mxicy,mx25l8005", "jedec,spi-nor"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <50000000>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x100000>; + }; + }; + }; + + usb@50000 { + status = "okay"; + }; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "USB Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 27 GPIO_ACTIVE_LOW>; + }; + regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "SATA0 power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + button@1 { + label = "Power button"; + linux,code = <KEY_POWER>; + gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; + debounce-interval = <100>; + }; + button@2 { + label = "Reset Button"; + linux,code = <KEY_RESTART>; + gpios = <&gpio1 23 GPIO_ACTIVE_LOW>; + debounce-interval = <100>; + }; + button@3 { + label = "USB VBUS error"; + linux,code = <KEY_UNKNOWN>; + gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; + debounce-interval = <100>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + red-sata0 { + label = "cumulus:red:sata0"; + gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + gpio_poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>; + }; +}; + +&pinctrl { + pinctrl-0 = <&sata_led_pin>; + pinctrl-names = "default"; + + sata_led_pin: sata-led-pin { + marvell,pins = "mpp60"; + marvell,function = "sata0"; + }; + gpio_led_pin: gpio-led-pin { + marvell,pins = "mpp60"; + marvell,function = "gpio"; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-synology-ds213j.dts b/arch/arm/boot/dts/armada-370-synology-ds213j.dts index 4f4924362bf0..836bcc07afc5 100644 --- a/arch/arm/boot/dts/armada-370-synology-ds213j.dts +++ b/arch/arm/boot/dts/armada-370-synology-ds213j.dts @@ -77,7 +77,8 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>; internal-regs { diff --git a/arch/arm/boot/dts/armada-370.dtsi b/arch/arm/boot/dts/armada-370.dtsi index 53a1a5abe147..3b06aa835448 100644 --- a/arch/arm/boot/dts/armada-370.dtsi +++ b/arch/arm/boot/dts/armada-370.dtsi @@ -256,6 +256,11 @@ reg = <0x20800 0x8>; }; + cpu-config@21000 { + compatible = "marvell,armada-370-cpu-config"; + reg = <0x21000 0x8>; + }; + audio_controller: audio-controller@30000 { #sound-dai-cells = <1>; compatible = "marvell,armada370-audio"; @@ -319,6 +324,38 @@ ethernet@74000 { compatible = "marvell,armada-370-neta"; }; + + crypto@90000 { + compatible = "marvell,armada-370-crypto"; + reg = <0x90000 0x10000>; + reg-names = "regs"; + interrupts = <48>; + clocks = <&gateclk 23>; + clock-names = "cesa0"; + marvell,crypto-srams = <&crypto_sram>; + marvell,crypto-sram-size = <0x7e0>; + }; + }; + + crypto_sram: sa-sram { + compatible = "mmio-sram"; + reg = <MBUS_ID(0x09, 0x01) 0 0x800>; + reg-names = "sram"; + clocks = <&gateclk 23>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0x09, 0x01) 0 0x800>; + + /* + * The Armada 370 has an erratum preventing the use of + * the standard workflow for CPU idle support (relying + * on the BootROM code to enter/exit idle state). + * Reserve some amount of the crypto SRAM to put the + * cpuidle workaround. + */ + idle-sram@0 { + reg = <0x0 0x20>; + }; }; }; }; diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/armada-375-db.dts index 5711b97e876c..cded5f0a262d 100644 --- a/arch/arm/boot/dts/armada-375-db.dts +++ b/arch/arm/boot/dts/armada-375-db.dts @@ -65,7 +65,9 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x09) 0 0xf1100000 0x10000 + MBUS_ID(0x09, 0x05) 0 0xf1110000 0x10000>; internal-regs { spi@10600 { diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi index e9a381741ce1..7ccce7529b0c 100644 --- a/arch/arm/boot/dts/armada-375.dtsi +++ b/arch/arm/boot/dts/armada-375.dtsi @@ -513,6 +513,21 @@ }; }; + crypto@90000 { + compatible = "marvell,armada-375-crypto"; + reg = <0x90000 0x10000>; + reg-names = "regs"; + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gateclk 30>, <&gateclk 31>, + <&gateclk 28>, <&gateclk 29>; + clock-names = "cesa0", "cesa1", + "cesaz0", "cesaz1"; + marvell,crypto-srams = <&crypto_sram0>, + <&crypto_sram1>; + marvell,crypto-sram-size = <0x800>; + }; + sata@a0000 { compatible = "marvell,orion-sata"; reg = <0xa0000 0x5000>; @@ -619,5 +634,23 @@ }; }; + + crypto_sram0: sa-sram0 { + compatible = "mmio-sram"; + reg = <MBUS_ID(0x09, 0x09) 0 0x800>; + clocks = <&gateclk 30>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0x09, 0x09) 0 0x800>; + }; + + crypto_sram1: sa-sram1 { + compatible = "mmio-sram"; + reg = <MBUS_ID(0x09, 0x05) 0 0x800>; + clocks = <&gateclk 31>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0x09, 0x05) 0 0x800>; + }; }; }; diff --git a/arch/arm/boot/dts/armada-385-db-ap.dts b/arch/arm/boot/dts/armada-385-db-ap.dts index 4047621b137e..acd5b1519edb 100644 --- a/arch/arm/boot/dts/armada-385-db-ap.dts +++ b/arch/arm/boot/dts/armada-385-db-ap.dts @@ -59,7 +59,9 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000 + MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>; internal-regs { spi1: spi@10680 { diff --git a/arch/arm/boot/dts/armada-385-linksys.dtsi b/arch/arm/boot/dts/armada-385-linksys.dtsi index 74a9c6b54fa7..3710755c6d76 100644 --- a/arch/arm/boot/dts/armada-385-linksys.dtsi +++ b/arch/arm/boot/dts/armada-385-linksys.dtsi @@ -57,7 +57,9 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x09) 0 0xf1100000 0x10000 + MBUS_ID(0x09, 0x05) 0 0xf1110000 0x10000>; internal-regs { diff --git a/arch/arm/boot/dts/armada-388-db.dts b/arch/arm/boot/dts/armada-388-db.dts index 91ac8c118f37..ff47af57f091 100644 --- a/arch/arm/boot/dts/armada-388-db.dts +++ b/arch/arm/boot/dts/armada-388-db.dts @@ -64,7 +64,9 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000 + MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>; internal-regs { spi@10600 { diff --git a/arch/arm/boot/dts/armada-388-gp.dts b/arch/arm/boot/dts/armada-388-gp.dts index 353c92532e7a..a633be3defda 100644 --- a/arch/arm/boot/dts/armada-388-gp.dts +++ b/arch/arm/boot/dts/armada-388-gp.dts @@ -58,7 +58,9 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000 + MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>; internal-regs { spi@10600 { @@ -205,8 +207,21 @@ sdhci@d8000 { pinctrl-names = "default"; pinctrl-0 = <&sdhci_pins>; - cd-gpios = <&expander0 5 GPIO_ACTIVE_LOW>; no-1-8-v; + /* + * A388-GP board v1.5 and higher replace + * hitherto card detection method based on GPIO + * with the one using DAT3 pin. As they are + * incompatible, software-based polling is + * enabled with 'broken-cd' property. For boards + * older than v1.5 it can be replaced with: + * 'cd-gpios = <&expander0 5 GPIO_ACTIVE_LOW>;', + * whereas for the newer ones following can be + * used instead: + * 'dat3-cd;' + * 'cd-inverted;' + */ + broken-cd; wp-inverted; bus-width = <8>; status = "okay"; diff --git a/arch/arm/boot/dts/armada-388-rd.dts b/arch/arm/boot/dts/armada-388-rd.dts index b657b1687e5f..853f9735cc70 100644 --- a/arch/arm/boot/dts/armada-388-rd.dts +++ b/arch/arm/boot/dts/armada-388-rd.dts @@ -65,7 +65,9 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000 + MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>; internal-regs { spi@10600 { diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi index f9f2347d9995..c6a0e9d7f1a9 100644 --- a/arch/arm/boot/dts/armada-38x.dtsi +++ b/arch/arm/boot/dts/armada-38x.dtsi @@ -509,6 +509,21 @@ clocks = <&gateclk 4>; }; + crypto@90000 { + compatible = "marvell,armada-38x-crypto"; + reg = <0x90000 0x10000>; + reg-names = "regs"; + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gateclk 23>, <&gateclk 21>, + <&gateclk 14>, <&gateclk 16>; + clock-names = "cesa0", "cesa1", + "cesaz0", "cesaz1"; + marvell,crypto-srams = <&crypto_sram0>, + <&crypto_sram1>; + marvell,crypto-sram-size = <0x800>; + }; + rtc@a3800 { compatible = "marvell,armada-380-rtc"; reg = <0xa3800 0x20>, <0x184a0 0x0c>; @@ -584,6 +599,24 @@ status = "disabled"; }; }; + + crypto_sram0: sa-sram0 { + compatible = "mmio-sram"; + reg = <MBUS_ID(0x09, 0x19) 0 0x800>; + clocks = <&gateclk 23>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0x09, 0x19) 0 0x800>; + }; + + crypto_sram1: sa-sram1 { + compatible = "mmio-sram"; + reg = <MBUS_ID(0x09, 0x15) 0 0x800>; + clocks = <&gateclk 21>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0x09, 0x15) 0 0x800>; + }; }; clocks { diff --git a/arch/arm/boot/dts/armada-xp-axpwifiap.dts b/arch/arm/boot/dts/armada-xp-axpwifiap.dts index 60bbfe32bb80..23fc670c0427 100644 --- a/arch/arm/boot/dts/armada-xp-axpwifiap.dts +++ b/arch/arm/boot/dts/armada-xp-axpwifiap.dts @@ -69,7 +69,9 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x09) 0 0 0xf8100000 0x10000 + MBUS_ID(0x09, 0x05) 0 0 0xf8110000 0x10000>; pcie-controller { status = "okay"; diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/armada-xp-db.dts index 7dd900f158be..f774101416a5 100644 --- a/arch/arm/boot/dts/armada-xp-db.dts +++ b/arch/arm/boot/dts/armada-xp-db.dts @@ -75,7 +75,9 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 - MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000>; + MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000 + MBUS_ID(0x09, 0x09) 0 0 0xf8100000 0x10000 + MBUS_ID(0x09, 0x05) 0 0 0xf8110000 0x10000>; devbus-bootcs { status = "okay"; diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts index bf724ca96a33..4878d7353069 100644 --- a/arch/arm/boot/dts/armada-xp-gp.dts +++ b/arch/arm/boot/dts/armada-xp-gp.dts @@ -94,7 +94,9 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 - MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000>; + MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000 + MBUS_ID(0x09, 0x09) 0 0 0xf8100000 0x10000 + MBUS_ID(0x09, 0x05) 0 0 0xf8110000 0x10000>; devbus-bootcs { status = "okay"; diff --git a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts index 06a6a6c1fdf7..58b500873bfd 100644 --- a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts +++ b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts @@ -64,7 +64,9 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000 - MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x09) 0 0 0xf8100000 0x10000 + MBUS_ID(0x09, 0x05) 0 0 0xf8110000 0x10000>; pcie-controller { status = "okay"; diff --git a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts index fdd187c55aa5..6e9820e141f8 100644 --- a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts +++ b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts @@ -69,7 +69,9 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x09) 0 0 0xf8100000 0x10000 + MBUS_ID(0x09, 0x05) 0 0 0xf8110000 0x10000>; pcie-controller { status = "okay"; diff --git a/arch/arm/boot/dts/armada-xp-matrix.dts b/arch/arm/boot/dts/armada-xp-matrix.dts index f894bc83e957..6ab33837a2b6 100644 --- a/arch/arm/boot/dts/armada-xp-matrix.dts +++ b/arch/arm/boot/dts/armada-xp-matrix.dts @@ -67,7 +67,9 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x09) 0 0 0xf8100000 0x10000 + MBUS_ID(0x09, 0x05) 0 0 0xf8110000 0x10000>; internal-regs { serial@12000 { diff --git a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts b/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts index 1516fc2627f9..6fe8972de0a2 100644 --- a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts +++ b/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts @@ -63,7 +63,9 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000 - MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x09) 0 0 0xf8100000 0x10000 + MBUS_ID(0x09, 0x05) 0 0 0xf8110000 0x10000>; pcie-controller { status = "okay"; @@ -88,41 +90,10 @@ }; internal-regs { - /* Two rear eSATA ports */ - sata@a0000 { - nr-ports = <2>; - status = "okay"; - }; - - serial@12000 { - status = "okay"; - }; - - mdio { - phy0: ethernet-phy@0 { /* Marvell 88E1318 */ - reg = <0>; - }; - - phy1: ethernet-phy@1 { /* Marvell 88E1318 */ - reg = <1>; - }; - }; - - ethernet@70000 { - status = "okay"; - phy = <&phy0>; - phy-mode = "rgmii-id"; - }; - ethernet@74000 { - status = "okay"; - phy = <&phy1>; - phy-mode = "rgmii-id"; - }; - - /* Front USB 2.0 port */ - usb@50000 { - status = "okay"; + /* RTC is provided by Intersil ISL12057 I2C RTC chip */ + rtc@10300 { + status = "disabled"; }; i2c@11000 { @@ -130,12 +101,6 @@ clock-frequency = <400000>; status = "okay"; - isl12057: isl12057@68 { - compatible = "isil,isl12057"; - reg = <0x68>; - isil,irq2-can-wakeup-machine; - }; - /* Controller for rear fan #1 of 3 (Protechnic * MGT4012XB-O20, 8000RPM) near eSATA port */ g762_fan1: g762@3e { @@ -172,6 +137,49 @@ compatible = "gmt,g751"; reg = <0x4c>; }; + + isl12057: isl12057@68 { + compatible = "isil,isl12057"; + reg = <0x68>; + isil,irq2-can-wakeup-machine; + }; + }; + + serial@12000 { + status = "okay"; + }; + + /* Front USB 2.0 port */ + usb@50000 { + status = "okay"; + }; + + mdio { + phy0: ethernet-phy@0 { /* Marvell 88E1318 */ + reg = <0>; + }; + + phy1: ethernet-phy@1 { /* Marvell 88E1318 */ + reg = <1>; + }; + }; + + ethernet@70000 { + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; + }; + + ethernet@74000 { + status = "okay"; + phy = <&phy1>; + phy-mode = "rgmii-id"; + }; + + /* Two rear eSATA ports */ + sata@a0000 { + nr-ports = <2>; + status = "okay"; }; nand@d0000 { diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts index 990e8a2100f0..a5db17782e08 100644 --- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts +++ b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts @@ -65,7 +65,9 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000 MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 - MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x8000000>; + MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x8000000 + MBUS_ID(0x09, 0x09) 0 0 0xf8100000 0x10000 + MBUS_ID(0x09, 0x05) 0 0 0xf8110000 0x10000>; devbus-bootcs { status = "okay"; diff --git a/arch/arm/boot/dts/armada-xp-synology-ds414.dts b/arch/arm/boot/dts/armada-xp-synology-ds414.dts index 20267ad2f61e..2391b11dc546 100644 --- a/arch/arm/boot/dts/armada-xp-synology-ds414.dts +++ b/arch/arm/boot/dts/armada-xp-synology-ds414.dts @@ -77,7 +77,9 @@ soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>; + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x09) 0 0 0xf8100000 0x10000 + MBUS_ID(0x09, 0x05) 0 0 0xf8110000 0x10000>; pcie-controller { status = "okay"; diff --git a/arch/arm/boot/dts/armada-xp.dtsi b/arch/arm/boot/dts/armada-xp.dtsi index 3de9b761cc1a..be23196829bb 100644 --- a/arch/arm/boot/dts/armada-xp.dtsi +++ b/arch/arm/boot/dts/armada-xp.dtsi @@ -184,6 +184,11 @@ reg = <0x20800 0x20>; }; + cpu-config@21000 { + compatible = "marvell,armada-xp-cpu-config"; + reg = <0x21000 0x8>; + }; + eth2: ethernet@30000 { compatible = "marvell,armada-xp-neta"; reg = <0x30000 0x4000>; @@ -236,6 +241,18 @@ compatible = "marvell,armada-xp-neta"; }; + crypto@90000 { + compatible = "marvell,armada-xp-crypto"; + reg = <0x90000 0x10000>; + reg-names = "regs"; + interrupts = <48>, <49>; + clocks = <&gateclk 23>, <&gateclk 23>; + clock-names = "cesa0", "cesa1"; + marvell,crypto-srams = <&crypto_sram0>, + <&crypto_sram1>; + marvell,crypto-sram-size = <0x800>; + }; + xor@f0900 { compatible = "marvell,orion-xor"; reg = <0xF0900 0x100 @@ -256,6 +273,24 @@ }; }; }; + + crypto_sram0: sa-sram0 { + compatible = "mmio-sram"; + reg = <MBUS_ID(0x09, 0x09) 0 0x800>; + clocks = <&gateclk 23>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0x09, 0x09) 0 0x800>; + }; + + crypto_sram1: sa-sram1 { + compatible = "mmio-sram"; + reg = <MBUS_ID(0x09, 0x05) 0 0x800>; + clocks = <&gateclk 23>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0x09, 0x05) 0 0x800>; + }; }; clocks { diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts index e8d63afdb135..e07c2b206beb 100644 --- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts @@ -44,6 +44,7 @@ */ /dts-v1/; #include "sama5d2.dtsi" +#include "sama5d2-pinfunc.h" / { model = "Atmel SAMA5D2 Xplained"; @@ -92,6 +93,8 @@ apb { spi0: spi@f8000000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi0_default>; status = "okay"; m25p80@0 { @@ -102,25 +105,92 @@ }; macb0: ethernet@f8008000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_macb0_default>; phy-mode = "rmii"; status = "okay"; }; uart1: serial@f8020000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1_default>; status = "okay"; }; i2c0: i2c@f8028000 { dmas = <0>, <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c0_default>; status = "okay"; + + pmic: act8865@5b { + compatible = "active-semi,act8865"; + reg = <0x5b>; + active-semi,vsel-high; + status = "okay"; + + regulators { + vdd_1v35_reg: DCDC_REG1 { + regulator-name = "VDD_1V35"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + vdd_1v2_reg: DCDC_REG2 { + regulator-name = "VDD_1V2"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + }; + + vdd_3v3_reg: DCDC_REG3 { + regulator-name = "VDD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_fuse_reg: LDO_REG1 { + regulator-name = "VDD_FUSE"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + vdd_3v3_lp_reg: LDO_REG2 { + regulator-name = "VDD_3V3_LP"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_led_reg: LDO_REG3 { + regulator-name = "VDD_LED"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_sdhc_1v8_reg: LDO_REG4 { + regulator-name = "VDD_SDHC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + }; }; uart3: serial@fc008000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3_default>; status = "okay"; }; i2c1: i2c@fc028000 { dmas = <0>, <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1_default>; status = "okay"; at24@54 { @@ -129,6 +199,54 @@ pagesize = <16>; }; }; + + pinctrl@fc038000 { + pinctrl_i2c0_default: i2c0_default { + pinmux = <PIN_PD21__TWD0>, + <PIN_PD22__TWCK0>; + bias-disable; + }; + + pinctrl_i2c1_default: i2c1_default { + pinmux = <PIN_PD4__TWD1>, + <PIN_PD5__TWCK1>; + bias-disable; + }; + + pinctrl_macb0_default: macb0_default { + pinmux = <PIN_PB14__GTXCK>, + <PIN_PB15__GTXEN>, + <PIN_PB16__GRXDV>, + <PIN_PB17__GRXER>, + <PIN_PB18__GRX0>, + <PIN_PB19__GRX1>, + <PIN_PB20__GTX0>, + <PIN_PB21__GTX1>, + <PIN_PB22__GMDC>, + <PIN_PB23__GMDIO>; + bias-disable; + }; + + pinctrl_spi0_default: spi0_default { + pinmux = <PIN_PA14__SPI0_SPCK>, + <PIN_PA15__SPI0_MOSI>, + <PIN_PA16__SPI0_MISO>, + <PIN_PA17__SPI0_NPCS0>; + bias-disable; + }; + + pinctrl_uart1_default: uart1_default { + pinmux = <PIN_PD2__URXD1>, + <PIN_PD3__UTXD1>; + bias-disable; + }; + + pinctrl_uart3_default: uart3_default { + pinmux = <PIN_PB11__URXD3>, + <PIN_PB12__UTXD3>; + bias-disable; + }; + }; }; }; }; diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/at91-sama5d3_xplained.dts index d81474e0bcd6..8488ac53d22d 100644 --- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d3_xplained.dts @@ -76,7 +76,7 @@ pmic: act8865@5b { compatible = "active-semi,act8865"; reg = <0x5b>; - status = "okay"; + status = "disabled"; regulators { vcc_1v8_reg: DCDC_REG1 { diff --git a/arch/arm/boot/dts/at91-sama5d4_xplained.dts b/arch/arm/boot/dts/at91-sama5d4_xplained.dts index 07f46963335b..45371a1b61b3 100644 --- a/arch/arm/boot/dts/at91-sama5d4_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d4_xplained.dts @@ -246,7 +246,7 @@ d8 { label = "d8"; gpios = <&pioD 30 GPIO_ACTIVE_HIGH>; - status = "disabled"; + default-state = "on"; }; d10 { diff --git a/arch/arm/boot/dts/at91-sama5d4ek.dts b/arch/arm/boot/dts/at91-sama5d4ek.dts index 49a59c7e4a5d..6d272c0125e3 100644 --- a/arch/arm/boot/dts/at91-sama5d4ek.dts +++ b/arch/arm/boot/dts/at91-sama5d4ek.dts @@ -148,6 +148,25 @@ clocks = <&pck2>; clock-names = "mclk"; }; + + qt1070:keyboard@1b { + compatible = "qt1070"; + reg = <0x1b>; + interrupt-parent = <&pioE>; + interrupts = <25 0x0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qt1070_irq>; + wakeup-source; + }; + + atmel_mxt_ts@4c { + compatible = "atmel,atmel_mxt_ts"; + reg = <0x4c>; + interrupt-parent = <&pioE>; + interrupts = <24 0x0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mxt_ts>; + }; }; macb0: ethernet@f8020000 { @@ -204,6 +223,14 @@ atmel,pins = <AT91_PIOE 13 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PE13 gpio */ }; + pinctrl_qt1070_irq: qt1070_irq { + atmel,pins = + <AT91_PIOE 25 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; + }; + pinctrl_mxt_ts: mxt_irq { + atmel,pins = + <AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; + }; }; }; }; diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/at91rm9200.dtsi index 60edd8baebb8..f6cb7a80a2f5 100644 --- a/arch/arm/boot/dts/at91rm9200.dtsi +++ b/arch/arm/boot/dts/at91rm9200.dtsi @@ -97,7 +97,7 @@ }; pmc: pmc@fffffc00 { - compatible = "atmel,at91rm9200-pmc"; + compatible = "atmel,at91rm9200-pmc", "syscon"; reg = <0xfffffc00 0x100>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; interrupt-controller; @@ -426,7 +426,7 @@ pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; clocks = <&ssc0_clk>; clock-names = "pclk"; - status = "disable"; + status = "disabled"; }; ssc1: ssc@fffd4000 { @@ -437,7 +437,7 @@ pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; clocks = <&ssc1_clk>; clock-names = "pclk"; - status = "disable"; + status = "disabled"; }; ssc2: ssc@fffd8000 { @@ -448,7 +448,7 @@ pinctrl-0 = <&pinctrl_ssc2_tx &pinctrl_ssc2_rx>; clocks = <&ssc2_clk>; clock-names = "pclk"; - status = "disable"; + status = "disabled"; }; macb0: ethernet@fffbc000 { diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi index be9c027ddd97..d4884dd1c243 100644 --- a/arch/arm/boot/dts/at91sam9260.dtsi +++ b/arch/arm/boot/dts/at91sam9260.dtsi @@ -100,7 +100,7 @@ }; pmc: pmc@fffffc00 { - compatible = "atmel,at91sam9260-pmc"; + compatible = "atmel,at91sam9260-pmc", "syscon"; reg = <0xfffffc00 0x100>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; interrupt-controller; diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi index ce1e3e94a40c..5e09de4eb9cd 100644 --- a/arch/arm/boot/dts/at91sam9261.dtsi +++ b/arch/arm/boot/dts/at91sam9261.dtsi @@ -568,7 +568,7 @@ }; pmc: pmc@fffffc00 { - compatible = "atmel,at91rm9200-pmc"; + compatible = "atmel,at91rm9200-pmc", "syscon"; reg = <0xfffffc00 0x100>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; interrupt-controller; diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi index f1f5fa3a9e6e..93446420af25 100644 --- a/arch/arm/boot/dts/at91sam9263.dtsi +++ b/arch/arm/boot/dts/at91sam9263.dtsi @@ -93,7 +93,7 @@ }; pmc: pmc@fffffc00 { - compatible = "atmel,at91rm9200-pmc"; + compatible = "atmel,at91rm9200-pmc", "syscon"; reg = <0xfffffc00 0x100>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; interrupt-controller; diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi index 18b8b9e29704..af8b708ac312 100644 --- a/arch/arm/boot/dts/at91sam9g45.dtsi +++ b/arch/arm/boot/dts/at91sam9g45.dtsi @@ -114,7 +114,7 @@ }; pmc: pmc@fffffc00 { - compatible = "atmel,at91sam9g45-pmc"; + compatible = "atmel,at91sam9g45-pmc", "syscon"; reg = <0xfffffc00 0x100>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; interrupt-controller; diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts index d1ae60a855d4..9d16ef8453c5 100644 --- a/arch/arm/boot/dts/at91sam9m10g45ek.dts +++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts @@ -198,6 +198,8 @@ isi_0: endpoint { remote-endpoint = <&ov2640_0>; bus-width = <8>; + vsync-active = <1>; + hsync-active = <1>; }; }; }; diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi index 32bc9a189db0..95569a87b6c9 100644 --- a/arch/arm/boot/dts/at91sam9n12.dtsi +++ b/arch/arm/boot/dts/at91sam9n12.dtsi @@ -97,7 +97,7 @@ }; pmc: pmc@fffffc00 { - compatible = "atmel,at91sam9n12-pmc"; + compatible = "atmel,at91sam9n12-pmc", "syscon"; reg = <0xfffffc00 0x200>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; interrupt-controller; diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts index efa75064d38a..acf3451a332d 100644 --- a/arch/arm/boot/dts/at91sam9n12ek.dts +++ b/arch/arm/boot/dts/at91sam9n12ek.dts @@ -71,10 +71,6 @@ }; }; - i2c1: i2c@f8014000 { - status = "okay"; - }; - mmc0: mmc@f0008000 { pinctrl-0 = < &pinctrl_board_mmc0 @@ -204,13 +200,13 @@ }; d9 { - label = "d6"; + label = "d9"; gpios = <&pioB 5 GPIO_ACTIVE_LOW>; linux,default-trigger = "nand-disk"; }; d10 { - label = "d7"; + label = "d10"; gpios = <&pioB 6 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi index a0b90aedd3b8..6d829db4e887 100644 --- a/arch/arm/boot/dts/at91sam9rl.dtsi +++ b/arch/arm/boot/dts/at91sam9rl.dtsi @@ -814,7 +814,7 @@ }; pmc: pmc@fffffc00 { - compatible = "atmel,at91sam9g45-pmc"; + compatible = "atmel,at91sam9g45-pmc", "syscon"; reg = <0xfffffc00 0x100>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; interrupt-controller; diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi index 747d8f070a5c..0827d594b1f0 100644 --- a/arch/arm/boot/dts/at91sam9x5.dtsi +++ b/arch/arm/boot/dts/at91sam9x5.dtsi @@ -68,7 +68,7 @@ adc_op_clk: adc_op_clk{ compatible = "fixed-clock"; #clock-cells = <0>; - clock-frequency = <5000000>; + clock-frequency = <1000000>; }; }; @@ -105,7 +105,7 @@ }; pmc: pmc@fffffc00 { - compatible = "atmel,at91sam9x5-pmc"; + compatible = "atmel,at91sam9x5-pmc", "syscon"; reg = <0xfffffc00 0x100>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; interrupt-controller; @@ -1043,6 +1043,7 @@ atmel,adc-channels-used = <0xffff>; atmel,adc-vref = <3300>; atmel,adc-startup-time = <40>; + atmel,adc-sample-hold-time = <11>; atmel,adc-res = <8 10>; atmel,adc-res-names = "lowres", "highres"; atmel,adc-use-res = "highres"; diff --git a/arch/arm/boot/dts/at91sam9x5ek.dtsi b/arch/arm/boot/dts/at91sam9x5ek.dtsi index d237c462dfc6..52425a4ca97e 100644 --- a/arch/arm/boot/dts/at91sam9x5ek.dtsi +++ b/arch/arm/boot/dts/at91sam9x5ek.dtsi @@ -66,6 +66,8 @@ isi_0: endpoint@0 { remote-endpoint = <&ov2640_0>; bus-width = <8>; + vsync-active = <1>; + hsync-active = <1>; }; }; }; @@ -100,6 +102,12 @@ }; }; + adc0: adc@f804c000 { + atmel,adc-ts-wires = <4>; + atmel,adc-ts-pressure-threshold = <10000>; + status = "okay"; + }; + pinctrl@fffff400 { camera_sensor { pinctrl_pck0_as_isi_mck: pck0_as_isi_mck-0 { diff --git a/arch/arm/boot/dts/axp209.dtsi b/arch/arm/boot/dts/axp209.dtsi index 24c935c72e5e..051ab3ba9a65 100644 --- a/arch/arm/boot/dts/axp209.dtsi +++ b/arch/arm/boot/dts/axp209.dtsi @@ -89,4 +89,9 @@ regulator-name = "ldo5"; }; }; + + usb_power_supply: usb_power_supply { + compatible = "x-powers,axp202-usb-power-supply"; + status = "disabled"; + }; }; diff --git a/arch/arm/boot/dts/axp22x.dtsi b/arch/arm/boot/dts/axp22x.dtsi new file mode 100644 index 000000000000..76302f58c478 --- /dev/null +++ b/arch/arm/boot/dts/axp22x.dtsi @@ -0,0 +1,143 @@ +/* + * Copyright 2015 Chen-Yu Tsai + * + * Chen-Yu Tsai <wens@csie.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/* + * AXP221/221s/223 Integrated Power Management Chip + * http://www.x-powers.com/product/AXP22X.php + * http://dl.linux-sunxi.org/AXP/AXP221%20Datasheet%20V1.2%2020130326%20.pdf + */ + +&axp22x { + interrupt-controller; + #interrupt-cells = <1>; + + regulators { + /* Default work frequency for buck regulators */ + x-powers,dcdc-freq = <3000>; + + reg_dcdc1: dcdc1 { + regulator-name = "dcdc1"; + }; + + reg_dcdc2: dcdc2 { + regulator-name = "dcdc2"; + }; + + reg_dcdc3: dcdc3 { + regulator-name = "dcdc3"; + }; + + reg_dcdc4: dcdc4 { + regulator-name = "dcdc4"; + }; + + reg_dcdc5: dcdc5 { + regulator-name = "dcdc5"; + }; + + reg_dc1sw: dc1sw { + regulator-name = "dc1sw"; + }; + + reg_dc5ldo: dc5ldo { + regulator-name = "dc5ldo"; + }; + + reg_aldo1: aldo1 { + regulator-name = "aldo1"; + }; + + reg_aldo2: aldo2 { + regulator-name = "aldo2"; + }; + + reg_aldo3: aldo3 { + regulator-name = "aldo3"; + }; + + reg_dldo1: dldo1 { + regulator-name = "dldo1"; + }; + + reg_dldo2: dldo2 { + regulator-name = "dldo2"; + }; + + reg_dldo3: dldo3 { + regulator-name = "dldo3"; + }; + + reg_dldo4: dldo4 { + regulator-name = "dldo4"; + }; + + reg_eldo1: eldo1 { + regulator-name = "eldo1"; + }; + + reg_eldo2: eldo2 { + regulator-name = "eldo2"; + }; + + reg_eldo3: eldo3 { + regulator-name = "eldo3"; + }; + + reg_ldo_io0: ldo_io0 { + regulator-name = "ldo_io0"; + }; + + reg_ldo_io1: ldo_io1 { + regulator-name = "ldo_io1"; + }; + + reg_rtc_ldo: rtc_ldo { + /* RTC_LDO is a fixed, always-on regulator */ + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "rtc_ldo"; + }; + }; +}; diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi index e1ac07a16f92..2778533502d9 100644 --- a/arch/arm/boot/dts/bcm-cygnus.dtsi +++ b/arch/arm/boot/dts/bcm-cygnus.dtsi @@ -32,6 +32,7 @@ #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/clock/bcm-cygnus.h> #include "skeleton.dtsi" @@ -54,197 +55,212 @@ /include/ "bcm-cygnus-clock.dtsi" - pinctrl: pinctrl@0x0301d0c8 { - compatible = "brcm,cygnus-pinmux"; - reg = <0x0301d0c8 0x30>, - <0x0301d24c 0x2c>; - }; - - gpio_crmu: gpio@03024800 { - compatible = "brcm,cygnus-crmu-gpio"; - reg = <0x03024800 0x50>, - <0x03024008 0x18>; - #gpio-cells = <2>; - gpio-controller; - }; - - gpio_ccm: gpio@1800a000 { - compatible = "brcm,cygnus-ccm-gpio"; - reg = <0x1800a000 0x50>, - <0x0301d164 0x20>; - #gpio-cells = <2>; - gpio-controller; - interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; - interrupt-controller; - }; + core { + compatible = "simple-bus"; + ranges = <0x00000000 0x19000000 0x1000000>; + #address-cells = <1>; + #size-cells = <1>; - gpio_asiu: gpio@180a5000 { - compatible = "brcm,cygnus-asiu-gpio"; - reg = <0x180a5000 0x668>; - #gpio-cells = <2>; - gpio-controller; + timer@20200 { + compatible = "arm,cortex-a9-global-timer"; + reg = <0x20200 0x100>; + interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&periph_clk>; + }; - pinmux = <&pinctrl>; + gic: interrupt-controller@21000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #address-cells = <0>; + interrupt-controller; + reg = <0x21000 0x1000>, + <0x20100 0x100>; + }; - interrupt-controller; - interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; + L2: l2-cache { + compatible = "arm,pl310-cache"; + reg = <0x22000 0x1000>; + cache-unified; + cache-level = <2>; + }; }; - amba { + axi { + compatible = "simple-bus"; + ranges; #address-cells = <1>; #size-cells = <1>; - compatible = "arm,amba-bus", "simple-bus"; - interrupt-parent = <&gic>; - ranges; - wdt@18009000 { - compatible = "arm,sp805" , "arm,primecell"; - reg = <0x18009000 0x1000>; - interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&axi81_clk>; - clock-names = "apb_pclk"; + pinctrl: pinctrl@0x0301d0c8 { + compatible = "brcm,cygnus-pinmux"; + reg = <0x0301d0c8 0x30>, + <0x0301d24c 0x2c>; }; - }; - i2c0: i2c@18008000 { - compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c"; - reg = <0x18008000 0x100>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>; - clock-frequency = <100000>; - status = "disabled"; - }; + gpio_crmu: gpio@03024800 { + compatible = "brcm,cygnus-crmu-gpio"; + reg = <0x03024800 0x50>, + <0x03024008 0x18>; + #gpio-cells = <2>; + gpio-controller; + }; - i2c1: i2c@1800b000 { - compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c"; - reg = <0x1800b000 0x100>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>; - clock-frequency = <100000>; - status = "disabled"; - }; + i2c0: i2c@18008000 { + compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c"; + reg = <0x18008000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>; + clock-frequency = <100000>; + status = "disabled"; + }; - pcie0: pcie@18012000 { - compatible = "brcm,iproc-pcie"; - reg = <0x18012000 0x1000>; + wdt0: wdt@18009000 { + compatible = "arm,sp805" , "arm,primecell"; + reg = <0x18009000 0x1000>; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&axi81_clk>; + clock-names = "apb_pclk"; + }; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>; + gpio_ccm: gpio@1800a000 { + compatible = "brcm,cygnus-ccm-gpio"; + reg = <0x1800a000 0x50>, + <0x0301d164 0x20>; + #gpio-cells = <2>; + gpio-controller; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + }; - linux,pci-domain = <0>; + i2c1: i2c@1800b000 { + compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c"; + reg = <0x1800b000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>; + clock-frequency = <100000>; + status = "disabled"; + }; - bus-range = <0x00 0xff>; + pcie0: pcie@18012000 { + compatible = "brcm,iproc-pcie"; + reg = <0x18012000 0x1000>; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - ranges = <0x81000000 0 0 0x28000000 0 0x00010000 - 0x82000000 0 0x20000000 0x20000000 0 0x04000000>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>; - status = "disabled"; - }; + linux,pci-domain = <0>; - pcie1: pcie@18013000 { - compatible = "brcm,iproc-pcie"; - reg = <0x18013000 0x1000>; + bus-range = <0x00 0xff>; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x28000000 0 0x00010000 + 0x82000000 0 0x20000000 0x20000000 0 0x04000000>; - linux,pci-domain = <1>; + status = "disabled"; + }; - bus-range = <0x00 0xff>; + pcie1: pcie@18013000 { + compatible = "brcm,iproc-pcie"; + reg = <0x18013000 0x1000>; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - ranges = <0x81000000 0 0 0x48000000 0 0x00010000 - 0x82000000 0 0x40000000 0x40000000 0 0x04000000>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>; - status = "disabled"; - }; + linux,pci-domain = <1>; - uart0: serial@18020000 { - compatible = "snps,dw-apb-uart"; - reg = <0x18020000 0x100>; - reg-shift = <2>; - reg-io-width = <4>; - interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&axi81_clk>; - clock-frequency = <100000000>; - status = "disabled"; - }; + bus-range = <0x00 0xff>; - uart1: serial@18021000 { - compatible = "snps,dw-apb-uart"; - reg = <0x18021000 0x100>; - reg-shift = <2>; - reg-io-width = <4>; - interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&axi81_clk>; - clock-frequency = <100000000>; - status = "disabled"; - }; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x48000000 0 0x00010000 + 0x82000000 0 0x40000000 0x40000000 0 0x04000000>; - uart2: serial@18022000 { - compatible = "snps,dw-apb-uart"; - reg = <0x18020000 0x100>; - reg-shift = <2>; - reg-io-width = <4>; - interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&axi81_clk>; - clock-frequency = <100000000>; - status = "disabled"; - }; + status = "disabled"; + }; - uart3: serial@18023000 { - compatible = "snps,dw-apb-uart"; - reg = <0x18023000 0x100>; - reg-shift = <2>; - reg-io-width = <4>; - interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&axi81_clk>; - clock-frequency = <100000000>; - status = "disabled"; - }; + uart0: serial@18020000 { + compatible = "snps,dw-apb-uart"; + reg = <0x18020000 0x100>; + reg-shift = <2>; + reg-io-width = <4>; + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&axi81_clk>; + clock-frequency = <100000000>; + status = "disabled"; + }; - nand: nand@18046000 { - compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1", "brcm,brcmnand"; - reg = <0x18046000 0x600>, <0xf8105408 0x600>, <0x18046f00 0x20>; - reg-names = "nand", "iproc-idm", "iproc-ext"; - interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; + uart1: serial@18021000 { + compatible = "snps,dw-apb-uart"; + reg = <0x18021000 0x100>; + reg-shift = <2>; + reg-io-width = <4>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&axi81_clk>; + clock-frequency = <100000000>; + status = "disabled"; + }; - #address-cells = <1>; - #size-cells = <0>; + uart2: serial@18022000 { + compatible = "snps,dw-apb-uart"; + reg = <0x18020000 0x100>; + reg-shift = <2>; + reg-io-width = <4>; + interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&axi81_clk>; + clock-frequency = <100000000>; + status = "disabled"; + }; - brcm,nand-has-wp; - }; + uart3: serial@18023000 { + compatible = "snps,dw-apb-uart"; + reg = <0x18023000 0x100>; + reg-shift = <2>; + reg-io-width = <4>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&axi81_clk>; + clock-frequency = <100000000>; + status = "disabled"; + }; - gic: interrupt-controller@19021000 { - compatible = "arm,cortex-a9-gic"; - #interrupt-cells = <3>; - #address-cells = <0>; - interrupt-controller; - reg = <0x19021000 0x1000>, - <0x19020100 0x100>; - }; + nand: nand@18046000 { + compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1"; + reg = <0x18046000 0x600>, <0xf8105408 0x600>, + <0x18046f00 0x20>; + reg-names = "nand", "iproc-idm", "iproc-ext"; + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; - L2: l2-cache { - compatible = "arm,pl310-cache"; - reg = <0x19022000 0x1000>; - cache-unified; - cache-level = <2>; - }; + #address-cells = <1>; + #size-cells = <0>; - timer@19020200 { - compatible = "arm,cortex-a9-global-timer"; - reg = <0x19020200 0x100>; - interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&periph_clk>; - }; + brcm,nand-has-wp; + }; + gpio_asiu: gpio@180a5000 { + compatible = "brcm,cygnus-asiu-gpio"; + reg = <0x180a5000 0x668>; + #gpio-cells = <2>; + gpio-controller; + + pinmux = <&pinctrl>; + + interrupt-controller; + interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; + }; + + touchscreen: tsc@180a6000 { + compatible = "brcm,iproc-touchscreen"; + reg = <0x180a6000 0x40>; + clocks = <&asiu_clks BCM_CYGNUS_ASIU_ADC_CLK>; + clock-names = "tsc_clk"; + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + }; }; diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi new file mode 100644 index 000000000000..58aca277e4a7 --- /dev/null +++ b/arch/arm/boot/dts/bcm-nsp.dtsi @@ -0,0 +1,119 @@ +/* + * BSD LICENSE + * + * Copyright(c) 2015 Broadcom Corporation. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name of Broadcom Corporation nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/interrupt-controller/irq.h> + +#include "skeleton.dtsi" + +/ { + compatible = "brcm,nsp"; + model = "Broadcom Northstar Plus SoC"; + interrupt-parent = <&gic>; + + mpcore { + compatible = "simple-bus"; + ranges = <0x00000000 0x19020000 0x00003000>; + #address-cells = <1>; + #size-cells = <1>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + next-level-cache = <&L2>; + reg = <0x0>; + }; + }; + + L2: l2-cache { + compatible = "arm,pl310-cache"; + reg = <0x2000 0x1000>; + cache-unified; + cache-level = <2>; + }; + + gic: interrupt-controller@19021000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #address-cells = <0>; + interrupt-controller; + reg = <0x1000 0x1000>, + <0x0100 0x100>; + }; + + timer@19020200 { + compatible = "arm,cortex-a9-global-timer"; + reg = <0x0200 0x100>; + interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&periph_clk>; + }; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + periph_clk: periph_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <500000000>; + }; + }; + + axi { + compatible = "simple-bus"; + ranges = <0x00000000 0x18000000 0x00001000>; + #address-cells = <1>; + #size-cells = <1>; + + uart0: serial@18000300 { + compatible = "ns16550a"; + reg = <0x0300 0x100>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <62499840>; + status = "disabled"; + }; + + uart1: serial@18000400 { + compatible = "ns16550a"; + reg = <0x0400 0x100>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <62499840>; + status = "disabled"; + }; + }; +}; diff --git a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts new file mode 100644 index 000000000000..b2bff43b135c --- /dev/null +++ b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts @@ -0,0 +1,30 @@ +/dts-v1/; +#include "bcm2835-rpi.dtsi" + +/ { + compatible = "raspberrypi,model-a-plus", "brcm,bcm2835"; + model = "Raspberry Pi Model A+"; + + leds { + act { + gpios = <&gpio 47 0>; + }; + + pwr { + label = "PWR"; + gpios = <&gpio 35 0>; + default-state = "keep"; + linux,default-trigger = "default-on"; + }; + }; +}; + +&gpio { + pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>; + + /* I2S interface */ + i2s_alt0: i2s_alt0 { + brcm,pins = <18 19 20 21>; + brcm,function = <BCM2835_FSEL_ALT0>; + }; +}; diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts new file mode 100644 index 000000000000..eab8b5916e8a --- /dev/null +++ b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts @@ -0,0 +1,23 @@ +/dts-v1/; +#include "bcm2835-rpi.dtsi" + +/ { + compatible = "raspberrypi,model-b-rev2", "brcm,bcm2835"; + model = "Raspberry Pi Model B rev2"; + + leds { + act { + gpios = <&gpio 16 1>; + }; + }; +}; + +&gpio { + pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>; + + /* I2S interface */ + i2s_alt2: i2s_alt2 { + brcm,pins = <28 29 30 31>; + brcm,function = <BCM2835_FSEL_ALT2>; + }; +}; diff --git a/arch/arm/boot/dts/bcm2835-rpi-b.dts b/arch/arm/boot/dts/bcm2835-rpi-b.dts index ee89b79426cf..ff6b2d1c6c90 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-b.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-b.dts @@ -13,11 +13,5 @@ }; &gpio { - pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>; - - /* I2S interface */ - i2s_alt2: i2s_alt2 { - brcm,pins = <28 29 30 31>; - brcm,function = <BCM2835_FSEL_ALT2>; - }; + pinctrl-0 = <&gpioout &alt0 &alt3>; }; diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi index ab5474e5d1c8..3572f0367baf 100644 --- a/arch/arm/boot/dts/bcm2835-rpi.dtsi +++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi @@ -52,6 +52,10 @@ clock-frequency = <100000>; }; +&i2c2 { + status = "okay"; +}; + &sdhci { status = "okay"; bus-width = <4>; diff --git a/arch/arm/boot/dts/bcm2835.dtsi b/arch/arm/boot/dts/bcm2835.dtsi index 301c73f4ca33..aef64de77495 100644 --- a/arch/arm/boot/dts/bcm2835.dtsi +++ b/arch/arm/boot/dts/bcm2835.dtsi @@ -1,4 +1,5 @@ #include <dt-bindings/pinctrl/bcm2835.h> +#include <dt-bindings/clock/bcm2835.h> #include "skeleton.dtsi" / { @@ -21,6 +22,10 @@ compatible = "brcm,bcm2835-system-timer"; reg = <0x7e003000 0x1000>; interrupts = <1 0>, <1 1>, <1 2>, <1 3>; + /* This could be a reference to BCM2835_CLOCK_TIMER, + * but we don't have the driver using the common clock + * support yet. + */ clock-frequency = <1000000>; }; @@ -57,6 +62,17 @@ reg = <0x7e100000 0x28>; }; + clocks: cprman@7e101000 { + compatible = "brcm,bcm2835-cprman"; + #clock-cells = <1>; + reg = <0x7e101000 0x2000>; + + /* CPRMAN derives everything from the platform's + * oscillator. + */ + clocks = <&clk_osc>; + }; + rng@7e104000 { compatible = "brcm,bcm2835-rng"; reg = <0x7e104000 0x10>; @@ -92,11 +108,13 @@ #interrupt-cells = <2>; }; - uart@7e201000 { + uart0: uart@7e201000 { compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell"; reg = <0x7e201000 0x1000>; interrupts = <2 25>; - clock-frequency = <3000000>; + clocks = <&clocks BCM2835_CLOCK_UART>, + <&clocks BCM2835_CLOCK_VPU>; + clock-names = "uartclk", "apb_pclk"; arm,primecell-periphid = <0x00241011>; }; @@ -115,7 +133,7 @@ compatible = "brcm,bcm2835-spi"; reg = <0x7e204000 0x1000>; interrupts = <2 22>; - clocks = <&clk_spi>; + clocks = <&clocks BCM2835_CLOCK_VPU>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -125,7 +143,7 @@ compatible = "brcm,bcm2835-i2c"; reg = <0x7e205000 0x1000>; interrupts = <2 21>; - clocks = <&clk_i2c>; + clocks = <&clocks BCM2835_CLOCK_VPU>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -135,7 +153,7 @@ compatible = "brcm,bcm2835-sdhci"; reg = <0x7e300000 0x100>; interrupts = <2 30>; - clocks = <&clk_mmc>; + clocks = <&clocks BCM2835_CLOCK_EMMC>; status = "disabled"; }; @@ -143,7 +161,17 @@ compatible = "brcm,bcm2835-i2c"; reg = <0x7e804000 0x1000>; interrupts = <2 21>; - clocks = <&clk_i2c>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@7e805000 { + compatible = "brcm,bcm2835-i2c"; + reg = <0x7e805000 0x1000>; + interrupts = <2 21>; + clocks = <&clocks BCM2835_CLOCK_VPU>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -165,28 +193,14 @@ #address-cells = <1>; #size-cells = <0>; - clk_mmc: clock@0 { + /* The oscillator is the root of the clock tree. */ + clk_osc: clock@3 { compatible = "fixed-clock"; - reg = <0>; + reg = <3>; #clock-cells = <0>; - clock-output-names = "mmc"; - clock-frequency = <100000000>; + clock-output-names = "osc"; + clock-frequency = <19200000>; }; - clk_i2c: clock@1 { - compatible = "fixed-clock"; - reg = <1>; - #clock-cells = <0>; - clock-output-names = "i2c"; - clock-frequency = <250000000>; - }; - - clk_spi: clock@2 { - compatible = "fixed-clock"; - reg = <2>; - #clock-cells = <0>; - clock-output-names = "spi"; - clock-frequency = <250000000>; - }; }; }; diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts index 64b8d10ccff8..ca92bba6a8c5 100644 --- a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts +++ b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts @@ -24,6 +24,17 @@ reg = <0x00000000 0x08000000>; }; + axi@18000000 { + usb3@23000 { + reg = <0x00023000 0x1000>; + + #address-cells = <1>; + #size-cells = <1>; + + vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>; + }; + }; + leds { compatible = "gpio-leds"; diff --git a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts index aedf3c426e1f..8ade7def2e8a 100644 --- a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts +++ b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts @@ -10,6 +10,7 @@ /dts-v1/; #include "bcm4708.dtsi" +#include "bcm5301x-nand-cs0-bch8.dtsi" / { compatible = "asus,rt-ac87u", "brcm,bcm4709", "brcm,bcm4708"; diff --git a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts new file mode 100644 index 000000000000..a22ed144040b --- /dev/null +++ b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts @@ -0,0 +1,106 @@ +/* + * Broadcom BCM470X / BCM5301X ARM platform code. + * DTS for Netgear R7000 + * + * Copyright (C) 2015 RafaÅ‚ MiÅ‚ecki <zajec5@gmail.com> + * + * Licensed under the GNU/GPL. See COPYING for details. + */ + +/dts-v1/; + +#include "bcm4708.dtsi" +#include "bcm5301x-nand-cs0-bch8.dtsi" + +/ { + compatible = "netgear,r7000", "brcm,bcm4709", "brcm,bcm4708"; + model = "Netgear R7000"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory { + reg = <0x00000000 0x08000000>; + }; + + leds { + compatible = "gpio-leds"; + + power-white { + label = "bcm53xx:white:power"; + gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-on"; + }; + + power-amber { + label = "bcm53xx:amber:power"; + gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-off"; + }; + + 5ghz { + label = "bcm53xx:white:5ghz"; + gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-off"; + }; + + 2ghz { + label = "bcm53xx:white:2ghz"; + gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-off"; + }; + + wps { + label = "bcm53xx:white:wps"; + gpios = <&chipcommon 14 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-off"; + }; + + wireless { + label = "bcm53xx:white:wireless"; + gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-off"; + }; + + usb3 { + label = "bcm53xx:white:usb3"; + gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-off"; + }; + + usb2 { + label = "bcm53xx:white:usb2"; + gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-off"; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + wps { + label = "WPS"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>; + }; + + rfkill { + label = "WiFi"; + linux,code = <KEY_RFKILL>; + gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>; + }; + + restart { + label = "Reset"; + linux,code = <KEY_RESTART>; + gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&uart0 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/bcm7445.dtsi b/arch/arm/boot/dts/bcm7445.dtsi index 3b6b17560687..4791321969b3 100644 --- a/arch/arm/boot/dts/bcm7445.dtsi +++ b/arch/arm/boot/dts/bcm7445.dtsi @@ -143,6 +143,12 @@ brcm,irq-can-wake; }; + aon-ctrl@410000 { + compatible = "brcm,brcmstb-aon-ctrl"; + reg = <0x410000 0x200>, <0x410200 0x400>; + reg-names = "aon-ctrl", "aon-sram"; + }; + nand: nand@3e2800 { status = "disabled"; #address-cells = <1>; @@ -219,6 +225,84 @@ }; + memory_controllers { + compatible = "simple-bus"; + ranges = <0x0 0x0 0xf1100000 0x200000>; + #address-cells = <1>; + #size-cells = <1>; + + memc@0 { + compatible = "brcm,brcmstb-memc", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x80000>; + + memc-ddr@2000 { + compatible = "brcm,brcmstb-memc-ddr"; + reg = <0x2000 0x800>; + }; + + ddr-phy@6000 { + compatible = "brcm,brcmstb-ddr-phy-v240.1"; + reg = <0x6000 0x21c>; + }; + + shimphy@8000 { + compatible = "brcm,brcmstb-ddr-shimphy-v1.0"; + reg = <0x8000 0xe4>; + }; + }; + + memc@1 { + compatible = "brcm,brcmstb-memc", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x80000 0x80000>; + + memc-ddr@2000 { + compatible = "brcm,brcmstb-memc-ddr"; + reg = <0x2000 0x800>; + }; + + ddr-phy@6000 { + compatible = "brcm,brcmstb-ddr-phy-v240.1"; + reg = <0x6000 0x21c>; + }; + + shimphy@8000 { + compatible = "brcm,brcmstb-ddr-shimphy-v1.0"; + reg = <0x8000 0xe4>; + }; + }; + + memc@2 { + compatible = "brcm,brcmstb-memc", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x100000 0x80000>; + + memc-ddr@2000 { + compatible = "brcm,brcmstb-memc-ddr"; + reg = <0x2000 0x800>; + }; + + ddr-phy@6000 { + compatible = "brcm,brcmstb-ddr-phy-v240.1"; + reg = <0x6000 0x21c>; + }; + + shimphy@8000 { + compatible = "brcm,brcmstb-ddr-shimphy-v1.0"; + reg = <0x8000 0xe4>; + }; + }; + }; + + sram@ffe00000 { + compatible = "brcm,boot-sram", "mmio-sram"; + reg = <0x0 0xffe00000 0x0 0x10000>; + }; + smpboot { compatible = "brcm,brcmstb-smpboot"; syscon-cpu = <&hif_cpubiuctrl 0x88 0x178>; diff --git a/arch/arm/boot/dts/bcm911360_entphn.dts b/arch/arm/boot/dts/bcm911360_entphn.dts index 7db484323fd6..8b3800f46288 100644 --- a/arch/arm/boot/dts/bcm911360_entphn.dts +++ b/arch/arm/boot/dts/bcm911360_entphn.dts @@ -39,19 +39,11 @@ model = "Cygnus Enterprise Phone (BCM911360_ENTPHN)"; compatible = "brcm,bcm11360", "brcm,cygnus"; - aliases { - serial0 = &uart3; - }; - chosen { stdout-path = &uart3; bootargs = "console=ttyS0,115200"; }; - uart3: serial@18023000 { - status = "okay"; - }; - gpio_keys { compatible = "gpio-keys"; #address-cells = <1>; @@ -64,3 +56,23 @@ }; }; }; + +&uart3 { + status = "okay"; +}; + +&nand { + nandcs@1 { + compatible = "brcm,nandcs"; + reg = <0>; + nand-on-flash-bbt; + + #address-cells = <1>; + #size-cells = <1>; + + nand-ecc-strength = <24>; + nand-ecc-step-size = <1024>; + + brcm,nand-oob-sector-size = <27>; + }; +}; diff --git a/arch/arm/boot/dts/bcm911360k.dts b/arch/arm/boot/dts/bcm911360k.dts index 9658d4f62d59..091c73a46e08 100644 --- a/arch/arm/boot/dts/bcm911360k.dts +++ b/arch/arm/boot/dts/bcm911360k.dts @@ -43,11 +43,10 @@ }; chosen { - stdout-path = &uart3; - bootargs = "console=ttyS0,115200"; + stdout-path = "serial0:115200n8"; }; +}; - uart3: serial@18023000 { - status = "okay"; - }; +&uart3 { + status = "okay"; }; diff --git a/arch/arm/boot/dts/bcm958300k.dts b/arch/arm/boot/dts/bcm958300k.dts index 2f63052f9d48..b4a1392bd5a6 100644 --- a/arch/arm/boot/dts/bcm958300k.dts +++ b/arch/arm/boot/dts/bcm958300k.dts @@ -33,6 +33,7 @@ /dts-v1/; #include "bcm-cygnus.dtsi" +#include "bcm9hmidc.dtsi" / { model = "Cygnus SVK (BCM958300K)"; @@ -43,35 +44,34 @@ }; chosen { - stdout-path = &uart3; - bootargs = "console=ttyS0,115200"; + stdout-path = "serial0:115200n8"; }; +}; - pcie0: pcie@18012000 { - status = "okay"; - }; +&pcie0 { + status = "okay"; +}; - pcie1: pcie@18013000 { - status = "okay"; - }; +&pcie1 { + status = "okay"; +}; - uart3: serial@18023000 { - status = "okay"; - }; +&uart3 { + status = "okay"; +}; - nand: nand@18046000 { - nandcs@1 { - compatible = "brcm,nandcs"; - reg = <0>; - nand-on-flash-bbt; +&nand { + nandcs@1 { + compatible = "brcm,nandcs"; + reg = <0>; + nand-on-flash-bbt; - #address-cells = <1>; - #size-cells = <1>; + #address-cells = <1>; + #size-cells = <1>; - nand-ecc-strength = <24>; - nand-ecc-step-size = <1024>; + nand-ecc-strength = <24>; + nand-ecc-step-size = <1024>; - brcm,nand-oob-sector-size = <27>; - }; + brcm,nand-oob-sector-size = <27>; }; }; diff --git a/arch/arm/boot/dts/bcm958305k.dts b/arch/arm/boot/dts/bcm958305k.dts index 56b429abbedb..3378683321d3 100644 --- a/arch/arm/boot/dts/bcm958305k.dts +++ b/arch/arm/boot/dts/bcm958305k.dts @@ -33,6 +33,7 @@ /dts-v1/; #include "bcm-cygnus.dtsi" +#include "bcm9hmidc.dtsi" / { model = "Cygnus Wireless Audio (BCM958305K)"; @@ -43,11 +44,42 @@ }; chosen { - stdout-path = &uart3; - bootargs = "console=ttyS0,115200"; + stdout-path = "serial0:115200n8"; }; +}; + +&i2c0 { + status = "okay"; +}; + +&i2c1 { + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&nand { + nandcs@1 { + compatible = "brcm,nandcs"; + reg = <0>; + nand-on-flash-bbt; + + #address-cells = <1>; + #size-cells = <1>; + + nand-ecc-strength = <24>; + nand-ecc-step-size = <1024>; - uart3: serial@18023000 { - status = "okay"; + brcm,nand-oob-sector-size = <27>; }; }; diff --git a/arch/arm/boot/dts/bcm958625k.dts b/arch/arm/boot/dts/bcm958625k.dts new file mode 100644 index 000000000000..16303dbd35df --- /dev/null +++ b/arch/arm/boot/dts/bcm958625k.dts @@ -0,0 +1,57 @@ +/* + * BSD LICENSE + * + * Copyright(c) 2015 Broadcom Corporation. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name of Broadcom Corporation nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +/dts-v1/; + +#include "bcm-nsp.dtsi" + +/ { + model = "NorthStar Plus SVK (BCM958625K)"; + compatible = "brcm,bcm58625", "brcm,nsp"; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/bcm9hmidc.dtsi b/arch/arm/boot/dts/bcm9hmidc.dtsi new file mode 100644 index 000000000000..65397c088335 --- /dev/null +++ b/arch/arm/boot/dts/bcm9hmidc.dtsi @@ -0,0 +1,42 @@ +/* + * BSD LICENSE + * + * Copyright(c) 2015 Broadcom Corporation. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name of Broadcom Corporation nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +/* + * Broadcom human machine interface daughter card (bcm9hmidc) installed on + * bcm958300k/bcm958305k boards + */ + +&touchscreen { + touchscreen-inverted-x; + touchscreen-inverted-y; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts b/arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts index 5c99fb3a4d10..3c0907b87fd6 100644 --- a/arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts +++ b/arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts @@ -45,7 +45,8 @@ compatible = "sony,nsz-gs7", "marvell,berlin2", "marvell,berlin"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + bootargs = "earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/berlin2.dtsi b/arch/arm/boot/dts/berlin2.dtsi index ef811de09908..eaadac3bdd44 100644 --- a/arch/arm/boot/dts/berlin2.dtsi +++ b/arch/arm/boot/dts/berlin2.dtsi @@ -47,6 +47,12 @@ model = "Marvell Armada 1500 (BG2) SoC"; compatible = "marvell,berlin2", "marvell,berlin"; + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -57,6 +63,16 @@ device_type = "cpu"; next-level-cache = <&l2>; reg = <0>; + + clocks = <&chip_clk CLKID_CPU>; + clock-latency = <100000>; + operating-points = < + /* kHz uV */ + 1200000 1200000 + 1000000 1200000 + 800000 1200000 + 600000 1200000 + >; }; cpu@1 { @@ -404,6 +420,13 @@ }; }; + pwm: pwm@f20000 { + compatible = "marvell,berlin-pwm"; + reg = <0xf20000 0x40>; + clocks = <&chip_clk CLKID_CFG>; + #pwm-cells = <3>; + }; + apb@fc0000 { compatible = "simple-bus"; #address-cells = <1>; diff --git a/arch/arm/boot/dts/berlin2cd-google-chromecast.dts b/arch/arm/boot/dts/berlin2cd-google-chromecast.dts index 772165ad0a52..8ba8b50ce997 100644 --- a/arch/arm/boot/dts/berlin2cd-google-chromecast.dts +++ b/arch/arm/boot/dts/berlin2cd-google-chromecast.dts @@ -46,7 +46,8 @@ compatible = "google,chromecast", "marvell,berlin2cd", "marvell,berlin"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + bootargs = "earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/berlin2cd.dtsi b/arch/arm/boot/dts/berlin2cd.dtsi index 900213d78a32..b16df157214d 100644 --- a/arch/arm/boot/dts/berlin2cd.dtsi +++ b/arch/arm/boot/dts/berlin2cd.dtsi @@ -47,6 +47,11 @@ model = "Marvell Armada 1500-mini (BG2CD) SoC"; compatible = "marvell,berlin2cd", "marvell,berlin"; + aliases { + serial0 = &uart0; + serial1 = &uart1; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -56,6 +61,14 @@ device_type = "cpu"; next-level-cache = <&l2>; reg = <0>; + + clocks = <&chip_clk CLKID_CPU>; + clock-latency = <100000>; + operating-points = < + /* kHz uV */ + 800000 1200000 + 600000 1200000 + >; }; }; @@ -368,6 +381,13 @@ status = "disabled"; }; + pwm: pwm@f20000 { + compatible = "marvell,berlin-pwm"; + reg = <0xf20000 0x40>; + clocks = <&chip_clk CLKID_CFG>; + #pwm-cells = <3>; + }; + apb@fc0000 { compatible = "simple-bus"; #address-cells = <1>; diff --git a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts index 4a749e5b3b44..da28c9704a9d 100644 --- a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts +++ b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts @@ -49,7 +49,8 @@ }; choosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + bootargs = "earlyprintk"; + stdout-path = "serial0:115200n8"; }; regulators { diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/berlin2q.dtsi index d4dbd28d348c..8ea177f375dd 100644 --- a/arch/arm/boot/dts/berlin2q.dtsi +++ b/arch/arm/boot/dts/berlin2q.dtsi @@ -43,6 +43,11 @@ model = "Marvell Armada 1500 pro (BG2-Q) SoC"; compatible = "marvell,berlin2q", "marvell,berlin"; + aliases { + serial0 = &uart0; + serial1 = &uart1; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -53,6 +58,17 @@ device_type = "cpu"; next-level-cache = <&l2>; reg = <0>; + + clocks = <&chip_clk CLKID_CPU>; + clock-latency = <100000>; + /* Can be modified by the bootloader */ + operating-points = < + /* kHz uV */ + 1200000 1200000 + 1000000 1200000 + 800000 1200000 + 600000 1200000 + >; }; cpu@1 { @@ -477,6 +493,13 @@ status = "disabled"; }; + pwm: pwm@f20000 { + compatible = "marvell,berlin-pwm"; + reg = <0xf20000 0x40>; + clocks = <&chip_clk CLKID_CFG>; + #pwm-cells = <3>; + }; + apb@fc0000 { compatible = "simple-bus"; #address-cells = <1>; diff --git a/arch/arm/boot/dts/cx92755.dtsi b/arch/arm/boot/dts/cx92755.dtsi index df4c6f1f93f9..a5a23c376418 100644 --- a/arch/arm/boot/dts/cx92755.dtsi +++ b/arch/arm/boot/dts/cx92755.dtsi @@ -95,6 +95,13 @@ timeout-sec = <15>; }; + pinctrl: pinctrl@f0000e20 { + compatible = "cnxt,cx92755-pinctrl"; + reg = <0xf0000e20 0x100>; + gpio-controller; + #gpio-cells = <2>; + }; + uc_regs: syscon@f00003a0 { compatible = "cnxt,cx92755-uc", "syscon"; reg = <0xf00003a0 0x10>; diff --git a/arch/arm/boot/dts/cx92755_equinox.dts b/arch/arm/boot/dts/cx92755_equinox.dts index 5da00806c41e..026f556c8c50 100644 --- a/arch/arm/boot/dts/cx92755_equinox.dts +++ b/arch/arm/boot/dts/cx92755_equinox.dts @@ -70,8 +70,17 @@ &uart0 { status = "okay"; + pinctrl-0 = <&uart0_default>; + pinctrl-names = "default"; }; &i2c { status = "okay"; }; + +&pinctrl { + uart0_default: uart0_active { + pins = "GP_O0", "GP_O1"; + function = "client_b"; + }; +}; diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi index 179121630ad7..cd58c2e62757 100644 --- a/arch/arm/boot/dts/dove.dtsi +++ b/arch/arm/boot/dts/dove.dtsi @@ -263,12 +263,13 @@ }; crypto: crypto-engine@30000 { - compatible = "marvell,orion-crypto"; - reg = <0x30000 0x10000>, - <0xffffe000 0x800>; - reg-names = "regs", "sram"; + compatible = "marvell,dove-crypto"; + reg = <0x30000 0x10000>; + reg-names = "regs"; interrupts = <31>; clocks = <&gate_clk 15>; + marvell,crypto-srams = <&crypto_sram>; + marvell,crypto-sram-size = <0x800>; status = "okay"; }; @@ -767,6 +768,14 @@ interrupts = <47>; status = "disabled"; }; + + crypto_sram: sa-sram@ffffe000 { + compatible = "mmio-sram"; + reg = <0xffffe000 0x800>; + clocks = <&gate_clk 15>; + #address-cells = <1>; + #size-cells = <1>; + }; }; }; }; diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index a6c82e5b64fe..864f60020124 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -9,6 +9,8 @@ #include "dra74x.dtsi" #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/clk/ti-dra7-atl.h> +#include <dt-bindings/input/input.h> / { model = "TI DRA742"; @@ -28,13 +30,22 @@ gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>; }; - mmc2_3v3: fixedregulator-mmc2 { + evm_3v3_sw: fixedregulator-evm_3v3_sw { compatible = "regulator-fixed"; - regulator-name = "mmc2_3v3"; + regulator-name = "evm_3v3_sw"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; + aic_dvdd: fixedregulator-aic_dvdd { + /* TPS77018DBVT */ + compatible = "regulator-fixed"; + regulator-name = "aic_dvdd"; + vin-supply = <&evm_3v3_sw>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + extcon_usb1: extcon_usb1 { compatible = "linux,extcon-usb-gpio"; id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>; @@ -55,6 +66,86 @@ enable-active-high; gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>; }; + + sound0: sound@0 { + compatible = "simple-audio-card"; + simple-audio-card,name = "DRA7xx-EVM"; + simple-audio-card,widgets = + "Headphone", "Headphone Jack", + "Line", "Line Out", + "Microphone", "Mic Jack", + "Line", "Line In"; + simple-audio-card,routing = + "Headphone Jack", "HPLOUT", + "Headphone Jack", "HPROUT", + "Line Out", "LLOUT", + "Line Out", "RLOUT", + "MIC3L", "Mic Jack", + "MIC3R", "Mic Jack", + "Mic Jack", "Mic Bias", + "LINE1L", "Line In", + "LINE1R", "Line In"; + simple-audio-card,format = "dsp_b"; + simple-audio-card,bitclock-master = <&sound0_master>; + simple-audio-card,frame-master = <&sound0_master>; + simple-audio-card,bitclock-inversion; + + sound0_master: simple-audio-card,cpu { + sound-dai = <&mcasp3>; + system-clock-frequency = <5644800>; + }; + + simple-audio-card,codec { + sound-dai = <&tlv320aic3106>; + clocks = <&atl_clkin2_ck>; + }; + }; + + leds { + compatible = "gpio-leds"; + led@0 { + label = "dra7:usr1"; + gpios = <&pcf_lcd 4 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led@1 { + label = "dra7:usr2"; + gpios = <&pcf_lcd 5 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led@2 { + label = "dra7:usr3"; + gpios = <&pcf_lcd 6 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led@3 { + label = "dra7:usr4"; + gpios = <&pcf_lcd 7 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + autorepeat; + + USER1 { + label = "btnUser1"; + linux,code = <BTN_0>; + gpios = <&pcf_lcd 2 GPIO_ACTIVE_LOW>; + }; + + USER2 { + label = "btnUser2"; + linux,code = <BTN_1>; + gpios = <&pcf_lcd 3 GPIO_ACTIVE_LOW>; + }; + }; }; &dra7_pmx_core { @@ -283,6 +374,31 @@ 0x418 (MUX_MODE15 | PULL_UP) /* wakeup0.off */ >; }; + + atl_pins: pinmux_atl_pins { + pinctrl-single,pins = < + 0x298 (PIN_OUTPUT | MUX_MODE5) /* xref_clk1.atl_clk1 */ + 0x29c (PIN_OUTPUT | MUX_MODE5) /* xref_clk2.atl_clk2 */ + >; + }; + + mcasp3_pins: pinmux_mcasp3_pins { + pinctrl-single,pins = < + 0x324 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx */ + 0x328 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx */ + 0x32c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0 */ + 0x330 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1 */ + >; + }; + + mcasp3_sleep_pins: pinmux_mcasp3_sleep_pins { + pinctrl-single,pins = < + 0x324 (MUX_MODE15) + 0x328 (MUX_MODE15) + 0x32c (MUX_MODE15) + 0x330 (MUX_MODE15) + >; + }; }; &i2c1 { @@ -410,6 +526,17 @@ }; }; + pcf_lcd: gpio@20 { + compatible = "nxp,pcf8575"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + }; + pcf_gpio_21: gpio@21 { compatible = "ti,pcf8575"; reg = <0x21>; @@ -422,6 +549,20 @@ #interrupt-cells = <2>; }; + tlv320aic3106: tlv320aic3106@19 { + #sound-dai-cells = <0>; + compatible = "ti,tlv320aic3106"; + reg = <0x19>; + adc-settle-ms = <40>; + ai3x-micbias-vg = <1>; /* 2.0V */ + status = "okay"; + + /* Regulators */ + AVDD-supply = <&evm_3v3_sw>; + IOVDD-supply = <&evm_3v3_sw>; + DRVDD-supply = <&evm_3v3_sw>; + DVDD-supply = <&aic_dvdd>; + }; }; &i2c2 { @@ -429,6 +570,20 @@ pinctrl-names = "default"; pinctrl-0 = <&i2c2_pins>; clock-frequency = <400000>; + + pcf_hdmi: gpio@26 { + compatible = "nxp,pcf8575"; + reg = <0x26>; + gpio-controller; + #gpio-cells = <2>; + p1 { + /* vin6_sel_s0: high: VIN6, low: audio */ + gpio-hog; + gpios = <1 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "vin6_sel_s0"; + }; + }; }; &i2c3 { @@ -479,12 +634,12 @@ * SDCD signal is not being used here - using the fact that GPIO mode * is always hardwired. */ - cd-gpios = <&gpio6 27 0>; + cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; }; &mmc2 { status = "okay"; - vmmc-supply = <&mmc2_3v3>; + vmmc-supply = <&evm_3v3_sw>; bus-width = <8>; }; @@ -707,3 +862,62 @@ pinctrl-1 = <&dcan1_pins_sleep>; pinctrl-2 = <&dcan1_pins_default>; }; + +&atl { + pinctrl-names = "default"; + pinctrl-0 = <&atl_pins>; + + assigned-clocks = <&abe_dpll_sys_clk_mux>, + <&atl_gfclk_mux>, + <&dpll_abe_ck>, + <&dpll_abe_m2x2_ck>, + <&atl_clkin2_ck>; + assigned-clock-parents = <&sys_clkin2>, <&dpll_abe_m2_ck>; + assigned-clock-rates = <0>, <0>, <180633600>, <361267200>, <5644800>; + + status = "okay"; + + atl2 { + bws = <DRA7_ATL_WS_MCASP2_FSX>; + aws = <DRA7_ATL_WS_MCASP3_FSX>; + }; +}; + +&mcasp3 { + #sound-dai-cells = <0>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mcasp3_pins>; + pinctrl-1 = <&mcasp3_sleep_pins>; + + assigned-clocks = <&mcasp3_ahclkx_mux>; + assigned-clock-parents = <&atl_clkin2_ck>; + + status = "okay"; + + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + /* 4 serializer */ + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 1 2 0 0 + >; +}; + +&mailbox5 { + status = "okay"; + mbox_ipu1_ipc3x: mbox_ipu1_ipc3x { + status = "okay"; + }; + mbox_dsp1_ipc3x: mbox_dsp1_ipc3x { + status = "okay"; + }; +}; + +&mailbox6 { + status = "okay"; + mbox_ipu2_ipc3x: mbox_ipu2_ipc3x { + status = "okay"; + }; + mbox_dsp2_ipc3x: mbox_dsp2_ipc3x { + status = "okay"; + }; +}; diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index 8fedddc35999..bc672fb91466 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -292,6 +292,11 @@ #thermal-sensor-cells = <1>; }; + dsp1_system: dsp_system@40d00000 { + compatible = "syscon"; + reg = <0x40d00000 0x100>; + }; + sdma: dma-controller@4a056000 { compatible = "ti,omap4430-sdma"; reg = <0x4a056000 0x1000>; @@ -911,6 +916,46 @@ status = "disabled"; }; + mmu0_dsp1: mmu@40d01000 { + compatible = "ti,dra7-dsp-iommu"; + reg = <0x40d01000 0x100>; + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmu0_dsp1"; + #iommu-cells = <0>; + ti,syscon-mmuconfig = <&dsp1_system 0x0>; + status = "disabled"; + }; + + mmu1_dsp1: mmu@40d02000 { + compatible = "ti,dra7-dsp-iommu"; + reg = <0x40d02000 0x100>; + interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmu1_dsp1"; + #iommu-cells = <0>; + ti,syscon-mmuconfig = <&dsp1_system 0x1>; + status = "disabled"; + }; + + mmu_ipu1: mmu@58882000 { + compatible = "ti,dra7-iommu"; + reg = <0x58882000 0x100>; + interrupts = <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmu_ipu1"; + #iommu-cells = <0>; + ti,iommu-bus-err-back; + status = "disabled"; + }; + + mmu_ipu2: mmu@55082000 { + compatible = "ti,dra7-iommu"; + reg = <0x55082000 0x100>; + interrupts = <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmu_ipu2"; + #iommu-cells = <0>; + ti,iommu-bus-err-back; + status = "disabled"; + }; + abb_mpu: regulator-abb-mpu { compatible = "ti,abb-v3"; regulator-name = "abb_mpu"; @@ -1404,6 +1449,21 @@ status = "disabled"; }; + mcasp3: mcasp@48468000 { + compatible = "ti,dra7-mcasp-audio"; + ti,hwmods = "mcasp3"; + reg = <0x48468000 0x2000>; + reg-names = "mpu"; + interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tx", "rx"; + dmas = <&sdma_xbar 133>, <&sdma_xbar 132>; + dma-names = "tx", "rx"; + clocks = <&mcasp3_ahclkx_mux>; + clock-names = "fck"; + status = "disabled"; + }; + crossbar_mpu: crossbar@4a002a48 { compatible = "ti,irq-crossbar"; reg = <0x4a002a48 0x130>; diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts index 6f6bd98c98df..d6104d5f0c01 100644 --- a/arch/arm/boot/dts/dra72-evm.dts +++ b/arch/arm/boot/dts/dra72-evm.dts @@ -9,6 +9,7 @@ #include "dra72x.dtsi" #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/clk/ti-dra7-atl.h> / { model = "TI DRA722"; @@ -30,6 +31,15 @@ regulator-max-microvolt = <3300000>; }; + aic_dvdd: fixedregulator-aic_dvdd { + /* TPS77018DBVT */ + compatible = "regulator-fixed"; + regulator-name = "aic_dvdd"; + vin-supply = <&evm_3v3>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + evm_3v3_sd: fixedregulator-sd { compatible = "regulator-fixed"; regulator-name = "evm_3v3_sd"; @@ -93,6 +103,40 @@ }; }; }; + + sound0: sound@0 { + compatible = "simple-audio-card"; + simple-audio-card,name = "DRA7xx-EVM"; + simple-audio-card,widgets = + "Headphone", "Headphone Jack", + "Line", "Line Out", + "Microphone", "Mic Jack", + "Line", "Line In"; + simple-audio-card,routing = + "Headphone Jack", "HPLOUT", + "Headphone Jack", "HPROUT", + "Line Out", "LLOUT", + "Line Out", "RLOUT", + "MIC3L", "Mic Jack", + "MIC3R", "Mic Jack", + "Mic Jack", "Mic Bias", + "LINE1L", "Line In", + "LINE1R", "Line In"; + simple-audio-card,format = "dsp_b"; + simple-audio-card,bitclock-master = <&sound0_master>; + simple-audio-card,frame-master = <&sound0_master>; + simple-audio-card,bitclock-inversion; + + sound0_master: simple-audio-card,cpu { + sound-dai = <&mcasp3>; + system-clock-frequency = <5644800>; + }; + + simple-audio-card,codec { + sound-dai = <&tlv320aic3106>; + clocks = <&atl_clkin2_ck>; + }; + }; }; &dra7_pmx_core { @@ -110,6 +154,13 @@ >; }; + i2c5_pins: pinmux_i2c5_pins { + pinctrl-single,pins = < + 0x2b4 (PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */ + 0x2b8 (PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ + >; + }; + nand_default: nand_default { pinctrl-single,pins = < 0x0 (PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */ @@ -220,6 +271,31 @@ 0x3b8 (PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */ >; }; + + atl_pins: pinmux_atl_pins { + pinctrl-single,pins = < + 0x298 (PIN_OUTPUT | MUX_MODE5) /* xref_clk1.atl_clk1 */ + 0x29c (PIN_OUTPUT | MUX_MODE5) /* xref_clk2.atl_clk2 */ + >; + }; + + mcasp3_pins: pinmux_mcasp3_pins { + pinctrl-single,pins = < + 0x324 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx */ + 0x328 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx */ + 0x32c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0 */ + 0x330 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1 */ + >; + }; + + mcasp3_sleep_pins: pinmux_mcasp3_sleep_pins { + pinctrl-single,pins = < + 0x324 (PIN_INPUT_PULLDOWN | MUX_MODE15) + 0x328 (PIN_INPUT_PULLDOWN | MUX_MODE15) + 0x32c (PIN_INPUT_PULLDOWN | MUX_MODE15) + 0x330 (PIN_INPUT_PULLDOWN | MUX_MODE15) + >; + }; }; &i2c1 { @@ -353,12 +429,21 @@ interrupts = <11 IRQ_TYPE_EDGE_FALLING>; interrupt-controller; #interrupt-cells = <2>; + }; - cpsw_sel_s0 { - gpio-hog; - gpios = <4 GPIO_ACTIVE_HIGH>; - output-low; - }; + tlv320aic3106: tlv320aic3106@19 { + #sound-dai-cells = <0>; + compatible = "ti,tlv320aic3106"; + reg = <0x19>; + adc-settle-ms = <40>; + ai3x-micbias-vg = <1>; /* 2.0V */ + status = "okay"; + + /* Regulators */ + AVDD-supply = <&evm_3v3>; + IOVDD-supply = <&evm_3v3>; + DRVDD-supply = <&evm_3v3>; + DVDD-supply = <&aic_dvdd>; }; }; @@ -380,6 +465,14 @@ * VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6 */ lines-initial-states = <0x0f2b>; + + p1 { + /* vin6_sel_s0: high: VIN6, low: audio */ + gpio-hog; + gpios = <1 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "vin6_sel_s0"; + }; }; }; @@ -514,7 +607,7 @@ * SDCD signal is not being used here - using the fact that GPIO mode * is a viable alternative */ - cd-gpios = <&gpio6 27 0>; + cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; max-frequency = <192000000>; }; @@ -590,6 +683,7 @@ pinctrl-0 = <&cpsw_default>; pinctrl-1 = <&cpsw_sleep>; slaves = <1>; + mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_HIGH>; }; &cpsw_emac0 { @@ -695,3 +789,59 @@ }; }; }; + +&atl { + pinctrl-names = "default"; + pinctrl-0 = <&atl_pins>; + + assigned-clocks = <&abe_dpll_sys_clk_mux>, + <&atl_gfclk_mux>, + <&dpll_abe_ck>, + <&dpll_abe_m2x2_ck>, + <&atl_clkin2_ck>; + assigned-clock-parents = <&sys_clkin2>, <&dpll_abe_m2_ck>; + assigned-clock-rates = <0>, <0>, <180633600>, <361267200>, <5644800>; + + status = "okay"; + + atl2 { + bws = <DRA7_ATL_WS_MCASP2_FSX>; + aws = <DRA7_ATL_WS_MCASP3_FSX>; + }; +}; + +&mcasp3 { + #sound-dai-cells = <0>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mcasp3_pins>; + pinctrl-1 = <&mcasp3_sleep_pins>; + + assigned-clocks = <&mcasp3_ahclkx_mux>; + assigned-clock-parents = <&atl_clkin2_ck>; + + status = "okay"; + + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + /* 4 serializer */ + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 1 2 0 0 + >; +}; + +&mailbox5 { + status = "okay"; + mbox_ipu1_ipc3x: mbox_ipu1_ipc3x { + status = "okay"; + }; + mbox_dsp1_ipc3x: mbox_dsp1_ipc3x { + status = "okay"; + }; +}; + +&mailbox6 { + status = "okay"; + mbox_ipu2_ipc3x: mbox_ipu2_ipc3x { + status = "okay"; + }; +}; diff --git a/arch/arm/boot/dts/dra72x.dtsi b/arch/arm/boot/dts/dra72x.dtsi index eaca143faa77..70a217050a4c 100644 --- a/arch/arm/boot/dts/dra72x.dtsi +++ b/arch/arm/boot/dts/dra72x.dtsi @@ -45,3 +45,24 @@ <&dss_video1_clk>; clock-names = "fck", "video1_clk"; }; + +&mailbox5 { + mbox_ipu1_ipc3x: mbox_ipu1_ipc3x { + ti,mbox-tx = <6 2 2>; + ti,mbox-rx = <4 2 2>; + status = "disabled"; + }; + mbox_dsp1_ipc3x: mbox_dsp1_ipc3x { + ti,mbox-tx = <5 2 2>; + ti,mbox-rx = <1 2 2>; + status = "disabled"; + }; +}; + +&mailbox6 { + mbox_ipu2_ipc3x: mbox_ipu2_ipc3x { + ti,mbox-tx = <6 2 2>; + ti,mbox-rx = <4 2 2>; + status = "disabled"; + }; +}; diff --git a/arch/arm/boot/dts/dra74x.dtsi b/arch/arm/boot/dts/dra74x.dtsi index feea98e0a4b5..8bcc47db1cd1 100644 --- a/arch/arm/boot/dts/dra74x.dtsi +++ b/arch/arm/boot/dts/dra74x.dtsi @@ -52,6 +52,11 @@ }; ocp { + dsp2_system: dsp_system@41500000 { + compatible = "syscon"; + reg = <0x41500000 0x100>; + }; + omap_dwc3_4: omap_dwc3_4@48940000 { compatible = "ti,dwc3"; ti,hwmods = "usb_otg_ss4"; @@ -76,6 +81,26 @@ dr_mode = "otg"; }; }; + + mmu0_dsp2: mmu@41501000 { + compatible = "ti,dra7-dsp-iommu"; + reg = <0x41501000 0x100>; + interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmu0_dsp2"; + #iommu-cells = <0>; + ti,syscon-mmuconfig = <&dsp2_system 0x0>; + status = "disabled"; + }; + + mmu1_dsp2: mmu@41502000 { + compatible = "ti,dra7-dsp-iommu"; + reg = <0x41502000 0x100>; + interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmu1_dsp2"; + #iommu-cells = <0>; + ti,syscon-mmuconfig = <&dsp2_system 0x1>; + status = "disabled"; + }; }; }; @@ -93,3 +118,29 @@ <&dss_video2_clk>; clock-names = "fck", "video1_clk", "video2_clk"; }; + +&mailbox5 { + mbox_ipu1_ipc3x: mbox_ipu1_ipc3x { + ti,mbox-tx = <6 2 2>; + ti,mbox-rx = <4 2 2>; + status = "disabled"; + }; + mbox_dsp1_ipc3x: mbox_dsp1_ipc3x { + ti,mbox-tx = <5 2 2>; + ti,mbox-rx = <1 2 2>; + status = "disabled"; + }; +}; + +&mailbox6 { + mbox_ipu2_ipc3x: mbox_ipu2_ipc3x { + ti,mbox-tx = <6 2 2>; + ti,mbox-rx = <4 2 2>; + status = "disabled"; + }; + mbox_dsp2_ipc3x: mbox_dsp2_ipc3x { + ti,mbox-tx = <5 2 2>; + ti,mbox-rx = <1 2 2>; + status = "disabled"; + }; +}; diff --git a/arch/arm/boot/dts/exynos3250-monk.dts b/arch/arm/boot/dts/exynos3250-monk.dts index 540a0adf2be6..443a35085846 100644 --- a/arch/arm/boot/dts/exynos3250-monk.dts +++ b/arch/arm/boot/dts/exynos3250-monk.dts @@ -52,13 +52,13 @@ regulator-name = "V_EMMC_2.8V-fixed"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpk0 2 0>; + gpio = <&gpk0 2 GPIO_ACTIVE_HIGH>; enable-active-high; }; i2c_max77836: i2c-gpio-0 { compatible = "i2c-gpio"; - gpios = <&gpd0 2 0>, <&gpd0 3 0>; + gpios = <&gpd0 2 GPIO_ACTIVE_HIGH>, <&gpd0 3 GPIO_ACTIVE_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -161,6 +161,7 @@ }; &exynos_usbphy { + vbus-supply = <&safeout_reg>; status = "okay"; }; @@ -266,14 +267,14 @@ regulator-name = "V_EMMC_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - samsung,ext-control-gpios = <&gpk0 2 0>; + samsung,ext-control-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; }; ldo12_reg: LDO12 { regulator-name = "V_EMMC_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - samsung,ext-control-gpios = <&gpk0 2 0>; + samsung,ext-control-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; }; ldo13_reg: LDO13 { diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts index 41a5fafb9aa9..3e64d5dcdd60 100644 --- a/arch/arm/boot/dts/exynos3250-rinato.dts +++ b/arch/arm/boot/dts/exynos3250-rinato.dts @@ -49,7 +49,7 @@ i2c_max77836: i2c-gpio-0 { compatible = "i2c-gpio"; - gpios = <&gpd0 2 0>, <&gpd0 3 0>; + gpios = <&gpd0 2 GPIO_ACTIVE_HIGH>, <&gpd0 3 GPIO_ACTIVE_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -153,6 +153,7 @@ &exynos_usbphy { status = "okay"; + vbus-supply = <&safeout_reg>; }; &hsotg { @@ -188,8 +189,8 @@ reg = <0>; vdd3-supply = <&ldo16_reg>; vci-supply = <&ldo20_reg>; - reset-gpios = <&gpe0 1 0>; - te-gpios = <&gpx0 6 0>; + reset-gpios = <&gpe0 1 GPIO_ACTIVE_HIGH>; + te-gpios = <&gpx0 6 GPIO_ACTIVE_HIGH>; power-on-delay= <30>; power-off-delay= <120>; reset-delay = <5>; @@ -368,14 +369,14 @@ regulator-name = "V_EMMC_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - samsung,ext-control-gpios = <&gpk0 2 0>; + samsung,ext-control-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; }; ldo12_reg: LDO12 { regulator-name = "V_EMMC_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - samsung,ext-control-gpios = <&gpk0 2 0>; + samsung,ext-control-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; }; ldo13_reg: LDO13 { diff --git a/arch/arm/boot/dts/exynos3250.dtsi b/arch/arm/boot/dts/exynos3250.dtsi index 033def482fc3..2f30d632f1cc 100644 --- a/arch/arm/boot/dts/exynos3250.dtsi +++ b/arch/arm/boot/dts/exynos3250.dtsi @@ -333,7 +333,7 @@ }; mshc_0: mshc@12510000 { - compatible = "samsung,exynos5250-dw-mshc"; + compatible = "samsung,exynos5420-dw-mshc"; reg = <0x12510000 0x1000>; interrupts = <0 142 0>; clocks = <&cmu CLK_SDMMC0>, <&cmu CLK_SCLK_MMC0>; @@ -345,7 +345,7 @@ }; mshc_1: mshc@12520000 { - compatible = "samsung,exynos5250-dw-mshc"; + compatible = "samsung,exynos5420-dw-mshc"; reg = <0x12520000 0x1000>; interrupts = <0 143 0>; clocks = <&cmu CLK_SDMMC1>, <&cmu CLK_SCLK_MMC1>; diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi index 98c0a368b777..3184e10f260a 100644 --- a/arch/arm/boot/dts/exynos4.dtsi +++ b/arch/arm/boot/dts/exynos4.dtsi @@ -431,6 +431,8 @@ interrupts = <0 52 0>; clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>; clock-names = "uart", "clk_uart_baud0"; + dmas = <&pdma0 15>, <&pdma0 16>; + dma-names = "rx", "tx"; status = "disabled"; }; @@ -440,6 +442,8 @@ interrupts = <0 53 0>; clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>; clock-names = "uart", "clk_uart_baud0"; + dmas = <&pdma1 15>, <&pdma1 16>; + dma-names = "rx", "tx"; status = "disabled"; }; @@ -449,6 +453,8 @@ interrupts = <0 54 0>; clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; clock-names = "uart", "clk_uart_baud0"; + dmas = <&pdma0 17>, <&pdma0 18>; + dma-names = "rx", "tx"; status = "disabled"; }; @@ -458,6 +464,8 @@ interrupts = <0 55 0>; clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>; clock-names = "uart", "clk_uart_baud0"; + dmas = <&pdma1 17>, <&pdma1 18>; + dma-names = "rx", "tx"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts index e050d85cdacd..b8f866991bdd 100644 --- a/arch/arm/boot/dts/exynos4210-origen.dts +++ b/arch/arm/boot/dts/exynos4210-origen.dts @@ -16,6 +16,7 @@ /dts-v1/; #include "exynos4210.dtsi" +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> / { @@ -45,7 +46,7 @@ regulator-name = "VMEM_VDD_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpx1 1 0>; + gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>; enable-active-high; }; }; @@ -57,35 +58,35 @@ up { label = "Up"; - gpios = <&gpx2 0 1>; + gpios = <&gpx2 0 GPIO_ACTIVE_LOW>; linux,code = <KEY_UP>; gpio-key,wakeup; }; down { label = "Down"; - gpios = <&gpx2 1 1>; + gpios = <&gpx2 1 GPIO_ACTIVE_LOW>; linux,code = <KEY_DOWN>; gpio-key,wakeup; }; back { label = "Back"; - gpios = <&gpx1 7 1>; + gpios = <&gpx1 7 GPIO_ACTIVE_LOW>; linux,code = <KEY_BACK>; gpio-key,wakeup; }; home { label = "Home"; - gpios = <&gpx1 6 1>; + gpios = <&gpx1 6 GPIO_ACTIVE_LOW>; linux,code = <KEY_HOME>; gpio-key,wakeup; }; menu { label = "Menu"; - gpios = <&gpx1 5 1>; + gpios = <&gpx1 5 GPIO_ACTIVE_LOW>; linux,code = <KEY_MENU>; gpio-key,wakeup; }; @@ -94,7 +95,7 @@ leds { compatible = "gpio-leds"; status { - gpios = <&gpx1 3 1>; + gpios = <&gpx1 3 GPIO_ACTIVE_LOW>; linux,default-trigger = "heartbeat"; }; }; diff --git a/arch/arm/boot/dts/exynos4210-smdkv310.dts b/arch/arm/boot/dts/exynos4210-smdkv310.dts index 043b03caff8f..bc1448ba95d3 100644 --- a/arch/arm/boot/dts/exynos4210-smdkv310.dts +++ b/arch/arm/boot/dts/exynos4210-smdkv310.dts @@ -16,6 +16,7 @@ /dts-v1/; #include "exynos4210.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Samsung smdkv310 evaluation board based on Exynos4210"; @@ -182,7 +183,7 @@ }; &spi_2 { - cs-gpios = <&gpc1 2 0>; + cs-gpios = <&gpc1 2 GPIO_ACTIVE_HIGH>; status = "okay"; w25x80@0 { diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts index ba34886f8b65..a50be640f1b0 100644 --- a/arch/arm/boot/dts/exynos4210-trats.dts +++ b/arch/arm/boot/dts/exynos4210-trats.dts @@ -14,6 +14,7 @@ /dts-v1/; #include "exynos4210.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Samsung Trats based on Exynos4210"; @@ -39,7 +40,7 @@ regulator-name = "VMEM_VDD_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpk0 2 0>; + gpio = <&gpk0 2 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -48,7 +49,7 @@ regulator-name = "TSP_FIXED_VOLTAGES"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpl0 3 0>; + gpio = <&gpl0 3 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -57,7 +58,7 @@ regulator-name = "8M_AF_2.8V_EN"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpk1 1 0>; + gpio = <&gpk1 1 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -66,7 +67,7 @@ regulator-name = "CAM_IO_EN"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpe2 1 0>; + gpio = <&gpe2 1 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -75,7 +76,7 @@ regulator-name = "8M_1.2V_EN"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; - gpio = <&gpe2 5 0>; + gpio = <&gpe2 5 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -84,7 +85,7 @@ regulator-name = "VT_CORE_1.5V"; regulator-min-microvolt = <1500000>; regulator-max-microvolt = <1500000>; - gpio = <&gpe2 2 0>; + gpio = <&gpe2 2 GPIO_ACTIVE_HIGH>; enable-active-high; }; }; @@ -93,21 +94,21 @@ compatible = "gpio-keys"; vol-down-key { - gpios = <&gpx2 1 1>; + gpios = <&gpx2 1 GPIO_ACTIVE_LOW>; linux,code = <114>; label = "volume down"; debounce-interval = <10>; }; vol-up-key { - gpios = <&gpx2 0 1>; + gpios = <&gpx2 0 GPIO_ACTIVE_LOW>; linux,code = <115>; label = "volume up"; debounce-interval = <10>; }; power-key { - gpios = <&gpx2 7 1>; + gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; linux,code = <116>; label = "power"; debounce-interval = <10>; @@ -115,7 +116,7 @@ }; ok-key { - gpios = <&gpx3 5 1>; + gpios = <&gpx3 5 GPIO_ACTIVE_LOW>; linux,code = <352>; label = "ok"; debounce-interval = <10>; @@ -218,7 +219,7 @@ compatible = "samsung,s6e8aa0"; vdd3-supply = <&vcclcd_reg>; vci-supply = <&vlcd_reg>; - reset-gpios = <&gpy4 5 0>; + reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>; power-on-delay= <50>; reset-delay = <100>; init-delay = <100>; @@ -251,6 +252,7 @@ &exynos_usbphy { status = "okay"; + vbus-supply = <&safe1_sreg>; }; &fimd { @@ -304,9 +306,9 @@ max8997,pmic-ignore-gpiodvs-side-effect; max8997,pmic-buck125-default-dvs-idx = <0>; - max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>, - <&gpx0 6 0>, - <&gpl0 0 0>; + max8997,pmic-buck125-dvs-gpios = <&gpx0 5 GPIO_ACTIVE_HIGH>, + <&gpx0 6 GPIO_ACTIVE_HIGH>, + <&gpl0 0 GPIO_ACTIVE_HIGH>; max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>, <1250000>, <1200000>, @@ -448,7 +450,6 @@ safe1_sreg: ESAFEOUT1 { regulator-name = "SAFEOUT1"; - regulator-always-on; }; safe2_sreg: ESAFEOUT2 { diff --git a/arch/arm/boot/dts/exynos4210-universal_c210.dts b/arch/arm/boot/dts/exynos4210-universal_c210.dts index eb379526e234..81b7ec7b3e31 100644 --- a/arch/arm/boot/dts/exynos4210-universal_c210.dts +++ b/arch/arm/boot/dts/exynos4210-universal_c210.dts @@ -14,6 +14,7 @@ /dts-v1/; #include "exynos4210.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Samsung Universal C210 based on Exynos4210 rev0"; @@ -65,7 +66,7 @@ regulator-name = "VMEM_VDD_2_8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpe1 3 0>; + gpio = <&gpe1 3 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -73,21 +74,21 @@ compatible = "gpio-keys"; vol-up-key { - gpios = <&gpx2 0 1>; + gpios = <&gpx2 0 GPIO_ACTIVE_LOW>; linux,code = <115>; label = "volume up"; debounce-interval = <1>; }; vol-down-key { - gpios = <&gpx2 1 1>; + gpios = <&gpx2 1 GPIO_ACTIVE_LOW>; linux,code = <114>; label = "volume down"; debounce-interval = <1>; }; config-key { - gpios = <&gpx2 2 1>; + gpios = <&gpx2 2 GPIO_ACTIVE_LOW>; linux,code = <171>; label = "config"; debounce-interval = <1>; @@ -95,14 +96,14 @@ }; camera-key { - gpios = <&gpx2 3 1>; + gpios = <&gpx2 3 GPIO_ACTIVE_LOW>; linux,code = <212>; label = "camera"; debounce-interval = <1>; }; power-key { - gpios = <&gpx2 7 1>; + gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; linux,code = <116>; label = "power"; debounce-interval = <1>; @@ -110,7 +111,7 @@ }; ok-key { - gpios = <&gpx3 5 1>; + gpios = <&gpx3 5 GPIO_ACTIVE_LOW>; linux,code = <352>; label = "ok"; debounce-interval = <1>; @@ -122,7 +123,7 @@ regulator-name = "TSP_2_8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpe2 3 0>; + gpio = <&gpe2 3 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -131,17 +132,17 @@ #address-cells = <1>; #size-cells = <0>; - gpio-sck = <&gpy3 1 0>; - gpio-mosi = <&gpy3 3 0>; + gpio-sck = <&gpy3 1 GPIO_ACTIVE_HIGH>; + gpio-mosi = <&gpy3 3 GPIO_ACTIVE_HIGH>; num-chipselects = <1>; - cs-gpios = <&gpy4 3 0>; + cs-gpios = <&gpy4 3 GPIO_ACTIVE_HIGH>; lcd@0 { compatible = "samsung,ld9040"; reg = <0>; vdd3-supply = <&ldo7_reg>; vci-supply = <&ldo17_reg>; - reset-gpios = <&gpy4 5 0>; + reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>; spi-max-frequency = <1200000>; spi-cpol; spi-cpha; @@ -218,13 +219,13 @@ regulator-name = "HDMI_5V"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - gpio = <&gpe0 1 0>; + gpio = <&gpe0 1 GPIO_ACTIVE_HIGH>; enable-active-high; }; hdmi_ddc: i2c-ddc { compatible = "i2c-gpio"; - gpios = <&gpe4 2 0 &gpe4 3 0>; + gpios = <&gpe4 2 GPIO_ACTIVE_HIGH &gpe4 3 GPIO_ACTIVE_HIGH>; i2c-gpio,delay-us = <100>; #address-cells = <1>; #size-cells = <0>; @@ -248,6 +249,7 @@ &exynos_usbphy { status = "okay"; + vbus-supply = <&safeout1_reg>; }; &fimd { @@ -267,7 +269,7 @@ }; &hdmi { - hpd-gpio = <&gpx3 7 0>; + hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&hdmi_hpd>; hdmi-en-supply = <&hdmi_en>; @@ -311,7 +313,8 @@ compatible = "maxim,max8952"; reg = <0x60>; - max8952,vid-gpios = <&gpx0 3 0>, <&gpx0 4 0>; + max8952,vid-gpios = <&gpx0 3 GPIO_ACTIVE_HIGH>, + <&gpx0 4 GPIO_ACTIVE_HIGH>; max8952,default-mode = <0>; max8952,dvs-mode-microvolt = <1250000>, <1200000>, <1050000>, <950000>; @@ -330,13 +333,13 @@ reg = <0x66>; max8998,pmic-buck1-default-dvs-idx = <0>; - max8998,pmic-buck1-dvs-gpios = <&gpx0 5 0>, - <&gpx0 6 0>; + max8998,pmic-buck1-dvs-gpios = <&gpx0 5 GPIO_ACTIVE_HIGH>, + <&gpx0 6 GPIO_ACTIVE_HIGH>; max8998,pmic-buck1-dvs-voltage = <1100000>, <1000000>, <1100000>, <1000000>; max8998,pmic-buck2-default-dvs-idx = <0>; - max8998,pmic-buck2-dvs-gpio = <&gpe2 0 0>; + max8998,pmic-buck2-dvs-gpio = <&gpe2 0 GPIO_ACTIVE_HIGH>; max8998,pmic-buck2-dvs-voltage = <1200000>, <1100000>; regulators { @@ -486,7 +489,6 @@ safeout1_reg: ESAFEOUT1 { regulator-name = "SAFEOUT1"; - regulator-always-on; }; safeout2_reg: ESAFEOUT2 { @@ -551,7 +553,7 @@ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>; pinctrl-names = "default"; vmmc-supply = <&ldo5_reg>; - cd-gpios = <&gpx3 4 0>; + cd-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>; cd-inverted; status = "okay"; }; diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi index db52841297a5..edf0fc8db6ff 100644 --- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi +++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi @@ -11,6 +11,7 @@ #include <dt-bindings/input/input.h> #include <dt-bindings/clock/maxim,max77686.h> #include "exynos4412.dtsi" +#include <dt-bindings/gpio/gpio.h> / { chosen { @@ -30,7 +31,7 @@ power_key { interrupt-parent = <&gpx1>; interrupts = <3 0>; - gpios = <&gpx1 3 1>; + gpios = <&gpx1 3 GPIO_ACTIVE_LOW>; linux,code = <KEY_POWER>; label = "power key"; debounce-interval = <10>; @@ -70,7 +71,7 @@ pinctrl-0 = <&sd1_cd>; pinctrl-names = "default"; compatible = "mmc-pwrseq-emmc"; - reset-gpios = <&gpk1 2 1>; + reset-gpios = <&gpk1 2 GPIO_ACTIVE_LOW>; }; camera { @@ -181,7 +182,7 @@ }; &hdmi { - hpd-gpio = <&gpx3 7 0>; + hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&hdmi_hpd>; vdd-supply = <&ldo8_reg>; @@ -199,8 +200,6 @@ }; &i2c_0 { - pinctrl-0 = <&i2c0_bus>; - pinctrl-names = "default"; samsung,i2c-sda-delay = <100>; samsung,i2c-max-bus-freq = <400000>; status = "okay"; @@ -209,9 +208,9 @@ compatible = "smsc,usb3503"; reg = <0x08>; - intn-gpios = <&gpx3 0 0>; - connect-gpios = <&gpx3 4 0>; - reset-gpios = <&gpx3 5 0>; + intn-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>; + connect-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpx3 5 GPIO_ACTIVE_HIGH>; initial-mode = <1>; }; @@ -276,15 +275,13 @@ regulator-always-on; }; - ldo8_reg: ldo@8 { - regulator-compatible = "LDO8"; + ldo8_reg: LDO8 { regulator-name = "VDD10_HDMI_1.0V"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; }; - ldo10_reg: ldo@10 { - regulator-compatible = "LDO10"; + ldo10_reg: LDO10 { regulator-name = "VDDQ_MIPIHSI_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -424,8 +421,6 @@ }; &i2c_1 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_bus>; status = "okay"; max98090: max98090@10 { compatible = "maxim,max98090"; @@ -440,8 +435,6 @@ &i2c_2 { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c2_bus>; }; &i2c_8 { @@ -490,7 +483,7 @@ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; pinctrl-names = "default"; vmmc-supply = <&ldo4_reg &ldo21_reg>; - cd-gpios = <&gpk2 2 0>; + cd-gpios = <&gpk2 2 GPIO_ACTIVE_HIGH>; cd-inverted; status = "okay"; }; diff --git a/arch/arm/boot/dts/exynos4412-odroidu3.dts b/arch/arm/boot/dts/exynos4412-odroidu3.dts index 8632f35c6c26..646ff0bd001a 100644 --- a/arch/arm/boot/dts/exynos4412-odroidu3.dts +++ b/arch/arm/boot/dts/exynos4412-odroidu3.dts @@ -27,11 +27,54 @@ compatible = "gpio-leds"; led1 { label = "led1:heart"; - gpios = <&gpc1 0 1>; + gpios = <&gpc1 0 GPIO_ACTIVE_LOW>; default-state = "on"; linux,default-trigger = "heartbeat"; }; }; + + fan0: pwm-fan { + compatible = "pwm-fan"; + pwms = <&pwm 0 10000 0>; + cooling-min-state = <0>; + cooling-max-state = <3>; + #cooling-cells = <2>; + cooling-levels = <0 102 170 230>; + }; + + thermal-zones { + cpu_thermal: cpu-thermal { + cooling-maps { + map0 { + trip = <&cpu_alert1>; + cooling-device = <&cpu0 7 7>; + }; + map1 { + trip = <&cpu_alert2>; + cooling-device = <&cpu0 13 13>; + }; + map2 { + trip = <&cpu_alert0>; + cooling-device = <&fan0 0 1>; + }; + map3 { + trip = <&cpu_alert1>; + cooling-device = <&fan0 1 2>; + }; + map4 { + trip = <&cpu_alert2>; + cooling-device = <&fan0 2 3>; + }; + }; + }; + }; +}; + +&pwm { + pinctrl-0 = <&pwm0_out>; + pinctrl-names = "default"; + samsung,pwm-outputs = <0>; + status = "okay"; }; &usb3503 { diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts index 679ac103ebf6..b44bb682e976 100644 --- a/arch/arm/boot/dts/exynos4412-odroidx.dts +++ b/arch/arm/boot/dts/exynos4412-odroidx.dts @@ -26,13 +26,13 @@ compatible = "gpio-leds"; led1 { label = "led1:heart"; - gpios = <&gpc1 0 1>; + gpios = <&gpc1 0 GPIO_ACTIVE_LOW>; default-state = "on"; linux,default-trigger = "heartbeat"; }; led2 { label = "led2:mmc0"; - gpios = <&gpc1 2 1>; + gpios = <&gpc1 2 GPIO_ACTIVE_LOW>; default-state = "on"; linux,default-trigger = "mmc0"; }; @@ -44,7 +44,7 @@ home_key { interrupt-parent = <&gpx2>; interrupts = <2 0>; - gpios = <&gpx2 2 0>; + gpios = <&gpx2 2 GPIO_ACTIVE_HIGH>; linux,code = <KEY_HOME>; label = "home key"; debounce-interval = <10>; @@ -57,7 +57,7 @@ regulator-name = "p3v3_en"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - gpio = <&gpa1 1 1>; + gpio = <&gpa1 1 GPIO_ACTIVE_LOW>; enable-active-high; regulator-always-on; }; diff --git a/arch/arm/boot/dts/exynos4412-origen.dts b/arch/arm/boot/dts/exynos4412-origen.dts index 9d528af68c1a..c8d86af2fb98 100644 --- a/arch/arm/boot/dts/exynos4412-origen.dts +++ b/arch/arm/boot/dts/exynos4412-origen.dts @@ -14,6 +14,7 @@ /dts-v1/; #include "exynos4412.dtsi" +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> / { @@ -45,7 +46,7 @@ regulator-name = "VMEM_VDD_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpx1 1 0>; + gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>; enable-active-high; }; }; @@ -107,13 +108,13 @@ s5m8767,pmic-buck-default-dvs-idx = <3>; - s5m8767,pmic-buck-dvs-gpios = <&gpx2 3 0>, - <&gpx2 4 0>, - <&gpx2 5 0>; + s5m8767,pmic-buck-dvs-gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>, + <&gpx2 4 GPIO_ACTIVE_HIGH>, + <&gpx2 5 GPIO_ACTIVE_HIGH>; - s5m8767,pmic-buck-ds-gpios = <&gpm3 5 0>, - <&gpm3 6 0>, - <&gpm3 7 0>; + s5m8767,pmic-buck-ds-gpios = <&gpm3 5 GPIO_ACTIVE_HIGH>, + <&gpm3 6 GPIO_ACTIVE_HIGH>, + <&gpm3 7 GPIO_ACTIVE_HIGH>; s5m8767,pmic-buck2-dvs-voltage = <1250000>, <1200000>, <1200000>, <1200000>, diff --git a/arch/arm/boot/dts/exynos4412-tiny4412.dts b/arch/arm/boot/dts/exynos4412-tiny4412.dts index 525684ca8dc0..4840bbdaa9ec 100644 --- a/arch/arm/boot/dts/exynos4412-tiny4412.dts +++ b/arch/arm/boot/dts/exynos4412-tiny4412.dts @@ -13,6 +13,7 @@ /dts-v1/; #include "exynos4412.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "FriendlyARM TINY4412 board based on Exynos4412"; @@ -31,26 +32,26 @@ led1 { label = "led1"; - gpios = <&gpm4 0 1>; + gpios = <&gpm4 0 GPIO_ACTIVE_LOW>; default-state = "off"; linux,default-trigger = "heartbeat"; }; led2 { label = "led2"; - gpios = <&gpm4 1 1>; + gpios = <&gpm4 1 GPIO_ACTIVE_LOW>; default-state = "off"; }; led3 { label = "led3"; - gpios = <&gpm4 2 1>; + gpios = <&gpm4 2 GPIO_ACTIVE_LOW>; default-state = "off"; }; led4 { label = "led4"; - gpios = <&gpm4 3 1>; + gpios = <&gpm4 3 GPIO_ACTIVE_LOW>; default-state = "off"; linux,default-trigger = "mmc0"; }; diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts index 2a1ebb76ebe0..40a474c4374b 100644 --- a/arch/arm/boot/dts/exynos4412-trats2.dts +++ b/arch/arm/boot/dts/exynos4412-trats2.dts @@ -65,7 +65,7 @@ regulator-name = "CAM_SENSOR_A"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpm0 2 0>; + gpio = <&gpm0 2 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -74,7 +74,7 @@ regulator-name = "LCD_VDD_2.2V"; regulator-min-microvolt = <2200000>; regulator-max-microvolt = <2200000>; - gpio = <&gpc0 1 0>; + gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -83,7 +83,7 @@ regulator-name = "CAM_AF"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&gpm0 4 0>; + gpio = <&gpm0 4 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -92,7 +92,7 @@ regulator-name = "LED_A_3.0V"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; - gpio = <&gpj0 5 0>; + gpio = <&gpj0 5 GPIO_ACTIVE_HIGH>; enable-active-high; }; }; @@ -101,21 +101,21 @@ compatible = "gpio-keys"; key-down { - gpios = <&gpx3 3 1>; + gpios = <&gpx3 3 GPIO_ACTIVE_LOW>; linux,code = <114>; label = "volume down"; debounce-interval = <10>; }; key-up { - gpios = <&gpx2 2 1>; + gpios = <&gpx2 2 GPIO_ACTIVE_LOW>; linux,code = <115>; label = "volume up"; debounce-interval = <10>; }; key-power { - gpios = <&gpx2 7 1>; + gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; linux,code = <116>; label = "power"; debounce-interval = <10>; @@ -123,7 +123,7 @@ }; key-ok { - gpios = <&gpx0 1 1>; + gpios = <&gpx0 1 GPIO_ACTIVE_LOW>; linux,code = <139>; label = "ok"; debounce-inteval = <10>; @@ -198,7 +198,7 @@ i2c_ak8975: i2c-gpio-0 { compatible = "i2c-gpio"; - gpios = <&gpy2 4 0>, <&gpy2 5 0>; + gpios = <&gpy2 4 GPIO_ACTIVE_HIGH>, <&gpy2 5 GPIO_ACTIVE_HIGH>; i2c-gpio,delay-us = <2>; #address-cells = <1>; #size-cells = <0>; @@ -207,13 +207,13 @@ ak8975@0c { compatible = "asahi-kasei,ak8975"; reg = <0x0c>; - gpios = <&gpj0 7 0>; + gpios = <&gpj0 7 GPIO_ACTIVE_HIGH>; }; }; i2c_cm36651: i2c-gpio-2 { compatible = "i2c-gpio"; - gpios = <&gpf0 0 1>, <&gpf0 1 1>; + gpios = <&gpf0 0 GPIO_ACTIVE_LOW>, <&gpf0 1 GPIO_ACTIVE_LOW>; i2c-gpio,delay-us = <2>; #address-cells = <1>; #size-cells = <0>; @@ -359,7 +359,7 @@ reg = <0>; vdd3-supply = <&lcd_vdd3_reg>; vci-supply = <&ldo25_reg>; - reset-gpios = <&gpy4 5 0>; + reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>; power-on-delay= <50>; reset-delay = <100>; init-delay = <100>; @@ -391,6 +391,7 @@ }; &exynos_usbphy { + vbus-supply = <&esafeout1_reg>; status = "okay"; }; @@ -446,7 +447,7 @@ clocks = <&camera 1>; clock-names = "extclk"; samsung,camclk-out = <1>; - gpios = <&gpm1 6 0>; + gpios = <&gpm1 6 GPIO_ACTIVE_HIGH>; port { is_s5k6a3_ep: endpoint { @@ -488,8 +489,8 @@ s5c73m3@3c { compatible = "samsung,s5c73m3"; reg = <0x3c>; - standby-gpios = <&gpm0 1 1>; /* ISP_STANDBY */ - xshutdown-gpios = <&gpf1 3 1>; /* ISP_RESET */ + standby-gpios = <&gpm0 1 GPIO_ACTIVE_LOW>; /* ISP_STANDBY */ + xshutdown-gpios = <&gpf1 3 GPIO_ACTIVE_LOW>; /* ISP_RESET */ vdd-int-supply = <&buck9_reg>; vddio-cis-supply = <&ldo9_reg>; vdda-supply = <&ldo17_reg>; @@ -564,16 +565,14 @@ #clock-cells = <1>; voltage-regulators { - ldo1_reg: ldo1 { - regulator-compatible = "LDO1"; + ldo1_reg: LDO1 { regulator-name = "VALIVE_1.0V_AP"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; regulator-always-on; }; - ldo2_reg: ldo2 { - regulator-compatible = "LDO2"; + ldo2_reg: LDO2 { regulator-name = "VM1M2_1.2V_AP"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; @@ -583,32 +582,28 @@ }; }; - ldo3_reg: ldo3 { - regulator-compatible = "LDO3"; + ldo3_reg: LDO3 { regulator-name = "VCC_1.8V_AP"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-always-on; }; - ldo4_reg: ldo4 { - regulator-compatible = "LDO4"; + ldo4_reg: LDO4 { regulator-name = "VCC_2.8V_AP"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; regulator-always-on; }; - ldo5_reg: ldo5 { - regulator-compatible = "LDO5"; + ldo5_reg: LDO5 { regulator-name = "VCC_1.8V_IO"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-always-on; }; - ldo6_reg: ldo6 { - regulator-compatible = "LDO6"; + ldo6_reg: LDO6 { regulator-name = "VMPLL_1.0V_AP"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; @@ -618,8 +613,7 @@ }; }; - ldo7_reg: ldo7 { - regulator-compatible = "LDO7"; + ldo7_reg: LDO7 { regulator-name = "VPLL_1.0V_AP"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; @@ -629,8 +623,7 @@ }; }; - ldo8_reg: ldo8 { - regulator-compatible = "LDO8"; + ldo8_reg: LDO8 { regulator-name = "VMIPI_1.0V"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; @@ -639,15 +632,13 @@ }; }; - ldo9_reg: ldo9 { - regulator-compatible = "LDO9"; + ldo9_reg: LDO9 { regulator-name = "CAM_ISP_MIPI_1.2V"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; }; - ldo10_reg: ldo10 { - regulator-compatible = "LDO10"; + ldo10_reg: LDO10 { regulator-name = "VMIPI_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -656,8 +647,7 @@ }; }; - ldo11_reg: ldo11 { - regulator-compatible = "LDO11"; + ldo11_reg: LDO11 { regulator-name = "VABB1_1.95V"; regulator-min-microvolt = <1950000>; regulator-max-microvolt = <1950000>; @@ -667,8 +657,7 @@ }; }; - ldo12_reg: ldo12 { - regulator-compatible = "LDO12"; + ldo12_reg: LDO12 { regulator-name = "VUOTG_3.0V"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; @@ -677,15 +666,13 @@ }; }; - ldo13_reg: ldo13 { - regulator-compatible = "LDO13"; + ldo13_reg: LDO13 { regulator-name = "NFC_AVDD_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; - ldo14_reg: ldo14 { - regulator-compatible = "LDO14"; + ldo14_reg: LDO14 { regulator-name = "VABB2_1.95V"; regulator-min-microvolt = <1950000>; regulator-max-microvolt = <1950000>; @@ -695,8 +682,7 @@ }; }; - ldo15_reg: ldo15 { - regulator-compatible = "LDO15"; + ldo15_reg: LDO15 { regulator-name = "VHSIC_1.0V"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; @@ -705,8 +691,7 @@ }; }; - ldo16_reg: ldo16 { - regulator-compatible = "LDO16"; + ldo16_reg: LDO16 { regulator-name = "VHSIC_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -715,80 +700,69 @@ }; }; - ldo17_reg: ldo17 { - regulator-compatible = "LDO17"; + ldo17_reg: LDO17 { regulator-name = "CAM_SENSOR_CORE_1.2V"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; }; - ldo18_reg: ldo18 { - regulator-compatible = "LDO18"; + ldo18_reg: LDO18 { regulator-name = "CAM_ISP_SEN_IO_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; - ldo19_reg: ldo19 { - regulator-compatible = "LDO19"; + ldo19_reg: LDO19 { regulator-name = "VT_CAM_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; - ldo20_reg: ldo20 { - regulator-compatible = "LDO20"; + ldo20_reg: LDO20 { regulator-name = "VDDQ_PRE_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; - ldo21_reg: ldo21 { - regulator-compatible = "LDO21"; + ldo21_reg: LDO21 { regulator-name = "VTF_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>; }; - ldo22_reg: ldo22 { - regulator-compatible = "LDO22"; + ldo22_reg: LDO22 { regulator-name = "VMEM_VDD_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; }; - ldo23_reg: ldo23 { - regulator-compatible = "LDO23"; + ldo23_reg: LDO23 { regulator-name = "TSP_AVDD_3.3V"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; - ldo24_reg: ldo24 { - regulator-compatible = "LDO24"; + ldo24_reg: LDO24 { regulator-name = "TSP_VDD_1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; - ldo25_reg: ldo25 { - regulator-compatible = "LDO25"; + ldo25_reg: LDO25 { regulator-name = "LCD_VCC_3.3V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; }; - ldo26_reg: ldo26 { - regulator-compatible = "LDO26"; + ldo26_reg: LDO26 { regulator-name = "MOTOR_VCC_3.0V"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; }; - buck1_reg: buck1 { - regulator-compatible = "BUCK1"; + buck1_reg: BUCK1 { regulator-name = "vdd_mif"; regulator-min-microvolt = <850000>; regulator-max-microvolt = <1100000>; @@ -799,8 +773,7 @@ }; }; - buck2_reg: buck2 { - regulator-compatible = "BUCK2"; + buck2_reg: BUCK2 { regulator-name = "vdd_arm"; regulator-min-microvolt = <850000>; regulator-max-microvolt = <1500000>; @@ -811,8 +784,7 @@ }; }; - buck3_reg: buck3 { - regulator-compatible = "BUCK3"; + buck3_reg: BUCK3 { regulator-name = "vdd_int"; regulator-min-microvolt = <850000>; regulator-max-microvolt = <1150000>; @@ -823,8 +795,7 @@ }; }; - buck4_reg: buck4 { - regulator-compatible = "BUCK4"; + buck4_reg: BUCK4 { regulator-name = "vdd_g3d"; regulator-min-microvolt = <850000>; regulator-max-microvolt = <1150000>; @@ -834,40 +805,35 @@ }; }; - buck5_reg: buck5 { - regulator-compatible = "BUCK5"; + buck5_reg: BUCK5 { regulator-name = "VMEM_1.2V_AP"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-always-on; }; - buck6_reg: buck6 { - regulator-compatible = "BUCK6"; + buck6_reg: BUCK6 { regulator-name = "VCC_SUB_1.35V"; regulator-min-microvolt = <1350000>; regulator-max-microvolt = <1350000>; regulator-always-on; }; - buck7_reg: buck7 { - regulator-compatible = "BUCK7"; + buck7_reg: BUCK7 { regulator-name = "VCC_SUB_2.0V"; regulator-min-microvolt = <2000000>; regulator-max-microvolt = <2000000>; regulator-always-on; }; - buck8_reg: buck8 { - regulator-compatible = "BUCK8"; + buck8_reg: BUCK8 { regulator-name = "VMEM_VDDF_3.0V"; regulator-min-microvolt = <2850000>; regulator-max-microvolt = <2850000>; maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; }; - buck9_reg: buck9 { - regulator-compatible = "BUCK9"; + buck9_reg: BUCK9 { regulator-name = "CAM_ISP_CORE_1.2V"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1200000>; @@ -1276,7 +1242,7 @@ &sdhci_2 { bus-width = <4>; - cd-gpios = <&gpx3 4 0>; + cd-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>; cd-inverted; pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>; pinctrl-names = "default"; @@ -1303,7 +1269,7 @@ &spi_1 { pinctrl-names = "default"; pinctrl-0 = <&spi1_bus>; - cs-gpios = <&gpb 5 0>; + cs-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>; status = "okay"; s5c73m3_spi: s5c73m3 { diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts index db3f65f3eb45..c000532c1444 100644 --- a/arch/arm/boot/dts/exynos5250-arndale.dts +++ b/arch/arm/boot/dts/exynos5250-arndale.dts @@ -129,10 +129,6 @@ samsung,color-depth = <1>; samsung,link-rate = <0x0a>; samsung,lane-count = <4>; -}; - -&fimd { - status = "okay"; display-timings { native-mode = <&timing0>; @@ -152,6 +148,10 @@ }; }; +&fimd { + status = "okay"; +}; + &hdmi { hpd-gpio = <&gpx3 7 GPIO_ACTIVE_LOW>; vdd_osc-supply = <&ldo10_reg>; diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts index c625e71217aa..0f5dcd418af8 100644 --- a/arch/arm/boot/dts/exynos5250-smdk5250.dts +++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts @@ -89,14 +89,6 @@ pinctrl-names = "default"; pinctrl-0 = <&dp_hpd>; status = "okay"; -}; - -&ehci { - samsung,vbus-gpio = <&gpx2 6 GPIO_ACTIVE_HIGH>; -}; - -&fimd { - status = "okay"; display-timings { native-mode = <&timing0>; @@ -116,6 +108,14 @@ }; }; +&ehci { + samsung,vbus-gpio = <&gpx2 6 GPIO_ACTIVE_HIGH>; +}; + +&fimd { + status = "okay"; +}; + &hdmi { hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm/boot/dts/exynos5250-snow-common.dtsi b/arch/arm/boot/dts/exynos5250-snow-common.dtsi new file mode 100644 index 000000000000..0a7f408824d8 --- /dev/null +++ b/arch/arm/boot/dts/exynos5250-snow-common.dtsi @@ -0,0 +1,684 @@ +/* + * Google Snow board device tree source + * + * Copyright (c) 2012 Google, Inc + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/clock/maxim,max77686.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/input/input.h> +#include "exynos5250.dtsi" + +/ { + aliases { + i2c104 = &i2c_104; + }; + + memory { + reg = <0x40000000 0x80000000>; + }; + + chosen { + bootargs = "console=tty1"; + stdout-path = "serial3:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&power_key_irq &lid_irq>; + + power { + label = "Power"; + gpios = <&gpx1 3 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + gpio-key,wakeup; + }; + + lid-switch { + label = "Lid"; + gpios = <&gpx3 5 GPIO_ACTIVE_LOW>; + linux,input-type = <5>; /* EV_SW */ + linux,code = <0>; /* SW_LID */ + debounce-interval = <1>; + gpio-key,wakeup; + }; + }; + + vbat: vbat-fixed-regulator { + compatible = "regulator-fixed"; + regulator-name = "vbat-supply"; + regulator-boot-on; + }; + + i2c-arbitrator { + compatible = "i2c-arb-gpio-challenge"; + #address-cells = <1>; + #size-cells = <0>; + + i2c-parent = <&{/i2c@12CA0000}>; + + our-claim-gpio = <&gpf0 3 GPIO_ACTIVE_LOW>; + their-claim-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>; + slew-delay-us = <10>; + wait-retry-us = <3000>; + wait-free-us = <50000>; + + pinctrl-names = "default"; + pinctrl-0 = <&arb_our_claim &arb_their_claim>; + + /* Use ID 104 as a hint that we're on physical bus 4 */ + i2c_104: i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + battery: sbs-battery@b { + compatible = "sbs,sbs-battery"; + reg = <0xb>; + sbs,poll-retry-count = <1>; + }; + + cros_ec: embedded-controller { + compatible = "google,cros-ec-i2c"; + reg = <0x1e>; + interrupts = <6 IRQ_TYPE_NONE>; + interrupt-parent = <&gpx1>; + pinctrl-names = "default"; + pinctrl-0 = <&ec_irq>; + wakeup-source; + }; + + power-regulator { + compatible = "ti,tps65090"; + reg = <0x48>; + + /* + * Config irq to disable internal pulls + * even though we run in polling mode. + */ + pinctrl-names = "default"; + pinctrl-0 = <&tps65090_irq>; + + vsys1-supply = <&vbat>; + vsys2-supply = <&vbat>; + vsys3-supply = <&vbat>; + infet1-supply = <&vbat>; + infet2-supply = <&vbat>; + infet3-supply = <&vbat>; + infet4-supply = <&vbat>; + infet5-supply = <&vbat>; + infet6-supply = <&vbat>; + infet7-supply = <&vbat>; + vsys-l1-supply = <&vbat>; + vsys-l2-supply = <&vbat>; + + regulators { + dcdc1 { + ti,enable-ext-control; + }; + dcdc2 { + ti,enable-ext-control; + }; + dcdc3 { + ti,enable-ext-control; + }; + fet1: fet1 { + regulator-name = "vcd_led"; + ti,overcurrent-wait = <3>; + }; + tps65090_fet2: fet2 { + regulator-name = "video_mid"; + regulator-always-on; + ti,overcurrent-wait = <3>; + }; + fet3 { + regulator-name = "wwan_r"; + regulator-always-on; + ti,overcurrent-wait = <3>; + }; + fet4 { + regulator-name = "sdcard"; + ti,overcurrent-wait = <3>; + }; + fet5 { + regulator-name = "camout"; + regulator-always-on; + ti,overcurrent-wait = <3>; + }; + fet6: fet6 { + regulator-name = "lcd_vdd"; + ti,overcurrent-wait = <3>; + }; + tps65090_fet7: fet7 { + regulator-name = "video_mid_1a"; + regulator-always-on; + ti,overcurrent-wait = <3>; + }; + ldo1 { + }; + ldo2 { + }; + }; + + charger { + compatible = "ti,tps65090-charger"; + }; + }; + }; + }; + + sound { + samsung,i2s-controller = <&i2s0>; + }; + + usb3_vbus_reg: regulator-usb3 { + compatible = "regulator-fixed"; + regulator-name = "P5.0V_USB3CON"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpx2 7 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb3_vbus_en>; + enable-active-high; + }; + + fixed-rate-clocks { + xxti { + compatible = "samsung,clock-xxti"; + clock-frequency = <24000000>; + }; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 1000000 0>; + brightness-levels = <0 100 500 1000 1500 2000 2500 2800>; + default-brightness-level = <7>; + enable-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>; + power-supply = <&fet1>; + pinctrl-0 = <&pwm0_out>; + pinctrl-names = "default"; + }; + + panel: panel { + compatible = "auo,b116xw03"; + power-supply = <&fet6>; + backlight = <&backlight>; + + port { + panel_in: endpoint { + remote-endpoint = <&bridge_out>; + }; + }; + }; + + mmc3_pwrseq: mmc3_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpx0 2 GPIO_ACTIVE_LOW>, /* WIFI_RSTn */ + <&gpx0 1 GPIO_ACTIVE_LOW>; /* WIFI_EN */ + clocks = <&max77686 MAX77686_CLK_PMIC>; + clock-names = "ext_clock"; + }; +}; + +&cpu0 { + cpu0-supply = <&buck2_reg>; +}; + +&dp { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&dp_hpd>; + samsung,color-space = <0>; + samsung,dynamic-range = <0>; + samsung,ycbcr-coeff = <0>; + samsung,color-depth = <1>; + samsung,link-rate = <0x0a>; + samsung,lane-count = <2>; + samsung,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>; + + ports { + port@0 { + dp_out: endpoint { + remote-endpoint = <&bridge_in>; + }; + }; + }; +}; + +&ehci { + samsung,vbus-gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>; +}; + +&fimd { + status = "okay"; + samsung,invert-vclk; +}; + +&hdmi { + hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_hpd_irq>; + phy = <&hdmiphy>; + ddc = <&i2c_2>; + hdmi-en-supply = <&tps65090_fet7>; + vdd-supply = <&ldo8_reg>; + vdd_osc-supply = <&ldo10_reg>; + vdd_pll-supply = <&ldo8_reg>; +}; + +&i2c_0 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <378000>; + + max77686: max77686@09 { + compatible = "maxim,max77686"; + interrupt-parent = <&gpx3>; + interrupts = <2 IRQ_TYPE_NONE>; + pinctrl-names = "default"; + pinctrl-0 = <&max77686_irq>; + wakeup-source; + reg = <0x09>; + #clock-cells = <1>; + + voltage-regulators { + ldo1_reg: LDO1 { + regulator-name = "P1.0V_LDO_OUT1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "P1.8V_LDO_OUT2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "P1.8V_LDO_OUT3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo7_reg: LDO7 { + regulator-name = "P1.1V_LDO_OUT7"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + ldo8_reg: LDO8 { + regulator-name = "P1.0V_LDO_OUT8"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo10_reg: LDO10 { + regulator-name = "P1.8V_LDO_OUT10"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo12_reg: LDO12 { + regulator-name = "P3.0V_LDO_OUT12"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + + ldo14_reg: LDO14 { + regulator-name = "P1.8V_LDO_OUT14"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo15_reg: LDO15 { + regulator-name = "P1.0V_LDO_OUT15"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo16_reg: LDO16 { + regulator-name = "P1.8V_LDO_OUT16"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + buck3_reg: BUCK3 { + regulator-name = "vdd_int"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + buck4_reg: BUCK4 { + regulator-name = "vdd_g3d"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + buck5_reg: BUCK5 { + regulator-name = "P1.8V_BUCK_OUT5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + buck6_reg: BUCK6 { + regulator-name = "P1.35V_BUCK_OUT6"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + buck7_reg: BUCK7 { + regulator-name = "P2.0V_BUCK_OUT7"; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + }; + + buck8_reg: BUCK8 { + regulator-name = "P2.85V_BUCK_OUT8"; + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + }; + }; + }; +}; + +&i2c_1 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <378000>; + + trackpad { + reg = <0x67>; + compatible = "cypress,cyapa"; + interrupts = <2 IRQ_TYPE_NONE>; + interrupt-parent = <&gpx1>; + wakeup-source; + }; +}; + +/* + * Disabled pullups since external part has its own pullups and + * double-pulling gets us out of spec in some cases. + */ +&i2c2_bus { + samsung,pin-pud = <0>; +}; + +&i2c_2 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; + + hdmiddc@50 { + compatible = "samsung,exynos4210-hdmiddc"; + reg = <0x50>; + }; +}; + +&i2c_3 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; +}; + +&i2c_4 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; +}; + +&i2c_5 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; +}; + +&i2c_7 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; + + ptn3460: lvds-bridge@20 { + compatible = "nxp,ptn3460"; + reg = <0x20>; + powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>; + edid-emulation = <5>; + + ports { + port@0 { + bridge_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + + port@1 { + bridge_in: endpoint { + remote-endpoint = <&dp_out>; + }; + }; + }; + }; +}; + +&i2c_8 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <378000>; + + hdmiphy: hdmiphy@38 { + compatible = "samsung,exynos4212-hdmiphy"; + reg = <0x38>; + }; +}; + +&i2s0 { + status = "okay"; +}; + +&mmc_0 { + status = "okay"; + num-slots = <1>; + broken-cd; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>; + bus-width = <8>; + cap-mmc-highspeed; +}; + +&mmc_2 { + status = "okay"; + num-slots = <1>; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; + bus-width = <4>; + wp-gpios = <&gpc2 1 GPIO_ACTIVE_HIGH>; + cap-sd-highspeed; +}; + +/* + * On Snow we've got SIP WiFi and so can keep drive strengths low to + * reduce EMI. + */ +&mmc_3 { + status = "okay"; + num-slots = <1>; + broken-cd; + cap-sdio-irq; + keep-power-in-suspend; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4 &wifi_en &wifi_rst>; + bus-width = <4>; + cap-sd-highspeed; + mmc-pwrseq = <&mmc3_pwrseq>; +}; + +&pinctrl_0 { + wifi_en: wifi-en { + samsung,pins = "gpx0-1"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + wifi_rst: wifi-rst { + samsung,pins = "gpx0-2"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + power_key_irq: power-key-irq { + samsung,pins = "gpx1-3"; + samsung,pin-function = <0xf>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + ec_irq: ec-irq { + samsung,pins = "gpx1-6"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + tps65090_irq: tps65090-irq { + samsung,pins = "gpx2-6"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + usb3_vbus_en: usb3-vbus-en { + samsung,pins = "gpx2-7"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + max77686_irq: max77686-irq { + samsung,pins = "gpx3-2"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + lid_irq: lid-irq { + samsung,pins = "gpx3-5"; + samsung,pin-function = <0xf>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + hdmi_hpd_irq: hdmi-hpd-irq { + samsung,pins = "gpx3-7"; + samsung,pin-function = <0>; + samsung,pin-pud = <1>; + samsung,pin-drv = <0>; + }; +}; + +&pinctrl_1 { + arb_their_claim: arb-their-claim { + samsung,pins = "gpe0-4"; + samsung,pin-function = <0>; + samsung,pin-pud = <3>; + samsung,pin-drv = <0>; + }; + + arb_our_claim: arb-our-claim { + samsung,pins = "gpf0-3"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; +}; + +&rtc { + status = "okay"; + clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>; + clock-names = "rtc", "rtc_src"; +}; + +&sd3_bus4 { + samsung,pin-drv = <0>; +}; + +&sd3_clk { + samsung,pin-drv = <0>; +}; + +&sd3_cmd { + samsung,pin-pud = <3>; + samsung,pin-drv = <0>; +}; + +&spi_1 { + status = "okay"; + samsung,spi-src-clk = <0>; + num-cs = <1>; + cs-gpios = <&gpa2 5 GPIO_ACTIVE_HIGH>; +}; + +&usbdrd_dwc3 { + dr_mode = "host"; +}; + +&usbdrd_phy { + vbus-supply = <&usb3_vbus_reg>; +}; + +#include "cros-ec-keyboard.dtsi" diff --git a/arch/arm/boot/dts/exynos5250-snow-rev5.dts b/arch/arm/boot/dts/exynos5250-snow-rev5.dts new file mode 100644 index 000000000000..f811dc800660 --- /dev/null +++ b/arch/arm/boot/dts/exynos5250-snow-rev5.dts @@ -0,0 +1,47 @@ +/* + * Google Snow Rev 5+ board device tree source + * + * Copyright (c) 2012 Google, Inc + * Copyright (c) 2015 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; +#include "exynos5250-snow-common.dtsi" + +/ { + model = "Google Snow Rev 5+"; + compatible = "google,snow-rev5", "samsung,exynos5250", + "samsung,exynos5"; + + sound { + compatible = "google,snow-audio-max98090"; + + samsung,model = "Snow-I2S-MAX98090"; + samsung,audio-codec = <&max98090>; + }; +}; + +&i2c_7 { + max98090: codec@10 { + compatible = "maxim,max98090"; + reg = <0x10>; + interrupts = <4 IRQ_TYPE_NONE>; + interrupt-parent = <&gpx0>; + pinctrl-names = "default"; + pinctrl-0 = <&max98090_irq>; + }; +}; + +&pinctrl_0 { + max98090_irq: max98090-irq { + samsung,pins = "gpx0-4"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; +}; diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts index 0720caab5511..995c7ce6c12b 100644 --- a/arch/arm/boot/dts/exynos5250-snow.dts +++ b/arch/arm/boot/dts/exynos5250-snow.dts @@ -9,698 +9,35 @@ */ /dts-v1/; -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/clock/maxim,max77686.h> -#include <dt-bindings/interrupt-controller/irq.h> -#include <dt-bindings/input/input.h> -#include "exynos5250.dtsi" +#include "exynos5250-snow-common.dtsi" / { model = "Google Snow"; - compatible = "google,snow", "samsung,exynos5250", "samsung,exynos5"; - - aliases { - i2c104 = &i2c_104; - }; - - memory { - reg = <0x40000000 0x80000000>; - }; - - chosen { - bootargs = "console=tty1"; - stdout-path = "serial3:115200n8"; - }; - - gpio-keys { - compatible = "gpio-keys"; - pinctrl-names = "default"; - pinctrl-0 = <&power_key_irq &lid_irq>; - - power { - label = "Power"; - gpios = <&gpx1 3 GPIO_ACTIVE_LOW>; - linux,code = <KEY_POWER>; - gpio-key,wakeup; - }; - - lid-switch { - label = "Lid"; - gpios = <&gpx3 5 GPIO_ACTIVE_LOW>; - linux,input-type = <5>; /* EV_SW */ - linux,code = <0>; /* SW_LID */ - debounce-interval = <1>; - gpio-key,wakeup; - }; - }; - - vbat: vbat-fixed-regulator { - compatible = "regulator-fixed"; - regulator-name = "vbat-supply"; - regulator-boot-on; - }; - - i2c-arbitrator { - compatible = "i2c-arb-gpio-challenge"; - #address-cells = <1>; - #size-cells = <0>; - - i2c-parent = <&{/i2c@12CA0000}>; - - our-claim-gpio = <&gpf0 3 GPIO_ACTIVE_LOW>; - their-claim-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>; - slew-delay-us = <10>; - wait-retry-us = <3000>; - wait-free-us = <50000>; - - pinctrl-names = "default"; - pinctrl-0 = <&arb_our_claim &arb_their_claim>; - - /* Use ID 104 as a hint that we're on physical bus 4 */ - i2c_104: i2c@0 { - reg = <0>; - #address-cells = <1>; - #size-cells = <0>; - - battery: sbs-battery@b { - compatible = "sbs,sbs-battery"; - reg = <0xb>; - sbs,poll-retry-count = <1>; - }; - - cros_ec: embedded-controller { - compatible = "google,cros-ec-i2c"; - reg = <0x1e>; - interrupts = <6 IRQ_TYPE_NONE>; - interrupt-parent = <&gpx1>; - pinctrl-names = "default"; - pinctrl-0 = <&ec_irq>; - wakeup-source; - }; - - power-regulator { - compatible = "ti,tps65090"; - reg = <0x48>; - - /* - * Config irq to disable internal pulls - * even though we run in polling mode. - */ - pinctrl-names = "default"; - pinctrl-0 = <&tps65090_irq>; - - vsys1-supply = <&vbat>; - vsys2-supply = <&vbat>; - vsys3-supply = <&vbat>; - infet1-supply = <&vbat>; - infet2-supply = <&vbat>; - infet3-supply = <&vbat>; - infet4-supply = <&vbat>; - infet5-supply = <&vbat>; - infet6-supply = <&vbat>; - infet7-supply = <&vbat>; - vsys-l1-supply = <&vbat>; - vsys-l2-supply = <&vbat>; - - regulators { - dcdc1 { - ti,enable-ext-control; - }; - dcdc2 { - ti,enable-ext-control; - }; - dcdc3 { - ti,enable-ext-control; - }; - fet1: fet1 { - regulator-name = "vcd_led"; - ti,overcurrent-wait = <3>; - }; - tps65090_fet2: fet2 { - regulator-name = "video_mid"; - regulator-always-on; - ti,overcurrent-wait = <3>; - }; - fet3 { - regulator-name = "wwan_r"; - regulator-always-on; - ti,overcurrent-wait = <3>; - }; - fet4 { - regulator-name = "sdcard"; - ti,overcurrent-wait = <3>; - }; - fet5 { - regulator-name = "camout"; - regulator-always-on; - ti,overcurrent-wait = <3>; - }; - fet6: fet6 { - regulator-name = "lcd_vdd"; - ti,overcurrent-wait = <3>; - }; - tps65090_fet7: fet7 { - regulator-name = "video_mid_1a"; - regulator-always-on; - ti,overcurrent-wait = <3>; - }; - ldo1 { - }; - ldo2 { - }; - }; - - charger { - compatible = "ti,tps65090-charger"; - }; - }; - }; - }; + compatible = "google,snow-rev4", "google,snow", "samsung,exynos5250", + "samsung,exynos5"; sound { compatible = "google,snow-audio-max98095"; samsung,model = "Snow-I2S-MAX98095"; - samsung,i2s-controller = <&i2s0>; samsung,audio-codec = <&max98095>; }; - - usb3_vbus_reg: regulator-usb3 { - compatible = "regulator-fixed"; - regulator-name = "P5.0V_USB3CON"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - gpio = <&gpx2 7 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&usb3_vbus_en>; - enable-active-high; - }; - - fixed-rate-clocks { - xxti { - compatible = "samsung,clock-xxti"; - clock-frequency = <24000000>; - }; - }; - - backlight: backlight { - compatible = "pwm-backlight"; - pwms = <&pwm 0 1000000 0>; - brightness-levels = <0 100 500 1000 1500 2000 2500 2800>; - default-brightness-level = <7>; - enable-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>; - power-supply = <&fet1>; - pinctrl-0 = <&pwm0_out>; - pinctrl-names = "default"; - }; - - panel: panel { - compatible = "auo,b116xw03"; - power-supply = <&fet6>; - backlight = <&backlight>; - - port { - panel_in: endpoint { - remote-endpoint = <&bridge_out>; - }; - }; - }; - - mmc3_pwrseq: mmc3_pwrseq { - compatible = "mmc-pwrseq-simple"; - reset-gpios = <&gpx0 2 GPIO_ACTIVE_LOW>, /* WIFI_RSTn */ - <&gpx0 1 GPIO_ACTIVE_LOW>; /* WIFI_EN */ - clocks = <&max77686 MAX77686_CLK_PMIC>; - clock-names = "ext_clock"; - }; -}; - -&cpu0 { - cpu0-supply = <&buck2_reg>; -}; - -&dp { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&dp_hpd>; - samsung,color-space = <0>; - samsung,dynamic-range = <0>; - samsung,ycbcr-coeff = <0>; - samsung,color-depth = <1>; - samsung,link-rate = <0x0a>; - samsung,lane-count = <2>; - samsung,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>; - - ports { - port@0 { - dp_out: endpoint { - remote-endpoint = <&bridge_in>; - }; - }; - }; -}; - -&ehci { - samsung,vbus-gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>; -}; - -&fimd { - status = "okay"; - samsung,invert-vclk; -}; - -&hdmi { - hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&hdmi_hpd_irq>; - phy = <&hdmiphy>; - ddc = <&i2c_2>; - hdmi-en-supply = <&tps65090_fet7>; - vdd-supply = <&ldo8_reg>; - vdd_osc-supply = <&ldo10_reg>; - vdd_pll-supply = <&ldo8_reg>; -}; - -&i2c_0 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <378000>; - - max77686: max77686@09 { - compatible = "maxim,max77686"; - interrupt-parent = <&gpx3>; - interrupts = <2 IRQ_TYPE_NONE>; - pinctrl-names = "default"; - pinctrl-0 = <&max77686_irq>; - wakeup-source; - reg = <0x09>; - #clock-cells = <1>; - - voltage-regulators { - ldo1_reg: LDO1 { - regulator-name = "P1.0V_LDO_OUT1"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; - regulator-always-on; - }; - - ldo2_reg: LDO2 { - regulator-name = "P1.8V_LDO_OUT2"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - ldo3_reg: LDO3 { - regulator-name = "P1.8V_LDO_OUT3"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - ldo7_reg: LDO7 { - regulator-name = "P1.1V_LDO_OUT7"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - }; - - ldo8_reg: LDO8 { - regulator-name = "P1.0V_LDO_OUT8"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; - regulator-always-on; - }; - - ldo10_reg: LDO10 { - regulator-name = "P1.8V_LDO_OUT10"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - ldo12_reg: LDO12 { - regulator-name = "P3.0V_LDO_OUT12"; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - regulator-always-on; - }; - - ldo14_reg: LDO14 { - regulator-name = "P1.8V_LDO_OUT14"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - ldo15_reg: LDO15 { - regulator-name = "P1.0V_LDO_OUT15"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; - regulator-always-on; - }; - - ldo16_reg: LDO16 { - regulator-name = "P1.8V_LDO_OUT16"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - buck1_reg: BUCK1 { - regulator-name = "vdd_mif"; - regulator-min-microvolt = <950000>; - regulator-max-microvolt = <1300000>; - regulator-always-on; - regulator-boot-on; - }; - - buck2_reg: BUCK2 { - regulator-name = "vdd_arm"; - regulator-min-microvolt = <850000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-boot-on; - }; - - buck3_reg: BUCK3 { - regulator-name = "vdd_int"; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1200000>; - regulator-always-on; - regulator-boot-on; - }; - - buck4_reg: BUCK4 { - regulator-name = "vdd_g3d"; - regulator-min-microvolt = <850000>; - regulator-max-microvolt = <1300000>; - regulator-always-on; - regulator-boot-on; - }; - - buck5_reg: BUCK5 { - regulator-name = "P1.8V_BUCK_OUT5"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - buck6_reg: BUCK6 { - regulator-name = "P1.35V_BUCK_OUT6"; - regulator-min-microvolt = <1350000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - }; - - buck7_reg: BUCK7 { - regulator-name = "P2.0V_BUCK_OUT7"; - regulator-min-microvolt = <2000000>; - regulator-max-microvolt = <2000000>; - regulator-always-on; - }; - - buck8_reg: BUCK8 { - regulator-name = "P2.85V_BUCK_OUT8"; - regulator-min-microvolt = <2850000>; - regulator-max-microvolt = <2850000>; - regulator-always-on; - }; - }; - }; -}; - -&i2c_1 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <378000>; - - trackpad { - reg = <0x67>; - compatible = "cypress,cyapa"; - interrupts = <2 IRQ_TYPE_NONE>; - interrupt-parent = <&gpx1>; - wakeup-source; - }; -}; - -/* - * Disabled pullups since external part has its own pullups and - * double-pulling gets us out of spec in some cases. - */ -&i2c2_bus { - samsung,pin-pud = <0>; -}; - -&i2c_2 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <66000>; - - hdmiddc@50 { - compatible = "samsung,exynos4210-hdmiddc"; - reg = <0x50>; - }; -}; - -&i2c_3 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <66000>; -}; - -&i2c_4 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <66000>; -}; - -&i2c_5 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <66000>; }; &i2c_7 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <66000>; - - ptn3460: lvds-bridge@20 { - compatible = "nxp,ptn3460"; - reg = <0x20>; - powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>; - edid-emulation = <5>; - - ports { - port@0 { - bridge_out: endpoint { - remote-endpoint = <&panel_in>; - }; - }; - - port@1 { - bridge_in: endpoint { - remote-endpoint = <&dp_out>; - }; - }; - }; - }; - max98095: codec@11 { compatible = "maxim,max98095"; reg = <0x11>; - pinctrl-0 = <&max98095_en>; pinctrl-names = "default"; + pinctrl-0 = <&max98095_en>; }; }; -&i2c_8 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <378000>; - - hdmiphy: hdmiphy@38 { - compatible = "samsung,exynos4212-hdmiphy"; - reg = <0x38>; - }; -}; - -&i2s0 { - status = "okay"; -}; - -&mmc_0 { - status = "okay"; - num-slots = <1>; - broken-cd; - card-detect-delay = <200>; - samsung,dw-mshc-ciu-div = <3>; - samsung,dw-mshc-sdr-timing = <2 3>; - samsung,dw-mshc-ddr-timing = <1 2>; - pinctrl-names = "default"; - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>; - bus-width = <8>; - cap-mmc-highspeed; -}; - -&mmc_2 { - status = "okay"; - num-slots = <1>; - card-detect-delay = <200>; - samsung,dw-mshc-ciu-div = <3>; - samsung,dw-mshc-sdr-timing = <2 3>; - samsung,dw-mshc-ddr-timing = <1 2>; - pinctrl-names = "default"; - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; - bus-width = <4>; - wp-gpios = <&gpc2 1 GPIO_ACTIVE_HIGH>; - cap-sd-highspeed; -}; - -/* - * On Snow we've got SIP WiFi and so can keep drive strengths low to - * reduce EMI. - */ -&mmc_3 { - status = "okay"; - num-slots = <1>; - broken-cd; - cap-sdio-irq; - keep-power-in-suspend; - card-detect-delay = <200>; - samsung,dw-mshc-ciu-div = <3>; - samsung,dw-mshc-sdr-timing = <2 3>; - samsung,dw-mshc-ddr-timing = <1 2>; - pinctrl-names = "default"; - pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4 &wifi_en &wifi_rst>; - bus-width = <4>; - cap-sd-highspeed; - mmc-pwrseq = <&mmc3_pwrseq>; -}; - &pinctrl_0 { - wifi_en: wifi-en { - samsung,pins = "gpx0-1"; - samsung,pin-function = <1>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - wifi_rst: wifi-rst { - samsung,pins = "gpx0-2"; - samsung,pin-function = <1>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - power_key_irq: power-key-irq { - samsung,pins = "gpx1-3"; - samsung,pin-function = <0xf>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - ec_irq: ec-irq { - samsung,pins = "gpx1-6"; - samsung,pin-function = <0>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - max98095_en: max98095-en { samsung,pins = "gpx1-7"; samsung,pin-function = <0>; samsung,pin-pud = <3>; samsung,pin-drv = <0>; }; - - tps65090_irq: tps65090-irq { - samsung,pins = "gpx2-6"; - samsung,pin-function = <0>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - usb3_vbus_en: usb3-vbus-en { - samsung,pins = "gpx2-7"; - samsung,pin-function = <1>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - max77686_irq: max77686-irq { - samsung,pins = "gpx3-2"; - samsung,pin-function = <0>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - lid_irq: lid-irq { - samsung,pins = "gpx3-5"; - samsung,pin-function = <0xf>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - hdmi_hpd_irq: hdmi-hpd-irq { - samsung,pins = "gpx3-7"; - samsung,pin-function = <0>; - samsung,pin-pud = <1>; - samsung,pin-drv = <0>; - }; -}; - -&pinctrl_1 { - arb_their_claim: arb-their-claim { - samsung,pins = "gpe0-4"; - samsung,pin-function = <0>; - samsung,pin-pud = <3>; - samsung,pin-drv = <0>; - }; - - arb_our_claim: arb-our-claim { - samsung,pins = "gpf0-3"; - samsung,pin-function = <1>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; }; - -&rtc { - status = "okay"; - clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>; - clock-names = "rtc", "rtc_src"; -}; - -&sd3_bus4 { - samsung,pin-drv = <0>; -}; - -&sd3_clk { - samsung,pin-drv = <0>; -}; - -&sd3_cmd { - samsung,pin-pud = <3>; - samsung,pin-drv = <0>; -}; - -&spi_1 { - status = "okay"; - samsung,spi-src-clk = <0>; - num-cs = <1>; - cs-gpios = <&gpa2 5 GPIO_ACTIVE_HIGH>; -}; - -&usbdrd_dwc3 { - dr_mode = "host"; -}; - -&usbdrd_phy { - vbus-supply = <&usb3_vbus_reg>; -}; - -#include "cros-ec-keyboard.dtsi" diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi index b24610ea8c2a..88b9cf5f226f 100644 --- a/arch/arm/boot/dts/exynos5250.dtsi +++ b/arch/arm/boot/dts/exynos5250.dtsi @@ -130,6 +130,10 @@ compatible = "samsung,exynos4210-pd"; reg = <0x100440A0 0x20>; #power-domain-cells = <0>; + clocks = <&clock CLK_FIN_PLL>, + <&clock CLK_MOUT_ACLK200_DISP1_SUB>, + <&clock CLK_MOUT_ACLK300_DISP1_SUB>; + clock-names = "oscclk", "clk0", "clk1"; }; clock: clock-controller@10010000 { diff --git a/arch/arm/boot/dts/exynos5420-arndale-octa.dts b/arch/arm/boot/dts/exynos5420-arndale-octa.dts index eeb4ac22cfce..4ecef6981d5c 100644 --- a/arch/arm/boot/dts/exynos5420-arndale-octa.dts +++ b/arch/arm/boot/dts/exynos5420-arndale-octa.dts @@ -11,6 +11,7 @@ /dts-v1/; #include "exynos5420.dtsi" +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/input/input.h> #include <dt-bindings/clock/samsung,s2mps11.h> @@ -44,7 +45,7 @@ wakeup { label = "SW-TACT1"; - gpios = <&gpx2 7 1>; + gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; linux,code = <KEY_WAKEUP>; gpio-key,wakeup; }; diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts index 1b95da79293c..72ba6f032ed7 100644 --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts @@ -94,7 +94,7 @@ regulator-name = "P5.0V_USB3CON0"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - gpio = <&gph0 0 0>; + gpio = <&gph0 0 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&usb300_vbus_en>; enable-active-high; @@ -105,7 +105,7 @@ regulator-name = "P5.0V_USB3CON1"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - gpio = <&gph0 1 0>; + gpio = <&gph0 1 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&usb301_vbus_en>; enable-active-high; @@ -153,7 +153,7 @@ samsung,color-depth = <1>; samsung,link-rate = <0x06>; samsung,lane-count = <2>; - samsung,hpd-gpio = <&gpx2 6 0>; + samsung,hpd-gpio = <&gpx2 6 GPIO_ACTIVE_HIGH>; ports { port@0 { @@ -930,7 +930,7 @@ status = "okay"; num-cs = <1>; samsung,spi-src-clk = <0>; - cs-gpios = <&gpb1 2 0>; + cs-gpios = <&gpb1 2 GPIO_ACTIVE_HIGH>; cros_ec: cros-ec@0 { compatible = "google,cros-ec-spi"; @@ -940,6 +940,7 @@ pinctrl-0 = <&ec_spi_cs &ec_irq>; reg = <0>; spi-max-frequency = <3125000>; + google,has-vbc-nvram; controller-data { samsung,spi-feedback-delay = <1>; diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts index 98871f972c8a..ac35aefd320f 100644 --- a/arch/arm/boot/dts/exynos5420-smdk5420.dts +++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts @@ -11,6 +11,7 @@ /dts-v1/; #include "exynos5420.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Samsung SMDK5420 board based on EXYNOS5420"; @@ -69,7 +70,7 @@ regulator-name = "VBUS0"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - gpio = <&gpg0 5 0>; + gpio = <&gpg0 5 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&usb300_vbus_en>; enable-active-high; @@ -80,7 +81,7 @@ regulator-name = "VBUS1"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - gpio = <&gpg1 4 0>; + gpio = <&gpg1 4 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&usb301_vbus_en>; enable-active-high; @@ -98,10 +99,7 @@ samsung,link-rate = <0x0a>; samsung,lane-count = <4>; status = "okay"; -}; -&fimd { - status = "okay"; display-timings { native-mode = <&timing0>; timing0: timing@0 { @@ -118,9 +116,13 @@ }; }; +&fimd { + status = "okay"; +}; + &hdmi { status = "okay"; - hpd-gpio = <&gpx3 7 0>; + hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&hdmi_hpd_irq>; }; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi new file mode 100644 index 000000000000..9493923ec652 --- /dev/null +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi @@ -0,0 +1,61 @@ +/* + * Hardkernel Odroid XU3 Audio Codec device tree source + * + * Copyright (c) 2015 Krzysztof Kozlowski + * Copyright (c) 2014 Collabora Ltd. + * Copyright (c) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/ { + sound: sound { + compatible = "simple-audio-card"; + + simple-audio-card,name = "Odroid-XU3"; + simple-audio-card,widgets = + "Headphone", "Headphone Jack", + "Speakers", "Speakers"; + simple-audio-card,routing = + "Headphone Jack", "HPL", + "Headphone Jack", "HPR", + "Headphone Jack", "MICBIAS", + "IN1", "Headphone Jack", + "Speakers", "SPKL", + "Speakers", "SPKR"; + + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&link0_codec>; + simple-audio-card,frame-master = <&link0_codec>; + + simple-audio-card,cpu { + sound-dai = <&i2s0 0>; + system-clock-frequency = <19200000>; + }; + + link0_codec: simple-audio-card,codec { + sound-dai = <&max98090>; + clocks = <&i2s0 CLK_I2S_CDCLK>; + }; + }; +}; + +&hsi2c_5 { + status = "okay"; + max98090: max98090@10 { + compatible = "maxim,max98090"; + reg = <0x10>; + interrupt-parent = <&gpx3>; + interrupts = <2 0>; + clocks = <&i2s0 CLK_I2S_CDCLK>; + clock-names = "mclk"; + #sound-dai-cells = <0>; + }; +}; + +&i2s0 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi index 3b43e57845ae..1af5bdc2bdb1 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi @@ -43,71 +43,7 @@ pinctrl-0 = <&emmc_nrst_pin>; pinctrl-names = "default"; compatible = "mmc-pwrseq-emmc"; - reset-gpios = <&gpd1 0 1>; - }; - - pwmleds { - compatible = "pwm-leds"; - - greenled { - label = "green:mmc0"; - pwms = <&pwm 1 2000000 0>; - pwm-names = "pwm1"; - /* - * Green LED is much brighter than the others - * so limit its max brightness - */ - max_brightness = <127>; - linux,default-trigger = "mmc0"; - }; - - blueled { - label = "blue:heartbeat"; - pwms = <&pwm 2 2000000 0>; - pwm-names = "pwm2"; - max_brightness = <255>; - linux,default-trigger = "heartbeat"; - }; - }; - - gpioleds { - compatible = "gpio-leds"; - redled { - label = "red:microSD"; - gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>; - default-state = "off"; - linux,default-trigger = "mmc1"; - }; - }; - - sound: sound { - compatible = "simple-audio-card"; - - simple-audio-card,name = "Odroid-XU3"; - simple-audio-card,widgets = - "Headphone", "Headphone Jack", - "Speakers", "Speakers"; - simple-audio-card,routing = - "Headphone Jack", "HPL", - "Headphone Jack", "HPR", - "Headphone Jack", "MICBIAS", - "IN1", "Headphone Jack", - "Speakers", "SPKL", - "Speakers", "SPKR"; - - simple-audio-card,format = "i2s"; - simple-audio-card,bitclock-master = <&link0_codec>; - simple-audio-card,frame-master = <&link0_codec>; - - simple-audio-card,cpu { - sound-dai = <&i2s0 0>; - system-clock-frequency = <19200000>; - }; - - link0_codec: simple-audio-card,codec { - sound-dai = <&max98090>; - clocks = <&i2s0 CLK_I2S_CDCLK>; - }; + reset-gpios = <&gpd1 0 GPIO_ACTIVE_LOW>; }; fan0: pwm-fan { @@ -138,7 +74,7 @@ &hdmi { status = "okay"; - hpd-gpio = <&gpx3 7 0>; + hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&hdmi_hpd_irq>; @@ -160,6 +96,7 @@ s2mps11,buck2-ramp-enable = <1>; s2mps11,buck3-ramp-enable = <1>; s2mps11,buck4-ramp-enable = <1>; + samsung,s2mps11-acokb-ground; interrupt-parent = <&gpx0>; interrupts = <4 IRQ_TYPE_EDGE_FALLING>; @@ -375,19 +312,6 @@ }; }; -&hsi2c_5 { - status = "okay"; - max98090: max98090@10 { - compatible = "maxim,max98090"; - reg = <0x10>; - interrupt-parent = <&gpx3>; - interrupts = <2 0>; - clocks = <&i2s0 CLK_I2S_CDCLK>; - clock-names = "mclk"; - #sound-dai-cells = <0>; - }; -}; - &i2c_2 { samsung,i2c-sda-delay = <100>; samsung,i2c-max-bus-freq = <66000>; @@ -399,10 +323,6 @@ }; }; -&i2s0 { - status = "okay"; -}; - &mfc { samsung,mfc-r = <0x43000000 0x800000>; samsung,mfc-l = <0x51000000 0x800000>; @@ -463,18 +383,6 @@ }; }; -&pwm { - /* - * PWM 0 -- fan - * PWM 1 -- Green LED - * PWM 2 -- Blue LED - * PWM 3 -- on MIPI connector for backlight - */ - pinctrl-0 = <&pwm0_out &pwm1_out &pwm2_out &pwm3_out>; - pinctrl-names = "default"; - status = "okay"; -}; - &tmu_cpu0 { vtmu-supply = <&ldo7_reg>; status = "okay"; @@ -510,9 +418,7 @@ dr_mode = "host"; }; -&usbdrd_dwc3_1 { - dr_mode = "otg"; -}; +/* usbdrd_dwc3_1 mode customized in each board */ &usbdrd3_0 { vdd33-supply = <&ldo9_reg>; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts index c06882bbb822..b1b36081f343 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts @@ -13,8 +13,59 @@ /dts-v1/; #include "exynos5422-odroidxu3-common.dtsi" +#include "exynos5422-odroidxu3-audio.dtsi" / { model = "Hardkernel Odroid XU3 Lite"; compatible = "hardkernel,odroid-xu3-lite", "samsung,exynos5800", "samsung,exynos5"; + + pwmleds { + compatible = "pwm-leds"; + + greenled { + label = "green:mmc0"; + pwms = <&pwm 1 2000000 0>; + pwm-names = "pwm1"; + /* + * Green LED is much brighter than the others + * so limit its max brightness + */ + max_brightness = <127>; + linux,default-trigger = "mmc0"; + }; + + blueled { + label = "blue:heartbeat"; + pwms = <&pwm 2 2000000 0>; + pwm-names = "pwm2"; + max_brightness = <255>; + linux,default-trigger = "heartbeat"; + }; + }; + + gpioleds { + compatible = "gpio-leds"; + redled { + label = "red:microSD"; + gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>; + default-state = "off"; + linux,default-trigger = "mmc1"; + }; + }; +}; + +&pwm { + /* + * PWM 0 -- fan + * PWM 1 -- Green LED + * PWM 2 -- Blue LED + * PWM 3 -- on MIPI connector for backlight + */ + pinctrl-0 = <&pwm0_out &pwm1_out &pwm2_out &pwm3_out>; + pinctrl-names = "default"; + status = "okay"; +}; + +&usbdrd_dwc3_1 { + dr_mode = "otg"; }; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3.dts b/arch/arm/boot/dts/exynos5422-odroidxu3.dts index 78e6a502f320..0c0bbdbfd85f 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3.dts +++ b/arch/arm/boot/dts/exynos5422-odroidxu3.dts @@ -12,10 +12,45 @@ /dts-v1/; #include "exynos5422-odroidxu3-common.dtsi" +#include "exynos5422-odroidxu3-audio.dtsi" / { model = "Hardkernel Odroid XU3"; compatible = "hardkernel,odroid-xu3", "samsung,exynos5800", "samsung,exynos5"; + + pwmleds { + compatible = "pwm-leds"; + + greenled { + label = "green:mmc0"; + pwms = <&pwm 1 2000000 0>; + pwm-names = "pwm1"; + /* + * Green LED is much brighter than the others + * so limit its max brightness + */ + max_brightness = <127>; + linux,default-trigger = "mmc0"; + }; + + blueled { + label = "blue:heartbeat"; + pwms = <&pwm 2 2000000 0>; + pwm-names = "pwm2"; + max_brightness = <255>; + linux,default-trigger = "heartbeat"; + }; + }; + + gpioleds { + compatible = "gpio-leds"; + redled { + label = "red:microSD"; + gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>; + default-state = "off"; + linux,default-trigger = "mmc1"; + }; + }; }; &i2c_0 { @@ -49,3 +84,19 @@ shunt-resistor = <10000>; }; }; + +&pwm { + /* + * PWM 0 -- fan + * PWM 1 -- Green LED + * PWM 2 -- Blue LED + * PWM 3 -- on MIPI connector for backlight + */ + pinctrl-0 = <&pwm0_out &pwm1_out &pwm2_out &pwm3_out>; + pinctrl-names = "default"; + status = "okay"; +}; + +&usbdrd_dwc3_1 { + dr_mode = "otg"; +}; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu4.dts b/arch/arm/boot/dts/exynos5422-odroidxu4.dts new file mode 100644 index 000000000000..2faf88627a48 --- /dev/null +++ b/arch/arm/boot/dts/exynos5422-odroidxu4.dts @@ -0,0 +1,48 @@ +/* + * Hardkernel Odroid XU4 board device tree source + * + * Copyright (c) 2015 Krzysztof Kozlowski + * Copyright (c) 2014 Collabora Ltd. + * Copyright (c) 2013-2015 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/dts-v1/; +#include "exynos5422-odroidxu3-common.dtsi" + +/ { + model = "Hardkernel Odroid XU4"; + compatible = "hardkernel,odroid-xu4", "samsung,exynos5800", \ + "samsung,exynos5"; + + pwmleds { + compatible = "pwm-leds"; + + blueled { + label = "blue:heartbeat"; + pwms = <&pwm 2 2000000 0>; + pwm-names = "pwm2"; + max_brightness = <255>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&pwm { + /* + * PWM 0 -- fan + * PWM 2 -- Blue LED + */ + pinctrl-0 = <&pwm0_out &pwm2_out>; + pinctrl-names = "default"; + samsung,pwm-outputs = <0>, <2>; + status = "okay"; +}; + +&usbdrd_dwc3_1 { + dr_mode = "host"; +}; diff --git a/arch/arm/boot/dts/exynos5440-ssdk5440.dts b/arch/arm/boot/dts/exynos5440-ssdk5440.dts index e4443f4e6572..6a0d802e87c8 100644 --- a/arch/arm/boot/dts/exynos5440-ssdk5440.dts +++ b/arch/arm/boot/dts/exynos5440-ssdk5440.dts @@ -11,6 +11,7 @@ /dts-v1/; #include "exynos5440.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "SAMSUNG SSDK5440 board based on EXYNOS5440"; @@ -29,12 +30,12 @@ }; &pcie_0 { - reset-gpio = <&pin_ctrl 5 0>; + reset-gpio = <&pin_ctrl 5 GPIO_ACTIVE_HIGH>; status = "okay"; }; &pcie_1 { - reset-gpio = <&pin_ctrl 22 0>; + reset-gpio = <&pin_ctrl 22 GPIO_ACTIVE_HIGH>; status = "okay"; }; diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts index 8f40c7e549bd..49a4f43e5ac2 100644 --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts @@ -94,7 +94,7 @@ regulator-name = "P5.0V_USB3CON0"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - gpio = <&gph0 0 0>; + gpio = <&gph0 0 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&usb300_vbus_en>; enable-active-high; @@ -105,7 +105,7 @@ regulator-name = "P5.0V_USB3CON1"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - gpio = <&gph0 1 0>; + gpio = <&gph0 1 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&usb301_vbus_en>; enable-active-high; @@ -147,7 +147,7 @@ samsung,color-depth = <1>; samsung,link-rate = <0x0a>; samsung,lane-count = <2>; - samsung,hpd-gpio = <&gpx2 6 0>; + samsung,hpd-gpio = <&gpx2 6 GPIO_ACTIVE_HIGH>; panel = <&panel>; }; @@ -893,7 +893,7 @@ status = "okay"; num-cs = <1>; samsung,spi-src-clk = <0>; - cs-gpios = <&gpb1 2 0>; + cs-gpios = <&gpb1 2 GPIO_ACTIVE_HIGH>; cros_ec: cros-ec@0 { compatible = "google,cros-ec-spi"; @@ -903,6 +903,7 @@ pinctrl-0 = <&ec_spi_cs &ec_irq>; reg = <0>; spi-max-frequency = <3125000>; + google,has-vbc-nvram; controller-data { samsung,spi-feedback-delay = <1>; diff --git a/arch/arm/boot/dts/hi3620-hi4511.dts b/arch/arm/boot/dts/hi3620-hi4511.dts index fe623928f687..a579fbf13b5f 100644 --- a/arch/arm/boot/dts/hi3620-hi4511.dts +++ b/arch/arm/boot/dts/hi3620-hi4511.dts @@ -16,7 +16,8 @@ compatible = "hisilicon,hi3620-hi4511"; chosen { - bootargs = "console=ttyAMA0,115200 root=/dev/ram0 earlyprintk"; + bootargs = "root=/dev/ram0"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/hisi-x5hd2-dkb.dts b/arch/arm/boot/dts/hisi-x5hd2-dkb.dts index 721b09238f58..d13af8437d10 100644 --- a/arch/arm/boot/dts/hisi-x5hd2-dkb.dts +++ b/arch/arm/boot/dts/hisi-x5hd2-dkb.dts @@ -15,7 +15,7 @@ compatible = "hisilicon,hix5hd2"; chosen { - bootargs = "console=ttyAMA0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; cpus { diff --git a/arch/arm/boot/dts/imx23.dtsi b/arch/arm/boot/dts/imx23.dtsi index b995333ea22b..1c6c07538a78 100644 --- a/arch/arm/boot/dts/imx23.dtsi +++ b/arch/arm/boot/dts/imx23.dtsi @@ -383,9 +383,11 @@ }; ocotp@8002c000 { - compatible = "fsl,ocotp"; + compatible = "fsl,imx23-ocotp", "fsl,ocotp"; + #address-cells = <1>; + #size-cells = <1>; reg = <0x8002c000 0x2000>; - status = "disabled"; + clocks = <&clks 15>; }; axi-ahb@8002e000 { diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts index 279249b8c3f3..e3ef94ac159f 100644 --- a/arch/arm/boot/dts/imx28-evk.dts +++ b/arch/arm/boot/dts/imx28-evk.dts @@ -57,7 +57,7 @@ flash: m25p80@0 { #address-cells = <1>; #size-cells = <1>; - compatible = "sst,sst25vf016b"; + compatible = "sst,sst25vf016b", "jedec,spi-nor"; spi-max-frequency = <40000000>; reg = <0>; }; diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts index e35cc6ba3ca6..8d04e57039bc 100644 --- a/arch/arm/boot/dts/imx28-m28evk.dts +++ b/arch/arm/boot/dts/imx28-m28evk.dts @@ -41,7 +41,7 @@ flash: m25p80@0 { #address-cells = <1>; #size-cells = <1>; - compatible = "m25p80"; + compatible = "m25p80", "jedec,spi-nor"; spi-max-frequency = <40000000>; reg = <0>; }; diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index 4e073e854742..c5b57d4adade 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -936,9 +936,11 @@ }; ocotp: ocotp@8002c000 { - compatible = "fsl,ocotp"; + compatible = "fsl,imx28-ocotp", "fsl,ocotp"; + #address-cells = <1>; + #size-cells = <1>; reg = <0x8002c000 0x2000>; - status = "disabled"; + clocks = <&clks 25>; }; axi-ahb@8002e000 { diff --git a/arch/arm/boot/dts/imx31.dtsi b/arch/arm/boot/dts/imx31.dtsi index c34f82581248..5fdb222636a7 100644 --- a/arch/arm/boot/dts/imx31.dtsi +++ b/arch/arm/boot/dts/imx31.dtsi @@ -25,7 +25,7 @@ #size-cells = <0>; cpu { - compatible = "arm,arm1136"; + compatible = "arm,arm1136jf-s"; device_type = "cpu"; }; }; diff --git a/arch/arm/boot/dts/imx35.dtsi b/arch/arm/boot/dts/imx35.dtsi index e6540b5cfa4c..ed3dc3391d1c 100644 --- a/arch/arm/boot/dts/imx35.dtsi +++ b/arch/arm/boot/dts/imx35.dtsi @@ -29,7 +29,7 @@ #size-cells = <0>; cpu { - compatible = "arm,arm1136"; + compatible = "arm,arm1136jf-s"; device_type = "cpu"; }; }; diff --git a/arch/arm/boot/dts/imx50-evk.dts b/arch/arm/boot/dts/imx50-evk.dts index 1b22512c91bd..27d763c7a307 100644 --- a/arch/arm/boot/dts/imx50-evk.dts +++ b/arch/arm/boot/dts/imx50-evk.dts @@ -33,7 +33,7 @@ flash: m25p32@1 { #address-cells = <1>; #size-cells = <1>; - compatible = "m25p32", "m25p80"; + compatible = "m25p32", "jedec,spi-nor"; spi-max-frequency = <25000000>; reg = <1>; diff --git a/arch/arm/boot/dts/imx53-smd.dts b/arch/arm/boot/dts/imx53-smd.dts index fc89ce1e5763..542ab9e697fb 100644 --- a/arch/arm/boot/dts/imx53-smd.dts +++ b/arch/arm/boot/dts/imx53-smd.dts @@ -76,7 +76,7 @@ flash: m25p32@1 { #address-cells = <1>; #size-cells = <1>; - compatible = "st,m25p32", "st,m25p"; + compatible = "st,m25p32", "st,m25p", "jedec,spi-nor"; spi-max-frequency = <20000000>; reg = <1>; diff --git a/arch/arm/boot/dts/imx6dl-nit6xlite.dts b/arch/arm/boot/dts/imx6dl-nit6xlite.dts new file mode 100644 index 000000000000..e0161e46195c --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-nit6xlite.dts @@ -0,0 +1,49 @@ +/* + * Copyright 2015 Boundary Devices, Inc. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +/dts-v1/; + +#include "imx6dl.dtsi" +#include "imx6qdl-nit6xlite.dtsi" + +/ { + model = "Boundary Devices i.MX6 Solo Nitrogen6_Lite Board"; + compatible = "boundary,imx6dl-nit6xlite", "fsl,imx6dl"; +}; diff --git a/arch/arm/boot/dts/imx6dl-nitrogen6x.dts b/arch/arm/boot/dts/imx6dl-nitrogen6x.dts index 5f4d33ccc4b3..8398f979b912 100644 --- a/arch/arm/boot/dts/imx6dl-nitrogen6x.dts +++ b/arch/arm/boot/dts/imx6dl-nitrogen6x.dts @@ -3,12 +3,42 @@ * Copyright 2012 Freescale Semiconductor, Inc. * Copyright 2011 Linaro Ltd. * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. */ /dts-v1/; @@ -16,6 +46,6 @@ #include "imx6qdl-nitrogen6x.dtsi" / { - model = "Freescale i.MX6 DualLite Nitrogen6x Board"; - compatible = "fsl,imx6dl-nitrogen6x", "fsl,imx6dl"; + model = "Boundary Devices i.MX6 DualLite Nitrogen6x Board"; + compatible = "boundary,imx6dl-nitrogen6x", "fsl,imx6dl"; }; diff --git a/arch/arm/boot/dts/imx6dl-rex-basic.dts b/arch/arm/boot/dts/imx6dl-rex-basic.dts index b13845c2823b..c3a14a4330a2 100644 --- a/arch/arm/boot/dts/imx6dl-rex-basic.dts +++ b/arch/arm/boot/dts/imx6dl-rex-basic.dts @@ -23,7 +23,7 @@ &ecspi3 { flash: m25p80@0 { - compatible = "sst,sst25vf016b"; + compatible = "sst,sst25vf016b", "jedec,spi-nor"; spi-max-frequency = <20000000>; reg = <0>; }; diff --git a/arch/arm/boot/dts/imx6dl-sabrelite.dts b/arch/arm/boot/dts/imx6dl-sabrelite.dts index 2de04479dc35..0f06ca5c9146 100644 --- a/arch/arm/boot/dts/imx6dl-sabrelite.dts +++ b/arch/arm/boot/dts/imx6dl-sabrelite.dts @@ -2,12 +2,42 @@ * Copyright 2011 Freescale Semiconductor, Inc. * Copyright 2011 Linaro Ltd. * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. */ /dts-v1/; diff --git a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts index 4fa254347798..364578d707a5 100644 --- a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts +++ b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts @@ -109,7 +109,7 @@ status = "okay"; flash: m25p80@0 { - compatible = "m25p80"; + compatible = "m25p80", "jedec,spi-nor"; spi-max-frequency = <40000000>; reg = <0>; }; diff --git a/arch/arm/boot/dts/imx6q-gw5400-a.dts b/arch/arm/boot/dts/imx6q-gw5400-a.dts index 822ffb231c57..58adf176425a 100644 --- a/arch/arm/boot/dts/imx6q-gw5400-a.dts +++ b/arch/arm/boot/dts/imx6q-gw5400-a.dts @@ -145,7 +145,7 @@ status = "okay"; flash: m25p80@0 { - compatible = "sst,w25q256"; + compatible = "sst,w25q256", "jedec,spi-nor"; spi-max-frequency = <30000000>; reg = <0>; }; diff --git a/arch/arm/boot/dts/imx6q-nitrogen6_max.dts b/arch/arm/boot/dts/imx6q-nitrogen6_max.dts new file mode 100644 index 000000000000..d417457ca6db --- /dev/null +++ b/arch/arm/boot/dts/imx6q-nitrogen6_max.dts @@ -0,0 +1,53 @@ +/* + * Copyright 2015 Boundary Devices, Inc. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +/dts-v1/; + +#include "imx6q.dtsi" +#include "imx6qdl-nitrogen6_max.dtsi" + +/ { + model = "Boundary Devices i.MX6 Quad Nitrogen6_MAX Board"; + compatible = "boundary,imx6q-nitrogen6_max", "fsl,imx6q"; +}; + +&sata { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6q-nitrogen6x.dts b/arch/arm/boot/dts/imx6q-nitrogen6x.dts index a57866b2e97e..d1686339dc48 100644 --- a/arch/arm/boot/dts/imx6q-nitrogen6x.dts +++ b/arch/arm/boot/dts/imx6q-nitrogen6x.dts @@ -3,12 +3,42 @@ * Copyright 2012 Freescale Semiconductor, Inc. * Copyright 2011 Linaro Ltd. * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. */ /dts-v1/; @@ -16,8 +46,8 @@ #include "imx6qdl-nitrogen6x.dtsi" / { - model = "Freescale i.MX6 Quad Nitrogen6x Board"; - compatible = "fsl,imx6q-nitrogen6x", "fsl,imx6q"; + model = "Boundary Devices i.MX6 Quad Nitrogen6x Board"; + compatible = "boundary,imx6q-nitrogen6x", "fsl,imx6q"; }; &sata { diff --git a/arch/arm/boot/dts/imx6q-rex-pro.dts b/arch/arm/boot/dts/imx6q-rex-pro.dts index 3c2852b16f78..90ea61ae04e9 100644 --- a/arch/arm/boot/dts/imx6q-rex-pro.dts +++ b/arch/arm/boot/dts/imx6q-rex-pro.dts @@ -23,7 +23,7 @@ &ecspi3 { flash: m25p80@0 { - compatible = "sst,sst25vf032b"; + compatible = "sst,sst25vf032b", "jedec,spi-nor"; spi-max-frequency = <20000000>; reg = <0>; }; diff --git a/arch/arm/boot/dts/imx6q-sabrelite.dts b/arch/arm/boot/dts/imx6q-sabrelite.dts index 96e4688be77c..66d10d8d534c 100644 --- a/arch/arm/boot/dts/imx6q-sabrelite.dts +++ b/arch/arm/boot/dts/imx6q-sabrelite.dts @@ -2,12 +2,42 @@ * Copyright 2011 Freescale Semiconductor, Inc. * Copyright 2011 Linaro Ltd. * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. */ /dts-v1/; diff --git a/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi b/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi index f4d6ae564ead..ecbc6eba6a2c 100644 --- a/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi +++ b/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi @@ -109,7 +109,7 @@ flash: m25p80@0 { #address-cells = <1>; #size-cells = <1>; - compatible = "micron,n25q128a11"; + compatible = "micron,n25q128a11", "jedec,spi-nor"; spi-max-frequency = <20000000>; reg = <0>; }; diff --git a/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi b/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi index a47a0399a172..7d81100e7d47 100644 --- a/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi +++ b/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi @@ -141,7 +141,7 @@ flash: m25p80@1 { #address-cells = <1>; #size-cells = <1>; - compatible = "micron,n25q128a11"; + compatible = "micron,n25q128a11", "jedec,spi-nor"; spi-max-frequency = <20000000>; reg = <1>; }; diff --git a/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi b/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi index 45e7c39e80d5..da1341d47b14 100644 --- a/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi +++ b/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi @@ -38,7 +38,7 @@ flash: m25p80@0 { #address-cells = <1>; #size-cells = <1>; - compatible = "sst,sst25vf040b", "m25p80"; + compatible = "sst,sst25vf040b", "jedec,spi-nor"; spi-max-frequency = <20000000>; reg = <0>; }; diff --git a/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi b/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi new file mode 100644 index 000000000000..24d7d3f18464 --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi @@ -0,0 +1,630 @@ +/* + * Copyright 2015 Boundary Devices, Inc. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + chosen { + stdout-path = &uart2; + }; + + memory { + reg = <0x10000000 0x20000000>; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_2p5v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "2P5V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + reg_3p3v: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_usb_otg_vbus: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_wlan_vmmc: regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wlan_vmmc>; + regulator-name = "reg_wlan_vmmc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio6 7 GPIO_ACTIVE_HIGH>; + startup-delay-us = <70000>; + enable-active-high; + }; + }; + + bt_rfkill { + compatible = "rfkill-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_bt_rfkill>; + gpios = <&gpio6 8 GPIO_ACTIVE_HIGH>; + name = "bt_rfkill"; + type = <2>; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_keys>; + + home { + label = "Home"; + gpios = <&gpio7 13 IRQ_TYPE_LEVEL_LOW>; + linux,code = <102>; + }; + + back { + label = "Back"; + gpios = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>; + linux,code = <158>; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + + j14-pin1 { + gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; + retain-state-suspended; + default-state = "off"; + }; + + j14-pin3 { + gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; + retain-state-suspended; + default-state = "off"; + }; + + j14-pins8-9 { + gpios = <&gpio3 29 GPIO_ACTIVE_LOW>; + retain-state-suspended; + default-state = "off"; + }; + + j46-pin2 { + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + retain-state-suspended; + default-state = "off"; + }; + + j46-pin3 { + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + retain-state-suspended; + default-state = "off"; + }; + }; + + backlight_lcd { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + power-supply = <®_3p3v>; + status = "okay"; + }; + + backlight_lvds0: backlight_lvds0 { + compatible = "pwm-backlight"; + pwms = <&pwm4 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + power-supply = <®_3p3v>; + status = "okay"; + }; + + panel_lvds0 { + compatible = "hannstar,hsd100pxn1"; + backlight = <&backlight_lvds0>; + + port { + panel_in_lvds0: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; + }; + + sound { + compatible = "fsl,imx6dl-nit6xlite-sgtl5000", + "fsl,imx-audio-sgtl5000"; + model = "imx6dl-nit6xlite-sgtl5000"; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + mux-int-port = <1>; + mux-ext-port = <3>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; +}; + +&clks { + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, + <&clks IMX6QDL_CLK_LDB_DI1_SEL>; + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>, + <&clks IMX6QDL_CLK_PLL3_USB_OTG>; +}; + +&ecspi1 { + fsl,spi-num-chipselects = <1>; + cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + flash: m25p80@0 { + compatible = "microchip,sst25vf016b"; + spi-max-frequency = <20000000>; + reg = <0>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>; + txen-skew-ps = <0>; + txc-skew-ps = <3000>; + rxdv-skew-ps = <0>; + rxc-skew-ps = <3000>; + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txd0-skew-ps = <0>; + txd1-skew-ps = <0>; + txd2-skew-ps = <0>; + txd3-skew-ps = <0>; + interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>, + <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>; + status = "okay"; +}; + +&hdmi { + ddc-i2c-bus = <&i2c2>; + status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + codec: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sgtl5000>; + reg = <0x0a>; + clocks = <&clks 201>; + VDDA-supply = <®_2p5v>; + VDDIO-supply = <®_3p3v>; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + touchscreen@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + interrupt-parent = <&gpio1>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; + wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + }; + + touchscreen@38 { + compatible = "edt,edt-ft5x06"; + reg = <0x38>; + interrupt-parent = <&gpio1>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; + }; + + rtc@6f { + compatible = "isil,isl1208"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rtc>; + reg = <0x6f>; + interrupts-extended = <&gpio2 26 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_j10>; + pinctrl-1 = <&pinctrl_j28>; + + imx6dl-nit6xlite { + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 + >; + }; + + pinctrl_bt_rfkill: bt_rfkillgrp { + fsl,pins = < + /* BT wake */ + MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0 + /* BT reset */ + MX6QDL_PAD_NANDF_ALE__GPIO6_IO08 0x0b0b0 + /* BT reg en */ + MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0 + /* BT host wake irq */ + MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x100b0 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x100b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x100b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x100b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x100b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x100b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x100b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x100b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + /* Phy reset */ + MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x0f0b0 + MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0 + MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1 + >; + }; + + pinctrl_gpio_keys: gpio_keysgrp { + fsl,pins = < + /* Home Button: J14 pin 5 */ + MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b0b0 + /* Back Button: J14 pin 7 */ + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1 + /* Touch IRQ: J7 pin 4 */ + MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0 + /* tcs2004 IRQ */ + MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x1b0b0 + /* tsc2004 reset */ + MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x0b0b0 + >; + }; + + pinctrl_j10: j10grp { + fsl,pins = < + /* Broadcom WiFi module pins */ + MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0 + MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0 + MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0 + MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0 + MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x0b0b0 + MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x1b0b0 + MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT 0x000b0 + >; + }; + + pinctrl_j28: j28grp { + fsl,pins = < + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0 + >; + }; + + pinctrl_leds: ledsgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x0b0b0 + MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x0b0b0 + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x030b0 + MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x0b0b0 + MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x0b0b0 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm4: pwm4grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1 + >; + }; + + pinctrl_wlan_vmmc: wlan_vmmcgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x030b0 + >; + }; + + pinctrl_rtc: rtcgrp { + fsl,pins = < + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x1b0b0 + >; + }; + + pinctrl_sgtl5000: sgtl5000grp { + fsl,pins = < + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000b0 + MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1 + MX6QDL_PAD_EIM_D31__UART3_RTS_B 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0 + /* power enable, high active */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x000b0 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0 + >; + }; + }; +}; + +&ldb { + status = "okay"; + + lvds-channel@0 { + fsl,data-mapping = "spwg"; + fsl,data-width = <18>; + status = "okay"; + + port@4 { + reg = <4>; + + lvds0_out: endpoint { + remote-endpoint = <&panel_in_lvds0>; + }; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; + status = "okay"; +}; + +&pwm4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm4>; + status = "okay"; +}; + +&ssi1 { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + fsl,uart-has-rtscts; + status = "okay"; +}; + +&usbh1 { + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + bus-width = <4>; + non-removable; + vmmc-supply = <®_3p3v>; + vqmmc-supply = <®_wlan_vmmc>; + vqmmc-1-8-v; + ocr-limit = <0x180>; /* 1.65v - 2.1v */ + cap-power-off-card; + keep-power-in-suspend; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi b/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi new file mode 100644 index 000000000000..a35d54fd9cd3 --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi @@ -0,0 +1,873 @@ +/* + * Copyright 2015 Boundary Devices, Inc. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + chosen { + stdout-path = &uart2; + }; + + memory { + reg = <0x10000000 0xF0000000>; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_1p8v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "1P8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + reg_2p5v: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "2P5V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + reg_3p3v: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_usb_otg_vbus: regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb_h1_vbus: regulator@4 { + compatible = "regulator-fixed"; + reg = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1>; + regulator-name = "usb_h1_vbus"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_wlan_vmmc: regulator@5 { + compatible = "regulator-fixed"; + reg = <5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wlan_vmmc>; + regulator-name = "reg_wlan_vmmc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio6 15 GPIO_ACTIVE_HIGH>; + startup-delay-us = <70000>; + enable-active-high; + }; + + reg_can_xcvr: regulator@6 { + compatible = "regulator-fixed"; + reg = <6>; + regulator-name = "CAN XCVR"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can_xcvr>; + gpio = <&gpio1 2 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_keys>; + + power { + label = "Power Button"; + gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + gpio-key,wakeup; + }; + + menu { + label = "Menu"; + gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; + linux,code = <KEY_MENU>; + }; + + home { + label = "Home"; + gpios = <&gpio2 4 GPIO_ACTIVE_LOW>; + linux,code = <KEY_HOME>; + }; + + back { + label = "Back"; + gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; + linux,code = <KEY_BACK>; + }; + + volume-up { + label = "Volume Up"; + gpios = <&gpio7 13 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + + volume-down { + label = "Volume Down"; + gpios = <&gpio7 1 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEDOWN>; + }; + }; + + i2cmux@2 { + compatible = "i2c-mux-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2mux>; + #address-cells = <1>; + #size-cells = <0>; + mux-gpios = <&gpio3 20 GPIO_ACTIVE_HIGH + &gpio4 15 GPIO_ACTIVE_HIGH>; + i2c-parent = <&i2c2>; + idle-state = <0>; + + i2c2@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c2@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + i2cmux@3 { + compatible = "i2c-mux-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3mux>; + #address-cells = <1>; + #size-cells = <0>; + mux-gpios = <&gpio2 25 GPIO_ACTIVE_HIGH>; + i2c-parent = <&i2c3>; + idle-state = <0>; + + i2c3@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + leds { + compatible = "gpio-leds"; + + speaker-enable { + gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>; + retain-state-suspended; + default-state = "off"; + }; + + ttymxc4-rs232 { + gpios = <&gpio6 10 GPIO_ACTIVE_HIGH>; + retain-state-suspended; + default-state = "on"; + }; + }; + + backlight_lcd: backlight_lcd { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + power-supply = <®_3p3v>; + status = "okay"; + }; + + backlight_lvds0: backlight_lvds0 { + compatible = "pwm-backlight"; + pwms = <&pwm4 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + power-supply = <®_3p3v>; + status = "okay"; + }; + + backlight_lvds1: backlight_lvds1 { + compatible = "pwm-backlight"; + pwms = <&pwm2 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + power-supply = <®_3p3v>; + status = "okay"; + }; + + lcd_display: display@di0 { + compatible = "fsl,imx-parallel-display"; + #address-cells = <1>; + #size-cells = <0>; + interface-pix-fmt = "bgr666"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_j15>; + status = "okay"; + + port@0 { + reg = <0>; + + lcd_display_in: endpoint { + remote-endpoint = <&ipu1_di0_disp0>; + }; + }; + + port@1 { + reg = <1>; + + lcd_display_out: endpoint { + remote-endpoint = <&lcd_panel_in>; + }; + }; + }; + + panel_lcd { + compatible = "okaya,rs800480t-7x0gp"; + backlight = <&backlight_lcd>; + + port { + lcd_panel_in: endpoint { + remote-endpoint = <&lcd_display_out>; + }; + }; + }; + + panel_lvds0 { + compatible = "hannstar,hsd100pxn1"; + backlight = <&backlight_lvds0>; + + port { + panel_in_lvds0: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; + }; + + panel_lvds1 { + compatible = "hannstar,hsd100pxn1"; + backlight = <&backlight_lvds1>; + + port { + panel_in_lvds1: endpoint { + remote-endpoint = <&lvds1_out>; + }; + }; + }; + + sound { + compatible = "fsl,imx6q-nitrogen6_max-sgtl5000", + "fsl,imx-audio-sgtl5000"; + model = "imx6q-nitrogen6_max-sgtl5000"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sgtl5000>; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + mux-int-port = <1>; + mux-ext-port = <3>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can1>; + xceiver-supply = <®_can_xcvr>; + status = "okay"; +}; + +&clks { + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, + <&clks IMX6QDL_CLK_LDB_DI1_SEL>; + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>, + <&clks IMX6QDL_CLK_PLL3_USB_OTG>; +}; + +&ecspi1 { + fsl,spi-num-chipselects = <1>; + cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + flash: m25p80@0 { + compatible = "microchip,sst25vf016b"; + spi-max-frequency = <20000000>; + reg = <0>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>; + txen-skew-ps = <0>; + txc-skew-ps = <3000>; + rxdv-skew-ps = <0>; + rxc-skew-ps = <3000>; + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txd0-skew-ps = <0>; + txd1-skew-ps = <0>; + txd2-skew-ps = <0>; + txd3-skew-ps = <0>; + interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>, + <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>; + status = "okay"; +}; + +&hdmi { + ddc-i2c-bus = <&i2c2>; + status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + codec: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + clocks = <&clks 201>; + VDDA-supply = <®_2p5v>; + VDDIO-supply = <®_3p3v>; + }; + + rtc: rtc@68 { + compatible = "st,rv4162"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rv4162>; + reg = <0x68>; + interrupts-extended = <&gpio4 6 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + touchscreen@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + interrupt-parent = <&gpio1>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; + wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + }; + + touchscreen@38 { + compatible = "edt,edt-ft5x06"; + reg = <0x38>; + interrupt-parent = <&gpio1>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; + }; +}; + +&iomuxc { + imx6q-nitrogen6_max { + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 + >; + }; + + pinctrl_can1: can1grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b0b0 + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b0b0 + >; + }; + + pinctrl_can_xcvr: can-xcvrgrp { + fsl,pins = < + /* Flexcan XCVR enable */ + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x100b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x100b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x100b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x100b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x100b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x100b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x100b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + /* Phy reset */ + MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x0f0b0 + MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0 + MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1 + >; + }; + + pinctrl_gpio_keys: gpio_keysgrp { + fsl,pins = < + /* Power Button */ + MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0 + /* Menu Button */ + MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0 + /* Home Button */ + MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0 + /* Back Button */ + MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0 + /* Volume Up Button */ + MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b0b0 + /* Volume Down Button */ + MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1b0b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c2mux: i2c2muxgrp { + fsl,pins = < + /* ov5642 camera i2c enable */ + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x000b0 + /* ov5640_mipi camera i2c enable */ + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1 + MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0 + >; + }; + + pinctrl_i2c3mux: i2c3muxgrp { + fsl,pins = < + /* PCIe I2C enable */ + MX6QDL_PAD_EIM_OE__GPIO2_IO25 0x000b0 + >; + }; + + pinctrl_j15: j15grp { + fsl,pins = < + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10 + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10 + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10 + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10 + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10 + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10 + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10 + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10 + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10 + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10 + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10 + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10 + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10 + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10 + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10 + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10 + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10 + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10 + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10 + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10 + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10 + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10 + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10 + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10 + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10 + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10 + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10 + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10 + >; + }; + + pinctrl_pcie: pciegrp { + fsl,pins = < + /* PCIe reset */ + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x000b0 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm2: pwm2grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm4: pwm4grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1 + >; + }; + + pinctrl_rv4162: rv4162grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0 + >; + }; + + pinctrl_sgtl5000: sgtl5000grp { + fsl,pins = < + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000b0 + MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b0 + MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x130b1 + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x030b1 + /* RS485 RX Enable: pull up */ + MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x1b0b1 + /* RS485 DEN: pull down */ + MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x030b1 + /* RS485/!RS232 Select: pull down (rs232) */ + MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x030b1 + /* ON: pull down */ + MX6QDL_PAD_NANDF_ALE__GPIO6_IO08 0x030b1 + >; + }; + + pinctrl_usbh1: usbh1grp { + fsl,pins = < + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x0b0b0 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0 + /* power enable, high active */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x000b0 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x100b0 + MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0 + >; + }; + + pinctrl_usdhc4: usdhc4grp { + fsl,pins = < + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059 + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059 + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059 + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059 + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059 + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059 + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059 + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059 + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059 + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059 + >; + }; + + pinctrl_wlan_vmmc: wlan_vmmcgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x100b0 + MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x000b0 + MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x000b0 + MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT 0x000b0 + >; + }; + }; +}; + +&ipu1_di0_disp0 { + remote-endpoint = <&lcd_display_in>; +}; + +&ldb { + status = "okay"; + + lvds-channel@0 { + fsl,data-mapping = "spwg"; + fsl,data-width = <18>; + status = "okay"; + + port@4 { + reg = <4>; + + lvds0_out: endpoint { + remote-endpoint = <&panel_in_lvds0>; + }; + }; + }; + + lvds-channel@1 { + fsl,data-mapping = "spwg"; + fsl,data-width = <18>; + status = "okay"; + + port@4 { + reg = <4>; + + lvds1_out: endpoint { + remote-endpoint = <&panel_in_lvds1>; + }; + }; + }; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie>; + reset-gpio = <&gpio6 31 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&pwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2>; + status = "okay"; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; + status = "okay"; +}; + +&pwm4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm4>; + status = "okay"; +}; + +&ssi1 { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5>; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usb_h1_vbus>; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + bus-width = <4>; + non-removable; + vmmc-supply = <®_wlan_vmmc>; + cap-power-off-card; + keep-power-in-suspend; + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1271"; + reg = <2>; + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; + ref-clock-frequency = <38400000>; + }; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; + +&usdhc4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc4>; + bus-width = <8>; + non-removable; + vmmc-supply = <®_1p8v>; + keep-power-in-suspend; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi b/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi index 340bc8e42650..caeed56b74a3 100644 --- a/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi +++ b/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi @@ -3,12 +3,42 @@ * Copyright 2011 Freescale Semiconductor, Inc. * Copyright 2011 Linaro Ltd. * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. */ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> @@ -65,6 +95,19 @@ pinctrl-0 = <&pinctrl_can_xcvr>; gpio = <&gpio1 2 GPIO_ACTIVE_LOW>; }; + + reg_wlan_vmmc: regulator@4 { + compatible = "regulator-fixed"; + reg = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wlan_vmmc>; + regulator-name = "reg_wlan_vmmc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio6 15 GPIO_ACTIVE_HIGH>; + startup-delay-us = <70000>; + enable-active-high; + }; }; gpio-keys { @@ -124,7 +167,7 @@ mux-ext-port = <3>; }; - backlight_lcd { + backlight_lcd: backlight_lcd { compatible = "pwm-backlight"; pwms = <&pwm1 0 5000000>; brightness-levels = <0 4 8 16 32 64 128 255>; @@ -142,6 +185,43 @@ status = "okay"; }; + lcd_display: display@di0 { + compatible = "fsl,imx-parallel-display"; + #address-cells = <1>; + #size-cells = <0>; + interface-pix-fmt = "bgr666"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_j15>; + status = "okay"; + + port@0 { + reg = <0>; + + lcd_display_in: endpoint { + remote-endpoint = <&ipu1_di0_disp0>; + }; + }; + + port@1 { + reg = <1>; + + lcd_display_out: endpoint { + remote-endpoint = <&lcd_panel_in>; + }; + }; + }; + + lcd_panel { + compatible = "okaya,rs800480t-7x0gp"; + backlight = <&backlight_lcd>; + + port { + lcd_panel_in: endpoint { + remote-endpoint = <&lcd_display_out>; + }; + }; + }; + panel { compatible = "hannstar,hsd100pxn1"; backlight = <&backlight_lvds>; @@ -182,7 +262,7 @@ status = "okay"; flash: m25p80@0 { - compatible = "sst,sst25vf016b"; + compatible = "sst,sst25vf016b", "jedec,spi-nor"; spi-max-frequency = <20000000>; reg = <0>; }; @@ -247,6 +327,21 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c3>; status = "okay"; + + touchscreen@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + interrupt-parent = <&gpio1>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; + wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + }; + + touchscreen@38 { + compatible = "edt,edt-ft5x06"; + reg = <0x38>; + interrupt-parent = <&gpio1>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; + }; }; &iomuxc { @@ -258,6 +353,7 @@ fsl,pins = < /* SGTL5000 sys_mclk */ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x030b0 + MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0 >; }; @@ -354,6 +450,39 @@ >; }; + pinctrl_j15: j15grp { + fsl,pins = < + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10 + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10 + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10 + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10 + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10 + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10 + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10 + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10 + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10 + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10 + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10 + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10 + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10 + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10 + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10 + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10 + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10 + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10 + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10 + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10 + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10 + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10 + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10 + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10 + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10 + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10 + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10 + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10 + >; + }; + pinctrl_pwm1: pwm1grp { fsl,pins = < MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1 @@ -395,6 +524,18 @@ >; }; + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17071 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10071 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17071 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17071 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17071 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17071 + MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x000b0 + >; + }; + pinctrl_usdhc3: usdhc3grp { fsl,pins = < MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 @@ -418,9 +559,22 @@ MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x1b0b0 /* CD */ >; }; + + pinctrl_wlan_vmmc: wlan_vmmcgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x100b0 + MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x000b0 + MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x000b0 + MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT 0x000b0 + >; + }; }; }; +&ipu1_di0_disp0 { + remote-endpoint = <&lcd_display_in>; +}; + &ldb { status = "okay"; @@ -489,6 +643,27 @@ status = "okay"; }; +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + bus-width = <4>; + non-removable; + vmmc-supply = <®_wlan_vmmc>; + cap-power-off-card; + keep-power-in-suspend; + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1271"; + reg = <2>; + interrupt-parent = <&gpio6>; + interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; + ref-clock-frequency = <38400000>; + }; +}; + &usdhc3 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usdhc3>; diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi index 9e6ecd99b472..d6d98d426384 100644 --- a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi +++ b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi @@ -12,7 +12,7 @@ #include <dt-bindings/gpio/gpio.h> / { - model = "Phytec phyFLEX-i.MX6 Ouad"; + model = "Phytec phyFLEX-i.MX6 Quad"; compatible = "phytec,imx6q-pfla02", "fsl,imx6q"; memory { @@ -80,7 +80,7 @@ cs-gpios = <&gpio4 24 0>; flash@0 { - compatible = "m25p80"; + compatible = "m25p80", "jedec,spi-nor"; spi-max-frequency = <20000000>; reg = <0>; }; @@ -373,7 +373,7 @@ }; &pcie { - pinctrl-name = "default"; + pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie>; reset-gpio = <&gpio4 17 0>; status = "disabled"; diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi index c37bb9ff9fac..8263fc18a7d9 100644 --- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi +++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi @@ -133,7 +133,7 @@ flash: m25p80@0 { #address-cells = <1>; #size-cells = <1>; - compatible = "st,m25p32"; + compatible = "st,m25p32", "jedec,spi-nor"; spi-max-frequency = <20000000>; reg = <0>; }; diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi index ce4c7313f509..1a69a3420ac8 100644 --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi @@ -2,12 +2,42 @@ * Copyright 2011 Freescale Semiconductor, Inc. * Copyright 2011 Linaro Ltd. * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. */ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> @@ -123,7 +153,7 @@ mux-ext-port = <4>; }; - backlight_lcd { + backlight_lcd: backlight_lcd { compatible = "pwm-backlight"; pwms = <&pwm1 0 5000000>; brightness-levels = <0 4 8 16 32 64 128 255>; @@ -141,6 +171,43 @@ status = "okay"; }; + lcd_display: display@di0 { + compatible = "fsl,imx-parallel-display"; + #address-cells = <1>; + #size-cells = <0>; + interface-pix-fmt = "bgr666"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_j15>; + status = "okay"; + + port@0 { + reg = <0>; + + lcd_display_in: endpoint { + remote-endpoint = <&ipu1_di0_disp0>; + }; + }; + + port@1 { + reg = <1>; + + lcd_display_out: endpoint { + remote-endpoint = <&lcd_panel_in>; + }; + }; + }; + + lcd_panel { + compatible = "okaya,rs800480t-7x0gp"; + backlight = <&backlight_lcd>; + + port { + lcd_panel_in: endpoint { + remote-endpoint = <&lcd_display_out>; + }; + }; + }; + panel { compatible = "hannstar,hsd100pxn1"; backlight = <&backlight_lvds>; @@ -181,7 +248,7 @@ status = "okay"; flash: m25p80@0 { - compatible = "sst,sst25vf016b"; + compatible = "sst,sst25vf016b", "jedec,spi-nor"; spi-max-frequency = <20000000>; reg = <0>; }; @@ -348,6 +415,39 @@ >; }; + pinctrl_j15: j15grp { + fsl,pins = < + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10 + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10 + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10 + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10 + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10 + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10 + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10 + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10 + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10 + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10 + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10 + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10 + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10 + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10 + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10 + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10 + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10 + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10 + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10 + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10 + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10 + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10 + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10 + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10 + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10 + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10 + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10 + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10 + >; + }; + pinctrl_pwm1: pwm1grp { fsl,pins = < MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1 @@ -416,6 +516,10 @@ }; }; +&ipu1_di0_disp0 { + remote-endpoint = <&lcd_display_in>; +}; + &ldb { status = "okay"; diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi index 2c07d3a86b61..a6d445c17779 100644 --- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi +++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi @@ -158,7 +158,7 @@ flash: m25p80@0 { #address-cells = <1>; #size-cells = <1>; - compatible = "st,m25p32"; + compatible = "st,m25p32", "jedec,spi-nor"; spi-max-frequency = <20000000>; reg = <0>; }; diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index e716e6f301c6..2b6cc8bf3c5c 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -218,16 +218,16 @@ dmas = <&sdma 14 18 0>, <&sdma 15 18 0>; dma-names = "rx", "tx"; - clocks = <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_OSC>, - <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_DUMMY>, - <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, - <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, - <&clks IMX6QDL_CLK_DUMMY>; + clocks = <&clks IMX6QDL_CLK_SPDIF_GCLK>, <&clks IMX6QDL_CLK_OSC>, + <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_ASRC>, + <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_ESAI_EXTAL>, + <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_MLB>, + <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_SPBA>; clock-names = "core", "rxtx0", "rxtx1", "rxtx2", "rxtx3", "rxtx4", "rxtx5", "rxtx6", - "rxtx7"; + "rxtx7", "dma"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts index b84dff2e94ea..be118820e9f7 100644 --- a/arch/arm/boot/dts/imx6sl-evk.dts +++ b/arch/arm/boot/dts/imx6sl-evk.dts @@ -126,7 +126,7 @@ flash: m25p80@0 { #address-cells = <1>; #size-cells = <1>; - compatible = "st,m25p32"; + compatible = "st,m25p32", "jedec,spi-nor"; spi-max-frequency = <20000000>; reg = <0>; }; diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi index 320a27f8889e..d8ba99f1d87b 100644 --- a/arch/arm/boot/dts/imx6sl.dtsi +++ b/arch/arm/boot/dts/imx6sl.dtsi @@ -135,8 +135,24 @@ ranges; spdif: spdif@02004000 { + compatible = "fsl,imx6sl-spdif", + "fsl,imx35-spdif"; reg = <0x02004000 0x4000>; interrupts = <0 52 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&sdma 14 18 0>, + <&sdma 15 18 0>; + dma-names = "rx", "tx"; + clocks = <&clks IMX6SL_CLK_SPDIF_GCLK>, <&clks IMX6SL_CLK_OSC>, + <&clks IMX6SL_CLK_SPDIF>, <&clks IMX6SL_CLK_DUMMY>, + <&clks IMX6SL_CLK_DUMMY>, <&clks IMX6SL_CLK_DUMMY>, + <&clks IMX6SL_CLK_IPG>, <&clks IMX6SL_CLK_DUMMY>, + <&clks IMX6SL_CLK_DUMMY>, <&clks IMX6SL_CLK_SPBA>; + clock-names = "core", "rxtx0", + "rxtx1", "rxtx2", + "rxtx3", "rxtx4", + "rxtx5", "rxtx6", + "rxtx7", "dma"; + status = "disabled"; }; ecspi1: ecspi@02008000 { @@ -670,8 +686,11 @@ }; dcp: dcp@020fc000 { + compatible = "fsl,imx6sl-dcp", "fsl,imx28-dcp"; reg = <0x020fc000 0x4000>; - interrupts = <0 99 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <0 99 IRQ_TYPE_LEVEL_HIGH>, + <0 100 IRQ_TYPE_LEVEL_HIGH>, + <0 101 IRQ_TYPE_LEVEL_HIGH>; }; }; diff --git a/arch/arm/boot/dts/imx6sx-sdb-reva.dts b/arch/arm/boot/dts/imx6sx-sdb-reva.dts index c76b87cba275..71005478cdf0 100644 --- a/arch/arm/boot/dts/imx6sx-sdb-reva.dts +++ b/arch/arm/boot/dts/imx6sx-sdb-reva.dts @@ -129,7 +129,7 @@ reg = <0>; #address-cells = <1>; #size-cells = <1>; - compatible = "spansion,s25fl128s"; + compatible = "spansion,s25fl128s", "jedec,spi-nor"; spi-max-frequency = <66000000>; }; @@ -137,7 +137,7 @@ reg = <1>; #address-cells = <1>; #size-cells = <1>; - compatible = "spansion,s25fl128s"; + compatible = "spansion,s25fl128s", "jedec,spi-nor"; spi-max-frequency = <66000000>; }; }; diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts b/arch/arm/boot/dts/imx6sx-sdb.dts index 0bfc4e7865b2..0ad164ab5729 100644 --- a/arch/arm/boot/dts/imx6sx-sdb.dts +++ b/arch/arm/boot/dts/imx6sx-sdb.dts @@ -130,7 +130,7 @@ flash0: n25q256a@0 { #address-cells = <1>; #size-cells = <1>; - compatible = "micron,n25q256a"; + compatible = "micron,n25q256a", "jedec,spi-nor"; spi-max-frequency = <29000000>; reg = <0>; }; @@ -138,7 +138,7 @@ flash1: n25q256a@1 { #address-cells = <1>; #size-cells = <1>; - compatible = "micron,n25q256a"; + compatible = "micron,n25q256a", "jedec,spi-nor"; spi-max-frequency = <29000000>; reg = <1>; }; diff --git a/arch/arm/boot/dts/imx6sx-sdb.dtsi b/arch/arm/boot/dts/imx6sx-sdb.dtsi index ac88c3467078..94ac4005d9cd 100644 --- a/arch/arm/boot/dts/imx6sx-sdb.dtsi +++ b/arch/arm/boot/dts/imx6sx-sdb.dtsi @@ -114,7 +114,7 @@ regulator-name = "peri_3v3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>; + gpio = <&gpio4 16 GPIO_ACTIVE_HIGH>; enable-active-high; regulator-always-on; }; diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi index c94f2ea2316e..167f77b3bd43 100644 --- a/arch/arm/boot/dts/imx6sx.dtsi +++ b/arch/arm/boot/dts/imx6sx.dtsi @@ -211,7 +211,7 @@ dmas = <&sdma 14 18 0>, <&sdma 15 18 0>; dma-names = "rx", "tx"; - clocks = <&clks IMX6SX_CLK_SPDIF>, + clocks = <&clks IMX6SX_CLK_SPDIF_GCLK>, <&clks IMX6SX_CLK_OSC>, <&clks IMX6SX_CLK_SPDIF>, <&clks 0>, <&clks 0>, <&clks 0>, diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dts b/arch/arm/boot/dts/imx6ul-14x14-evk.dts index 25746b122ea6..6aaa5ec3d846 100644 --- a/arch/arm/boot/dts/imx6ul-14x14-evk.dts +++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dts @@ -87,6 +87,19 @@ }; }; +&snvs_poweroff { + status = "okay"; +}; + +&tsc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tsc>; + xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; + measure-delay-time = <0xffff>; + pre-charge-time = <0xfff>; + status = "okay"; +}; + &uart1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1>; @@ -277,6 +290,15 @@ >; }; + pinctrl_tsc: tscgrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0xb0 + MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0 + MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0 + MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0xb0 + >; + }; + pinctrl_uart1: uart1grp { fsl,pins = < MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1 diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi index 09edbedfd908..d00e994bdbd2 100644 --- a/arch/arm/boot/dts/imx6ul.dtsi +++ b/arch/arm/boot/dts/imx6ul.dtsi @@ -135,6 +135,11 @@ status = "disabled"; }; + ocram: sram@00900000 { + compatible = "mmio-sram"; + reg = <0x00900000 0x20000>; + }; + aips1: aips-bus@02000000 { compatible = "fsl,aips-bus", "simple-bus"; #address-cells = <1>; @@ -424,6 +429,14 @@ <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; }; + snvs_poweroff: snvs-poweroff { + compatible = "syscon-poweroff"; + regmap = <&snvs>; + offset = <0x38>; + mask = <0x60>; + status = "disabled"; + }; + snvs_pwrkey: snvs-powerkey { compatible = "fsl,sec-v4.0-pwrkey"; regmap = <&snvs>; @@ -571,6 +584,17 @@ status = "disabled"; }; + tsc: tsc@02040000 { + compatible = "fsl,imx6ul-tsc"; + reg = <0x02040000 0x4000>, <0x0219c000 0x4000>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6UL_CLK_IPG>, + <&clks IMX6UL_CLK_ADC2>; + clock-names = "tsc", "adc"; + status = "disabled"; + }; + usdhc1: usdhc@02190000 { compatible = "fsl,imx6ul-usdhc", "fsl,imx6sx-usdhc"; reg = <0x02190000 0x4000>; @@ -625,6 +649,11 @@ status = "disabled"; }; + mmdc: mmdc@021b0000 { + compatible = "fsl,imx6ul-mmdc", "fsl,imx6q-mmdc"; + reg = <0x021b0000 0x4000>; + }; + qspi: qspi@021e0000 { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/imx7d-pinfunc.h b/arch/arm/boot/dts/imx7d-pinfunc.h index a8d81497edb3..eeda78347619 100644 --- a/arch/arm/boot/dts/imx7d-pinfunc.h +++ b/arch/arm/boot/dts/imx7d-pinfunc.h @@ -15,6 +15,122 @@ * <mux_reg conf_reg input_reg mux_mode input_val> */ +#define MX7D_PAD_GPIO1_IO00__GPIO1_IO0 0x0000 0x0030 0x0000 0x0 0x0 +#define MX7D_PAD_GPIO1_IO00__PWM4_OUT 0x0000 0x0030 0x0000 0x1 0x0 +#define MX7D_PAD_GPIO1_IO00__WDOD1_WDOG_ANY 0x0000 0x0030 0x0000 0x2 0x0 +#define MX7D_PAD_GPIO1_IO00__WDOD1_WDOG_B 0x0000 0x0030 0x0000 0x3 0x0 +#define MX7D_PAD_GPIO1_IO00__WDOD1_WDOG__RST_B_DEB 0x0000 0x0030 0x0000 0x4 0x0 +#define MX7D_PAD_GPIO1_IO01__GPIO1_IO1 0x0004 0x0034 0x0000 0x0 0x0 +#define MX7D_PAD_GPIO1_IO01__PWM1_OUT 0x0004 0x0034 0x0000 0x1 0x0 +#define MX7D_PAD_GPIO1_IO01__CCM_ENET_REF_CLK3 0x0004 0x0034 0x0000 0x2 0x0 +#define MX7D_PAD_GPIO1_IO01__SAI1_MCLK 0x0004 0x0034 0x0000 0x3 0x0 +#define MX7D_PAD_GPIO1_IO01__ANATOP_24M_OUT 0x0004 0x0034 0x0000 0x4 0x0 +#define MX7D_PAD_GPIO1_IO01__OBSERVE0_OUT 0x0004 0x0034 0x0000 0x6 0x0 +#define MX7D_PAD_GPIO1_IO02__GPIO1_IO2 0x0008 0x0038 0x0000 0x0 0x0 +#define MX7D_PAD_GPIO1_IO02__PWM2_OUT 0x0008 0x0038 0x0000 0x1 0x0 +#define MX7D_PAD_GPIO1_IO02__CCM_ENET_REF_CLK1 0x0008 0x0038 0x0564 0x2 0x3 +#define MX7D_PAD_GPIO1_IO02__SAI2_MCLK 0x0008 0x0038 0x0000 0x3 0x0 +#define MX7D_PAD_GPIO1_IO02__CCM_CLKO1 0x0008 0x0038 0x0000 0x5 0x0 +#define MX7D_PAD_GPIO1_IO02__OBSERVE1_OUT 0x0008 0x0038 0x0000 0x6 0x0 +#define MX7D_PAD_GPIO1_IO02__USB_OTG1_ID 0x0008 0x0038 0x0734 0x7 0x3 +#define MX7D_PAD_GPIO1_IO03__GPIO1_IO3 0x000C 0x003C 0x0000 0x0 0x0 +#define MX7D_PAD_GPIO1_IO03__PWM3_OUT 0x000C 0x003C 0x0000 0x1 0x0 +#define MX7D_PAD_GPIO1_IO03__CCM_ENET_REF_CLK2 0x000C 0x003C 0x0570 0x2 0x3 +#define MX7D_PAD_GPIO1_IO03__SAI3_MCLK 0x000C 0x003C 0x0000 0x3 0x0 +#define MX7D_PAD_GPIO1_IO03__CCM_CLKO2 0x000C 0x003C 0x0000 0x5 0x0 +#define MX7D_PAD_GPIO1_IO03__OBSERVE2_OUT 0x000C 0x003C 0x0000 0x6 0x0 +#define MX7D_PAD_GPIO1_IO03__USB_OTG2_ID 0x000C 0x003C 0x0730 0x7 0x3 +#define MX7D_PAD_GPIO1_IO04__GPIO1_IO4 0x0010 0x0040 0x0000 0x0 0x0 +#define MX7D_PAD_GPIO1_IO04__USB_OTG1_OC 0x0010 0x0040 0x072C 0x1 0x1 +#define MX7D_PAD_GPIO1_IO04__FLEXTIMER1_CH4 0x0010 0x0040 0x0594 0x2 0x1 +#define MX7D_PAD_GPIO1_IO04__UART5_CTS_B 0x0010 0x0040 0x0710 0x3 0x4 +#define MX7D_PAD_GPIO1_IO04__I2C1_SCL 0x0010 0x0040 0x05D4 0x4 0x2 +#define MX7D_PAD_GPIO1_IO04__OBSERVE3_OUT 0x0010 0x0040 0x0000 0x6 0x0 +#define MX7D_PAD_GPIO1_IO05__GPIO1_IO5 0x0014 0x0044 0x0000 0x0 0x0 +#define MX7D_PAD_GPIO1_IO05__USB_OTG1_PWR 0x0014 0x0044 0x0000 0x1 0x0 +#define MX7D_PAD_GPIO1_IO05__FLEXTIMER1_CH5 0x0014 0x0044 0x0598 0x2 0x1 +#define MX7D_PAD_GPIO1_IO05__UART5_RTS_B 0x0014 0x0044 0x0710 0x3 0x5 +#define MX7D_PAD_GPIO1_IO05__I2C1_SDA 0x0014 0x0044 0x05D8 0x4 0x2 +#define MX7D_PAD_GPIO1_IO05__OBSERVE4_OUT 0x0014 0x0044 0x0000 0x6 0x0 +#define MX7D_PAD_GPIO1_IO06__GPIO1_IO6 0x0018 0x0048 0x0000 0x0 0x0 +#define MX7D_PAD_GPIO1_IO06__USB_OTG2_OC 0x0018 0x0048 0x0728 0x1 0x1 +#define MX7D_PAD_GPIO1_IO06__FLEXTIMER1_CH6 0x0018 0x0048 0x059C 0x2 0x1 +#define MX7D_PAD_GPIO1_IO06__UART5_RX_DATA 0x0018 0x0048 0x0714 0x3 0x4 +#define MX7D_PAD_GPIO1_IO06__I2C2_SCL 0x0018 0x0048 0x05DC 0x4 0x2 +#define MX7D_PAD_GPIO1_IO06__CCM_WAIT 0x0018 0x0048 0x0000 0x5 0x0 +#define MX7D_PAD_GPIO1_IO06__KPP_ROW4 0x0018 0x0048 0x0624 0x6 0x1 +#define MX7D_PAD_GPIO1_IO07__GPIO1_IO7 0x001C 0x004C 0x0000 0x0 0x0 +#define MX7D_PAD_GPIO1_IO07__USB_OTG2_PWR 0x001C 0x004C 0x0000 0x1 0x0 +#define MX7D_PAD_GPIO1_IO07__FLEXTIMER1_CH7 0x001C 0x004C 0x05A0 0x2 0x1 +#define MX7D_PAD_GPIO1_IO07__UART5_TX_DATA 0x001C 0x004C 0x0714 0x3 0x5 +#define MX7D_PAD_GPIO1_IO07__I2C2_SDA 0x001C 0x004C 0x05E0 0x4 0x2 +#define MX7D_PAD_GPIO1_IO07__CCM_STOP 0x001C 0x004C 0x0000 0x5 0x0 +#define MX7D_PAD_GPIO1_IO07__KPP_COL4 0x001C 0x004C 0x0604 0x6 0x1 +#define MX7D_PAD_GPIO1_IO08__GPIO1_IO8 0x0014 0x026C 0x0000 0x0 0x0 +#define MX7D_PAD_GPIO1_IO08__SD1_VSELECT 0x0014 0x026C 0x0000 0x1 0x0 +#define MX7D_PAD_GPIO1_IO08__WDOG1_WDOG_B 0x0014 0x026C 0x0000 0x2 0x0 +#define MX7D_PAD_GPIO1_IO08__UART3_DCE_RX 0x0014 0x026C 0x0704 0x3 0x0 +#define MX7D_PAD_GPIO1_IO08__UART3_DTE_TX 0x0014 0x026C 0x0000 0x3 0x0 +#define MX7D_PAD_GPIO1_IO08__I2C3_SCL 0x0014 0x026C 0x05E4 0x4 0x0 +#define MX7D_PAD_GPIO1_IO08__KPP_COL5 0x0014 0x026C 0x0608 0x6 0x0 +#define MX7D_PAD_GPIO1_IO08__PWM1_OUT 0x0014 0x026C 0x0000 0x7 0x0 +#define MX7D_PAD_GPIO1_IO09__GPIO1_IO9 0x0018 0x0270 0x0000 0x0 0x0 +#define MX7D_PAD_GPIO1_IO09__SD1_LCTL 0x0018 0x0270 0x0000 0x1 0x0 +#define MX7D_PAD_GPIO1_IO09__CCM_ENET_REF_CLK3 0x0018 0x0270 0x0000 0x2 0x0 +#define MX7D_PAD_GPIO1_IO09__UART3_DCE_TX 0x0018 0x0270 0x0000 0x3 0x0 +#define MX7D_PAD_GPIO1_IO09__UART3_DTE_RX 0x0018 0x0270 0x0704 0x3 0x1 +#define MX7D_PAD_GPIO1_IO09__I2C3_SDA 0x0018 0x0270 0x05E8 0x4 0x0 +#define MX7D_PAD_GPIO1_IO09__CCM_PMIC_READY 0x0018 0x0270 0x04F4 0x5 0x0 +#define MX7D_PAD_GPIO1_IO09__KPP_ROW5 0x0018 0x0270 0x0628 0x6 0x0 +#define MX7D_PAD_GPIO1_IO09__PWM2_OUT 0x0018 0x0270 0x0000 0x7 0x0 +#define MX7D_PAD_GPIO1_IO10__GPIO1_IO10 0x001C 0x0274 0x0000 0x0 0x0 +#define MX7D_PAD_GPIO1_IO10__SD2_LCTL 0x001C 0x0274 0x0000 0x1 0x0 +#define MX7D_PAD_GPIO1_IO10__ENET1_MDIO 0x001C 0x0274 0x0568 0x2 0x0 +#define MX7D_PAD_GPIO1_IO10__UART3_DCE_RTS 0x001C 0x0274 0x0700 0x3 0x0 +#define MX7D_PAD_GPIO1_IO10__UART3_DTE_CTS 0x001C 0x0274 0x0000 0x3 0x0 +#define MX7D_PAD_GPIO1_IO10__I2C4_SCL 0x001C 0x0274 0x05EC 0x4 0x0 +#define MX7D_PAD_GPIO1_IO10__FLEXTIMER1_PHA 0x001C 0x0274 0x05A4 0x5 0x0 +#define MX7D_PAD_GPIO1_IO10__KPP_COL6 0x001C 0x0274 0x060C 0x6 0x0 +#define MX7D_PAD_GPIO1_IO10__PWM3_OUT 0x001C 0x0274 0x0000 0x7 0x0 +#define MX7D_PAD_GPIO1_IO11__GPIO1_IO11 0x0020 0x0278 0x0000 0x0 0x0 +#define MX7D_PAD_GPIO1_IO11__SD3_LCTL 0x0020 0x0278 0x0000 0x1 0x0 +#define MX7D_PAD_GPIO1_IO11__ENET1_MDC 0x0020 0x0278 0x0000 0x2 0x0 +#define MX7D_PAD_GPIO1_IO11__UART3_DCE_CTS 0x0020 0x0278 0x0000 0x3 0x0 +#define MX7D_PAD_GPIO1_IO11__UART3_DTE_RTS 0x0020 0x0278 0x0700 0x3 0x1 +#define MX7D_PAD_GPIO1_IO11__I2C4_SDA 0x0020 0x0278 0x05F0 0x4 0x0 +#define MX7D_PAD_GPIO1_IO11__FLEXTIMER1_PHB 0x0020 0x0278 0x05A8 0x5 0x0 +#define MX7D_PAD_GPIO1_IO11__KPP_ROW6 0x0020 0x0278 0x062C 0x6 0x0 +#define MX7D_PAD_GPIO1_IO11__PWM4_OUT 0x0020 0x0278 0x0000 0x7 0x0 +#define MX7D_PAD_GPIO1_IO12__GPIO1_IO12 0x0024 0x027C 0x0000 0x0 0x0 +#define MX7D_PAD_GPIO1_IO12__SD2_VSELECT 0x0024 0x027C 0x0000 0x1 0x0 +#define MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1 0x0024 0x027C 0x0564 0x2 0x0 +#define MX7D_PAD_GPIO1_IO12__FLEXCAN1_RX 0x0024 0x027C 0x04DC 0x3 0x0 +#define MX7D_PAD_GPIO1_IO12__CM4_NMI 0x0024 0x027C 0x0000 0x4 0x0 +#define MX7D_PAD_GPIO1_IO12__CCM_EXT_CLK1 0x0024 0x027C 0x04E4 0x5 0x0 +#define MX7D_PAD_GPIO1_IO12__SNVS_VIO_5 0x0024 0x027C 0x0000 0x6 0x0 +#define MX7D_PAD_GPIO1_IO12__USB_OTG1_ID 0x0024 0x027C 0x0734 0x7 0x0 +#define MX7D_PAD_GPIO1_IO13__GPIO1_IO13 0x0028 0x0280 0x0000 0x0 0x0 +#define MX7D_PAD_GPIO1_IO13__SD3_VSELECT 0x0028 0x0280 0x0000 0x1 0x0 +#define MX7D_PAD_GPIO1_IO13__CCM_ENET_REF_CLK2 0x0028 0x0280 0x0570 0x2 0x0 +#define MX7D_PAD_GPIO1_IO13__FLEXCAN1_TX 0x0028 0x0280 0x0000 0x3 0x0 +#define MX7D_PAD_GPIO1_IO13__CCM_PMIC_READY 0x0028 0x0280 0x04F4 0x4 0x1 +#define MX7D_PAD_GPIO1_IO13__CCM_EXT_CLK2 0x0028 0x0280 0x04E8 0x5 0x0 +#define MX7D_PAD_GPIO1_IO13__SNVS_VIO_5_CTL 0x0028 0x0280 0x0000 0x6 0x0 +#define MX7D_PAD_GPIO1_IO13__USB_OTG2_ID 0x0028 0x0280 0x0730 0x7 0x0 +#define MX7D_PAD_GPIO1_IO14__GPIO1_IO14 0x002C 0x0284 0x0000 0x0 0x0 +#define MX7D_PAD_GPIO1_IO14__SD3_CD_B 0x002C 0x0284 0x0738 0x1 0x0 +#define MX7D_PAD_GPIO1_IO14__ENET2_MDIO 0x002C 0x0284 0x0574 0x2 0x0 +#define MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX 0x002C 0x0284 0x04E0 0x3 0x0 +#define MX7D_PAD_GPIO1_IO14__WDOG3_WDOG_B 0x002C 0x0284 0x0000 0x4 0x0 +#define MX7D_PAD_GPIO1_IO14__CCM_EXT_CLK3 0x002C 0x0284 0x04EC 0x5 0x0 +#define MX7D_PAD_GPIO1_IO14__SDMA_EXT_EVENT0 0x002C 0x0284 0x06D8 0x6 0x0 +#define MX7D_PAD_GPIO1_IO15__GPIO1_IO15 0x0030 0x0288 0x0000 0x0 0x0 +#define MX7D_PAD_GPIO1_IO15__SD3_WP 0x0030 0x0288 0x073C 0x1 0x0 +#define MX7D_PAD_GPIO1_IO15__ENET2_MDC 0x0030 0x0288 0x0000 0x2 0x0 +#define MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX 0x0030 0x0288 0x0000 0x3 0x0 +#define MX7D_PAD_GPIO1_IO15__WDOG4_WDOG_B 0x0030 0x0288 0x0000 0x4 0x0 +#define MX7D_PAD_GPIO1_IO15__CCM_EXT_CLK4 0x0030 0x0288 0x04F0 0x5 0x0 +#define MX7D_PAD_GPIO1_IO15__SDMA_EXT_EVENT1 0x0030 0x0288 0x06DC 0x6 0x0 #define MX7D_PAD_EPDC_DATA00__EPDC_DATA0 0x0034 0x02A4 0x0000 0x0 0x0 #define MX7D_PAD_EPDC_DATA00__SIM1_PORT2_TRXD 0x0034 0x02A4 0x0000 0x1 0x0 #define MX7D_PAD_EPDC_DATA00__QSPI_A_DATA0 0x0034 0x02A4 0x0000 0x2 0x0 @@ -453,7 +569,7 @@ #define MX7D_PAD_LCD_DATA23__EIM_ADDR26 0x0124 0x0394 0x0000 0x4 0x0 #define MX7D_PAD_LCD_DATA23__GPIO3_IO28 0x0124 0x0394 0x0000 0x5 0x0 #define MX7D_PAD_LCD_DATA23__I2C4_SDA 0x0124 0x0394 0x05F0 0x6 0x1 -#define MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX 0x0128 0x0398 0x0000 0x0 0x0 +#define MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX 0x0128 0x0398 0x06F4 0x0 0x0 #define MX7D_PAD_UART1_RX_DATA__UART1_DTE_TX 0x0128 0x0398 0x0000 0x0 0x0 #define MX7D_PAD_UART1_RX_DATA__I2C1_SCL 0x0128 0x0398 0x05D4 0x1 0x0 #define MX7D_PAD_UART1_RX_DATA__CCM_PMIC_READY 0x0128 0x0398 0x0000 0x2 0x0 @@ -469,7 +585,7 @@ #define MX7D_PAD_UART1_TX_DATA__ENET2_1588_EVENT0_OUT 0x012C 0x039C 0x0000 0x4 0x0 #define MX7D_PAD_UART1_TX_DATA__GPIO4_IO1 0x012C 0x039C 0x0000 0x5 0x0 #define MX7D_PAD_UART1_TX_DATA__ENET1_MDC 0x012C 0x039C 0x0000 0x6 0x0 -#define MX7D_PAD_UART2_RX_DATA__UART2_DCE_RX 0x0130 0x03A0 0x0000 0x0 0x0 +#define MX7D_PAD_UART2_RX_DATA__UART2_DCE_RX 0x0130 0x03A0 0x06FC 0x0 0x2 #define MX7D_PAD_UART2_RX_DATA__UART2_DTE_TX 0x0130 0x03A0 0x0000 0x0 0x0 #define MX7D_PAD_UART2_RX_DATA__I2C2_SCL 0x0130 0x03A0 0x05DC 0x1 0x0 #define MX7D_PAD_UART2_RX_DATA__SAI3_RX_BCLK 0x0130 0x03A0 0x0000 0x2 0x0 @@ -501,7 +617,7 @@ #define MX7D_PAD_UART3_TX_DATA__ENET1_1588_EVENT0_OUT 0x013C 0x03AC 0x0000 0x4 0x0 #define MX7D_PAD_UART3_TX_DATA__GPIO4_IO5 0x013C 0x03AC 0x0000 0x5 0x0 #define MX7D_PAD_UART3_TX_DATA__SD2_LCTL 0x013C 0x03AC 0x0000 0x6 0x0 -#define MX7D_PAD_UART3_RTS_B__UART3_DCE_RTS 0x0140 0x03B0 0x0000 0x0 0x0 +#define MX7D_PAD_UART3_RTS_B__UART3_DCE_RTS 0x0140 0x03B0 0x0700 0x0 0x2 #define MX7D_PAD_UART3_RTS_B__UART3_DTE_CTS 0x0140 0x03B0 0x0000 0x0 0x0 #define MX7D_PAD_UART3_RTS_B__USB_OTG2_OC 0x0140 0x03B0 0x0728 0x1 0x0 #define MX7D_PAD_UART3_RTS_B__SAI3_TX_DATA0 0x0140 0x03B0 0x0000 0x2 0x0 diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts index fdd1d7c9a5cc..432aaf5d5ef7 100644 --- a/arch/arm/boot/dts/imx7d-sdb.dts +++ b/arch/arm/boot/dts/imx7d-sdb.dts @@ -101,6 +101,45 @@ arm-supply = <&sw1a_reg>; }; +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1>; + assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>, + <&clks IMX7D_ENET1_TIME_ROOT_CLK>; + assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>; + assigned-clock-rates = <0>, <100000000>; + phy-mode = "rgmii"; + phy-handle = <ðphy0>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; + + ethphy1: ethernet-phy@1 { + reg = <1>; + }; + }; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2>; + assigned-clocks = <&clks IMX7D_ENET2_TIME_ROOT_SRC>, + <&clks IMX7D_ENET2_TIME_ROOT_CLK>; + assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>; + assigned-clock-rates = <0>, <100000000>; + phy-mode = "rgmii"; + phy-handle = <ðphy1>; + fsl,magic-packet; + status = "okay"; +}; + &i2c1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c1>; @@ -231,6 +270,17 @@ status = "okay"; }; +&usbotg1 { + vbus-supply = <®_usb_otg1_vbus>; + status = "okay"; +}; + +&usbotg2 { + vbus-supply = <®_usb_otg2_vbus>; + dr_mode = "host"; + status = "okay"; +}; + &usdhc1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usdhc1>; @@ -241,11 +291,60 @@ status = "okay"; }; +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>; + assigned-clock-rates = <400000000>; + bus-width = <8>; + fsl,tuning-step = <2>; + non-removable; + status = "okay"; +}; + &iomuxc { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hog>; imx7d-sdb { + pinctrl_enet1: enet1grp { + fsl,pins = < + MX7D_PAD_GPIO1_IO10__ENET1_MDIO 0x3 + MX7D_PAD_GPIO1_IO11__ENET1_MDC 0x3 + MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC 0x1 + MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 0x1 + MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 0x1 + MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2 0x1 + MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3 0x1 + MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x1 + MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC 0x1 + MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 0x1 + MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 0x1 + MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2 0x1 + MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3 0x1 + MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x1 + >; + }; + + pinctrl_enet2: enet2grp { + fsl,pins = < + MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC 0x1 + MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0 0x1 + MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1 0x1 + MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2 0x1 + MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3 0x1 + MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL 0x1 + MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC 0x1 + MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0 0x1 + MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1 0x1 + MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2 0x1 + MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3 0x1 + MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL 0x1 + >; + }; + pinctrl_hog: hoggrp { fsl,pins = < MX7D_PAD_UART3_CTS_B__GPIO4_IO7 0x14 @@ -281,7 +380,6 @@ >; }; - pinctrl_uart1: uart1grp { fsl,pins = < MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX 0x79 diff --git a/arch/arm/boot/dts/imx7d.dtsi b/arch/arm/boot/dts/imx7d.dtsi index 6e444bb873f9..ebc053a06405 100644 --- a/arch/arm/boot/dts/imx7d.dtsi +++ b/arch/arm/boot/dts/imx7d.dtsi @@ -446,6 +446,12 @@ status = "disabled"; }; + iomuxc_lpsr: iomuxc-lpsr@302c0000 { + compatible = "fsl,imx7d-iomuxc-lpsr"; + reg = <0x302c0000 0x10000>; + fsl,input-sel = <&iomuxc>; + }; + gpt1: gpt@302d0000 { compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt"; reg = <0x302d0000 0x10000>; @@ -570,6 +576,58 @@ }; }; + aips2: aips-bus@30400000 { + compatible = "fsl,aips-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x30400000 0x400000>; + ranges; + + pwm1: pwm@30660000 { + compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm"; + reg = <0x30660000 0x10000>; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_PWM1_ROOT_CLK>, + <&clks IMX7D_PWM1_ROOT_CLK>; + clock-names = "ipg", "per"; + #pwm-cells = <2>; + status = "disabled"; + }; + + pwm2: pwm@30670000 { + compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm"; + reg = <0x30670000 0x10000>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_PWM2_ROOT_CLK>, + <&clks IMX7D_PWM2_ROOT_CLK>; + clock-names = "ipg", "per"; + #pwm-cells = <2>; + status = "disabled"; + }; + + pwm3: pwm@30680000 { + compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm"; + reg = <0x30680000 0x10000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_PWM3_ROOT_CLK>, + <&clks IMX7D_PWM3_ROOT_CLK>; + clock-names = "ipg", "per"; + #pwm-cells = <2>; + status = "disabled"; + }; + + pwm4: pwm@30690000 { + compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm"; + reg = <0x30690000 0x10000>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_PWM4_ROOT_CLK>, + <&clks IMX7D_PWM4_ROOT_CLK>; + clock-names = "ipg", "per"; + #pwm-cells = <2>; + status = "disabled"; + }; + }; + aips3: aips-bus@30800000 { compatible = "fsl,aips-bus", "simple-bus"; #address-cells = <1>; @@ -694,6 +752,77 @@ status = "disabled"; }; + usbotg1: usb@30b10000 { + compatible = "fsl,imx7d-usb", "fsl,imx27-usb"; + reg = <0x30b10000 0x200>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_USB_CTRL_CLK>; + fsl,usbphy = <&usbphynop1>; + fsl,usbmisc = <&usbmisc1 0>; + phy-clkgate-delay-us = <400>; + status = "disabled"; + }; + + usbotg2: usb@30b20000 { + compatible = "fsl,imx7d-usb", "fsl,imx27-usb"; + reg = <0x30b20000 0x200>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_USB_CTRL_CLK>; + fsl,usbphy = <&usbphynop2>; + fsl,usbmisc = <&usbmisc2 0>; + phy-clkgate-delay-us = <400>; + status = "disabled"; + }; + + usbh: usb@30b30000 { + compatible = "fsl,imx7d-usb", "fsl,imx27-usb"; + reg = <0x30b30000 0x200>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_USB_CTRL_CLK>; + fsl,usbphy = <&usbphynop3>; + fsl,usbmisc = <&usbmisc3 0>; + phy_type = "hsic"; + dr_mode = "host"; + phy-clkgate-delay-us = <400>; + status = "disabled"; + }; + + usbmisc1: usbmisc@30b10200 { + #index-cells = <1>; + compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc"; + reg = <0x30b10200 0x200>; + }; + + usbmisc2: usbmisc@30b20200 { + #index-cells = <1>; + compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc"; + reg = <0x30b20200 0x200>; + }; + + usbmisc3: usbmisc@30b30200 { + #index-cells = <1>; + compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc"; + reg = <0x30b30200 0x200>; + }; + + usbphynop1: usbphynop1 { + compatible = "usb-nop-xceiv"; + clocks = <&clks IMX7D_USB_PHY1_CLK>; + clock-names = "main_clk"; + }; + + usbphynop2: usbphynop2 { + compatible = "usb-nop-xceiv"; + clocks = <&clks IMX7D_USB_PHY2_CLK>; + clock-names = "main_clk"; + }; + + usbphynop3: usbphynop3 { + compatible = "usb-nop-xceiv"; + clocks = <&clks IMX7D_USB_HSIC_ROOT_CLK>; + clock-names = "main_clk"; + }; + usdhc1: usdhc@30b40000 { compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc"; reg = <0x30b40000 0x10000>; @@ -729,6 +858,42 @@ bus-width = <4>; status = "disabled"; }; + + fec1: ethernet@30be0000 { + compatible = "fsl,imx7d-fec", "fsl,imx6sx-fec"; + reg = <0x30be0000 0x10000>; + interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>, + <&clks IMX7D_ENET_AXI_ROOT_CLK>, + <&clks IMX7D_ENET1_TIME_ROOT_CLK>, + <&clks IMX7D_PLL_ENET_MAIN_125M_CLK>, + <&clks IMX7D_ENET_PHY_REF_ROOT_CLK>; + clock-names = "ipg", "ahb", "ptp", + "enet_clk_ref", "enet_out"; + fsl,num-tx-queues=<3>; + fsl,num-rx-queues=<3>; + status = "disabled"; + }; + + fec2: ethernet@30bf0000 { + compatible = "fsl,imx7d-fec", "fsl,imx6sx-fec"; + reg = <0x30bf0000 0x10000>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>, + <&clks IMX7D_ENET_AXI_ROOT_CLK>, + <&clks IMX7D_ENET2_TIME_ROOT_CLK>, + <&clks IMX7D_PLL_ENET_MAIN_125M_CLK>, + <&clks IMX7D_ENET_PHY_REF_ROOT_CLK>; + clock-names = "ipg", "ahb", "ptp", + "enet_clk_ref", "enet_out"; + fsl,num-tx-queues=<3>; + fsl,num-rx-queues=<3>; + status = "disabled"; + }; }; }; }; diff --git a/arch/arm/boot/dts/k2e-evm.dts b/arch/arm/boot/dts/k2e-evm.dts index 50c83c21d911..b7e99807f5c2 100644 --- a/arch/arm/boot/dts/k2e-evm.dts +++ b/arch/arm/boot/dts/k2e-evm.dts @@ -13,7 +13,7 @@ #include "k2e.dtsi" / { - compatible = "ti,k2e-evm","ti,keystone"; + compatible = "ti,k2e-evm", "ti,k2e", "ti,keystone"; model = "Texas Instruments Keystone 2 Edison EVM"; soc { diff --git a/arch/arm/boot/dts/k2e-netcp.dtsi b/arch/arm/boot/dts/k2e-netcp.dtsi index b13b3c94e7fc..ac990f679725 100644 --- a/arch/arm/boot/dts/k2e-netcp.dtsi +++ b/arch/arm/boot/dts/k2e-netcp.dtsi @@ -72,7 +72,17 @@ qmss: qmss@2a40000 { qalloc-by-id; }; }; + accumulator { + acc-low-0 { + qrange = <480 32>; + accumulator = <0 47 16 2 50>; + interrupts = <0 226 0xf01>; + multi-queue; + qalloc-by-id; + }; + }; }; + descriptor-regions { #address-cells = <1>; #size-cells = <1>; @@ -83,6 +93,19 @@ qmss: qmss@2a40000 { link-index = <0x4000>; }; }; + + pdsps { + #address-cells = <1>; + #size-cells = <1>; + ranges; + pdsp0@0x2a10000 { + reg = <0x2a10000 0x1000 /*iram */ + 0x2a0f000 0x100 /*reg*/ + 0x2a0c000 0x3c8 /*intd */ + 0x2a20000 0x4000>; /*cmd*/ + id = <0>; + }; + }; }; /* qmss */ knav_dmas: knav_dmas@0 { diff --git a/arch/arm/boot/dts/k2e.dtsi b/arch/arm/boot/dts/k2e.dtsi index 675fb8e492c6..1097dada56d2 100644 --- a/arch/arm/boot/dts/k2e.dtsi +++ b/arch/arm/boot/dts/k2e.dtsi @@ -9,6 +9,9 @@ */ / { + compatible = "ti,k2e", "ti,keystone"; + model = "Texas Instruments Keystone 2 Edison SoC"; + cpus { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/k2hk-evm.dts b/arch/arm/boot/dts/k2hk-evm.dts index 660ebf58d547..8161bf53271b 100644 --- a/arch/arm/boot/dts/k2hk-evm.dts +++ b/arch/arm/boot/dts/k2hk-evm.dts @@ -13,7 +13,7 @@ #include "k2hk.dtsi" / { - compatible = "ti,k2hk-evm","ti,keystone"; + compatible = "ti,k2hk-evm", "ti,k2hk", "ti,keystone"; model = "Texas Instruments Keystone 2 Kepler/Hawking EVM"; soc { diff --git a/arch/arm/boot/dts/k2hk-netcp.dtsi b/arch/arm/boot/dts/k2hk-netcp.dtsi index 77a32c3c17e4..f86d6ddb832b 100644 --- a/arch/arm/boot/dts/k2hk-netcp.dtsi +++ b/arch/arm/boot/dts/k2hk-netcp.dtsi @@ -47,6 +47,7 @@ qmss: qmss@2a40000 { "region", "push", "pop"; }; }; + queue-pools { qpend { qpend-0 { @@ -88,7 +89,17 @@ qmss: qmss@2a40000 { qalloc-by-id; }; }; + accumulator { + acc-low-0 { + qrange = <480 32>; + accumulator = <0 47 16 2 50>; + interrupts = <0 226 0xf01>; + multi-queue; + qalloc-by-id; + }; + }; }; + descriptor-regions { #address-cells = <1>; #size-cells = <1>; @@ -99,6 +110,19 @@ qmss: qmss@2a40000 { link-index = <0x4000>; }; }; + + pdsps { + #address-cells = <1>; + #size-cells = <1>; + ranges; + pdsp0@0x2a10000 { + reg = <0x2a10000 0x1000 /*iram */ + 0x2a0f000 0x100 /*reg*/ + 0x2a0c000 0x3c8 /*intd */ + 0x2a20000 0x4000>; /*cmd*/ + id = <0>; + }; + }; }; /* qmss */ knav_dmas: knav_dmas@0 { diff --git a/arch/arm/boot/dts/k2hk.dtsi b/arch/arm/boot/dts/k2hk.dtsi index d0810a5f2968..ada4c7ac96e7 100644 --- a/arch/arm/boot/dts/k2hk.dtsi +++ b/arch/arm/boot/dts/k2hk.dtsi @@ -9,6 +9,9 @@ */ / { + compatible = "ti,k2hk", "ti,keystone"; + model = "Texas Instruments Keystone 2 Kepler/Hawking SoC"; + cpus { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/k2l-evm.dts b/arch/arm/boot/dts/k2l-evm.dts index 9a69a6b55374..00861244d788 100644 --- a/arch/arm/boot/dts/k2l-evm.dts +++ b/arch/arm/boot/dts/k2l-evm.dts @@ -13,7 +13,7 @@ #include "k2l.dtsi" / { - compatible = "ti,k2l-evm","ti,keystone"; + compatible = "ti,k2l-evm", "ti,k2l", "ti,keystone"; model = "Texas Instruments Keystone 2 Lamarr EVM"; soc { diff --git a/arch/arm/boot/dts/k2l-netcp.dtsi b/arch/arm/boot/dts/k2l-netcp.dtsi index 6b95284d11d4..01aef230773d 100644 --- a/arch/arm/boot/dts/k2l-netcp.dtsi +++ b/arch/arm/boot/dts/k2l-netcp.dtsi @@ -72,7 +72,16 @@ qmss: qmss@2a40000 { qalloc-by-id; }; }; + accumulator { + acc-low-0 { + qrange = <480 32>; + accumulator = <0 47 16 2 50>; + interrupts = <0 226 0xf01>; + multi-queue; + }; + }; }; + descriptor-regions { #address-cells = <1>; #size-cells = <1>; @@ -83,6 +92,20 @@ qmss: qmss@2a40000 { link-index = <0x4000>; }; }; + + pdsps { + #address-cells = <1>; + #size-cells = <1>; + ranges; + pdsp0@0x2a10000 { + reg = <0x2a10000 0x1000 /*iram */ + 0x2a0f000 0x100 /*reg*/ + 0x2a0c000 0x3c8 /*intd */ + 0x2a20000 0x4000>; /*cmd*/ + id = <0>; + }; + }; + }; /* qmss */ knav_dmas: knav_dmas@0 { diff --git a/arch/arm/boot/dts/k2l.dtsi b/arch/arm/boot/dts/k2l.dtsi index 49fd414f680c..4446da72b0ae 100644 --- a/arch/arm/boot/dts/k2l.dtsi +++ b/arch/arm/boot/dts/k2l.dtsi @@ -9,6 +9,9 @@ */ / { + compatible = "ti,k2l", "ti,keystone"; + model = "Texas Instruments Keystone 2 Lamarr SoC"; + cpus { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/keystone.dtsi b/arch/arm/boot/dts/keystone.dtsi index 72816d65f7ec..3f272826f537 100644 --- a/arch/arm/boot/dts/keystone.dtsi +++ b/arch/arm/boot/dts/keystone.dtsi @@ -12,6 +12,7 @@ #include "skeleton.dtsi" / { + compatible = "ti,keystone"; model = "Texas Instruments Keystone 2 SoC"; #address-cells = <2>; #size-cells = <2>; @@ -136,7 +137,7 @@ }; spi0: spi@21000400 { - compatible = "ti,dm6441-spi"; + compatible = "ti,keystone-spi", "ti,dm6441-spi"; reg = <0x21000400 0x200>; num-cs = <4>; ti,davinci-spi-intr-line = <0>; @@ -147,7 +148,7 @@ }; spi1: spi@21000600 { - compatible = "ti,dm6441-spi"; + compatible = "ti,keystone-spi", "ti,dm6441-spi"; reg = <0x21000600 0x200>; num-cs = <4>; ti,davinci-spi-intr-line = <0>; @@ -158,7 +159,7 @@ }; spi2: spi@21000800 { - compatible = "ti,dm6441-spi"; + compatible = "ti,keystone-spi", "ti,dm6441-spi"; reg = <0x21000800 0x200>; num-cs = <4>; ti,davinci-spi-intr-line = <0>; diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi index 464f09a1a4a5..7b5a4a18f49c 100644 --- a/arch/arm/boot/dts/kirkwood.dtsi +++ b/arch/arm/boot/dts/kirkwood.dtsi @@ -40,16 +40,6 @@ pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256 MiB memory space */ pcie-io-aperture = <0xf2000000 0x100000>; /* 1 MiB I/O space */ - cesa: crypto@0301 { - compatible = "marvell,orion-crypto"; - reg = <MBUS_ID(0xf0, 0x01) 0x30000 0x10000>, - <MBUS_ID(0x03, 0x01) 0 0x800>; - reg-names = "regs", "sram"; - interrupts = <22>; - clocks = <&gate_clk 17>; - status = "okay"; - }; - nand: nand@012f { #address-cells = <1>; #size-cells = <1>; @@ -65,6 +55,14 @@ pinctrl-names = "default"; status = "disabled"; }; + + crypto_sram: sa-sram@0301 { + compatible = "mmio-sram"; + reg = <MBUS_ID(0x03, 0x01) 0x0 0x800>; + clocks = <&gate_clk 17>; + #address-cells = <1>; + #size-cells = <1>; + }; }; ocp@f1000000 { @@ -252,6 +250,17 @@ status = "okay"; }; + cesa: crypto@30000 { + compatible = "marvell,kirkwood-crypto"; + reg = <0x30000 0x10000>; + reg-names = "regs"; + interrupts = <22>; + clocks = <&gate_clk 17>; + marvell,crypto-srams = <&crypto_sram>; + marvell,crypto-sram-size = <0x800>; + status = "okay"; + }; + usb0: ehci@50000 { compatible = "marvell,orion-ehci"; reg = <0x50000 0x1000>; diff --git a/arch/arm/boot/dts/lpc18xx.dtsi b/arch/arm/boot/dts/lpc18xx.dtsi index 2c569a6ddc9a..52591d83e8cd 100644 --- a/arch/arm/boot/dts/lpc18xx.dtsi +++ b/arch/arm/boot/dts/lpc18xx.dtsi @@ -68,6 +68,46 @@ }; soc { + sct_pwm: pwm@40000000 { + compatible = "nxp,lpc1850-sct-pwm"; + reg = <0x40000000 0x1000>; + clocks =<&ccu1 CLK_CPU_SCT>; + clock-names = "pwm"; + resets = <&rgu 37>; + #pwm-cells = <3>; + status = "disabled"; + }; + + dmac: dma-controller@40002000 { + compatible = "arm,pl080", "arm,primecell"; + arm,primecell-periphid = <0x00041080>; + reg = <0x40002000 0x1000>; + interrupts = <2>; + clocks = <&ccu1 CLK_CPU_DMA>; + clock-names = "apb_pclk"; + resets = <&rgu 19>; + #dma-cells = <2>; + dma-channels = <8>; + dma-requests = <16>; + lli-bus-interface-ahb1; + lli-bus-interface-ahb2; + mem-bus-interface-ahb1; + mem-bus-interface-ahb2; + memcpy-burst-size = <256>; + memcpy-bus-width = <32>; + }; + + spifi: flash-controller@40003000 { + compatible = "nxp,lpc1773-spifi"; + reg = <0x40003000 0x1000>, <0x14000000 0x4000000>; + reg-names = "spifi", "flash"; + interrupts = <30>; + clocks = <&ccu1 CLK_SPIFI>, <&ccu1 CLK_CPU_SPIFI>; + clock-names = "spifi", "reg"; + resets = <&rgu 53>; + status = "disabled"; + }; + mmcsd: mmcsd@40004000 { compatible = "snps,dw-mshc"; reg = <0x40004000 0x1000>; @@ -75,6 +115,7 @@ num-slots = <1>; clocks = <&ccu2 CLK_SDIO>, <&ccu1 CLK_CPU_SDIO>; clock-names = "ciu", "biu"; + resets = <&rgu 20>; status = "disabled"; }; @@ -83,6 +124,7 @@ reg = <0x40006100 0x100>; interrupts = <8>; clocks = <&ccu1 CLK_CPU_USB0>; + resets = <&rgu 17>; phys = <&usb0_otg_phy>; phy-names = "usb"; has-transaction-translator; @@ -94,6 +136,7 @@ reg = <0x40007100 0x100>; interrupts = <9>; clocks = <&ccu1 CLK_CPU_USB1>; + resets = <&rgu 18>; status = "disabled"; }; @@ -102,6 +145,7 @@ reg = <0x40005000 0x1000>; clocks = <&ccu1 CLK_CPU_EMCDIV>, <&ccu1 CLK_CPU_EMC>; clock-names = "mpmcclk", "apb_pclk"; + resets = <&rgu 21>; #address-cells = <2>; #size-cells = <1>; ranges = <0 0 0x1c000000 0x1000000 @@ -118,6 +162,7 @@ interrupt-names = "combined"; clocks = <&cgu BASE_LCD_CLK>, <&ccu1 CLK_CPU_LCD>; clock-names = "clcdclk", "apb_pclk"; + resets = <&rgu 16>; status = "disabled"; }; @@ -128,6 +173,8 @@ interrupt-names = "macirq"; clocks = <&ccu1 CLK_CPU_ETHERNET>; clock-names = "stmmaceth"; + resets = <&rgu 22>; + reset-names = "stmmaceth"; status = "disabled"; }; @@ -135,12 +182,20 @@ compatible = "nxp,lpc1850-creg", "syscon", "simple-mfd"; reg = <0x40043000 0x1000>; clocks = <&ccu1 CLK_CPU_CREG>; + resets = <&rgu 5>; usb0_otg_phy: phy@004 { compatible = "nxp,lpc1850-usb-otg-phy"; clocks = <&ccu1 CLK_USB0>; #phy-cells = <0>; }; + + dmamux: dma-mux@11c { + compatible = "nxp,lpc1850-dmamux"; + #dma-cells = <3>; + dma-requests = <64>; + dma-masters = <&dmac>; + }; }; cgu: clock-controller@40050000 { @@ -178,6 +233,22 @@ "base_ssp0_clk", "base_sdio_clk"; }; + rgu: reset-controller@40053000 { + compatible = "nxp,lpc1850-rgu"; + reg = <0x40053000 0x1000>; + clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_BUS>; + clock-names = "delay", "reg"; + #reset-cells = <1>; + }; + + watchdog@40080000 { + compatible = "nxp,lpc1850-wwdt"; + reg = <0x40080000 0x24>; + interrupts = <49>; + clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_WWDT>; + clock-names = "wdtclk", "reg"; + }; + uart0: serial@40081000 { compatible = "nxp,lpc1850-uart", "ns16550a"; reg = <0x40081000 0x1000>; @@ -185,6 +256,12 @@ interrupts = <24>; clocks = <&ccu2 CLK_APB0_UART0>, <&ccu1 CLK_CPU_UART0>; clock-names = "uartclk", "reg"; + resets = <&rgu 44>; + dmas = <&dmamux 1 1 2 + &dmamux 2 1 2 + &dmamux 11 2 2 + &dmamux 12 2 2>; + dma-names = "tx", "rx", "tx", "rx"; status = "disabled"; }; @@ -195,6 +272,10 @@ interrupts = <25>; clocks = <&ccu2 CLK_APB0_UART1>, <&ccu1 CLK_CPU_UART1>; clock-names = "uartclk", "reg"; + resets = <&rgu 45>; + dmas = <&dmamux 3 1 2 + &dmamux 4 1 2>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -204,6 +285,10 @@ interrupts = <22>; clocks = <&ccu2 CLK_APB0_SSP0>, <&ccu1 CLK_CPU_SSP0>; clock-names = "sspclk", "apb_pclk"; + resets = <&rgu 50>; + dmas = <&dmamux 9 0 2 + &dmamux 10 0 2>; + dma-names = "rx", "tx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -215,6 +300,7 @@ interrupts = <12>; clocks = <&ccu1 CLK_CPU_TIMER0>; clock-names = "timerclk"; + resets = <&rgu 32>; }; timer1: timer@40085000 { @@ -223,6 +309,7 @@ interrupts = <13>; clocks = <&ccu1 CLK_CPU_TIMER1>; clock-names = "timerclk"; + resets = <&rgu 33>; }; pinctrl: pinctrl@40086000 { @@ -231,11 +318,23 @@ clocks = <&ccu1 CLK_CPU_SCU>; }; + i2c0: i2c@400a1000 { + compatible = "nxp,lpc1788-i2c"; + reg = <0x400a1000 0x1000>; + interrupts = <18>; + clocks = <&ccu1 CLK_APB1_I2C0>; + resets = <&rgu 48>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + can1: can@400a4000 { compatible = "bosch,c_can"; reg = <0x400a4000 0x1000>; interrupts = <43>; clocks = <&ccu1 CLK_APB1_CAN1>; + resets = <&rgu 54>; status = "disabled"; }; @@ -246,6 +345,10 @@ interrupts = <26>; clocks = <&ccu2 CLK_APB2_UART2>, <&ccu1 CLK_CPU_UART2>; clock-names = "uartclk", "reg"; + resets = <&rgu 46>; + dmas = <&dmamux 5 1 2 + &dmamux 6 1 2>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -256,6 +359,12 @@ interrupts = <27>; clocks = <&ccu2 CLK_APB2_UART3>, <&ccu1 CLK_CPU_UART3>; clock-names = "uartclk", "reg"; + resets = <&rgu 47>; + dmas = <&dmamux 7 1 2 + &dmamux 8 1 2 + &dmamux 13 3 2 + &dmamux 14 3 2>; + dma-names = "tx", "rx", "rx", "tx"; status = "disabled"; }; @@ -265,6 +374,7 @@ interrupts = <14>; clocks = <&ccu1 CLK_CPU_TIMER2>; clock-names = "timerclk"; + resets = <&rgu 34>; }; timer3: timer@400c4000 { @@ -273,6 +383,7 @@ interrupts = <15>; clocks = <&ccu1 CLK_CPU_TIMER3>; clock-names = "timerclk"; + resets = <&rgu 35>; }; ssp1: spi@400c5000 { @@ -281,6 +392,28 @@ interrupts = <23>; clocks = <&ccu2 CLK_APB2_SSP1>, <&ccu1 CLK_CPU_SSP1>; clock-names = "sspclk", "apb_pclk"; + resets = <&rgu 51>; + dmas = <&dmamux 11 2 2 + &dmamux 12 2 2 + &dmamux 3 3 2 + &dmamux 4 3 2 + &dmamux 5 2 2 + &dmamux 6 2 2 + &dmamux 13 2 2 + &dmamux 14 2 2>; + dma-names = "rx", "tx", "tx", "rx", + "tx", "rx", "rx", "tx"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c1: i2c@400e0000 { + compatible = "nxp,lpc1788-i2c"; + reg = <0x400e0000 0x1000>; + interrupts = <19>; + clocks = <&ccu1 CLK_APB3_I2C1>; + resets = <&rgu 49>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -291,6 +424,7 @@ reg = <0x400e2000 0x1000>; interrupts = <51>; clocks = <&ccu1 CLK_APB3_CAN0>; + resets = <&rgu 55>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/lpc4350-hitex-eval.dts b/arch/arm/boot/dts/lpc4350-hitex-eval.dts index 32bc7ff4eb2a..022d495432c1 100644 --- a/arch/arm/boot/dts/lpc4350-hitex-eval.dts +++ b/arch/arm/boot/dts/lpc4350-hitex-eval.dts @@ -15,6 +15,9 @@ #include "lpc18xx.dtsi" #include "lpc4350.dtsi" +#include "dt-bindings/input/input.h" +#include "dt-bindings/gpio/gpio.h" + / { model = "Hitex LPC4350 Evaluation Board"; compatible = "hitex,lpc4350-eval-board", "nxp,lpc4350"; @@ -34,6 +37,88 @@ device_type = "memory"; reg = <0x28000000 0x800000>; /* 8 MB */ }; + + pca_buttons { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + autorepeat; + + button@0 { + label = "joy:right"; + linux,code = <KEY_RIGHT>; + gpios = <&pca_gpio 8 GPIO_ACTIVE_LOW>; + }; + + button@1 { + label = "joy:up"; + linux,code = <KEY_UP>; + gpios = <&pca_gpio 9 GPIO_ACTIVE_LOW>; + }; + + + button@2 { + label = "joy:enter"; + linux,code = <KEY_ENTER>; + gpios = <&pca_gpio 10 GPIO_ACTIVE_LOW>; + }; + + button@3 { + label = "joy:left"; + linux,code = <KEY_LEFT>; + gpios = <&pca_gpio 11 GPIO_ACTIVE_LOW>; + }; + + button@4 { + label = "joy:down"; + linux,code = <KEY_DOWN>; + gpios = <&pca_gpio 12 GPIO_ACTIVE_LOW>; + }; + + button@5 { + label = "user:sw3"; + linux,code = <KEY_F1>; + gpios = <&pca_gpio 13 GPIO_ACTIVE_LOW>; + }; + + button@6 { + label = "user:sw4"; + linux,code = <KEY_F2>; + gpios = <&pca_gpio 14 GPIO_ACTIVE_LOW>; + }; + + button@7 { + label = "user:sw5"; + linux,code = <KEY_F3>; + gpios = <&pca_gpio 15 GPIO_ACTIVE_LOW>; + }; + }; + + pca_leds { + compatible = "gpio-leds"; + + led0 { + label = "ext:led0"; + gpios = <&pca_gpio 0 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + + led1 { + label = "ext:led1"; + gpios = <&pca_gpio 1 GPIO_ACTIVE_LOW>; + }; + + led2 { + label = "ext:led2"; + gpios = <&pca_gpio 2 GPIO_ACTIVE_LOW>; + }; + + led3 { + label = "ext:led3"; + gpios = <&pca_gpio 3 GPIO_ACTIVE_LOW>; + }; + }; }; &pinctrl { @@ -186,6 +271,43 @@ }; }; + i2c0_pins: i2c0-pins { + i2c0_pins_cfg { + pins = "i2c0_scl", "i2c0_sda"; + function = "i2c0"; + input-enable; + }; + }; + + spifi_pins: spifi-pins { + spifi_clk_cfg { + pins = "p3_3"; + function = "spifi"; + slew-rate = <1>; + bias-disable; + input-enable; + input-schmitt-disable; + }; + + spifi_mosi_miso_sio2_3_cfg { + pins = "p3_7", "p3_6", "p3_5", "p3_4"; + function = "spifi"; + slew-rate = <1>; + bias-disable; + input-enable; + input-schmitt-disable; + }; + + spifi_cs_cfg { + pins = "p3_8"; + function = "spifi"; + slew-rate = <1>; + bias-disable; + input-enable; + input-schmitt-disable; + }; + }; + uart0_pins: uart0-pins { uart0_rx_cfg { pins = "pf_11"; @@ -271,6 +393,31 @@ clock-frequency = <25000000>; }; +&i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + clock-frequency = <400000>; + + /* NXP SE97BTP with temperature sensor + eeprom */ + sensor@18 { + compatible = "nxp,jc42"; + reg = <0x18>; + }; + + eeprom@50 { + compatible = "nxp,24c02"; + reg = <0x50>; + }; + + pca_gpio: gpio@24 { + compatible = "nxp,pca9673"; + reg = <0x24>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + &mac { status = "okay"; phy-mode = "mii"; @@ -278,6 +425,34 @@ pinctrl-0 = <&enet_mii_pins>; }; +&spifi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&spifi_pins>; + + flash@0 { + compatible = "jedec,spi-nor"; + spi-rx-bus-width = <4>; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "bootloader"; + reg = <0x000000 0x040000>; /* 256 KiB */ + }; + + partition@1 { + label = "kernel"; + reg = <0x040000 0x2c0000>; /* 2.75 MiB */ + }; + + partition@2 { + label = "rootfs"; + reg = <0x300000 0x500000>; /* 5 MiB */ + }; + }; +}; + &uart0 { status = "okay"; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/lpc4357-ea4357-devkit.dts b/arch/arm/boot/dts/lpc4357-ea4357-devkit.dts index 5f7bdad80963..391121d24daa 100644 --- a/arch/arm/boot/dts/lpc4357-ea4357-devkit.dts +++ b/arch/arm/boot/dts/lpc4357-ea4357-devkit.dts @@ -332,6 +332,14 @@ }; }; + i2c0_pins: i2c0-pins { + i2c0_pins_cfg { + pins = "i2c0_scl", "i2c0_sda"; + function = "i2c0"; + input-enable; + }; + }; + sdmmc_pins: sdmmc-pins { sdmmc_clk_cfg { pins = "pc_0"; @@ -363,6 +371,49 @@ }; }; + spifi_pins: spifi-pins { + spifi_clk_cfg { + pins = "p3_3"; + function = "spifi"; + slew-rate = <1>; + bias-disable; + input-enable; + input-schmitt-disable; + }; + + spifi_mosi_miso_sio2_3_cfg { + pins = "p3_7", "p3_6", "p3_5", "p3_4"; + function = "spifi"; + slew-rate = <0>; + bias-disable; + input-enable; + input-schmitt-disable; + }; + + spifi_cs_cfg { + pins = "p3_8"; + function = "spifi"; + bias-disable; + }; + }; + + ssp0_pins: ssp0-pins { + ssp0_sck_miso_mosi { + pins = "pf_0", "pf_2", "pf_3"; + function = "ssp0"; + slew-rate = <1>; + bias-pull-down; + input-enable; + input-schmitt-disable; + }; + + ssp0_ssel { + pins = "pf_1"; + function = "ssp0"; + bias-pull-up; + }; + }; + uart0_pins: uart0-pins { uart0_rx_cfg { pins = "pf_11"; @@ -410,6 +461,23 @@ }; }; +&i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + clock-frequency = <400000>; + + lm75@48 { + compatible = "nxp,lm75"; + reg = <0x48>; + }; + + eeprom@57 { + compatible = "microchip,24c64"; + reg = <0x57>; + }; +}; + &emc { status = "okay"; pinctrl-names = "default"; @@ -489,6 +557,33 @@ pinctrl-0 = <&sdmmc_pins>; }; +&spifi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&spifi_pins>; + + flash@0 { + compatible = "jedec,spi-nor"; + spi-cpol; + spi-cpha; + spi-rx-bus-width = <4>; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "data"; + reg = <0 0x200000>; + }; + }; +}; + +&ssp0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&ssp0_pins>; + num-cs = <1>; +}; + &uart0 { status = "okay"; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/ls1021a-twr.dts b/arch/arm/boot/dts/ls1021a-twr.dts index e008f9367510..fbb89d13401e 100644 --- a/arch/arm/boot/dts/ls1021a-twr.dts +++ b/arch/arm/boot/dts/ls1021a-twr.dts @@ -144,6 +144,19 @@ &i2c0 { status = "okay"; + + ina220@40 { + compatible = "ti,ina220"; + reg = <0x40>; + shunt-resistor = <1000>; + }; + + ina220@41 { + compatible = "ti,ina220"; + reg = <0x41>; + shunt-resistor = <1000>; + }; + }; &i2c1 { diff --git a/arch/arm/boot/dts/ls1021a.dtsi b/arch/arm/boot/dts/ls1021a.dtsi index 973a496207fc..9430a9928199 100644 --- a/arch/arm/boot/dts/ls1021a.dtsi +++ b/arch/arm/boot/dts/ls1021a.dtsi @@ -53,6 +53,7 @@ interrupt-parent = <&gic>; aliases { + crypto = &crypto; ethernet0 = &enet0; ethernet1 = &enet1; ethernet2 = &enet2; @@ -148,6 +149,45 @@ big-endian; }; + crypto: crypto@1700000 { + compatible = "fsl,sec-v5.0", "fsl,sec-v4.0"; + fsl,sec-era = <7>; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0 0x1700000 0x0 0x100000>; + ranges = <0x0 0x0 0x1700000 0x100000>; + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; + + sec_jr0: jr@10000 { + compatible = "fsl,sec-v5.0-job-ring", + "fsl,sec-v4.0-job-ring"; + reg = <0x10000 0x10000>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + }; + + sec_jr1: jr@20000 { + compatible = "fsl,sec-v5.0-job-ring", + "fsl,sec-v4.0-job-ring"; + reg = <0x20000 0x10000>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; + }; + + sec_jr2: jr@30000 { + compatible = "fsl,sec-v5.0-job-ring", + "fsl,sec-v4.0-job-ring"; + reg = <0x30000 0x10000>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + }; + + sec_jr3: jr@40000 { + compatible = "fsl,sec-v5.0-job-ring", + "fsl,sec-v4.0-job-ring"; + reg = <0x40000 0x10000>; + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; + }; + + }; + clockgen: clocking@1ee1000 { #address-cells = <1>; #size-cells = <1>; @@ -405,6 +445,7 @@ model = "eTSEC"; fsl,magic-packet; ranges; + dma-coherent; queue-group@2d10000 { #address-cells = <2>; @@ -433,6 +474,7 @@ interrupt-parent = <&gic>; model = "eTSEC"; ranges; + dma-coherent; queue-group@2d50000 { #address-cells = <2>; @@ -461,6 +503,7 @@ interrupt-parent = <&gic>; model = "eTSEC"; ranges; + dma-coherent; queue-group@2d90000 { #address-cells = <2>; @@ -494,6 +537,7 @@ reg = <0x0 0x3100000 0x0 0x10000>; interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; dr_mode = "host"; + snps,quirk-frame-length-adjustment = <0x20>; }; }; }; diff --git a/arch/arm/boot/dts/meson8b-mxq.dts b/arch/arm/boot/dts/meson8b-mxq.dts new file mode 100644 index 000000000000..c7fdaeabbe7b --- /dev/null +++ b/arch/arm/boot/dts/meson8b-mxq.dts @@ -0,0 +1,67 @@ +/* + * Copyright 2015 Endless Mobile, Inc. + * Author: Carlo Caione <carlo@endlessm.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "meson8b.dtsi" + +/ { + model = "TRONFY MXQ S805"; + compatible = "tronfy,mxq", "amlogic,meson8b"; + + aliases { + serial0 = &uart_AO; + }; + + memory { + reg = <0x40000000 0x40000000>; + }; +}; + +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts new file mode 100644 index 000000000000..a8e2911b2cbe --- /dev/null +++ b/arch/arm/boot/dts/meson8b-odroidc1.dts @@ -0,0 +1,67 @@ +/* + * Copyright 2015 Endless Mobile, Inc. + * Author: Carlo Caione <carlo@endlessm.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "meson8b.dtsi" + +/ { + model = "Hardkernel ODROID-C1"; + compatible = "hardkernel,odroid-c1", "amlogic,meson8b"; + + aliases { + serial0 = &uart_AO; + }; + + memory { + reg = <0x40000000 0x40000000>; + }; +}; + +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; diff --git a/arch/arm/boot/dts/meson8b.dtsi b/arch/arm/boot/dts/meson8b.dtsi new file mode 100644 index 000000000000..ee352bf687ff --- /dev/null +++ b/arch/arm/boot/dts/meson8b.dtsi @@ -0,0 +1,186 @@ +/* + * Copyright 2015 Endless Mobile, Inc. + * Author: Carlo Caione <carlo@endlessm.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/clock/meson8b-clkc.h> +#include <dt-bindings/gpio/meson8b-gpio.h> +#include "skeleton.dtsi" + +/ { + interrupt-parent = <&gic>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@200 { + device_type = "cpu"; + compatible = "arm,cortex-a5"; + next-level-cache = <&L2>; + reg = <0x200>; + }; + + cpu@201 { + device_type = "cpu"; + compatible = "arm,cortex-a5"; + next-level-cache = <&L2>; + reg = <0x201>; + }; + + cpu@202 { + device_type = "cpu"; + compatible = "arm,cortex-a5"; + next-level-cache = <&L2>; + reg = <0x202>; + }; + + cpu@203 { + device_type = "cpu"; + compatible = "arm,cortex-a5"; + next-level-cache = <&L2>; + reg = <0x203>; + }; + }; + + soc { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + L2: l2-cache-controller@c4200000 { + compatible = "arm,pl310-cache"; + reg = <0xc4200000 0x1000>; + cache-unified; + cache-level = <2>; + }; + + gic: interrupt-controller@c4301000 { + compatible = "arm,cortex-a9-gic"; + reg = <0xc4301000 0x1000>, + <0xc4300100 0x0100>; + interrupt-controller; + #interrupt-cells = <3>; + }; + + timer@c1109940 { + compatible = "amlogic,meson6-timer"; + reg = <0xc1109940 0x18>; + interrupts = <0 10 1>; + }; + + uart_AO: serial@c81004c0 { + compatible = "amlogic,meson-uart"; + reg = <0xc81004c0 0x18>; + interrupts = <0 90 1>; + clocks = <&clkc CLKID_CLK81>; + status = "disabled"; + }; + + uart_A: serial@c11084c0 { + compatible = "amlogic,meson-uart"; + reg = <0xc11084c0 0x18>; + interrupts = <0 26 1>; + clocks = <&clkc CLKID_CLK81>; + status = "disabled"; + }; + + uart_B: serial@c11084dc { + compatible = "amlogic,meson-uart"; + reg = <0xc11084dc 0x18>; + interrupts = <0 75 1>; + clocks = <&clkc CLKID_CLK81>; + status = "disabled"; + }; + + uart_C: serial@c1108700 { + compatible = "amlogic,meson-uart"; + reg = <0xc1108700 0x18>; + interrupts = <0 93 1>; + clocks = <&clkc CLKID_CLK81>; + status = "disabled"; + }; + + clkc: clock-controller@c1104000 { + #clock-cells = <1>; + compatible = "amlogic,meson8b-clkc"; + reg = <0xc1108000 0x4>, <0xc1104000 0x460>; + }; + + pinctrl: pinctrl@c1109880 { + compatible = "amlogic,meson8b-pinctrl"; + reg = <0xc1109880 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gpio: banks@c11080b0 { + reg = <0xc11080b0 0x28>, + <0xc11080e8 0x18>, + <0xc1108120 0x18>, + <0xc1108030 0x38>; + reg-names = "mux", "pull", "pull-enable", "gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio_ao: ao-bank@c1108030 { + reg = <0xc8100014 0x4>, + <0xc810002c 0x4>, + <0xc8100024 0x8>; + reg-names = "mux", "pull", "gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + uart_ao_a_pins: uart_ao_a { + mux { + groups = "uart_tx_ao_a", "uart_rx_ao_a"; + function = "uart_ao"; + }; + }; + }; + }; +}; /* end of / */ diff --git a/arch/arm/boot/dts/mt8127.dtsi b/arch/arm/boot/dts/mt8127.dtsi index ca3402e8240b..52086c8018e2 100644 --- a/arch/arm/boot/dts/mt8127.dtsi +++ b/arch/arm/boot/dts/mt8127.dtsi @@ -23,6 +23,7 @@ cpus { #address-cells = <1>; #size-cells = <0>; + enable-method = "mediatek,mt81xx-tz-smp"; cpu@0 { device_type = "cpu"; @@ -47,6 +48,17 @@ }; + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + trustzone-bootinfo@80002000 { + compatible = "mediatek,trustzone-bootinfo"; + reg = <0 0x80002000 0 0x1000>; + }; + }; + clocks { #address-cells = <2>; #size-cells = <2>; @@ -72,6 +84,21 @@ }; }; + timer { + compatible = "arm,armv7-timer"; + interrupt-parent = <&gic>; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_LOW)>; + clock-frequency = <13000000>; + arm,cpu-registers-not-fw-configured; + }; + soc { #address-cells = <2>; #size-cells = <2>; diff --git a/arch/arm/boot/dts/mt8135-evbp1.dts b/arch/arm/boot/dts/mt8135-evbp1.dts index 357a91fc2d1d..460db6d05952 100644 --- a/arch/arm/boot/dts/mt8135-evbp1.dts +++ b/arch/arm/boot/dts/mt8135-evbp1.dts @@ -32,7 +32,6 @@ compatible = "mediatek,mt6397-regulator"; mt6397_vpca15_reg: buck_vpca15 { - regulator-compatible = "buck_vpca15"; regulator-name = "vpca15"; regulator-min-microvolt = < 850000>; regulator-max-microvolt = <1350000>; @@ -41,7 +40,6 @@ }; mt6397_vpca7_reg: buck_vpca7 { - regulator-compatible = "buck_vpca7"; regulator-name = "vpca7"; regulator-min-microvolt = < 850000>; regulator-max-microvolt = <1350000>; @@ -50,7 +48,6 @@ }; mt6397_vsramca15_reg: buck_vsramca15 { - regulator-compatible = "buck_vsramca15"; regulator-name = "vsramca15"; regulator-min-microvolt = < 850000>; regulator-max-microvolt = <1350000>; @@ -59,7 +56,6 @@ }; mt6397_vsramca7_reg: buck_vsramca7 { - regulator-compatible = "buck_vsramca7"; regulator-name = "vsramca7"; regulator-min-microvolt = < 850000>; regulator-max-microvolt = <1350000>; @@ -68,7 +64,6 @@ }; mt6397_vcore_reg: buck_vcore { - regulator-compatible = "buck_vcore"; regulator-name = "vcore"; regulator-min-microvolt = < 850000>; regulator-max-microvolt = <1350000>; @@ -77,7 +72,6 @@ }; mt6397_vgpu_reg: buck_vgpu { - regulator-compatible = "buck_vgpu"; regulator-name = "vgpu"; regulator-min-microvolt = < 700000>; regulator-max-microvolt = <1350000>; @@ -86,7 +80,6 @@ }; mt6397_vdrm_reg: buck_vdrm { - regulator-compatible = "buck_vdrm"; regulator-name = "vdrm"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1400000>; @@ -95,7 +88,6 @@ }; mt6397_vio18_reg: buck_vio18 { - regulator-compatible = "buck_vio18"; regulator-name = "vio18"; regulator-min-microvolt = <1620000>; regulator-max-microvolt = <1980000>; @@ -104,19 +96,16 @@ }; mt6397_vtcxo_reg: ldo_vtcxo { - regulator-compatible = "ldo_vtcxo"; regulator-name = "vtcxo"; regulator-always-on; }; mt6397_va28_reg: ldo_va28 { - regulator-compatible = "ldo_va28"; regulator-name = "va28"; regulator-always-on; }; mt6397_vcama_reg: ldo_vcama { - regulator-compatible = "ldo_vcama"; regulator-name = "vcama"; regulator-min-microvolt = <1500000>; regulator-max-microvolt = <2800000>; @@ -124,18 +113,15 @@ }; mt6397_vio28_reg: ldo_vio28 { - regulator-compatible = "ldo_vio28"; regulator-name = "vio28"; regulator-always-on; }; mt6397_vusb_reg: ldo_vusb { - regulator-compatible = "ldo_vusb"; regulator-name = "vusb"; }; mt6397_vmc_reg: ldo_vmc { - regulator-compatible = "ldo_vmc"; regulator-name = "vmc"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; @@ -143,7 +129,6 @@ }; mt6397_vmch_reg: ldo_vmch { - regulator-compatible = "ldo_vmch"; regulator-name = "vmch"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3300000>; @@ -151,7 +136,6 @@ }; mt6397_vemc_3v3_reg: ldo_vemc3v3 { - regulator-compatible = "ldo_vemc3v3"; regulator-name = "vemc_3v3"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3300000>; @@ -159,7 +143,6 @@ }; mt6397_vgp1_reg: ldo_vgp1 { - regulator-compatible = "ldo_vgp1"; regulator-name = "vcamd"; regulator-min-microvolt = <1220000>; regulator-max-microvolt = <3300000>; @@ -167,7 +150,6 @@ }; mt6397_vgp2_reg: ldo_vgp2 { - regulator-compatible = "ldo_vgp2"; regulator-name = "vcamio"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; @@ -175,7 +157,6 @@ }; mt6397_vgp3_reg: ldo_vgp3 { - regulator-compatible = "ldo_vgp3"; regulator-name = "vcamaf"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <3300000>; @@ -183,7 +164,6 @@ }; mt6397_vgp4_reg: ldo_vgp4 { - regulator-compatible = "ldo_vgp4"; regulator-name = "vgp4"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <3300000>; @@ -191,7 +171,6 @@ }; mt6397_vgp5_reg: ldo_vgp5 { - regulator-compatible = "ldo_vgp5"; regulator-name = "vgp5"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <3000000>; @@ -199,7 +178,6 @@ }; mt6397_vgp6_reg: ldo_vgp6 { - regulator-compatible = "ldo_vgp6"; regulator-name = "vgp6"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <3300000>; @@ -207,7 +185,6 @@ }; mt6397_vibr_reg: ldo_vibr { - regulator-compatible = "ldo_vibr"; regulator-name = "vibr"; regulator-min-microvolt = <1300000>; regulator-max-microvolt = <3300000>; diff --git a/arch/arm/boot/dts/mt8135.dtsi b/arch/arm/boot/dts/mt8135.dtsi index 08371dbae543..cb99b02d2ccc 100644 --- a/arch/arm/boot/dts/mt8135.dtsi +++ b/arch/arm/boot/dts/mt8135.dtsi @@ -46,6 +46,7 @@ cpus { #address-cells = <1>; #size-cells = <0>; + enable-method = "mediatek,mt81xx-tz-smp"; cpu0: cpu@0 { device_type = "cpu"; @@ -72,6 +73,17 @@ }; }; + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + trustzone-bootinfo@80002000 { + compatible = "mediatek,trustzone-bootinfo"; + reg = <0 0x80002000 0 0x1000>; + }; + }; + clocks { #address-cells = <2>; #size-cells = <2>; @@ -97,6 +109,21 @@ }; }; + timer { + compatible = "arm,armv7-timer"; + interrupt-parent = <&gic>; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_LOW)>; + clock-frequency = <13000000>; + arm,cpu-registers-not-fw-configured; + }; + soc { #address-cells = <2>; #size-cells = <2>; diff --git a/arch/arm/boot/dts/nspire.dtsi b/arch/arm/boot/dts/nspire.dtsi index 390c91aea16d..ee5a0bb22354 100644 --- a/arch/arm/boot/dts/nspire.dtsi +++ b/arch/arm/boot/dts/nspire.dtsi @@ -16,7 +16,7 @@ cpus { cpu@0 { - compatible = "arm,arm926ejs"; + compatible = "arm,arm926ej-s"; }; }; diff --git a/arch/arm/boot/dts/omap2420-n8x0-common.dtsi b/arch/arm/boot/dts/omap2420-n8x0-common.dtsi index c9f1e93a95ae..8491f46c61b7 100644 --- a/arch/arm/boot/dts/omap2420-n8x0-common.dtsi +++ b/arch/arm/boot/dts/omap2420-n8x0-common.dtsi @@ -9,9 +9,9 @@ ocp { i2c@0 { compatible = "i2c-cbus-gpio"; - gpios = <&gpio3 2 0 /* gpio66 clk */ - &gpio3 1 0 /* gpio65 dat */ - &gpio3 0 0 /* gpio64 sel */ + gpios = <&gpio3 2 GPIO_ACTIVE_HIGH /* gpio66 clk */ + &gpio3 1 GPIO_ACTIVE_HIGH /* gpio65 dat */ + &gpio3 0 GPIO_ACTIVE_HIGH /* gpio64 sel */ >; #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index 7c4dca122a91..73f1e3a8f62c 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -80,7 +80,7 @@ regulator-name = "hsusb2_vbus"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - gpio = <&twl_gpio 18 0>; /* GPIO LEDA */ + gpio = <&twl_gpio 18 GPIO_ACTIVE_HIGH>; /* GPIO LEDA */ startup-delay-us = <70000>; }; diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index 67659a0ed13e..274c2c482aaa 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -55,7 +55,7 @@ regulator-name = "hsusb2_vbus"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - gpio = <&twl_gpio 18 0>; /* GPIO LEDA */ + gpio = <&twl_gpio 18 GPIO_ACTIVE_HIGH>; /* GPIO LEDA */ startup-delay-us = <70000>; }; diff --git a/arch/arm/boot/dts/omap3-cm-t3x.dtsi b/arch/arm/boot/dts/omap3-cm-t3x.dtsi index 4d091ca43e25..8c813e77b17f 100644 --- a/arch/arm/boot/dts/omap3-cm-t3x.dtsi +++ b/arch/arm/boot/dts/omap3-cm-t3x.dtsi @@ -224,7 +224,7 @@ interrupt-parent = <&gpio2>; interrupts = <25 0>; /* gpio_57 */ - pendown-gpio = <&gpio2 25 0>; + pendown-gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>; ti,x-min = /bits/ 16 <0x0>; ti,x-max = /bits/ 16 <0x0fff>; diff --git a/arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi b/arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi index e84184de2a4a..4813e96157b3 100644 --- a/arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi +++ b/arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi @@ -54,7 +54,7 @@ interrupt-parent = <&gpio1>; interrupts = <27 0>; /* gpio_27 */ - pendown-gpio = <&gpio1 27 0>; + pendown-gpio = <&gpio1 27 GPIO_ACTIVE_HIGH>; ti,x-min = /bits/ 16 <0x0>; ti,x-max = /bits/ 16 <0x0fff>; diff --git a/arch/arm/boot/dts/omap3-evm-common.dtsi b/arch/arm/boot/dts/omap3-evm-common.dtsi index b2589f96d5f7..090475083c2f 100644 --- a/arch/arm/boot/dts/omap3-evm-common.dtsi +++ b/arch/arm/boot/dts/omap3-evm-common.dtsi @@ -26,7 +26,7 @@ regulator-name = "vwl1271"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - gpio = <&gpio5 22 0>; /* gpio150 */ + gpio = <&gpio5 22 GPIO_ACTIVE_HIGH>; /* gpio150 */ startup-delay-us = <70000>; enable-active-high; vin-supply = <&vmmc2>; @@ -91,7 +91,7 @@ tsc2046@0 { interrupt-parent = <&gpio6>; interrupts = <15 0>; /* gpio175 */ - pendown-gpio = <&gpio6 15 0>; + pendown-gpio = <&gpio6 15 GPIO_ACTIVE_HIGH>; }; }; diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi index 7166d8876ea8..e14d15e5abc8 100644 --- a/arch/arm/boot/dts/omap3-gta04.dtsi +++ b/arch/arm/boot/dts/omap3-gta04.dtsi @@ -77,10 +77,10 @@ pinctrl-names = "default"; pinctrl-0 = <&spi_gpio_pins>; - gpio-sck = <&gpio1 12 0>; - gpio-miso = <&gpio1 18 0>; - gpio-mosi = <&gpio1 20 0>; - cs-gpios = <&gpio1 19 0>; + gpio-sck = <&gpio1 12 GPIO_ACTIVE_HIGH>; + gpio-miso = <&gpio1 18 GPIO_ACTIVE_HIGH>; + gpio-mosi = <&gpio1 20 GPIO_ACTIVE_HIGH>; + cs-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; num-chipselects = <1>; /* lcd panel */ @@ -118,7 +118,7 @@ tv_amp: opa362 { compatible = "ti,opa362"; - enable-gpios = <&gpio1 23 0>; + enable-gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>; ports { #address-cells = <1>; diff --git a/arch/arm/boot/dts/omap3-gta04a5.dts b/arch/arm/boot/dts/omap3-gta04a5.dts index 52b386f6865b..600b6ca5a1bd 100644 --- a/arch/arm/boot/dts/omap3-gta04a5.dts +++ b/arch/arm/boot/dts/omap3-gta04a5.dts @@ -12,6 +12,6 @@ model = "Goldelico GTA04A5"; sound { - ti,jack-det-gpio = <&twl_gpio 2 0>; /* GTA04A5 only */ + ti,jack-det-gpio = <&twl_gpio 2 GPIO_ACTIVE_HIGH>; /* GTA04A5 only */ }; }; diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index 2230e1c03320..3caf062f882c 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -1,7 +1,7 @@ /* * Common device tree for IGEP boards based on AM/DM37x * - * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk> + * Copyright (C) 2012 Javier Martinez Canillas <javier@osg.samsung.com> * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com> * * This program is free software; you can redistribute it and/or modify @@ -35,60 +35,60 @@ &omap3_pmx_core { uart1_pins: pinmux_uart1_pins { pinctrl-single,pins = < - 0x152 (PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */ - 0x14c (PIN_OUTPUT |MUX_MODE0) /* uart1_tx.uart1_tx */ + OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */ + OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_tx */ >; }; uart3_pins: pinmux_uart3_pins { pinctrl-single,pins = < - 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx.uart3_rx */ - 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx.uart3_tx */ + OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx.uart3_rx */ + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx.uart3_tx */ >; }; mcbsp2_pins: pinmux_mcbsp2_pins { pinctrl-single,pins = < - 0x10c (PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx.mcbsp2_fsx */ - 0x10e (PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx.mcbsp2_clkx */ - 0x110 (PIN_INPUT | MUX_MODE0) /* mcbsp2_dr.mcbsp2.dr */ - 0x112 (PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx.mcbsp2_dx */ + OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx.mcbsp2_fsx */ + OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx.mcbsp2_clkx */ + OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr.mcbsp2.dr */ + OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx.mcbsp2_dx */ >; }; mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < - 0x114 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ - 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ - 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ - 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ - 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ - 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ >; }; mmc2_pins: pinmux_mmc2_pins { pinctrl-single,pins = < - 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ - 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ - 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ - 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ - 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ - 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ >; }; i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < - 0x18a (PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ - 0x18c (PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ + OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ + OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ >; }; i2c3_pins: pinmux_i2c3_pins { pinctrl-single,pins = < - 0x192 (PIN_INPUT | MUX_MODE0) /* i2c3_scl.i2c3_scl */ - 0x194 (PIN_INPUT | MUX_MODE0) /* i2c3_sda.i2c3_sda */ + OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl.i2c3_scl */ + OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda.i2c3_sda */ >; }; }; @@ -155,7 +155,7 @@ twl_audio: audio { compatible = "ti,twl4030-audio"; codec { - }; + }; }; }; }; @@ -175,11 +175,11 @@ }; &mmc1 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins>; - vmmc-supply = <&vmmc1>; - vmmc_aux-supply = <&vsim>; - bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <&vmmc1>; + vmmc_aux-supply = <&vsim>; + bus-width = <4>; }; &mmc3 { @@ -187,13 +187,13 @@ }; &uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_pins>; + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; }; &uart3 { - pinctrl-names = "default"; - pinctrl-0 = <&uart3_pins>; + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; }; &twl_gpio { diff --git a/arch/arm/boot/dts/omap3-igep0020-common.dtsi b/arch/arm/boot/dts/omap3-igep0020-common.dtsi index 5ad688c57a00..d90f12c39307 100644 --- a/arch/arm/boot/dts/omap3-igep0020-common.dtsi +++ b/arch/arm/boot/dts/omap3-igep0020-common.dtsi @@ -1,7 +1,7 @@ /* * Common Device Tree Source for IGEPv2 * - * Copyright (C) 2014 Javier Martinez Canillas <javier@collabora.co.uk> + * Copyright (C) 2014 Javier Martinez Canillas <javier@osg.samsung.com> * Copyright (C) 2014 Enric Balletbo i Serra <eballetbo@gmail.com> * * This program is free software; you can redistribute it and/or modify @@ -111,40 +111,40 @@ tfp410_pins: pinmux_tfp410_pins { pinctrl-single,pins = < - 0x196 (PIN_OUTPUT | MUX_MODE4) /* hdq_sio.gpio_170 */ + OMAP3_CORE1_IOPAD(0x21c6, PIN_OUTPUT | MUX_MODE4) /* hdq_sio.gpio_170 */ >; }; dss_dpi_pins: pinmux_dss_dpi_pins { pinctrl-single,pins = < - 0x0a4 (PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ - 0x0a6 (PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ - 0x0a8 (PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ - 0x0aa (PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ - 0x0ac (PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ - 0x0ae (PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ - 0x0b0 (PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ - 0x0b2 (PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ - 0x0b4 (PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ - 0x0b6 (PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ - 0x0b8 (PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ - 0x0ba (PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ - 0x0bc (PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ - 0x0be (PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ - 0x0c0 (PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ - 0x0c2 (PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ - 0x0c4 (PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ - 0x0c6 (PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ - 0x0c8 (PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ - 0x0ca (PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ - 0x0cc (PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ - 0x0ce (PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ - 0x0d0 (PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */ - 0x0d2 (PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */ - 0x0d4 (PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */ - 0x0d6 (PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */ - 0x0d8 (PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */ - 0x0da (PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */ + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ + OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ + OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ + OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ + OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ + OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ + OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ + OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */ + OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */ + OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */ + OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */ + OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */ + OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */ >; }; diff --git a/arch/arm/boot/dts/omap3-igep0020-rev-f.dts b/arch/arm/boot/dts/omap3-igep0020-rev-f.dts index 72f7cdc091fb..321c2b7a4e9f 100644 --- a/arch/arm/boot/dts/omap3-igep0020-rev-f.dts +++ b/arch/arm/boot/dts/omap3-igep0020-rev-f.dts @@ -1,7 +1,7 @@ /* * Device Tree Source for IGEPv2 Rev. F (TI OMAP AM/DM37x) * - * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk> + * Copyright (C) 2012 Javier Martinez Canillas <javier@osg.samsung.com> * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com> * * This program is free software; you can redistribute it and/or modify diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts index fea7f7edb45d..3835e1569c29 100644 --- a/arch/arm/boot/dts/omap3-igep0020.dts +++ b/arch/arm/boot/dts/omap3-igep0020.dts @@ -1,7 +1,7 @@ /* * Device Tree Source for IGEPv2 Rev. C (TI OMAP AM/DM37x) * - * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk> + * Copyright (C) 2012 Javier Martinez Canillas <javier@osg.samsung.com> * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com> * * This program is free software; you can redistribute it and/or modify @@ -45,15 +45,6 @@ OMAP3_CORE1_IOPAD(0x216a, PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat7.gpio_139 - RST_N_B */ >; }; - - uart2_pins: pinmux_uart2_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */ - OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/ - OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ - OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */ - >; - }; }; /* On board Wifi module */ diff --git a/arch/arm/boot/dts/omap3-igep0030-common.dtsi b/arch/arm/boot/dts/omap3-igep0030-common.dtsi index 0cb1527c39d4..640f06603966 100644 --- a/arch/arm/boot/dts/omap3-igep0030-common.dtsi +++ b/arch/arm/boot/dts/omap3-igep0030-common.dtsi @@ -1,7 +1,7 @@ /* * Common Device Tree Source for IGEP COM MODULE * - * Copyright (C) 2014 Javier Martinez Canillas <javier@collabora.co.uk> + * Copyright (C) 2014 Javier Martinez Canillas <javier@osg.samsung.com> * Copyright (C) 2014 Enric Balletbo i Serra <eballetbo@gmail.com> * * This program is free software; you can redistribute it and/or modify diff --git a/arch/arm/boot/dts/omap3-igep0030-rev-g.dts b/arch/arm/boot/dts/omap3-igep0030-rev-g.dts index b899e341874a..76dc08868bfb 100644 --- a/arch/arm/boot/dts/omap3-igep0030-rev-g.dts +++ b/arch/arm/boot/dts/omap3-igep0030-rev-g.dts @@ -1,7 +1,7 @@ /* * Device Tree Source for IGEP COM MODULE Rev. G (TI OMAP AM/DM37x) * - * Copyright (C) 2014 Javier Martinez Canillas <javier@collabora.co.uk> + * Copyright (C) 2014 Javier Martinez Canillas <javier@osg.samsung.com> * Copyright (C) 2014 Enric Balletbo i Serra <eballetbo@gmail.com> * * This program is free software; you can redistribute it and/or modify diff --git a/arch/arm/boot/dts/omap3-igep0030.dts b/arch/arm/boot/dts/omap3-igep0030.dts index 8150f47ccdf5..468608dab30a 100644 --- a/arch/arm/boot/dts/omap3-igep0030.dts +++ b/arch/arm/boot/dts/omap3-igep0030.dts @@ -1,7 +1,7 @@ /* * Device Tree Source for IGEP COM MODULE Rev. E (TI OMAP AM/DM37x) * - * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk> + * Copyright (C) 2012 Javier Martinez Canillas <javier@osg.samsung.com> * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com> * * This program is free software; you can redistribute it and/or modify diff --git a/arch/arm/boot/dts/omap3-ldp.dts b/arch/arm/boot/dts/omap3-ldp.dts index bd6e6769c7ce..d2fab8c0d4f8 100644 --- a/arch/arm/boot/dts/omap3-ldp.dts +++ b/arch/arm/boot/dts/omap3-ldp.dts @@ -200,7 +200,7 @@ tsc2046@0 { interrupt-parent = <&gpio2>; interrupts = <22 0>; /* gpio54 */ - pendown-gpio = <&gpio2 22 0>; + pendown-gpio = <&gpio2 22 GPIO_ACTIVE_HIGH>; }; }; diff --git a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi index d0dd0365bfda..57d7c93cc72b 100644 --- a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi +++ b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi @@ -284,7 +284,7 @@ }; &mmc1 { - cd-gpios = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>; + cd-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>; cd-inverted; vmmc-supply = <&vmmc1>; bus-width = <4>; @@ -314,7 +314,7 @@ interrupt-parent = <&gpio1>; interrupts = <8 0>; /* boot6 / gpio_8 */ spi-max-frequency = <1000000>; - pendown-gpio = <&gpio1 8 0>; + pendown-gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>; vcc-supply = <®_vcc3>; pinctrl-names = "default"; pinctrl-0 = <&tsc2048_pins>; diff --git a/arch/arm/boot/dts/omap3-lilly-dbb056.dts b/arch/arm/boot/dts/omap3-lilly-dbb056.dts index 834f7c65f62d..0e3c9812f4e3 100644 --- a/arch/arm/boot/dts/omap3-lilly-dbb056.dts +++ b/arch/arm/boot/dts/omap3-lilly-dbb056.dts @@ -114,8 +114,8 @@ status = "okay"; bus-width = <4>; vmmc-supply = <&vmmc1>; - cd-gpios = <&gpio6 4 0>; /* gpio_164 */ - wp-gpios = <&gpio6 3 0>; /* gpio_163 */ + cd-gpios = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* gpio_164 */ + wp-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* gpio_163 */ pinctrl-names = "default"; pinctrl-0 = <&mmc2_pins>; ti,dual-volt; diff --git a/arch/arm/boot/dts/omap3-n950-n9.dtsi b/arch/arm/boot/dts/omap3-n950-n9.dtsi index 800b379d368d..e9ee1df0e467 100644 --- a/arch/arm/boot/dts/omap3-n950-n9.dtsi +++ b/arch/arm/boot/dts/omap3-n950-n9.dtsi @@ -27,7 +27,7 @@ regulator-name = "VEMMC"; regulator-min-microvolt = <2900000>; regulator-max-microvolt = <2900000>; - gpio = <&gpio5 29 0>; /* gpio line 157 */ + gpio = <&gpio5 29 GPIO_ACTIVE_HIGH>; /* gpio line 157 */ startup-delay-us = <150>; enable-active-high; }; diff --git a/arch/arm/boot/dts/omap3-overo-base.dtsi b/arch/arm/boot/dts/omap3-overo-base.dtsi index 28430f1596f2..a29ad16cc9bb 100644 --- a/arch/arm/boot/dts/omap3-overo-base.dtsi +++ b/arch/arm/boot/dts/omap3-overo-base.dtsi @@ -35,7 +35,7 @@ regulator-name = "hsusb2_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - gpio = <&gpio6 8 0>; /* gpio_168: vbus enable */ + gpio = <&gpio6 8 GPIO_ACTIVE_HIGH>; /* gpio_168: vbus enable */ startup-delay-us = <70000>; enable-active-high; }; diff --git a/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi b/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi index 80d236ac64a5..b09cedf66117 100644 --- a/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi +++ b/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi @@ -152,7 +152,7 @@ interrupt-parent = <&gpio4>; interrupts = <18 0>; /* gpio_114 */ - pendown-gpio = <&gpio4 18 0>; + pendown-gpio = <&gpio4 18 GPIO_ACTIVE_HIGH>; ti,x-min = /bits/ 16 <0x0>; ti,x-max = /bits/ 16 <0x0fff>; diff --git a/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi b/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi index 048fd216970a..5f979590571b 100644 --- a/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi +++ b/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi @@ -163,7 +163,7 @@ interrupt-parent = <&gpio4>; interrupts = <18 0>; /* gpio_114 */ - pendown-gpio = <&gpio4 18 0>; + pendown-gpio = <&gpio4 18 GPIO_ACTIVE_HIGH>; ti,x-min = /bits/ 16 <0x0>; ti,x-max = /bits/ 16 <0x0fff>; diff --git a/arch/arm/boot/dts/omap3-pandora-common.dtsi b/arch/arm/boot/dts/omap3-pandora-common.dtsi index f2084e6d01e7..cfe140c657e7 100644 --- a/arch/arm/boot/dts/omap3-pandora-common.dtsi +++ b/arch/arm/boot/dts/omap3-pandora-common.dtsi @@ -218,7 +218,7 @@ regulator-always-on; regulator-boot-on; enable-active-high; - gpio = <&gpio6 4 0>; /* GPIO_164 */ + gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* GPIO_164 */ }; /* wg7210 (wifi+bt module) 32k clock buffer */ @@ -607,7 +607,7 @@ pinctrl-0 = <&penirq_pins>; interrupt-parent = <&gpio3>; interrupts = <30 0>; /* GPIO_94 */ - pendown-gpio = <&gpio3 30 0>; + pendown-gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; vcc-supply = <&vaux4>; ti,x-min = /bits/ 16 <0>; diff --git a/arch/arm/boot/dts/omap3-tao3530.dtsi b/arch/arm/boot/dts/omap3-tao3530.dtsi index 7bd8d9a4f67f..ae5dbbd9d569 100644 --- a/arch/arm/boot/dts/omap3-tao3530.dtsi +++ b/arch/arm/boot/dts/omap3-tao3530.dtsi @@ -37,7 +37,7 @@ regulator-name = "hsusb2_vbus"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - gpio = <&twl_gpio 18 0>; /* GPIO LEDA */ + gpio = <&twl_gpio 18 GPIO_ACTIVE_HIGH>; /* GPIO LEDA */ startup-delay-us = <70000>; }; @@ -225,7 +225,7 @@ pinctrl-0 = <&mmc1_pins>; vmmc-supply = <&vmmc1>; vmmc_aux-supply = <&vsim>; - cd-gpios = <&twl_gpio 0 0>; + cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_HIGH>; bus-width = <8>; }; diff --git a/arch/arm/boot/dts/omap3-zoom3.dts b/arch/arm/boot/dts/omap3-zoom3.dts index 131448d86e67..7bc5fdd6981e 100644 --- a/arch/arm/boot/dts/omap3-zoom3.dts +++ b/arch/arm/boot/dts/omap3-zoom3.dts @@ -44,7 +44,7 @@ regulator-name = "vwl1271"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - gpio = <&gpio4 5 0>; /* gpio101 */ + gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* gpio101 */ startup-delay-us = <70000>; enable-active-high; }; diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index f1507bc8737e..18d096696fc0 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -68,7 +68,7 @@ regulator-name = "hsusb1_vbus"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - gpio = <&gpio1 1 0>; /* gpio_1 */ + gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; /* gpio_1 */ startup-delay-us = <70000>; enable-active-high; /* @@ -98,7 +98,7 @@ regulator-name = "vwl1271"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - gpio = <&gpio2 11 0>; + gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>; startup-delay-us = <70000>; enable-active-high; }; diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index dac86ed7481f..f0bdc41f8eff 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -30,7 +30,7 @@ regulator-name = "VDD_ETH"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - gpio = <&gpio2 16 0>; /* gpio line 48 */ + gpio = <&gpio2 16 GPIO_ACTIVE_HIGH>; /* gpio line 48 */ enable-active-high; regulator-boot-on; }; @@ -155,7 +155,7 @@ regulator-name = "vwl1271"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - gpio = <&gpio2 22 0>; + gpio = <&gpio2 22 GPIO_ACTIVE_HIGH>; startup-delay-us = <70000>; enable-active-high; }; @@ -374,7 +374,7 @@ /* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */ interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */ - ti,audpwron-gpio = <&gpio4 31 0>; /* gpio line 127 */ + ti,audpwron-gpio = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio line 127 */ vio-supply = <&v1v8>; v2v1-supply = <&v2v1>; diff --git a/arch/arm/boot/dts/omap4-var-som-om44-wlan.dtsi b/arch/arm/boot/dts/omap4-var-som-om44-wlan.dtsi index 9bceeb7e1f03..1c5f6f35e1cf 100644 --- a/arch/arm/boot/dts/omap4-var-som-om44-wlan.dtsi +++ b/arch/arm/boot/dts/omap4-var-som-om44-wlan.dtsi @@ -15,7 +15,7 @@ regulator-name = "vwl1271"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - gpio = <&gpio2 11 0>; /* gpio 43 */ + gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>; /* gpio 43 */ startup-delay-us = <70000>; enable-active-high; }; diff --git a/arch/arm/boot/dts/omap4-var-som-om44.dtsi b/arch/arm/boot/dts/omap4-var-som-om44.dtsi index a4f1ba2e1903..49d032b846be 100644 --- a/arch/arm/boot/dts/omap4-var-som-om44.dtsi +++ b/arch/arm/boot/dts/omap4-var-som-om44.dtsi @@ -196,7 +196,7 @@ /* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */ interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */ - ti,audpwron-gpio = <&gpio6 22 0>; /* gpio 182 */ + ti,audpwron-gpio = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* gpio 182 */ vio-supply = <&v1v8>; v2v1-supply = <&v2v1>; diff --git a/arch/arm/boot/dts/omap4460.dtsi b/arch/arm/boot/dts/omap4460.dtsi index 194f9ef0a009..5fa68f191af7 100644 --- a/arch/arm/boot/dts/omap4460.dtsi +++ b/arch/arm/boot/dts/omap4460.dtsi @@ -46,7 +46,7 @@ 0x4a002378 0x18>; compatible = "ti,omap4460-bandgap"; interrupts = <0 126 IRQ_TYPE_LEVEL_HIGH>; /* talert */ - gpios = <&gpio3 22 0>; /* tshut */ + gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>; /* tshut */ #thermal-sensor-cells = <0>; }; diff --git a/arch/arm/boot/dts/omap5-board-common.dtsi b/arch/arm/boot/dts/omap5-board-common.dtsi new file mode 100644 index 000000000000..5cf76a1c5c75 --- /dev/null +++ b/arch/arm/boot/dts/omap5-board-common.dtsi @@ -0,0 +1,655 @@ +/* + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include "omap5.dtsi" +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> + +/ { + aliases { + display0 = &hdmi0; + }; + + vmmcsd_fixed: fixedregulator-mmcsd { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + mmc3_pwrseq: sdhci0_pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&clk32kgaudio>; + clock-names = "ext_clock"; + }; + + vmmcsdio_fixed: fixedregulator-mmcsdio { + compatible = "regulator-fixed"; + regulator-name = "vmmcsdio_fixed"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>; /* gpio140 WLAN_EN */ + enable-active-high; + startup-delay-us = <70000>; + pinctrl-names = "default"; + pinctrl-0 = <&wlan_pins>; + }; + + /* HS USB Host PHY on PORT 2 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */ + clocks = <&auxclk1_ck>; + clock-names = "main_clk"; + clock-frequency = <19200000>; + }; + + /* HS USB Host PHY on PORT 3 */ + hsusb3_phy: hsusb3_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */ + }; + + leds { + compatible = "gpio-leds"; + led@1 { + label = "omap5:blue:usr1"; + gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */ + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + }; + + tpd12s015: encoder@0 { + compatible = "ti,tpd12s015"; + + pinctrl-names = "default"; + pinctrl-0 = <&tpd12s015_pins>; + + /* gpios defined in the board specific dts */ + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tpd12s015_in: endpoint@0 { + remote-endpoint = <&hdmi_out>; + }; + }; + + port@1 { + reg = <1>; + + tpd12s015_out: endpoint@0 { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; + }; + + hdmi0: connector@0 { + compatible = "hdmi-connector"; + label = "hdmi"; + + type = "b"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&tpd12s015_out>; + }; + }; + }; + + sound: sound { + compatible = "ti,abe-twl6040"; + ti,model = "omap5-uevm"; + + ti,mclk-freq = <19200000>; + + ti,mcpdm = <&mcpdm>; + + ti,twl6040 = <&twl6040>; + + /* Audio routing */ + ti,audio-routing = + "Headset Stereophone", "HSOL", + "Headset Stereophone", "HSOR", + "Line Out", "AUXL", + "Line Out", "AUXR", + "HSMIC", "Headset Mic", + "Headset Mic", "Headset Mic Bias", + "AFML", "Line In", + "AFMR", "Line In"; + }; +}; + +&omap5_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &usbhost_pins + &led_gpio_pins + >; + + twl6040_pins: pinmux_twl6040_pins { + pinctrl-single,pins = < + 0x17e (PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */ + >; + }; + + mcpdm_pins: pinmux_mcpdm_pins { + pinctrl-single,pins = < + 0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ + 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */ + 0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */ + 0x160 (PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */ + 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */ + >; + }; + + mcbsp1_pins: pinmux_mcbsp1_pins { + pinctrl-single,pins = < + 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */ + 0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */ + 0x150 (PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */ + 0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */ + >; + }; + + mcbsp2_pins: pinmux_mcbsp2_pins { + pinctrl-single,pins = < + 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */ + 0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */ + 0x158 (PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */ + 0x15a (PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + 0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ + 0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ + >; + }; + + mcspi2_pins: pinmux_mcspi2_pins { + pinctrl-single,pins = < + 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ + 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ + 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */ + 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */ + >; + }; + + mcspi3_pins: pinmux_mcspi3_pins { + pinctrl-single,pins = < + 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi3_somi */ + 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */ + 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi3_simo */ + 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi3_clk */ + >; + }; + + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */ + OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */ + OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */ + OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */ + OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */ + OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */ + >; + }; + + wlan_pins: pinmux_wlan_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */ + >; + }; + + usbhost_pins: pinmux_usbhost_pins { + pinctrl-single,pins = < + 0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */ + 0x86 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */ + + 0x19e (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */ + 0x1a0 (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */ + + 0x70 (PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */ + 0x6e (PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */ + >; + }; + + led_gpio_pins: pinmux_led_gpio_pins { + pinctrl-single,pins = < + 0x196 (PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */ + >; + }; + + uart1_pins: pinmux_uart1_pins { + pinctrl-single,pins = < + 0x60 (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */ + 0x62 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */ + 0x64 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */ + 0x66 (PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */ + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + 0x19a (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */ + 0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */ + >; + }; + + uart5_pins: pinmux_uart5_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */ + 0x172 (PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */ + 0x174 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */ + 0x176 (PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */ + >; + }; + + dss_hdmi_pins: pinmux_dss_hdmi_pins { + pinctrl-single,pins = < + 0x0fc (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + 0x100 (PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */ + 0x102 (PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */ + >; + }; + + tpd12s015_pins: pinmux_tpd12s015_pins { + pinctrl-single,pins = < + 0x0fe (PIN_INPUT_PULLDOWN | MUX_MODE6) /* hdmi_hpd.gpio7_193 */ + >; + }; +}; + +&omap5_pmx_wkup { + pinctrl-names = "default"; + pinctrl-0 = < + &usbhost_wkup_pins + >; + + usbhost_wkup_pins: pinmux_usbhost_wkup_pins { + pinctrl-single,pins = < + 0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */ + >; + }; + + wlcore_irq_pin: pinmux_wlcore_irq_pin { + pinctrl-single,pins = < + OMAP5_IOPAD(0x040, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */ + >; + }; +}; + +&mmc1 { + vmmc-supply = <&ldo9_reg>; + bus-width = <4>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <8>; + ti,non-removable; +}; + +&mmc3 { + vmmc-supply = <&vmmcsdio_fixed>; + mmc-pwrseq = <&mmc3_pwrseq>; + bus-width = <4>; + non-removable; + cap-power-off-card; + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins &wlcore_irq_pin>; + interrupts-extended = <&gic GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH + &omap5_pmx_core 0x168>; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1271"; + reg = <2>; + interrupt-parent = <&gpio1>; + interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; /* gpio 14 */ + ref-clock-frequency = <26000000>; + }; +}; + +&mmc4 { + status = "disabled"; +}; + +&mmc5 { + status = "disabled"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + + clock-frequency = <400000>; + + palmas: palmas@48 { + compatible = "ti,palmas"; + interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */ + reg = <0x48>; + interrupt-controller; + #interrupt-cells = <2>; + ti,system-power-controller; + + extcon_usb3: palmas_usb { + compatible = "ti,palmas-usb-vid"; + ti,enable-vbus-detection; + ti,enable-id-detection; + ti,wakeup; + }; + + clk32kgaudio: palmas_clk32k@1 { + compatible = "ti,palmas-clk32kgaudio"; + #clock-cells = <0>; + }; + + palmas_pmic { + compatible = "ti,palmas-pmic"; + interrupt-parent = <&palmas>; + interrupts = <14 IRQ_TYPE_NONE>; + interrupt-name = "short-irq"; + + ti,ldo6-vibrator; + + regulators { + smps123_reg: smps123 { + /* VDD_OPP_MPU */ + regulator-name = "smps123"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + smps45_reg: smps45 { + /* VDD_OPP_MM */ + regulator-name = "smps45"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1310000>; + regulator-always-on; + regulator-boot-on; + }; + + smps6_reg: smps6 { + /* VDD_DDR3 - over VDD_SMPS6 */ + regulator-name = "smps6"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + smps7_reg: smps7 { + /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */ + regulator-name = "smps7"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + smps8_reg: smps8 { + /* VDD_OPP_CORE */ + regulator-name = "smps8"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1310000>; + regulator-always-on; + regulator-boot-on; + }; + + smps9_reg: smps9 { + /* VDDA_2v1_AUD over VDD_2v1 */ + regulator-name = "smps9"; + regulator-min-microvolt = <2100000>; + regulator-max-microvolt = <2100000>; + ti,smps-range = <0x80>; + }; + + smps10_out2_reg: smps10_out2 { + /* VBUS_5V_OTG */ + regulator-name = "smps10_out2"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + smps10_out1_reg: smps10_out1 { + /* VBUS_5V_OTG */ + regulator-name = "smps10_out1"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + ldo1_reg: ldo1 { + /* VDDAPHY_CAM: vdda_csiport */ + regulator-name = "ldo1"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; + }; + + ldo2_reg: ldo2 { + /* VCC_2V8_DISP: Does not go anywhere */ + regulator-name = "ldo2"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + /* Unused */ + status = "disabled"; + }; + + ldo3_reg: ldo3 { + /* VDDAPHY_MDM: vdda_lli */ + regulator-name = "ldo3"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + /* Only if Modem is used */ + status = "disabled"; + }; + + ldo4_reg: ldo4 { + /* VDDAPHY_DISP: vdda_dsiport/hdmi */ + regulator-name = "ldo4"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; + }; + + ldo5_reg: ldo5 { + /* VDDA_1V8_PHY: usb/sata/hdmi.. */ + regulator-name = "ldo5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo6_reg: ldo6 { + /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */ + regulator-name = "ldo6"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo7_reg: ldo7 { + /* VDD_VPP: vpp1 */ + regulator-name = "ldo7"; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + /* Only for efuse reprograming! */ + status = "disabled"; + }; + + ldo8_reg: ldo8 { + /* VDD_3v0: Does not go anywhere */ + regulator-name = "ldo8"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + /* Unused */ + status = "disabled"; + }; + + ldo9_reg: ldo9 { + /* VCC_DV_SDIO: vdds_sdcard */ + regulator-name = "ldo9"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + }; + + ldoln_reg: ldoln { + /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */ + regulator-name = "ldoln"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldousb_reg: ldousb { + /* VDDA_3V_USB: VDDA_USBHS33 */ + regulator-name = "ldousb"; + regulator-min-microvolt = <3250000>; + regulator-max-microvolt = <3250000>; + regulator-always-on; + regulator-boot-on; + }; + + regen3_reg: regen3 { + /* REGEN3 controls LDO9 supply to card */ + regulator-name = "regen3"; + regulator-always-on; + regulator-boot-on; + }; + }; + }; + + palmas_power_button: palmas_power_button { + compatible = "ti,palmas-pwrbutton"; + interrupt-parent = <&palmas>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + }; + }; + + twl6040: twl@4b { + compatible = "ti,twl6040"; + reg = <0x4b>; + + pinctrl-names = "default"; + pinctrl-0 = <&twl6040_pins>; + + interrupts = <GIC_SPI 119 IRQ_TYPE_NONE>; /* IRQ_SYS_2N cascaded to gic */ + ti,audpwron-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>; /* gpio line 141 */ + + vio-supply = <&smps7_reg>; + v2v1-supply = <&smps9_reg>; + enable-active-high; + + clocks = <&clk32kgaudio>; + clock-names = "clk32k"; + }; +}; + +&mcpdm { + pinctrl-names = "default"; + pinctrl-0 = <&mcpdm_pins>; + status = "okay"; +}; + +&mcbsp1 { + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp1_pins>; + status = "okay"; +}; + +&mcbsp2 { + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp2_pins>; + status = "okay"; +}; + +&usbhshost { + port2-mode = "ehci-hsic"; + port3-mode = "ehci-hsic"; +}; + +&usbhsehci { + phys = <0 &hsusb2_phy &hsusb3_phy>; +}; + +&usb3 { + extcon = <&extcon_usb3>; + vbus-supply = <&smps10_out1_reg>; +}; + +&mcspi1 { + +}; + +&mcspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&mcspi2_pins>; +}; + +&mcspi3 { + pinctrl-names = "default"; + pinctrl-0 = <&mcspi3_pins>; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; + interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, + <&omap5_pmx_core 0x19c>; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&uart5_pins>; +}; + +&cpu0 { + cpu0-supply = <&smps123_reg>; +}; + +&dss { + status = "ok"; +}; + +&hdmi { + status = "ok"; + + /* vdda-supply populated in board specific dts file */ + + pinctrl-names = "default"; + pinctrl-0 = <&dss_hdmi_pins>; + + port { + hdmi_out: endpoint { + remote-endpoint = <&tpd12s015_in>; + }; + }; +}; diff --git a/arch/arm/boot/dts/omap5-cm-t54.dts b/arch/arm/boot/dts/omap5-cm-t54.dts index 61ad2ea34720..3774b37be6c8 100644 --- a/arch/arm/boot/dts/omap5-cm-t54.dts +++ b/arch/arm/boot/dts/omap5-cm-t54.dts @@ -344,7 +344,7 @@ interrupt-parent = <&gpio1>; interrupts = <15 0>; /* gpio1_wk15 */ - pendown-gpio = <&gpio1 15 0>; + pendown-gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>; ti,x-min = /bits/ 16 <0x0>; diff --git a/arch/arm/boot/dts/omap5-igep0050.dts b/arch/arm/boot/dts/omap5-igep0050.dts new file mode 100644 index 000000000000..46ecb1dd3b5c --- /dev/null +++ b/arch/arm/boot/dts/omap5-igep0050.dts @@ -0,0 +1,54 @@ +/* + * Copyright (C) 2013 ISEE 2007 SL - http://www.isee.biz/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "omap5-board-common.dtsi" + +/ { + model = "IGEPv5"; + compatible = "isee,omap5-igep0050", "ti,omap5"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x7f000000>; /* 2032 MB */ + }; +}; + +&hdmi { + vdda-supply = <&ldo7_reg>; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins>; + + tca6416: tca6416@21 { + compatible = "ti,tca6416"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + +&omap5_pmx_core { + i2c4_pins: pinmux_i2c4_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0) /* i2c4_scl */ + OMAP5_IOPAD(0x0fa, PIN_INPUT | MUX_MODE0) /* i2c4_sda */ + >; + }; +}; + +&tpd12s015 { + gpios = <&tca6416 11 0>, /* TCA6416 P01, CT_CP_HDP */ + <&tca6416 12 0>, /* TCA6416 P00, LS_OE*/ + <&gpio7 1 0>, /* 193, HPD */ + <&gpio7 2 0>, /* 194, SCL */ + <&gpio7 3 0>; /* 195, SDA */ +}; + diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index 3cb030f9d2c4..05b1c1ebded8 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -7,9 +7,7 @@ */ /dts-v1/; -#include "omap5.dtsi" -#include <dt-bindings/interrupt-controller/irq.h> -#include <dt-bindings/interrupt-controller/arm-gic.h> +#include "omap5-board-common.dtsi" / { model = "TI OMAP5 uEVM board"; @@ -19,523 +17,10 @@ device_type = "memory"; reg = <0x80000000 0x7F000000>; /* 2032 MB */ }; - - aliases { - display0 = &hdmi0; - }; - - vmmcsd_fixed: fixedregulator-mmcsd { - compatible = "regulator-fixed"; - regulator-name = "vmmcsd_fixed"; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - }; - - /* HS USB Host PHY on PORT 2 */ - hsusb2_phy: hsusb2_phy { - compatible = "usb-nop-xceiv"; - reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */ - clocks = <&auxclk1_ck>; - clock-names = "main_clk"; - clock-frequency = <19200000>; - }; - - /* HS USB Host PHY on PORT 3 */ - hsusb3_phy: hsusb3_phy { - compatible = "usb-nop-xceiv"; - reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */ - }; - - leds { - compatible = "gpio-leds"; - led@1 { - label = "omap5:blue:usr1"; - gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */ - linux,default-trigger = "heartbeat"; - default-state = "off"; - }; - }; - - tpd12s015: encoder@0 { - compatible = "ti,tpd12s015"; - - pinctrl-names = "default"; - pinctrl-0 = <&tpd12s015_pins>; - - gpios = <&gpio9 0 GPIO_ACTIVE_HIGH>, /* TCA6424A P01, CT CP HPD */ - <&gpio9 1 GPIO_ACTIVE_HIGH>, /* TCA6424A P00, LS OE */ - <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */ - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - - tpd12s015_in: endpoint@0 { - remote-endpoint = <&hdmi_out>; - }; - }; - - port@1 { - reg = <1>; - - tpd12s015_out: endpoint@0 { - remote-endpoint = <&hdmi_connector_in>; - }; - }; - }; - }; - - hdmi0: connector@0 { - compatible = "hdmi-connector"; - label = "hdmi"; - - type = "b"; - - port { - hdmi_connector_in: endpoint { - remote-endpoint = <&tpd12s015_out>; - }; - }; - }; - - sound: sound { - compatible = "ti,abe-twl6040"; - ti,model = "omap5-uevm"; - - ti,mclk-freq = <19200000>; - - ti,mcpdm = <&mcpdm>; - - ti,twl6040 = <&twl6040>; - - /* Audio routing */ - ti,audio-routing = - "Headset Stereophone", "HSOL", - "Headset Stereophone", "HSOR", - "Line Out", "AUXL", - "Line Out", "AUXR", - "HSMIC", "Headset Mic", - "Headset Mic", "Headset Mic Bias", - "AFML", "Line In", - "AFMR", "Line In"; - }; -}; - -&omap5_pmx_core { - pinctrl-names = "default"; - pinctrl-0 = < - &usbhost_pins - &led_gpio_pins - >; - - twl6040_pins: pinmux_twl6040_pins { - pinctrl-single,pins = < - 0x17e (PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */ - >; - }; - - mcpdm_pins: pinmux_mcpdm_pins { - pinctrl-single,pins = < - 0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ - 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */ - 0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */ - 0x160 (PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */ - 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */ - >; - }; - - mcbsp1_pins: pinmux_mcbsp1_pins { - pinctrl-single,pins = < - 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */ - 0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */ - 0x150 (PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */ - 0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */ - >; - }; - - mcbsp2_pins: pinmux_mcbsp2_pins { - pinctrl-single,pins = < - 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */ - 0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */ - 0x158 (PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */ - 0x15a (PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */ - >; - }; - - i2c1_pins: pinmux_i2c1_pins { - pinctrl-single,pins = < - 0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ - 0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ - >; - }; - - i2c5_pins: pinmux_i2c5_pins { - pinctrl-single,pins = < - 0x186 (PIN_INPUT | MUX_MODE0) /* i2c5_scl */ - 0x188 (PIN_INPUT | MUX_MODE0) /* i2c5_sda */ - >; - }; - - mcspi2_pins: pinmux_mcspi2_pins { - pinctrl-single,pins = < - 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ - 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ - 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */ - 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */ - >; - }; - - mcspi3_pins: pinmux_mcspi3_pins { - pinctrl-single,pins = < - 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi3_somi */ - 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */ - 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi3_simo */ - 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi3_clk */ - >; - }; - - mcspi4_pins: pinmux_mcspi4_pins { - pinctrl-single,pins = < - 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi4_clk */ - 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi4_simo */ - 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi4_somi */ - 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi4_cs0 */ - >; - }; - - usbhost_pins: pinmux_usbhost_pins { - pinctrl-single,pins = < - 0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */ - 0x86 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */ - - 0x19e (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */ - 0x1a0 (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */ - - 0x70 (PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */ - 0x6e (PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */ - >; - }; - - led_gpio_pins: pinmux_led_gpio_pins { - pinctrl-single,pins = < - 0x196 (PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */ - >; - }; - - uart1_pins: pinmux_uart1_pins { - pinctrl-single,pins = < - 0x60 (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */ - 0x62 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */ - 0x64 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */ - 0x66 (PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */ - >; - }; - - uart3_pins: pinmux_uart3_pins { - pinctrl-single,pins = < - 0x19a (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */ - 0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */ - >; - }; - - uart5_pins: pinmux_uart5_pins { - pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */ - 0x172 (PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */ - 0x174 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */ - 0x176 (PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */ - >; - }; - - dss_hdmi_pins: pinmux_dss_hdmi_pins { - pinctrl-single,pins = < - 0x0fc (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ - 0x100 (PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */ - 0x102 (PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */ - >; - }; - - tpd12s015_pins: pinmux_tpd12s015_pins { - pinctrl-single,pins = < - 0x0fe (PIN_INPUT_PULLDOWN | MUX_MODE6) /* hdmi_hpd.gpio7_193 */ - >; - }; -}; - -&omap5_pmx_wkup { - pinctrl-names = "default"; - pinctrl-0 = < - &usbhost_wkup_pins - >; - - usbhost_wkup_pins: pinmux_usbhost_wkup_pins { - pinctrl-single,pins = < - 0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */ - >; - }; -}; - -&mmc1 { - vmmc-supply = <&ldo9_reg>; - bus-width = <4>; -}; - -&mmc2 { - vmmc-supply = <&vmmcsd_fixed>; - bus-width = <8>; - ti,non-removable; -}; - -&mmc3 { - bus-width = <4>; - ti,non-removable; -}; - -&mmc4 { - status = "disabled"; }; -&mmc5 { - status = "disabled"; -}; - -&i2c1 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins>; - - clock-frequency = <400000>; - - palmas: palmas@48 { - compatible = "ti,palmas"; - interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */ - reg = <0x48>; - interrupt-controller; - #interrupt-cells = <2>; - ti,system-power-controller; - - extcon_usb3: palmas_usb { - compatible = "ti,palmas-usb-vid"; - ti,enable-vbus-detection; - ti,enable-id-detection; - ti,wakeup; - }; - - clk32kgaudio: palmas_clk32k@1 { - compatible = "ti,palmas-clk32kgaudio"; - #clock-cells = <0>; - }; - - palmas_pmic { - compatible = "ti,palmas-pmic"; - interrupt-parent = <&palmas>; - interrupts = <14 IRQ_TYPE_NONE>; - interrupt-name = "short-irq"; - - ti,ldo6-vibrator; - - regulators { - smps123_reg: smps123 { - /* VDD_OPP_MPU */ - regulator-name = "smps123"; - regulator-min-microvolt = < 600000>; - regulator-max-microvolt = <1500000>; - regulator-always-on; - regulator-boot-on; - }; - - smps45_reg: smps45 { - /* VDD_OPP_MM */ - regulator-name = "smps45"; - regulator-min-microvolt = < 600000>; - regulator-max-microvolt = <1310000>; - regulator-always-on; - regulator-boot-on; - }; - - smps6_reg: smps6 { - /* VDD_DDR3 - over VDD_SMPS6 */ - regulator-name = "smps6"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-always-on; - regulator-boot-on; - }; - - smps7_reg: smps7 { - /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */ - regulator-name = "smps7"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - smps8_reg: smps8 { - /* VDD_OPP_CORE */ - regulator-name = "smps8"; - regulator-min-microvolt = < 600000>; - regulator-max-microvolt = <1310000>; - regulator-always-on; - regulator-boot-on; - }; - - smps9_reg: smps9 { - /* VDDA_2v1_AUD over VDD_2v1 */ - regulator-name = "smps9"; - regulator-min-microvolt = <2100000>; - regulator-max-microvolt = <2100000>; - ti,smps-range = <0x80>; - }; - - smps10_out2_reg: smps10_out2 { - /* VBUS_5V_OTG */ - regulator-name = "smps10_out2"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - regulator-boot-on; - }; - - smps10_out1_reg: smps10_out1 { - /* VBUS_5V_OTG */ - regulator-name = "smps10_out1"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - }; - - ldo1_reg: ldo1 { - /* VDDAPHY_CAM: vdda_csiport */ - regulator-name = "ldo1"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1800000>; - }; - - ldo2_reg: ldo2 { - /* VCC_2V8_DISP: Does not go anywhere */ - regulator-name = "ldo2"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - /* Unused */ - status = "disabled"; - }; - - ldo3_reg: ldo3 { - /* VDDAPHY_MDM: vdda_lli */ - regulator-name = "ldo3"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - regulator-boot-on; - /* Only if Modem is used */ - status = "disabled"; - }; - - ldo4_reg: ldo4 { - /* VDDAPHY_DISP: vdda_dsiport/hdmi */ - regulator-name = "ldo4"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1800000>; - }; - - ldo5_reg: ldo5 { - /* VDDA_1V8_PHY: usb/sata/hdmi.. */ - regulator-name = "ldo5"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo6_reg: ldo6 { - /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */ - regulator-name = "ldo6"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo7_reg: ldo7 { - /* VDD_VPP: vpp1 */ - regulator-name = "ldo7"; - regulator-min-microvolt = <2000000>; - regulator-max-microvolt = <2000000>; - /* Only for efuse reprograming! */ - status = "disabled"; - }; - - ldo8_reg: ldo8 { - /* VDD_3v0: Does not go anywhere */ - regulator-name = "ldo8"; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - regulator-boot-on; - /* Unused */ - status = "disabled"; - }; - - ldo9_reg: ldo9 { - /* VCC_DV_SDIO: vdds_sdcard */ - regulator-name = "ldo9"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3000000>; - regulator-boot-on; - }; - - ldoln_reg: ldoln { - /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */ - regulator-name = "ldoln"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - ldousb_reg: ldousb { - /* VDDA_3V_USB: VDDA_USBHS33 */ - regulator-name = "ldousb"; - regulator-min-microvolt = <3250000>; - regulator-max-microvolt = <3250000>; - regulator-always-on; - regulator-boot-on; - }; - - regen3_reg: regen3 { - /* REGEN3 controls LDO9 supply to card */ - regulator-name = "regen3"; - regulator-always-on; - regulator-boot-on; - }; - }; - }; - - palmas_power_button: palmas_power_button { - compatible = "ti,palmas-pwrbutton"; - interrupt-parent = <&palmas>; - interrupts = <1 IRQ_TYPE_EDGE_FALLING>; - wakeup-source; - }; - }; - - twl6040: twl@4b { - compatible = "ti,twl6040"; - reg = <0x4b>; - - pinctrl-names = "default"; - pinctrl-0 = <&twl6040_pins>; - - interrupts = <GIC_SPI 119 IRQ_TYPE_NONE>; /* IRQ_SYS_2N cascaded to gic */ - ti,audpwron-gpio = <&gpio5 13 0>; /* gpio line 141 */ - - vio-supply = <&smps7_reg>; - v2v1-supply = <&smps9_reg>; - enable-active-high; - - clocks = <&clk32kgaudio>; - clock-names = "clk32k"; - }; +&hdmi { + vdda-supply = <&ldo4_reg>; }; &i2c5 { @@ -552,92 +37,17 @@ }; }; -&mcpdm { - pinctrl-names = "default"; - pinctrl-0 = <&mcpdm_pins>; - status = "okay"; -}; - -&mcbsp1 { - pinctrl-names = "default"; - pinctrl-0 = <&mcbsp1_pins>; - status = "okay"; -}; - -&mcbsp2 { - pinctrl-names = "default"; - pinctrl-0 = <&mcbsp2_pins>; - status = "okay"; -}; - -&usbhshost { - port2-mode = "ehci-hsic"; - port3-mode = "ehci-hsic"; -}; - -&usbhsehci { - phys = <0 &hsusb2_phy &hsusb3_phy>; -}; - -&usb3 { - extcon = <&extcon_usb3>; - vbus-supply = <&smps10_out1_reg>; -}; - -&mcspi1 { - -}; - -&mcspi2 { - pinctrl-names = "default"; - pinctrl-0 = <&mcspi2_pins>; -}; - -&mcspi3 { - pinctrl-names = "default"; - pinctrl-0 = <&mcspi3_pins>; -}; - -&mcspi4 { - pinctrl-names = "default"; - pinctrl-0 = <&mcspi4_pins>; -}; - -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_pins>; -}; - -&uart3 { - pinctrl-names = "default"; - pinctrl-0 = <&uart3_pins>; - interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, - <&omap5_pmx_core 0x19c>; -}; - -&uart5 { - pinctrl-names = "default"; - pinctrl-0 = <&uart5_pins>; -}; - -&cpu0 { - cpu0-supply = <&smps123_reg>; -}; - -&dss { - status = "ok"; +&omap5_pmx_core { + i2c5_pins: pinmux_i2c5_pins { + pinctrl-single,pins = < + 0x186 (PIN_INPUT | MUX_MODE0) /* i2c5_scl */ + 0x188 (PIN_INPUT | MUX_MODE0) /* i2c5_sda */ + >; + }; }; -&hdmi { - status = "ok"; - vdda-supply = <&ldo4_reg>; - - pinctrl-names = "default"; - pinctrl-0 = <&dss_hdmi_pins>; - - port { - hdmi_out: endpoint { - remote-endpoint = <&tpd12s015_in>; - }; - }; +&tpd12s015 { + gpios = <&gpio9 0 GPIO_ACTIVE_HIGH>, /* TCA6424A P01, CT CP HPD */ + <&gpio9 1 GPIO_ACTIVE_HIGH>, /* TCA6424A P00, LS OE */ + <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */ }; diff --git a/arch/arm/boot/dts/orion5x.dtsi b/arch/arm/boot/dts/orion5x.dtsi index 75cd01bd6024..e1b6d2a2ac49 100644 --- a/arch/arm/boot/dts/orion5x.dtsi +++ b/arch/arm/boot/dts/orion5x.dtsi @@ -212,6 +212,16 @@ status = "disabled"; }; + cesa: crypto@90000 { + compatible = "marvell,orion-crypto"; + reg = <0x90000 0x10000>; + reg-names = "regs"; + interrupts = <28>; + marvell,crypto-srams = <&crypto_sram>; + marvell,crypto-sram-size = <0x800>; + status = "okay"; + }; + ehci1: ehci@a0000 { compatible = "marvell,orion-ehci"; reg = <0xa0000 0x1000>; @@ -220,13 +230,11 @@ }; }; - cesa: crypto@90000 { - compatible = "marvell,orion-crypto"; - reg = <MBUS_ID(0xf0, 0x01) 0x90000 0x10000>, - <MBUS_ID(0x09, 0x00) 0x0 0x800>; - reg-names = "regs", "sram"; - interrupts = <28>; - status = "okay"; + crypto_sram: sa-sram { + compatible = "mmio-sram"; + reg = <MBUS_ID(0x09, 0x00) 0x0 0x800>; + #address-cells = <1>; + #size-cells = <1>; }; }; }; diff --git a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts index 47c0282bdfca..03784f1366e5 100644 --- a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts +++ b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts @@ -1,4 +1,6 @@ #include "qcom-apq8064-v2.0.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> / { model = "CompuLab CM-QS600"; @@ -12,12 +14,27 @@ stdout-path = "serial0:115200n8"; }; + pwrseq { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "simple-bus"; + + sdcc4_pwrseq: sdcc4_pwrseq { + pinctrl-names = "default"; + pinctrl-0 = <&wlan_default_gpios>; + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>; + }; + }; + soc { pinctrl@800000 { - i2c1_pins: i2c1 { + card_detect: card_detect { mux { - pins = "gpio20", "gpio21"; - function = "gsbi1"; + pins = "gpio26"; + function = "gpio"; + bias-disable; }; }; }; @@ -96,10 +113,8 @@ i2c@12460000 { status = "okay"; clock-frequency = <200000>; - pinctrl-0 = <&i2c1_pins>; - pinctrl-names = "default"; - eeprom: eeprom@50 { + eeprom@50 { compatible = "24c02"; reg = <0x50>; pagesize = <32>; @@ -112,6 +127,8 @@ qcom,mode = <GSBI_PROT_I2C_UART>; serial@16640000 { status = "ok"; + pinctrl-names = "default"; + pinctrl-0 = <&gsbi7_uart_2pins>; }; }; @@ -163,6 +180,21 @@ regulator-always-on; }; + qcom,ssbi@500000 { + pmic@0 { + gpio@150 { + wlan_default_gpios: wlan-gpios { + pios { + pins = "gpio43"; + function = "normal"; + bias-disable; + power-source = <PM8921_GPIO_S4>; + }; + }; + }; + }; + }; + amba { /* eMMC */ sdcc1: sdcc@12400000 { @@ -175,12 +207,16 @@ sdcc3: sdcc@12180000 { status = "okay"; vmmc-supply = <&v3p3_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&card_detect>; + cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>; }; /* WLAN */ sdcc4: sdcc@121c0000 { status = "okay"; vmmc-supply = <&v3p3_fixed>; vqmmc-supply = <&v3p3_fixed>; + mmc-pwrseq = <&sdcc4_pwrseq>; }; }; }; diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts index f3100da082b2..11ac608b6d50 100644 --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts @@ -1,5 +1,6 @@ #include "qcom-apq8064-v2.0.dtsi" #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> / { model = "Qualcomm APQ8064/IFC6410"; @@ -14,6 +15,29 @@ stdout-path = "serial0:115200n8"; }; + pwrseq { + compatible = "simple-bus"; + + sdcc4_pwrseq: sdcc4_pwrseq { + pinctrl-names = "default"; + pinctrl-0 = <&wlan_default_gpios>; + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <¬ify_led>; + + led@1 { + label = "apq8064:green:user1"; + gpios = <&pm8921_gpio 18 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + soc { pinctrl@800000 { card_detect: card_detect { @@ -119,8 +143,6 @@ qcom,mode = <GSBI_PROT_I2C>; i2c3: i2c@16280000 { status = "okay"; - pinctrl-0 = <&i2c3_pins>; - pinctrl-names = "default"; }; }; @@ -131,10 +153,8 @@ i2c@12460000 { status = "okay"; clock-frequency = <200000>; - pinctrl-0 = <&i2c1_pins>; - pinctrl-names = "default"; - eeprom: eeprom@52 { + eeprom@52 { compatible = "atmel,24c128"; reg = <0x52>; pagesize = <32>; @@ -148,9 +168,8 @@ serial@16540000 { status = "ok"; - pinctrl-names = "default"; - pinctrl-0 = <&uart_pins>; + pinctrl-0 = <&gsbi6_uart_4pins>; }; }; @@ -159,6 +178,8 @@ qcom,mode = <GSBI_PROT_I2C_UART>; serial@16640000 { status = "ok"; + pinctrl-names = "default"; + pinctrl-0 = <&gsbi7_uart_2pins>; }; }; @@ -210,6 +231,30 @@ status = "okay"; }; + qcom,ssbi@500000 { + pmic@0 { + gpio@150 { + wlan_default_gpios: wlan-gpios { + pios { + pins = "gpio43"; + function = "normal"; + bias-disable; + power-source = <PM8921_GPIO_S4>; + }; + }; + + notify_led: nled { + pios { + pins = "gpio18"; + function = "normal"; + bias-disable; + power-source = <PM8921_GPIO_S4>; + }; + }; + }; + }; + }; + amba { /* eMMC */ sdcc1: sdcc@12400000 { @@ -231,6 +276,7 @@ status = "okay"; vmmc-supply = <&ext_3p3v>; vqmmc-supply = <&pm8921_lvs1>; + mmc-pwrseq = <&sdcc4_pwrseq>; }; }; }; diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index d2e94d647c27..a4c1762b53ea 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -127,12 +127,33 @@ }; }; - uart_pins: uart_pins { + gsbi6_uart_2pins: gsbi6_uart_2pins { + mux { + pins = "gpio14", "gpio15"; + function = "gsbi6"; + }; + }; + + gsbi6_uart_4pins: gsbi6_uart_4pins { mux { pins = "gpio14", "gpio15", "gpio16", "gpio17"; function = "gsbi6"; }; }; + + gsbi7_uart_2pins: gsbi7_uart_2pins { + mux { + pins = "gpio82", "gpio83"; + function = "gsbi7"; + }; + }; + + gsbi7_uart_4pins: gsbi7_uart_4pins { + mux { + pins = "gpio82", "gpio83", "gpio84", "gpio85"; + function = "gsbi7"; + }; + }; }; intc: interrupt-controller@2000000 { @@ -213,6 +234,8 @@ i2c1: i2c@12460000 { compatible = "qcom,i2c-qup-v1.1.1"; + pinctrl-0 = <&i2c1_pins>; + pinctrl-names = "default"; reg = <0x12460000 0x1000>; interrupts = <0 194 IRQ_TYPE_NONE>; clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; @@ -258,6 +281,8 @@ ranges; i2c3: i2c@16280000 { compatible = "qcom,i2c-qup-v1.1.1"; + pinctrl-0 = <&i2c3_pins>; + pinctrl-names = "default"; reg = <0x16280000 0x1000>; interrupts = <GIC_SPI 151 IRQ_TYPE_NONE>; clocks = <&gcc GSBI3_QUP_CLK>, @@ -361,6 +386,22 @@ <136 1>, <137 1>, <138 1>, <139 1>; }; + rtc@11d { + compatible = "qcom,pm8921-rtc"; + interrupt-parent = <&pmicintc>; + interrupts = <39 1>; + reg = <0x11d>; + allow-set-time; + }; + + pwrkey@1c { + compatible = "qcom,pm8921-pwrkey"; + reg = <0x1c>; + interrupt-parent = <&pmicintc>; + interrupts = <50 1>, <51 1>; + debounce = <15625>; + pull-up; + }; }; }; diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi index 0554fbd72c40..fcffecae3e67 100644 --- a/arch/arm/boot/dts/qcom-apq8084.dtsi +++ b/arch/arm/boot/dts/qcom-apq8084.dtsi @@ -221,6 +221,7 @@ compatible = "qcom,gcc-apq8084"; #clock-cells = <1>; #reset-cells = <1>; + #power-domain-cells = <1>; reg = <0xfc400000 0x4000>; }; diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi index 93e315053bdd..753bdfddd46e 100644 --- a/arch/arm/boot/dts/qcom-msm8974.dtsi +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi @@ -123,6 +123,11 @@ <0xf9002000 0x1000>; }; + apcs: syscon@f9011000 { + compatible = "syscon"; + reg = <0xf9011000 0x1000>; + }; + timer@f9020000 { #address-cells = <1>; #size-cells = <1>; @@ -237,6 +242,7 @@ compatible = "qcom,gcc-msm8974"; #clock-cells = <1>; #reset-cells = <1>; + #power-domain-cells = <1>; reg = <0xfc400000 0x4000>; }; @@ -249,6 +255,7 @@ compatible = "qcom,mmcc-msm8974"; #clock-cells = <1>; #reset-cells = <1>; + #power-domain-cells = <1>; reg = <0xfd8c0000 0x6000>; }; @@ -313,7 +320,7 @@ }; blsp_i2c11: i2c@f9967000 { - status = "disable"; + status = "disabled"; compatible = "qcom,i2c-qup-v2.1.1"; reg = <0xf9967000 0x1000>; interrupts = <0 105 IRQ_TYPE_NONE>; @@ -339,4 +346,73 @@ #interrupt-cells = <4>; }; }; + + smd { + compatible = "qcom,smd"; + + rpm { + interrupts = <0 168 1>; + qcom,ipc = <&apcs 8 0>; + qcom,smd-edge = <15>; + + rpm_requests { + compatible = "qcom,rpm-msm8974"; + qcom,smd-channels = "rpm_requests"; + + pm8841-regulators { + compatible = "qcom,rpm-pm8841-regulators"; + + pm8841_s1: s1 {}; + pm8841_s2: s2 {}; + pm8841_s3: s3 {}; + pm8841_s4: s4 {}; + pm8841_s5: s5 {}; + pm8841_s6: s6 {}; + pm8841_s7: s7 {}; + pm8841_s8: s8 {}; + }; + + pm8941-regulators { + compatible = "qcom,rpm-pm8941-regulators"; + + pm8941_s1: s1 {}; + pm8941_s2: s2 {}; + pm8941_s3: s3 {}; + pm8941_5v: s4 {}; + + pm8941_l1: l1 {}; + pm8941_l2: l2 {}; + pm8941_l3: l3 {}; + pm8941_l4: l4 {}; + pm8941_l5: l5 {}; + pm8941_l6: l6 {}; + pm8941_l7: l7 {}; + pm8941_l8: l8 {}; + pm8941_l9: l9 {}; + pm8941_l10: l10 {}; + pm8941_l11: l11 {}; + pm8941_l12: l12 {}; + pm8941_l13: l13 {}; + pm8941_l14: l14 {}; + pm8941_l15: l15 {}; + pm8941_l16: l16 {}; + pm8941_l17: l17 {}; + pm8941_l18: l18 {}; + pm8941_l19: l19 {}; + pm8941_l20: l20 {}; + pm8941_l21: l21 {}; + pm8941_l22: l22 {}; + pm8941_l23: l23 {}; + pm8941_l24: l24 {}; + + pm8941_lvs1: lvs1 {}; + pm8941_lvs2: lvs2 {}; + pm8941_lvs3: lvs3 {}; + + pm8941_5vs1: 5vs1 {}; + pm8941_5vs2: 5vs2 {}; + }; + }; + }; + }; }; diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi index 968f1043d4f5..b0d443999fcc 100644 --- a/arch/arm/boot/dts/qcom-pm8941.dtsi +++ b/arch/arm/boot/dts/qcom-pm8941.dtsi @@ -26,6 +26,27 @@ bias-pull-up; }; + charger@1000 { + compatible = "qcom,pm8941-charger"; + reg = <0x1000 0x700>; + interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>; + interrupt-names = "chg-done", + "chg-fast", + "chg-trkl", + "bat-temp-ok", + "bat-present", + "chg-gone", + "usb-valid", + "dc-valid"; + }; + pm8941_gpios: gpios@c000 { compatible = "qcom,pm8941-gpio"; reg = <0xc000 0x2400>; @@ -120,8 +141,7 @@ pm8941_iadc: iadc@3600 { compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc"; - reg = <0x3600 0x100>, - <0x12f1 0x1>; + reg = <0x3600 0x100>; interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>; qcom,external-resistor-micro-ohms = <10000>; }; diff --git a/arch/arm/boot/dts/r8a7778.dtsi b/arch/arm/boot/dts/r8a7778.dtsi index 4b1fa9f42ad5..4f8e07811746 100644 --- a/arch/arm/boot/dts/r8a7778.dtsi +++ b/arch/arm/boot/dts/r8a7778.dtsi @@ -239,7 +239,7 @@ #sound-dai-cells = <1>; compatible = "renesas,rcar_sound-r8a7778", "renesas,rcar_sound-gen1"; reg = <0xffd90000 0x1000>, /* SRU */ - <0xffd91000 0x1240>, /* SSI */ + <0xffd91000 0x240>, /* SSI */ <0xfffe0000 0x24>; /* ADG */ clocks = <&mstp3_clks R8A7778_CLK_SSI8>, <&mstp3_clks R8A7778_CLK_SSI7>, diff --git a/arch/arm/boot/dts/r8a7779-marzen.dts b/arch/arm/boot/dts/r8a7779-marzen.dts index 20afea6f06ef..fe396c8d58db 100644 --- a/arch/arm/boot/dts/r8a7779-marzen.dts +++ b/arch/arm/boot/dts/r8a7779-marzen.dts @@ -19,12 +19,12 @@ compatible = "renesas,marzen", "renesas,r8a7779"; aliases { - serial2 = &scif2; - serial4 = &scif4; + serial0 = &scif2; + serial1 = &scif4; }; chosen { - bootargs = "console=ttySC2,115200 ignore_loglevel root=/dev/nfs ip=on"; + bootargs = "ignore_loglevel root=/dev/nfs ip=on"; stdout-path = &scif2; }; diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts index 37dec5269491..c553abd711ee 100644 --- a/arch/arm/boot/dts/r8a7790-lager.dts +++ b/arch/arm/boot/dts/r8a7790-lager.dts @@ -174,6 +174,13 @@ 1800000 0>; }; + audio_clock: clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <11289600>; + clock-output-names = "audio_clock"; + }; + rsnd_ak4643: sound { compatible = "simple-audio-card"; @@ -187,7 +194,7 @@ sndcodec: simple-audio-card,codec { sound-dai = <&ak4643>; - system-clock-frequency = <11289600>; + clocks = <&audio_clock>; }; }; @@ -335,6 +342,11 @@ renesas,function = "msiof1"; }; + iic0_pins: iic0 { + renesas,groups = "iic0"; + renesas,function = "iic0"; + }; + iic1_pins: iic1 { renesas,groups = "iic1"; renesas,function = "iic1"; @@ -510,6 +522,8 @@ &iic0 { status = "okay"; + pinctrl-0 = <&iic0_pins>; + pinctrl-names = "default"; }; &iic1 { diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi index 4624d0f2a754..e07ae5d45e19 100644 --- a/arch/arm/boot/dts/r8a7790.dtsi +++ b/arch/arm/boot/dts/r8a7790.dtsi @@ -1599,7 +1599,7 @@ reg = <0 0xec500000 0 0x1000>, /* SCU */ <0 0xec5a0000 0 0x100>, /* ADG */ <0 0xec540000 0 0x1000>, /* SSIU */ - <0 0xec541000 0 0x1280>, /* SSI */ + <0 0xec541000 0 0x280>, /* SSI */ <0 0xec740000 0 0x200>; /* Audio DMAC peri peri*/ reg-names = "scu", "adg", "ssiu", "ssi", "audmapp"; diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts index dc158845afdc..fc44ea361a4b 100644 --- a/arch/arm/boot/dts/r8a7791-koelsch.dts +++ b/arch/arm/boot/dts/r8a7791-koelsch.dts @@ -242,6 +242,13 @@ 1800000 0>; }; + audio_clock: clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <11289600>; + clock-output-names = "audio_clock"; + }; + rsnd_ak4643: sound { compatible = "simple-audio-card"; @@ -255,7 +262,7 @@ sndcodec: simple-audio-card,codec { sound-dai = <&ak4643>; - system-clock-frequency = <11289600>; + clocks = <&audio_clock>; }; }; diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts new file mode 100644 index 000000000000..fe0f12fc02a1 --- /dev/null +++ b/arch/arm/boot/dts/r8a7791-porter.dts @@ -0,0 +1,282 @@ +/* + * Device Tree Source for the Porter board + * + * Copyright (C) 2015 Cogent Embedded, Inc. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +/dts-v1/; +#include "r8a7791.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Porter"; + compatible = "renesas,porter", "renesas,r8a7791"; + + aliases { + serial0 = &scif0; + }; + + chosen { + bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp"; + stdout-path = &scif0; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0 0x40000000 0 0x40000000>; + }; + + memory@200000000 { + device_type = "memory"; + reg = <2 0x00000000 0 0x40000000>; + }; + + vcc_sdhi0: regulator@0 { + compatible = "regulator-fixed"; + + regulator-name = "SDHI0 Vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vccq_sdhi0: regulator@1 { + compatible = "regulator-gpio"; + + regulator-name = "SDHI0 VccQ"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpio2 12 GPIO_ACTIVE_HIGH>; + gpios-states = <1>; + states = <3300000 1 + 1800000 0>; + }; + + vcc_sdhi2: regulator@2 { + compatible = "regulator-fixed"; + + regulator-name = "SDHI2 Vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vccq_sdhi2: regulator@3 { + compatible = "regulator-gpio"; + + regulator-name = "SDHI2 VccQ"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>; + gpios-states = <1>; + states = <3300000 1 + 1800000 0>; + }; +}; + +&extal_clk { + clock-frequency = <20000000>; +}; + +&pfc { + scif0_pins: serial0 { + renesas,groups = "scif0_data_d"; + renesas,function = "scif0"; + }; + + ether_pins: ether { + renesas,groups = "eth_link", "eth_mdio", "eth_rmii"; + renesas,function = "eth"; + }; + + phy1_pins: phy1 { + renesas,groups = "intc_irq0"; + renesas,function = "intc"; + }; + + sdhi0_pins: sd0 { + renesas,groups = "sdhi0_data4", "sdhi0_ctrl"; + renesas,function = "sdhi0"; + }; + + sdhi2_pins: sd2 { + renesas,groups = "sdhi2_data4", "sdhi2_ctrl"; + renesas,function = "sdhi2"; + }; + + qspi_pins: spi0 { + renesas,groups = "qspi_ctrl", "qspi_data4"; + renesas,function = "qspi"; + }; + + i2c2_pins: i2c2 { + renesas,groups = "i2c2"; + renesas,function = "i2c2"; + }; + + usb0_pins: usb0 { + renesas,groups = "usb0"; + renesas,function = "usb0"; + }; + + usb1_pins: usb1 { + renesas,groups = "usb1"; + renesas,function = "usb1"; + }; + + vin0_pins: vin0 { + renesas,groups = "vin0_data8", "vin0_clk"; + renesas,function = "vin0"; + }; +}; + +&scif0 { + pinctrl-0 = <&scif0_pins>; + pinctrl-names = "default"; + + status = "okay"; +}; + +ðer { + pinctrl-0 = <ðer_pins &phy1_pins>; + pinctrl-names = "default"; + + phy-handle = <&phy1>; + renesas,ether-link-active-low; + status = "ok"; + + phy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&irqc0>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + micrel,led-mode = <1>; + }; +}; + +&sdhi0 { + pinctrl-0 = <&sdhi0_pins>; + pinctrl-names = "default"; + + vmmc-supply = <&vcc_sdhi0>; + vqmmc-supply = <&vccq_sdhi0>; + cd-gpios = <&gpio6 6 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&sdhi2 { + pinctrl-0 = <&sdhi2_pins>; + pinctrl-names = "default"; + + vmmc-supply = <&vcc_sdhi2>; + vqmmc-supply = <&vccq_sdhi2>; + cd-gpios = <&gpio6 22 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&qspi { + pinctrl-0 = <&qspi_pins>; + pinctrl-names = "default"; + + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,s25fl512s", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <30000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + m25p,fast-read; + + partition@0 { + label = "loader_prg"; + reg = <0x00000000 0x00040000>; + read-only; + }; + partition@40000 { + label = "user_prg"; + reg = <0x00040000 0x00400000>; + read-only; + }; + partition@440000 { + label = "flash_fs"; + reg = <0x00440000 0x03bc0000>; + }; + }; +}; + +&i2c2 { + pinctrl-0 = <&i2c2_pins>; + pinctrl-names = "default"; + + status = "okay"; + clock-frequency = <400000>; + + composite-in@20 { + compatible = "adi,adv7180"; + reg = <0x20>; + remote = <&vin0>; + + port { + adv7180: endpoint { + bus-width = <8>; + remote-endpoint = <&vin0ep>; + }; + }; + }; +}; + +&sata0 { + status = "okay"; +}; + +/* composite video input */ +&vin0 { + status = "ok"; + pinctrl-0 = <&vin0_pins>; + pinctrl-names = "default"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + vin0ep: endpoint { + remote-endpoint = <&adv7180>; + bus-width = <8>; + }; + }; +}; + +&pci0 { + pinctrl-0 = <&usb0_pins>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pci1 { + pinctrl-0 = <&usb1_pins>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; + +&pcie_bus_clk { + status = "okay"; +}; + +&pciec { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi index 1666c8a6b143..328f48bd15e7 100644 --- a/arch/arm/boot/dts/r8a7791.dtsi +++ b/arch/arm/boot/dts/r8a7791.dtsi @@ -1649,7 +1649,7 @@ reg = <0 0xec500000 0 0x1000>, /* SCU */ <0 0xec5a0000 0 0x100>, /* ADG */ <0 0xec540000 0 0x1000>, /* SSIU */ - <0 0xec541000 0 0x1280>, /* SSI */ + <0 0xec541000 0 0x280>, /* SSI */ <0 0xec740000 0 0x200>; /* Audio DMAC peri peri*/ reg-names = "scu", "adg", "ssiu", "ssi", "audmapp"; diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts index d4dd5a30ccdf..48ff3e2958ae 100644 --- a/arch/arm/boot/dts/r8a7794-silk.dts +++ b/arch/arm/boot/dts/r8a7794-silk.dts @@ -61,10 +61,35 @@ renesas,function = "intc"; }; + i2c1_pins: i2c1 { + renesas,groups = "i2c1"; + renesas,function = "i2c1"; + }; + mmcif0_pins: mmcif0 { renesas,groups = "mmc_data8", "mmc_ctrl"; renesas,function = "mmc"; }; + + qspi_pins: spi0 { + renesas,groups = "qspi_ctrl", "qspi_data4"; + renesas,function = "qspi"; + }; + + vin0_pins: vin0 { + renesas,groups = "vin0_data8", "vin0_clk"; + renesas,function = "vin0"; + }; + + usb0_pins: usb0 { + renesas,groups = "usb0"; + renesas,function = "usb0"; + }; + + usb1_pins: usb1 { + renesas,groups = "usb1"; + renesas,function = "usb1"; + }; }; &scif2 { @@ -90,6 +115,27 @@ }; }; +&i2c1 { + pinctrl-0 = <&i2c1_pins>; + pinctrl-names = "default"; + + status = "okay"; + clock-frequency = <400000>; + + composite-in@20 { + compatible = "adi,adv7180"; + reg = <0x20>; + remote = <&vin0>; + + port { + adv7180: endpoint { + bus-width = <8>; + remote-endpoint = <&vin0ep>; + }; + }; + }; +}; + &mmcif0 { pinctrl-0 = <&mmcif0_pins>; pinctrl-names = "default"; @@ -100,3 +146,71 @@ non-removable; status = "okay"; }; + +&qspi { + pinctrl-0 = <&qspi_pins>; + pinctrl-names = "default"; + + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,s25fl512s", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <30000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + spi-cpol; + spi-cpha; + m25p,fast-read; + + partition@0 { + label = "loader"; + reg = <0x00000000 0x00040000>; + read-only; + }; + partition@40000 { + label = "user"; + reg = <0x00040000 0x00400000>; + read-only; + }; + partition@440000 { + label = "flash"; + reg = <0x00440000 0x03bc0000>; + }; + }; +}; + +/* composite video input */ +&vin0 { + status = "okay"; + pinctrl-0 = <&vin0_pins>; + pinctrl-names = "default"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + vin0ep: endpoint { + remote-endpoint = <&adv7180>; + bus-width = <8>; + }; + }; +}; + +&pci0 { + status = "okay"; + pinctrl-0 = <&usb0_pins>; + pinctrl-names = "default"; +}; + +&pci1 { + status = "okay"; + pinctrl-0 = <&usb1_pins>; + pinctrl-names = "default"; +}; + +&usbphy { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi index 97c8e9ace5eb..a9977d6ee81a 100644 --- a/arch/arm/boot/dts/r8a7794.dtsi +++ b/arch/arm/boot/dts/r8a7794.dtsi @@ -19,6 +19,18 @@ #address-cells = <2>; #size-cells = <2>; + aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + i2c3 = &i2c3; + i2c4 = &i2c4; + i2c5 = &i2c5; + spi0 = &qspi; + vin0 = &vin0; + vin1 = &vin1; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -50,6 +62,97 @@ interrupts = <1 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>; }; + gpio0: gpio@e6050000 { + compatible = "renesas,gpio-r8a7794", "renesas,gpio-rcar"; + reg = <0 0xe6050000 0 0x50>; + interrupts = <0 4 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 0 32>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&mstp9_clks R8A7794_CLK_GPIO0>; + power-domains = <&cpg_clocks>; + }; + + gpio1: gpio@e6051000 { + compatible = "renesas,gpio-r8a7794", "renesas,gpio-rcar"; + reg = <0 0xe6051000 0 0x50>; + interrupts = <0 5 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 32 26>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&mstp9_clks R8A7794_CLK_GPIO1>; + power-domains = <&cpg_clocks>; + }; + + gpio2: gpio@e6052000 { + compatible = "renesas,gpio-r8a7794", "renesas,gpio-rcar"; + reg = <0 0xe6052000 0 0x50>; + interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 64 32>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&mstp9_clks R8A7794_CLK_GPIO2>; + power-domains = <&cpg_clocks>; + }; + + gpio3: gpio@e6053000 { + compatible = "renesas,gpio-r8a7794", "renesas,gpio-rcar"; + reg = <0 0xe6053000 0 0x50>; + interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 96 32>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&mstp9_clks R8A7794_CLK_GPIO3>; + power-domains = <&cpg_clocks>; + }; + + gpio4: gpio@e6054000 { + compatible = "renesas,gpio-r8a7794", "renesas,gpio-rcar"; + reg = <0 0xe6054000 0 0x50>; + interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 128 32>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&mstp9_clks R8A7794_CLK_GPIO4>; + power-domains = <&cpg_clocks>; + }; + + gpio5: gpio@e6055000 { + compatible = "renesas,gpio-r8a7794", "renesas,gpio-rcar"; + reg = <0 0xe6055000 0 0x50>; + interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 160 28>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&mstp9_clks R8A7794_CLK_GPIO5>; + power-domains = <&cpg_clocks>; + }; + + gpio6: gpio@e6055400 { + compatible = "renesas,gpio-r8a7794", "renesas,gpio-rcar"; + reg = <0 0xe6055400 0 0x50>; + interrupts = <0 10 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 192 26>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&mstp9_clks R8A7794_CLK_GPIO6>; + power-domains = <&cpg_clocks>; + }; + cmt0: timer@ffca0000 { compatible = "renesas,cmt-48-gen2"; reg = <0 0xffca0000 0 0x1004>; @@ -407,6 +510,73 @@ status = "disabled"; }; + /* The memory map in the User's Manual maps the cores to bus numbers */ + i2c0: i2c@e6508000 { + compatible = "renesas,i2c-r8a7794"; + reg = <0 0xe6508000 0 0x40>; + interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7794_CLK_I2C0>; + power-domains = <&cpg_clocks>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c1: i2c@e6518000 { + compatible = "renesas,i2c-r8a7794"; + reg = <0 0xe6518000 0 0x40>; + interrupts = <0 288 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7794_CLK_I2C1>; + power-domains = <&cpg_clocks>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@e6530000 { + compatible = "renesas,i2c-r8a7794"; + reg = <0 0xe6530000 0 0x40>; + interrupts = <0 286 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7794_CLK_I2C2>; + power-domains = <&cpg_clocks>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c3: i2c@e6540000 { + compatible = "renesas,i2c-r8a7794"; + reg = <0 0xe6540000 0 0x40>; + interrupts = <0 290 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7794_CLK_I2C3>; + power-domains = <&cpg_clocks>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c4: i2c@e6520000 { + compatible = "renesas,i2c-r8a7794"; + reg = <0 0xe6520000 0 0x40>; + interrupts = <0 19 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7794_CLK_I2C4>; + power-domains = <&cpg_clocks>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c5: i2c@e6528000 { + compatible = "renesas,i2c-r8a7794"; + reg = <0 0xe6528000 0 0x40>; + interrupts = <0 20 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7794_CLK_I2C5>; + power-domains = <&cpg_clocks>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + mmcif0: mmc@ee200000 { compatible = "renesas,mmcif-r8a7794", "renesas,sh-mmcif"; reg = <0 0xee200000 0 0x80>; @@ -446,6 +616,140 @@ status = "disabled"; }; + qspi: spi@e6b10000 { + compatible = "renesas,qspi-r8a7794", "renesas,qspi"; + reg = <0 0xe6b10000 0 0x2c>; + interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7794_CLK_QSPI_MOD>; + dmas = <&dmac0 0x17>, <&dmac0 0x18>; + dma-names = "tx", "rx"; + power-domains = <&cpg_clocks>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + vin0: video@e6ef0000 { + compatible = "renesas,vin-r8a7794"; + reg = <0 0xe6ef0000 0 0x1000>; + interrupts = <0 188 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R8A7794_CLK_VIN0>; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + vin1: video@e6ef1000 { + compatible = "renesas,vin-r8a7794"; + reg = <0 0xe6ef1000 0 0x1000>; + interrupts = <0 189 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R8A7794_CLK_VIN1>; + power-domains = <&cpg_clocks>; + status = "disabled"; + }; + + pci0: pci@ee090000 { + compatible = "renesas,pci-r8a7794"; + device_type = "pci"; + reg = <0 0xee090000 0 0xc00>, + <0 0xee080000 0 0x1100>; + interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7794_CLK_EHCI>; + power-domains = <&cpg_clocks>; + status = "disabled"; + + bus-range = <0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x02000000 0 0xee080000 0 0xee080000 0 0x00010000>; + interrupt-map-mask = <0xff00 0 0 0x7>; + interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH + 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH + 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>; + + usb@0,1 { + reg = <0x800 0 0 0 0>; + device_type = "pci"; + phys = <&usb0 0>; + phy-names = "usb"; + }; + + usb@0,2 { + reg = <0x1000 0 0 0 0>; + device_type = "pci"; + phys = <&usb0 0>; + phy-names = "usb"; + }; + }; + + pci1: pci@ee0d0000 { + compatible = "renesas,pci-r8a7794"; + device_type = "pci"; + reg = <0 0xee0d0000 0 0xc00>, + <0 0xee0c0000 0 0x1100>; + interrupts = <0 113 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7794_CLK_EHCI>; + power-domains = <&cpg_clocks>; + status = "disabled"; + + bus-range = <1 1>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x02000000 0 0xee0c0000 0 0xee0c0000 0 0x00010000>; + interrupt-map-mask = <0xff00 0 0 0x7>; + interrupt-map = <0x0000 0 0 1 &gic 0 113 IRQ_TYPE_LEVEL_HIGH + 0x0800 0 0 1 &gic 0 113 IRQ_TYPE_LEVEL_HIGH + 0x1000 0 0 2 &gic 0 113 IRQ_TYPE_LEVEL_HIGH>; + + usb@0,1 { + reg = <0x800 0 0 0 0>; + device_type = "pci"; + phys = <&usb2 0>; + phy-names = "usb"; + }; + + usb@0,2 { + reg = <0x1000 0 0 0 0>; + device_type = "pci"; + phys = <&usb2 0>; + phy-names = "usb"; + }; + }; + + hsusb: usb@e6590000 { + compatible = "renesas,usbhs-r8a7794"; + reg = <0 0xe6590000 0 0x100>; + interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7794_CLK_HSUSB>; + power-domains = <&cpg_clocks>; + renesas,buswait = <4>; + phys = <&usb0 1>; + phy-names = "usb"; + status = "disabled"; + }; + + usbphy: usb-phy@e6590100 { + compatible = "renesas,usb-phy-r8a7794"; + reg = <0 0xe6590100 0 0x100>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&mstp7_clks R8A7794_CLK_HSUSB>; + clock-names = "usbhs"; + power-domains = <&cpg_clocks>; + status = "disabled"; + + usb0: usb-channel@0 { + reg = <0>; + #phy-cells = <1>; + }; + usb2: usb-channel@2 { + reg = <2>; + #phy-cells = <1>; + }; + }; + clocks { #address-cells = <2>; #size-cells = <2>; @@ -749,16 +1053,22 @@ mstp9_clks: mstp9_clks@e6150994 { compatible = "renesas,r8a7794-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe6150994 0 4>, <0 0xe61509a4 0 4>; - clocks = <&cpg_clocks R8A7794_CLK_QSPI>, <&hp_clk>, <&hp_clk>, - <&hp_clk>, <&hp_clk>, <&hp_clk>, <&hp_clk>; + clocks = <&cp_clk>, <&cp_clk>, <&cp_clk>, <&cp_clk>, + <&cp_clk>, <&cp_clk>, <&cp_clk>, + <&cpg_clocks R8A7794_CLK_QSPI>, <&hp_clk>, <&hp_clk>, + <&hp_clk>, <&hp_clk>, <&hp_clk>, <&hp_clk>; #clock-cells = <1>; - clock-indices = < - R8A7794_CLK_QSPI_MOD R8A7794_CLK_I2C5 R8A7794_CLK_I2C4 - R8A7794_CLK_I2C3 R8A7794_CLK_I2C2 R8A7794_CLK_I2C1 - R8A7794_CLK_I2C0 - >; + clock-indices = <R8A7794_CLK_GPIO6 R8A7794_CLK_GPIO5 + R8A7794_CLK_GPIO4 R8A7794_CLK_GPIO3 + R8A7794_CLK_GPIO2 R8A7794_CLK_GPIO1 + R8A7794_CLK_GPIO0 R8A7794_CLK_QSPI_MOD + R8A7794_CLK_I2C5 R8A7794_CLK_I2C4 + R8A7794_CLK_I2C3 R8A7794_CLK_I2C2 + R8A7794_CLK_I2C1 R8A7794_CLK_I2C0>; clock-output-names = - "qspi_mod", "i2c5", "i2c4", "i2c3", "i2c2", "i2c1", "i2c0"; + "gpio6", "gpio5", "gpio4", "gpio3", "gpio2", + "gpio1", "gpio0", "qspi_mod", + "i2c5", "i2c4", "i2c3", "i2c2", "i2c1", "i2c0"; }; mstp11_clks: mstp11_clks@e615099c { compatible = "renesas,r8a7794-mstp-clocks", "renesas,cpg-mstp-clocks"; diff --git a/arch/arm/boot/dts/r8a77xx-aa121td01-panel.dtsi b/arch/arm/boot/dts/r8a77xx-aa121td01-panel.dtsi new file mode 100644 index 000000000000..a07ebf8f6938 --- /dev/null +++ b/arch/arm/boot/dts/r8a77xx-aa121td01-panel.dtsi @@ -0,0 +1,41 @@ +/* + * Common file for the AA121TD01 panel connected to Renesas R-Car boards + * + * Copyright (C) 2015 Renesas Electronics Corp. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +/ { + panel { + compatible = "mitsubishi,aa121td01", "panel-dpi"; + + width-mm = <261>; + height-mm = <163>; + + panel-timing { + /* 1280x800 @60Hz */ + clock-frequency = <71000000>; + hactive = <1280>; + vactive = <800>; + hsync-len = <70>; + hfront-porch = <20>; + hback-porch = <70>; + vsync-len = <5>; + vfront-porch = <3>; + vback-porch = <15>; + }; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds_connector>; + }; + }; + }; +}; + +&lvds_connector { + remote-endpoint = <&panel_in>; +}; diff --git a/arch/arm/boot/dts/rk3066a-bqcurie2.dts b/arch/arm/boot/dts/rk3066a-bqcurie2.dts index c0273755431a..38c91a839795 100644 --- a/arch/arm/boot/dts/rk3066a-bqcurie2.dts +++ b/arch/arm/boot/dts/rk3066a-bqcurie2.dts @@ -186,6 +186,8 @@ pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_cd>, <&sd0_bus4>; vmmc-supply = <&vcc_sd0>; bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; disable-wp; }; diff --git a/arch/arm/boot/dts/rk3066a-marsboard.dts b/arch/arm/boot/dts/rk3066a-marsboard.dts index bae965c123c1..7cdc308bfac5 100644 --- a/arch/arm/boot/dts/rk3066a-marsboard.dts +++ b/arch/arm/boot/dts/rk3066a-marsboard.dts @@ -178,6 +178,14 @@ }; }; +&mmc0 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_cd>, <&sd0_bus4>; + vmmc-supply = <&vcc_sd0>; +}; + &pinctrl { lan8720a { phy_int: phy-int { diff --git a/arch/arm/boot/dts/rk3066a-rayeager.dts b/arch/arm/boot/dts/rk3066a-rayeager.dts index e36383c701dc..341c1f87936a 100644 --- a/arch/arm/boot/dts/rk3066a-rayeager.dts +++ b/arch/arm/boot/dts/rk3066a-rayeager.dts @@ -330,6 +330,8 @@ pinctrl-names = "default"; pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_cd>, <&sd0_bus4>; vmmc-supply = <&vcc_sd>; + cap-mmc-highspeed; + cap-sd-highspeed; status = "okay"; }; diff --git a/arch/arm/boot/dts/rk3188-radxarock.dts b/arch/arm/boot/dts/rk3188-radxarock.dts index d2180e5d2b05..66fa87d1e2c2 100644 --- a/arch/arm/boot/dts/rk3188-radxarock.dts +++ b/arch/arm/boot/dts/rk3188-radxarock.dts @@ -90,6 +90,21 @@ }; }; + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "SPDIF"; + + simple-audio-card,dai-link@1 { /* S/PDIF - S/PDIF */ + cpu { sound-dai = <&spdif>; }; + codec { sound-dai = <&spdif_out>; }; + }; + }; + + spdif_out: spdif-out { + compatible = "linux,spdif-dit"; + #sound-dai-cells = <0>; + }; + ir_recv: gpio-ir-receiver { compatible = "gpio-ir-receiver"; gpios = <&gpio0 10 1>; @@ -289,6 +304,8 @@ vmmc-supply = <&vcc_sd0>; bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; disable-wp; }; @@ -343,6 +360,10 @@ }; }; +&spdif { + status = "okay"; +}; + &uart0 { status = "okay"; }; diff --git a/arch/arm/boot/dts/rk3188.dtsi b/arch/arm/boot/dts/rk3188.dtsi index 316304272118..6399942f1840 100644 --- a/arch/arm/boot/dts/rk3188.dtsi +++ b/arch/arm/boot/dts/rk3188.dtsi @@ -121,6 +121,20 @@ status = "disabled"; }; + spdif: sound@1011e000 { + compatible = "rockchip,rk3188-spdif", "rockchip,rk3066-spdif"; + reg = <0x1011e000 0x2000>; + #sound-dai-cells = <0>; + clock-names = "hclk", "mclk"; + clocks = <&cru HCLK_SPDIF>, <&cru SCLK_SPDIF>; + dmas = <&dmac1_s 8>; + dma-names = "tx"; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&spdif_tx>; + status = "disabled"; + }; + cru: clock-controller@20000000 { compatible = "rockchip,rk3188-cru"; reg = <0x20000000 0x1000>; @@ -484,6 +498,12 @@ <RK_GPIO1 21 RK_FUNC_1 &pcfg_pull_none>; }; }; + + spdif { + spdif_tx: spdif-tx { + rockchip,pins = <RK_GPIO1 14 RK_FUNC_1 &pcfg_pull_none>; + }; + }; }; }; diff --git a/arch/arm/boot/dts/rk3288-firefly.dtsi b/arch/arm/boot/dts/rk3288-firefly.dtsi index 20fa0ef0b96b..4e3fd9aefe34 100644 --- a/arch/arm/boot/dts/rk3288-firefly.dtsi +++ b/arch/arm/boot/dts/rk3288-firefly.dtsi @@ -48,6 +48,14 @@ reg = <0 0x80000000>; }; + dovdd_1v8: dovdd-1v8-regulator { + compatible = "regulator-fixed"; + regulator-name = "dovdd_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc28_dvp>; + }; + ext_gmac: external-gmac-clock { compatible = "fixed-clock"; #clock-cells = <0>; @@ -55,6 +63,22 @@ clock-output-names = "ext_gmac"; }; + io_domains: io-domains { + compatible = "rockchip,rk3288-io-voltage-domain"; + rockchip,grf = <&grf>; + + audio-supply = <&vcca_33>; + bb-supply = <&vcc_io>; + dvp-supply = <&dovdd_1v8>; + flash0-supply = <&vcc_flash>; + flash1-supply = <&vcc_lan>; + gpio30-supply = <&vcc_io>; + gpio1830-supply = <&vcc_io>; + lcdc-supply = <&vcc_io>; + sdcard-supply = <&vccio_sd>; + wifi-supply = <&vccio_wl>; + }; + ir: ir-receiver { compatible = "gpio-ir-receiver"; pinctrl-names = "default"; @@ -96,7 +120,7 @@ }; }; - vcc_sys: vsys-regulator { + vbat_wl: vcc_sys: vsys-regulator { compatible = "regulator-fixed"; regulator-name = "vcc_sys"; regulator-min-microvolt = <5000000>; @@ -160,6 +184,23 @@ regulator-always-on; vin-supply = <&vcc_5v>; }; + + /* + * A TT8142 creates both dovdd_1v8 and vcc28_dvp, controlled + * by the dvp_pwr pin. + */ + vcc28_dvp: vcc28-dvp-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 11 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&dvp_pwr>; + regulator-name = "vcc28_dvp"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + vin-supply = <&vcc_io>; + }; }; &cpu0 { @@ -325,7 +366,7 @@ regulator-always-on; }; - vcc_18: REG11 { + vccio_wl: vcc_18: REG11 { regulator-name = "vcc_18"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -373,6 +414,12 @@ }; }; + dvp { + dvp_pwr: dvp-pwr { + rockchip,pins = <0 11 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + gmac { phy_int: phy-int { rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_pull_up>; @@ -445,7 +492,8 @@ num-slots = <1>; pinctrl-names = "default"; pinctrl-0 = <&sdio0_bus4>, <&sdio0_cmd>, <&sdio0_clk>; - vmmc-supply = <&vcc_18>; + vmmc-supply = <&vbat_wl>; + vqmmc-supply = <&vccio_wl>; status = "okay"; }; @@ -459,6 +507,7 @@ pinctrl-names = "default"; pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>; vmmc-supply = <&vcc_sd>; + vqmmc-supply = <&vccio_sd>; status = "okay"; }; diff --git a/arch/arm/boot/dts/rk3288-popmetal.dts b/arch/arm/boot/dts/rk3288-popmetal.dts index f82b956ebf17..65c475642d5a 100644 --- a/arch/arm/boot/dts/rk3288-popmetal.dts +++ b/arch/arm/boot/dts/rk3288-popmetal.dts @@ -79,6 +79,22 @@ }; }; + io_domains: io-domains { + compatible = "rockchip,rk3288-io-voltage-domain"; + rockchip,grf = <&grf>; + + audio-supply = <&vcca_33>; + bb-supply = <&vcc_io>; + dvp-supply = <&vcc18_dvp>; + flash0-supply = <&vcc_flash>; + flash1-supply = <&vcc_lan>; + gpio30-supply = <&vcc_io>; + gpio1830-supply = <&vcc_io>; + lcdc-supply = <&vcc_io>; + sdcard-supply = <&vccio_sd>; + wifi-supply = <&vccio_wl>; + }; + ir: ir-receiver { compatible = "gpio-ir-receiver"; gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; @@ -86,6 +102,26 @@ pinctrl-0 = <&ir_int>; }; + vcc_flash: flash-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_flash"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_io>; + }; + + vcc_sd: sdmmc-regulator { + compatible = "regulator-fixed"; + gpio = <&gpio7 11 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_pwr>; + regulator-name = "vcc_sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <100000>; + vin-supply = <&vcc_io>; + }; + vcc_sys: vsys-regulator { compatible = "regulator-fixed"; regulator-name = "vcc_sys"; @@ -94,6 +130,31 @@ regulator-always-on; regulator-boot-on; }; + + /* + * A PT5128 creates both dovdd_1v8 and vcc28_dvp, controlled + * by the dvp_pwr pin. + */ + vcc18_dvp: vcc18-dvp-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc18-dvp"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc28_dvp>; + }; + + vcc28_dvp: vcc28-dvp-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 17 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&dvp_pwr>; + regulator-name = "vcc28_dvp"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + vin-supply = <&vcc_io>; + }; }; &cpu0 { @@ -109,6 +170,8 @@ num-slots = <1>; pinctrl-names = "default"; pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>; + vmmc-supply = <&vcc_io>; + vqmmc-supply = <&vcc_flash>; status = "okay"; }; @@ -121,6 +184,8 @@ num-slots = <1>; pinctrl-names = "default"; pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>; + vmmc-supply = <&vcc_sd>; + vqmmc-supply = <&vccio_sd>; status = "okay"; }; @@ -297,22 +362,22 @@ }; }; - vcca_codec: LDO_REG8 { + vcca_33: LDO_REG8 { regulator-always-on; regulator-boot-on; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - regulator-name = "vcca_codec"; + regulator-name = "vcca_33"; regulator-state-mem { regulator-on-in-suspend; regulator-suspend-microvolt = <3300000>; }; }; - vcc_wl: SWITCH_REG1 { + vccio_wl: SWITCH_REG1 { regulator-always-on; regulator-boot-on; - regulator-name = "vcc_wl"; + regulator-name = "vccio_wl"; regulator-state-mem { regulator-on-in-suspend; }; @@ -388,6 +453,12 @@ }; }; + dvp { + dvp_pwr: dvp-pwr { + rockchip,pins = <0 17 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + ir { ir_int: ir-int { rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_up>; @@ -405,6 +476,12 @@ rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>; }; }; + + sdmmc { + sdmmc_pwr: sdmmc-pwr { + rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; }; &tsadc { diff --git a/arch/arm/boot/dts/rk3288-rock2-som.dtsi b/arch/arm/boot/dts/rk3288-rock2-som.dtsi new file mode 100644 index 000000000000..1813b7c36556 --- /dev/null +++ b/arch/arm/boot/dts/rk3288-rock2-som.dtsi @@ -0,0 +1,277 @@ +/* + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/pwm/pwm.h> +#include "rk3288.dtsi" + +/ { + memory { + reg = <0x0 0x80000000>; + device_type = "memory"; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + pinctrl-0 = <&emmc_reset>; + pinctrl-names = "default"; + reset-gpios = <&gpio3 9 GPIO_ACTIVE_LOW>; + }; + + ext_gmac: external-gmac-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <125000000>; + clock-output-names = "ext_gmac"; + }; + + vcc_sys: vsys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_sys"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; +}; + +&cpu0 { + cpu0-supply = <&vdd_cpu>; +}; + +&emmc { + bus-width = <8>; + cap-mmc-highspeed; + disable-wp; + non-removable; + num-slots = <1>; + mmc-pwrseq = <&emmc_pwrseq>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>; + vmmc-supply = <&vcc_io>; + status = "okay"; +}; + +&gmac { + assigned-clocks = <&cru SCLK_MAC>; + assigned-clock-parents = <&ext_gmac>; + clock_in_out = "input"; + phy-mode = "rgmii"; + phy-supply = <&vccio_pmu>; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins &phy_rst>; + snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 30000>; + rx_delay = <0x10>; + tx_delay = <0x30>; +}; + +&i2c0 { + status = "okay"; + + act8846: act8846@5a { + compatible = "active-semi,act8846"; + reg = <0x5a>; + inl1-supply = <&vcc_io>; + inl2-supply = <&vcc_sys>; + inl3-supply = <&vcc_20>; + vp1-supply = <&vcc_sys>; + vp2-supply = <&vcc_sys>; + vp3-supply = <&vcc_sys>; + vp4-supply = <&vcc_sys>; + + regulators { + vcc_ddr: REG1 { + regulator-name = "VCC_DDR"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + vcc_io: REG2 { + regulator-name = "VCC_IO"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_log: REG3 { + regulator-name = "VDD_LOG"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + vcc_20: REG4 { + regulator-name = "VCC_20"; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + }; + + vccio_sd: REG5 { + regulator-name = "VCCIO_SD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd10_lcd: REG6 { + regulator-name = "VDD10_LCD"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + vcca_codec: REG7 { + regulator-name = "VCCA_CODEC"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vcca_tp: REG8 { + regulator-name = "VCCA_TP"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vccio_pmu: REG9 { + regulator-name = "VCCIO_PMU"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_10: REG10 { + regulator-name = "VDD_10"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + vcc_18: REG11 { + regulator-name = "VCC_18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + vcc18_lcd: REG12 { + regulator-name = "VCC18_LCD"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + }; + }; + + vdd_cpu: syr827@40 { + compatible = "silergy,syr827"; + reg = <0x40>; + fcs,suspend-voltage-selector = <1>; + regulator-always-on; + regulator-boot-on; + regulator-enable-ramp-delay = <300>; + regulator-name = "vdd_cpu"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <8000>; + vin-supply = <&vcc_sys>; + }; + + vdd_gpu: syr828@41 { + compatible = "silergy,syr828"; + reg = <0x41>; + fcs,suspend-voltage-selector = <1>; + regulator-always-on; + regulator-enable-ramp-delay = <300>; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1350000>; + regulator-name = "vdd_gpu"; + regulator-ramp-delay = <8000>; + vin-supply = <&vcc_sys>; + }; +}; + +&pinctrl { + pcfg_output_high: pcfg-output-high { + output-high; + }; + + emmc { + emmc_reset: emmc-reset { + rockchip,pins = <3 9 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + gmac { + phy_rst: phy-rst { + rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>; + }; + }; +}; + +&tsadc { + rockchip,hw-tshut-mode = <0>; /* tshut mode 0:CRU 1:GPIO */ + rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */ + status = "okay"; +}; + +&vopb { + status = "okay"; +}; + +&vopb_mmu { + status = "okay"; +}; + +&vopl { + status = "okay"; +}; + +&vopl_mmu { + status = "okay"; +}; + +&wdt { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/rk3288-rock2-square.dts b/arch/arm/boot/dts/rk3288-rock2-square.dts new file mode 100644 index 000000000000..8af35c867a80 --- /dev/null +++ b/arch/arm/boot/dts/rk3288-rock2-square.dts @@ -0,0 +1,167 @@ +/* + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "rk3288-rock2-som.dtsi" + +/ { + model = "Radxa Rock 2 Square"; + compatible = "radxa,rock2-square", "rockchip,rk3288"; + + chosen { + stdout-path = "serial2:115200n8"; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "SPDIF"; + simple-audio-card,dai-link@1 { /* S/PDIF - S/PDIF */ + cpu { sound-dai = <&spdif>; }; + codec { sound-dai = <&spdif_out>; }; + }; + }; + + spdif_out: spdif-out { + compatible = "linux,spdif-dit"; + #sound-dai-cells = <0>; + }; + + vcc_usb_host: vcc-host-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&host_vbus_drv>; + /* Always on as the rockchip usb phy doesn't have a vbus-supply + * property + */ + regulator-always-on; + regulator-name = "vcc_host"; + }; + + vcc_sd: sdmmc-regulator { + compatible = "regulator-fixed"; + gpio = <&gpio7 11 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_pwr>; + regulator-name = "vcc_sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_io>; + }; +}; + +&sdmmc { + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + card-detect-delay = <200>; + disable-wp; /* wp not hooked up */ + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>; + vmmc-supply = <&vcc_sd>; + vqmmc-supply = <&vccio_sd>; + status = "okay"; +}; + +&gmac { + status = "ok"; +}; + +&hdmi { + ddc-i2c-bus = <&i2c5>; + status = "okay"; +}; + +&i2c0 { + hym8563@51 { + compatible = "haoyu,hym8563"; + reg = <0x51>; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "xin32k"; + interrupt-parent = <&gpio0>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int>; + + }; +}; + +&i2c5 { + status = "okay"; +}; + +&pinctrl { + pmic { + pmic_int: pmic-int { + rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + usb { + host_vbus_drv: host-vbus-drv { + rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + sdmmc { + sdmmc_pwr: sdmmc-pwr { + rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +&spdif { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; + +&usb_host0_ehci { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/rk3288-veyron-jaq.dts b/arch/arm/boot/dts/rk3288-veyron-jaq.dts new file mode 100644 index 000000000000..c2f52cfb4d06 --- /dev/null +++ b/arch/arm/boot/dts/rk3288-veyron-jaq.dts @@ -0,0 +1,176 @@ +/* + * Google Veyron Jaq Rev 1+ board device tree source + * + * Copyright 2015 Google, Inc + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "rk3288-veyron-chromebook.dtsi" +#include "cros-ec-sbs.dtsi" + +/ { + model = "Google Jaq"; + compatible = "google,veyron-jaq-rev5", "google,veyron-jaq-rev4", + "google,veyron-jaq-rev3", "google,veyron-jaq-rev2", + "google,veyron-jaq-rev1", "google,veyron-jaq", + "google,veyron", "rockchip,rk3288"; + + panel_regulator: panel-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio7 14 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_enable_h>; + regulator-name = "panel_regulator"; + vin-supply = <&vcc33_sys>; + }; + + vcc18_lcd: vcc18-lcd { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&avdd_1v8_disp_en>; + regulator-name = "vcc18_lcd"; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc18_wl>; + }; + + backlight_regulator: backlight-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio2 12 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&bl_pwr_en>; + regulator-name = "backlight_regulator"; + vin-supply = <&vcc33_sys>; + startup-delay-us = <15000>; + }; +}; + +&rk808 { + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int_l &dvs_1 &dvs_2>; + dvs-gpios = <&gpio7 12 GPIO_ACTIVE_HIGH>, + <&gpio7 15 GPIO_ACTIVE_HIGH>; + + regulators { + mic_vcc: LDO_REG2 { + regulator-name = "mic_vcc"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; +}; + +&sdmmc { + disable-wp; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_gpio + &sdmmc_bus4>; +}; + +&vcc_5v { + enable-active-high; + gpio = <&gpio7 21 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&drv_5v>; +}; + +&vcc50_hdmi { + enable-active-high; + gpio = <&gpio5 19 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&vcc50_hdmi_en>; +}; + +&pinctrl { + backlight { + bl_pwr_en: bl_pwr_en { + rockchip,pins = <2 12 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + buck-5v { + drv_5v: drv-5v { + rockchip,pins = <7 21 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + edp { + edp_hpd: edp_hpd { + rockchip,pins = <7 11 RK_FUNC_2 &pcfg_pull_down>; + }; + }; + + hdmi { + vcc50_hdmi_en: vcc50-hdmi-en { + rockchip,pins = <5 19 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + lcd { + lcd_enable_h: lcd-en { + rockchip,pins = <7 14 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + avdd_1v8_disp_en: avdd-1v8-disp-en { + rockchip,pins = <2 13 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + pmic { + dvs_1: dvs-1 { + rockchip,pins = <7 12 RK_FUNC_GPIO &pcfg_pull_down>; + }; + + dvs_2: dvs-2 { + rockchip,pins = <7 15 RK_FUNC_GPIO &pcfg_pull_down>; + }; + }; +}; diff --git a/arch/arm/boot/dts/rk3288-veyron.dtsi b/arch/arm/boot/dts/rk3288-veyron.dtsi index 860cea0a7613..5e61f07724d4 100644 --- a/arch/arm/boot/dts/rk3288-veyron.dtsi +++ b/arch/arm/boot/dts/rk3288-veyron.dtsi @@ -550,18 +550,6 @@ }; }; - /* - * On Marvell-based hardware this is a no-connect. Make sure we enable - * the pullup so that the line doesn't float. The pullup shouldn't - * hurt on Broadcom-based hardware since the other side is actively - * driving this signal. As proof: we've already got a pullup on RX. - */ - uart0 { - uart0_cts: uart0-cts { - rockchip,pins = <4 18 RK_FUNC_1 &pcfg_pull_up>; - }; - }; - write-protect { fw_wp_ap: fw-wp-ap { rockchip,pins = <7 6 RK_FUNC_GPIO &pcfg_pull_none>; diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi index 4e7c6b7392af..6a79c9c526b8 100644 --- a/arch/arm/boot/dts/rk3288.dtsi +++ b/arch/arm/boot/dts/rk3288.dtsi @@ -44,6 +44,7 @@ #include <dt-bindings/pinctrl/rockchip.h> #include <dt-bindings/clock/rk3288-cru.h> #include <dt-bindings/thermal/thermal.h> +#include <dt-bindings/power/rk3288-power.h> #include "skeleton.dtsi" / { @@ -617,8 +618,98 @@ }; pmu: power-management@ff730000 { - compatible = "rockchip,rk3288-pmu", "syscon"; + compatible = "rockchip,rk3288-pmu", "syscon", "simple-mfd"; reg = <0xff730000 0x100>; + + power: power-controller { + compatible = "rockchip,rk3288-power-controller"; + #power-domain-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + /* + * Note: Although SCLK_* are the working clocks + * of device without including on the NOC, needed for + * synchronous reset. + * + * The clocks on the which NOC: + * ACLK_IEP/ACLK_VIP/ACLK_VOP0 are on ACLK_VIO0_NIU. + * ACLK_ISP/ACLK_VOP1 are on ACLK_VIO1_NIU. + * ACLK_RGA is on ACLK_RGA_NIU. + * The others (HCLK_*,PLCK_*) are on HCLK_VIO_NIU. + * + * Which clock are device clocks: + * clocks devices + * *_IEP IEP:Image Enhancement Processor + * *_ISP ISP:Image Signal Processing + * *_VIP VIP:Video Input Processor + * *_VOP* VOP:Visual Output Processor + * *_RGA RGA + * *_EDP* EDP + * *_LVDS_* LVDS + * *_HDMI HDMI + * *_MIPI_* MIPI + */ + pd_vio { + reg = <RK3288_PD_VIO>; + clocks = <&cru ACLK_IEP>, + <&cru ACLK_ISP>, + <&cru ACLK_RGA>, + <&cru ACLK_VIP>, + <&cru ACLK_VOP0>, + <&cru ACLK_VOP1>, + <&cru DCLK_VOP0>, + <&cru DCLK_VOP1>, + <&cru HCLK_IEP>, + <&cru HCLK_ISP>, + <&cru HCLK_RGA>, + <&cru HCLK_VIP>, + <&cru HCLK_VOP0>, + <&cru HCLK_VOP1>, + <&cru PCLK_EDP_CTRL>, + <&cru PCLK_HDMI_CTRL>, + <&cru PCLK_LVDS_PHY>, + <&cru PCLK_MIPI_CSI>, + <&cru PCLK_MIPI_DSI0>, + <&cru PCLK_MIPI_DSI1>, + <&cru SCLK_EDP_24M>, + <&cru SCLK_EDP>, + <&cru SCLK_ISP_JPE>, + <&cru SCLK_ISP>, + <&cru SCLK_RGA>; + }; + + /* + * Note: The following 3 are HEVC(H.265) clocks, + * and on the ACLK_HEVC_NIU (NOC). + */ + pd_hevc { + reg = <RK3288_PD_HEVC>; + clocks = <&cru ACLK_HEVC>, + <&cru SCLK_HEVC_CABAC>, + <&cru SCLK_HEVC_CORE>; + }; + + /* + * Note: ACLK_VCODEC/HCLK_VCODEC are VCODEC + * (video endecoder & decoder) clocks that on the + * ACLK_VCODEC_NIU and HCLK_VCODEC_NIU (NOC). + */ + pd_video { + reg = <RK3288_PD_VIDEO>; + clocks = <&cru ACLK_VCODEC>, + <&cru HCLK_VCODEC>; + }; + + /* + * Note: ACLK_GPU is the GPU clock, + * and on the ACLK_GPU_NIU (NOC). + */ + pd_gpu { + reg = <RK3288_PD_GPU>; + clocks = <&cru ACLK_GPU>; + }; + }; }; sgrf: syscon@ff740000 { @@ -657,6 +748,21 @@ status = "disabled"; }; + spdif: sound@ff88b0000 { + compatible = "rockchip,rk3288-spdif", "rockchip,rk3066-spdif"; + reg = <0xff8b0000 0x10000>; + #sound-dai-cells = <0>; + clock-names = "hclk", "mclk"; + clocks = <&cru HCLK_SPDIF8CH>, <&cru SCLK_SPDIF8CH>; + dmas = <&dmac_bus_s 3>; + dma-names = "tx"; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&spdif_tx>; + rockchip,grf = <&grf>; + status = "disabled"; + }; + i2s: i2s@ff890000 { compatible = "rockchip,rk3288-i2s", "rockchip,rk3066-i2s"; reg = <0xff890000 0x10000>; @@ -678,6 +784,7 @@ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cru ACLK_VOP0>, <&cru DCLK_VOP0>, <&cru HCLK_VOP0>; clock-names = "aclk_vop", "dclk_vop", "hclk_vop"; + power-domains = <&power RK3288_PD_VIO>; resets = <&cru SRST_LCDC0_AXI>, <&cru SRST_LCDC0_AHB>, <&cru SRST_LCDC0_DCLK>; reset-names = "axi", "ahb", "dclk"; iommus = <&vopb_mmu>; @@ -699,6 +806,7 @@ reg = <0xff930300 0x100>; interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "vopb_mmu"; + power-domains = <&power RK3288_PD_VIO>; #iommu-cells = <0>; status = "disabled"; }; @@ -709,6 +817,7 @@ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cru ACLK_VOP1>, <&cru DCLK_VOP1>, <&cru HCLK_VOP1>; clock-names = "aclk_vop", "dclk_vop", "hclk_vop"; + power-domains = <&power RK3288_PD_VIO>; resets = <&cru SRST_LCDC1_AXI>, <&cru SRST_LCDC1_AHB>, <&cru SRST_LCDC1_DCLK>; reset-names = "axi", "ahb", "dclk"; iommus = <&vopl_mmu>; @@ -730,6 +839,7 @@ reg = <0xff940300 0x100>; interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "vopl_mmu"; + power-domains = <&power RK3288_PD_VIO>; #iommu-cells = <0>; status = "disabled"; }; @@ -742,6 +852,7 @@ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_HDCP>; clock-names = "iahb", "isfr"; + power-domains = <&power RK3288_PD_VIO>; status = "disabled"; ports { @@ -927,6 +1038,13 @@ #interrupt-cells = <2>; }; + hdmi { + hdmi_ddc: hdmi-ddc { + rockchip,pins = <7 19 RK_FUNC_2 &pcfg_pull_none>, + <7 20 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + pcfg_pull_up: pcfg-pull-up { bias-pull-up; }; @@ -1215,7 +1333,7 @@ }; uart0_cts: uart0-cts { - rockchip,pins = <4 18 RK_FUNC_1 &pcfg_pull_none>; + rockchip,pins = <4 18 RK_FUNC_1 &pcfg_pull_up>; }; uart0_rts: uart0-rts { @@ -1230,7 +1348,7 @@ }; uart1_cts: uart1-cts { - rockchip,pins = <5 10 RK_FUNC_1 &pcfg_pull_none>; + rockchip,pins = <5 10 RK_FUNC_1 &pcfg_pull_up>; }; uart1_rts: uart1-rts { @@ -1253,7 +1371,7 @@ }; uart3_cts: uart3-cts { - rockchip,pins = <7 9 RK_FUNC_1 &pcfg_pull_none>; + rockchip,pins = <7 9 RK_FUNC_1 &pcfg_pull_up>; }; uart3_rts: uart3-rts { @@ -1268,7 +1386,7 @@ }; uart4_cts: uart4-cts { - rockchip,pins = <5 14 3 &pcfg_pull_none>; + rockchip,pins = <5 14 3 &pcfg_pull_up>; }; uart4_rts: uart4-rts { @@ -1338,5 +1456,11 @@ <4 3 3 &pcfg_pull_none>; }; }; + + spdif { + spdif_tx: spdif-tx { + rockchip,pins = <RK_GPIO6 11 RK_FUNC_1 &pcfg_pull_none>; + }; + }; }; }; diff --git a/arch/arm/boot/dts/s3c2416.dtsi b/arch/arm/boot/dts/s3c2416.dtsi index a5184ff56933..80f007550324 100644 --- a/arch/arm/boot/dts/s3c2416.dtsi +++ b/arch/arm/boot/dts/s3c2416.dtsi @@ -25,7 +25,7 @@ #size-cells = <0>; cpu { - compatible = "arm,arm926ejs"; + compatible = "arm,arm926ej-s"; }; }; diff --git a/arch/arm/boot/dts/s5pv210-aquila.dts b/arch/arm/boot/dts/s5pv210-aquila.dts index f00cea7aca2f..aa64faa72970 100644 --- a/arch/arm/boot/dts/s5pv210-aquila.dts +++ b/arch/arm/boot/dts/s5pv210-aquila.dts @@ -46,7 +46,7 @@ regulator-name = "V_TF_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpios = <&mp05 4 0>; + gpio = <&mp05 4 0>; enable-active-high; }; diff --git a/arch/arm/boot/dts/s5pv210-goni.dts b/arch/arm/boot/dts/s5pv210-goni.dts index a3d4643b202e..3b76eeeb8410 100644 --- a/arch/arm/boot/dts/s5pv210-goni.dts +++ b/arch/arm/boot/dts/s5pv210-goni.dts @@ -47,7 +47,7 @@ regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; reg = <0>; - gpios = <&mp05 4 0>; + gpio = <&mp05 4 0>; enable-active-high; }; @@ -73,7 +73,7 @@ regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; reg = <3>; - gpios = <&gpj1 3 0>; + gpio = <&gpj1 3 0>; enable-active-high; }; }; diff --git a/arch/arm/boot/dts/sama5d2-pinfunc.h b/arch/arm/boot/dts/sama5d2-pinfunc.h new file mode 100644 index 000000000000..1afe24629d1f --- /dev/null +++ b/arch/arm/boot/dts/sama5d2-pinfunc.h @@ -0,0 +1,880 @@ +#define PINMUX_PIN(no, func, ioset) \ +(((no) & 0xffff) | (((func) & 0xf) << 16) | (((ioset) & 0xff) << 20)) + +#define PIN_PA0 0 +#define PIN_PA0__GPIO PINMUX_PIN(PIN_PA0, 0, 0) +#define PIN_PA0__SDMMC0_CK PINMUX_PIN(PIN_PA0, 1, 1) +#define PIN_PA0__QSPI0_SCK PINMUX_PIN(PIN_PA0, 2, 1) +#define PIN_PA0__D0 PINMUX_PIN(PIN_PA0, 6, 2) +#define PIN_PA1 1 +#define PIN_PA1__GPIO PINMUX_PIN(PIN_PA1, 0, 0) +#define PIN_PA1__SDMMC0_CMD PINMUX_PIN(PIN_PA1, 1, 1) +#define PIN_PA1__QSPI0_CS PINMUX_PIN(PIN_PA1, 2, 1) +#define PIN_PA1__D1 PINMUX_PIN(PIN_PA1, 6, 2) +#define PIN_PA2 2 +#define PIN_PA2__GPIO PINMUX_PIN(PIN_PA2, 0, 0) +#define PIN_PA2__SDMMC0_DAT0 PINMUX_PIN(PIN_PA2, 1, 1) +#define PIN_PA2__QSPI0_IO0 PINMUX_PIN(PIN_PA2, 2, 1) +#define PIN_PA2__D2 PINMUX_PIN(PIN_PA2, 6, 2) +#define PIN_PA3 3 +#define PIN_PA3__GPIO PINMUX_PIN(PIN_PA3, 0, 0) +#define PIN_PA3__SDMMC0_DAT1 PINMUX_PIN(PIN_PA3, 1, 1) +#define PIN_PA3__QSPI0_IO1 PINMUX_PIN(PIN_PA3, 2, 1) +#define PIN_PA3__D3 PINMUX_PIN(PIN_PA3, 6, 2) +#define PIN_PA4 4 +#define PIN_PA4__GPIO PINMUX_PIN(PIN_PA4, 0, 0) +#define PIN_PA4__SDMMC0_DAT2 PINMUX_PIN(PIN_PA4, 1, 1) +#define PIN_PA4__QSPI0_IO2 PINMUX_PIN(PIN_PA4, 2, 1) +#define PIN_PA4__D4 PINMUX_PIN(PIN_PA4, 6, 2) +#define PIN_PA5 5 +#define PIN_PA5__GPIO PINMUX_PIN(PIN_PA5, 0, 0) +#define PIN_PA5__SDMMC0_DAT3 PINMUX_PIN(PIN_PA5, 1, 1) +#define PIN_PA5__QSPI0_IO3 PINMUX_PIN(PIN_PA5, 2, 1) +#define PIN_PA5__D5 PINMUX_PIN(PIN_PA5, 6, 2) +#define PIN_PA6 6 +#define PIN_PA6__GPIO PINMUX_PIN(PIN_PA6, 0, 0) +#define PIN_PA6__SDMMC0_DAT4 PINMUX_PIN(PIN_PA6, 1, 1) +#define PIN_PA6__QSPI1_SCK PINMUX_PIN(PIN_PA6, 2, 1) +#define PIN_PA6__TIOA5 PINMUX_PIN(PIN_PA6, 4, 1) +#define PIN_PA6__FLEXCOM2_IO0 PINMUX_PIN(PIN_PA6, 5, 1) +#define PIN_PA6__D6 PINMUX_PIN(PIN_PA6, 6, 2) +#define PIN_PA7 7 +#define PIN_PA7__GPIO PINMUX_PIN(PIN_PA7, 0, 0) +#define PIN_PA7__SDMMC0_DAT5 PINMUX_PIN(PIN_PA7, 1, 1) +#define PIN_PA7__QSPI1_IO0 PINMUX_PIN(PIN_PA7, 2, 1) +#define PIN_PA7__TIOB5 PINMUX_PIN(PIN_PA7, 4, 1) +#define PIN_PA7__FLEXCOM2_IO1 PINMUX_PIN(PIN_PA7, 5, 1) +#define PIN_PA7__D7 PINMUX_PIN(PIN_PA7, 6, 2) +#define PIN_PA8 8 +#define PIN_PA8__GPIO PINMUX_PIN(PIN_PA8, 0, 0) +#define PIN_PA8__SDMMC0_DAT6 PINMUX_PIN(PIN_PA8, 1, 1) +#define PIN_PA8__QSPI1_IO1 PINMUX_PIN(PIN_PA8, 2, 1) +#define PIN_PA8__TCLK5 PINMUX_PIN(PIN_PA8, 4, 1) +#define PIN_PA8__FLEXCOM2_IO2 PINMUX_PIN(PIN_PA8, 5, 1) +#define PIN_PA8__NWE_NANDWE PINMUX_PIN(PIN_PA8, 6, 2) +#define PIN_PA9 9 +#define PIN_PA9__GPIO PINMUX_PIN(PIN_PA9, 0, 0) +#define PIN_PA9__SDMMC0_DAT7 PINMUX_PIN(PIN_PA9, 1, 1) +#define PIN_PA9__QSPI1_IO2 PINMUX_PIN(PIN_PA9, 2, 1) +#define PIN_PA9__TIOA4 PINMUX_PIN(PIN_PA9, 4, 1) +#define PIN_PA9__FLEXCOM2_IO3 PINMUX_PIN(PIN_PA9, 5, 1) +#define PIN_PA9__NCS3 PINMUX_PIN(PIN_PA9, 6, 2) +#define PIN_PA10 10 +#define PIN_PA10__GPIO PINMUX_PIN(PIN_PA10, 0, 0) +#define PIN_PA10__SDMMC0_RSTN PINMUX_PIN(PIN_PA10, 1, 1) +#define PIN_PA10__QSPI1_IO3 PINMUX_PIN(PIN_PA10, 2, 1) +#define PIN_PA10__TIOB4 PINMUX_PIN(PIN_PA10, 4, 1) +#define PIN_PA10__FLEXCOM2_IO4 PINMUX_PIN(PIN_PA10, 5, 1) +#define PIN_PA10__A21_NANDALE PINMUX_PIN(PIN_PA10, 6, 2) +#define PIN_PA11 11 +#define PIN_PA11__GPIO PINMUX_PIN(PIN_PA11, 0, 0) +#define PIN_PA11__SDMMC0_VDDSEL PINMUX_PIN(PIN_PA11, 1, 1) +#define PIN_PA11__QSPI1_CS PINMUX_PIN(PIN_PA11, 2, 1) +#define PIN_PA11__TCLK4 PINMUX_PIN(PIN_PA11, 4, 1) +#define PIN_PA11__A22_NANDCLE PINMUX_PIN(PIN_PA11, 6, 2) +#define PIN_PA12 12 +#define PIN_PA12__GPIO PINMUX_PIN(PIN_PA12, 0, 0) +#define PIN_PA12__SDMMC0_WP PINMUX_PIN(PIN_PA12, 1, 1) +#define PIN_PA12__IRQ PINMUX_PIN(PIN_PA12, 2, 1) +#define PIN_PA12__NRD_NANDOE PINMUX_PIN(PIN_PA12, 6, 2) +#define PIN_PA13 13 +#define PIN_PA13__GPIO PINMUX_PIN(PIN_PA13, 0, 0) +#define PIN_PA13__SDMMC0_CD PINMUX_PIN(PIN_PA13, 1, 1) +#define PIN_PA13__FLEXCOM3_IO1 PINMUX_PIN(PIN_PA13, 5, 1) +#define PIN_PA13__D8 PINMUX_PIN(PIN_PA13, 6, 2) +#define PIN_PA14 14 +#define PIN_PA14__GPIO PINMUX_PIN(PIN_PA14, 0, 0) +#define PIN_PA14__SPI0_SPCK PINMUX_PIN(PIN_PA14, 1, 1) +#define PIN_PA14__TK1 PINMUX_PIN(PIN_PA14, 2, 1) +#define PIN_PA14__QSPI0_SCK PINMUX_PIN(PIN_PA14, 3, 2) +#define PIN_PA14__I2SC1_MCK PINMUX_PIN(PIN_PA14, 4, 2) +#define PIN_PA14__FLEXCOM3_IO2 PINMUX_PIN(PIN_PA14, 5, 1) +#define PIN_PA14__D9 PINMUX_PIN(PIN_PA14, 6, 2) +#define PIN_PA15 14 +#define PIN_PA15__GPIO PINMUX_PIN(PIN_PA15, 0, 0) +#define PIN_PA15__SPI0_MOSI PINMUX_PIN(PIN_PA15, 1, 1) +#define PIN_PA15__TF1 PINMUX_PIN(PIN_PA15, 2, 1) +#define PIN_PA15__QSPI0_CS PINMUX_PIN(PIN_PA15, 3, 2) +#define PIN_PA15__I2SC1_CK PINMUX_PIN(PIN_PA15, 4, 2) +#define PIN_PA15__FLEXCOM3_IO0 PINMUX_PIN(PIN_PA15, 5, 1) +#define PIN_PA15__D10 PINMUX_PIN(PIN_PA15, 6, 2) +#define PIN_PA16 16 +#define PIN_PA16__GPIO PINMUX_PIN(PIN_PA16, 0, 0) +#define PIN_PA16__SPI0_MISO PINMUX_PIN(PIN_PA16, 1, 1) +#define PIN_PA16__TD1 PINMUX_PIN(PIN_PA16, 2, 1) +#define PIN_PA16__QSPI0_IO0 PINMUX_PIN(PIN_PA16, 3, 2) +#define PIN_PA16__I2SC1_WS PINMUX_PIN(PIN_PA16, 4, 2) +#define PIN_PA16__FLEXCOM3_IO3 PINMUX_PIN(PIN_PA16, 5, 1) +#define PIN_PA16__D11 PINMUX_PIN(PIN_PA16, 6, 2) +#define PIN_PA17 17 +#define PIN_PA17__GPIO PINMUX_PIN(PIN_PA17, 0, 0) +#define PIN_PA17__SPI0_NPCS0 PINMUX_PIN(PIN_PA17, 1, 1) +#define PIN_PA17__RD1 PINMUX_PIN(PIN_PA17, 2, 1) +#define PIN_PA17__QSPI0_IO1 PINMUX_PIN(PIN_PA17, 3, 2) +#define PIN_PA17__I2SC1_DI0 PINMUX_PIN(PIN_PA17, 4, 2) +#define PIN_PA17__FLEXCOM3_IO4 PINMUX_PIN(PIN_PA17, 5, 1) +#define PIN_PA17__D12 PINMUX_PIN(PIN_PA17, 6, 2) +#define PIN_PA18 18 +#define PIN_PA18__GPIO PINMUX_PIN(PIN_PA18, 0, 0) +#define PIN_PA18__SPI0_NPCS1 PINMUX_PIN(PIN_PA18, 1, 1) +#define PIN_PA18__RK1 PINMUX_PIN(PIN_PA18, 2, 1) +#define PIN_PA18__QSPI0_IO2 PINMUX_PIN(PIN_PA18, 3, 2) +#define PIN_PA18__I2SC1_DO0 PINMUX_PIN(PIN_PA18, 4, 2) +#define PIN_PA18__SDMMC1_DAT0 PINMUX_PIN(PIN_PA18, 5, 1) +#define PIN_PA18__D13 PINMUX_PIN(PIN_PA18, 6, 2) +#define PIN_PA19 19 +#define PIN_PA19__GPIO PINMUX_PIN(PIN_PA19, 0, 0) +#define PIN_PA19__SPI0_NPCS2 PINMUX_PIN(PIN_PA19, 1, 1) +#define PIN_PA19__RF1 PINMUX_PIN(PIN_PA19, 2, 1) +#define PIN_PA19__QSPI0_IO3 PINMUX_PIN(PIN_PA19, 3, 2) +#define PIN_PA19__TIOA0 PINMUX_PIN(PIN_PA19, 4, 1) +#define PIN_PA19__SDMMC1_DAT1 PINMUX_PIN(PIN_PA19, 5, 1) +#define PIN_PA19__D14 PINMUX_PIN(PIN_PA19, 6, 2) +#define PIN_PA20 20 +#define PIN_PA20__GPIO PINMUX_PIN(PIN_PA20, 0, 0) +#define PIN_PA20__SPI0_NPCS3 PINMUX_PIN(PIN_PA20, 1, 1) +#define PIN_PA20__TIOB0 PINMUX_PIN(PIN_PA20, 4, 1) +#define PIN_PA20__SDMMC1_DAT2 PINMUX_PIN(PIN_PA20, 5, 1) +#define PIN_PA20__D15 PINMUX_PIN(PIN_PA20, 6, 2) +#define PIN_PA21 21 +#define PIN_PA21__GPIO PINMUX_PIN(PIN_PA21, 0, 0) +#define PIN_PA21__IRQ PINMUX_PIN(PIN_PA21, 1, 2) +#define PIN_PA21__PCK2 PINMUX_PIN(PIN_PA21, 2, 3) +#define PIN_PA21__TCLK0 PINMUX_PIN(PIN_PA21, 4, 1) +#define PIN_PA21__SDMMC1_DAT3 PINMUX_PIN(PIN_PA21, 5, 1) +#define PIN_PA21__NANDRDY PINMUX_PIN(PIN_PA21, 6, 2) +#define PIN_PA22 22 +#define PIN_PA22__GPIO PINMUX_PIN(PIN_PA22, 0, 0) +#define PIN_PA22__FLEXCOM1_IO2 PINMUX_PIN(PIN_PA22, 1, 1) +#define PIN_PA22__D0 PINMUX_PIN(PIN_PA22, 2, 1) +#define PIN_PA22__TCK PINMUX_PIN(PIN_PA22, 3, 4) +#define PIN_PA22__SPI1_SPCK PINMUX_PIN(PIN_PA22, 4, 2) +#define PIN_PA22__SDMMC1_CK PINMUX_PIN(PIN_PA22, 5, 1) +#define PIN_PA22__QSPI0_SCK PINMUX_PIN(PIN_PA22, 6, 3) +#define PIN_PA23 23 +#define PIN_PA23__GPIO PINMUX_PIN(PIN_PA23, 0, 0) +#define PIN_PA23__FLEXCOM1_IO1 PINMUX_PIN(PIN_PA23, 1, 1) +#define PIN_PA23__D1 PINMUX_PIN(PIN_PA23, 2, 1) +#define PIN_PA23__TDI PINMUX_PIN(PIN_PA23, 3, 4) +#define PIN_PA23__SPI1_MOSI PINMUX_PIN(PIN_PA23, 4, 2) +#define PIN_PA23__QSPI0_CS PINMUX_PIN(PIN_PA23, 6, 3) +#define PIN_PA24 24 +#define PIN_PA24__GPIO PINMUX_PIN(PIN_PA24, 0, 0) +#define PIN_PA24__FLEXCOM1_IO0 PINMUX_PIN(PIN_PA24, 1, 1) +#define PIN_PA24__D2 PINMUX_PIN(PIN_PA24, 2, 1) +#define PIN_PA24__TDO PINMUX_PIN(PIN_PA24, 3, 4) +#define PIN_PA24__SPI1_MISO PINMUX_PIN(PIN_PA24, 4, 2) +#define PIN_PA24__QSPI0_IO0 PINMUX_PIN(PIN_PA24, 6, 3) +#define PIN_PA25 25 +#define PIN_PA25__GPIO PINMUX_PIN(PIN_PA25, 0, 0) +#define PIN_PA25__FLEXCOM1_IO3 PINMUX_PIN(PIN_PA25, 1, 1) +#define PIN_PA25__D3 PINMUX_PIN(PIN_PA25, 2, 1) +#define PIN_PA25__TMS PINMUX_PIN(PIN_PA25, 3, 4) +#define PIN_PA25__SPI1_NPCS0 PINMUX_PIN(PIN_PA25, 4, 2) +#define PIN_PA25__QSPI0_IO1 PINMUX_PIN(PIN_PA25, 6, 3) +#define PIN_PA26 26 +#define PIN_PA26__GPIO PINMUX_PIN(PIN_PA26, 0, 0) +#define PIN_PA26__FLEXCOM1_IO4 PINMUX_PIN(PIN_PA26, 1, 1) +#define PIN_PA26__D4 PINMUX_PIN(PIN_PA26, 2, 1) +#define PIN_PA26__NTRST PINMUX_PIN(PIN_PA26, 3, 4) +#define PIN_PA26__SPI1_NPCS1 PINMUX_PIN(PIN_PA26, 4, 2) +#define PIN_PA26__QSPI0_IO2 PINMUX_PIN(PIN_PA26, 6, 3) +#define PIN_PA27 27 +#define PIN_PA27__GPIO PINMUX_PIN(PIN_PA27, 0, 0) +#define PIN_PA27__TIOA1 PINMUX_PIN(PIN_PA27, 1, 2) +#define PIN_PA27__D5 PINMUX_PIN(PIN_PA27, 2, 1) +#define PIN_PA27__SPI0_NPCS2 PINMUX_PIN(PIN_PA27, 3, 2) +#define PIN_PA27__SPI1_NPCS2 PINMUX_PIN(PIN_PA27, 4, 2) +#define PIN_PA27__SDMMC1_RSTN PINMUX_PIN(PIN_PA27, 5, 1) +#define PIN_PA27__QSPI0_IO3 PINMUX_PIN(PIN_PA27, 6, 3) +#define PIN_PA28 28 +#define PIN_PA28__GPIO PINMUX_PIN(PIN_PA28, 0, 0) +#define PIN_PA28__TIOB1 PINMUX_PIN(PIN_PA28, 1, 2) +#define PIN_PA28__D6 PINMUX_PIN(PIN_PA28, 2, 1) +#define PIN_PA28__SPI0_NPCS3 PINMUX_PIN(PIN_PA28, 3, 2) +#define PIN_PA28__SPI1_NPCS3 PINMUX_PIN(PIN_PA28, 4, 2) +#define PIN_PA28__SDMMC1_CMD PINMUX_PIN(PIN_PA28, 5, 1) +#define PIN_PA28__CLASSD_L0 PINMUX_PIN(PIN_PA28, 6, 1) +#define PIN_PA29 29 +#define PIN_PA29__GPIO PINMUX_PIN(PIN_PA29, 0, 0) +#define PIN_PA29__TCLK1 PINMUX_PIN(PIN_PA29, 1, 2) +#define PIN_PA29__D7 PINMUX_PIN(PIN_PA29, 2, 1) +#define PIN_PA29__SPI0_NPCS1 PINMUX_PIN(PIN_PA29, 3, 2) +#define PIN_PA29__SDMMC1_WP PINMUX_PIN(PIN_PA29, 5, 1) +#define PIN_PA29__CLASSD_L1 PINMUX_PIN(PIN_PA29, 6, 1) +#define PIN_PA30 30 +#define PIN_PA30__GPIO PINMUX_PIN(PIN_PA30, 0, 0) +#define PIN_PA30__NWE_NANDWE PINMUX_PIN(PIN_PA30, 2, 1) +#define PIN_PA30__SPI0_NPCS0 PINMUX_PIN(PIN_PA30, 3, 2) +#define PIN_PA30__PWMH0 PINMUX_PIN(PIN_PA30, 4, 1) +#define PIN_PA30__SDMMC1_CD PINMUX_PIN(PIN_PA30, 5, 1) +#define PIN_PA30__CLASSD_L2 PINMUX_PIN(PIN_PA30, 6, 1) +#define PIN_PA31 31 +#define PIN_PA31__GPIO PINMUX_PIN(PIN_PA31, 0, 0) +#define PIN_PA31__NCS3 PINMUX_PIN(PIN_PA31, 2, 1) +#define PIN_PA31__SPI0_MISO PINMUX_PIN(PIN_PA31, 3, 2) +#define PIN_PA31__PWML0 PINMUX_PIN(PIN_PA31, 4, 1) +#define PIN_PA31__CLASSD_L3 PINMUX_PIN(PIN_PA31, 6, 1) +#define PIN_PB0 32 +#define PIN_PB0__GPIO PINMUX_PIN(PIN_PB0, 0, 0) +#define PIN_PB0__A21_NANDALE PINMUX_PIN(PIN_PB0, 2, 1) +#define PIN_PB0__SPI0_MOSI PINMUX_PIN(PIN_PB0, 3, 2) +#define PIN_PB0__PWMH1 PINMUX_PIN(PIN_PB0, 4, 1) +#define PIN_PB1 33 +#define PIN_PB1__GPIO PINMUX_PIN(PIN_PB1, 0, 0) +#define PIN_PB1__A22_NANDCLE PINMUX_PIN(PIN_PB1, 2, 1) +#define PIN_PB1__SPI0_SPCK PINMUX_PIN(PIN_PB1, 3, 2) +#define PIN_PB1__PWML1 PINMUX_PIN(PIN_PB1, 4, 1) +#define PIN_PB1__CLASSD_R0 PINMUX_PIN(PIN_PB1, 6, 1) +#define PIN_PB2 34 +#define PIN_PB2__GPIO PINMUX_PIN(PIN_PB2, 0, 0) +#define PIN_PB2__NRD_NANDOE PINMUX_PIN(PIN_PB2, 2, 1) +#define PIN_PB2__PWMFI0 PINMUX_PIN(PIN_PB2, 4, 1) +#define PIN_PB2__CLASSD_R1 PINMUX_PIN(PIN_PB2, 6, 1) +#define PIN_PB3 35 +#define PIN_PB3__GPIO PINMUX_PIN(PIN_PB3, 0, 0) +#define PIN_PB3__URXD4 PINMUX_PIN(PIN_PB3, 1, 1) +#define PIN_PB3__D8 PINMUX_PIN(PIN_PB3, 2, 1) +#define PIN_PB3__IRQ PINMUX_PIN(PIN_PB3, 3, 3) +#define PIN_PB3__PWMEXTRG0 PINMUX_PIN(PIN_PB3, 4, 1) +#define PIN_PB3__CLASSD_R2 PINMUX_PIN(PIN_PB3, 6, 1) +#define PIN_PB4 36 +#define PIN_PB4__GPIO PINMUX_PIN(PIN_PB4, 0, 0) +#define PIN_PB4__UTXD4 PINMUX_PIN(PIN_PB4, 1, 1) +#define PIN_PB4__D9 PINMUX_PIN(PIN_PB4, 2, 1) +#define PIN_PB4__FIQ PINMUX_PIN(PIN_PB4, 3, 4) +#define PIN_PB4__CLASSD_R3 PINMUX_PIN(PIN_PB4, 6, 1) +#define PIN_PB5 37 +#define PIN_PB5__GPIO PINMUX_PIN(PIN_PB5, 0, 0) +#define PIN_PB5__TCLK2 PINMUX_PIN(PIN_PB5, 1, 1) +#define PIN_PB5__D10 PINMUX_PIN(PIN_PB5, 2, 1) +#define PIN_PB5__PWMH2 PINMUX_PIN(PIN_PB5, 3, 1) +#define PIN_PB5__QSPI1_SCK PINMUX_PIN(PIN_PB5, 4, 2) +#define PIN_PB5__GTSUCOMP PINMUX_PIN(PIN_PB5, 6, 3) +#define PIN_PB6 38 +#define PIN_PB6__GPIO PINMUX_PIN(PIN_PB6, 0, 0) +#define PIN_PB6__TIOA2 PINMUX_PIN(PIN_PB6, 1, 1) +#define PIN_PB6__D11 PINMUX_PIN(PIN_PB6, 2, 1) +#define PIN_PB6__PWML2 PINMUX_PIN(PIN_PB6, 3, 1) +#define PIN_PB6__QSPI1_CS PINMUX_PIN(PIN_PB6, 4, 2) +#define PIN_PB6__GTXER PINMUX_PIN(PIN_PB6, 6, 3) +#define PIN_PB7 39 +#define PIN_PB7__GPIO PINMUX_PIN(PIN_PB7, 0, 0) +#define PIN_PB7__TIOB2 PINMUX_PIN(PIN_PB7, 1, 1) +#define PIN_PB7__D12 PINMUX_PIN(PIN_PB7, 2, 1) +#define PIN_PB7__PWMH3 PINMUX_PIN(PIN_PB7, 3, 1) +#define PIN_PB7__QSPI1_IO0 PINMUX_PIN(PIN_PB7, 4, 2) +#define PIN_PB7__GRXCK PINMUX_PIN(PIN_PB7, 6, 3) +#define PIN_PB8 40 +#define PIN_PB8__GPIO PINMUX_PIN(PIN_PB8, 0, 0) +#define PIN_PB8__TCLK3 PINMUX_PIN(PIN_PB8, 1, 1) +#define PIN_PB8__D13 PINMUX_PIN(PIN_PB8, 2, 1) +#define PIN_PB8__PWML3 PINMUX_PIN(PIN_PB8, 3, 1) +#define PIN_PB8__QSPI1_IO1 PINMUX_PIN(PIN_PB8, 4, 2) +#define PIN_PB8__GCRS PINMUX_PIN(PIN_PB8, 6, 3) +#define PIN_PB9 41 +#define PIN_PB9__GPIO PINMUX_PIN(PIN_PB9, 0, 0) +#define PIN_PB9__TIOA3 PINMUX_PIN(PIN_PB9, 1, 1) +#define PIN_PB9__D14 PINMUX_PIN(PIN_PB9, 2, 1) +#define PIN_PB9__PWMFI1 PINMUX_PIN(PIN_PB9, 3, 1) +#define PIN_PB9__QSPI1_IO2 PINMUX_PIN(PIN_PB9, 4, 2) +#define PIN_PB9__GCOL PINMUX_PIN(PIN_PB9, 6, 3) +#define PIN_PB10 42 +#define PIN_PB10__GPIO PINMUX_PIN(PIN_PB10, 0, 0) +#define PIN_PB10__TIOB3 PINMUX_PIN(PIN_PB10, 1, 1) +#define PIN_PB10__D15 PINMUX_PIN(PIN_PB10, 2, 1) +#define PIN_PB10__PWMEXTRG1 PINMUX_PIN(PIN_PB10, 3, 1) +#define PIN_PB10__QSPI1_IO3 PINMUX_PIN(PIN_PB10, 4, 2) +#define PIN_PB10__GRX2 PINMUX_PIN(PIN_PB10, 6, 3) +#define PIN_PB11 43 +#define PIN_PB11__GPIO PINMUX_PIN(PIN_PB11, 0, 0) +#define PIN_PB11__LCDDAT0 PINMUX_PIN(PIN_PB11, 1, 1) +#define PIN_PB11__A0_NBS0 PINMUX_PIN(PIN_PB11, 2, 1) +#define PIN_PB11__URXD3 PINMUX_PIN(PIN_PB11, 3, 3) +#define PIN_PB11__PDMIC_DAT PINMUX_PIN(PIN_PB11, 4, 2) +#define PIN_PB11__GRX3 PINMUX_PIN(PIN_PB11, 6, 3) +#define PIN_PB12 44 +#define PIN_PB12__GPIO PINMUX_PIN(PIN_PB12, 0, 0) +#define PIN_PB12__LCDDAT1 PINMUX_PIN(PIN_PB12, 1, 1) +#define PIN_PB12__A1 PINMUX_PIN(PIN_PB12, 2, 1) +#define PIN_PB12__UTXD3 PINMUX_PIN(PIN_PB12, 3, 3) +#define PIN_PB12__PDMIC_CLK PINMUX_PIN(PIN_PB12, 4, 2) +#define PIN_PB12__GTX2 PINMUX_PIN(PIN_PB12, 6, 3) +#define PIN_PB13 45 +#define PIN_PB13__GPIO PINMUX_PIN(PIN_PB13, 0, 0) +#define PIN_PB13__LCDDAT2 PINMUX_PIN(PIN_PB13, 1, 1) +#define PIN_PB13__A2 PINMUX_PIN(PIN_PB13, 2, 1) +#define PIN_PB13__PCK1 PINMUX_PIN(PIN_PB13, 3, 3) +#define PIN_PB13__GTX3 PINMUX_PIN(PIN_PB13, 6, 3) +#define PIN_PB14 46 +#define PIN_PB14__GPIO PINMUX_PIN(PIN_PB14, 0, 0) +#define PIN_PB14__LCDDAT3 PINMUX_PIN(PIN_PB14, 1, 1) +#define PIN_PB14__A3 PINMUX_PIN(PIN_PB14, 2, 1) +#define PIN_PB14__TK1 PINMUX_PIN(PIN_PB14, 3, 2) +#define PIN_PB14__I2SC1_MCK PINMUX_PIN(PIN_PB14, 4, 1) +#define PIN_PB14__QSPI1_SCK PINMUX_PIN(PIN_PB14, 5, 3) +#define PIN_PB14__GTXCK PINMUX_PIN(PIN_PB14, 6, 3) +#define PIN_PB15 47 +#define PIN_PB15__GPIO PINMUX_PIN(PIN_PB15, 0, 0) +#define PIN_PB15__LCDDAT4 PINMUX_PIN(PIN_PB15, 1, 1) +#define PIN_PB15__A4 PINMUX_PIN(PIN_PB15, 2, 1) +#define PIN_PB15__TF1 PINMUX_PIN(PIN_PB15, 3, 2) +#define PIN_PB15__I2SC1_CK PINMUX_PIN(PIN_PB15, 4, 1) +#define PIN_PB15__QSPI1_CS PINMUX_PIN(PIN_PB15, 5, 3) +#define PIN_PB15__GTXEN PINMUX_PIN(PIN_PB15, 6, 3) +#define PIN_PB16 48 +#define PIN_PB16__GPIO PINMUX_PIN(PIN_PB16, 0, 0) +#define PIN_PB16__LCDDAT5 PINMUX_PIN(PIN_PB16, 1, 1) +#define PIN_PB16__A5 PINMUX_PIN(PIN_PB16, 2, 1) +#define PIN_PB16__TD1 PINMUX_PIN(PIN_PB16, 3, 2) +#define PIN_PB16__I2SC1_WS PINMUX_PIN(PIN_PB16, 4, 1) +#define PIN_PB16__QSPI1_IO0 PINMUX_PIN(PIN_PB16, 5, 3) +#define PIN_PB16__GRXDV PINMUX_PIN(PIN_PB16, 6, 3) +#define PIN_PB17 49 +#define PIN_PB17__GPIO PINMUX_PIN(PIN_PB17, 0, 0) +#define PIN_PB17__LCDDAT6 PINMUX_PIN(PIN_PB17, 1, 1) +#define PIN_PB17__A6 PINMUX_PIN(PIN_PB17, 2, 1) +#define PIN_PB17__RD1 PINMUX_PIN(PIN_PB17, 3, 2) +#define PIN_PB17__I2SC1_DI0 PINMUX_PIN(PIN_PB17, 4, 1) +#define PIN_PB17__QSPI1_IO1 PINMUX_PIN(PIN_PB17, 5, 3) +#define PIN_PB17__GRXER PINMUX_PIN(PIN_PB17, 6, 3) +#define PIN_PB18 50 +#define PIN_PB18__GPIO PINMUX_PIN(PIN_PB18, 0, 0) +#define PIN_PB18__LCDDAT7 PINMUX_PIN(PIN_PB18, 1, 1) +#define PIN_PB18__A7 PINMUX_PIN(PIN_PB18, 2, 1) +#define PIN_PB18__RK1 PINMUX_PIN(PIN_PB18, 3, 2) +#define PIN_PB18__I2SC1_DO0 PINMUX_PIN(PIN_PB18, 4, 1) +#define PIN_PB18__QSPI1_IO2 PINMUX_PIN(PIN_PB18, 5, 3) +#define PIN_PB18__GRX0 PINMUX_PIN(PIN_PB18, 6, 3) +#define PIN_PB19 51 +#define PIN_PB19__GPIO PINMUX_PIN(PIN_PB19, 0, 0) +#define PIN_PB19__LCDDAT8 PINMUX_PIN(PIN_PB19, 1, 1) +#define PIN_PB19__A8 PINMUX_PIN(PIN_PB19, 2, 1) +#define PIN_PB19__RF1 PINMUX_PIN(PIN_PB19, 3, 2) +#define PIN_PB19__TIOA3 PINMUX_PIN(PIN_PB19, 4, 2) +#define PIN_PB19__QSPI1_IO3 PINMUX_PIN(PIN_PB19, 5, 3) +#define PIN_PB19__GRX1 PINMUX_PIN(PIN_PB19, 6, 3) +#define PIN_PB20 52 +#define PIN_PB20__GPIO PINMUX_PIN(PIN_PB20, 0, 0) +#define PIN_PB20__LCDDAT9 PINMUX_PIN(PIN_PB20, 1, 1) +#define PIN_PB20__A9 PINMUX_PIN(PIN_PB20, 2, 1) +#define PIN_PB20__TK0 PINMUX_PIN(PIN_PB20, 3, 1) +#define PIN_PB20__TIOB3 PINMUX_PIN(PIN_PB20, 4, 2) +#define PIN_PB20__PCK1 PINMUX_PIN(PIN_PB20, 5, 4) +#define PIN_PB20__GTX0 PINMUX_PIN(PIN_PB20, 6, 3) +#define PIN_PB21 53 +#define PIN_PB21__GPIO PINMUX_PIN(PIN_PB21, 0, 0) +#define PIN_PB21__LCDDAT10 PINMUX_PIN(PIN_PB21, 1, 1) +#define PIN_PB21__A10 PINMUX_PIN(PIN_PB21, 2, 1) +#define PIN_PB21__TF0 PINMUX_PIN(PIN_PB21, 3, 1) +#define PIN_PB21__TCLK3 PINMUX_PIN(PIN_PB21, 4, 2) +#define PIN_PB21__FLEXCOM3_IO2 PINMUX_PIN(PIN_PB21, 5, 3) +#define PIN_PB21__GTX1 PINMUX_PIN(PIN_PB21, 6, 3) +#define PIN_PB22 54 +#define PIN_PB22__GPIO PINMUX_PIN(PIN_PB22, 0, 0) +#define PIN_PB22__LCDDAT11 PINMUX_PIN(PIN_PB22, 1, 1) +#define PIN_PB22__A11 PINMUX_PIN(PIN_PB22, 2, 1) +#define PIN_PB22__TDO PINMUX_PIN(PIN_PB22, 3, 1) +#define PIN_PB22__TIOA2 PINMUX_PIN(PIN_PB22, 4, 2) +#define PIN_PB22__FLEXCOM3_IO1 PINMUX_PIN(PIN_PB22, 5, 3) +#define PIN_PB22__GMDC PINMUX_PIN(PIN_PB22, 6, 3) +#define PIN_PB23 55 +#define PIN_PB23__GPIO PINMUX_PIN(PIN_PB23, 0, 0) +#define PIN_PB23__LCDDAT12 PINMUX_PIN(PIN_PB23, 1, 1) +#define PIN_PB23__A12 PINMUX_PIN(PIN_PB23, 2, 1) +#define PIN_PB23__RD0 PINMUX_PIN(PIN_PB23, 3, 1) +#define PIN_PB23__TIOB2 PINMUX_PIN(PIN_PB23, 4, 2) +#define PIN_PB23__FLEXCOM3_IO0 PINMUX_PIN(PIN_PB23, 5, 3) +#define PIN_PB23__GMDIO PINMUX_PIN(PIN_PB23, 6, 3) +#define PIN_PB24 56 +#define PIN_PB24__GPIO PINMUX_PIN(PIN_PB24, 0, 0) +#define PIN_PB24__LCDDAT13 PINMUX_PIN(PIN_PB24, 1, 1) +#define PIN_PB24__A13 PINMUX_PIN(PIN_PB24, 2, 1) +#define PIN_PB24__RK0 PINMUX_PIN(PIN_PB24, 3, 1) +#define PIN_PB24__TCLK2 PINMUX_PIN(PIN_PB24, 4, 2) +#define PIN_PB24__FLEXCOM3_IO3 PINMUX_PIN(PIN_PB24, 5, 3) +#define PIN_PB24__ISC_D10 PINMUX_PIN(PIN_PB24, 6, 3) +#define PIN_PB25 57 +#define PIN_PB25__GPIO PINMUX_PIN(PIN_PB25, 0, 0) +#define PIN_PB25__LCDDAT14 PINMUX_PIN(PIN_PB25, 1, 1) +#define PIN_PB25__A14 PINMUX_PIN(PIN_PB25, 2, 1) +#define PIN_PB25__RF0 PINMUX_PIN(PIN_PB25, 3, 1) +#define PIN_PB25__FLEXCOM3_IO4 PINMUX_PIN(PIN_PB25, 5, 3) +#define PIN_PB25__ISC_D11 PINMUX_PIN(PIN_PB25, 6, 3) +#define PIN_PB26 58 +#define PIN_PB26__GPIO PINMUX_PIN(PIN_PB26, 0, 0) +#define PIN_PB26__LCDDAT15 PINMUX_PIN(PIN_PB26, 1, 1) +#define PIN_PB26__A15 PINMUX_PIN(PIN_PB26, 2, 1) +#define PIN_PB26__URXD0 PINMUX_PIN(PIN_PB26, 3, 1) +#define PIN_PB26__PDMIC_DAT PINMUX_PIN(PIN_PB26, 4, 1) +#define PIN_PB26__ISC_D0 PINMUX_PIN(PIN_PB26, 6, 3) +#define PIN_PB27 59 +#define PIN_PB27__GPIO PINMUX_PIN(PIN_PB27, 0, 0) +#define PIN_PB27__LCDDAT16 PINMUX_PIN(PIN_PB27, 1, 1) +#define PIN_PB27__A16 PINMUX_PIN(PIN_PB27, 2, 1) +#define PIN_PB27__UTXD0 PINMUX_PIN(PIN_PB27, 3, 1) +#define PIN_PB27__PDMIC_CLK PINMUX_PIN(PIN_PB27, 4, 1) +#define PIN_PB27__ISC_D1 PINMUX_PIN(PIN_PB27, 6, 3) +#define PIN_PB28 60 +#define PIN_PB28__GPIO PINMUX_PIN(PIN_PB28, 0, 0) +#define PIN_PB28__LCDDAT17 PINMUX_PIN(PIN_PB28, 1, 1) +#define PIN_PB28__A17 PINMUX_PIN(PIN_PB28, 2, 1) +#define PIN_PB28__FLEXCOM0_IO0 PINMUX_PIN(PIN_PB28, 3, 1) +#define PIN_PB28__TIOA5 PINMUX_PIN(PIN_PB28, 4, 2) +#define PIN_PB28__ISC_D2 PINMUX_PIN(PIN_PB28, 6, 3) +#define PIN_PB29 61 +#define PIN_PB29__GPIO PINMUX_PIN(PIN_PB29, 0, 0) +#define PIN_PB29__LCDDAT18 PINMUX_PIN(PIN_PB29, 1, 1) +#define PIN_PB29__A18 PINMUX_PIN(PIN_PB29, 2, 1) +#define PIN_PB29__FLEXCOM0_IO1 PINMUX_PIN(PIN_PB29, 3, 1) +#define PIN_PB29__TIOB5 PINMUX_PIN(PIN_PB29, 4, 2) +#define PIN_PB29__ISC_D3 PINMUX_PIN(PIN_PB29, 7, 3) +#define PIN_PB30 62 +#define PIN_PB30__GPIO PINMUX_PIN(PIN_PB30, 0, 0) +#define PIN_PB30__LCDDAT19 PINMUX_PIN(PIN_PB30, 1, 1) +#define PIN_PB30__A19 PINMUX_PIN(PIN_PB30, 2, 1) +#define PIN_PB30__FLEXCOM0_IO2 PINMUX_PIN(PIN_PB30, 3, 1) +#define PIN_PB30__TCLK5 PINMUX_PIN(PIN_PB30, 4, 2) +#define PIN_PB30__ISC_D4 PINMUX_PIN(PIN_PB30, 6, 3) +#define PIN_PB31 63 +#define PIN_PB31__GPIO PINMUX_PIN(PIN_PB31, 0, 0) +#define PIN_PB31__LCDDAT20 PINMUX_PIN(PIN_PB31, 1, 1) +#define PIN_PB31__A20 PINMUX_PIN(PIN_PB31, 2, 1) +#define PIN_PB31__FLEXCOM0_IO3 PINMUX_PIN(PIN_PB31, 3, 1) +#define PIN_PB31__TWD0 PINMUX_PIN(PIN_PB31, 4, 1) +#define PIN_PB31__ISC_D5 PINMUX_PIN(PIN_PB31, 6, 3) +#define PIN_PC0 64 +#define PIN_PC0__GPIO PINMUX_PIN(PIN_PC0, 0, 0) +#define PIN_PC0__LCDDAT21 PINMUX_PIN(PIN_PC0, 1, 1) +#define PIN_PC0__A23 PINMUX_PIN(PIN_PC0, 2, 1) +#define PIN_PC0__FLEXCOM0_IO4 PINMUX_PIN(PIN_PC0, 3, 1) +#define PIN_PC0__TWCK0 PINMUX_PIN(PIN_PC0, 4, 1) +#define PIN_PC0__ISC_D6 PINMUX_PIN(PIN_PC0, 6, 3) +#define PIN_PC1 65 +#define PIN_PC1__GPIO PINMUX_PIN(PIN_PC1, 0, 0) +#define PIN_PC1__LCDDAT22 PINMUX_PIN(PIN_PC1, 1, 1) +#define PIN_PC1__A24 PINMUX_PIN(PIN_PC1, 2, 1) +#define PIN_PC1__CANTX0 PINMUX_PIN(PIN_PC1, 3, 1) +#define PIN_PC1__SPI1_SPCK PINMUX_PIN(PIN_PC1, 4, 1) +#define PIN_PC1__I2SC0_CK PINMUX_PIN(PIN_PC1, 5, 1) +#define PIN_PC1__ISC_D7 PINMUX_PIN(PIN_PC1, 6, 3) +#define PIN_PC2 66 +#define PIN_PC2__GPIO PINMUX_PIN(PIN_PC2, 0, 0) +#define PIN_PC2__LCDDAT23 PINMUX_PIN(PIN_PC2, 1, 1) +#define PIN_PC2__A25 PINMUX_PIN(PIN_PC2, 2, 1) +#define PIN_PC2__CANRX0 PINMUX_PIN(PIN_PC2, 3, 1) +#define PIN_PC2__SPI1_MOSI PINMUX_PIN(PIN_PC2, 4, 1) +#define PIN_PC2__I2SC0_MCK PINMUX_PIN(PIN_PC2, 5, 1) +#define PIN_PC2__ISC_D8 PINMUX_PIN(PIN_PC2, 6, 3) +#define PIN_PC3 67 +#define PIN_PC3__GPIO PINMUX_PIN(PIN_PC3, 0, 0) +#define PIN_PC3__LCDPWM PINMUX_PIN(PIN_PC3, 1, 1) +#define PIN_PC3__NWAIT PINMUX_PIN(PIN_PC3, 2, 1) +#define PIN_PC3__TIOA1 PINMUX_PIN(PIN_PC3, 3, 1) +#define PIN_PC3__SPI1_MISO PINMUX_PIN(PIN_PC3, 4, 1) +#define PIN_PC3__I2SC0_WS PINMUX_PIN(PIN_PC3, 5, 1) +#define PIN_PC3__ISC_D9 PINMUX_PIN(PIN_PC3, 6, 3) +#define PIN_PC4 68 +#define PIN_PC4__GPIO PINMUX_PIN(PIN_PC4, 0, 0) +#define PIN_PC4__LCDDISP PINMUX_PIN(PIN_PC4, 1, 1) +#define PIN_PC4__NWR1_NBS1 PINMUX_PIN(PIN_PC4, 2, 1) +#define PIN_PC4__TIOB1 PINMUX_PIN(PIN_PC4, 3, 1) +#define PIN_PC4__SPI1_NPCS0 PINMUX_PIN(PIN_PC4, 4, 1) +#define PIN_PC4__I2SC0_DI0 PINMUX_PIN(PIN_PC4, 5, 1) +#define PIN_PC4__ISC_PCK PINMUX_PIN(PIN_PC4, 6, 3) +#define PIN_PC5 69 +#define PIN_PC5__GPIO PINMUX_PIN(PIN_PC5, 0, 0) +#define PIN_PC5__LCDVSYNC PINMUX_PIN(PIN_PC5, 1, 1) +#define PIN_PC5__NCS0 PINMUX_PIN(PIN_PC5, 2, 1) +#define PIN_PC5__TCLK1 PINMUX_PIN(PIN_PC5, 3, 1) +#define PIN_PC5__SPI1_NPCS1 PINMUX_PIN(PIN_PC5, 4, 1) +#define PIN_PC5__I2SC0_DO0 PINMUX_PIN(PIN_PC5, 5, 1) +#define PIN_PC5__ISC_VSYNC PINMUX_PIN(PIN_PC5, 6, 3) +#define PIN_PC6 70 +#define PIN_PC6__GPIO PINMUX_PIN(PIN_PC6, 0, 0) +#define PIN_PC6__LCDHSYNC PINMUX_PIN(PIN_PC6, 1, 1) +#define PIN_PC6__NCS1 PINMUX_PIN(PIN_PC6, 2, 1) +#define PIN_PC6__TWD1 PINMUX_PIN(PIN_PC6, 3, 1) +#define PIN_PC6__SPI1_NPCS2 PINMUX_PIN(PIN_PC6, 4, 1) +#define PIN_PC6__ISC_HSYNC PINMUX_PIN(PIN_PC6, 6, 3) +#define PIN_PC7 71 +#define PIN_PC7__GPIO PINMUX_PIN(PIN_PC7, 0, 0) +#define PIN_PC7__LCDPCK PINMUX_PIN(PIN_PC7, 1, 1) +#define PIN_PC7__NCS2 PINMUX_PIN(PIN_PC7, 2, 1) +#define PIN_PC7__TWCK1 PINMUX_PIN(PIN_PC7, 3, 1) +#define PIN_PC7__SPI1_NPCS3 PINMUX_PIN(PIN_PC7, 4, 1) +#define PIN_PC7__URXD1 PINMUX_PIN(PIN_PC7, 5, 2) +#define PIN_PC7__ISC_MCK PINMUX_PIN(PIN_PC7, 6, 3) +#define PIN_PC8 72 +#define PIN_PC8__GPIO PINMUX_PIN(PIN_PC8, 0, 0) +#define PIN_PC8__LCDDEN PINMUX_PIN(PIN_PC8, 1, 1) +#define PIN_PC8__NANDRDY PINMUX_PIN(PIN_PC8, 2, 1) +#define PIN_PC8__FIQ PINMUX_PIN(PIN_PC8, 3, 1) +#define PIN_PC8__PCK0 PINMUX_PIN(PIN_PC8, 4, 3) +#define PIN_PC8__UTXD1 PINMUX_PIN(PIN_PC8, 5, 2) +#define PIN_PC8__ISC_FIELD PINMUX_PIN(PIN_PC8, 6, 3) +#define PIN_PC9 73 +#define PIN_PC9__GPIO PINMUX_PIN(PIN_PC9, 0, 0) +#define PIN_PC9__FIQ PINMUX_PIN(PIN_PC9, 1, 3) +#define PIN_PC9__GTSUCOMP PINMUX_PIN(PIN_PC9, 2, 1) +#define PIN_PC9__ISC_D0 PINMUX_PIN(PIN_PC9, 2, 1) +#define PIN_PC9__TIOA4 PINMUX_PIN(PIN_PC9, 4, 2) +#define PIN_PC10 74 +#define PIN_PC10__GPIO PINMUX_PIN(PIN_PC10, 0, 0) +#define PIN_PC10__LCDDAT2 PINMUX_PIN(PIN_PC10, 1, 2) +#define PIN_PC10__GTXCK PINMUX_PIN(PIN_PC10, 2, 1) +#define PIN_PC10__ISC_D1 PINMUX_PIN(PIN_PC10, 3, 1) +#define PIN_PC10__TIOB4 PINMUX_PIN(PIN_PC10, 4, 2) +#define PIN_PC10__CANTX0 PINMUX_PIN(PIN_PC10, 5, 2) +#define PIN_PC11 75 +#define PIN_PC11__GPIO PINMUX_PIN(PIN_PC11, 0, 0) +#define PIN_PC11__LCDDAT3 PINMUX_PIN(PIN_PC11, 1, 2) +#define PIN_PC11__GTXEN PINMUX_PIN(PIN_PC11, 2, 1) +#define PIN_PC11__ISC_D2 PINMUX_PIN(PIN_PC11, 3, 1) +#define PIN_PC11__TCLK4 PINMUX_PIN(PIN_PC11, 4, 2) +#define PIN_PC11__CANRX0 PINMUX_PIN(PIN_PC11, 5, 2) +#define PIN_PC11__A0_NBS0 PINMUX_PIN(PIN_PC11, 6, 2) +#define PIN_PC12 76 +#define PIN_PC12__GPIO PINMUX_PIN(PIN_PC12, 0, 0) +#define PIN_PC12__LCDDAT4 PINMUX_PIN(PIN_PC12, 1, 2) +#define PIN_PC12__GRXDV PINMUX_PIN(PIN_PC12, 2, 1) +#define PIN_PC12__ISC_D3 PINMUX_PIN(PIN_PC12, 3, 1) +#define PIN_PC12__URXD3 PINMUX_PIN(PIN_PC12, 4, 1) +#define PIN_PC12__TK0 PINMUX_PIN(PIN_PC12, 5, 2) +#define PIN_PC12__A1 PINMUX_PIN(PIN_PC12, 6, 2) +#define PIN_PC13 77 +#define PIN_PC13__GPIO PINMUX_PIN(PIN_PC13, 0, 0) +#define PIN_PC13__LCDDAT5 PINMUX_PIN(PIN_PC13, 1, 2) +#define PIN_PC13__GRXER PINMUX_PIN(PIN_PC13, 2, 1) +#define PIN_PC13__ISC_D4 PINMUX_PIN(PIN_PC13, 3, 1) +#define PIN_PC13__UTXD3 PINMUX_PIN(PIN_PC13, 4, 1) +#define PIN_PC13__TF0 PINMUX_PIN(PIN_PC13, 5, 2) +#define PIN_PC13__A2 PINMUX_PIN(PIN_PC13, 6, 2) +#define PIN_PC14 78 +#define PIN_PC14__GPIO PINMUX_PIN(PIN_PC14, 0, 0) +#define PIN_PC14__LCDDAT6 PINMUX_PIN(PIN_PC14, 1, 2) +#define PIN_PC14__GRX0 PINMUX_PIN(PIN_PC14, 2, 1) +#define PIN_PC14__ISC_D5 PINMUX_PIN(PIN_PC14, 3, 1) +#define PIN_PC14__TDO PINMUX_PIN(PIN_PC14, 5, 2) +#define PIN_PC14__A3 PINMUX_PIN(PIN_PC14, 6, 2) +#define PIN_PC15 79 +#define PIN_PC15__GPIO PINMUX_PIN(PIN_PC15, 0, 0) +#define PIN_PC15__LCDDAT7 PINMUX_PIN(PIN_PC15, 1, 2) +#define PIN_PC15__GRX1 PINMUX_PIN(PIN_PC15, 2, 1) +#define PIN_PC15__ISC_D6 PINMUX_PIN(PIN_PC15, 3, 1) +#define PIN_PC15__RD0 PINMUX_PIN(PIN_PC15, 5, 2) +#define PIN_PC15__A4 PINMUX_PIN(PIN_PC15, 6, 2) +#define PIN_PC16 80 +#define PIN_PC16__GPIO PINMUX_PIN(PIN_PC16, 0, 0) +#define PIN_PC16__LCDDAT10 PINMUX_PIN(PIN_PC16, 1, 2) +#define PIN_PC16__GTX0 PINMUX_PIN(PIN_PC16, 2, 1) +#define PIN_PC16__ISC_D7 PINMUX_PIN(PIN_PC16, 3, 1) +#define PIN_PC16__RK0 PINMUX_PIN(PIN_PC16, 5, 2) +#define PIN_PC16__A5 PINMUX_PIN(PIN_PC16, 6, 2) +#define PIN_PC17 81 +#define PIN_PC17__GPIO PINMUX_PIN(PIN_PC17, 0, 0) +#define PIN_PC17__LCDDAT11 PINMUX_PIN(PIN_PC17, 1, 2) +#define PIN_PC17__GTX1 PINMUX_PIN(PIN_PC17, 2, 1) +#define PIN_PC17__ISC_D8 PINMUX_PIN(PIN_PC17, 3, 1) +#define PIN_PC17__RF0 PINMUX_PIN(PIN_PC17, 5, 2) +#define PIN_PC17__A6 PINMUX_PIN(PIN_PC17, 6, 2) +#define PIN_PC18 82 +#define PIN_PC18__GPIO PINMUX_PIN(PIN_PC18, 0, 0) +#define PIN_PC18__LCDDAT12 PINMUX_PIN(PIN_PC18, 1, 2) +#define PIN_PC18__GMDC PINMUX_PIN(PIN_PC18, 2, 1) +#define PIN_PC18__ISC_D9 PINMUX_PIN(PIN_PC18, 3, 1) +#define PIN_PC18__FLEXCOM3_IO2 PINMUX_PIN(PIN_PC18, 5, 2) +#define PIN_PC18__A7 PINMUX_PIN(PIN_PC18, 6, 2) +#define PIN_PC19 83 +#define PIN_PC19__GPIO PINMUX_PIN(PIN_PC19, 0, 0) +#define PIN_PC19__LCDDAT13 PINMUX_PIN(PIN_PC19, 1, 2) +#define PIN_PC19__GMDIO PINMUX_PIN(PIN_PC19, 2, 1) +#define PIN_PC19__ISC_D10 PINMUX_PIN(PIN_PC19, 3, 1) +#define PIN_PC19__FLEXCOM3_IO1 PINMUX_PIN(PIN_PC19, 5, 2) +#define PIN_PC19__A8 PINMUX_PIN(PIN_PC19, 6, 2) +#define PIN_PC20 84 +#define PIN_PC20__GPIO PINMUX_PIN(PIN_PC20, 0, 0) +#define PIN_PC20__LCDDAT14 PINMUX_PIN(PIN_PC20, 1, 2) +#define PIN_PC20__GRXCK PINMUX_PIN(PIN_PC20, 2, 1) +#define PIN_PC20__ISC_D11 PINMUX_PIN(PIN_PC20, 3, 1) +#define PIN_PC20__FLEXCOM3_IO0 PINMUX_PIN(PIN_PC20, 5, 2) +#define PIN_PC20__A9 PINMUX_PIN(PIN_PC20, 6, 2) +#define PIN_PC21 85 +#define PIN_PC21__GPIO PINMUX_PIN(PIN_PC21, 0, 0) +#define PIN_PC21__LCDDAT15 PINMUX_PIN(PIN_PC21, 1, 2) +#define PIN_PC21__GTXER PINMUX_PIN(PIN_PC21, 2, 1) +#define PIN_PC21__ISC_PCK PINMUX_PIN(PIN_PC21, 3, 1) +#define PIN_PC21__FLEXCOM3_IO3 PINMUX_PIN(PIN_PC21, 5, 2) +#define PIN_PC21__A10 PINMUX_PIN(PIN_PC21, 6, 2) +#define PIN_PC22 86 +#define PIN_PC22__GPIO PINMUX_PIN(PIN_PC22, 0, 0) +#define PIN_PC22__LCDDAT18 PINMUX_PIN(PIN_PC22, 1, 2) +#define PIN_PC22__GCRS PINMUX_PIN(PIN_PC22, 2, 1) +#define PIN_PC22__ISC_VSYNC PINMUX_PIN(PIN_PC22, 3, 1) +#define PIN_PC22__FLEXCOM3_IO4 PINMUX_PIN(PIN_PC22, 5, 2) +#define PIN_PC22__A11 PINMUX_PIN(PIN_PC22, 6, 2) +#define PIN_PC23 87 +#define PIN_PC23__GPIO PINMUX_PIN(PIN_PC23, 0, 0) +#define PIN_PC23__LCDDAT19 PINMUX_PIN(PIN_PC23, 1, 2) +#define PIN_PC23__GCOL PINMUX_PIN(PIN_PC23, 2, 1) +#define PIN_PC23__ISC_HSYNC PINMUX_PIN(PIN_PC23, 3, 1) +#define PIN_PC23__A12 PINMUX_PIN(PIN_PC23, 6, 2) +#define PIN_PC24 88 +#define PIN_PC24__GPIO PINMUX_PIN(PIN_PC24, 0, 0) +#define PIN_PC24__LCDDAT20 PINMUX_PIN(PIN_PC24, 1, 2) +#define PIN_PC24__GRX2 PINMUX_PIN(PIN_PC24, 2, 1) +#define PIN_PC24__ISC_MCK PINMUX_PIN(PIN_PC24, 3, 1) +#define PIN_PC24__A13 PINMUX_PIN(PIN_PC24, 6, 2) +#define PIN_PC25 89 +#define PIN_PC25__GPIO PINMUX_PIN(PIN_PC25, 0, 0) +#define PIN_PC25__LCDDAT21 PINMUX_PIN(PIN_PC25, 1, 2) +#define PIN_PC25__GRX3 PINMUX_PIN(PIN_PC25, 2, 1) +#define PIN_PC25__ISC_FIELD PINMUX_PIN(PIN_PC25, 3, 1) +#define PIN_PC25__A14 PINMUX_PIN(PIN_PC25, 6, 2) +#define PIN_PC26 90 +#define PIN_PC26__GPIO PINMUX_PIN(PIN_PC26, 0, 0) +#define PIN_PC26__LCDDAT22 PINMUX_PIN(PIN_PC26, 1, 2) +#define PIN_PC26__GTX2 PINMUX_PIN(PIN_PC26, 2, 1) +#define PIN_PC26__CANTX1 PINMUX_PIN(PIN_PC26, 4, 1) +#define PIN_PC26__A15 PINMUX_PIN(PIN_PC26, 6, 2) +#define PIN_PC27 91 +#define PIN_PC27__GPIO PINMUX_PIN(PIN_PC27, 0, 0) +#define PIN_PC27__LCDDAT23 PINMUX_PIN(PIN_PC27, 1, 2) +#define PIN_PC27__GTX3 PINMUX_PIN(PIN_PC27, 2, 1) +#define PIN_PC27__PCK1 PINMUX_PIN(PIN_PC27, 3, 2) +#define PIN_PC27__CANRX1 PINMUX_PIN(PIN_PC27, 4, 1) +#define PIN_PC27__TWD0 PINMUX_PIN(PIN_PC27, 5, 2) +#define PIN_PC27__A16 PINMUX_PIN(PIN_PC27, 6, 2) +#define PIN_PC28 92 +#define PIN_PC28__GPIO PINMUX_PIN(PIN_PC28, 0, 0) +#define PIN_PC28__LCDPWM PINMUX_PIN(PIN_PC28, 1, 2) +#define PIN_PC28__FLEXCOM4_IO0 PINMUX_PIN(PIN_PC28, 2, 1) +#define PIN_PC28__PCK2 PINMUX_PIN(PIN_PC28, 3, 2) +#define PIN_PC28__TWCK0 PINMUX_PIN(PIN_PC28, 5, 2) +#define PIN_PC28__A17 PINMUX_PIN(PIN_PC28, 6, 2) +#define PIN_PC29 93 +#define PIN_PC29__GPIO PINMUX_PIN(PIN_PC29, 0, 0) +#define PIN_PC29__LCDDISP PINMUX_PIN(PIN_PC29, 1, 2) +#define PIN_PC29__FLEXCOM4_IO1 PINMUX_PIN(PIN_PC29, 2, 1) +#define PIN_PC29__A18 PINMUX_PIN(PIN_PC29, 6, 2) +#define PIN_PC30 94 +#define PIN_PC30__GPIO PINMUX_PIN(PIN_PC30, 0, 0) +#define PIN_PC30__LCDVSYNC PINMUX_PIN(PIN_PC30, 1, 2) +#define PIN_PC30__FLEXCOM4_IO2 PINMUX_PIN(PIN_PC30, 2, 1) +#define PIN_PC30__A19 PINMUX_PIN(PIN_PC30, 6, 2) +#define PIN_PC31 95 +#define PIN_PC31__GPIO PINMUX_PIN(PIN_PC31, 0, 0) +#define PIN_PC31__LCDHSYNC PINMUX_PIN(PIN_PC31, 1, 2) +#define PIN_PC31__FLEXCOM4_IO3 PINMUX_PIN(PIN_PC31, 2, 1) +#define PIN_PC31__URXD3 PINMUX_PIN(PIN_PC31, 3, 2) +#define PIN_PC31__A20 PINMUX_PIN(PIN_PC31, 6, 2) +#define PIN_PD0 96 +#define PIN_PD0__GPIO PINMUX_PIN(PIN_PD0, 0, 0) +#define PIN_PD0__LCDPCK PINMUX_PIN(PIN_PD0, 1, 2) +#define PIN_PD0__FLEXCOM4_IO4 PINMUX_PIN(PIN_PD0, 2, 1) +#define PIN_PD0__UTXD3 PINMUX_PIN(PIN_PD0, 3, 2) +#define PIN_PD0__GTSUCOMP PINMUX_PIN(PIN_PD0, 4, 2) +#define PIN_PD0__A23 PINMUX_PIN(PIN_PD0, 6, 2) +#define PIN_PD1 97 +#define PIN_PD1__GPIO PINMUX_PIN(PIN_PD1, 0, 0) +#define PIN_PD1__LCDDEN PINMUX_PIN(PIN_PD1, 1, 2) +#define PIN_PD1__GRXCK PINMUX_PIN(PIN_PD1, 4, 2) +#define PIN_PD1__A24 PINMUX_PIN(PIN_PD1, 6, 2) +#define PIN_PD2 98 +#define PIN_PD2__GPIO PINMUX_PIN(PIN_PD2, 0, 0) +#define PIN_PD2__URXD1 PINMUX_PIN(PIN_PD2, 1, 1) +#define PIN_PD2__GTXER PINMUX_PIN(PIN_PD2, 4, 2) +#define PIN_PD2__ISC_MCK PINMUX_PIN(PIN_PD2, 5, 2) +#define PIN_PD2__A25 PINMUX_PIN(PIN_PD2, 6, 2) +#define PIN_PD3 99 +#define PIN_PD3__GPIO PINMUX_PIN(PIN_PD3, 0, 0) +#define PIN_PD3__UTXD1 PINMUX_PIN(PIN_PD3, 1, 1) +#define PIN_PD3__FIQ PINMUX_PIN(PIN_PD3, 2, 2) +#define PIN_PD3__GCRS PINMUX_PIN(PIN_PD3, 4, 2) +#define PIN_PD3__ISC_D11 PINMUX_PIN(PIN_PD3, 5, 2) +#define PIN_PD3__NWAIT PINMUX_PIN(PIN_PD3, 6, 2) +#define PIN_PD4 100 +#define PIN_PD4__GPIO PINMUX_PIN(PIN_PD4, 0, 0) +#define PIN_PD4__TWD1 PINMUX_PIN(PIN_PD4, 1, 2) +#define PIN_PD4__URXD2 PINMUX_PIN(PIN_PD4, 2, 1) +#define PIN_PD4__GCOL PINMUX_PIN(PIN_PD4, 4, 2) +#define PIN_PD4__ISC_D10 PINMUX_PIN(PIN_PD4, 5, 2) +#define PIN_PD4__NCS0 PINMUX_PIN(PIN_PD4, 6, 2) +#define PIN_PD5 101 +#define PIN_PD5__GPIO PINMUX_PIN(PIN_PD5, 0, 0) +#define PIN_PD5__TWCK1 PINMUX_PIN(PIN_PD5, 1, 2) +#define PIN_PD5__UTXD2 PINMUX_PIN(PIN_PD5, 2, 1) +#define PIN_PD5__GRX2 PINMUX_PIN(PIN_PD5, 4, 2) +#define PIN_PD5__ISC_D9 PINMUX_PIN(PIN_PD5, 5, 2) +#define PIN_PD5__NCS1 PINMUX_PIN(PIN_PD5, 6, 2) +#define PIN_PD6 102 +#define PIN_PD6__GPIO PINMUX_PIN(PIN_PD6, 0, 0) +#define PIN_PD6__TCK PINMUX_PIN(PIN_PD6, 1, 2) +#define PIN_PD6__PCK1 PINMUX_PIN(PIN_PD6, 2, 1) +#define PIN_PD6__GRX3 PINMUX_PIN(PIN_PD6, 4, 2) +#define PIN_PD6__ISC_D8 PINMUX_PIN(PIN_PD6, 5, 2) +#define PIN_PD6__NCS2 PINMUX_PIN(PIN_PD6, 6, 2) +#define PIN_PD7 103 +#define PIN_PD7__GPIO PINMUX_PIN(PIN_PD7, 0, 0) +#define PIN_PD7__TDI PINMUX_PIN(PIN_PD7, 1, 2) +#define PIN_PD7__UTMI_RXVAL PINMUX_PIN(PIN_PD7, 3, 1) +#define PIN_PD7__GTX2 PINMUX_PIN(PIN_PD7, 4, 2) +#define PIN_PD7__ISC_D0 PINMUX_PIN(PIN_PD7, 5, 2) +#define PIN_PD7__NWR1_NBS1 PINMUX_PIN(PIN_PD7, 6, 2) +#define PIN_PD8 104 +#define PIN_PD8__GPIO PINMUX_PIN(PIN_PD8, 0, 0) +#define PIN_PD8__TDO PINMUX_PIN(PIN_PD8, 1, 2) +#define PIN_PD8__UTMI_RXERR PINMUX_PIN(PIN_PD8, 3, 1) +#define PIN_PD8__GTX3 PINMUX_PIN(PIN_PD8, 4, 2) +#define PIN_PD8__ISC_D1 PINMUX_PIN(PIN_PD8, 5, 2) +#define PIN_PD8__NANDRDY PINMUX_PIN(PIN_PD8, 6, 2) +#define PIN_PD9 105 +#define PIN_PD9__GPIO PINMUX_PIN(PIN_PD9, 0, 0) +#define PIN_PD9__TMS PINMUX_PIN(PIN_PD9, 1, 2) +#define PIN_PD9__UTMI_RXACT PINMUX_PIN(PIN_PD9, 3, 1) +#define PIN_PD9__GTXCK PINMUX_PIN(PIN_PD9, 4, 2) +#define PIN_PD9__ISC_D2 PINMUX_PIN(PIN_PD9, 5, 2) +#define PIN_PD10 106 +#define PIN_PD10__GPIO PINMUX_PIN(PIN_PD10, 0, 0) +#define PIN_PD10__NTRST PINMUX_PIN(PIN_PD10, 1, 2) +#define PIN_PD10__UTMI_HDIS PINMUX_PIN(PIN_PD10, 3, 1) +#define PIN_PD10__GTXEN PINMUX_PIN(PIN_PD10, 4, 2) +#define PIN_PD10__ISC_D3 PINMUX_PIN(PIN_PD10, 5, 2) +#define PIN_PD11 107 +#define PIN_PD11__GPIO PINMUX_PIN(PIN_PD11, 0, 0) +#define PIN_PD11__TIOA1 PINMUX_PIN(PIN_PD11, 1, 3) +#define PIN_PD11__PCK2 PINMUX_PIN(PIN_PD11, 2, 2) +#define PIN_PD11__UTMI_LS0 PINMUX_PIN(PIN_PD11, 3, 1) +#define PIN_PD11__GRXDV PINMUX_PIN(PIN_PD11, 4, 2) +#define PIN_PD11__ISC_D4 PINMUX_PIN(PIN_PD11, 5, 2) +#define PIN_PD11__ISC_MCK PINMUX_PIN(PIN_PD11, 7, 4) +#define PIN_PD12 108 +#define PIN_PD12__GPIO PINMUX_PIN(PIN_PD12, 0, 0) +#define PIN_PD12__TIOB1 PINMUX_PIN(PIN_PD12, 1, 3) +#define PIN_PD12__FLEXCOM4_IO0 PINMUX_PIN(PIN_PD12, 2, 2) +#define PIN_PD12__UTMI_LS1 PINMUX_PIN(PIN_PD12, 3, 1) +#define PIN_PD12__GRXER PINMUX_PIN(PIN_PD12, 4, 2) +#define PIN_PD12__ISC_D5 PINMUX_PIN(PIN_PD12, 5, 2) +#define PIN_PD12__ISC_D4 PINMUX_PIN(PIN_PD12, 6, 4) +#define PIN_PD13 109 +#define PIN_PD13__GPIO PINMUX_PIN(PIN_PD13, 0, 0) +#define PIN_PD13__TCLK1 PINMUX_PIN(PIN_PD13, 1, 3) +#define PIN_PD13__FLEXCOM4_IO1 PINMUX_PIN(PIN_PD13, 2, 2) +#define PIN_PD13__UTMI_CDRPCSEL0 PINMUX_PIN(PIN_PD13, 3, 1) +#define PIN_PD13__GRX0 PINMUX_PIN(PIN_PD13, 4, 2) +#define PIN_PD13__ISC_D6 PINMUX_PIN(PIN_PD13, 5, 2) +#define PIN_PD13__ISC_D5 PINMUX_PIN(PIN_PD13, 6, 4) +#define PIN_PD14 110 +#define PIN_PD14__GPIO PINMUX_PIN(PIN_PD14, 0, 0) +#define PIN_PD14__TCK PINMUX_PIN(PIN_PD14, 1, 1) +#define PIN_PD14__FLEXCOM4_IO2 PINMUX_PIN(PIN_PD14, 2, 2) +#define PIN_PD14__UTMI_CDRPCSEL1 PINMUX_PIN(PIN_PD14, 3, 1) +#define PIN_PD14__GRX1 PINMUX_PIN(PIN_PD14, 4, 2) +#define PIN_PD14__ISC_D7 PINMUX_PIN(PIN_PD14, 5, 2) +#define PIN_PD14__ISC_D6 PINMUX_PIN(PIN_PD14, 6, 4) +#define PIN_PD15 111 +#define PIN_PD15__GPIO PINMUX_PIN(PIN_PD15, 0, 0) +#define PIN_PD15__TDI PINMUX_PIN(PIN_PD15, 1, 1) +#define PIN_PD15__FLEXCOM4_IO3 PINMUX_PIN(PIN_PD15, 2, 2) +#define PIN_PD15__UTMI_CDRCPDIVEN PINMUX_PIN(PIN_PD15, 3, 1) +#define PIN_PD15__GTX0 PINMUX_PIN(PIN_PD15, 4, 2) +#define PIN_PD15__ISC_PCK PINMUX_PIN(PIN_PD15, 5, 2) +#define PIN_PD15__ISC_D7 PINMUX_PIN(PIN_PD15, 6, 4) +#define PIN_PD16 112 +#define PIN_PD16__GPIO PINMUX_PIN(PIN_PD16, 0, 0) +#define PIN_PD16__TDO PINMUX_PIN(PIN_PD16, 1, 1) +#define PIN_PD16__FLEXCOM4_IO4 PINMUX_PIN(PIN_PD16, 2, 2) +#define PIN_PD16__UTMI_CDRBISTEN PINMUX_PIN(PIN_PD16, 3, 1) +#define PIN_PD16__GTX1 PINMUX_PIN(PIN_PD16, 4, 2) +#define PIN_PD16__ISC_VSYNC PINMUX_PIN(PIN_PD16, 5, 2) +#define PIN_PD16__ISC_D8 PINMUX_PIN(PIN_PD16, 6, 4) +#define PIN_PD17 113 +#define PIN_PD17__GPIO PINMUX_PIN(PIN_PD17, 0, 0) +#define PIN_PD17__TMS PINMUX_PIN(PIN_PD17, 1, 1) +#define PIN_PD17__UTMI_CDRCPSELDIV PINMUX_PIN(PIN_PD17, 3, 1) +#define PIN_PD17__GMDC PINMUX_PIN(PIN_PD17, 4, 2) +#define PIN_PD17__ISC_HSYNC PINMUX_PIN(PIN_PD17, 5, 2) +#define PIN_PD17__ISC_D9 PINMUX_PIN(PIN_PD17, 6, 4) +#define PIN_PD18 114 +#define PIN_PD18__GPIO PINMUX_PIN(PIN_PD18, 0, 0) +#define PIN_PD18__NTRST PINMUX_PIN(PIN_PD18, 1, 1) +#define PIN_PD18__GMDIO PINMUX_PIN(PIN_PD18, 4, 2) +#define PIN_PD18__ISC_FIELD PINMUX_PIN(PIN_PD18, 5, 2) +#define PIN_PD18__ISC_D10 PINMUX_PIN(PIN_PD18, 6, 4) +#define PIN_PD19 115 +#define PIN_PD19__GPIO PINMUX_PIN(PIN_PD19, 0, 0) +#define PIN_PD19__PCK0 PINMUX_PIN(PIN_PD19, 1, 1) +#define PIN_PD19__TWD1 PINMUX_PIN(PIN_PD19, 2, 3) +#define PIN_PD19__URXD2 PINMUX_PIN(PIN_PD19, 3, 3) +#define PIN_PD19__I2SC0_CK PINMUX_PIN(PIN_PD19, 5, 2) +#define PIN_PD19__ISC_D11 PINMUX_PIN(PIN_PD19, 6, 4) +#define PIN_PD20 116 +#define PIN_PD20__GPIO PINMUX_PIN(PIN_PD20, 0, 0) +#define PIN_PD20__TIOA2 PINMUX_PIN(PIN_PD20, 1, 3) +#define PIN_PD20__TWCK1 PINMUX_PIN(PIN_PD20, 2, 3) +#define PIN_PD20__UTXD2 PINMUX_PIN(PIN_PD20, 3, 3) +#define PIN_PD20__I2SC0_MCK PINMUX_PIN(PIN_PD20, 5, 2) +#define PIN_PD20__ISC_PCK PINMUX_PIN(PIN_PD20, 6, 4) +#define PIN_PD21 117 +#define PIN_PD21__GPIO PINMUX_PIN(PIN_PD21, 0, 0) +#define PIN_PD21__TIOB2 PINMUX_PIN(PIN_PD21, 1, 3) +#define PIN_PD21__TWD0 PINMUX_PIN(PIN_PD21, 2, 4) +#define PIN_PD21__FLEXCOM4_IO0 PINMUX_PIN(PIN_PD21, 3, 3) +#define PIN_PD21__I2SC0_WS PINMUX_PIN(PIN_PD21, 5, 2) +#define PIN_PD21__ISC_VSYNC PINMUX_PIN(PIN_PD21, 6, 4) +#define PIN_PD22 118 +#define PIN_PD22__GPIO PINMUX_PIN(PIN_PD22, 0, 0) +#define PIN_PD22__TCLK2 PINMUX_PIN(PIN_PD22, 1, 3) +#define PIN_PD22__TWCK0 PINMUX_PIN(PIN_PD22, 2, 4) +#define PIN_PD22__FLEXCOM4_IO1 PINMUX_PIN(PIN_PD22, 3, 3) +#define PIN_PD22__I2SC0_DI0 PINMUX_PIN(PIN_PD22, 5, 2) +#define PIN_PD22__ISC_HSYNC PINMUX_PIN(PIN_PD22, 6, 4) +#define PIN_PD23 119 +#define PIN_PD23__GPIO PINMUX_PIN(PIN_PD23, 0, 0) +#define PIN_PD23__URXD2 PINMUX_PIN(PIN_PD23, 1, 2) +#define PIN_PD23__FLEXCOM4_IO2 PINMUX_PIN(PIN_PD23, 3, 3) +#define PIN_PD23__I2SC0_DO0 PINMUX_PIN(PIN_PD23, 5, 2) +#define PIN_PD23__ISC_FIELD PINMUX_PIN(PIN_PD23, 6, 4) +#define PIN_PD24 120 +#define PIN_PD24__GPIO PINMUX_PIN(PIN_PD24, 0, 0) +#define PIN_PD24__UTXD2 PINMUX_PIN(PIN_PD23, 1, 2) +#define PIN_PD24__FLEXCOM4_IO3 PINMUX_PIN(PIN_PD23, 3, 3) +#define PIN_PD25 121 +#define PIN_PD25__GPIO PINMUX_PIN(PIN_PD25, 0, 0) +#define PIN_PD25__SPI1_SPCK PINMUX_PIN(PIN_PD25, 1, 3) +#define PIN_PD25__FLEXCOM4_IO4 PINMUX_PIN(PIN_PD25, 3, 3) +#define PIN_PD26 122 +#define PIN_PD26__GPIO PINMUX_PIN(PIN_PD26, 0, 0) +#define PIN_PD26__SPI1_MOSI PINMUX_PIN(PIN_PD26, 1, 3) +#define PIN_PD26__FLEXCOM2_IO0 PINMUX_PIN(PIN_PD26, 3, 2) +#define PIN_PD27 123 +#define PIN_PD27__GPIO PINMUX_PIN(PIN_PD27, 0, 0) +#define PIN_PD27__SPI1_MISO PINMUX_PIN(PIN_PD27, 1, 3) +#define PIN_PD27__TCK PINMUX_PIN(PIN_PD27, 2, 3) +#define PIN_PD27__FLEXCOM2_IO1 PINMUX_PIN(PIN_PD27, 3, 2) +#define PIN_PD28 124 +#define PIN_PD28__GPIO PINMUX_PIN(PIN_PD28, 0, 0) +#define PIN_PD28__SPI1_NPCS0 PINMUX_PIN(PIN_PD28, 1, 3) +#define PIN_PD28__TCI PINMUX_PIN(PIN_PD28, 2, 3) +#define PIN_PD28__FLEXCOM2_IO2 PINMUX_PIN(PIN_PD28, 3, 2) +#define PIN_PD29 125 +#define PIN_PD29__GPIO PINMUX_PIN(PIN_PD29, 0, 0) +#define PIN_PD29__SPI1_NPCS1 PINMUX_PIN(PIN_PD29, 1, 3) +#define PIN_PD29__TDO PINMUX_PIN(PIN_PD29, 2, 3) +#define PIN_PD29__FLEXCOM2_IO3 PINMUX_PIN(PIN_PD29, 3, 2) +#define PIN_PD29__TIOA3 PINMUX_PIN(PIN_PD29, 4, 3) +#define PIN_PD29__TWD0 PINMUX_PIN(PIN_PD29, 5, 3) +#define PIN_PD30 126 +#define PIN_PD30__GPIO PINMUX_PIN(PIN_PD30, 0, 0) +#define PIN_PD30__SPI1_NPCS2 PINMUX_PIN(PIN_PD30, 1, 3) +#define PIN_PD30__TMS PINMUX_PIN(PIN_PD30, 2, 3) +#define PIN_PD30__FLEXCOM2_IO4 PINMUX_PIN(PIN_PD30, 3, 2) +#define PIN_PD30__TIOB3 PINMUX_PIN(PIN_PD30, 4, 3) +#define PIN_PD30__TWCK0 PINMUX_PIN(PIN_PD30, 5, 3) +#define PIN_PD31 127 +#define PIN_PD31__GPIO PINMUX_PIN(PIN_PD31, 0, 0) +#define PIN_PD31__ADTRG PINMUX_PIN(PIN_PD31, 1, 1) +#define PIN_PD31__NTRST PINMUX_PIN(PIN_PD31, 2, 3) +#define PIN_PD31__IRQ PINMUX_PIN(PIN_PD31, 3, 4) +#define PIN_PD31__TCLK3 PINMUX_PIN(PIN_PD31, 4, 3) +#define PIN_PD31__PCK0 PINMUX_PIN(PIN_PD31, 5, 2) diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi index cc05cde0f9a4..4dfca8fc49b3 100644 --- a/arch/arm/boot/dts/sama5d2.dtsi +++ b/arch/arm/boot/dts/sama5d2.dtsi @@ -263,6 +263,24 @@ cache-level = <2>; }; + sdmmc0: sdio-host@a0000000 { + compatible = "atmel,sama5d2-sdhci"; + reg = <0xa0000000 0x300>; + interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&sdmmc0_hclk>, <&sdmmc0_gclk>, <&main>; + clock-names = "hclock", "multclk", "baseclk"; + status = "disabled"; + }; + + sdmmc1: sdio-host@b0000000 { + compatible = "atmel,sama5d2-sdhci"; + reg = <0xb0000000 0x300>; + interrupts = <32 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&sdmmc1_hclk>, <&sdmmc1_gclk>, <&main>; + clock-names = "hclock", "multclk", "baseclk"; + status = "disabled"; + }; + apb { compatible = "simple-bus"; #address-cells = <1>; @@ -286,7 +304,7 @@ }; pmc: pmc@f0014000 { - compatible = "atmel,sama5d2-pmc"; + compatible = "atmel,sama5d2-pmc", "syscon"; reg = <0xf0014000 0x160>; interrupts = <74 IRQ_TYPE_LEVEL_HIGH 7>; interrupt-controller; @@ -619,6 +637,18 @@ atmel,clk-output-range = <0 83000000>; }; + i2s0_clk: i2s0_clk { + #clock-cells = <0>; + reg = <54>; + atmel,clk-output-range = <0 83000000>; + }; + + i2s1_clk: i2s1_clk { + #clock-cells = <0>; + reg = <55>; + atmel,clk-output-range = <0 83000000>; + }; + classd_clk: classd_clk { #clock-cells = <0>; reg = <59>; @@ -697,6 +727,52 @@ reg = <53>; }; }; + + gck { + compatible = "atmel,sama5d2-clk-generated"; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <&pmc>; + clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>; + + sdmmc0_gclk: sdmmc0_gclk { + #clock-cells = <0>; + reg = <31>; + }; + + sdmmc1_gclk: sdmmc1_gclk { + #clock-cells = <0>; + reg = <32>; + }; + + tcb0_gclk: tcb0_gclk { + #clock-cells = <0>; + reg = <35>; + atmel,clk-output-range = <0 83000000>; + }; + + tcb1_gclk: tcb1_gclk { + #clock-cells = <0>; + reg = <36>; + atmel,clk-output-range = <0 83000000>; + }; + + pwm_gclk: pwm_gclk { + #clock-cells = <0>; + reg = <38>; + atmel,clk-output-range = <0 83000000>; + }; + + i2s0_gclk: i2s0_gclk { + #clock-cells = <0>; + reg = <54>; + }; + + i2s1_gclk: i2s1_gclk { + #clock-cells = <0>; + reg = <55>; + }; + }; }; sha@f0028000 { @@ -709,7 +785,7 @@ dma-names = "tx"; clocks = <&sha_clk>; clock-names = "sha_clk"; - status = "disabled"; + status = "okay"; }; aes@f002c000 { @@ -725,7 +801,7 @@ dma-names = "tx", "rx"; clocks = <&aes_clk>; clock-names = "aes_clk"; - status = "disabled"; + status = "okay"; }; spi0: spi@f8000000 { @@ -820,6 +896,32 @@ status = "disabled"; }; + flx0: flexcom@f8034000 { + compatible = "atmel,sama5d2-flexcom"; + reg = <0xf8034000 0x200>; + clocks = <&flx0_clk>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0xf8034000 0x800>; + status = "disabled"; + }; + + flx1: flexcom@f8038000 { + compatible = "atmel,sama5d2-flexcom"; + reg = <0xf8038000 0x200>; + clocks = <&flx1_clk>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0xf8038000 0x800>; + status = "disabled"; + }; + + rstc@f8048000 { + compatible = "atmel,sama5d3-rstc"; + reg = <0xf8048000 0x10>; + clocks = <&clk32k>; + }; + pit: timer@f8048030 { compatible = "atmel,at91sam9260-pit"; reg = <0xf8048030 0x10>; @@ -897,6 +999,36 @@ status = "disabled"; }; + flx2: flexcom@fc010000 { + compatible = "atmel,sama5d2-flexcom"; + reg = <0xfc010000 0x200>; + clocks = <&flx2_clk>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0xfc010000 0x800>; + status = "disabled"; + }; + + flx3: flexcom@fc014000 { + compatible = "atmel,sama5d2-flexcom"; + reg = <0xfc014000 0x200>; + clocks = <&flx3_clk>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0xfc014000 0x800>; + status = "disabled"; + }; + + flx4: flexcom@fc018000 { + compatible = "atmel,sama5d2-flexcom"; + reg = <0xfc018000 0x200>; + clocks = <&flx4_clk>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0xfc018000 0x800>; + status = "disabled"; + }; + aic: interrupt-controller@fc020000 { #interrupt-cells = <3>; compatible = "atmel,sama5d2-aic"; @@ -935,6 +1067,22 @@ #gpio-cells = <2>; clocks = <&pioA_clk>; }; + + tdes@fc044000 { + compatible = "atmel,at91sam9g46-tdes"; + reg = <0xfc044000 0x100>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 0>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(28))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(29))>; + dma-names = "tx", "rx"; + clocks = <&tdes_clk>; + clock-names = "tdes_clk"; + status = "okay"; + }; }; }; }; diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi index 7fa276515f11..a53279160f98 100644 --- a/arch/arm/boot/dts/sama5d3.dtsi +++ b/arch/arm/boot/dts/sama5d3.dtsi @@ -75,7 +75,7 @@ adc_op_clk: adc_op_clk{ compatible = "fixed-clock"; #clock-cells = <0>; - clock-frequency = <20000000>; + clock-frequency = <1000000>; }; }; @@ -322,6 +322,7 @@ atmel,adc-use-external-triggers; atmel,adc-vref = <3000>; atmel,adc-res = <10 12>; + atmel,adc-sample-hold-time = <11>; atmel,adc-res-names = "lowres", "highres"; status = "disabled"; @@ -906,7 +907,7 @@ }; pmc: pmc@fffffc00 { - compatible = "atmel,sama5d3-pmc"; + compatible = "atmel,sama5d3-pmc", "syscon"; reg = <0xfffffc00 0x120>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; interrupt-controller; diff --git a/arch/arm/boot/dts/sama5d3_mci2.dtsi b/arch/arm/boot/dts/sama5d3_mci2.dtsi index 026b252f09b3..e21099a1aef9 100644 --- a/arch/arm/boot/dts/sama5d3_mci2.dtsi +++ b/arch/arm/boot/dts/sama5d3_mci2.dtsi @@ -24,9 +24,9 @@ }; pinctrl_mmc2_dat1_3: mmc2_dat1_3 { atmel,pins = - <AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC12 periph A MCI2_DA1 with pullup, conflicts with TIOA1 */ - AT91_PIOC 13 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC13 periph A MCI2_DA2 with pullup, conflicts with TIOB1 */ - AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PC14 periph A MCI2_DA3 with pullup, conflicts with TCLK1 */ + <AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PC12 periph A MCI2_DA1 with pullup, conflicts with TIOA1 */ + AT91_PIOC 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PC13 periph A MCI2_DA2 with pullup, conflicts with TIOB1 */ + AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PC14 periph A MCI2_DA3 with pullup, conflicts with TCLK1 */ }; }; }; diff --git a/arch/arm/boot/dts/sama5d3xmb.dtsi b/arch/arm/boot/dts/sama5d3xmb.dtsi index 83bee7a3a617..89010422812d 100644 --- a/arch/arm/boot/dts/sama5d3xmb.dtsi +++ b/arch/arm/boot/dts/sama5d3xmb.dtsi @@ -87,6 +87,8 @@ isi_0: endpoint { remote-endpoint = <&ov2640_0>; bus-width = <8>; + vsync-active = <1>; + hsync-active = <1>; }; }; }; diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi index 8d1de29e8da1..15bbaf690047 100644 --- a/arch/arm/boot/dts/sama5d4.dtsi +++ b/arch/arm/boot/dts/sama5d4.dtsi @@ -386,7 +386,7 @@ }; pmc: pmc@f0018000 { - compatible = "atmel,sama5d3-pmc"; + compatible = "atmel,sama5d3-pmc", "syscon"; reg = <0xf0018000 0x120>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; interrupt-controller; @@ -939,11 +939,11 @@ reg = <0xf8018000 0x4000>; interrupts = <33 IRQ_TYPE_LEVEL_HIGH 6>; dmas = <&dma1 - (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) - AT91_XDMAC_DT_PERID(4)>, + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(4))>, <&dma1 - (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) - AT91_XDMAC_DT_PERID(5)>; + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(5))>; dma-names = "tx", "rx"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c1>; @@ -1189,6 +1189,19 @@ clock-names = "t0_clk", "slow_clk"; }; + macb1: ethernet@fc028000 { + compatible = "atmel,sama5d4-gem"; + reg = <0xfc028000 0x100>; + interrupts = <55 IRQ_TYPE_LEVEL_HIGH 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_macb1_rmii>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&macb1_clk>, <&macb1_clk>; + clock-names = "hclk", "pclk"; + status = "disabled"; + }; + adc0: adc@fc034000 { compatible = "atmel,at91sam9x5-adc"; reg = <0xfc034000 0x100>; @@ -1238,7 +1251,7 @@ dma-names = "tx", "rx"; clocks = <&aes_clk>; clock-names = "aes_clk"; - status = "disabled"; + status = "okay"; }; tdes@fc04c000 { @@ -1252,7 +1265,7 @@ dma-names = "tx", "rx"; clocks = <&tdes_clk>; clock-names = "tdes_clk"; - status = "disabled"; + status = "okay"; }; sha@fc050000 { @@ -1264,7 +1277,7 @@ dma-names = "tx"; clocks = <&sha_clk>; clock-names = "sha_clk"; - status = "disabled"; + status = "okay"; }; rstc@fc068600 { @@ -1350,7 +1363,7 @@ 0xffffffff 0x3ffcfe7c 0x1c010101 /* pioA */ 0x7fffffff 0xfffccc3a 0x3f00cc3a /* pioB */ 0xffffffff 0x3ff83fff 0xff00ffff /* pioC */ - 0x00000000 0x00000000 0x00000000 /* pioD */ + 0x0003ff00 0x8002a800 0x00000000 /* pioD */ 0xffffffff 0x7fffffff 0x76fff1bf /* pioE */ >; @@ -1396,7 +1409,6 @@ interrupt-controller; #interrupt-cells = <2>; clocks = <&pioD_clk>; - status = "disabled"; }; pioE: gpio@fc06d000 { @@ -1636,6 +1648,23 @@ }; }; + macb1 { + pinctrl_macb1_rmii: macb1_rmii-0 { + atmel,pins = + <AT91_PIOA 14 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_TX0 */ + AT91_PIOA 15 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_TX1 */ + AT91_PIOA 12 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_RX0 */ + AT91_PIOA 13 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_RX1 */ + AT91_PIOA 10 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_RXDV */ + AT91_PIOA 11 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_RXER */ + AT91_PIOA 4 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_TXEN */ + AT91_PIOA 2 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_TXCK */ + AT91_PIOA 22 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_MDC */ + AT91_PIOA 23 AT91_PERIPH_B AT91_PINCTRL_NONE /* G1_MDIO */ + >; + }; + }; + mmc0 { pinctrl_mmc0_clk_cmd_dat0: mmc0_clk_cmd_dat0 { atmel,pins = diff --git a/arch/arm/boot/dts/sh73a0-kzm9g.dts b/arch/arm/boot/dts/sh73a0-kzm9g.dts index 24b4cd24dceb..7fc5602810ad 100644 --- a/arch/arm/boot/dts/sh73a0-kzm9g.dts +++ b/arch/arm/boot/dts/sh73a0-kzm9g.dts @@ -206,7 +206,7 @@ }; accelerometer@1d { - compatible = "adi,adxl34x"; + compatible = "adi,adxl345"; reg = <0x1d>; interrupt-parent = <&irqpin3>; interrupts = <2 IRQ_TYPE_LEVEL_HIGH>, diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi index 314e589cfa00..39c470e291f9 100644 --- a/arch/arm/boot/dts/socfpga.dtsi +++ b/arch/arm/boot/dts/socfpga.dtsi @@ -513,6 +513,13 @@ }; }; + fpgamgr0: fpgamgr@ff706000 { + compatible = "altr,socfpga-fpga-mgr"; + reg = <0xff706000 0x1000 + 0xffb90000 0x1000>; + interrupts = <0 175 4>; + }; + gmac0: ethernet@ff700000 { compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac"; altr,sysmgr-syscon = <&sysmgr 0x60 0>; @@ -549,46 +556,6 @@ status = "disabled"; }; - i2c0: i2c@ffc04000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "snps,designware-i2c"; - reg = <0xffc04000 0x1000>; - clocks = <&l4_sp_clk>; - interrupts = <0 158 0x4>; - status = "disabled"; - }; - - i2c1: i2c@ffc05000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "snps,designware-i2c"; - reg = <0xffc05000 0x1000>; - clocks = <&l4_sp_clk>; - interrupts = <0 159 0x4>; - status = "disabled"; - }; - - i2c2: i2c@ffc06000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "snps,designware-i2c"; - reg = <0xffc06000 0x1000>; - clocks = <&l4_sp_clk>; - interrupts = <0 160 0x4>; - status = "disabled"; - }; - - i2c3: i2c@ffc07000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "snps,designware-i2c"; - reg = <0xffc07000 0x1000>; - clocks = <&l4_sp_clk>; - interrupts = <0 161 0x4>; - status = "disabled"; - }; - gpio0: gpio@ff708000 { #address-cells = <1>; #size-cells = <0>; @@ -649,15 +616,44 @@ }; }; - sdr: sdr@ffc25000 { - compatible = "syscon"; - reg = <0xffc25000 0x1000>; + i2c0: i2c@ffc04000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc04000 0x1000>; + clocks = <&l4_sp_clk>; + interrupts = <0 158 0x4>; + status = "disabled"; }; - sdramedac { - compatible = "altr,sdram-edac"; - altr,sdr-syscon = <&sdr>; - interrupts = <0 39 4>; + i2c1: i2c@ffc05000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc05000 0x1000>; + clocks = <&l4_sp_clk>; + interrupts = <0 159 0x4>; + status = "disabled"; + }; + + i2c2: i2c@ffc06000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc06000 0x1000>; + clocks = <&l4_sp_clk>; + interrupts = <0 160 0x4>; + status = "disabled"; + }; + + i2c3: i2c@ffc07000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc07000 0x1000>; + clocks = <&l4_sp_clk>; + interrupts = <0 161 0x4>; + status = "disabled"; }; L2: l2-cache@fffef000 { @@ -688,6 +684,29 @@ reg = <0xffff0000 0x10000>; }; + rst: rstmgr@ffd05000 { + #reset-cells = <1>; + compatible = "altr,rst-mgr"; + reg = <0xffd05000 0x1000>; + altr,modrst-offset = <0x10>; + }; + + scu: snoop-control-unit@fffec000 { + compatible = "arm,cortex-a9-scu"; + reg = <0xfffec000 0x100>; + }; + + sdr: sdr@ffc25000 { + compatible = "syscon"; + reg = <0xffc25000 0x1000>; + }; + + sdramedac { + compatible = "altr,sdram-edac"; + altr,sdr-syscon = <&sdr>; + interrupts = <0 39 4>; + }; + spi0: spi@fff00000 { compatible = "snps,dw-apb-ssi"; #address-cells = <1>; @@ -699,11 +718,6 @@ status = "disabled"; }; - scu: snoop-control-unit@fffec000 { - compatible = "arm,cortex-a9-scu"; - reg = <0xfffec000 0x100>; - }; - spi1: spi@fff01000 { compatible = "snps,dw-apb-ssi"; #address-cells = <1>; @@ -715,6 +729,11 @@ status = "disabled"; }; + sysmgr: sysmgr@ffd08000 { + compatible = "altr,sys-mgr", "syscon"; + reg = <0xffd08000 0x4000>; + }; + /* Local timer */ timer@fffec600 { compatible = "arm,cortex-a9-twd-timer"; @@ -779,13 +798,6 @@ dma-names = "tx", "rx"; }; - rst: rstmgr@ffd05000 { - #reset-cells = <1>; - compatible = "altr,rst-mgr"; - reg = <0xffd05000 0x1000>; - altr,modrst-offset = <0x10>; - }; - usbphy0: usbphy@0 { #phy-cells = <0>; compatible = "usb-nop-xceiv"; @@ -829,10 +841,5 @@ clocks = <&osc1>; status = "disabled"; }; - - sysmgr: sysmgr@ffd08000 { - compatible = "altr,sys-mgr", "syscon"; - reg = <0xffd08000 0x4000>; - }; }; }; diff --git a/arch/arm/boot/dts/socfpga_arria10.dtsi b/arch/arm/boot/dts/socfpga_arria10.dtsi index 2340fcb2b535..cce9e50acf68 100644 --- a/arch/arm/boot/dts/socfpga_arria10.dtsi +++ b/arch/arm/boot/dts/socfpga_arria10.dtsi @@ -519,6 +519,7 @@ compatible = "snps,designware-i2c"; reg = <0xffc02200 0x100>; interrupts = <0 105 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&l4_sp_clk>; status = "disabled"; }; @@ -528,6 +529,7 @@ compatible = "snps,designware-i2c"; reg = <0xffc02300 0x100>; interrupts = <0 106 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&l4_sp_clk>; status = "disabled"; }; @@ -537,6 +539,7 @@ compatible = "snps,designware-i2c"; reg = <0xffc02400 0x100>; interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&l4_sp_clk>; status = "disabled"; }; @@ -546,6 +549,7 @@ compatible = "snps,designware-i2c"; reg = <0xffc02500 0x100>; interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&l4_sp_clk>; status = "disabled"; }; @@ -555,6 +559,7 @@ compatible = "snps,designware-i2c"; reg = <0xffc02600 0x100>; interrupts = <0 109 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&l4_sp_clk>; status = "disabled"; }; @@ -658,6 +663,7 @@ interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; + clocks = <&l4_sp_clk>; status = "disabled"; }; @@ -692,6 +698,8 @@ compatible = "snps,dwc2"; reg = <0xffb40000 0xffff>; interrupts = <0 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&usb_clk>; + clock-names = "otg"; phys = <&usbphy0>; phy-names = "usb2-phy"; status = "disabled"; diff --git a/arch/arm/boot/dts/socfpga_arria10_socdk.dtsi b/arch/arm/boot/dts/socfpga_arria10_socdk.dtsi index 99aa9a1c8af0..567df98f1bb5 100644 --- a/arch/arm/boot/dts/socfpga_arria10_socdk.dtsi +++ b/arch/arm/boot/dts/socfpga_arria10_socdk.dtsi @@ -70,6 +70,33 @@ status = "okay"; }; +&i2c1 { + speed-mode = <0>; + status = "okay"; + + /* + * adjust the falling times to decrease the i2c frequency to 50Khz + * because the LCD module does not work at the standard 100Khz + */ + i2c-sda-falling-time-ns = <6000>; + i2c-scl-falling-time-ns = <6000>; + + eeprom@51 { + compatible = "atmel,24c32"; + reg = <0x51>; + pagesize = <32>; + }; + + rtc@68 { + compatible = "dallas,ds1339"; + reg = <0x68>; + }; +}; + &uart1 { status = "okay"; }; + +&usb0 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/stih407-b2120.dts b/arch/arm/boot/dts/stih407-b2120.dts index 6d93475be554..c8ad905d0309 100644 --- a/arch/arm/boot/dts/stih407-b2120.dts +++ b/arch/arm/boot/dts/stih407-b2120.dts @@ -25,6 +25,7 @@ aliases { ttyAS0 = &sbc_serial0; + ethernet0 = ðernet0; }; }; diff --git a/arch/arm/boot/dts/stih407-family.dtsi b/arch/arm/boot/dts/stih407-family.dtsi index 0c24fcb03577..81f81214cdf9 100644 --- a/arch/arm/boot/dts/stih407-family.dtsi +++ b/arch/arm/boot/dts/stih407-family.dtsi @@ -152,6 +152,19 @@ <ST_IRQ_SYSCFG_DISABLED>; }; + /* Display */ + vtg_main: sti-vtg-main@8d02800 { + compatible = "st,vtg"; + reg = <0x8d02800 0x200>; + interrupts = <GIC_SPI 108 IRQ_TYPE_NONE>; + }; + + vtg_aux: sti-vtg-aux@8d00200 { + compatible = "st,vtg"; + reg = <0x8d00200 0x100>; + interrupts = <GIC_SPI 109 IRQ_TYPE_NONE>; + }; + serial@9830000 { compatible = "st,asc"; reg = <0x9830000 0x2c>; @@ -396,6 +409,8 @@ interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; clock-names = "ssc"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1_default>; status = "disabled"; }; @@ -406,6 +421,8 @@ interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; clock-names = "ssc"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi2_default>; status = "disabled"; }; @@ -416,6 +433,8 @@ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; clock-names = "ssc"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi3_default>; status = "disabled"; }; @@ -426,6 +445,8 @@ interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; clock-names = "ssc"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi4_default>; status = "disabled"; }; @@ -437,6 +458,8 @@ interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk_sysin>; clock-names = "ssc"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi10_default>; status = "disabled"; }; @@ -447,6 +470,8 @@ interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk_sysin>; clock-names = "ssc"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi11_default>; status = "disabled"; }; @@ -457,6 +482,8 @@ interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk_sysin>; clock-names = "ssc"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi12_default>; status = "disabled"; }; @@ -585,7 +612,6 @@ /* COMMS PWM Module */ pwm0: pwm@9810000 { compatible = "st,sti-pwm"; - status = "okay"; #pwm-cells = <2>; reg = <0x9810000 0x68>; pinctrl-names = "default"; @@ -593,12 +619,13 @@ clock-names = "pwm"; clocks = <&clk_sysin>; st,pwm-num-chan = <1>; + + status = "disabled"; }; /* SBC PWM Module */ pwm1: pwm@9510000 { compatible = "st,sti-pwm"; - status = "okay"; #pwm-cells = <2>; reg = <0x9510000 0x68>; pinctrl-names = "default"; @@ -609,6 +636,49 @@ clock-names = "pwm"; clocks = <&clk_sysin>; st,pwm-num-chan = <4>; + + status = "disabled"; + }; + + rng10: rng@08a89000 { + compatible = "st,rng"; + reg = <0x08a89000 0x1000>; + clocks = <&clk_sysin>; + status = "okay"; + }; + + rng11: rng@08a8a000 { + compatible = "st,rng"; + reg = <0x08a8a000 0x1000>; + clocks = <&clk_sysin>; + status = "okay"; + }; + + ethernet0: dwmac@9630000 { + device_type = "network"; + status = "disabled"; + compatible = "st,stih407-dwmac", "snps,dwmac", "snps,dwmac-3.710"; + reg = <0x9630000 0x8000>, <0x80 0x4>; + reg-names = "stmmaceth", "sti-ethconf"; + + st,syscon = <&syscfg_sbc_reg 0x80>; + st,gmac_en; + resets = <&softreset STIH407_ETH1_SOFTRESET>; + reset-names = "stmmaceth"; + + interrupts = <GIC_SPI 98 IRQ_TYPE_NONE>, + <GIC_SPI 99 IRQ_TYPE_NONE>; + interrupt-names = "macirq", "eth_wake_irq"; + + /* DMA Bus Mode */ + snps,pbl = <8>; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rgmii1>; + + clock-names = "stmmaceth", "sti-ethclk"; + clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>, + <&clk_s_c0_flexgen CLK_ETH_PHY>; }; rng10: rng@08a89000 { diff --git a/arch/arm/boot/dts/stih407-pinctrl.dtsi b/arch/arm/boot/dts/stih407-pinctrl.dtsi index 1683debd0854..a538ae52d32b 100644 --- a/arch/arm/boot/dts/stih407-pinctrl.dtsi +++ b/arch/arm/boot/dts/stih407-pinctrl.dtsi @@ -53,7 +53,7 @@ reg = <0x0961f080 0x4>; reg-names = "irqmux"; interrupts = <GIC_SPI 188 IRQ_TYPE_NONE>; - interrupts-names = "irqmux"; + interrupt-names = "irqmux"; ranges = <0 0x09610000 0x6000>; pio0: gpio@09610000 { @@ -107,12 +107,38 @@ st,retime-pin-mask = <0x3f>; }; + cec0 { + pinctrl_cec0_default: cec0-default { + st,pins { + hdmi_cec = <&pio2 4 ALT1 BIDIR>; + }; + }; + }; + rc { pinctrl_ir: ir0 { st,pins { ir = <&pio4 0 ALT2 IN>; }; }; + + pinctrl_uhf: uhf0 { + st,pins { + ir = <&pio4 1 ALT2 IN>; + }; + }; + + pinctrl_tx: tx0 { + st,pins { + tx = <&pio4 2 ALT2 OUT>; + }; + }; + + pinctrl_tx_od: tx_od0 { + st,pins { + tx_od = <&pio4 3 ALT2 OUT>; + }; + }; }; /* SBC_ASC0 - UART10 */ @@ -190,9 +216,9 @@ rxd2 = <&pio1 6 ALT1 IN DE_IO 0 CLK_A>; rxd3 = <&pio1 7 ALT1 IN DE_IO 0 CLK_A>; rxdv = <&pio2 0 ALT1 IN DE_IO 0 CLK_A>; - rxclk = <&pio2 2 ALT1 IN NICLK 500 CLK_A>; + rxclk = <&pio2 2 ALT1 IN NICLK 0 CLK_A>; clk125 = <&pio3 7 ALT4 IN NICLK 0 CLK_A>; - phyclk = <&pio2 3 ALT4 OUT NICLK 1750 CLK_B>; + phyclk = <&pio2 3 ALT4 OUT NICLK 1250 CLK_B>; }; }; @@ -230,6 +256,33 @@ phyclk = <&pio2 3 ALT1 OUT NICLK 0 CLK_A>; }; }; + + pinctrl_rmii1: rmii1-0 { + st,pins { + txd0 = <&pio0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txd1 = <&pio0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txen = <&pio0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + mdio = <&pio1 0 ALT1 OUT BYPASS 0>; + mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>; + mdint = <&pio1 3 ALT1 IN BYPASS 0>; + rxd0 = <&pio1 4 ALT1 IN SE_NICLK_IO 0 CLK_B>; + rxd1 = <&pio1 5 ALT1 IN SE_NICLK_IO 0 CLK_B>; + rxdv = <&pio2 0 ALT1 IN SE_NICLK_IO 0 CLK_B>; + rx_er = <&pio2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>; + }; + }; + + pinctrl_rmii1_phyclk: rmii1_phyclk { + st,pins { + phyclk = <&pio2 3 ALT1 OUT NICLK 0 CLK_A>; + }; + }; + + pinctrl_rmii1_phyclk_ext: rmii1_phyclk_ext { + st,pins { + phyclk = <&pio2 3 ALT2 IN NICLK 0 CLK_A>; + }; + }; }; pwm1 { @@ -254,6 +307,57 @@ }; }; }; + + spi10 { + pinctrl_spi10_default: spi10-4w-alt1-0 { + st,pins { + mtsr = <&pio4 6 ALT1 OUT>; + mrst = <&pio4 7 ALT1 IN>; + scl = <&pio4 5 ALT1 OUT>; + }; + }; + + pinctrl_spi10_3w_alt1_0: spi10-3w-alt1-0 { + st,pins { + mtsr = <&pio4 6 ALT1 BIDIR_PU>; + scl = <&pio4 5 ALT1 OUT>; + }; + }; + }; + + spi11 { + pinctrl_spi11_default: spi11-4w-alt2-0 { + st,pins { + mtsr = <&pio3 1 ALT2 OUT>; + mrst = <&pio3 0 ALT2 IN>; + scl = <&pio3 2 ALT2 OUT>; + }; + }; + + pinctrl_spi11_3w_alt2_0: spi11-3w-alt2-0 { + st,pins { + mtsr = <&pio3 1 ALT2 BIDIR_PU>; + scl = <&pio3 2 ALT2 OUT>; + }; + }; + }; + + spi12 { + pinctrl_spi12_default: spi12-4w-alt2-0 { + st,pins { + mtsr = <&pio3 6 ALT2 OUT>; + mrst = <&pio3 4 ALT2 IN>; + scl = <&pio3 7 ALT2 OUT>; + }; + }; + + pinctrl_spi12_3w_alt2_0: spi12-3w-alt2-0 { + st,pins { + mtsr = <&pio3 6 ALT2 BIDIR_PU>; + scl = <&pio3 7 ALT2 OUT>; + }; + }; + }; }; pin-controller-front0 { @@ -264,7 +368,7 @@ reg = <0x0920f080 0x4>; reg-names = "irqmux"; interrupts = <GIC_SPI 189 IRQ_TYPE_NONE>; - interrupts-names = "irqmux"; + interrupt-names = "irqmux"; ranges = <0 0x09200000 0x10000>; pio10: pio@09200000 { @@ -422,20 +526,180 @@ }; i2c3 { - pinctrl_i2c3_default: i2c3-default { + pinctrl_i2c3_default: i2c3-alt1-0 { st,pins { sda = <&pio18 6 ALT1 BIDIR>; scl = <&pio18 5 ALT1 BIDIR>; }; }; + pinctrl_i2c3_alt1_1: i2c3-alt1-1 { + st,pins { + sda = <&pio17 7 ALT1 BIDIR>; + scl = <&pio17 6 ALT1 BIDIR>; + }; + }; + pinctrl_i2c3_alt3_0: i2c3-alt3-0 { + st,pins { + sda = <&pio13 6 ALT3 BIDIR>; + scl = <&pio13 5 ALT3 BIDIR>; + }; + }; }; spi0 { - pinctrl_spi0_default: spi0-default { + pinctrl_spi0_default: spi0-4w-alt2-0 { + st,pins { + mtsr = <&pio10 6 ALT2 OUT>; + mrst = <&pio10 7 ALT2 IN>; + scl = <&pio10 5 ALT2 OUT>; + }; + }; + + pinctrl_spi0_3w_alt2_0: spi0-3w-alt2-0 { + st,pins { + mtsr = <&pio10 6 ALT2 BIDIR_PU>; + scl = <&pio10 5 ALT2 OUT>; + }; + }; + + pinctrl_spi0_4w_alt1_0: spi0-4w-alt1-0 { + st,pins { + mtsr = <&pio19 7 ALT1 OUT>; + mrst = <&pio19 5 ALT1 IN>; + scl = <&pio19 6 ALT1 OUT>; + }; + }; + + pinctrl_spi0_3w_alt1_0: spi0-3w-alt1-0 { + st,pins { + mtsr = <&pio19 7 ALT1 BIDIR_PU>; + scl = <&pio19 6 ALT1 OUT>; + }; + }; + }; + + spi1 { + pinctrl_spi1_default: spi1-4w-alt2-0 { + st,pins { + mtsr = <&pio11 1 ALT2 OUT>; + mrst = <&pio11 2 ALT2 IN>; + scl = <&pio11 0 ALT2 OUT>; + }; + }; + + pinctrl_spi1_3w_alt2_0: spi1-3w-alt2-0 { + st,pins { + mtsr = <&pio11 1 ALT2 BIDIR_PU>; + scl = <&pio11 0 ALT2 OUT>; + }; + }; + + pinctrl_spi1_4w_alt1_0: spi1-4w-alt1-0 { st,pins { - mtsr = <&pio12 6 ALT2 BIDIR>; - mrst = <&pio12 7 ALT2 BIDIR>; - scl = <&pio12 5 ALT2 BIDIR>; + mtsr = <&pio14 3 ALT1 OUT>; + mrst = <&pio14 4 ALT1 IN>; + scl = <&pio14 2 ALT1 OUT>; + }; + }; + + pinctrl_spi1_3w_alt1_0: spi1-3w-alt1-0 { + st,pins { + mtsr = <&pio14 3 ALT1 BIDIR_PU>; + scl = <&pio14 2 ALT1 OUT>; + }; + }; + }; + + spi2 { + pinctrl_spi2_default: spi2-4w-alt2-0 { + st,pins { + mtsr = <&pio12 6 ALT2 OUT>; + mrst = <&pio12 7 ALT2 IN>; + scl = <&pio12 5 ALT2 OUT>; + }; + }; + + pinctrl_spi2_3w_alt2_0: spi2-3w-alt2-0 { + st,pins { + mtsr = <&pio12 6 ALT2 BIDIR_PU>; + scl = <&pio12 5 ALT2 OUT>; + }; + }; + + pinctrl_spi2_4w_alt1_0: spi2-4w-alt1-0 { + st,pins { + mtsr = <&pio14 6 ALT1 OUT>; + mrst = <&pio14 7 ALT1 IN>; + scl = <&pio14 5 ALT1 OUT>; + }; + }; + + pinctrl_spi2_3w_alt1_0: spi2-3w-alt1-0 { + st,pins { + mtsr = <&pio14 6 ALT1 BIDIR_PU>; + scl = <&pio14 5 ALT1 OUT>; + }; + }; + + pinctrl_spi2_4w_alt2_1: spi2-4w-alt2-1 { + st,pins { + mtsr = <&pio15 6 ALT2 OUT>; + mrst = <&pio15 7 ALT2 IN>; + scl = <&pio15 5 ALT2 OUT>; + }; + }; + + pinctrl_spi2_3w_alt2_1: spi2-3w-alt2-1 { + st,pins { + mtsr = <&pio15 6 ALT2 BIDIR_PU>; + scl = <&pio15 5 ALT2 OUT>; + }; + }; + }; + + spi3 { + pinctrl_spi3_default: spi3-4w-alt3-0 { + st,pins { + mtsr = <&pio13 6 ALT3 OUT>; + mrst = <&pio13 7 ALT3 IN>; + scl = <&pio13 5 ALT3 OUT>; + }; + }; + + pinctrl_spi3_3w_alt3_0: spi3-3w-alt3-0 { + st,pins { + mtsr = <&pio13 6 ALT3 BIDIR_PU>; + scl = <&pio13 5 ALT3 OUT>; + }; + }; + + pinctrl_spi3_4w_alt1_0: spi3-4w-alt1-0 { + st,pins { + mtsr = <&pio17 7 ALT1 OUT>; + mrst = <&pio17 5 ALT1 IN>; + scl = <&pio17 6 ALT1 OUT>; + }; + }; + + pinctrl_spi3_3w_alt1_0: spi3-3w-alt1-0 { + st,pins { + mtsr = <&pio17 7 ALT1 BIDIR_PU>; + scl = <&pio17 6 ALT1 OUT>; + }; + }; + + pinctrl_spi3_4w_alt1_1: spi3-4w-alt1-1 { + st,pins { + mtsr = <&pio18 6 ALT1 OUT>; + mrst = <&pio18 7 ALT1 IN>; + scl = <&pio18 5 ALT1 OUT>; + }; + }; + + pinctrl_spi3_3w_alt1_1: spi3-3w-alt1-1 { + st,pins { + mtsr = <&pio18 6 ALT1 BIDIR_PU>; + scl = <&pio18 5 ALT1 OUT>; }; }; }; @@ -627,6 +891,18 @@ }; }; }; + + systrace { + pinctrl_systrace_default: systrace-default { + st,pins { + trc_data0 = <&pio11 3 ALT5 OUT>; + trc_data1 = <&pio11 4 ALT5 OUT>; + trc_data2 = <&pio11 5 ALT5 OUT>; + trc_data3 = <&pio11 6 ALT5 OUT>; + trc_clk = <&pio11 7 ALT5 OUT>; + }; + }; + }; }; pin-controller-front1 { @@ -637,7 +913,7 @@ reg = <0x0921f080 0x4>; reg-names = "irqmux"; interrupts = <GIC_SPI 190 IRQ_TYPE_NONE>; - interrupts-names = "irqmux"; + interrupt-names = "irqmux"; ranges = <0 0x09210000 0x10000>; tsin4 { @@ -670,7 +946,7 @@ reg = <0x0922f080 0x4>; reg-names = "irqmux"; interrupts = <GIC_SPI 191 IRQ_TYPE_NONE>; - interrupts-names = "irqmux"; + interrupt-names = "irqmux"; ranges = <0 0x09220000 0x6000>; pio30: gpio@09220000 { @@ -758,6 +1034,47 @@ }; }; }; + + spi4 { + pinctrl_spi4_default: spi4-4w-alt1-0 { + st,pins { + mtsr = <&pio30 1 ALT1 OUT>; + mrst = <&pio30 2 ALT1 IN>; + scl = <&pio30 0 ALT1 OUT>; + }; + }; + + pinctrl_spi4_3w_alt1_0: spi4-3w-alt1-0 { + st,pins { + mtsr = <&pio30 1 ALT1 BIDIR_PU>; + scl = <&pio30 0 ALT1 OUT>; + }; + }; + + pinctrl_spi4_4w_alt3_0: spi4-4w-alt3-0 { + st,pins { + mtsr = <&pio34 1 ALT3 OUT>; + mrst = <&pio34 2 ALT3 IN>; + scl = <&pio34 0 ALT3 OUT>; + }; + }; + + pinctrl_spi4_3w_alt3_0: spi4-3w-alt3-0 { + st,pins { + mtsr = <&pio34 1 ALT3 BIDIR_PU>; + scl = <&pio34 0 ALT3 OUT>; + }; + }; + }; + + serial3 { + pinctrl_serial3: serial3-0 { + st,pins { + tx = <&pio31 3 ALT1 OUT>; + rx = <&pio31 4 ALT1 IN>; + }; + }; + }; }; pin-controller-flash { @@ -811,6 +1128,57 @@ emmc_d7 = <&pio41 7 ALT1 BIDIR_PU>; }; }; + pinctrl_sd0: sd0-0 { + st,pins { + sd_clk = <&pio40 6 ALT1 BIDIR>; + sd_cmd = <&pio40 7 ALT1 BIDIR_PU>; + sd_dat0 = <&pio41 0 ALT1 BIDIR_PU>; + sd_dat1 = <&pio41 1 ALT1 BIDIR_PU>; + sd_dat2 = <&pio41 2 ALT1 BIDIR_PU>; + sd_dat3 = <&pio41 3 ALT1 BIDIR_PU>; + sd_led = <&pio42 0 ALT2 OUT>; + sd_pwren = <&pio42 2 ALT2 OUT>; + sd_vsel = <&pio42 3 ALT2 OUT>; + sd_cd = <&pio42 4 ALT2 IN>; + sd_wp = <&pio42 5 ALT2 IN>; + }; + }; + }; + + fsm { + pinctrl_fsm: fsm { + st,pins { + spi-fsm-clk = <&pio40 1 ALT1 OUT>; + spi-fsm-cs = <&pio40 0 ALT1 OUT>; + spi-fsm-mosi = <&pio40 2 ALT1 OUT>; + spi-fsm-miso = <&pio40 3 ALT1 IN>; + spi-fsm-hol = <&pio40 5 ALT1 OUT>; + spi-fsm-wp = <&pio40 4 ALT1 OUT>; + }; + }; + }; + + nand { + pinctrl_nand: nand { + st,pins { + nand_cs1 = <&pio40 6 ALT3 OUT>; + nand_cs0 = <&pio40 7 ALT3 OUT>; + nand_d0 = <&pio41 0 ALT3 BIDIR>; + nand_d1 = <&pio41 1 ALT3 BIDIR>; + nand_d2 = <&pio41 2 ALT3 BIDIR>; + nand_d3 = <&pio41 3 ALT3 BIDIR>; + nand_d4 = <&pio41 4 ALT3 BIDIR>; + nand_d5 = <&pio41 5 ALT3 BIDIR>; + nand_d6 = <&pio41 6 ALT3 BIDIR>; + nand_d7 = <&pio41 7 ALT3 BIDIR>; + nand_we = <&pio42 0 ALT3 OUT>; + nand_dqs = <&pio42 1 ALT3 OUT>; + nand_ale = <&pio42 2 ALT3 OUT>; + nand_cle = <&pio42 3 ALT3 OUT>; + nand_rnb = <&pio42 4 ALT3 IN>; + nand_oe = <&pio42 5 ALT3 OUT>; + }; + }; }; }; }; diff --git a/arch/arm/boot/dts/stih407.dtsi b/arch/arm/boot/dts/stih407.dtsi index 6b914e4bb099..d60f0d8add26 100644 --- a/arch/arm/boot/dts/stih407.dtsi +++ b/arch/arm/boot/dts/stih407.dtsi @@ -10,19 +10,6 @@ #include "stih407-family.dtsi" / { soc { - /* Display */ - vtg_main: sti-vtg-main@8d02800 { - compatible = "st,vtg"; - reg = <0x8d02800 0x200>; - interrupts = <GIC_SPI 108 IRQ_TYPE_NONE>; - }; - - vtg_aux: sti-vtg-aux@8d00200 { - compatible = "st,vtg"; - reg = <0x8d00200 0x100>; - interrupts = <GIC_SPI 109 IRQ_TYPE_NONE>; - }; - sti-display-subsystem { compatible = "st,sti-display-subsystem"; #address-cells = <1>; diff --git a/arch/arm/boot/dts/stih410-b2120.dts b/arch/arm/boot/dts/stih410-b2120.dts index 16f02c5e33a4..118ac284fc4b 100644 --- a/arch/arm/boot/dts/stih410-b2120.dts +++ b/arch/arm/boot/dts/stih410-b2120.dts @@ -25,6 +25,7 @@ aliases { ttyAS0 = &sbc_serial0; + ethernet0 = ðernet0; }; soc { @@ -35,5 +36,29 @@ sd-uhs-sdr104; sd-uhs-ddr50; }; + + usb2_picophy1: phy2 { + status = "okay"; + }; + + usb2_picophy2: phy3 { + status = "okay"; + }; + + ohci0: usb@9a03c00 { + status = "okay"; + }; + + ehci0: usb@9a03e00 { + status = "okay"; + }; + + ohci1: usb@9a83c00 { + status = "okay"; + }; + + ehci1: usb@9a83e00 { + status = "okay"; + }; }; }; diff --git a/arch/arm/boot/dts/stih410.dtsi b/arch/arm/boot/dts/stih410.dtsi index 8c6e61a27234..18ed1ad10d32 100644 --- a/arch/arm/boot/dts/stih410.dtsi +++ b/arch/arm/boot/dts/stih410.dtsi @@ -22,6 +22,8 @@ resets = <&softreset STIH407_PICOPHY_SOFTRESET>, <&picophyreset STIH407_PICOPHY0_RESET>; reset-names = "global", "port"; + + status = "disabled"; }; usb2_picophy2: phy3 { @@ -31,6 +33,8 @@ resets = <&softreset STIH407_PICOPHY_SOFTRESET>, <&picophyreset STIH407_PICOPHY1_RESET>; reset-names = "global", "port"; + + status = "disabled"; }; ohci0: usb@9a03c00 { @@ -43,6 +47,8 @@ reset-names = "power", "softreset"; phys = <&usb2_picophy1>; phy-names = "usb"; + + status = "disabled"; }; ehci0: usb@9a03e00 { @@ -57,6 +63,8 @@ reset-names = "power", "softreset"; phys = <&usb2_picophy1>; phy-names = "usb"; + + status = "disabled"; }; ohci1: usb@9a83c00 { @@ -69,6 +77,8 @@ reset-names = "power", "softreset"; phys = <&usb2_picophy2>; phy-names = "usb"; + + status = "disabled"; }; ehci1: usb@9a83e00 { @@ -83,19 +93,8 @@ reset-names = "power", "softreset"; phys = <&usb2_picophy2>; phy-names = "usb"; - }; - - /* Display */ - vtg_main: sti-vtg-main@8d02800 { - compatible = "st,vtg"; - reg = <0x8d02800 0x200>; - interrupts = <GIC_SPI 108 IRQ_TYPE_NONE>; - }; - vtg_aux: sti-vtg-aux@8d00200 { - compatible = "st,vtg"; - reg = <0x8d00200 0x100>; - interrupts = <GIC_SPI 109 IRQ_TYPE_NONE>; + status = "disabled"; }; sti-display-subsystem { diff --git a/arch/arm/boot/dts/stih418-b2199.dts b/arch/arm/boot/dts/stih418-b2199.dts index 82eee39ccb31..772d2bb07e5f 100644 --- a/arch/arm/boot/dts/stih418-b2199.dts +++ b/arch/arm/boot/dts/stih418-b2199.dts @@ -24,6 +24,7 @@ aliases { ttyAS0 = &sbc_serial0; + ethernet0 = ðernet0; }; soc { @@ -101,5 +102,12 @@ st_dwc3: dwc3@8f94000 { status = "okay"; }; + + ethernet0: dwmac@9630000 { + st,tx-retime-src = "clkgen"; + status = "okay"; + phy-mode = "rgmii"; + fixed-link = <0 1 1000 0 0>; + }; }; }; diff --git a/arch/arm/boot/dts/stih418-clock.dtsi b/arch/arm/boot/dts/stih418-clock.dtsi index 148e1772465f..ae6d9978ea19 100644 --- a/arch/arm/boot/dts/stih418-clock.dtsi +++ b/arch/arm/boot/dts/stih418-clock.dtsi @@ -44,7 +44,7 @@ clockgen_a9_pll: clockgen-a9-pll { #clock-cells = <1>; - compatible = "st,stih407-plls-c32-a9", "st,clkgen-plls-c32"; + compatible = "st,stih418-plls-c28-a9", "st,clkgen-plls-c32"; clocks = <&clk_sysin>; diff --git a/arch/arm/boot/dts/stih418.dtsi b/arch/arm/boot/dts/stih418.dtsi index 8160a75539a4..965f88160718 100644 --- a/arch/arm/boot/dts/stih418.dtsi +++ b/arch/arm/boot/dts/stih418.dtsi @@ -99,5 +99,11 @@ phys = <&usb2_picophy2>; phy-names = "usb"; }; + + mmc0: sdhci@09060000 { + assigned-clocks = <&clk_s_c0_flexgen CLK_MMC_0>; + assigned-clock-parents = <&clk_s_c0_pll1 0>; + assigned-clock-rates = <200000000>; + }; }; }; diff --git a/arch/arm/boot/dts/stihxxx-b2120.dtsi b/arch/arm/boot/dts/stihxxx-b2120.dtsi index f589fe487f13..ad21a4293a33 100644 --- a/arch/arm/boot/dts/stihxxx-b2120.dtsi +++ b/arch/arm/boot/dts/stihxxx-b2120.dtsi @@ -27,6 +27,14 @@ }; }; + pwm0: pwm@9810000 { + status = "okay"; + }; + + pwm1: pwm@9510000 { + status = "okay"; + }; + i2c@9842000 { status = "okay"; }; @@ -79,5 +87,11 @@ status = "okay"; }; + ethernet0: dwmac@9630000 { + st,tx-retime-src = "clkgen"; + status = "okay"; + phy-mode = "rgmii"; + fixed-link = <0 1 1000 0 0>; + }; }; }; diff --git a/arch/arm/boot/dts/sun4i-a10-a1000.dts b/arch/arm/boot/dts/sun4i-a10-a1000.dts index 2630d78d9e04..97570cb7f2fc 100644 --- a/arch/arm/boot/dts/sun4i-a10-a1000.dts +++ b/arch/arm/boot/dts/sun4i-a10-a1000.dts @@ -93,6 +93,10 @@ status = "okay"; }; +&codec { + status = "okay"; +}; + &ehci0 { status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts b/arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts index 143056872650..53660894ea95 100644 --- a/arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts +++ b/arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts @@ -78,6 +78,18 @@ }; }; +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; +}; + &lradc { vref-supply = <®_vcc3v0>; status = "okay"; diff --git a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts b/arch/arm/boot/dts/sun4i-a10-cubieboard.dts index 046a84d9719d..710e2ef516a8 100644 --- a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts +++ b/arch/arm/boot/dts/sun4i-a10-cubieboard.dts @@ -83,6 +83,10 @@ status = "okay"; }; +&codec { + status = "okay"; +}; + &cpu0 { cpu-supply = <®_dcdc2>; }; diff --git a/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts b/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts index 570754d8df67..3f0aeb8288cd 100644 --- a/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts +++ b/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts @@ -47,6 +47,7 @@ #include "sunxi-common-regulators.dtsi" #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> / { model = "Gemei G9 Tablet"; @@ -64,7 +65,7 @@ /* * TODO: * 2x cameras via CSI - * bma250 IRQs + * audio * AXP battery management * NAND * OTG @@ -103,12 +104,8 @@ bma250@18 { compatible = "bosch,bma250"; reg = <0x18>; - - /* - * TODO: interrupt pins: - * int1 - PH00 - * int2 - PI10 - */ + interrupt-parent = <&pio>; + interrupts = <7 0 IRQ_TYPE_EDGE_RISING>; /* PH00 / EINT0 */ }; }; diff --git a/arch/arm/boot/dts/sun4i-a10-inet1.dts b/arch/arm/boot/dts/sun4i-a10-inet1.dts new file mode 100644 index 000000000000..487ce63519dc --- /dev/null +++ b/arch/arm/boot/dts/sun4i-a10-inet1.dts @@ -0,0 +1,226 @@ +/* + * Copyright 2015 Hans de Goede <hdegoede@redhat.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun4i-a10.dtsi" +#include "sunxi-common-regulators.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> + +/ { + model = "iNet-1"; + compatible = "inet-tek,inet1", "allwinner,sun4i-a10"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + reg = <0x34>; + interrupts = <0>; + }; +}; + +#include "axp209.dtsi" + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; + + /* Accelerometer */ + bma250@18 { + compatible = "bosch,bma250"; + reg = <0x18>; + interrupt-parent = <&pio>; + interrupts = <7 0 IRQ_TYPE_EDGE_RISING>; /* PH0 / EINT0 */ + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; +}; + +&lradc { + vref-supply = <®_ldo2>; + status = "okay"; + + button@200 { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + channel = <0>; + voltage = <200000>; + }; + + button@1000 { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + channel = <0>; + voltage = <1000000>; + }; + + button@1200 { + label = "Home"; + linux,code = <KEY_HOMEPAGE>; + channel = <0>; + voltage = <1200000>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ + cd-inverted; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&otg_sram { + status = "okay"; +}; + +&pio { + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PH5"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>; + }; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd-int-dll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_usb0_vbus { + status = "okay"; +}; + +®_usb1_vbus { + status = "okay"; +}; + +®_usb2_vbus { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */ + usb0_vbus-supply = <®_usb0_vbus>; + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun4i-a10-inet97fv2.dts b/arch/arm/boot/dts/sun4i-a10-inet97fv2.dts index 6c927a824ba2..77c31dab86b1 100644 --- a/arch/arm/boot/dts/sun4i-a10-inet97fv2.dts +++ b/arch/arm/boot/dts/sun4i-a10-inet97fv2.dts @@ -47,6 +47,7 @@ #include "sunxi-common-regulators.dtsi" #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> / { model = "INet-97F Rev 02"; @@ -61,8 +62,8 @@ }; }; -&ehci0 { - status = "okay"; +&cpu0 { + cpu-supply = <®_dcdc2>; }; &ehci1 { @@ -75,12 +76,62 @@ status = "okay"; axp209: pmic@34 { - compatible = "x-powers,axp209"; reg = <0x34>; interrupts = <0>; + }; +}; + +#include "axp209.dtsi" + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; +}; + +&lradc { + vref-supply = <®_ldo2>; + status = "okay"; + + button@200 { + label = "Menu"; + linux,code = <KEY_MENU>; + channel = <0>; + voltage = <200000>; + }; + + button@600 { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + channel = <0>; + voltage = <600000>; + }; + + button@800 { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + channel = <0>; + voltage = <800000>; + }; + + button@1000 { + label = "Home"; + linux,code = <KEY_HOMEPAGE>; + channel = <0>; + voltage = <1000000>; + }; - interrupt-controller; - #interrupt-cells = <1>; + button@1200 { + label = "Esc"; + linux,code = <KEY_ESC>; + channel = <0>; + voltage = <1200000>; }; }; @@ -94,15 +145,52 @@ status = "okay"; }; -&ohci0 { +&otg_sram { status = "okay"; }; -&ohci1 { - status = "okay"; +&pio { + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PH5"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>; + }; }; -®_usb1_vbus { +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd-int-dll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_usb0_vbus { status = "okay"; }; @@ -116,8 +204,17 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + &usbphy { - usb1_vbus-supply = <®_usb1_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */ + usb0_vbus-supply = <®_usb0_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts b/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts new file mode 100644 index 000000000000..2fffc0434075 --- /dev/null +++ b/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts @@ -0,0 +1,227 @@ +/* + * Copyright 2015 Hans de Goede <hdegoede@redhat.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun4i-a10.dtsi" +#include "sunxi-common-regulators.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> + +/ { + model = "iNet-9F Rev 03"; + compatible = "inet-tek,inet9f-rev03", "allwinner,sun4i-a10"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&ehci1 { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + reg = <0x34>; + interrupts = <0>; + }; +}; + +#include "axp209.dtsi" + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; + + /* Accelerometer */ + bma250@18 { + compatible = "bosch,bma250"; + reg = <0x18>; + interrupt-parent = <&pio>; + interrupts = <7 0 IRQ_TYPE_EDGE_RISING>; /* PH0 / EINT0 */ + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; +}; + +&lradc { + vref-supply = <®_ldo2>; + status = "okay"; + + button@200 { + label = "Menu"; + linux,code = <KEY_MENU>; + channel = <0>; + voltage = <200000>; + }; + + button@600 { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + channel = <0>; + voltage = <600000>; + }; + + button@800 { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + channel = <0>; + voltage = <800000>; + }; + + button@1000 { + label = "Home"; + linux,code = <KEY_HOMEPAGE>; + channel = <0>; + voltage = <1000000>; + }; + + button@1200 { + label = "Esc"; + linux,code = <KEY_ESC>; + channel = <0>; + voltage = <1200000>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ + cd-inverted; + status = "okay"; +}; + +&otg_sram { + status = "okay"; +}; + +&pio { + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PH5"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>; + }; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd-int-dll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_usb0_vbus { + status = "okay"; +}; + +®_usb2_vbus { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */ + usb0_vbus-supply = <®_usb0_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts b/arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts index dc2f2aeaff07..7afc7a64eef1 100644 --- a/arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts +++ b/arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts @@ -156,6 +156,10 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { emac_power_pin_q5: emac_power_pin@0 { allwinner,pins = "PH19"; @@ -172,6 +176,11 @@ }; }; +®_usb0_vbus { + regulator-boot-on; + status = "okay"; +}; + ®_usb1_vbus { status = "okay"; }; @@ -186,7 +195,13 @@ status = "okay"; }; +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + &usbphy { + usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; diff --git a/arch/arm/boot/dts/sun4i-a10-marsboard.dts b/arch/arm/boot/dts/sun4i-a10-marsboard.dts index 02158bcd64ee..8e50723dbe02 100644 --- a/arch/arm/boot/dts/sun4i-a10-marsboard.dts +++ b/arch/arm/boot/dts/sun4i-a10-marsboard.dts @@ -91,6 +91,10 @@ status = "okay"; }; +&codec { + status = "okay"; +}; + &ehci0 { status = "okay"; }; @@ -154,6 +158,10 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { led_pins_marsboard: led_pins@0 { allwinner,pins = "PB5", "PB6", "PB7", "PB8"; @@ -161,6 +169,13 @@ allwinner,drive = <SUN4I_PINCTRL_10_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; }; ®_usb1_vbus { @@ -184,7 +199,15 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; diff --git a/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts b/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts index 28e32ad705cd..b350448c7217 100644 --- a/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts +++ b/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts @@ -124,6 +124,18 @@ }; }; +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; + + eeprom: eeprom@50 { + compatible = "atmel,24c16"; + reg = <0x50>; + pagesize = <16>; + }; +}; + &mdio { status = "okay"; diff --git a/arch/arm/boot/dts/sun4i-a10-pcduino.dts b/arch/arm/boot/dts/sun4i-a10-pcduino.dts index 4e3e1b9d8217..39034aa8e1ae 100644 --- a/arch/arm/boot/dts/sun4i-a10-pcduino.dts +++ b/arch/arm/boot/dts/sun4i-a10-pcduino.dts @@ -104,6 +104,10 @@ }; }; +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + &ehci0 { status = "okay"; }; @@ -129,12 +133,8 @@ status = "okay"; axp209: pmic@34 { - compatible = "x-powers,axp209"; reg = <0x34>; interrupts = <0>; - - interrupt-controller; - #interrupt-cells = <1>; }; }; @@ -164,6 +164,10 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { led_pins_pcduino: led_pins@0 { allwinner,pins = "PH15", "PH16"; @@ -178,14 +182,40 @@ allwinner,drive = <SUN4I_PINCTRL_10_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; }; -®_usb1_vbus { - status = "okay"; +#include "axp209.dtsi" + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; }; -®_usb2_vbus { - status = "okay"; +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-int-dll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; }; &uart0 { @@ -194,8 +224,16 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + &usbphy { - usb1_vbus-supply = <®_usb1_vbus>; - usb2_vbus-supply = <®_usb2_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb1_vbus-supply = <®_vcc5v0>; /* USB1 VBUS is always on */ + usb2_vbus-supply = <®_vcc5v0>; /* USB2 VBUS is always on */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-pcduino2.dts b/arch/arm/boot/dts/sun4i-a10-pcduino2.dts new file mode 100644 index 000000000000..de483a1bf36a --- /dev/null +++ b/arch/arm/boot/dts/sun4i-a10-pcduino2.dts @@ -0,0 +1,78 @@ +/* + * Copyright 2015 Siarhei Siamashka <siarhei.siamashka@gmail.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/* + * The LinkSprite pcDuino2 board is almost identical to the older + * LinkSprite pcDuino1 board. The only software visible difference + * is that the pcDuino2 board got a USB VBUS voltage regulator, which + * is controlled by the PD2 pin (pulled-up by default). Also one of + * the USB host ports has been replaced with a USB WIFI chip. + */ + +#include "sun4i-a10-pcduino.dts" + +/ { + model = "LinkSprite pcDuino2"; + compatible = "linksprite,a10-pcduino2", "allwinner,sun4i-a10"; +}; + +&pio { + usb2_vbus_pin_pcduino2: usb2_vbus_pin@0 { + allwinner,pins = "PD2"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; +}; + +®_usb2_vbus { + pinctrl-names = "default"; + pinctrl-0 = <&usb2_vbus_pin_pcduino2>; + gpio = <&pio 3 2 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&usbphy { + usb1_vbus-supply = <®_vcc3v3>; /* USB WIFI is always on */ + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts b/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts new file mode 100644 index 000000000000..82e69c3820a2 --- /dev/null +++ b/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts @@ -0,0 +1,199 @@ +/* + * Copyright 2015 Hans de Goede <hdegoede@redhat.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun4i-a10.dtsi" +#include "sunxi-common-regulators.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> + +/ { + model = "Point of View Protab2-IPS9"; + compatible = "pov,protab2-ips9", "allwinner,sun4i-a10"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&ehci0 { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + reg = <0x34>; + interrupts = <0>; + }; +}; + +#include "axp209.dtsi" + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + /* pull-ups and devices require AXP209 LDO3 */ + status = "failed"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; +}; + +&lradc { + vref-supply = <®_ldo2>; + status = "okay"; + + button@400 { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + channel = <0>; + voltage = <400000>; + }; + + button@800 { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + channel = <0>; + voltage = <800000>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ + cd-inverted; + status = "okay"; +}; + +&otg_sram { + status = "okay"; +}; + +&pio { + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PH5"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>; + }; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd-int-dll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_usb0_vbus { + status = "okay"; +}; + +®_usb1_vbus { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */ + usb0_vbus-supply = <®_usb0_vbus>; + usb1_vbus-supply = <®_usb1_vbus>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun4i-a10.dtsi b/arch/arm/boot/dts/sun4i-a10.dtsi index 1f3c51a08113..aa90f319309b 100644 --- a/arch/arm/boot/dts/sun4i-a10.dtsi +++ b/arch/arm/boot/dts/sun4i-a10.dtsi @@ -45,6 +45,7 @@ #include <dt-bindings/thermal/thermal.h> +#include <dt-bindings/clock/sun4i-a10-pll2.h> #include <dt-bindings/dma/sun4i-a10.h> #include <dt-bindings/pinctrl/sun4i-a10.h> @@ -195,6 +196,15 @@ clock-output-names = "pll1"; }; + pll2: clk@01c20008 { + #clock-cells = <1>; + compatible = "allwinner,sun4i-a10-pll2-clk"; + reg = <0x01c20008 0x8>; + clocks = <&osc24M>; + clock-output-names = "pll2-1x", "pll2-2x", + "pll2-4x", "pll2-8x"; + }; + pll4: clk@01c20018 { #clock-cells = <0>; compatible = "allwinner,sun4i-a10-pll1-clk"; @@ -481,6 +491,14 @@ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "spi3"; }; + + codec_clk: clk@01c20140 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-codec-clk"; + reg = <0x01c20140 0x4>; + clocks = <&pll2 SUN4I_A10_PLL2_1X>; + clock-output-names = "codec"; + }; }; soc@01c00000 { @@ -1004,6 +1022,19 @@ status = "disabled"; }; + codec: codec@01c22c00 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun4i-a10-codec"; + reg = <0x01c22c00 0x40>; + interrupts = <30>; + clocks = <&apb0_gates 0>, <&codec_clk>; + clock-names = "apb", "codec"; + dmas = <&dma SUN4I_DMA_NORMAL 19>, + <&dma SUN4I_DMA_NORMAL 19>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + sid: eeprom@01c23800 { compatible = "allwinner,sun4i-a10-sid"; reg = <0x01c23800 0x10>; diff --git a/arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts b/arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts new file mode 100644 index 000000000000..d4ad02182353 --- /dev/null +++ b/arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts @@ -0,0 +1,159 @@ +/* + * Copyright 2015 Hans de Goede <hdegoede@redhat.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun5i-a10s.dtsi" +#include "sunxi-common-regulators.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> + +/ { + model = "Auxtek t003 A10s hdmi tv-stick"; + compatible = "allwinner,auxtek-t003", "allwinner,sun5i-a10s"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_t003>; + + red { + label = "t003-tv-dongle:red:usr"; + gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */ + default-state = "on"; + }; + }; +}; + +&ehci0 { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp152: pmic@30 { + compatible = "x-powers,axp152"; + reg = <0x30>; + interrupts = <0>; + interrupt-controller; + #interrupt-cells = <1>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t003>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */ + cd-inverted; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&otg_sram { + status = "okay"; +}; + +&pio { + mmc0_cd_pin_t003: mmc0_cd_pin@0 { + allwinner,pins = "PG1"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + led_pins_t003: led_pins@0 { + allwinner,pins = "PB2"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_20_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; +}; + +®_usb0_vbus { + gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */ + status = "okay"; +}; + +®_usb1_vbus { + gpio = <&pio 1 10 GPIO_ACTIVE_HIGH>; /* PB10 */ + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usb0_vbus_pin_a { + allwinner,pins = "PG13"; +}; + +&usb1_vbus_pin_a { + allwinner,pins = "PB10"; +}; + +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + +&usbphy { + usb0_vbus-supply = <®_usb0_vbus>; + usb1_vbus-supply = <®_usb1_vbus>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts index 5a422c1ff725..86d046a502e6 100644 --- a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts +++ b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts @@ -111,7 +111,7 @@ status = "okay"; at24@50 { - compatible = "at,24c16"; + compatible = "atmel,24c16"; pagesize = <16>; reg = <0x50>; read-only; diff --git a/arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts b/arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts new file mode 100644 index 000000000000..9fea918f949e --- /dev/null +++ b/arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts @@ -0,0 +1,224 @@ +/* + * Copyright 2015 Jelle van der Waa <jelle@vdwaa.nl> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun5i-a10s.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> + +/ { + model = "A10s-Wobo i5"; + compatible = "wobo,a10s-wobo-i5", "allwinner,sun5i-a10s"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_wobo_i5>; + + blue { + label = "a10s-wobo-i5:blue:usr"; + gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + reg_emac_3v3: emac-3v3 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&emac_power_pin_wobo>; + regulator-name = "emac-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + gpio = <&pio 0 2 GPIO_ACTIVE_HIGH>; + }; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&ehci0 { + status = "okay"; +}; + +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&emac_pins_b>; + phy = <&phy1>; + status = "okay"; +}; + +&emac_sram { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + reg = <0x34>; + interrupts = <0>; + }; +}; + +#include "axp209.dtsi" + +&mdio { + phy-supply = <®_emac_3v3>; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_wobo_i5>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */ + cd-inverted; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&otg_sram { + status = "okay"; +}; + +&pio { + led_pins_wobo_i5: led_pins@0 { + allwinner,pins = "PB2"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + mmc0_cd_pin_wobo_i5: mmc0_cd_pin@0 { + allwinner,pins = "PB3"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + emac_power_pin_wobo: emac_power_pin@0 { + allwinner,pins = "PA02"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd-int-dll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_ldo3 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +®_usb1_vbus { + gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + +&usb1_vbus_pin_a { + allwinner,pins = "PG12"; +}; + +&usbphy { + usb1_vbus-supply = <®_usb1_vbus>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun5i-a10s.dtsi b/arch/arm/boot/dts/sun5i-a10s.dtsi index a513b416a807..bddd0de88af6 100644 --- a/arch/arm/boot/dts/sun5i-a10s.dtsi +++ b/arch/arm/boot/dts/sun5i-a10s.dtsi @@ -77,6 +77,15 @@ clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>; status = "disabled"; }; + + framebuffer@2 { + compatible = "allwinner,simple-framebuffer", + "simple-framebuffer"; + allwinner,pipeline = "de_be0-lcd0-tve0"; + clocks = <&pll5 1>, <&ahb_gates 34>, <&ahb_gates 36>, + <&ahb_gates 44>; + status = "disabled"; + }; }; clocks { @@ -156,6 +165,14 @@ #size-cells = <0>; }; + pwm: pwm@01c20e00 { + compatible = "allwinner,sun5i-a10s-pwm"; + reg = <0x01c20e00 0xc>; + clocks = <&osc24M>; + #pwm-cells = <3>; + status = "disabled"; + }; + uart0: serial@01c28000 { compatible = "snps,dw-apb-uart"; reg = <0x01c28000 0x400>; @@ -195,13 +212,6 @@ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; - uart3_pins_a: uart3@0 { - allwinner,pins = "PG9", "PG10"; - allwinner,function = "uart3"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; - }; - emac_pins_a: emac0@0 { allwinner,pins = "PA0", "PA1", "PA2", "PA3", "PA4", "PA5", "PA6", @@ -213,6 +223,17 @@ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + emac_pins_b: emac0@1 { + allwinner,pins = "PD6", "PD7", "PD10", + "PD11", "PD12", "PD13", "PD14", + "PD15", "PD18", "PD19", "PD20", + "PD21", "PD22", "PD23", "PD24", + "PD25", "PD26", "PD27"; + allwinner,function = "emac"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + mmc1_pins_a: mmc1@0 { allwinner,pins = "PG3", "PG4", "PG5", "PG6", "PG7", "PG8"; diff --git a/arch/arm/boot/dts/sun5i-a13-inet-98v-rev2.dts b/arch/arm/boot/dts/sun5i-a13-inet-98v-rev2.dts new file mode 100644 index 000000000000..6fa54b661423 --- /dev/null +++ b/arch/arm/boot/dts/sun5i-a13-inet-98v-rev2.dts @@ -0,0 +1,227 @@ +/* + * Copyright 2015 Hans de Goede <hdegoede@redhat.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun5i-a13.dtsi" +#include "sunxi-common-regulators.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> + +/ { + model = "INet-98V Rev 02"; + compatible = "primux,inet98v-rev2", "allwinner,sun5i-a13"; + + aliases { + serial0 = &uart1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&ehci0 { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + reg = <0x34>; + interrupts = <0>; + }; +}; + +#include "axp209.dtsi" + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; + + pcf8563: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; +}; + +&lradc { + vref-supply = <®_ldo2>; + status = "okay"; + + button@200 { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + channel = <0>; + voltage = <200000>; + }; + + button@400 { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + channel = <0>; + voltage = <400000>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_inet98fv2>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */ + cd-inverted; + status = "okay"; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_a>; + vmmc-supply = <®_vcc3v3>; + bus-width = <8>; + non-removable; + status = "okay"; + + mmccard: mmccard@0 { + reg = <0>; + compatible = "mmc-card"; + broken-hpi; + }; +}; + +&otg_sram { + status = "okay"; +}; + +&pio { + mmc0_cd_pin_inet98fv2: mmc0_cd_pin@0 { + allwinner,pins = "PG0"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PG1"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>; + }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PG2"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd-int-pll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_ldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +®_usb0_vbus { + gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins_b>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb0_vbus_pin_a { + allwinner,pins = "PG12"; +}; + +&usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */ + usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */ + usb0_vbus-supply = <®_usb0_vbus>; + usb1_vbus-supply = <®_ldo3>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun5i-a13-q8-tablet.dts b/arch/arm/boot/dts/sun5i-a13-q8-tablet.dts new file mode 100644 index 000000000000..72e93acb5a9e --- /dev/null +++ b/arch/arm/boot/dts/sun5i-a13-q8-tablet.dts @@ -0,0 +1,60 @@ +/* + * Copyright 2015 Hans de Goede <hdegoede@redhat.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun5i-a13.dtsi" +#include "sun5i-q8-common.dtsi" + +/ { + model = "Q8 A13 Tablet"; + compatible = "allwinner,q8-a13", "allwinner,sun5i-a13"; +}; + +®_ldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +&usbphy { + usb1_vbus-supply = <®_ldo3>; +}; diff --git a/arch/arm/boot/dts/sun5i-a13.dtsi b/arch/arm/boot/dts/sun5i-a13.dtsi index f3631c9c6fa2..d910d3a6c41c 100644 --- a/arch/arm/boot/dts/sun5i-a13.dtsi +++ b/arch/arm/boot/dts/sun5i-a13.dtsi @@ -150,6 +150,16 @@ "apb1_uart3"; }; }; + + soc@01c00000 { + pwm: pwm@01c20e00 { + compatible = "allwinner,sun5i-a13-pwm"; + reg = <0x01c20e00 0xc>; + clocks = <&osc24M>; + #pwm-cells = <3>; + status = "disabled"; + }; + }; }; &cpu0 { diff --git a/arch/arm/boot/dts/sun5i-q8-common.dtsi b/arch/arm/boot/dts/sun5i-q8-common.dtsi new file mode 100644 index 000000000000..a78e189f6653 --- /dev/null +++ b/arch/arm/boot/dts/sun5i-q8-common.dtsi @@ -0,0 +1,180 @@ +/* + * Copyright 2015 Hans de Goede <hdegoede@redhat.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +#include "sunxi-q8-common.dtsi" + +#include <dt-bindings/pwm/pwm.h> + +/ { + aliases { + serial0 = &uart1; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <8>; + /* TODO: backlight uses axp gpio1 as enable pin */ + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&ehci0 { + status = "okay"; +}; + +&i2c0 { + axp209: pmic@34 { + reg = <0x34>; + interrupts = <0>; + }; +}; + +&i2c1 { + pcf8563: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; +}; + +#include "axp209.dtsi" + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8>; + vmmc-supply = <®_vcc3v0>; + bus-width = <4>; + cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */ + cd-inverted; + status = "okay"; +}; + +&otg_sram { + status = "okay"; +}; + +&pio { + mmc0_cd_pin_q8: mmc0_cd_pin@0 { + allwinner,pins = "PG0"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PG1"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>; + }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PG2"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + usb0_vbus_pin_a: usb0_vbus_pin@0 { + allwinner,pins = "PG12"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-int-pll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_usb0_vbus { + gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins_b>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */ + usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */ + usb0_vbus-supply = <®_usb0_vbus>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun5i-r8-chip.dts b/arch/arm/boot/dts/sun5i-r8-chip.dts new file mode 100644 index 000000000000..530ab28e9ca2 --- /dev/null +++ b/arch/arm/boot/dts/sun5i-r8-chip.dts @@ -0,0 +1,218 @@ +/* + * Copyright 2015 Free Electrons + * Copyright 2015 NextThing Co + * + * Maxime Ripard <maxime.ripard@free-electrons.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun5i-r8.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + model = "NextThing C.H.I.P."; + compatible = "nextthing,chip", "allwinner,sun5i-r8"; + + aliases { + i2c0 = &i2c0; + i2c2 = &i2c2; + serial0 = &uart1; + serial1 = &uart3; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&codec { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + reg = <0x34>; + + /* + * The interrupt is routed through the "External Fast + * Interrupt Request" pin (ball G13 of the module) + * directly to the main interrupt controller, without + * any other controller interfering. + */ + interrupts = <0>; + }; +}; + +#include "axp209.dtsi" + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; + + xio: gpio@38 { + compatible = "nxp,pcf8574a"; + reg = <0x38>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-parent = <&pio>; + interrupts = <6 0 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&otg_sram { + status = "okay"; +}; + +&pio { + chip_vbus_pin: chip_vbus_pin@0 { + allwinner,pins = "PB10"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + chip_id_det_pin: chip_id_det_pin@0 { + allwinner,pins = "PG2"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; +}; + +®_dcdc2 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "cpuvdd"; + regulator-always-on; +}; + +®_dcdc3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-name = "corevdd"; + regulator-always-on; +}; + +®_ldo1 { + regulator-name = "rtcvdd"; +}; + +®_ldo2 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "avcc"; + regulator-always-on; +}; + +®_ldo5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-1v8"; +}; + +®_usb0_vbus { + pinctrl-0 = <&chip_vbus_pin>; + vin-supply = <®_vcc5v0>; + gpio = <&pio 1 10 GPIO_ACTIVE_HIGH>; /* PB10 */ + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins_b>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins_a>, + <&uart3_pins_cts_rts_a>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb_power_supply { + status = "okay"; +}; + +&usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&chip_id_det_pin>; + status = "okay"; + + usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb0_vbus-supply = <®_usb0_vbus>; + usb1_vbus-supply = <®_vcc5v0>; +}; diff --git a/arch/arm/boot/dts/sun5i-r8.dtsi b/arch/arm/boot/dts/sun5i-r8.dtsi new file mode 100644 index 000000000000..0ef865601ac9 --- /dev/null +++ b/arch/arm/boot/dts/sun5i-r8.dtsi @@ -0,0 +1,59 @@ +/* + * Copyright 2015 Free Electrons + * Copyright 2015 NextThing Co + * + * Maxime Ripard <maxime.ripard@free-electrons.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "sun5i-a13.dtsi" + +/ { + chosen { + framebuffer@1 { + compatible = "allwinner,simple-framebuffer", + "simple-framebuffer"; + allwinner,pipeline = "de_be0-lcd0-tve0"; + clocks = <&pll5 1>, <&ahb_gates 34>, <&ahb_gates 36>, + <&ahb_gates 44>; + status = "disabled"; + }; + }; +}; diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/sun5i.dtsi index 78b993abbaa3..59a9426e3bd4 100644 --- a/arch/arm/boot/dts/sun5i.dtsi +++ b/arch/arm/boot/dts/sun5i.dtsi @@ -44,6 +44,7 @@ #include "skeleton.dtsi" +#include <dt-bindings/clock/sun4i-a10-pll2.h> #include <dt-bindings/dma/sun4i-a10.h> #include <dt-bindings/pinctrl/sun4i-a10.h> @@ -102,6 +103,15 @@ clock-output-names = "pll1"; }; + pll2: clk@01c20008 { + #clock-cells = <1>; + compatible = "allwinner,sun5i-a13-pll2-clk"; + reg = <0x01c20008 0x8>; + clocks = <&osc24M>; + clock-output-names = "pll2-1x", "pll2-2x", + "pll2-4x", "pll2-8x"; + }; + pll4: clk@01c20018 { #clock-cells = <0>; compatible = "allwinner,sun4i-a10-pll1-clk"; @@ -285,6 +295,14 @@ clock-output-names = "usb_ohci0", "usb_phy"; }; + codec_clk: clk@01c20140 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-codec-clk"; + reg = <0x01c20140 0x4>; + clocks = <&pll2 SUN4I_A10_PLL2_1X>; + clock-output-names = "codec"; + }; + mbus_clk: clk@01c2015c { #clock-cells = <0>; compatible = "allwinner,sun5i-a13-mbus-clk"; @@ -529,6 +547,27 @@ allwinner,drive = <SUN4I_PINCTRL_30_MA>; allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; }; + + uart3_pins_a: uart3@0 { + allwinner,pins = "PG9", "PG10"; + allwinner,function = "uart3"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + uart3_pins_cts_rts_a: uart3-cts-rts@0 { + allwinner,pins = "PG11", "PG12"; + allwinner,function = "uart3"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + pwm0_pins: pwm0 { + allwinner,pins = "PB2"; + allwinner,function = "pwm"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; }; timer@01c20c00 { @@ -550,6 +589,19 @@ status = "disabled"; }; + codec: codec@01c22c00 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun4i-a10-codec"; + reg = <0x01c22c00 0x40>; + interrupts = <30>; + clocks = <&apb0_gates 0>, <&codec_clk>; + clock-names = "apb", "codec"; + dmas = <&dma SUN4I_DMA_NORMAL 19>, + <&dma SUN4I_DMA_NORMAL 19>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + sid: eeprom@01c23800 { compatible = "allwinner,sun4i-a10-sid"; reg = <0x01c23800 0x10>; diff --git a/arch/arm/boot/dts/sun6i-a31-colombus.dts b/arch/arm/boot/dts/sun6i-a31-colombus.dts index 0cf9926d1e93..f9cf36888d93 100644 --- a/arch/arm/boot/dts/sun6i-a31-colombus.dts +++ b/arch/arm/boot/dts/sun6i-a31-colombus.dts @@ -60,12 +60,34 @@ chosen { stdout-path = "serial0:115200n8"; }; + + i2c_lcd: i2c@0 { + /* The lcd panel i2c interface is hooked up via gpios */ + compatible = "i2c-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c_lcd_pins>; + gpios = <&pio 0 23 GPIO_ACTIVE_HIGH>, /* PA23, sda */ + <&pio 0 24 GPIO_ACTIVE_HIGH>; /* PA24, scl */ + i2c-gpio,delay-us = <5>; + }; }; &ehci1 { status = "okay"; }; +&gmac { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_rgmii_a>; + phy = <&phy1>; + phy-mode = "rgmii"; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + &i2c0 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins_a>; @@ -82,6 +104,13 @@ pinctrl-names = "default"; pinctrl-0 = <&i2c2_pins_a>; status = "okay"; + + mma8452: mma8452@1d { + compatible = "fsl,mma8452"; + reg = <0x1d>; + interrupt-parent = <&pio>; + interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PA9 */ + }; }; &mmc0 { @@ -112,6 +141,13 @@ allwinner,drive = <SUN4I_PINCTRL_10_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + + i2c_lcd_pins: i2c_lcd_pin@0 { + allwinner,pins = "PA23", "PA24"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; }; ®_usb2_vbus { diff --git a/arch/arm/boot/dts/sun6i-a31-hummingbird.dts b/arch/arm/boot/dts/sun6i-a31-hummingbird.dts index d0cfadac0691..9a74637f677f 100644 --- a/arch/arm/boot/dts/sun6i-a31-hummingbird.dts +++ b/arch/arm/boot/dts/sun6i-a31-hummingbird.dts @@ -54,6 +54,8 @@ compatible = "merrii,a31-hummingbird", "allwinner,sun6i-a31"; aliases { + rtc0 = &pcf8563; + rtc1 = &rtc; serial0 = &uart0; }; @@ -67,13 +69,17 @@ }; }; +&cpu0 { + cpu-supply = <®_dcdc3>; +}; + &ehci0 { status = "okay"; }; &gmac { pinctrl-names = "default"; - pinctrl-0 = <&gmac_pins_rgmii_a>; + pinctrl-0 = <&gmac_pins_rgmii_a>, <&gmac_phy_reset_pin_hummingbird>; phy = <&phy1>; phy-mode = "rgmii"; snps,reset-gpio = <&pio 0 21 GPIO_ACTIVE_HIGH>; @@ -119,7 +125,7 @@ &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_hummingbird>; - vmmc-supply = <&vcc_3v0>; + vmmc-supply = <®_dcdc1>; bus-width = <4>; cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */ cd-inverted; @@ -134,7 +140,7 @@ &mmc1 { pinctrl-names = "default"; pinctrl-0 = <&mmc1_pins_a>, <&wifi_reset_pin_hummingbird>; - vmmc-supply = <&vcc_wifi>; + vmmc-supply = <®_aldo1>; mmc-pwrseq = <&wifi_pwrseq>; bus-width = <4>; non-removable; @@ -146,6 +152,13 @@ }; &pio { + gmac_phy_reset_pin_hummingbird: gmac_phy_reset_pin@0 { + allwinner,pins = "PA21"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + mmc0_cd_pin_hummingbird: mmc0_cd_pin@0 { allwinner,pins = "PA8"; allwinner,function = "gpio_in"; @@ -164,70 +177,69 @@ &p2wi { status = "okay"; - axp221: pmic@68 { + axp22x: pmic@68 { compatible = "x-powers,axp221"; reg = <0x68>; interrupt-parent = <&nmi_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #interrupt-cells = <1>; - dcdc1-supply = <&vcc_3v0>; - dcdc5-supply = <&vcc_dram>; - - regulators { - x-powers,dcdc-freq = <3000>; - - vcc_3v0: dcdc1 { - regulator-always-on; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - regulator-name = "vcc-3v0"; - }; - - vdd_cpu: dcdc2 { - regulator-always-on; - regulator-min-microvolt = <700000>; - regulator-max-microvolt = <1320000>; - regulator-name = "vdd-cpu"; - }; - - vdd_gpu: dcdc3 { - regulator-always-on; - regulator-min-microvolt = <700000>; - regulator-max-microvolt = <1320000>; - regulator-name = "vdd-gpu"; - }; - - vdd_sys_dll: dcdc4 { - regulator-always-on; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-name = "vdd-sys-dll"; - }; - - vcc_dram: dcdc5 { - regulator-always-on; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - regulator-name = "vcc-dram"; - }; - - vcc_wifi: aldo1 { - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-name = "vcc_wifi"; - }; - - avcc: aldo3 { - regulator-always-on; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - regulator-name = "avcc"; - }; - }; }; }; +#include "axp22x.dtsi" + +®_aldo1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "avcc"; +}; + +®_dc5ldo { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-cpus"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-3v0"; +}; + +®_dcdc2 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc4 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-sys-dll"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vcc-dram"; +}; + ®_usb1_vbus { gpio = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */ status = "okay"; diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi index 54bb83b58f42..b6ad7850fac6 100644 --- a/arch/arm/boot/dts/sun6i-a31.dtsi +++ b/arch/arm/boot/dts/sun6i-a31.dtsi @@ -61,7 +61,7 @@ #size-cells = <1>; ranges; - framebuffer@0 { + simplefb_hdmi: framebuffer@0 { compatible = "allwinner,simple-framebuffer", "simple-framebuffer"; allwinner,pipeline = "de_be0-lcd0-hdmi"; @@ -69,7 +69,7 @@ status = "disabled"; }; - framebuffer@1 { + simplefb_lcd: framebuffer@1 { compatible = "allwinner,simple-framebuffer", "simple-framebuffer"; allwinner,pipeline = "de_be0-lcd0"; @@ -691,6 +691,24 @@ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + mmc2_pins_a: mmc2@0 { + allwinner,pins = "PC6", "PC7", "PC8", "PC9", + "PC10", "PC11"; + allwinner,function = "mmc2"; + allwinner,drive = <SUN4I_PINCTRL_30_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + mmc2_8bit_emmc_pins: mmc2@1 { + allwinner,pins = "PC6", "PC7", "PC8", "PC9", + "PC10", "PC11", "PC12", + "PC13", "PC14", "PC15", + "PC24"; + allwinner,function = "mmc2"; + allwinner,drive = <SUN4I_PINCTRL_30_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + gmac_pins_mii_a: gmac_mii@0 { allwinner,pins = "PA0", "PA1", "PA2", "PA3", "PA8", "PA9", "PA11", @@ -768,6 +786,13 @@ reg = <0x01c20ca0 0x20>; }; + lradc: lradc@01c22800 { + compatible = "allwinner,sun4i-a10-lradc-keys"; + reg = <0x01c22800 0x100>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + rtp: rtp@01c25000 { compatible = "allwinner,sun6i-a31-ts"; reg = <0x01c25000 0x100>; @@ -1085,7 +1110,7 @@ resets = <&apb0_rst 0>; gpio-controller; interrupt-controller; - #interrupt-cells = <2>; + #interrupt-cells = <3>; #size-cells = <0>; #gpio-cells = <3>; diff --git a/arch/arm/boot/dts/sun6i-a31s-primo81.dts b/arch/arm/boot/dts/sun6i-a31s-primo81.dts new file mode 100644 index 000000000000..2d4250b1faf8 --- /dev/null +++ b/arch/arm/boot/dts/sun6i-a31s-primo81.dts @@ -0,0 +1,255 @@ +/* + * Copyright 2014 Siarhei Siamashka <siarhei.siamashka@gmail.com> + * Copyright 2015 Karsten Merker <merker@debian.org> + * Copyright 2015 Chen-Yu Tsai <wens@csie.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun6i-a31s.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> + +/ { + model = "MSI Primo81 tablet"; + compatible = "msi,primo81", "allwinner,sun6i-a31s"; +}; + +&cpu0 { + cpu-supply = <®_dcdc3>; +}; + +&ehci0 { + /* rtl8188etv wifi is connected here */ + status = "okay"; +}; + +&i2c0 { + /* pull-ups and device VDDIO use AXP221 DLDO3 */ + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "failed"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; + + ctp@5d { + pinctrl-names = "default"; + pinctrl-0 = <>911_int_primo81>; + compatible = "goodix,gt911"; + reg = <0x5d>; + interrupt-parent = <&pio>; + interrupts = <0 3 IRQ_TYPE_LEVEL_HIGH>; /* PA3 */ + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; + + accelerometer@1c { + pinctrl-names = "default"; + pinctrl-0 = <&mma8452_int_primo81>; + compatible = "fsl,mma8452"; + reg = <0x1c>; + interrupt-parent = <&pio>; + interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>; /* PA9 */ + #io-channel-cells = <1>; + }; +}; + +&lradc { + vref-supply = <®_aldo3>; + status = "okay"; + + button@158 { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + channel = <0>; + voltage = <158730>; + }; + + button@349 { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + channel = <0>; + voltage = <349206>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_primo81>; + vmmc-supply = <®_dcdc1>; + bus-width = <4>; + cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */ + cd-inverted; + status = "okay"; +}; + +&pio { + gt911_int_primo81: gt911_int_pin@0 { + allwinner,pins = "PA3"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + mma8452_int_primo81: mma8452_int_pin@0 { + allwinner,pins = "PA9"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + mmc0_cd_pin_primo81: mmc0_cd_pin@0 { + allwinner,pins = "PA8"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; +}; + +&p2wi { + status = "okay"; + + axp22x: pmic@68 { + compatible = "x-powers,axp221"; + reg = <0x68>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +#include "axp22x.dtsi" + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "avcc"; +}; + +®_dc1sw { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-lcd"; +}; + +®_dc5ldo { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-cpus"; /* This is an educated guess */ +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-3v0"; +}; + +®_dcdc2 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc4 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-sys-dll"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vcc-dram"; +}; + +®_dldo1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +®_dldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "vddio-csi"; +}; + +®_eldo3 { + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-mipi-bridge"; +}; + +&simplefb_lcd { + vcc-lcd-supply = <®_dc1sw>; + vdd-mipi-bridge-supply = <®_eldo3>; +}; + +&usb_otg { + /* otg support requires support for AXP221 usb-power-supply and GPIO */ + dr_mode = "host"; + status = "okay"; +}; + +&usbphy { + usb1_vbus-supply = <®_dldo1>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi b/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi new file mode 100644 index 000000000000..ea69fb8ad4d8 --- /dev/null +++ b/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi @@ -0,0 +1,140 @@ +/* + * Copyright 2015 Chen-Yu Tsai <wens@csie.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun6i-a31s.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> + +/ { + model = "Sinlinx SinA31s Core Board"; + compatible = "sinlinx,sina31s", "allwinner,sun6i-a31s"; + + aliases { + serial0 = &uart0; + }; +}; + +&cpu0 { + cpu-supply = <®_dcdc3>; +}; + +/* eMMC on core board */ +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_8bit_emmc_pins>; + vmmc-supply = <®_dcdc1>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +/* AXP221s PMIC on core board */ +&p2wi { + status = "okay"; + + axp22x: pmic@68 { + compatible = "x-powers,axp221"; + reg = <0x68>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +#include "axp22x.dtsi" + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "avcc"; +}; + +®_dc5ldo { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-cpus"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-3v0"; +}; + +®_dcdc2 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc4 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-sys-dll"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vcc-dram"; +}; + +/* UART0 pads available on core board */ +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + diff --git a/arch/arm/boot/dts/sun6i-a31s-sina31s.dts b/arch/arm/boot/dts/sun6i-a31s-sina31s.dts new file mode 100644 index 000000000000..6ead2f5c847a --- /dev/null +++ b/arch/arm/boot/dts/sun6i-a31s-sina31s.dts @@ -0,0 +1,153 @@ +/* + * Copyright 2015 Chen-Yu Tsai <wens@csie.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/* The SinA31s development board has the SinA31s core board soldered on */ +#include "sun6i-a31s-sina31s-core.dtsi" + +#include <dt-bindings/input/input.h> + +/ { + model = "Sinlinx SinA31s Development Board"; + compatible = "sinlinx,sina31s-sdk", "allwinner,sun6i-a31s"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pin_sina31s>; + + status { + label = "sina31s:status:usr"; + gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */ + }; + }; +}; + +&ehci0 { + /* USB 2.0 4 port hub IC */ + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&gmac { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_mii_a>; + phy = <&phy1>; + phy-mode = "mii"; + phy-supply = <®_dldo1>; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + +&ir { + pinctrl-names = "default"; + pinctrl-0 = <&ir_pins_a>; + status = "okay"; +}; + +&lradc { + vref-supply = <®_aldo3>; + status = "okay"; + + button@158 { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + channel = <0>; + voltage = <158730>; + }; + + button@349 { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + channel = <0>; + voltage = <349206>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_sina31s>; + vmmc-supply = <®_dcdc1>; + bus-width = <4>; + cd-gpios = <&pio 0 4 GPIO_ACTIVE_HIGH>; /* PA4 */ + cd-inverted; + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&pio { + led_pin_sina31s: led_pin@0 { + allwinner,pins = "PH13"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + mmc0_cd_pin_sina31s: mmc0_cd_pin@0 { + allwinner,pins = "PA4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; +}; + +®_dldo1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-gmac-phy"; +}; + +&usbphy { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts b/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts new file mode 100644 index 000000000000..db7fa13f5425 --- /dev/null +++ b/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts @@ -0,0 +1,194 @@ +/* + * Copyright 2015 Hans de Goede <hdegoede@redhat.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun6i-a31s.dtsi" +#include "sunxi-common-regulators.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Sinovoip BPI-M2"; + compatible = "sinovoip,bpi-m2", "allwinner,sun6i-a31s"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_bpi_m2>; + + blue { + label = "bpi-m2:blue:usr"; + gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */ + }; + + green { + label = "bpi-m2:green:usr"; + gpios = <&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10 */ + }; + + red { + label = "bpi-m2:red:usr"; + gpios = <&pio 6 5 GPIO_ACTIVE_HIGH>; /* PG5 */ + }; + }; + + mmc2_pwrseq: mmc2_pwrseq { + compatible = "mmc-pwrseq-simple"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pwrseq_pin_bpi_m2>; + reset-gpios = <&r_pio 0 8 GPIO_ACTIVE_LOW>; /* PL8 WIFI_EN */ + }; +}; + +&ehci0 { + status = "okay"; +}; + +&gmac { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_rgmii_a>, <&gmac_phy_reset_pin_bpi_m2>; + phy = <&phy1>; + phy-mode = "rgmii"; + snps,reset-gpio = <&pio 0 21 GPIO_ACTIVE_HIGH>; /* PA21 */ + snps,reset-active-low; + snps,reset-delays-us = <0 10000 30000>; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + +&ir { + pinctrl-names = "default"; + pinctrl-0 = <&ir_pins_a>; + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_m2>; + vmmc-supply = <®_vcc3v0>; + bus-width = <4>; + cd-gpios = <&pio 0 4 GPIO_ACTIVE_HIGH>; /* PA4 */ + cd-inverted; + status = "okay"; +}; + +&mmc0_pins_a { + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_a>; + vmmc-supply = <®_vcc3v0>; + mmc-pwrseq = <&mmc2_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&r_pio>; + interrupts = <0 5 IRQ_TYPE_LEVEL_LOW>; /* PL5 */ + interrupt-names = "host-wake"; + }; +}; + +&mmc2_pins_a { + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; +}; + +&ohci0 { + status = "okay"; +}; + +&pio { + gmac_phy_reset_pin_bpi_m2: gmac_phy_reset_pin@0 { + allwinner,pins = "PA21"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + led_pins_bpi_m2: led_pins@0 { + allwinner,pins = "PG5", "PG10", "PG11"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + mmc0_cd_pin_bpi_m2: mmc0_cd_pin@0 { + allwinner,pins = "PA4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; +}; + +&r_pio { + mmc2_pwrseq_pin_bpi_m2: mmc2_pwrseq_pin@0 { + allwinner,pins = "PL8"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts b/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts new file mode 100644 index 000000000000..b199020733d3 --- /dev/null +++ b/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts @@ -0,0 +1,134 @@ +/* + * Copyright 2015 Lawrence Yu <lyu@micile.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun6i-a31s.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> + +/ { + model = "Yones TopTech BS1078 v2 Tablet"; + compatible = "yones-toptech,bs1078-v2", "allwinner,sun6i-a31s"; + + aliases { + serial0 = &uart0; + i2c1 = &i2c1; + i2c2 = &i2c2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&pio { + mmc0_cd_pin_bs1078v2: mmc0_cd_pin@0 { + allwinner,pins = "PA8"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bs1078v2>; + vmmc-supply = <®_vcc3v0>; + bus-width = <4>; + cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */ + cd-inverted; + status = "okay"; +}; + +&mmc0_pins_a { + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; +}; + +®_usb1_vbus { + gpio = <&pio 7 27 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&usb1_vbus_pin_a { + allwinner,pins = "PH27"; +}; + +&usbphy { + usb1_vbus-supply = <®_usb1_vbus>; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi.dts b/arch/arm/boot/dts/sun7i-a20-bananapi.dts index 9f7b472e6725..fd7594ff90d5 100644 --- a/arch/arm/boot/dts/sun7i-a20-bananapi.dts +++ b/arch/arm/boot/dts/sun7i-a20-bananapi.dts @@ -92,6 +92,20 @@ status = "okay"; }; +&cpu0 { + cpu-supply = <®_dcdc2>; + operating-points = < + /* kHz uV */ + 960000 1400000 + 912000 1400000 + 864000 1350000 + 720000 1250000 + 528000 1150000 + 312000 1100000 + 144000 1050000 + >; +}; + &ehci0 { status = "okay"; }; @@ -119,13 +133,9 @@ status = "okay"; axp209: pmic@34 { - compatible = "x-powers,axp209"; reg = <0x34>; interrupt-parent = <&nmi_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - - interrupt-controller; - #interrupt-cells = <1>; }; }; @@ -159,7 +169,18 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + mmc0_cd_pin_bananapi: mmc0_cd_pin@0 { allwinner,pins = "PH10"; allwinner,function = "gpio_in"; @@ -182,6 +203,37 @@ }; }; +#include "axp209.dtsi" + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-int-dll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_usb0_vbus { + status = "okay"; +}; + ®_usb1_vbus { status = "okay"; }; @@ -216,7 +268,21 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb_power_supply { + status = "okay"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; diff --git a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts b/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts index 39a51d5143f7..1fa832d7b469 100644 --- a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts +++ b/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts @@ -84,6 +84,10 @@ status = "okay"; }; +&codec { + status = "okay"; +}; + &cpu0 { cpu-supply = <®_dcdc2>; }; @@ -150,6 +154,10 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { led_pins_cubieboard2: led_pins@0 { allwinner,pins = "PH20", "PH21"; @@ -157,12 +165,24 @@ allwinner,drive = <SUN4I_PINCTRL_10_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; }; ®_ahci_5v { status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + #include "axp209.dtsi" ®_dcdc2 { @@ -205,6 +225,9 @@ }; &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts index e6b019232a9e..8da939ab8350 100644 --- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts +++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts @@ -101,6 +101,10 @@ status = "okay"; }; +&codec { + status = "okay"; +}; + &cpu0 { cpu-supply = <®_dcdc2>; }; diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts b/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts new file mode 100644 index 000000000000..b7fe102475e7 --- /dev/null +++ b/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts @@ -0,0 +1,198 @@ +/* + * Copyright 2015 - Marcus Cooper <codekipper@gmail.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun7i-a20.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> + +/ { + model = "Olimex A20-Olimex-SOM-EVB"; + compatible = "olimex,a20-olimex-som-evb", "allwinner,sun7i-a20"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_olimex_som_evb>; + + green { + label = "a20-olimex-som-evb:green:usr"; + gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; +}; + +&ahci { + target-supply = <®_ahci_5v>; + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&gmac { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_rgmii_a>; + phy = <&phy1>; + phy-mode = "rgmii"; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ + cd-inverted; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&pio { + ahci_pwr_pin_olimex_som_evb: ahci_pwr_pin@1 { + allwinner,pins = "PC3"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + led_pins_olimex_som_evb: led_pins@0 { + allwinner,pins = "PH2"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_20_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; +}; + +®_ahci_5v { + pinctrl-0 = <&ahci_pwr_pin_olimex_som_evb>; + gpio = <&pio 2 3 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +#include "axp209.dtsi" + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-int-dll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_usb1_vbus { + status = "okay"; +}; + +®_usb2_vbus { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usbphy { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts index 04237085dc39..35ad7006c53c 100644 --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts @@ -117,6 +117,18 @@ }; }; +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; + + eeprom: eeprom@50 { + compatible = "atmel,24c16"; + reg = <0x50>; + pagesize = <16>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts index 8acff78272b7..d5c796c8d16f 100644 --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts @@ -170,6 +170,12 @@ pinctrl-names = "default"; pinctrl-0 = <&i2c1_pins_a>; status = "okay"; + + eeprom: eeprom@50 { + compatible = "atmel,24c16"; + reg = <0x50>; + pagesize = <16>; + }; }; &mmc0 { @@ -190,6 +196,10 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { ahci_pwr_pin_olinuxinolime: ahci_pwr_pin@1 { allwinner,pins = "PC3"; @@ -204,6 +214,27 @@ allwinner,drive = <SUN4I_PINCTRL_20_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PH5"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>; + }; + + usb0_vbus_pin_lime2: usb0_vbus_pin@0 { + allwinner,pins = "PC17"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; }; ®_ahci_5v { @@ -212,6 +243,12 @@ status = "okay"; }; +®_usb0_vbus { + pinctrl-0 = <&usb0_vbus_pin_lime2>; + gpio = <&pio 2 17 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + ®_usb1_vbus { status = "okay"; }; @@ -226,7 +263,17 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */ + usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts index c5d70caade82..7e3006f6a775 100644 --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts @@ -125,6 +125,12 @@ pinctrl-names = "default"; pinctrl-0 = <&i2c1_pins_a>; status = "okay"; + + eeprom: eeprom@50 { + compatible = "atmel,24c16"; + reg = <0x50>; + pagesize = <16>; + }; }; &i2c2 { diff --git a/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts b/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts index 73cd81ee02e3..4f65664e5dfe 100644 --- a/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts +++ b/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts @@ -156,7 +156,18 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + mmc0_cd_pin_orangepi: mmc0_cd_pin@0 { allwinner,pins = "PH10"; allwinner,function = "gpio_in"; @@ -225,6 +236,10 @@ regulator-name = "avcc"; }; +®_usb0_vbus { + status = "okay"; +}; + ®_usb1_vbus { pinctrl-0 = <&usb1_vbus_pin_bananapro>; gpio = <&pio 7 26 GPIO_ACTIVE_HIGH>; /* PH26 */ @@ -243,7 +258,21 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb_power_supply { + status = "okay"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; diff --git a/arch/arm/boot/dts/sun7i-a20-orangepi.dts b/arch/arm/boot/dts/sun7i-a20-orangepi.dts index 55a06ceb80ec..71125bf64575 100644 --- a/arch/arm/boot/dts/sun7i-a20-orangepi.dts +++ b/arch/arm/boot/dts/sun7i-a20-orangepi.dts @@ -141,7 +141,18 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + mmc0_cd_pin_orangepi: mmc0_cd_pin@0 { allwinner,pins = "PH10"; allwinner,function = "gpio_in"; @@ -203,6 +214,10 @@ regulator-name = "avcc"; }; +®_usb0_vbus { + status = "okay"; +}; + ®_usb1_vbus { pinctrl-0 = <&usb1_vbus_pin_bananapro>; gpio = <&pio 7 26 GPIO_ACTIVE_HIGH>; /* PH26 */ @@ -221,7 +236,21 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb_power_supply { + status = "okay"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; diff --git a/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts b/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts index 5361fce26b45..1757a6ad74e9 100644 --- a/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts +++ b/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts @@ -82,6 +82,10 @@ status = "okay"; }; +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + &ehci0 { status = "okay"; }; @@ -108,13 +112,9 @@ status = "okay"; axp209: pmic@34 { - compatible = "x-powers,axp209"; reg = <0x34>; interrupt-parent = <&nmi_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - - interrupt-controller; - #interrupt-cells = <1>; }; }; @@ -142,6 +142,10 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { ahci_pwr_pin_pcduino3_nano: ahci_pwr_pin@0 { allwinner,pins = "PH2"; @@ -157,8 +161,15 @@ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + usb1_vbus_pin_pcduino3_nano: usb1_vbus_pin@0 { - allwinner,pins = "PH11"; + allwinner,pins = "PD2"; allwinner,function = "gpio_out"; allwinner,drive = <SUN4I_PINCTRL_10_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; @@ -171,13 +182,37 @@ status = "okay"; }; -®_usb1_vbus { - pinctrl-0 = <&usb1_vbus_pin_pcduino3_nano>; - gpio = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */ - status = "okay"; +#include "axp209.dtsi" + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; }; -®_usb2_vbus { +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-int-pll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +/* A single regulator (U24) powers both USB host ports. */ +®_usb1_vbus { + pinctrl-0 = <&usb1_vbus_pin_pcduino3_nano>; + gpio = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */ status = "okay"; }; @@ -187,8 +222,16 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ usb1_vbus-supply = <®_usb1_vbus>; - usb2_vbus-supply = <®_usb2_vbus>; + usb2_vbus-supply = <®_usb1_vbus>; status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-pcduino3.dts b/arch/arm/boot/dts/sun7i-a20-pcduino3.dts index afc9ecebed21..861a4a66fb19 100644 --- a/arch/arm/boot/dts/sun7i-a20-pcduino3.dts +++ b/arch/arm/boot/dts/sun7i-a20-pcduino3.dts @@ -111,6 +111,10 @@ allwinner,pins = "PH2"; }; +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + &ehci0 { status = "okay"; }; @@ -137,16 +141,14 @@ status = "okay"; axp209: pmic@34 { - compatible = "x-powers,axp209"; reg = <0x34>; interrupt-parent = <&nmi_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - - interrupt-controller; - #interrupt-cells = <1>; }; }; +#include "axp209.dtsi" + &ir0 { pinctrl-names = "default"; pinctrl-0 = <&ir0_rx_pins_a>; @@ -171,6 +173,10 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { led_pins_pcduino3: led_pins@0 { allwinner,pins = "PH15", "PH16"; @@ -185,6 +191,13 @@ allwinner,drive = <SUN4I_PINCTRL_10_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; }; ®_ahci_5v { @@ -192,6 +205,31 @@ status = "okay"; }; +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-int-pll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + ®_usb1_vbus { status = "okay"; }; @@ -206,7 +244,15 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts index 83c6d3f872ff..78239ad988e7 100644 --- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts +++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts @@ -86,6 +86,8 @@ }; }; +#include "axp209.dtsi" + &i2c1 { pinctrl-names = "default"; pinctrl-0 = <&i2c1_pins_a>; @@ -135,7 +137,18 @@ status = "okay"; }; -#include "axp209.dtsi" +&otg_sram { + status = "okay"; +}; + +&pio { + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; +}; ®_dcdc2 { regulator-always-on; @@ -162,6 +175,10 @@ regulator-name = "avcc"; }; +®_usb0_vbus { + status = "okay"; +}; + ®_usb1_vbus { status = "okay"; }; @@ -176,7 +193,21 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb_power_supply { + status = "okay"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; diff --git a/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts b/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts new file mode 100644 index 000000000000..85b500d8cc4c --- /dev/null +++ b/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts @@ -0,0 +1,226 @@ +/* + * Copyright 2015 Jelle de Jong <jelledejong@powercraft.nl> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun7i-a20.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + model = "Wits Pro A20 DKT"; + compatible = "wits,pro-a20-dkt", "allwinner,sun7i-a20"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + mmc3_pwrseq: mmc3_pwrseq { + compatible = "mmc-pwrseq-simple"; + pinctrl-names = "default"; + pinctrl-0 = <&vmmc3_pin_ap6xxx_wl_regon>; + reset-gpios = <&pio 7 9 GPIO_ACTIVE_LOW>; /* PH9 WIFI_EN */ + }; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; +}; + +#include "axp209.dtsi" + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ + cd-inverted; + status = "okay"; +}; + +&mmc3 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins_a>; + vmmc-supply = <®_vcc3v3>; + mmc-pwrseq = <&mmc3_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&pio>; + interrupts = <7 10 IRQ_TYPE_LEVEL_LOW>; /* PH10 / EINT10 */ + interrupt-names = "host-wake"; + }; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&otg_sram { + status = "okay"; +}; + +&pio { + vmmc3_pin_ap6xxx_wl_regon: vmmc3_pin@0 { + allwinner,pins = "PH9"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1450000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-int-dll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_usb0_vbus { + status = "okay"; +}; + +®_usb1_vbus { + status = "okay"; +}; + +®_usb2_vbus { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb_power_supply { + status = "okay"; +}; + +&usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb0_vbus-supply = <®_usb0_vbus>; + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi index 391230c3dc93..e02eb720c4fc 100644 --- a/arch/arm/boot/dts/sun7i-a20.dtsi +++ b/arch/arm/boot/dts/sun7i-a20.dtsi @@ -47,6 +47,7 @@ #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/thermal/thermal.h> +#include <dt-bindings/clock/sun4i-a10-pll2.h> #include <dt-bindings/dma/sun4i-a10.h> #include <dt-bindings/pinctrl/sun4i-a10.h> @@ -199,6 +200,15 @@ clock-output-names = "pll1"; }; + pll2: clk@01c20008 { + #clock-cells = <1>; + compatible = "allwinner,sun4i-a10-pll2-clk"; + reg = <0x01c20008 0x8>; + clocks = <&osc24M>; + clock-output-names = "pll2-1x", "pll2-2x", + "pll2-4x", "pll2-8x"; + }; + pll4: clk@01c20018 { #clock-cells = <0>; compatible = "allwinner,sun7i-a20-pll4-clk"; @@ -465,6 +475,14 @@ clock-output-names = "ir1"; }; + keypad_clk: clk@01c200c4 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c200c4 0x4>; + clocks = <&osc24M>; + clock-output-names = "keypad"; + }; + usb_clk: clk@01c200cc { #clock-cells = <1>; #reset-cells = <1>; @@ -483,6 +501,14 @@ clock-output-names = "spi3"; }; + codec_clk: clk@01c20140 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-codec-clk"; + reg = <0x01c20140 0x4>; + clocks = <&pll2 SUN4I_A10_PLL2_1X>; + clock-output-names = "codec"; + }; + mbus_clk: clk@01c2015c { #clock-cells = <0>; compatible = "allwinner,sun5i-a13-mbus-clk"; @@ -1190,6 +1216,19 @@ status = "disabled"; }; + codec: codec@01c22c00 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun7i-a20-codec"; + reg = <0x01c22c00 0x40>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&apb0_gates 0>, <&codec_clk>; + clock-names = "apb", "codec"; + dmas = <&dma SUN4I_DMA_NORMAL 19>, + <&dma SUN4I_DMA_NORMAL 19>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + sid: eeprom@01c23800 { compatible = "allwinner,sun7i-a20-sid"; reg = <0x01c23800 0x200>; diff --git a/arch/arm/boot/dts/sun8i-a23-a33.dtsi b/arch/arm/boot/dts/sun8i-a23-a33.dtsi index 27a925ec17d2..0c0964d4fa1f 100644 --- a/arch/arm/boot/dts/sun8i-a23-a33.dtsi +++ b/arch/arm/boot/dts/sun8i-a23-a33.dtsi @@ -175,31 +175,6 @@ clock-output-names = "apb1"; }; - ahb1_gates: clk@01c20060 { - #clock-cells = <1>; - compatible = "allwinner,sun8i-a23-ahb1-gates-clk"; - reg = <0x01c20060 0x8>; - clocks = <&ahb1>; - clock-indices = <1>, <6>, - <8>, <9>, <10>, - <13>, <14>, - <19>, <20>, - <21>, <24>, <26>, - <29>, <32>, <36>, - <40>, <44>, <46>, - <52>, <54>, - <57>; - clock-output-names = "ahb1_mipidsi", "ahb1_dma", - "ahb1_mmc0", "ahb1_mmc1", "ahb1_mmc2", - "ahb1_nand", "ahb1_sdram", - "ahb1_hstimer", "ahb1_spi0", - "ahb1_spi1", "ahb1_otg", "ahb1_ehci", - "ahb1_ohci", "ahb1_ve", "ahb1_lcd", - "ahb1_csi", "ahb1_be", "ahb1_fe", - "ahb1_gpu", "ahb1_spinlock", - "ahb1_drc"; - }; - apb1_gates: clk@01c20068 { #clock-cells = <1>; compatible = "allwinner,sun8i-a23-apb1-gates-clk"; @@ -412,6 +387,13 @@ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + pwm0_pins: pwm0 { + allwinner,pins = "PH0"; + allwinner,function = "pwm0"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + i2c0_pins_a: i2c0@0 { allwinner,pins = "PH2", "PH3"; allwinner,function = "i2c0"; @@ -466,6 +448,14 @@ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; }; + pwm: pwm@01c21400 { + compatible = "allwinner,sun7i-a20-pwm"; + reg = <0x01c21400 0xc>; + clocks = <&osc24M>; + #pwm-cells = <3>; + status = "disabled"; + }; + lradc: lradc@01c22800 { compatible = "allwinner,sun4i-a10-lradc-keys"; reg = <0x01c22800 0x100>; @@ -589,6 +579,14 @@ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; }; + nmi_intc: interrupt-controller@01f00c0c { + compatible = "allwinner,sun6i-a31-sc-nmi"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x01f00c0c 0x38>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + }; + prcm@01f01400 { compatible = "allwinner,sun8i-a23-prcm"; reg = <0x01f01400 0x200>; @@ -657,10 +655,18 @@ resets = <&apb0_rst 0>; gpio-controller; interrupt-controller; + #interrupt-cells = <3>; #address-cells = <1>; #size-cells = <0>; #gpio-cells = <3>; + r_rsb_pins: r_rsb { + allwinner,pins = "PL0", "PL1"; + allwinner,function = "s_rsb"; + allwinner,drive = <SUN4I_PINCTRL_20_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + r_uart_pins_a: r_uart@0 { allwinner,pins = "PL2", "PL3"; allwinner,function = "s_uart"; @@ -668,5 +674,19 @@ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; }; + + r_rsb: rsb@01f03400 { + compatible = "allwinner,sun8i-a23-rsb"; + reg = <0x01f03400 0x400>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&apb0_gates 3>; + clock-frequency = <3000000>; + resets = <&apb0_rst 3>; + pinctrl-names = "default"; + pinctrl-0 = <&r_rsb_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; }; }; diff --git a/arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts b/arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts new file mode 100644 index 000000000000..1aeb06c649b9 --- /dev/null +++ b/arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts @@ -0,0 +1,145 @@ +/* + * Copyright 2015 Hans de Goede <hdegoede@redhat.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun8i-a23.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> + +/ { + model = "Allwinner GT90H Quad Core Tablet (v4)"; + compatible = "allwinner,gt90h-v4", "allwinner,sun8i-a33"; + + aliases { + serial0 = &r_uart; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&ehci0 { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; +}; + +&lradc { + vref-supply = <®_vcc3v0>; + status = "okay"; + + button@200 { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + channel = <0>; + voltage = <200000>; + }; + + button@400 { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + channel = <0>; + voltage = <400000>; + }; + + button@600 { + label = "Back"; + linux,code = <KEY_BACK>; + channel = <0>; + voltage = <600000>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_gt90h>; + /* FIXME this really is aldo1, correct once we've pmic support */ + vmmc-supply = <®_vcc3v0>; + bus-width = <4>; + cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */ + cd-inverted; + status = "okay"; +}; + +&pio { + mmc0_cd_pin_gt90h: mmc0_cd_pin@0 { + allwinner,pins = "PB4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; +}; + +&r_uart { + pinctrl-names = "default"; + pinctrl-0 = <&r_uart_pins_a>; + status = "okay"; +}; + +/* + * FIXME for now we only support host mode and rely on u-boot to have + * turned on Vbus which is controlled by the axp223 pmic on the board. + * + * Once we have axp223 support we should switch to fully supporting otg. + */ +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v1.2.dts b/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v1.2.dts index 382d64c3b78e..c2f22fc33811 100644..120000 --- a/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v1.2.dts +++ b/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v1.2.dts @@ -1,54 +1 @@ -/* - * Copyright 2015 Hans de Goede <hdegoede@redhat.com> - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This file is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ - -/* - * The Ippo Q8H v1.2 is almost identical to the v5, still it needs a separate - * dtb file since some gpio-s surrounding the wlan/bluetooth are different, - * and it uses different camera sensors. - */ - -#include "sun8i-a23-ippo-q8h-v5.dts" - -/ { - model = "Ippo Q8H Dual Core Tablet (v1.2)"; - compatible = "ippo,q8h-v1.2", "allwinner,sun8i-a23"; -}; +sun8i-a23-q8-tablet.dts
\ No newline at end of file diff --git a/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v5.dts b/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v5.dts index 8d9da6886a4c..c2f22fc33811 100644..120000 --- a/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v5.dts +++ b/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v5.dts @@ -1,136 +1 @@ -/* - * Copyright 2014 Chen-Yu Tsai - * - * Chen-Yu Tsai <wens@csie.org> - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This file is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ - -/dts-v1/; -#include "sun8i-a23.dtsi" -#include "sunxi-common-regulators.dtsi" - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> -#include <dt-bindings/pinctrl/sun4i-a10.h> - -/ { - model = "Ippo Q8H Dual Core Tablet (v5)"; - compatible = "ippo,q8h-v5", "allwinner,sun8i-a23"; - - aliases { - serial0 = &r_uart; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; -}; - -&i2c0 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins_a>; - status = "okay"; -}; - -&i2c1 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins_a>; - status = "okay"; -}; - -&i2c2 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c2_pins_a>; - /* pull-ups and devices require PMIC regulator */ - status = "failed"; -}; - -&lradc { - vref-supply = <®_vcc3v0>; - status = "okay"; - - button@200 { - label = "Volume Up"; - linux,code = <KEY_VOLUMEUP>; - channel = <0>; - voltage = <200000>; - }; - - button@400 { - label = "Volume Down"; - linux,code = <KEY_VOLUMEDOWN>; - channel = <0>; - voltage = <400000>; - }; -}; - -&mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8h>; - vmmc-supply = <®_vcc3v0>; - bus-width = <4>; - cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */ - cd-inverted; - status = "okay"; -}; - -&pio { - mmc0_cd_pin_q8h: mmc0_cd_pin@0 { - allwinner,pins = "PB4"; - allwinner,function = "gpio_in"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; - }; -}; - -&r_uart { - pinctrl-names = "default"; - pinctrl-0 = <&r_uart_pins_a>; - status = "okay"; -}; - -&usb_otg { - dr_mode = "host"; - status = "okay"; -}; - -&usbphy { - status = "okay"; -}; +sun8i-a23-q8-tablet.dts
\ No newline at end of file diff --git a/arch/arm/boot/dts/sun8i-a23-q8-tablet.dts b/arch/arm/boot/dts/sun8i-a23-q8-tablet.dts new file mode 100644 index 000000000000..6062ea7a9903 --- /dev/null +++ b/arch/arm/boot/dts/sun8i-a23-q8-tablet.dts @@ -0,0 +1,65 @@ +/* + * Copyright 2015 Hans de Goede <hdegoede@redhat.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun8i-a23.dtsi" +#include "sun8i-q8-common.dtsi" + +/ { + model = "Q8 A23 Tablet"; + compatible = "allwinner,q8-a23", "allwinner,sun8i-a23"; +}; + +/* + * FIXME for now we only support host mode and rely on u-boot to have + * turned on Vbus which is controlled by the axp223 pmic on the board. + * + * Once we have axp223 support we should switch to fully supporting otg. + */ +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun8i-a23.dtsi b/arch/arm/boot/dts/sun8i-a23.dtsi index 2cc27c7a59dc..92e6616979ea 100644 --- a/arch/arm/boot/dts/sun8i-a23.dtsi +++ b/arch/arm/boot/dts/sun8i-a23.dtsi @@ -50,6 +50,31 @@ }; clocks { + ahb1_gates: clk@01c20060 { + #clock-cells = <1>; + compatible = "allwinner,sun8i-a23-ahb1-gates-clk"; + reg = <0x01c20060 0x8>; + clocks = <&ahb1>; + clock-indices = <1>, <6>, + <8>, <9>, <10>, + <13>, <14>, + <19>, <20>, + <21>, <24>, <26>, + <29>, <32>, <36>, + <40>, <44>, <46>, + <52>, <53>, + <54>, <57>; + clock-output-names = "ahb1_mipidsi", "ahb1_dma", + "ahb1_mmc0", "ahb1_mmc1", "ahb1_mmc2", + "ahb1_nand", "ahb1_sdram", + "ahb1_hstimer", "ahb1_spi0", + "ahb1_spi1", "ahb1_otg", "ahb1_ehci", + "ahb1_ohci", "ahb1_ve", "ahb1_lcd", + "ahb1_csi", "ahb1_be", "ahb1_fe", + "ahb1_gpu", "ahb1_msgbox", + "ahb1_spinlock", "ahb1_drc"; + }; + mbus_clk: clk@01c2015c { #clock-cells = <0>; compatible = "allwinner,sun8i-a23-mbus-clk"; diff --git a/arch/arm/boot/dts/sun8i-a33-et-q8-v1.6.dts b/arch/arm/boot/dts/sun8i-a33-et-q8-v1.6.dts index 19db844863bb..4519fd791a8f 100644..120000 --- a/arch/arm/boot/dts/sun8i-a33-et-q8-v1.6.dts +++ b/arch/arm/boot/dts/sun8i-a33-et-q8-v1.6.dts @@ -1,88 +1 @@ -/* - * Copyright 2015 Vishnu Patekar - * Vishnu Patekar <vishnupatekar0510@gmail.com> - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This file is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ - -/dts-v1/; -#include "sun8i-a33.dtsi" -#include "sunxi-common-regulators.dtsi" - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> -#include <dt-bindings/pinctrl/sun4i-a10.h> - -/ { - model = "ET Q8 Quad Core Tablet (v1.6)"; - compatible = "et,q8-v1.6", "allwinner,sun8i-a33"; - - aliases { - serial0 = &uart0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; -}; - -&lradc { - vref-supply = <®_vcc3v0>; - status = "okay"; - - button@200 { - label = "Volume Up"; - linux,code = <KEY_VOLUMEUP>; - channel = <0>; - voltage = <200000>; - }; - - button@400 { - label = "Volume Down"; - linux,code = <KEY_VOLUMEDOWN>; - channel = <0>; - voltage = <400000>; - }; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; - status = "okay"; -}; +sun8i-a33-q8-tablet.dts
\ No newline at end of file diff --git a/arch/arm/boot/dts/sun8i-a33-ippo-q8h-v1.2.dts b/arch/arm/boot/dts/sun8i-a33-ippo-q8h-v1.2.dts index a43897515fb6..4519fd791a8f 100644..120000 --- a/arch/arm/boot/dts/sun8i-a33-ippo-q8h-v1.2.dts +++ b/arch/arm/boot/dts/sun8i-a33-ippo-q8h-v1.2.dts @@ -1,133 +1 @@ -/* - * Copyright 2015 Hans de Goede <hdegoede@redhat.com> - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This file is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ - -/dts-v1/; -#include "sun8i-a33.dtsi" -#include "sunxi-common-regulators.dtsi" - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> -#include <dt-bindings/pinctrl/sun4i-a10.h> - -/ { - model = "Ippo Q8H Quad Core Tablet (v1.2)"; - compatible = "ippo,a33-q8h-v1.2", "allwinner,sun8i-a33"; - - aliases { - serial0 = &r_uart; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; -}; - -&i2c0 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins_a>; - status = "okay"; -}; - -&i2c1 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins_a>; - status = "okay"; -}; - -&lradc { - vref-supply = <®_vcc3v0>; - status = "okay"; - - button@200 { - label = "Volume Up"; - linux,code = <KEY_VOLUMEUP>; - channel = <0>; - voltage = <200000>; - }; - - button@400 { - label = "Volume Down"; - linux,code = <KEY_VOLUMEDOWN>; - channel = <0>; - voltage = <400000>; - }; -}; - -&mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8h>; - vmmc-supply = <®_vcc3v0>; - bus-width = <4>; - cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */ - cd-inverted; - status = "okay"; -}; - -&pio { - mmc0_cd_pin_q8h: mmc0_cd_pin@0 { - allwinner,pins = "PB4"; - allwinner,function = "gpio_in"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; - }; -}; - -&r_uart { - pinctrl-names = "default"; - pinctrl-0 = <&r_uart_pins_a>; - status = "okay"; -}; - -/* - * FIXME for now we only support host mode and rely on u-boot to have - * turned on Vbus which is controlled by the axp223 pmic on the board. - * - * Once we have axp223 support we should switch to fully supporting otg. - */ -&usb_otg { - dr_mode = "host"; - status = "okay"; -}; - -&usbphy { - status = "okay"; -}; +sun8i-a33-q8-tablet.dts
\ No newline at end of file diff --git a/arch/arm/boot/dts/sun8i-a33-q8-tablet.dts b/arch/arm/boot/dts/sun8i-a33-q8-tablet.dts new file mode 100644 index 000000000000..44b32296a025 --- /dev/null +++ b/arch/arm/boot/dts/sun8i-a33-q8-tablet.dts @@ -0,0 +1,65 @@ +/* + * Copyright 2015 Hans de Goede <hdegoede@redhat.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun8i-a33.dtsi" +#include "sun8i-q8-common.dtsi" + +/ { + model = "Q8 A33 Tablet"; + compatible = "allwinner,q8-a33", "allwinner,sun8i-a33"; +}; + +/* + * FIXME for now we only support host mode and rely on u-boot to have + * turned on Vbus which is controlled by the axp223 pmic on the board. + * + * Once we have axp223 support we should switch to fully supporting otg. + */ +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts b/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts index 1d5390d4e03a..13ce68f06dd6 100644 --- a/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts +++ b/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts @@ -130,6 +130,10 @@ }; }; +&r_rsb { + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_b>; diff --git a/arch/arm/boot/dts/sun8i-a33.dtsi b/arch/arm/boot/dts/sun8i-a33.dtsi index faa7d3c1fcea..001d8402ca18 100644 --- a/arch/arm/boot/dts/sun8i-a33.dtsi +++ b/arch/arm/boot/dts/sun8i-a33.dtsi @@ -72,6 +72,41 @@ clock-output-names = "pll11"; }; + ahb1_gates: clk@01c20060 { + #clock-cells = <1>; + compatible = "allwinner,sun8i-a33-ahb1-gates-clk"; + reg = <0x01c20060 0x8>; + clocks = <&ahb1>; + clock-indices = <1>, <5>, + <6>, <8>, <9>, + <10>, <13>, <14>, + <19>, <20>, + <21>, <24>, <26>, + <29>, <32>, <36>, + <40>, <44>, <46>, + <52>, <53>, + <54>, <57>, + <58>; + clock-output-names = "ahb1_mipidsi", "ahb1_ss", + "ahb1_dma","ahb1_mmc0", "ahb1_mmc1", + "ahb1_mmc2", "ahb1_nand", "ahb1_sdram", + "ahb1_hstimer", "ahb1_spi0", + "ahb1_spi1", "ahb1_otg", "ahb1_ehci", + "ahb1_ohci", "ahb1_ve", "ahb1_lcd", + "ahb1_csi", "ahb1_be", "ahb1_fe", + "ahb1_gpu", "ahb1_msgbox", + "ahb1_spinlock", "ahb1_drc", + "ahb1_sat"; + }; + + ss_clk: clk@01c2009c { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c2009c 0x4>; + clocks = <&osc24M>, <&pll6 0>; + clock-output-names = "ss"; + }; + mbus_clk: clk@01c2015c { #clock-cells = <0>; compatible = "allwinner,sun8i-a23-mbus-clk"; @@ -82,6 +117,16 @@ }; soc@01c00000 { + crypto: crypto-engine@01c15000 { + compatible = "allwinner,sun4i-a10-crypto"; + reg = <0x01c15000 0x1000>; + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ahb1_gates 5>, <&ss_clk>; + clock-names = "ahb", "mod"; + resets = <&ahb1_rst 5>; + reset-names = "ahb"; + }; + usb_otg: usb@01c19000 { compatible = "allwinner,sun8i-a33-musb"; reg = <0x01c19000 0x0400>; diff --git a/arch/arm/boot/dts/sun8i-q8-common.dtsi b/arch/arm/boot/dts/sun8i-q8-common.dtsi new file mode 100644 index 000000000000..1a69231d2da5 --- /dev/null +++ b/arch/arm/boot/dts/sun8i-q8-common.dtsi @@ -0,0 +1,101 @@ +/* + * Copyright 2015 Hans de Goede <hdegoede@redhat.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +#include "sunxi-q8-common.dtsi" + +#include <dt-bindings/pwm/pwm.h> + +/ { + aliases { + serial0 = &r_uart; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&bl_en_pin_q8>; + pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <8>; + enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ + /* backlight is powered by AXP223 DC1SW */ + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8>; + vmmc-supply = <®_vcc3v0>; + bus-width = <4>; + cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */ + cd-inverted; + status = "okay"; +}; + +&pio { + bl_en_pin_q8: bl_en_pin@0 { + allwinner,pins = "PH6"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + mmc0_cd_pin_q8: mmc0_cd_pin@0 { + allwinner,pins = "PB4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; +}; + +&r_rsb { + status = "okay"; +}; + +&r_uart { + pinctrl-names = "default"; + pinctrl-0 = <&r_uart_pins_a>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi index 5908e3dcf965..1118bf5cc4fb 100644 --- a/arch/arm/boot/dts/sun9i-a80.dtsi +++ b/arch/arm/boot/dts/sun9i-a80.dtsi @@ -594,7 +594,7 @@ clocks = <&apb0_gates 5>; gpio-controller; interrupt-controller; - #interrupt-cells = <2>; + #interrupt-cells = <3>; #size-cells = <0>; #gpio-cells = <3>; diff --git a/arch/arm/boot/dts/sunxi-q8-common.dtsi b/arch/arm/boot/dts/sunxi-q8-common.dtsi new file mode 100644 index 000000000000..b8241462fcea --- /dev/null +++ b/arch/arm/boot/dts/sunxi-q8-common.dtsi @@ -0,0 +1,83 @@ +/* + * Copyright 2015 Hans de Goede <hdegoede@redhat.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> +#include "sunxi-common-regulators.dtsi" + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; +}; + +&lradc { + vref-supply = <®_vcc3v0>; + status = "okay"; + + button@200 { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + channel = <0>; + voltage = <200000>; + }; + + button@400 { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + channel = <0>; + voltage = <400000>; + }; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/tegra124-nyan.dtsi b/arch/arm/boot/dts/tegra124-nyan.dtsi index a9aec23e06f2..40c23a0b7cfc 100644 --- a/arch/arm/boot/dts/tegra124-nyan.dtsi +++ b/arch/arm/boot/dts/tegra124-nyan.dtsi @@ -159,7 +159,7 @@ vin-ldo9-10-supply = <&vdd_5v0_sys>; vin-ldo11-supply = <&vdd_3v3_run>; - sd0 { + vdd_cpu: sd0 { regulator-name = "+VDD_CPU_AP"; regulator-min-microvolt = <700000>; regulator-max-microvolt = <1350000>; @@ -397,6 +397,13 @@ non-removable; }; + /* CPU DFLL clock */ + clock@0,70110000 { + status = "okay"; + vdd-cpu-supply = <&vdd_cpu>; + nvidia,i2c-fs-rate = <400000>; + }; + ahub@0,70300000 { i2s@0,70301100 { status = "okay"; @@ -487,6 +494,12 @@ }; }; + cpus { + cpu@0 { + vdd-cpu-supply = <&vdd_cpu>; + }; + }; + gpio-keys { compatible = "gpio-keys"; diff --git a/arch/arm/boot/dts/tegra124.dtsi b/arch/arm/boot/dts/tegra124.dtsi index 819e2ae2cabe..68669f791c8b 100644 --- a/arch/arm/boot/dts/tegra124.dtsi +++ b/arch/arm/boot/dts/tegra124.dtsi @@ -610,26 +610,20 @@ sata@0,70020000 { compatible = "nvidia,tegra124-ahci"; - reg = <0x0 0x70027000 0x0 0x2000>, /* AHCI */ - <0x0 0x70020000 0x0 0x7000>; /* SATA */ - + <0x0 0x70020000 0x0 0x7000>; /* SATA */ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&tegra_car TEGRA124_CLK_SATA>, - <&tegra_car TEGRA124_CLK_SATA_OOB>, - <&tegra_car TEGRA124_CLK_CML1>, - <&tegra_car TEGRA124_CLK_PLL_E>; + <&tegra_car TEGRA124_CLK_SATA_OOB>, + <&tegra_car TEGRA124_CLK_CML1>, + <&tegra_car TEGRA124_CLK_PLL_E>; clock-names = "sata", "sata-oob", "cml1", "pll_e"; - resets = <&tegra_car 124>, - <&tegra_car 123>, - <&tegra_car 129>; + <&tegra_car 123>, + <&tegra_car 129>; reset-names = "sata", "sata-oob", "sata-cold"; - phys = <&padctl TEGRA_XUSB_PADCTL_SATA>; phy-names = "sata-phy"; - status = "disabled"; }; @@ -638,7 +632,7 @@ reg = <0x0 0x70030000 0x0 0x10000>; interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA124_CLK_HDA>, - <&tegra_car TEGRA124_CLK_HDA2HDMI>, + <&tegra_car TEGRA124_CLK_HDA2HDMI>, <&tegra_car TEGRA124_CLK_HDA2CODEC_2X>; clock-names = "hda", "hda2hdmi", "hda2codec_2x"; resets = <&tegra_car 125>, /* hda */ diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/tegra20.dtsi index 969b828505ae..33173e1bace9 100644 --- a/arch/arm/boot/dts/tegra20.dtsi +++ b/arch/arm/boot/dts/tegra20.dtsi @@ -603,8 +603,8 @@ <&tegra_car TEGRA20_CLK_PLL_E>; clock-names = "pex", "afi", "pll_e"; resets = <&tegra_car 70>, - <&tegra_car 72>, - <&tegra_car 74>; + <&tegra_car 72>, + <&tegra_car 74>; reset-names = "pex", "afi", "pcie_x"; status = "disabled"; diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts index 6236bdecb48b..f2879cfcca62 100644 --- a/arch/arm/boot/dts/tegra30-apalis-eval.dts +++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts @@ -126,6 +126,10 @@ }; }; + hda@70030000 { + status = "okay"; + }; + sd1: sdhci@78000000 { status = "okay"; bus-width = <4>; @@ -149,6 +153,7 @@ usb-phy@7d000000 { status = "okay"; + dr_mode = "otg"; vbus-supply = <&usbo1_vbus_reg>; }; @@ -175,7 +180,7 @@ backlight: backlight { compatible = "pwm-backlight"; - /* PWM0 */ + /* PWM_BKL1 */ pwms = <&pwm 0 5000000>; brightness-levels = <255 231 223 207 191 159 127 0>; default-brightness-level = <6>; @@ -186,10 +191,10 @@ gpio-keys { compatible = "gpio-keys"; - power { - label = "Power"; + wakeup { + label = "WAKE1_MICO"; gpios = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_LOW>; - linux,code = <KEY_POWER>; + linux,code = <KEY_WAKEUP>; debounce-interval = <10>; gpio-key,wakeup; }; diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi index a5446cba9804..bf361277fe10 100644 --- a/arch/arm/boot/dts/tegra30-apalis.dtsi +++ b/arch/arm/boot/dts/tegra30-apalis.dtsi @@ -1,8 +1,9 @@ #include "tegra30.dtsi" /* - * Toradex Apalis T30 Device Tree - * Compatible for Revisions 1GB: V1.0A; 2GB: V1.0B, V1.0C + * Toradex Apalis T30 Module Device Tree + * Compatible for Revisions 1GB: V1.0A, V1.1A; 1GB IT: V1.1A; + * 2GB: V1.0B, V1.0C, V1.0E, V1.1A */ / { model = "Toradex Apalis T30"; @@ -33,8 +34,8 @@ host1x@50000000 { hdmi@54280000 { - vdd-supply = <&sys_3v3_reg>; - pll-supply = <&vio_reg>; + vdd-supply = <&avdd_hdmi_3v3_reg>; + pll-supply = <&avdd_hdmi_pll_1v8_reg>; nvidia,hpd-gpio = <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>; @@ -57,25 +58,25 @@ /* Apalis BKL1_PWM */ uart3_rts_n_pc0 { - nvidia,pins = "uart3_rts_n_pc0"; + nvidia,pins = "uart3_rts_n_pc0"; nvidia,function = "pwm0"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; }; /* BKL1_PWM_EN#, disable TPS65911 PMIC PWM backlight */ uart3_cts_n_pa1 { - nvidia,pins = "uart3_cts_n_pa1"; - nvidia,function = "rsvd1"; + nvidia,pins = "uart3_cts_n_pa1"; + nvidia,function = "rsvd2"; nvidia,pull = <TEGRA_PIN_PULL_UP>; nvidia,tristate = <TEGRA_PIN_DISABLE>; }; /* Apalis CAN1 on SPI6 */ spi2_cs0_n_px3 { - nvidia,pins = "spi2_cs0_n_px3", - "spi2_miso_px1", - "spi2_mosi_px0", - "spi2_sck_px2"; + nvidia,pins = "spi2_cs0_n_px3", + "spi2_miso_px1", + "spi2_mosi_px0", + "spi2_sck_px2"; nvidia,function = "spi6"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -91,10 +92,10 @@ /* Apalis CAN2 on SPI4 */ gmi_a16_pj7 { - nvidia,pins = "gmi_a16_pj7", - "gmi_a17_pb0", - "gmi_a18_pb1", - "gmi_a19_pk7"; + nvidia,pins = "gmi_a16_pj7", + "gmi_a17_pb0", + "gmi_a18_pb1", + "gmi_a19_pk7"; nvidia,function = "spi4"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -108,6 +109,30 @@ nvidia,enable-input = <TEGRA_PIN_ENABLE>; }; + /* Apalis Digital Audio */ + clk1_req_pee2 { + nvidia,pins = "clk1_req_pee2"; + nvidia,function = "hda"; + nvidia,pull = <TEGRA_PIN_PULL_NONE>; + nvidia,tristate = <TEGRA_PIN_DISABLE>; + }; + clk2_out_pw5 { + nvidia,pins = "clk2_out_pw5"; + nvidia,function = "extperiph2"; + nvidia,pull = <TEGRA_PIN_PULL_NONE>; + nvidia,tristate = <TEGRA_PIN_DISABLE>; + nvidia,enable-input = <TEGRA_PIN_DISABLE>; + }; + dap1_fs_pn0 { + nvidia,pins = "dap1_fs_pn0", + "dap1_din_pn1", + "dap1_dout_pn2", + "dap1_sclk_pn3"; + nvidia,function = "hda"; + nvidia,pull = <TEGRA_PIN_PULL_NONE>; + nvidia,tristate = <TEGRA_PIN_DISABLE>; + }; + /* Apalis I2C3 */ cam_i2c_scl_pbb1 { nvidia,pins = "cam_i2c_scl_pbb1", @@ -122,21 +147,21 @@ /* Apalis MMC1 */ sdmmc3_clk_pa6 { - nvidia,pins = "sdmmc3_clk_pa6", - "sdmmc3_cmd_pa7"; + nvidia,pins = "sdmmc3_clk_pa6", + "sdmmc3_cmd_pa7"; nvidia,function = "sdmmc3"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; }; sdmmc3_dat0_pb7 { - nvidia,pins = "sdmmc3_dat0_pb7", - "sdmmc3_dat1_pb6", - "sdmmc3_dat2_pb5", - "sdmmc3_dat3_pb4", - "sdmmc3_dat4_pd1", - "sdmmc3_dat5_pd0", - "sdmmc3_dat6_pd3", - "sdmmc3_dat7_pd4"; + nvidia,pins = "sdmmc3_dat0_pb7", + "sdmmc3_dat1_pb6", + "sdmmc3_dat2_pb5", + "sdmmc3_dat3_pb4", + "sdmmc3_dat4_pd1", + "sdmmc3_dat5_pd0", + "sdmmc3_dat6_pd3", + "sdmmc3_dat7_pd4"; nvidia,function = "sdmmc3"; nvidia,pull = <TEGRA_PIN_PULL_UP>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -151,32 +176,32 @@ }; /* Apalis PWM1 */ - gpio_pu6 { - nvidia,pins = "gpio_pu6"; + pu6 { + nvidia,pins = "pu6"; nvidia,function = "pwm3"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; }; /* Apalis PWM2 */ - gpio_pu5 { - nvidia,pins = "gpio_pu5"; + pu5 { + nvidia,pins = "pu5"; nvidia,function = "pwm2"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; }; /* Apalis PWM3 */ - gpio_pu4 { - nvidia,pins = "gpio_pu4"; + pu4 { + nvidia,pins = "pu4"; nvidia,function = "pwm1"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; }; /* Apalis PWM4 */ - gpio_pu3 { - nvidia,pins = "gpio_pu3"; + pu3 { + nvidia,pins = "pu3"; nvidia,function = "pwm0"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -198,11 +223,11 @@ nvidia,tristate = <TEGRA_PIN_DISABLE>; }; sdmmc1_cmd_pz1 { - nvidia,pins = "sdmmc1_cmd_pz1", - "sdmmc1_dat0_py7", - "sdmmc1_dat1_py6", - "sdmmc1_dat2_py5", - "sdmmc1_dat3_py4"; + nvidia,pins = "sdmmc1_cmd_pz1", + "sdmmc1_dat0_py7", + "sdmmc1_dat1_py6", + "sdmmc1_dat2_py5", + "sdmmc1_dat3_py4"; nvidia,function = "sdmmc1"; nvidia,pull = <TEGRA_PIN_PULL_UP>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -218,10 +243,10 @@ /* Apalis SPI1 */ spi1_sck_px5 { - nvidia,pins = "spi1_sck_px5", - "spi1_mosi_px4", - "spi1_miso_px7", - "spi1_cs0_n_px6"; + nvidia,pins = "spi1_sck_px5", + "spi1_mosi_px4", + "spi1_miso_px7", + "spi1_cs0_n_px6"; nvidia,function = "spi1"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -229,10 +254,10 @@ /* Apalis SPI2 */ lcd_sck_pz4 { - nvidia,pins = "lcd_sck_pz4", - "lcd_sdout_pn5", - "lcd_sdin_pz2", - "lcd_cs0_n_pn4"; + nvidia,pins = "lcd_sck_pz4", + "lcd_sdout_pn5", + "lcd_sdin_pz2", + "lcd_cs0_n_pn4"; nvidia,function = "spi5"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -240,14 +265,14 @@ /* Apalis UART1 */ ulpi_data0 { - nvidia,pins = "ulpi_data0_po1", - "ulpi_data1_po2", - "ulpi_data2_po3", - "ulpi_data3_po4", - "ulpi_data4_po5", - "ulpi_data5_po6", - "ulpi_data6_po7", - "ulpi_data7_po0"; + nvidia,pins = "ulpi_data0_po1", + "ulpi_data1_po2", + "ulpi_data2_po3", + "ulpi_data3_po4", + "ulpi_data4_po5", + "ulpi_data5_po6", + "ulpi_data6_po7", + "ulpi_data7_po0"; nvidia,function = "uarta"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -255,10 +280,10 @@ /* Apalis UART2 */ ulpi_clk_py0 { - nvidia,pins = "ulpi_clk_py0", - "ulpi_dir_py1", - "ulpi_nxt_py2", - "ulpi_stp_py3"; + nvidia,pins = "ulpi_clk_py0", + "ulpi_dir_py1", + "ulpi_nxt_py2", + "ulpi_stp_py3"; nvidia,function = "uartd"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -266,8 +291,8 @@ /* Apalis UART3 */ uart2_rxd_pc3 { - nvidia,pins = "uart2_rxd_pc3", - "uart2_txd_pc2"; + nvidia,pins = "uart2_rxd_pc3", + "uart2_txd_pc2"; nvidia,function = "uartb"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -275,8 +300,8 @@ /* Apalis UART4 */ uart3_rxd_pw7 { - nvidia,pins = "uart3_rxd_pw7", - "uart3_txd_pw6"; + nvidia,pins = "uart3_rxd_pw7", + "uart3_txd_pw6"; nvidia,function = "uartc"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -312,21 +337,21 @@ /* eMMC (On-module) */ sdmmc4_clk_pcc4 { - nvidia,pins = "sdmmc4_clk_pcc4", - "sdmmc4_rst_n_pcc3"; + nvidia,pins = "sdmmc4_clk_pcc4", + "sdmmc4_rst_n_pcc3"; nvidia,function = "sdmmc4"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; }; sdmmc4_dat0_paa0 { - nvidia,pins = "sdmmc4_dat0_paa0", - "sdmmc4_dat1_paa1", - "sdmmc4_dat2_paa2", - "sdmmc4_dat3_paa3", - "sdmmc4_dat4_paa4", - "sdmmc4_dat5_paa5", - "sdmmc4_dat6_paa6", - "sdmmc4_dat7_paa7"; + nvidia,pins = "sdmmc4_dat0_paa0", + "sdmmc4_dat1_paa1", + "sdmmc4_dat2_paa2", + "sdmmc4_dat3_paa3", + "sdmmc4_dat4_paa4", + "sdmmc4_dat5_paa5", + "sdmmc4_dat6_paa6", + "sdmmc4_dat7_paa7"; nvidia,function = "sdmmc4"; nvidia,pull = <TEGRA_PIN_PULL_UP>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -334,10 +359,10 @@ /* LVDS Transceiver Configuration */ pbb0 { - nvidia,pins = "pbb0", - "pbb7", - "pcc1", - "pcc2"; + nvidia,pins = "pbb0", + "pbb7", + "pcc1", + "pcc2"; nvidia,function = "rsvd2"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -345,10 +370,10 @@ nvidia,lock = <TEGRA_PIN_DISABLE>; }; pbb3 { - nvidia,pins = "pbb3", - "pbb4", - "pbb5", - "pbb6"; + nvidia,pins = "pbb3", + "pbb4", + "pbb5", + "pbb6"; nvidia,function = "displayb"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -635,6 +660,7 @@ nvidia,sys-clock-req-active-high; }; + /* eMMC */ sdhci@78000600 { status = "okay"; bus-width = <8>; @@ -666,18 +692,40 @@ #address-cells = <1>; #size-cells = <0>; - sys_3v3_reg: regulator@100 { + avdd_hdmi_pll_1v8_reg: regulator@100 { compatible = "regulator-fixed"; reg = <100>; + regulator-name = "+V1.8_AVDD_HDMI_PLL"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + enable-active-high; + gpio = <&pmic 6 GPIO_ACTIVE_HIGH>; + vin-supply = <&vio_reg>; + }; + + sys_3v3_reg: regulator@101 { + compatible = "regulator-fixed"; + reg = <101>; regulator-name = "3v3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-always-on; }; - charge_pump_5v0_reg: regulator@101 { + avdd_hdmi_3v3_reg: regulator@102 { compatible = "regulator-fixed"; - reg = <101>; + reg = <102>; + regulator-name = "+V3.3_AVDD_HDMI"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + gpio = <&pmic 6 GPIO_ACTIVE_HIGH>; + vin-supply = <&sys_3v3_reg>; + }; + + charge_pump_5v0_reg: regulator@103 { + compatible = "regulator-fixed"; + reg = <103>; regulator-name = "5v0"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; diff --git a/arch/arm/boot/dts/tegra30-colibri-eval-v3.dts b/arch/arm/boot/dts/tegra30-colibri-eval-v3.dts index 4d3ddc585641..3ff019f47d00 100644 --- a/arch/arm/boot/dts/tegra30-colibri-eval-v3.dts +++ b/arch/arm/boot/dts/tegra30-colibri-eval-v3.dts @@ -55,7 +55,7 @@ /* M41T0M6 real time clock on carrier board */ rtc@68 { - compatible = "stm,m41t00"; + compatible = "st,m41t00"; reg = <0x68>; }; }; @@ -84,6 +84,7 @@ }; }; + /* SD/MMC */ sdhci@78000200 { status = "okay"; bus-width = <4>; @@ -136,10 +137,10 @@ gpio-keys { compatible = "gpio-keys"; - power { - label = "Power"; + wakeup { + label = "SODIMM pin 45 wakeup"; gpios = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_HIGH>; - linux,code = <KEY_POWER>; + linux,code = <KEY_WAKEUP>; debounce-interval = <10>; gpio-key,wakeup; }; diff --git a/arch/arm/boot/dts/tegra30-colibri.dtsi b/arch/arm/boot/dts/tegra30-colibri.dtsi index c4ed1bec4d92..2d8c58fd9357 100644 --- a/arch/arm/boot/dts/tegra30-colibri.dtsi +++ b/arch/arm/boot/dts/tegra30-colibri.dtsi @@ -2,8 +2,8 @@ #include "tegra30.dtsi" /* - * Toradex Colibri T30 Device Tree - * Compatible for Revisions 1.1B/1.1C/1.1D + * Toradex Colibri T30 Module Device Tree + * Compatible for Revisions V1.1B, V1.1C, V1.1D, V1.1E; IT: V1.1A */ / { model = "Toradex Colibri T30"; @@ -15,8 +15,8 @@ host1x@50000000 { hdmi@54280000 { - vdd-supply = <&sys_3v3_reg>; - pll-supply = <&vio_reg>; + vdd-supply = <&avdd_hdmi_3v3_reg>; + pll-supply = <&avdd_hdmi_pll_1v8_reg>; nvidia,hpd-gpio = <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>; @@ -39,7 +39,7 @@ /* Colibri Backlight PWM<A> */ sdmmc3_dat3_pb4 { - nvidia,pins = "sdmmc3_dat3_pb4"; + nvidia,pins = "sdmmc3_dat3_pb4"; nvidia,function = "pwm0"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -66,15 +66,6 @@ nvidia,enable-input = <TEGRA_PIN_ENABLE>; }; - /* Thermal alert, need to be disabled */ - lcd_dc1_pd2 { - nvidia,pins = "lcd_dc1_pd2"; - nvidia,function = "rsvd3"; - nvidia,pull = <TEGRA_PIN_PULL_NONE>; - nvidia,tristate = <TEGRA_PIN_DISABLE>; - nvidia,enable-input = <TEGRA_PIN_ENABLE>; - }; - /* Colibri MMC */ kb_row10_ps2 { nvidia,pins = "kb_row10_ps2"; @@ -83,11 +74,11 @@ nvidia,tristate = <TEGRA_PIN_DISABLE>; }; kb_row11_ps3 { - nvidia,pins = "kb_row11_ps3", - "kb_row12_ps4", - "kb_row13_ps5", - "kb_row14_ps6", - "kb_row15_ps7"; + nvidia,pins = "kb_row11_ps3", + "kb_row12_ps4", + "kb_row13_ps5", + "kb_row14_ps6", + "kb_row15_ps7"; nvidia,function = "sdmmc2"; nvidia,pull = <TEGRA_PIN_PULL_UP>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -95,17 +86,17 @@ /* Colibri SSP */ ulpi_clk_py0 { - nvidia,pins = "ulpi_clk_py0", - "ulpi_dir_py1", - "ulpi_nxt_py2", - "ulpi_stp_py3"; + nvidia,pins = "ulpi_clk_py0", + "ulpi_dir_py1", + "ulpi_nxt_py2", + "ulpi_stp_py3"; nvidia,function = "spi1"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; }; sdmmc3_dat6_pd3 { - nvidia,pins = "sdmmc3_dat6_pd3", - "sdmmc3_dat7_pd4"; + nvidia,pins = "sdmmc3_dat6_pd3", + "sdmmc3_dat7_pd4"; nvidia,function = "spdif"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_ENABLE>; @@ -113,14 +104,14 @@ /* Colibri UART_A */ ulpi_data0 { - nvidia,pins = "ulpi_data0_po1", - "ulpi_data1_po2", - "ulpi_data2_po3", - "ulpi_data3_po4", - "ulpi_data4_po5", - "ulpi_data5_po6", - "ulpi_data6_po7", - "ulpi_data7_po0"; + nvidia,pins = "ulpi_data0_po1", + "ulpi_data1_po2", + "ulpi_data2_po3", + "ulpi_data3_po4", + "ulpi_data4_po5", + "ulpi_data5_po6", + "ulpi_data6_po7", + "ulpi_data7_po0"; nvidia,function = "uarta"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -128,10 +119,10 @@ /* Colibri UART_B */ gmi_a16_pj7 { - nvidia,pins = "gmi_a16_pj7", - "gmi_a17_pb0", - "gmi_a18_pb1", - "gmi_a19_pk7"; + nvidia,pins = "gmi_a16_pj7", + "gmi_a17_pb0", + "gmi_a18_pb1", + "gmi_a19_pk7"; nvidia,function = "uartd"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -139,8 +130,8 @@ /* Colibri UART_C */ uart2_rxd { - nvidia,pins = "uart2_rxd_pc3", - "uart2_txd_pc2"; + nvidia,pins = "uart2_rxd_pc3", + "uart2_txd_pc2"; nvidia,function = "uartb"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; @@ -148,25 +139,59 @@ /* eMMC */ sdmmc4_clk_pcc4 { - nvidia,pins = "sdmmc4_clk_pcc4", - "sdmmc4_rst_n_pcc3"; + nvidia,pins = "sdmmc4_clk_pcc4", + "sdmmc4_rst_n_pcc3"; nvidia,function = "sdmmc4"; nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; }; sdmmc4_dat0_paa0 { - nvidia,pins = "sdmmc4_dat0_paa0", - "sdmmc4_dat1_paa1", - "sdmmc4_dat2_paa2", - "sdmmc4_dat3_paa3", - "sdmmc4_dat4_paa4", - "sdmmc4_dat5_paa5", - "sdmmc4_dat6_paa6", - "sdmmc4_dat7_paa7"; + nvidia,pins = "sdmmc4_dat0_paa0", + "sdmmc4_dat1_paa1", + "sdmmc4_dat2_paa2", + "sdmmc4_dat3_paa3", + "sdmmc4_dat4_paa4", + "sdmmc4_dat5_paa5", + "sdmmc4_dat6_paa6", + "sdmmc4_dat7_paa7"; nvidia,function = "sdmmc4"; nvidia,pull = <TEGRA_PIN_PULL_UP>; nvidia,tristate = <TEGRA_PIN_DISABLE>; }; + + /* Power I2C (On-module) */ + pwr_i2c_scl_pz6 { + nvidia,pins = "pwr_i2c_scl_pz6", + "pwr_i2c_sda_pz7"; + nvidia,function = "i2cpwr"; + nvidia,pull = <TEGRA_PIN_PULL_NONE>; + nvidia,tristate = <TEGRA_PIN_DISABLE>; + nvidia,enable-input = <TEGRA_PIN_ENABLE>; + nvidia,lock = <TEGRA_PIN_DISABLE>; + nvidia,open-drain = <TEGRA_PIN_ENABLE>; + }; + + /* + * THERMD_ALERT#, unlatched I2C address pin of LM95245 + * temperature sensor therefore requires disabling for + * now + */ + lcd_dc1_pd2 { + nvidia,pins = "lcd_dc1_pd2"; + nvidia,function = "rsvd3"; + nvidia,pull = <TEGRA_PIN_PULL_NONE>; + nvidia,tristate = <TEGRA_PIN_DISABLE>; + nvidia,enable-input = <TEGRA_PIN_ENABLE>; + }; + + /* TOUCH_PEN_INT# */ + pv0 { + nvidia,pins = "pv0"; + nvidia,function = "rsvd1"; + nvidia,pull = <TEGRA_PIN_PULL_NONE>; + nvidia,tristate = <TEGRA_PIN_DISABLE>; + nvidia,enable-input = <TEGRA_PIN_ENABLE>; + }; }; }; @@ -236,7 +261,7 @@ /* * EN_+V3.3 switching via FET: * +V3.3_AUDIO_AVDD_S, +V3.3 and +V1.8_VDD_LAN - * see also v3_3 fixed supply + * see also 3v3 fixed supply */ ldo2_reg: ldo2 { regulator-name = "en_3v3"; @@ -295,6 +320,46 @@ }; }; + /* STMPE811 touch screen controller */ + stmpe811@41 { + compatible = "st,stmpe811"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x41>; + interrupts = <TEGRA_GPIO(V, 0) IRQ_TYPE_LEVEL_LOW>; + interrupt-parent = <&gpio>; + interrupt-controller; + id = <0>; + blocks = <0x5>; + irq-trigger = <0x1>; + + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + reg = <0>; + /* 3.25 MHz ADC clock speed */ + st,adc-freq = <1>; + /* 8 sample average control */ + st,ave-ctrl = <3>; + /* 7 length fractional part in z */ + st,fraction-z = <7>; + /* + * 50 mA typical 80 mA max touchscreen drivers + * current limit value + */ + st,i-drive = <1>; + /* 12-bit ADC */ + st,mod-12b = <1>; + /* internal ADC reference */ + st,ref-sel = <0>; + /* ADC converstion time: 80 clocks */ + st,sample-time = <4>; + /* 1 ms panel driver settling time */ + st,settling = <3>; + /* 5 ms touch detect interrupt delay */ + st,touch-det-delay = <5>; + }; + }; + /* * LM95245 temperature sensor * Note: OVERT_N directly connected to PMIC PWRDN @@ -331,7 +396,8 @@ nvidia,sys-clock-req-active-high; }; - emmc: sdhci@78000600 { + /* eMMC */ + sdhci@78000600 { status = "okay"; bus-width = <8>; non-removable; @@ -365,18 +431,40 @@ #address-cells = <1>; #size-cells = <0>; - sys_3v3_reg: regulator@100 { + avdd_hdmi_pll_1v8_reg: regulator@100 { compatible = "regulator-fixed"; reg = <100>; + regulator-name = "+V1.8_AVDD_HDMI_PLL"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + enable-active-high; + gpio = <&pmic 6 GPIO_ACTIVE_HIGH>; + vin-supply = <&vio_reg>; + }; + + sys_3v3_reg: regulator@101 { + compatible = "regulator-fixed"; + reg = <101>; regulator-name = "3v3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-always-on; }; - charge_pump_5v0_reg: regulator@101 { + avdd_hdmi_3v3_reg: regulator@102 { compatible = "regulator-fixed"; - reg = <101>; + reg = <102>; + regulator-name = "+V3.3_AVDD_HDMI"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + gpio = <&pmic 6 GPIO_ACTIVE_HIGH>; + vin-supply = <&sys_3v3_reg>; + }; + + charge_pump_5v0_reg: regulator@103 { + compatible = "regulator-fixed"; + reg = <103>; regulator-name = "5v0"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi index c6938ad1b543..313e260529a3 100644 --- a/arch/arm/boot/dts/tegra30.dtsi +++ b/arch/arm/boot/dts/tegra30.dtsi @@ -42,8 +42,8 @@ <&tegra_car TEGRA30_CLK_CML0>; clock-names = "pex", "afi", "pll_e", "cml"; resets = <&tegra_car 70>, - <&tegra_car 72>, - <&tegra_car 74>; + <&tegra_car 72>, + <&tegra_car 74>; reset-names = "pex", "afi", "pcie_x"; status = "disabled"; @@ -153,7 +153,7 @@ &tegra_car TEGRA30_CLK_GR3D2>; clock-names = "3d", "3d2"; resets = <&tegra_car 24>, - <&tegra_car 98>; + <&tegra_car 98>; reset-names = "3d", "3d2"; }; @@ -457,7 +457,7 @@ }; i2c@7000c000 { - compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c"; + compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c"; reg = <0x7000c000 0x100>; interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; @@ -662,7 +662,7 @@ reg = <0x70030000 0x10000>; interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA30_CLK_HDA>, - <&tegra_car TEGRA30_CLK_HDA2HDMI>, + <&tegra_car TEGRA30_CLK_HDA2HDMI>, <&tegra_car TEGRA30_CLK_HDA2CODEC_2X>; clock-names = "hda", "hda2hdmi", "hda2codec_2x"; resets = <&tegra_car 125>, /* hda */ diff --git a/arch/arm/boot/dts/uniphier-ph1-ld4-ref.dts b/arch/arm/boot/dts/uniphier-ph1-ld4-ref.dts index bfd3bb8c8285..f1e9d40149ab 100644 --- a/arch/arm/boot/dts/uniphier-ph1-ld4-ref.dts +++ b/arch/arm/boot/dts/uniphier-ph1-ld4-ref.dts @@ -57,8 +57,7 @@ }; chosen { - bootargs = "console=ttyS0,115200"; - stdout-path = &serial0; + stdout-path = "serial0:115200n8"; }; aliases { @@ -74,12 +73,11 @@ }; &extbus { - ranges = <0 0x00000000 0x0f000000 0x01000000 - 1 0x00000000 0x00000000 0x08000000>; + ranges = <1 0x00000000 0x42000000 0x02000000>; }; &support_card { - ranges = <0x00000000 1 0x03f00000 0x00100000>; + ranges = <0x00000000 1 0x01f00000 0x00100000>; }; ðsc { diff --git a/arch/arm/boot/dts/uniphier-ph1-ld4.dtsi b/arch/arm/boot/dts/uniphier-ph1-ld4.dtsi index a6a185fae8f1..af493819548d 100644 --- a/arch/arm/boot/dts/uniphier-ph1-ld4.dtsi +++ b/arch/arm/boot/dts/uniphier-ph1-ld4.dtsi @@ -55,6 +55,7 @@ device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <0>; + next-level-cache = <&l2>; }; }; @@ -91,6 +92,18 @@ #size-cells = <1>; }; + l2: l2-cache@500c0000 { + compatible = "socionext,uniphier-system-cache"; + reg = <0x500c0000 0x2000>, <0x503c0100 0x4>, + <0x506c0000 0x400>; + interrupts = <0 174 4>, <0 175 4>; + cache-unified; + cache-size = <(512 * 1024)>; + cache-sets = <256>; + cache-line-size = <128>; + cache-level = <2>; + }; + serial0: serial@54006800 { compatible = "socionext,uniphier-uart"; status = "disabled"; @@ -187,10 +200,9 @@ clock-frequency = <100000>; }; - system-bus-controller-misc@59800000 { - compatible = "socionext,uniphier-system-bus-controller-misc", - "syscon"; - reg = <0x59800000 0x2000>; + system-bus-controller@58c00000 { + compatible = "socionext,uniphier-system-bus-controller"; + reg = <0x58c00000 0x400>, <0x59800000 0x2000>; }; usb0: usb@5a800100 { diff --git a/arch/arm/boot/dts/uniphier-ph1-ld6b-ref.dts b/arch/arm/boot/dts/uniphier-ph1-ld6b-ref.dts index f80f772d99fb..5baa9fc9c888 100644 --- a/arch/arm/boot/dts/uniphier-ph1-ld6b-ref.dts +++ b/arch/arm/boot/dts/uniphier-ph1-ld6b-ref.dts @@ -57,8 +57,7 @@ }; chosen { - bootargs = "console=ttyS0,115200"; - stdout-path = &serial0; + stdout-path = "serial0:115200n8"; }; aliases { @@ -76,12 +75,11 @@ }; &extbus { - ranges = <0 0x00000000 0x0f000000 0x01000000 - 1 0x00000000 0x00000000 0x08000000>; + ranges = <1 0x00000000 0x42000000 0x02000000>; }; &support_card { - ranges = <0x00000000 1 0x03f00000 0x00100000>; + ranges = <0x00000000 1 0x01f00000 0x00100000>; }; ðsc { diff --git a/arch/arm/boot/dts/uniphier-ph1-pro4-ref.dts b/arch/arm/boot/dts/uniphier-ph1-pro4-ref.dts index 69a5b7d39629..24626687d4df 100644 --- a/arch/arm/boot/dts/uniphier-ph1-pro4-ref.dts +++ b/arch/arm/boot/dts/uniphier-ph1-pro4-ref.dts @@ -57,8 +57,7 @@ }; chosen { - bootargs = "console=ttyS0,115200"; - stdout-path = &serial0; + stdout-path = "serial0:115200n8"; }; aliases { @@ -76,12 +75,11 @@ }; &extbus { - ranges = <0 0x00000000 0x0f000000 0x01000000 - 1 0x00000000 0x00000000 0x08000000>; + ranges = <1 0x00000000 0x42000000 0x02000000>; }; &support_card { - ranges = <0x00000000 1 0x03f00000 0x00100000>; + ranges = <0x00000000 1 0x01f00000 0x00100000>; }; ðsc { diff --git a/arch/arm/boot/dts/uniphier-ph1-pro4.dtsi b/arch/arm/boot/dts/uniphier-ph1-pro4.dtsi index e8bbc454d788..254642fe0e71 100644 --- a/arch/arm/boot/dts/uniphier-ph1-pro4.dtsi +++ b/arch/arm/boot/dts/uniphier-ph1-pro4.dtsi @@ -56,12 +56,14 @@ device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <0>; + next-level-cache = <&l2>; }; cpu@1 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <1>; + next-level-cache = <&l2>; }; }; @@ -98,6 +100,18 @@ #size-cells = <1>; }; + l2: l2-cache@500c0000 { + compatible = "socionext,uniphier-system-cache"; + reg = <0x500c0000 0x2000>, <0x503c0100 0x4>, + <0x506c0000 0x400>; + interrupts = <0 174 4>, <0 175 4>; + cache-unified; + cache-size = <(768 * 1024)>; + cache-sets = <256>; + cache-line-size = <128>; + cache-level = <2>; + }; + serial0: serial@54006800 { compatible = "socionext,uniphier-uart"; status = "disabled"; @@ -218,10 +232,9 @@ clock-frequency = <400000>; }; - system-bus-controller-misc@59800000 { - compatible = "socionext,uniphier-system-bus-controller-misc", - "syscon"; - reg = <0x59800000 0x2000>; + system-bus-controller@58c00000 { + compatible = "socionext,uniphier-system-bus-controller"; + reg = <0x58c00000 0x400>, <0x59800000 0x2000>; }; usb2: usb@5a800100 { diff --git a/arch/arm/boot/dts/uniphier-ph1-pro5.dtsi b/arch/arm/boot/dts/uniphier-ph1-pro5.dtsi index 59c2b127cffa..11eb76239feb 100644 --- a/arch/arm/boot/dts/uniphier-ph1-pro5.dtsi +++ b/arch/arm/boot/dts/uniphier-ph1-pro5.dtsi @@ -56,12 +56,14 @@ device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <0>; + next-level-cache = <&l2>; }; cpu@1 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <1>; + next-level-cache = <&l2>; }; }; @@ -98,6 +100,31 @@ #size-cells = <1>; }; + l2: l2-cache@500c0000 { + compatible = "socionext,uniphier-system-cache"; + reg = <0x500c0000 0x2000>, <0x503c0100 0x8>, + <0x506c0000 0x400>; + interrupts = <0 190 4>, <0 191 4>; + cache-unified; + cache-size = <(2 * 1024 * 1024)>; + cache-sets = <512>; + cache-line-size = <128>; + cache-level = <2>; + next-level-cache = <&l3>; + }; + + l3: l3-cache@500c8000 { + compatible = "socionext,uniphier-system-cache"; + reg = <0x500c8000 0x2000>, <0x503c8100 0x8>, + <0x506c8000 0x400>; + interrupts = <0 174 4>, <0 175 4>; + cache-unified; + cache-size = <(2 * 1024 * 1024)>; + cache-sets = <512>; + cache-line-size = <256>; + cache-level = <3>; + }; + serial0: serial@54006800 { compatible = "socionext,uniphier-uart"; status = "disabled"; @@ -214,10 +241,9 @@ clock-frequency = <400000>; }; - system-bus-controller-misc@59800000 { - compatible = "socionext,uniphier-system-bus-controller-misc", - "syscon"; - reg = <0x59800000 0x2000>; + system-bus-controller@58c00000 { + compatible = "socionext,uniphier-system-bus-controller"; + reg = <0x58c00000 0x400>, <0x59800000 0x2000>; }; pinctrl: pinctrl@5f801000 { diff --git a/arch/arm/boot/dts/uniphier-ph1-sld3-ref.dts b/arch/arm/boot/dts/uniphier-ph1-sld3-ref.dts index 1a440f87fa92..b7a032156789 100644 --- a/arch/arm/boot/dts/uniphier-ph1-sld3-ref.dts +++ b/arch/arm/boot/dts/uniphier-ph1-sld3-ref.dts @@ -58,8 +58,7 @@ }; chosen { - bootargs = "console=ttyS0,115200"; - stdout-path = &serial0; + stdout-path = "serial0:115200n8"; }; aliases { @@ -75,12 +74,11 @@ }; &extbus { - ranges = <0 0x00000000 0x0f000000 0x01000000 - 1 0x00000000 0x00000000 0x08000000>; + ranges = <1 0x00000000 0x42000000 0x02000000>; }; &support_card { - ranges = <0x00000000 1 0x03f00000 0x00100000>; + ranges = <0x00000000 1 0x01f00000 0x00100000>; }; ðsc { diff --git a/arch/arm/boot/dts/uniphier-ph1-sld3.dtsi b/arch/arm/boot/dts/uniphier-ph1-sld3.dtsi index 3cc90cd37a26..691a17d765c2 100644 --- a/arch/arm/boot/dts/uniphier-ph1-sld3.dtsi +++ b/arch/arm/boot/dts/uniphier-ph1-sld3.dtsi @@ -56,12 +56,14 @@ device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <0>; + next-level-cache = <&l2>; }; cpu@1 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <1>; + next-level-cache = <&l2>; }; }; @@ -120,6 +122,18 @@ <0x20000100 0x100>; }; + l2: l2-cache@500c0000 { + compatible = "socionext,uniphier-system-cache"; + reg = <0x500c0000 0x2000>, <0x503c0100 0x4>, + <0x506c0000 0x400>; + interrupts = <0 174 4>, <0 175 4>; + cache-unified; + cache-size = <(512 * 1024)>; + cache-sets = <256>; + cache-line-size = <128>; + cache-level = <2>; + }; + serial0: serial@54006800 { compatible = "socionext,uniphier-uart"; status = "disabled"; @@ -202,10 +216,9 @@ clock-frequency = <400000>; }; - system-bus-controller-misc@59800000 { - compatible = "socionext,uniphier-system-bus-controller-misc", - "syscon"; - reg = <0x59800000 0x2000>; + system-bus-controller@58c00000 { + compatible = "socionext,uniphier-system-bus-controller"; + reg = <0x58c00000 0x400>, <0x59800000 0x2000>; }; usb0: usb@5a800100 { diff --git a/arch/arm/boot/dts/uniphier-ph1-sld8-ref.dts b/arch/arm/boot/dts/uniphier-ph1-sld8-ref.dts index 955d417a5c42..fc7250c61674 100644 --- a/arch/arm/boot/dts/uniphier-ph1-sld8-ref.dts +++ b/arch/arm/boot/dts/uniphier-ph1-sld8-ref.dts @@ -57,8 +57,7 @@ }; chosen { - bootargs = "console=ttyS0,115200"; - stdout-path = &serial0; + stdout-path = "serial0:115200n8"; }; aliases { @@ -74,12 +73,11 @@ }; &extbus { - ranges = <0 0x00000000 0x0f000000 0x01000000 - 1 0x00000000 0x00000000 0x08000000>; + ranges = <1 0x00000000 0x42000000 0x02000000>; }; &support_card { - ranges = <0x00000000 1 0x03f00000 0x00100000>; + ranges = <0x00000000 1 0x01f00000 0x00100000>; }; ðsc { diff --git a/arch/arm/boot/dts/uniphier-ph1-sld8.dtsi b/arch/arm/boot/dts/uniphier-ph1-sld8.dtsi index 58067dfc16e5..e88559b66be7 100644 --- a/arch/arm/boot/dts/uniphier-ph1-sld8.dtsi +++ b/arch/arm/boot/dts/uniphier-ph1-sld8.dtsi @@ -55,6 +55,7 @@ device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <0>; + next-level-cache = <&l2>; }; }; @@ -91,6 +92,18 @@ #size-cells = <1>; }; + l2: l2-cache@500c0000 { + compatible = "socionext,uniphier-system-cache"; + reg = <0x500c0000 0x2000>, <0x503c0100 0x4>, + <0x506c0000 0x400>; + interrupts = <0 174 4>, <0 175 4>; + cache-unified; + cache-size = <(256 * 1024)>; + cache-sets = <256>; + cache-line-size = <128>; + cache-level = <2>; + }; + serial0: serial@54006800 { compatible = "socionext,uniphier-uart"; status = "disabled"; @@ -187,10 +200,9 @@ clock-frequency = <100000>; }; - system-bus-controller-misc@59800000 { - compatible = "socionext,uniphier-system-bus-controller-misc", - "syscon"; - reg = <0x59800000 0x2000>; + system-bus-controller@58c00000 { + compatible = "socionext,uniphier-system-bus-controller"; + reg = <0x58c00000 0x400>, <0x59800000 0x2000>; }; usb0: usb@5a800100 { diff --git a/arch/arm/boot/dts/uniphier-proxstream2-gentil.dts b/arch/arm/boot/dts/uniphier-proxstream2-gentil.dts new file mode 100644 index 000000000000..9d7ec5c204dd --- /dev/null +++ b/arch/arm/boot/dts/uniphier-proxstream2-gentil.dts @@ -0,0 +1,78 @@ +/* + * Device Tree Source for UniPhier ProXstream2 Gentil Board + * + * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +/include/ "uniphier-proxstream2.dtsi" + +/ { + model = "UniPhier ProXstream2 Gentil Board"; + compatible = "socionext,proxstream2-gentil", "socionext,proxstream2"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x80000000>; + }; + + chosen { + stdout-path = "serial2:115200n8"; + }; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + serial2 = &serial2; + i2c0 = &i2c0; + i2c4 = &i2c4; + i2c5 = &i2c5; + i2c6 = &i2c6; + }; +}; + +&serial2 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/uniphier-proxstream2-vodka.dts b/arch/arm/boot/dts/uniphier-proxstream2-vodka.dts new file mode 100644 index 000000000000..498acac3d95d --- /dev/null +++ b/arch/arm/boot/dts/uniphier-proxstream2-vodka.dts @@ -0,0 +1,78 @@ +/* + * Device Tree Source for UniPhier ProXstream2 Vodka Board + * + * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +/include/ "uniphier-proxstream2.dtsi" + +/ { + model = "UniPhier ProXstream2 Vodka Board"; + compatible = "socionext,proxstream2-vodka", "socionext,proxstream2"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x80000000>; + }; + + chosen { + stdout-path = "serial2:115200n8"; + }; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + serial2 = &serial2; + i2c0 = &i2c0; + i2c4 = &i2c4; + i2c5 = &i2c5; + i2c6 = &i2c6; + }; +}; + +&serial2 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/uniphier-proxstream2.dtsi b/arch/arm/boot/dts/uniphier-proxstream2.dtsi index 4c7b24611012..259f1a909e24 100644 --- a/arch/arm/boot/dts/uniphier-proxstream2.dtsi +++ b/arch/arm/boot/dts/uniphier-proxstream2.dtsi @@ -56,24 +56,28 @@ device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <0>; + next-level-cache = <&l2>; }; cpu@1 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <1>; + next-level-cache = <&l2>; }; cpu@2 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <2>; + next-level-cache = <&l2>; }; cpu@3 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <3>; + next-level-cache = <&l2>; }; }; @@ -110,6 +114,18 @@ #size-cells = <1>; }; + l2: l2-cache@500c0000 { + compatible = "socionext,uniphier-system-cache"; + reg = <0x500c0000 0x2000>, <0x503c0100 0x4>, + <0x506c0000 0x400>; + interrupts = <0 174 4>, <0 175 4>, <0 190 4>, <0 191 4>; + cache-unified; + cache-size = <(1280 * 1024)>; + cache-sets = <512>; + cache-line-size = <128>; + cache-level = <2>; + }; + serial0: serial@54006800 { compatible = "socionext,uniphier-uart"; status = "disabled"; @@ -235,10 +251,9 @@ clock-frequency = <400000>; }; - system-bus-controller-misc@59800000 { - compatible = "socionext,uniphier-system-bus-controller-misc", - "syscon"; - reg = <0x59800000 0x2000>; + system-bus-controller@58c00000 { + compatible = "socionext,uniphier-system-bus-controller"; + reg = <0x58c00000 0x400>, <0x59800000 0x2000>; }; pinctrl: pinctrl@5f801000 { diff --git a/arch/arm/boot/dts/vf-colibri.dtsi b/arch/arm/boot/dts/vf-colibri.dtsi index 68ca125b56ea..e5949b934945 100644 --- a/arch/arm/boot/dts/vf-colibri.dtsi +++ b/arch/arm/boot/dts/vf-colibri.dtsi @@ -52,6 +52,26 @@ pinctrl-0 = <&pinctrl_i2c0>; }; +&nfc { + assigned-clocks = <&clks VF610_CLK_NFC>; + assigned-clock-rates = <33000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_nfc>; + status = "okay"; + + nand@0 { + compatible = "fsl,vf610-nfc-nandcs"; + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-ecc-strength = <32>; + nand-ecc-step-size = <2048>; + nand-on-flash-bbt; + }; +}; + &pwm0 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pwm0>; @@ -156,6 +176,25 @@ >; }; + pinctrl_nfc: nfcgrp { + fsl,pins = < + VF610_PAD_PTD23__NF_IO7 0x28df + VF610_PAD_PTD22__NF_IO6 0x28df + VF610_PAD_PTD21__NF_IO5 0x28df + VF610_PAD_PTD20__NF_IO4 0x28df + VF610_PAD_PTD19__NF_IO3 0x28df + VF610_PAD_PTD18__NF_IO2 0x28df + VF610_PAD_PTD17__NF_IO1 0x28df + VF610_PAD_PTD16__NF_IO0 0x28df + VF610_PAD_PTB24__NF_WE_B 0x28c2 + VF610_PAD_PTB25__NF_CE0_B 0x28c2 + VF610_PAD_PTB27__NF_RE_B 0x28c2 + VF610_PAD_PTC26__NF_RB_B 0x283d + VF610_PAD_PTC27__NF_ALE 0x28c2 + VF610_PAD_PTC28__NF_CLE 0x28c2 + >; + }; + pinctrl_pwm0: pwm0grp { fsl,pins = < VF610_PAD_PTB0__FTM0_CH0 0x1182 diff --git a/arch/arm/boot/dts/vf500-colibri-eval-v3.dts b/arch/arm/boot/dts/vf500-colibri-eval-v3.dts index 7fc782c4fc52..c3173fc9e833 100644 --- a/arch/arm/boot/dts/vf500-colibri-eval-v3.dts +++ b/arch/arm/boot/dts/vf500-colibri-eval-v3.dts @@ -15,3 +15,8 @@ model = "Toradex Colibri VF50 on Colibri Evaluation Board"; compatible = "toradex,vf500-colibri_vf50-on-eval", "toradex,vf500-colibri_vf50", "fsl,vf500"; }; + +&touchscreen { + vf50-ts-min-pressure = <200>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/vf500-colibri.dtsi b/arch/arm/boot/dts/vf500-colibri.dtsi index cee34a32f25b..84f091d1fcf2 100644 --- a/arch/arm/boot/dts/vf500-colibri.dtsi +++ b/arch/arm/boot/dts/vf500-colibri.dtsi @@ -17,4 +17,51 @@ memory { reg = <0x80000000 0x8000000>; }; + + touchscreen: vf50-touchscreen { + compatible = "toradex,vf50-touchscreen"; + io-channels = <&adc1 0>,<&adc0 0>, + <&adc0 1>,<&adc1 2>; + xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>; + yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + interrupt-parent = <&gpio0>; + interrupts = <8 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "idle","default","gpios"; + pinctrl-0 = <&pinctrl_touchctrl_idle>; + pinctrl-1 = <&pinctrl_touchctrl_default>; + pinctrl-2 = <&pinctrl_touchctrl_gpios>; + vf50-ts-min-pressure = <200>; + status = "disabled"; + }; +}; + +&iomuxc { + vf610-colibri { + pinctrl_touchctrl_idle: touchctrl_idle { + fsl,pins = < + VF610_PAD_PTA18__GPIO_8 0x006d + VF610_PAD_PTA19__GPIO_9 0x006c + >; + }; + + pinctrl_touchctrl_default: touchctrl_default { + fsl,pins = < + VF610_PAD_PTA18__ADC0_SE0 0x0040 + VF610_PAD_PTA19__ADC0_SE1 0x0040 + VF610_PAD_PTA16__ADC1_SE0 0x0040 + VF610_PAD_PTB2__ADC1_SE2 0x0040 + >; + }; + + pinctrl_touchctrl_gpios: touchctrl_gpios { + fsl,pins = < + VF610_PAD_PTA23__GPIO_13 0x22e9 + VF610_PAD_PTB23__GPIO_93 0x22e9 + VF610_PAD_PTA22__GPIO_12 0x22e9 + VF610_PAD_PTA11__GPIO_4 0x22e9 + >; + }; + }; }; diff --git a/arch/arm/boot/dts/vf610-twr.dts b/arch/arm/boot/dts/vf610-twr.dts index 375ab23ca743..5438ee4be2ec 100644 --- a/arch/arm/boot/dts/vf610-twr.dts +++ b/arch/arm/boot/dts/vf610-twr.dts @@ -237,6 +237,33 @@ >; }; + pinctrl_nfc: nfcgrp { + fsl,pins = < + VF610_PAD_PTD31__NF_IO15 0x28df + VF610_PAD_PTD30__NF_IO14 0x28df + VF610_PAD_PTD29__NF_IO13 0x28df + VF610_PAD_PTD28__NF_IO12 0x28df + VF610_PAD_PTD27__NF_IO11 0x28df + VF610_PAD_PTD26__NF_IO10 0x28df + VF610_PAD_PTD25__NF_IO9 0x28df + VF610_PAD_PTD24__NF_IO8 0x28df + VF610_PAD_PTD23__NF_IO7 0x28df + VF610_PAD_PTD22__NF_IO6 0x28df + VF610_PAD_PTD21__NF_IO5 0x28df + VF610_PAD_PTD20__NF_IO4 0x28df + VF610_PAD_PTD19__NF_IO3 0x28df + VF610_PAD_PTD18__NF_IO2 0x28df + VF610_PAD_PTD17__NF_IO1 0x28df + VF610_PAD_PTD16__NF_IO0 0x28df + VF610_PAD_PTB24__NF_WE_B 0x28c2 + VF610_PAD_PTB25__NF_CE0_B 0x28c2 + VF610_PAD_PTB27__NF_RE_B 0x28c2 + VF610_PAD_PTC26__NF_RB_B 0x283d + VF610_PAD_PTC27__NF_ALE 0x28c2 + VF610_PAD_PTC28__NF_CLE 0x28c2 + >; + }; + pinctrl_pwm0: pwm0grp { fsl,pins = < VF610_PAD_PTB0__FTM0_CH0 0x1582 @@ -274,6 +301,26 @@ }; }; +&nfc { + assigned-clocks = <&clks VF610_CLK_NFC>; + assigned-clock-rates = <33000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_nfc>; + status = "okay"; + + nand@0 { + compatible = "fsl,vf610-nfc-nandcs"; + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + nand-bus-width = <16>; + nand-ecc-mode = "hw"; + nand-ecc-strength = <24>; + nand-ecc-step-size = <2048>; + nand-on-flash-bbt; + }; +}; + &pwm0 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pwm0>; diff --git a/arch/arm/boot/dts/vfxxx.dtsi b/arch/arm/boot/dts/vfxxx.dtsi index 6865137fd114..6736bae43a5b 100644 --- a/arch/arm/boot/dts/vfxxx.dtsi +++ b/arch/arm/boot/dts/vfxxx.dtsi @@ -564,6 +564,17 @@ status = "disabled"; }; + nfc: nand@400e0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,vf610-nfc"; + reg = <0x400e0000 0x4000>; + interrupts = <83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks VF610_CLK_NFC>; + clock-names = "nfc"; + status = "disabled"; + }; + i2c2: i2c@400e6000 { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/wm8750.dtsi b/arch/arm/boot/dts/wm8750.dtsi index 557a9c2ace49..46d076d7302b 100644 --- a/arch/arm/boot/dts/wm8750.dtsi +++ b/arch/arm/boot/dts/wm8750.dtsi @@ -17,7 +17,7 @@ cpu { device_type = "cpu"; - compatible = "arm,arm1176ej-s"; + compatible = "arm,arm1176jzf"; }; }; diff --git a/arch/arm/mach-keystone/keystone.c b/arch/arm/mach-keystone/keystone.c index e288010522f9..c279293f084c 100644 --- a/arch/arm/mach-keystone/keystone.c +++ b/arch/arm/mach-keystone/keystone.c @@ -97,6 +97,9 @@ static long long __init keystone_pv_fixup(void) } static const char *const keystone_match[] __initconst = { + "ti,k2hk", + "ti,k2e", + "ti,k2l", "ti,keystone", NULL, }; diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms index c6e2c75c04fc..4043c35962cc 100644 --- a/arch/arm64/Kconfig.platforms +++ b/arch/arm64/Kconfig.platforms @@ -29,10 +29,10 @@ config ARCH_EXYNOS7 help This enables support for Samsung Exynos7 SoC family -config ARCH_FSL_LS2085A - bool "Freescale LS2085A SOC" +config ARCH_LAYERSCAPE + bool "ARMv8 based Freescale Layerscape SoC family" help - This enables support for Freescale LS2085A SOC. + This enables support for the Freescale Layerscape SoC family. config ARCH_HISI bool "Hisilicon SoC Family" @@ -67,6 +67,11 @@ config ARCH_SEATTLE help This enables support for AMD Seattle SOC Family +config ARCH_STRATIX10 + bool "Altera's Stratix 10 SoCFPGA Family" + help + This enables support for Altera's Stratix 10 SoCFPGA Family. + config ARCH_TEGRA bool "NVIDIA Tegra SoC Family" select ARCH_HAS_RESET_CONTROLLER diff --git a/arch/arm64/boot/dts/Makefile b/arch/arm64/boot/dts/Makefile index b01ec43d1ca9..eb3c42d97175 100644 --- a/arch/arm64/boot/dts/Makefile +++ b/arch/arm64/boot/dts/Makefile @@ -1,3 +1,4 @@ +dts-dirs += altera dts-dirs += amd dts-dirs += apm dts-dirs += arm diff --git a/arch/arm64/boot/dts/altera/Makefile b/arch/arm64/boot/dts/altera/Makefile new file mode 100644 index 000000000000..d7a641698d77 --- /dev/null +++ b/arch/arm64/boot/dts/altera/Makefile @@ -0,0 +1,5 @@ +dtb-$(CONFIG_ARCH_STRATIX10) += socfpga_stratix10_socdk.dtb + +always := $(dtb-y) +subdir-y := $(dts-dirs) +clean-files := *.dtb diff --git a/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi b/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi new file mode 100644 index 000000000000..445aa678f914 --- /dev/null +++ b/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi @@ -0,0 +1,358 @@ +/* + * Copyright Altera Corporation (C) 2015. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +/dts-v1/; + +/ { + compatible = "altr,socfpga-stratix10"; + #address-cells = <2>; + #size-cells = <2>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + compatible = "arm,cortex-a53", "arm,armv8"; + device_type = "cpu"; + enable-method = "psci"; + reg = <0x0>; + }; + + cpu1: cpu@1 { + compatible = "arm,cortex-a53", "arm,armv8"; + device_type = "cpu"; + enable-method = "psci"; + reg = <0x1>; + }; + + cpu2: cpu@2 { + compatible = "arm,cortex-a53", "arm,armv8"; + device_type = "cpu"; + enable-method = "psci"; + reg = <0x2>; + }; + + cpu3: cpu@3 { + compatible = "arm,cortex-a53", "arm,armv8"; + device_type = "cpu"; + enable-method = "psci"; + reg = <0x3>; + }; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <0 120 8>, + <0 121 8>, + <0 122 8>, + <0 123 8>; + interrupt-affinity = <&cpu0>, + <&cpu1>, + <&cpu2>, + <&cpu3>; + }; + + psci { + compatible = "arm,psci-0.2"; + method = "smc"; + }; + + intc: intc@fffc1000 { + compatible = "arm,gic-400", "arm,cortex-a15-gic"; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0x0 0xfffc1000 0x1000>, + <0x0 0xfffc2000 0x2000>, + <0x0 0xfffc4000 0x2000>, + <0x0 0xfffc6000 0x2000>; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + device_type = "soc"; + interrupt-parent = <&intc>; + ranges = <0 0 0 0xffffffff>; + + clkmgr@ffd1000 { + compatible = "altr,clk-mgr"; + reg = <0xffd10000 0x1000>; + }; + + gmac0: ethernet@ff800000 { + compatible = "altr,socfpga-stmmac", "snps,dwmac-3.74a", "snps,dwmac"; + reg = <0xff800000 0x2000>; + interrupts = <0 90 4>; + interrupt-names = "macirq"; + mac-address = [00 00 00 00 00 00]; + status = "disabled"; + }; + + gmac1: ethernet@ff802000 { + compatible = "altr,socfpga-stmmac", "snps,dwmac-3.74a", "snps,dwmac"; + reg = <0xff802000 0x2000>; + interrupts = <0 91 4>; + interrupt-names = "macirq"; + mac-address = [00 00 00 00 00 00]; + status = "disabled"; + }; + + gmac2: ethernet@ff804000 { + compatible = "altr,socfpga-stmmac", "snps,dwmac-3.74a", "snps,dwmac"; + reg = <0xff804000 0x2000>; + interrupts = <0 92 4>; + interrupt-names = "macirq"; + mac-address = [00 00 00 00 00 00]; + status = "disabled"; + }; + + gpio0: gpio@ffc03200 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dw-apb-gpio"; + reg = <0xffc03200 0x100>; + status = "disabled"; + + porta: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <24>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 110 4>; + }; + }; + + gpio1: gpio@ffc03300 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dw-apb-gpio"; + reg = <0xffc03300 0x100>; + status = "disabled"; + + portb: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <24>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 110 4>; + }; + }; + + i2c0: i2c@ffc02800 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc02800 0x100>; + interrupts = <0 103 4>; + status = "disabled"; + }; + + i2c1: i2c@ffc02900 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc02900 0x100>; + interrupts = <0 104 4>; + status = "disabled"; + }; + + i2c2: i2c@ffc02a00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc02a00 0x100>; + interrupts = <0 105 4>; + status = "disabled"; + }; + + i2c3: i2c@ffc02b00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc02b00 0x100>; + interrupts = <0 106 4>; + status = "disabled"; + }; + + i2c4: i2c@ffc02c00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc02c00 0x100>; + interrupts = <0 107 4>; + status = "disabled"; + }; + + mmc: dwmmc0@ff808000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "altr,socfpga-dw-mshc"; + reg = <0xff808000 0x1000>; + interrupts = <0 96 4>; + fifo-depth = <0x400>; + status = "disabled"; + }; + + ocram: sram@ffe00000 { + compatible = "mmio-sram"; + reg = <0xffe00000 0x100000>; + }; + + rst: rstmgr@ffd11000 { + #reset-cells = <1>; + compatible = "altr,rst-mgr"; + reg = <0xffd11000 0x1000>; + }; + + spi0: spi@ffda4000 { + compatible = "snps,dw-apb-ssi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xffda4000 0x1000>; + interrupts = <0 101 4>; + num-chipselect = <4>; + bus-num = <0>; + status = "disabled"; + }; + + spi1: spi@ffda5000 { + compatible = "snps,dw-apb-ssi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xffda5000 0x1000>; + interrupts = <0 102 4>; + num-chipselect = <4>; + bus-num = <0>; + status = "disabled"; + }; + + sysmgr: sysmgr@ffd12000 { + compatible = "altr,sys-mgr", "syscon"; + reg = <0xffd12000 0x1000>; + }; + + /* Local timer */ + timer { + compatible = "arm,armv8-timer"; + interrupts = <1 13 0xf01>, + <1 14 0xf01>, + <1 11 0xf01>, + <1 10 0xf01>; + }; + + timer0: timer0@ffc03000 { + compatible = "snps,dw-apb-timer"; + interrupts = <0 113 4>; + reg = <0xffc03000 0x100>; + }; + + timer1: timer1@ffc03100 { + compatible = "snps,dw-apb-timer"; + interrupts = <0 114 4>; + reg = <0xffc03100 0x100>; + }; + + timer2: timer2@ffd00000 { + compatible = "snps,dw-apb-timer"; + interrupts = <0 115 4>; + reg = <0xffd00000 0x100>; + }; + + timer3: timer3@ffd00100 { + compatible = "snps,dw-apb-timer"; + interrupts = <0 116 4>; + reg = <0xffd00100 0x100>; + }; + + uart0: serial0@ffc02000 { + compatible = "snps,dw-apb-uart"; + reg = <0xffc02000 0x100>; + interrupts = <0 108 4>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart1: serial1@ffc02100 { + compatible = "snps,dw-apb-uart"; + reg = <0xffc02100 0x100>; + interrupts = <0 109 4>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + usbphy0: usbphy@0 { + #phy-cells = <0>; + compatible = "usb-nop-xceiv"; + status = "okay"; + }; + + usb0: usb@ffb00000 { + compatible = "snps,dwc2"; + reg = <0xffb00000 0x40000>; + interrupts = <0 93 4>; + phys = <&usbphy0>; + phy-names = "usb2-phy"; + status = "disabled"; + }; + + usb1: usb@ffb40000 { + compatible = "snps,dwc2"; + reg = <0xffb40000 0x40000>; + interrupts = <0 94 4>; + phys = <&usbphy0>; + phy-names = "usb2-phy"; + status = "disabled"; + }; + + watchdog0: watchdog@ffd00200 { + compatible = "snps,dw-wdt"; + reg = <0xffd00200 0x100>; + interrupts = <0 117 4>; + status = "disabled"; + }; + + watchdog1: watchdog@ffd00300 { + compatible = "snps,dw-wdt"; + reg = <0xffd00300 0x100>; + interrupts = <0 118 4>; + status = "disabled"; + }; + + watchdog2: watchdog@ffd00400 { + compatible = "snps,dw-wdt"; + reg = <0xffd00400 0x100>; + interrupts = <0 125 4>; + status = "disabled"; + }; + + watchdog3: watchdog@ffd00500 { + compatible = "snps,dw-wdt"; + reg = <0xffd00500 0x100>; + interrupts = <0 126 4>; + status = "disabled"; + }; + }; +}; diff --git a/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dts b/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dts new file mode 100644 index 000000000000..41ea2dba2fce --- /dev/null +++ b/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dts @@ -0,0 +1,39 @@ +/* + * Copyright Altera Corporation (C) 2015. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +/include/ "socfpga_stratix10.dtsi" + +/ { + model = "SoCFPGA Stratix 10 SoCDK"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + device_type = "memory"; + /* We expect the bootloader to fill in the reg */ + reg = <0 0 0 0>; + }; +}; + +&uart0 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/apm/Makefile b/arch/arm64/boot/dts/apm/Makefile index a2afabbc1717..c75f17a49471 100644 --- a/arch/arm64/boot/dts/apm/Makefile +++ b/arch/arm64/boot/dts/apm/Makefile @@ -1,4 +1,5 @@ dtb-$(CONFIG_ARCH_XGENE) += apm-mustang.dtb +dtb-$(CONFIG_ARCH_XGENE) += apm-merlin.dtb always := $(dtb-y) subdir-y := $(dts-dirs) diff --git a/arch/arm64/boot/dts/apm/apm-merlin.dts b/arch/arm64/boot/dts/apm/apm-merlin.dts new file mode 100644 index 000000000000..119a469bd189 --- /dev/null +++ b/arch/arm64/boot/dts/apm/apm-merlin.dts @@ -0,0 +1,72 @@ +/* + * dts file for AppliedMicro (APM) Merlin Board + * + * Copyright (C) 2015, Applied Micro Circuits Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +/dts-v1/; + +/include/ "apm-shadowcat.dtsi" + +/ { + model = "APM X-Gene Merlin board"; + compatible = "apm,merlin", "apm,xgene-shadowcat"; + + chosen { }; + + memory { + device_type = "memory"; + reg = < 0x1 0x00000000 0x0 0x80000000 >; + }; + + gpio-keys { + compatible = "gpio-keys"; + button@1 { + label = "POWER"; + linux,code = <116>; + linux,input-type = <0x1>; + interrupts = <0x0 0x28 0x1>; + }; + }; + + poweroff_mbox: poweroff_mbox@10548000 { + compatible = "syscon"; + reg = <0x0 0x10548000 0x0 0x30>; + }; + + poweroff: poweroff@10548010 { + compatible = "syscon-poweroff"; + regmap = <&poweroff_mbox>; + offset = <0x10>; + mask = <0x1>; + }; +}; + +&serial0 { + status = "ok"; +}; + +&sata1 { + status = "ok"; +}; + +&sata2 { + status = "ok"; +}; + +&sata3 { + status = "ok"; +}; + +&sgenet0 { + status = "ok"; +}; + +&xgenet1 { + status = "ok"; +}; diff --git a/arch/arm64/boot/dts/apm/apm-mustang.dts b/arch/arm64/boot/dts/apm/apm-mustang.dts index 4c55833d8a41..01cdeda93c3a 100644 --- a/arch/arm64/boot/dts/apm/apm-mustang.dts +++ b/arch/arm64/boot/dts/apm/apm-mustang.dts @@ -33,6 +33,18 @@ interrupts = <0x0 0x2d 0x1>; }; }; + + poweroff_mbox: poweroff_mbox@10548000 { + compatible = "syscon"; + reg = <0x0 0x10548000 0x0 0x30>; + }; + + poweroff: poweroff@10548010 { + compatible = "syscon-poweroff"; + regmap = <&poweroff_mbox>; + offset = <0x10>; + mask = <0x1>; + }; }; &pcie0clk { diff --git a/arch/arm64/boot/dts/apm/apm-shadowcat.dtsi b/arch/arm64/boot/dts/apm/apm-shadowcat.dtsi new file mode 100644 index 000000000000..c804f8f1f38c --- /dev/null +++ b/arch/arm64/boot/dts/apm/apm-shadowcat.dtsi @@ -0,0 +1,271 @@ +/* + * dts file for AppliedMicro (APM) X-Gene Shadowcat SOC + * + * Copyright (C) 2015, Applied Micro Circuits Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +/ { + compatible = "apm,xgene-shadowcat"; + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + cpu@000 { + device_type = "cpu"; + compatible = "apm,strega", "arm,armv8"; + reg = <0x0 0x000>; + enable-method = "spin-table"; + cpu-release-addr = <0x1 0x0000fff8>; + }; + cpu@001 { + device_type = "cpu"; + compatible = "apm,strega", "arm,armv8"; + reg = <0x0 0x001>; + enable-method = "spin-table"; + cpu-release-addr = <0x1 0x0000fff8>; + }; + cpu@100 { + device_type = "cpu"; + compatible = "apm,strega", "arm,armv8"; + reg = <0x0 0x100>; + enable-method = "spin-table"; + cpu-release-addr = <0x1 0x0000fff8>; + }; + cpu@101 { + device_type = "cpu"; + compatible = "apm,strega", "arm,armv8"; + reg = <0x0 0x101>; + enable-method = "spin-table"; + cpu-release-addr = <0x1 0x0000fff8>; + }; + cpu@200 { + device_type = "cpu"; + compatible = "apm,strega", "arm,armv8"; + reg = <0x0 0x200>; + enable-method = "spin-table"; + cpu-release-addr = <0x1 0x0000fff8>; + }; + cpu@201 { + device_type = "cpu"; + compatible = "apm,strega", "arm,armv8"; + reg = <0x0 0x201>; + enable-method = "spin-table"; + cpu-release-addr = <0x1 0x0000fff8>; + }; + cpu@300 { + device_type = "cpu"; + compatible = "apm,strega", "arm,armv8"; + reg = <0x0 0x300>; + enable-method = "spin-table"; + cpu-release-addr = <0x1 0x0000fff8>; + }; + cpu@301 { + device_type = "cpu"; + compatible = "apm,strega", "arm,armv8"; + reg = <0x0 0x301>; + enable-method = "spin-table"; + cpu-release-addr = <0x1 0x0000fff8>; + }; + }; + + gic: interrupt-controller@78090000 { + compatible = "arm,cortex-a15-gic"; + #interrupt-cells = <3>; + #address-cells = <2>; + #size-cells = <2>; + interrupt-controller; + interrupts = <1 9 0xf04>; /* GIC Maintenence IRQ */ + ranges = <0 0 0 0x79000000 0x0 0x800000>; /* MSI Range */ + reg = <0x0 0x78090000 0x0 0x10000>, /* GIC Dist */ + <0x0 0x780A0000 0x0 0x20000>, /* GIC CPU */ + <0x0 0x780C0000 0x0 0x10000>, /* GIC VCPU Control */ + <0x0 0x780E0000 0x0 0x20000>; /* GIC VCPU */ + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <1 12 0xff04>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <1 0 0xff04>, /* Secure Phys IRQ */ + <1 13 0xff04>, /* Non-secure Phys IRQ */ + <1 14 0xff04>, /* Virt IRQ */ + <1 15 0xff04>; /* Hyp IRQ */ + clock-frequency = <50000000>; + }; + + soc { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + refclk: refclk { + compatible = "fixed-clock"; + #clock-cells = <1>; + clock-frequency = <100000000>; + clock-output-names = "refclk"; + }; + + socpll: socpll@17000120 { + compatible = "apm,xgene-socpll-clock"; + #clock-cells = <1>; + clocks = <&refclk 0>; + reg = <0x0 0x17000120 0x0 0x1000>; + clock-output-names = "socpll"; + }; + + socplldiv2: socplldiv2 { + compatible = "fixed-factor-clock"; + #clock-cells = <1>; + clocks = <&socpll 0>; + clock-mult = <1>; + clock-div = <2>; + clock-output-names = "socplldiv2"; + }; + + pcie0clk: pcie0clk@1f2bc000 { + compatible = "apm,xgene-device-clock"; + #clock-cells = <1>; + clocks = <&socplldiv2 0>; + reg = <0x0 0x1f2bc000 0x0 0x1000>; + reg-names = "csr-reg"; + clock-output-names = "pcie0clk"; + }; + + xge0clk: xge0clk@1f61c000 { + compatible = "apm,xgene-device-clock"; + #clock-cells = <1>; + clocks = <&socplldiv2 0>; + reg = <0x0 0x1f61c000 0x0 0x1000>; + reg-names = "csr-reg"; + enable-mask = <0x3>; + csr-mask = <0x3>; + clock-output-names = "xge0clk"; + }; + + xge1clk: xge1clk@1f62c000 { + compatible = "apm,xgene-device-clock"; + #clock-cells = <1>; + clocks = <&socplldiv2 0>; + reg = <0x0 0x1f62c000 0x0 0x1000>; + reg-names = "csr-reg"; + enable-mask = <0x3>; + csr-mask = <0x3>; + clock-output-names = "xge1clk"; + }; + }; + + scu: system-clk-controller@17000000 { + compatible = "apm,xgene-scu","syscon"; + reg = <0x0 0x17000000 0x0 0x400>; + }; + + reboot: reboot@17000014 { + compatible = "syscon-reboot"; + regmap = <&scu>; + offset = <0x14>; + mask = <0x1>; + }; + + serial0: serial@10600000 { + device_type = "serial"; + compatible = "ns16550"; + reg = <0 0x10600000 0x0 0x1000>; + reg-shift = <2>; + clock-frequency = <10000000>; + interrupt-parent = <&gic>; + interrupts = <0x0 0x4c 0x4>; + }; + + sata1: sata@1a000000 { + compatible = "apm,xgene-ahci"; + reg = <0x0 0x1a000000 0x0 0x1000>, + <0x0 0x1f200000 0x0 0x1000>, + <0x0 0x1f20d000 0x0 0x1000>, + <0x0 0x1f20e000 0x0 0x1000>; + interrupts = <0x0 0x5a 0x4>; + dma-coherent; + }; + + sata2: sata@1a200000 { + compatible = "apm,xgene-ahci"; + reg = <0x0 0x1a200000 0x0 0x1000>, + <0x0 0x1f210000 0x0 0x1000>, + <0x0 0x1f21d000 0x0 0x1000>, + <0x0 0x1f21e000 0x0 0x1000>; + interrupts = <0x0 0x5b 0x4>; + dma-coherent; + }; + + sata3: sata@1a400000 { + compatible = "apm,xgene-ahci"; + reg = <0x0 0x1a400000 0x0 0x1000>, + <0x0 0x1f220000 0x0 0x1000>, + <0x0 0x1f22d000 0x0 0x1000>, + <0x0 0x1f22e000 0x0 0x1000>; + interrupts = <0x0 0x5c 0x4>; + dma-coherent; + }; + + sbgpio: sbgpio@17001000{ + compatible = "apm,xgene-gpio-sb"; + reg = <0x0 0x17001000 0x0 0x400>; + #gpio-cells = <2>; + gpio-controller; + interrupts = <0x0 0x28 0x1>, + <0x0 0x29 0x1>, + <0x0 0x2a 0x1>, + <0x0 0x2b 0x1>, + <0x0 0x2c 0x1>, + <0x0 0x2d 0x1>, + <0x0 0x2e 0x1>, + <0x0 0x2f 0x1>; + }; + + sgenet0: ethernet@1f610000 { + compatible = "apm,xgene2-sgenet"; + status = "disabled"; + reg = <0x0 0x1f610000 0x0 0x10000>, + <0x0 0x1f600000 0x0 0Xd100>, + <0x0 0x20000000 0x0 0X20000>; + interrupts = <0 96 4>, + <0 97 4>; + dma-coherent; + clocks = <&xge0clk 0>; + local-mac-address = [00 01 73 00 00 01]; + phy-connection-type = "sgmii"; + }; + + xgenet1: ethernet@1f620000 { + compatible = "apm,xgene2-xgenet"; + status = "disabled"; + reg = <0x0 0x1f620000 0x0 0x10000>, + <0x0 0x1f600000 0x0 0Xd100>, + <0x0 0x20000000 0x0 0X220000>; + interrupts = <0 108 4>, + <0 109 4>; + port-id = <1>; + dma-coherent; + clocks = <&xge1clk 0>; + local-mac-address = [00 01 73 00 00 02]; + phy-connection-type = "xgmii"; + }; + }; +}; diff --git a/arch/arm64/boot/dts/apm/apm-storm.dtsi b/arch/arm64/boot/dts/apm/apm-storm.dtsi index d6c9630a5c20..6c5ed119934f 100644 --- a/arch/arm64/boot/dts/apm/apm-storm.dtsi +++ b/arch/arm64/boot/dts/apm/apm-storm.dtsi @@ -97,6 +97,11 @@ clock-frequency = <50000000>; }; + pmu { + compatible = "apm,potenza-pmu", "arm,armv8-pmuv3"; + interrupts = <1 12 0xff04>; + }; + soc { compatible = "simple-bus"; #address-cells = <2>; @@ -407,6 +412,18 @@ 0x0 0x1f 0x4>; }; + scu: system-clk-controller@17000000 { + compatible = "apm,xgene-scu","syscon"; + reg = <0x0 0x17000000 0x0 0x400>; + }; + + reboot: reboot@17000014 { + compatible = "syscon-reboot"; + regmap = <&scu>; + offset = <0x14>; + mask = <0x1>; + }; + csw: csw@7e200000 { compatible = "apm,xgene-csw", "syscon"; reg = <0x0 0x7e200000 0x0 0x1000>; diff --git a/arch/arm64/boot/dts/arm/juno-base.dtsi b/arch/arm64/boot/dts/arm/juno-base.dtsi index e3ee96036eca..dd5158eb5872 100644 --- a/arch/arm64/boot/dts/arm/juno-base.dtsi +++ b/arch/arm64/boot/dts/arm/juno-base.dtsi @@ -17,6 +17,18 @@ }; }; + mailbox: mhu@2b1f0000 { + compatible = "arm,mhu", "arm,primecell"; + reg = <0x0 0x2b1f0000 0x0 0x1000>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "mhu_lpri_rx", + "mhu_hpri_rx"; + #mbox-cells = <1>; + clocks = <&soc_refclk100mhz>; + clock-names = "apb_pclk"; + }; + gic: interrupt-controller@2c010000 { compatible = "arm,gic-400", "arm,cortex-a15-gic"; reg = <0x0 0x2c010000 0 0x1000>, @@ -44,6 +56,53 @@ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>; }; + sram: sram@2e000000 { + compatible = "arm,juno-sram-ns", "mmio-sram"; + reg = <0x0 0x2e000000 0x0 0x8000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x0 0x2e000000 0x8000>; + + cpu_scp_lpri: scp-shmem@0 { + compatible = "arm,juno-scp-shmem"; + reg = <0x0 0x200>; + }; + + cpu_scp_hpri: scp-shmem@200 { + compatible = "arm,juno-scp-shmem"; + reg = <0x200 0x200>; + }; + }; + + scpi { + compatible = "arm,scpi"; + mboxes = <&mailbox 1>; + shmem = <&cpu_scp_hpri>; + + clocks { + compatible = "arm,scpi-clocks"; + + scpi_dvfs: scpi_clocks@0 { + compatible = "arm,scpi-dvfs-clocks"; + #clock-cells = <1>; + clock-indices = <0>, <1>, <2>; + clock-output-names = "atlclk", "aplclk","gpuclk"; + }; + scpi_clk: scpi_clocks@3 { + compatible = "arm,scpi-variable-clocks"; + #clock-cells = <1>; + clock-indices = <3>, <4>; + clock-output-names = "pxlclk0", "pxlclk1"; + }; + }; + + scpi_sensors0: sensors { + compatible = "arm,scpi-sensors"; + #thermal-sensor-cells = <1>; + }; + }; + /include/ "juno-clocks.dtsi" dma@7ff00000 { diff --git a/arch/arm64/boot/dts/arm/juno-motherboard.dtsi b/arch/arm64/boot/dts/arm/juno-motherboard.dtsi index 3c386680357e..413f1b9ebcd4 100644 --- a/arch/arm64/boot/dts/arm/juno-motherboard.dtsi +++ b/arch/arm64/boot/dts/arm/juno-motherboard.dtsi @@ -103,6 +103,21 @@ }; }; + flash@0,00000000 { + /* 2 * 32MiB NOR Flash memory mounted on CS0 */ + compatible = "arm,vexpress-flash", "cfi-flash"; + linux,part-probe = "afs"; + reg = <0 0x00000000 0x04000000>; + bank-width = <4>; + /* + * Unfortunately, accessing the flash disturbs + * the CPU idle states (suspend) and CPU + * hotplug of the platform. For this reason, + * flash hardware access is disabled by default. + */ + status = "disabled"; + }; + ethernet@2,00000000 { compatible = "smsc,lan9118", "smsc,lan9115"; reg = <2 0x00000000 0x10000>; diff --git a/arch/arm64/boot/dts/arm/juno-r1.dts b/arch/arm64/boot/dts/arm/juno-r1.dts index 734e1272b19f..93bc3d7d51c0 100644 --- a/arch/arm64/boot/dts/arm/juno-r1.dts +++ b/arch/arm64/boot/dts/arm/juno-r1.dts @@ -34,12 +34,39 @@ #address-cells = <2>; #size-cells = <0>; + cpu-map { + cluster0 { + core0 { + cpu = <&A57_0>; + }; + core1 { + cpu = <&A57_1>; + }; + }; + + cluster1 { + core0 { + cpu = <&A53_0>; + }; + core1 { + cpu = <&A53_1>; + }; + core2 { + cpu = <&A53_2>; + }; + core3 { + cpu = <&A53_3>; + }; + }; + }; + A57_0: cpu@0 { compatible = "arm,cortex-a57","arm,armv8"; reg = <0x0 0x0>; device_type = "cpu"; enable-method = "psci"; next-level-cache = <&A57_L2>; + clocks = <&scpi_dvfs 0>; }; A57_1: cpu@1 { @@ -48,6 +75,7 @@ device_type = "cpu"; enable-method = "psci"; next-level-cache = <&A57_L2>; + clocks = <&scpi_dvfs 0>; }; A53_0: cpu@100 { @@ -56,6 +84,7 @@ device_type = "cpu"; enable-method = "psci"; next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; }; A53_1: cpu@101 { @@ -64,6 +93,7 @@ device_type = "cpu"; enable-method = "psci"; next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; }; A53_2: cpu@102 { @@ -72,6 +102,7 @@ device_type = "cpu"; enable-method = "psci"; next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; }; A53_3: cpu@103 { @@ -80,6 +111,7 @@ device_type = "cpu"; enable-method = "psci"; next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; }; A57_L2: l2-cache0 { @@ -113,6 +145,26 @@ #include "juno-base.dtsi" + pcie-controller@40000000 { + compatible = "arm,juno-r1-pcie", "plda,xpressrich3-axi", "pci-host-ecam-generic"; + device_type = "pci"; + reg = <0 0x40000000 0 0x10000000>; /* ECAM config space */ + bus-range = <0 255>; + linux,pci-domain = <0>; + #address-cells = <3>; + #size-cells = <2>; + dma-coherent; + ranges = <0x01000000 0x00 0x5f800000 0x00 0x5f800000 0x0 0x00800000>, + <0x02000000 0x00 0x50000000 0x00 0x50000000 0x0 0x08000000>, + <0x42000000 0x40 0x00000000 0x40 0x00000000 0x1 0x00000000>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &gic 0 0 0 136 4>, + <0 0 0 2 &gic 0 0 0 137 4>, + <0 0 0 3 &gic 0 0 0 138 4>, + <0 0 0 4 &gic 0 0 0 139 4>; + msi-parent = <&v2m_0>; + }; }; &memtimer { diff --git a/arch/arm64/boot/dts/arm/juno.dts b/arch/arm64/boot/dts/arm/juno.dts index ffa05aeab3c7..53442b5ee4ff 100644 --- a/arch/arm64/boot/dts/arm/juno.dts +++ b/arch/arm64/boot/dts/arm/juno.dts @@ -34,12 +34,39 @@ #address-cells = <2>; #size-cells = <0>; + cpu-map { + cluster0 { + core0 { + cpu = <&A57_0>; + }; + core1 { + cpu = <&A57_1>; + }; + }; + + cluster1 { + core0 { + cpu = <&A53_0>; + }; + core1 { + cpu = <&A53_1>; + }; + core2 { + cpu = <&A53_2>; + }; + core3 { + cpu = <&A53_3>; + }; + }; + }; + A57_0: cpu@0 { compatible = "arm,cortex-a57","arm,armv8"; reg = <0x0 0x0>; device_type = "cpu"; enable-method = "psci"; next-level-cache = <&A57_L2>; + clocks = <&scpi_dvfs 0>; }; A57_1: cpu@1 { @@ -48,6 +75,7 @@ device_type = "cpu"; enable-method = "psci"; next-level-cache = <&A57_L2>; + clocks = <&scpi_dvfs 0>; }; A53_0: cpu@100 { @@ -56,6 +84,7 @@ device_type = "cpu"; enable-method = "psci"; next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; }; A53_1: cpu@101 { @@ -64,6 +93,7 @@ device_type = "cpu"; enable-method = "psci"; next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; }; A53_2: cpu@102 { @@ -72,6 +102,7 @@ device_type = "cpu"; enable-method = "psci"; next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; }; A53_3: cpu@103 { @@ -80,6 +111,7 @@ device_type = "cpu"; enable-method = "psci"; next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; }; A57_L2: l2-cache0 { diff --git a/arch/arm64/boot/dts/arm/vexpress-v2f-1xv7-ca53x2.dts b/arch/arm64/boot/dts/arm/vexpress-v2f-1xv7-ca53x2.dts index 5b1d0181023b..bb3c26d1154d 100644 --- a/arch/arm64/boot/dts/arm/vexpress-v2f-1xv7-ca53x2.dts +++ b/arch/arm64/boot/dts/arm/vexpress-v2f-1xv7-ca53x2.dts @@ -186,6 +186,6 @@ <0 0 41 &gic GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>, <0 0 42 &gic GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; - /include/ "../../../../arm/boot/dts/vexpress-v2m-rs1.dtsi" + /include/ "vexpress-v2m-rs1.dtsi" }; }; diff --git a/arch/arm64/boot/dts/arm/vexpress-v2m-rs1.dtsi b/arch/arm64/boot/dts/arm/vexpress-v2m-rs1.dtsi new file mode 120000 index 000000000000..68fd0f8f1dee --- /dev/null +++ b/arch/arm64/boot/dts/arm/vexpress-v2m-rs1.dtsi @@ -0,0 +1 @@ +../../../../arm/boot/dts/vexpress-v2m-rs1.dtsi
\ No newline at end of file diff --git a/arch/arm64/boot/dts/exynos/exynos7-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos7-pinctrl.dtsi index 2eef4a279131..f77ddaf21d04 100644 --- a/arch/arm64/boot/dts/exynos/exynos7-pinctrl.dtsi +++ b/arch/arm64/boot/dts/exynos/exynos7-pinctrl.dtsi @@ -586,3 +586,106 @@ samsung,pin-drv = <2>; }; }; + +&pinctrl_bus1 { + gpf0: gpf0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpf1: gpf1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpf2: gpf2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpf3: gpf3 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpf4: gpf4 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpf5: gpf5 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpg1: gpg1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpg2: gpg2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gph1: gph1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpv6: gpv6 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + spi5_bus: spi5-bus { + samsung,pins = "gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <3>; + samsung,pin-drv = <0>; + }; + + ufs_refclk_out: ufs-refclk-out { + samsung,pins = "gpg2-4"; + samsung,pin-function = <2>; + samsung,pin-pud = <0>; + samsung,pin-drv = <2>; + }; + + ufs_rst_n: ufs-rst-n { + samsung,pins = "gph1-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <3>; + samsung,pin-drv = <0>; + }; +}; diff --git a/arch/arm64/boot/dts/exynos/exynos7.dtsi b/arch/arm64/boot/dts/exynos/exynos7.dtsi index d7a37c3a6b52..f9c5a549c2c0 100644 --- a/arch/arm64/boot/dts/exynos/exynos7.dtsi +++ b/arch/arm64/boot/dts/exynos/exynos7.dtsi @@ -26,6 +26,7 @@ pinctrl5 = &pinctrl_ese; pinctrl6 = &pinctrl_fsys0; pinctrl7 = &pinctrl_fsys1; + pinctrl8 = &pinctrl_bus1; }; cpus { @@ -278,6 +279,12 @@ interrupts = <0 203 0>; }; + pinctrl_bus1: pinctrl@14870000 { + compatible = "samsung,exynos7-pinctrl"; + reg = <0x14870000 0x1000>; + interrupts = <0 384 0>; + }; + hsi2c_0: hsi2c@13640000 { compatible = "samsung,exynos7-hsi2c"; reg = <0x13640000 0x1000>; diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 4f2de3e789ee..c4957a4aa5aa 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -1,4 +1,6 @@ -dtb-$(CONFIG_ARCH_FSL_LS2085A) += fsl-ls2085a-simu.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb always := $(dtb-y) subdir-y := $(dts-dirs) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts new file mode 100644 index 000000000000..4cb996d6e686 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts @@ -0,0 +1,204 @@ +/* + * Device Tree file for Freescale LS2080a QDS Board. + * + * Copyright (C) 2015, Freescale Semiconductor + * + * Bhupesh Sharma <bhupesh.sharma@freescale.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +/include/ "fsl-ls2080a.dtsi" + +/ { + model = "Freescale Layerscape 2080a QDS Board"; + compatible = "fsl,ls2080a-qds", "fsl,ls2080a"; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + }; + +}; + +&esdhc { + status = "okay"; +}; + +&ifc { + status = "okay"; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0x0 0x0 0x5 0x80000000 0x08000000 + 0x2 0x0 0x5 0x30000000 0x00010000 + 0x3 0x0 0x5 0x20000000 0x00010000>; + + nor@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x8000000>; + bank-width = <2>; + device-width = <1>; + }; + + nand@2,0 { + compatible = "fsl,ifc-nand"; + reg = <0x2 0x0 0x10000>; + }; + + cpld@3,0 { + reg = <0x3 0x0 0x10000>; + compatible = "fsl,ls2080aqds-fpga", "fsl,fpga-qixis"; + }; +}; + +&i2c0 { + status = "okay"; + pca9547@77 { + compatible = "nxp,pca9547"; + reg = <0x77>; + #address-cells = <1>; + #size-cells = <0>; + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x00>; + rtc@68 { + compatible = "dallas,ds3232"; + reg = <0x68>; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x02>; + + ina220@40 { + compatible = "ti,ina220"; + reg = <0x40>; + shunt-resistor = <500>; + }; + + ina220@41 { + compatible = "ti,ina220"; + reg = <0x41>; + shunt-resistor = <1000>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x3>; + + adt7481@4c { + compatible = "adi,adt7461"; + reg = <0x4c>; + }; + }; + }; +}; + +&i2c1 { + status = "disabled"; +}; + +&i2c2 { + status = "disabled"; +}; + +&i2c3 { + status = "disabled"; +}; + +&dspi { + status = "okay"; + dflash0: n25q128a { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <3000000>; + reg = <0>; + }; + dflash1: sst25wf040b { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <3000000>; + reg = <1>; + }; + dflash2: en25s64 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <3000000>; + reg = <2>; + }; +}; + +&qspi { + status = "okay"; + qflash0: s25fl008k { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <20000000>; + reg = <0>; + }; +}; + +&sata0 { + status = "okay"; +}; + +&sata1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts new file mode 100644 index 000000000000..e127f0baab19 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts @@ -0,0 +1,166 @@ +/* + * Device Tree file for Freescale LS2080a RDB Board. + * + * Copyright (C) 2015, Freescale Semiconductor + * + * Bhupesh Sharma <bhupesh.sharma@freescale.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +/include/ "fsl-ls2080a.dtsi" + +/ { + model = "Freescale Layerscape 2080a RDB Board"; + compatible = "fsl,ls2080a-rdb", "fsl,ls2080a"; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + }; +}; + +&esdhc { + status = "okay"; +}; + +&ifc { + status = "okay"; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0x0 0x0 0x5 0x80000000 0x08000000 + 0x2 0x0 0x5 0x30000000 0x00010000 + 0x3 0x0 0x5 0x20000000 0x00010000>; + + nor@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x8000000>; + bank-width = <2>; + device-width = <1>; + }; + + nand@2,0 { + compatible = "fsl,ifc-nand"; + reg = <0x2 0x0 0x10000>; + }; + + cpld@3,0 { + reg = <0x3 0x0 0x10000>; + compatible = "fsl,ls2080aqds-fpga", "fsl,fpga-qixis"; + }; + +}; + +&i2c0 { + status = "okay"; + pca9547@75 { + compatible = "nxp,pca9547"; + reg = <0x75>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x01>; + rtc@68 { + compatible = "dallas,ds3232"; + reg = <0x68>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x3>; + + adt7481@4c { + compatible = "adi,adt7461"; + reg = <0x4c>; + }; + }; + }; +}; + +&i2c1 { + status = "disabled"; +}; + +&i2c2 { + status = "disabled"; +}; + +&i2c3 { + status = "disabled"; +}; + +&dspi { + status = "okay"; + dflash0: n25q512a { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <3000000>; + reg = <0>; + }; +}; + +&qspi { + status = "disabled"; +}; + +&sata0 { + status = "okay"; +}; + +&sata1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2085a-simu.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-simu.dts index 82e2a6fccc64..505d038078a3 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls2085a-simu.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-simu.dts @@ -1,7 +1,7 @@ /* - * Device Tree file for Freescale LS2085a software Simulator model + * Device Tree file for Freescale LS2080a software Simulator model * - * Copyright (C) 2014, Freescale Semiconductor + * Copyright (C) 2014-2015, Freescale Semiconductor * * Bhupesh Sharma <bhupesh.sharma@freescale.com> * @@ -20,11 +20,6 @@ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * - * You should have received a copy of the GNU General Public - * License along with this library; if not, write to the Free - * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, - * MA 02110-1301 USA - * * Or, alternatively, * * b) Permission is hereby granted, free of charge, to any person @@ -51,11 +46,16 @@ /dts-v1/; -/include/ "fsl-ls2085a.dtsi" +/include/ "fsl-ls2080a.dtsi" / { - model = "Freescale Layerscape 2085a software Simulator model"; - compatible = "fsl,ls2085a-simu", "fsl,ls2085a"; + model = "Freescale Layerscape 2080a software Simulator model"; + compatible = "fsl,ls2080a-simu", "fsl,ls2080a"; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + }; ethernet@2210000 { compatible = "smsc,lan91c111"; @@ -63,3 +63,8 @@ interrupts = <0 58 0x1>; }; }; + +&ifc { + status = "okay"; +}; + diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi new file mode 100644 index 000000000000..e81cd48d6245 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi @@ -0,0 +1,515 @@ +/* + * Device Tree Include file for Freescale Layerscape-2080A family SoC. + * + * Copyright (C) 2014-2015, Freescale Semiconductor + * + * Bhupesh Sharma <bhupesh.sharma@freescale.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/ { + compatible = "fsl,ls2080a"; + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + /* + * We expect the enable-method for cpu's to be "psci", but this + * is dependent on the SoC FW, which will fill this in. + * + * Currently supported enable-method is psci v0.2 + */ + + /* We have 4 clusters having 2 Cortex-A57 cores each */ + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x0>; + clocks = <&clockgen 1 0>; + }; + + cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x1>; + clocks = <&clockgen 1 0>; + }; + + cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x100>; + clocks = <&clockgen 1 1>; + }; + + cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x101>; + clocks = <&clockgen 1 1>; + }; + + cpu@200 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x200>; + clocks = <&clockgen 1 2>; + }; + + cpu@201 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x201>; + clocks = <&clockgen 1 2>; + }; + + cpu@300 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x300>; + clocks = <&clockgen 1 3>; + }; + + cpu@301 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x301>; + clocks = <&clockgen 1 3>; + }; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x00000000 0x80000000 0 0x80000000>; + /* DRAM space - 1, size : 2 GB DRAM */ + }; + + sysclk: sysclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + clock-output-names = "sysclk"; + }; + + gic: interrupt-controller@6000000 { + compatible = "arm,gic-v3"; + reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */ + <0x0 0x06100000 0 0x100000>, /* GICR (RD_base + SGI_base) */ + <0x0 0x0c0c0000 0 0x2000>, /* GICC */ + <0x0 0x0c0d0000 0 0x1000>, /* GICH */ + <0x0 0x0c0e0000 0 0x20000>; /* GICV */ + #interrupt-cells = <3>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + interrupt-controller; + interrupts = <1 9 0x4>; + + its: gic-its@6020000 { + compatible = "arm,gic-v3-its"; + msi-controller; + reg = <0x0 0x6020000 0 0x20000>; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <1 13 0x8>, /* Physical Secure PPI, active-low */ + <1 14 0x8>, /* Physical Non-Secure PPI, active-low */ + <1 11 0x8>, /* Virtual PPI, active-low */ + <1 10 0x8>; /* Hypervisor PPI, active-low */ + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <1 7 0x8>; /* PMU PPI, Level low type */ + }; + + soc { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clockgen: clocking@1300000 { + compatible = "fsl,ls2080a-clockgen"; + reg = <0 0x1300000 0 0xa0000>; + #clock-cells = <2>; + clocks = <&sysclk>; + }; + + serial0: serial@21c0500 { + compatible = "fsl,ns16550", "ns16550a"; + reg = <0x0 0x21c0500 0x0 0x100>; + clocks = <&clockgen 4 3>; + interrupts = <0 32 0x4>; /* Level high type */ + }; + + serial1: serial@21c0600 { + compatible = "fsl,ns16550", "ns16550a"; + reg = <0x0 0x21c0600 0x0 0x100>; + clocks = <&clockgen 4 3>; + interrupts = <0 32 0x4>; /* Level high type */ + }; + + fsl_mc: fsl-mc@80c000000 { + compatible = "fsl,qoriq-mc"; + reg = <0x00000008 0x0c000000 0 0x40>, /* MC portal base */ + <0x00000000 0x08340000 0 0x40000>; /* MC control reg */ + }; + + smmu: iommu@5000000 { + compatible = "arm,mmu-500"; + reg = <0 0x5000000 0 0x800000>; + #global-interrupts = <12>; + interrupts = <0 13 4>, /* global secure fault */ + <0 14 4>, /* combined secure interrupt */ + <0 15 4>, /* global non-secure fault */ + <0 16 4>, /* combined non-secure interrupt */ + /* performance counter interrupts 0-7 */ + <0 211 4>, <0 212 4>, + <0 213 4>, <0 214 4>, + <0 215 4>, <0 216 4>, + <0 217 4>, <0 218 4>, + /* per context interrupt, 64 interrupts */ + <0 146 4>, <0 147 4>, + <0 148 4>, <0 149 4>, + <0 150 4>, <0 151 4>, + <0 152 4>, <0 153 4>, + <0 154 4>, <0 155 4>, + <0 156 4>, <0 157 4>, + <0 158 4>, <0 159 4>, + <0 160 4>, <0 161 4>, + <0 162 4>, <0 163 4>, + <0 164 4>, <0 165 4>, + <0 166 4>, <0 167 4>, + <0 168 4>, <0 169 4>, + <0 170 4>, <0 171 4>, + <0 172 4>, <0 173 4>, + <0 174 4>, <0 175 4>, + <0 176 4>, <0 177 4>, + <0 178 4>, <0 179 4>, + <0 180 4>, <0 181 4>, + <0 182 4>, <0 183 4>, + <0 184 4>, <0 185 4>, + <0 186 4>, <0 187 4>, + <0 188 4>, <0 189 4>, + <0 190 4>, <0 191 4>, + <0 192 4>, <0 193 4>, + <0 194 4>, <0 195 4>, + <0 196 4>, <0 197 4>, + <0 198 4>, <0 199 4>, + <0 200 4>, <0 201 4>, + <0 202 4>, <0 203 4>, + <0 204 4>, <0 205 4>, + <0 206 4>, <0 207 4>, + <0 208 4>, <0 209 4>; + mmu-masters = <&fsl_mc 0x300 0>; + }; + + dspi: dspi@2100000 { + status = "disabled"; + compatible = "fsl,vf610-dspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2100000 0x0 0x10000>; + interrupts = <0 26 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>; + clock-names = "dspi"; + spi-num-chipselects = <5>; + bus-num = <0>; + }; + + esdhc: esdhc@2140000 { + status = "disabled"; + compatible = "fsl,ls2080a-esdhc", "fsl,esdhc"; + reg = <0x0 0x2140000 0x0 0x10000>; + interrupts = <0 28 0x4>; /* Level high type */ + clock-frequency = <0>; /* Updated by bootloader */ + voltage-ranges = <1800 1800 3300 3300>; + sdhci,auto-cmd12; + bus-width = <4>; + }; + + gpio0: gpio@2300000 { + compatible = "fsl,qoriq-gpio"; + reg = <0x0 0x2300000 0x0 0x10000>; + interrupts = <0 36 0x4>; /* Level high type */ + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio1: gpio@2310000 { + compatible = "fsl,qoriq-gpio"; + reg = <0x0 0x2310000 0x0 0x10000>; + interrupts = <0 36 0x4>; /* Level high type */ + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio@2320000 { + compatible = "fsl,qoriq-gpio"; + reg = <0x0 0x2320000 0x0 0x10000>; + interrupts = <0 37 0x4>; /* Level high type */ + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio3: gpio@2330000 { + compatible = "fsl,qoriq-gpio"; + reg = <0x0 0x2330000 0x0 0x10000>; + interrupts = <0 37 0x4>; /* Level high type */ + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + i2c0: i2c@2000000 { + status = "disabled"; + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2000000 0x0 0x10000>; + interrupts = <0 34 0x4>; /* Level high type */ + clock-names = "i2c"; + clocks = <&clockgen 4 3>; + }; + + i2c1: i2c@2010000 { + status = "disabled"; + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2010000 0x0 0x10000>; + interrupts = <0 34 0x4>; /* Level high type */ + clock-names = "i2c"; + clocks = <&clockgen 4 3>; + }; + + i2c2: i2c@2020000 { + status = "disabled"; + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2020000 0x0 0x10000>; + interrupts = <0 35 0x4>; /* Level high type */ + clock-names = "i2c"; + clocks = <&clockgen 4 3>; + }; + + i2c3: i2c@2030000 { + status = "disabled"; + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2030000 0x0 0x10000>; + interrupts = <0 35 0x4>; /* Level high type */ + clock-names = "i2c"; + clocks = <&clockgen 4 3>; + }; + + ifc: ifc@2240000 { + compatible = "fsl,ifc", "simple-bus"; + reg = <0x0 0x2240000 0x0 0x20000>; + interrupts = <0 21 0x4>; /* Level high type */ + little-endian; + #address-cells = <2>; + #size-cells = <1>; + + ranges = <0 0 0x5 0x80000000 0x08000000 + 2 0 0x5 0x30000000 0x00010000 + 3 0 0x5 0x20000000 0x00010000>; + }; + + qspi: quadspi@20c0000 { + status = "disabled"; + compatible = "fsl,vf610-qspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x20c0000 0x0 0x10000>, + <0x0 0x20000000 0x0 0x10000000>; + reg-names = "QuadSPI", "QuadSPI-memory"; + interrupts = <0 25 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "qspi_en", "qspi"; + }; + + pcie@3400000 { + compatible = "fsl,ls2080a-pcie", "snps,dw-pcie"; + reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */ + 0x10 0x00000000 0x0 0x00002000>; /* configuration space */ + reg-names = "regs", "config"; + interrupts = <0 108 0x4>; /* Level high type */ + interrupt-names = "intr"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + num-lanes = <4>; + bus-range = <0x0 0xff>; + ranges = <0x81000000 0x0 0x00000000 0x10 0x00010000 0x0 0x00010000 /* downstream I/O */ + 0x82000000 0x0 0x40000000 0x10 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + msi-parent = <&its>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic 0 0 0 109 4>, + <0000 0 0 2 &gic 0 0 0 110 4>, + <0000 0 0 3 &gic 0 0 0 111 4>, + <0000 0 0 4 &gic 0 0 0 112 4>; + }; + + pcie@3500000 { + compatible = "fsl,ls2080a-pcie", "snps,dw-pcie"; + reg = <0x00 0x03500000 0x0 0x00100000 /* controller registers */ + 0x12 0x00000000 0x0 0x00002000>; /* configuration space */ + reg-names = "regs", "config"; + interrupts = <0 113 0x4>; /* Level high type */ + interrupt-names = "intr"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + num-lanes = <4>; + bus-range = <0x0 0xff>; + ranges = <0x81000000 0x0 0x00000000 0x12 0x00010000 0x0 0x00010000 /* downstream I/O */ + 0x82000000 0x0 0x40000000 0x12 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + msi-parent = <&its>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic 0 0 0 114 4>, + <0000 0 0 2 &gic 0 0 0 115 4>, + <0000 0 0 3 &gic 0 0 0 116 4>, + <0000 0 0 4 &gic 0 0 0 117 4>; + }; + + pcie@3600000 { + compatible = "fsl,ls2080a-pcie", "snps,dw-pcie"; + reg = <0x00 0x03600000 0x0 0x00100000 /* controller registers */ + 0x14 0x00000000 0x0 0x00002000>; /* configuration space */ + reg-names = "regs", "config"; + interrupts = <0 118 0x4>; /* Level high type */ + interrupt-names = "intr"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + num-lanes = <8>; + bus-range = <0x0 0xff>; + ranges = <0x81000000 0x0 0x00000000 0x14 0x00010000 0x0 0x00010000 /* downstream I/O */ + 0x82000000 0x0 0x40000000 0x14 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + msi-parent = <&its>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic 0 0 0 119 4>, + <0000 0 0 2 &gic 0 0 0 120 4>, + <0000 0 0 3 &gic 0 0 0 121 4>, + <0000 0 0 4 &gic 0 0 0 122 4>; + }; + + pcie@3700000 { + compatible = "fsl,ls2080a-pcie", "snps,dw-pcie"; + reg = <0x00 0x03700000 0x0 0x00100000 /* controller registers */ + 0x16 0x00000000 0x0 0x00002000>; /* configuration space */ + reg-names = "regs", "config"; + interrupts = <0 123 0x4>; /* Level high type */ + interrupt-names = "intr"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + num-lanes = <4>; + bus-range = <0x0 0xff>; + ranges = <0x81000000 0x0 0x00000000 0x16 0x00010000 0x0 0x00010000 /* downstream I/O */ + 0x82000000 0x0 0x40000000 0x16 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + msi-parent = <&its>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic 0 0 0 124 4>, + <0000 0 0 2 &gic 0 0 0 125 4>, + <0000 0 0 3 &gic 0 0 0 126 4>, + <0000 0 0 4 &gic 0 0 0 127 4>; + }; + + sata0: sata@3200000 { + status = "disabled"; + compatible = "fsl,ls2080a-ahci"; + reg = <0x0 0x3200000 0x0 0x10000>; + interrupts = <0 133 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>; + }; + + sata1: sata@3210000 { + status = "disabled"; + compatible = "fsl,ls2080a-ahci"; + reg = <0x0 0x3210000 0x0 0x10000>; + interrupts = <0 136 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>; + }; + + usb0: usb3@3100000 { + status = "disabled"; + compatible = "snps,dwc3"; + reg = <0x0 0x3100000 0x0 0x10000>; + interrupts = <0 80 0x4>; /* Level high type */ + dr_mode = "host"; + }; + + usb1: usb3@3110000 { + status = "disabled"; + compatible = "snps,dwc3"; + reg = <0x0 0x3110000 0x0 0x10000>; + interrupts = <0 81 0x4>; /* Level high type */ + dr_mode = "host"; + }; + + ccn@4000000 { + compatible = "arm,ccn-504"; + reg = <0x0 0x04000000 0x0 0x01000000>; + interrupts = <0 12 4>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2085a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2085a.dtsi deleted file mode 100644 index e281ceb338c3..000000000000 --- a/arch/arm64/boot/dts/freescale/fsl-ls2085a.dtsi +++ /dev/null @@ -1,163 +0,0 @@ -/* - * Device Tree Include file for Freescale Layerscape-2085A family SoC. - * - * Copyright (C) 2014, Freescale Semiconductor - * - * Bhupesh Sharma <bhupesh.sharma@freescale.com> - * - * This file is dual-licensed: you can use it either under the terms - * of the GPLv2 or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This library is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This library is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public - * License along with this library; if not, write to the Free - * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, - * MA 02110-1301 USA - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ - -/ { - compatible = "fsl,ls2085a"; - interrupt-parent = <&gic>; - #address-cells = <2>; - #size-cells = <2>; - - cpus { - #address-cells = <2>; - #size-cells = <0>; - - /* - * We expect the enable-method for cpu's to be "psci", but this - * is dependent on the SoC FW, which will fill this in. - * - * Currently supported enable-method is psci v0.2 - */ - - /* We have 4 clusters having 2 Cortex-A57 cores each */ - cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x0 0x0>; - }; - - cpu@1 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x0 0x1>; - }; - - cpu@100 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x0 0x100>; - }; - - cpu@101 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x0 0x101>; - }; - - cpu@200 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x0 0x200>; - }; - - cpu@201 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x0 0x201>; - }; - - cpu@300 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x0 0x300>; - }; - - cpu@301 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x0 0x301>; - }; - }; - - memory@80000000 { - device_type = "memory"; - reg = <0x00000000 0x80000000 0 0x80000000>; - /* DRAM space - 1, size : 2 GB DRAM */ - }; - - gic: interrupt-controller@6000000 { - compatible = "arm,gic-v3"; - reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */ - <0x0 0x06100000 0 0x100000>; /* GICR (RD_base + SGI_base) */ - #interrupt-cells = <3>; - interrupt-controller; - interrupts = <1 9 0x4>; - }; - - timer { - compatible = "arm,armv8-timer"; - interrupts = <1 13 0x8>, /* Physical Secure PPI, active-low */ - <1 14 0x8>, /* Physical Non-Secure PPI, active-low */ - <1 11 0x8>, /* Virtual PPI, active-low */ - <1 10 0x8>; /* Hypervisor PPI, active-low */ - }; - - serial0: serial@21c0500 { - device_type = "serial"; - compatible = "fsl,ns16550", "ns16550a"; - reg = <0x0 0x21c0500 0x0 0x100>; - clock-frequency = <0>; /* Updated by bootloader */ - interrupts = <0 32 0x1>; /* edge triggered */ - }; - - serial1: serial@21c0600 { - device_type = "serial"; - compatible = "fsl,ns16550", "ns16550a"; - reg = <0x0 0x21c0600 0x0 0x100>; - clock-frequency = <0>; /* Updated by bootloader */ - interrupts = <0 32 0x1>; /* edge triggered */ - }; - - fsl_mc: fsl-mc@80c000000 { - compatible = "fsl,qoriq-mc"; - reg = <0x00000008 0x0c000000 0 0x40>, /* MC portal base */ - <0x00000000 0x08340000 0 0x40000>; /* MC control reg */ - }; -}; diff --git a/arch/arm64/boot/dts/hisilicon/Makefile b/arch/arm64/boot/dts/hisilicon/Makefile index fa81a6ee6473..cd158b80e29b 100644 --- a/arch/arm64/boot/dts/hisilicon/Makefile +++ b/arch/arm64/boot/dts/hisilicon/Makefile @@ -1,4 +1,4 @@ -dtb-$(CONFIG_ARCH_HISI) += hi6220-hikey.dtb +dtb-$(CONFIG_ARCH_HISI) += hi6220-hikey.dtb hip05-d02.dtb always := $(dtb-y) subdir-y := $(dts-dirs) diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts index e36a539468a5..8d43a0fce522 100644 --- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts +++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts @@ -17,11 +17,14 @@ compatible = "hisilicon,hi6220-hikey", "hisilicon,hi6220"; aliases { - serial0 = &uart0; + serial0 = &uart0; /* On board UART0 */ + serial1 = &uart1; /* BT UART */ + serial2 = &uart2; /* LS Expansion UART0 */ + serial3 = &uart3; /* LS Expansion UART1 */ }; chosen { - stdout-path = "serial0:115200n8"; + stdout-path = "serial3:115200n8"; }; memory@0 { diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi index 3f03380815b6..82d2488a0e86 100644 --- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi @@ -5,6 +5,7 @@ */ #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/hi6220-clock.h> / { compatible = "hisilicon,hi6220"; @@ -164,8 +165,48 @@ compatible = "arm,pl011", "arm,primecell"; reg = <0x0 0xf8015000 0x0 0x1000>; interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ao_ctrl 36>, <&ao_ctrl 36>; + clocks = <&ao_ctrl HI6220_UART0_PCLK>, + <&ao_ctrl HI6220_UART0_PCLK>; clock-names = "uartclk", "apb_pclk"; }; + + uart1: uart@f7111000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0 0xf7111000 0x0 0x1000>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&sys_ctrl HI6220_UART1_PCLK>, + <&sys_ctrl HI6220_UART1_PCLK>; + clock-names = "uartclk", "apb_pclk"; + status = "disabled"; + }; + + uart2: uart@f7112000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0 0xf7112000 0x0 0x1000>; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&sys_ctrl HI6220_UART2_PCLK>, + <&sys_ctrl HI6220_UART2_PCLK>; + clock-names = "uartclk", "apb_pclk"; + status = "disabled"; + }; + + uart3: uart@f7113000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0 0xf7113000 0x0 0x1000>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&sys_ctrl HI6220_UART3_PCLK>, + <&sys_ctrl HI6220_UART3_PCLK>; + clock-names = "uartclk", "apb_pclk"; + }; + + uart4: uart@f7114000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0 0xf7114000 0x0 0x1000>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&sys_ctrl HI6220_UART4_PCLK>, + <&sys_ctrl HI6220_UART4_PCLK>; + clock-names = "uartclk", "apb_pclk"; + status = "disabled"; + }; }; }; diff --git a/arch/arm64/boot/dts/hisilicon/hip05-d02.dts b/arch/arm64/boot/dts/hisilicon/hip05-d02.dts new file mode 100644 index 000000000000..ae34e250456f --- /dev/null +++ b/arch/arm64/boot/dts/hisilicon/hip05-d02.dts @@ -0,0 +1,36 @@ +/** + * dts file for Hisilicon D02 Development Board + * + * Copyright (C) 2014,2015 Hisilicon Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * publishhed by the Free Software Foundation. + * + */ + +/dts-v1/; + +#include "hip05.dtsi" + +/ { + model = "Hisilicon Hip05 D02 Development Board"; + compatible = "hisilicon,hip05-d02"; + + memory@00000000 { + device_type = "memory"; + reg = <0x0 0x00000000 0x0 0x80000000>; + }; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + status = "ok"; +}; diff --git a/arch/arm64/boot/dts/hisilicon/hip05.dtsi b/arch/arm64/boot/dts/hisilicon/hip05.dtsi new file mode 100644 index 000000000000..4ff16d016e34 --- /dev/null +++ b/arch/arm64/boot/dts/hisilicon/hip05.dtsi @@ -0,0 +1,271 @@ +/** + * dts file for Hisilicon D02 Development Board + * + * Copyright (C) 2014,2015 Hisilicon Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * publishhed by the Free Software Foundation. + * + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> + +/ { + compatible = "hisilicon,hip05-d02"; + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + psci { + compatible = "arm,psci-0.2"; + method = "smc"; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu-map { + cluster0 { + core0 { + cpu = <&cpu0>; + }; + core1 { + cpu = <&cpu1>; + }; + core2 { + cpu = <&cpu2>; + }; + core3 { + cpu = <&cpu3>; + }; + }; + cluster1 { + core0 { + cpu = <&cpu4>; + }; + core1 { + cpu = <&cpu5>; + }; + core2 { + cpu = <&cpu6>; + }; + core3 { + cpu = <&cpu7>; + }; + }; + cluster2 { + core0 { + cpu = <&cpu8>; + }; + core1 { + cpu = <&cpu9>; + }; + core2 { + cpu = <&cpu10>; + }; + core3 { + cpu = <&cpu11>; + }; + }; + cluster3 { + core0 { + cpu = <&cpu12>; + }; + core1 { + cpu = <&cpu13>; + }; + core2 { + cpu = <&cpu14>; + }; + core3 { + cpu = <&cpu15>; + }; + }; + }; + + cpu0: cpu@20000 { + device_type = "cpu"; + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x20000>; + enable-method = "psci"; + }; + + cpu1: cpu@20001 { + device_type = "cpu"; + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x20001>; + enable-method = "psci"; + }; + + cpu2: cpu@20002 { + device_type = "cpu"; + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x20002>; + enable-method = "psci"; + }; + + cpu3: cpu@20003 { + device_type = "cpu"; + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x20003>; + enable-method = "psci"; + }; + + cpu4: cpu@20100 { + device_type = "cpu"; + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x20100>; + enable-method = "psci"; + }; + + cpu5: cpu@20101 { + device_type = "cpu"; + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x20101>; + enable-method = "psci"; + }; + + cpu6: cpu@20102 { + device_type = "cpu"; + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x20102>; + enable-method = "psci"; + }; + + cpu7: cpu@20103 { + device_type = "cpu"; + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x20103>; + enable-method = "psci"; + }; + + cpu8: cpu@20200 { + device_type = "cpu"; + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x20200>; + enable-method = "psci"; + }; + + cpu9: cpu@20201 { + device_type = "cpu"; + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x20201>; + enable-method = "psci"; + }; + + cpu10: cpu@20202 { + device_type = "cpu"; + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x20202>; + enable-method = "psci"; + }; + + cpu11: cpu@20203 { + device_type = "cpu"; + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x20203>; + enable-method = "psci"; + }; + + cpu12: cpu@20300 { + device_type = "cpu"; + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x20300>; + enable-method = "psci"; + }; + + cpu13: cpu@20301 { + device_type = "cpu"; + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x20301>; + enable-method = "psci"; + }; + + cpu14: cpu@20302 { + device_type = "cpu"; + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x20302>; + enable-method = "psci"; + }; + + cpu15: cpu@20303 { + device_type = "cpu"; + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x20303>; + enable-method = "psci"; + }; + }; + + gic: interrupt-controller@8d000000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <3>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + interrupt-controller; + #redistributor-regions = <1>; + redistributor-stride = <0x0 0x30000>; + reg = <0x0 0x8d000000 0 0x10000>, /* GICD */ + <0x0 0x8d100000 0 0x300000>, /* GICR */ + <0x0 0xfe000000 0 0x10000>, /* GICC */ + <0x0 0xfe010000 0 0x10000>, /* GICH */ + <0x0 0xfe020000 0 0x10000>; /* GICV */ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + + its_totems: interrupt-controller@8c000000 { + compatible = "arm,gic-v3-its"; + msi-controller; + reg = <0x0 0x8c000000 0x0 0x40000>; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; + }; + + soc { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + refclk200mhz: refclk200mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <200000000>; + }; + + uart0: uart@80300000 { + compatible = "snps,dw-apb-uart"; + reg = <0x0 0x80300000 0x0 0x10000>; + interrupts = <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&refclk200mhz>; + clock-names = "apb_pclk"; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart1: uart@80310000 { + compatible = "snps,dw-apb-uart"; + reg = <0x0 0x80310000 0x0 0x10000>; + interrupts = <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&refclk200mhz>; + clock-names = "apb_pclk"; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + }; +}; diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile index e2f6afa7f849..348f4db4f313 100644 --- a/arch/arm64/boot/dts/marvell/Makefile +++ b/arch/arm64/boot/dts/marvell/Makefile @@ -1,4 +1,5 @@ dtb-$(CONFIG_ARCH_BERLIN) += berlin4ct-dmp.dtb +dtb-$(CONFIG_ARCH_BERLIN) += berlin4ct-stb.dtb always := $(dtb-y) subdir-y := $(dts-dirs) diff --git a/arch/arm64/boot/dts/marvell/berlin4ct-stb.dts b/arch/arm64/boot/dts/marvell/berlin4ct-stb.dts new file mode 100644 index 000000000000..348c37ecf069 --- /dev/null +++ b/arch/arm64/boot/dts/marvell/berlin4ct-stb.dts @@ -0,0 +1,66 @@ +/* + * Copyright (C) 2015 Marvell Technology Group Ltd. + * + * Author: Jisheng Zhang <jszhang@marvell.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "berlin4ct.dtsi" + +/ { + model = "Marvell BG4CT STB board"; + compatible = "marvell,berlin4ct-stb", "marvell,berlin4ct", "marvell,berlin"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + device_type = "memory"; + /* the first 16MB is for firmwares' usage */ + reg = <0 0x01000000 0 0x7f000000>; + }; +}; + +&uart0 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/marvell/berlin4ct.dtsi b/arch/arm64/boot/dts/marvell/berlin4ct.dtsi index dd4a10d605d9..a3b5f1d4a240 100644 --- a/arch/arm64/boot/dts/marvell/berlin4ct.dtsi +++ b/arch/arm64/boot/dts/marvell/berlin4ct.dtsi @@ -135,6 +135,96 @@ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; }; + apb@e80000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + + ranges = <0 0xe80000 0x10000>; + interrupt-parent = <&aic>; + + gpio0: gpio@0400 { + compatible = "snps,dw-apb-gpio"; + reg = <0x0400 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + porta: gpio-port@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0>; + }; + }; + + gpio1: gpio@0800 { + compatible = "snps,dw-apb-gpio"; + reg = <0x0800 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + portb: gpio-port@1 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <1>; + }; + }; + + gpio2: gpio@0c00 { + compatible = "snps,dw-apb-gpio"; + reg = <0x0c00 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + portc: gpio-port@2 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <2>; + }; + }; + + gpio3: gpio@1000 { + compatible = "snps,dw-apb-gpio"; + reg = <0x1000 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + portd: gpio-port@3 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <3>; + }; + }; + + aic: interrupt-controller@3800 { + compatible = "snps,dw-apb-ictl"; + reg = <0x3800 0x30>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + apb@fc0000 { compatible = "simple-bus"; #address-cells = <1>; @@ -151,6 +241,36 @@ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; }; + sm_gpio0: gpio@8000 { + compatible = "snps,dw-apb-gpio"; + reg = <0x8000 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + porte: gpio-port@4 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <32>; + reg = <0>; + }; + }; + + sm_gpio1: gpio@9000 { + compatible = "snps,dw-apb-gpio"; + reg = <0x9000 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + portf: gpio-port@5 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <32>; + reg = <0>; + }; + }; + uart0: uart@d000 { compatible = "snps,dw-apb-uart"; reg = <0xd000 0x100>; diff --git a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts index 4be66cadbc7c..811cb760ba49 100644 --- a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts +++ b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts @@ -387,6 +387,24 @@ }; }; +&pio { + spi_pins_a: spi0 { + pins_spi { + pinmux = <MT8173_PIN_69_SPI_CK__FUNC_SPI_CK_0_>, + <MT8173_PIN_70_SPI_MI__FUNC_SPI_MI_0_>, + <MT8173_PIN_71_SPI_MO__FUNC_SPI_MO_0_>, + <MT8173_PIN_72_SPI_CS__FUNC_SPI_CS_0_>; + }; + }; +}; + +&spi { + pinctrl-names = "default"; + pinctrl-0 = <&spi_pins_a>; + mediatek,pad-select = <0>; + status = "okay"; +}; + &uart0 { status = "okay"; }; diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi index 06a15644be38..4dd5f93d0303 100644 --- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi @@ -116,6 +116,13 @@ clock-output-names = "clk32k"; }; + cpum_ck: oscillator@2 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + clock-output-names = "cpum_ck"; + }; + timer { compatible = "arm,armv8-timer"; interrupt-parent = <&gic>; @@ -227,8 +234,10 @@ #power-domain-cells = <1>; reg = <0 0x10006000 0 0x1000>; clocks = <&clk26m>, - <&topckgen CLK_TOP_MM_SEL>; - clock-names = "mfg", "mm"; + <&topckgen CLK_TOP_MM_SEL>, + <&topckgen CLK_TOP_VENC_SEL>, + <&topckgen CLK_TOP_VENC_LT_SEL>; + clock-names = "mfg", "mm", "venc", "venc_lt"; infracfg = <&infracfg>; }; @@ -365,7 +374,20 @@ status = "disabled"; }; - i2c3: i2c3@11010000 { + spi: spi@1100a000 { + compatible = "mediatek,mt8173-spi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0 0x1100a000 0 0x1000>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_SYSPLL3_D2>, + <&topckgen CLK_TOP_SPI_SEL>, + <&pericfg CLK_PERI_SPI0>; + clock-names = "parent-clk", "sel-clk", "spi-clk"; + status = "disabled"; + }; + + i2c3: i2c@11010000 { compatible = "mediatek,mt8173-i2c"; reg = <0 0x11010000 0 0x70>, <0 0x11000280 0 0x80>; @@ -381,7 +403,7 @@ status = "disabled"; }; - i2c4: i2c4@11011000 { + i2c4: i2c@11011000 { compatible = "mediatek,mt8173-i2c"; reg = <0 0x11011000 0 0x70>, <0 0x11000300 0 0x80>; @@ -397,7 +419,7 @@ status = "disabled"; }; - i2c6: i2c6@11013000 { + i2c6: i2c@11013000 { compatible = "mediatek,mt8173-i2c"; reg = <0 0x11013000 0 0x70>, <0 0x11000080 0 0x80>; @@ -487,6 +509,36 @@ clock-names = "source", "hclk"; status = "disabled"; }; + + mmsys: clock-controller@14000000 { + compatible = "mediatek,mt8173-mmsys", "syscon"; + reg = <0 0x14000000 0 0x1000>; + #clock-cells = <1>; + }; + + imgsys: clock-controller@15000000 { + compatible = "mediatek,mt8173-imgsys", "syscon"; + reg = <0 0x15000000 0 0x1000>; + #clock-cells = <1>; + }; + + vdecsys: clock-controller@16000000 { + compatible = "mediatek,mt8173-vdecsys", "syscon"; + reg = <0 0x16000000 0 0x1000>; + #clock-cells = <1>; + }; + + vencsys: clock-controller@18000000 { + compatible = "mediatek,mt8173-vencsys", "syscon"; + reg = <0 0x18000000 0 0x1000>; + #clock-cells = <1>; + }; + + vencltsys: clock-controller@19000000 { + compatible = "mediatek,mt8173-vencltsys", "syscon"; + reg = <0 0x19000000 0 0x1000>; + #clock-cells = <1>; + }; }; }; diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi index 66804ffbc6d2..6b8abbe68746 100644 --- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi @@ -19,6 +19,7 @@ / { aliases { serial0 = &blsp1_uart2; + serial1 = &blsp1_uart1; }; chosen { @@ -33,6 +34,31 @@ pinctrl-1 = <&blsp1_uart2_sleep>; }; + i2c@78b6000 { + /* On Low speed expansion */ + status = "okay"; + }; + + i2c@78b8000 { + /* On High speed expansion */ + status = "okay"; + }; + + i2c@78ba000 { + /* On Low speed expansion */ + status = "okay"; + }; + + spi@78b7000 { + /* On High speed expansion */ + status = "okay"; + }; + + spi@78b9000 { + /* On Low speed expansion */ + status = "okay"; + }; + leds { pinctrl-names = "default"; pinctrl-0 = <&msmgpio_leds>, @@ -85,3 +111,7 @@ }; }; }; + +&sdhc_1 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8916-pins.dtsi b/arch/arm64/boot/dts/qcom/msm8916-pins.dtsi index 568956859088..49ec55a37614 100644 --- a/arch/arm64/boot/dts/qcom/msm8916-pins.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916-pins.dtsi @@ -13,6 +13,30 @@ &msmgpio { + blsp1_uart1_default: blsp1_uart1_default { + pinmux { + function = "blsp_uart1"; + pins = "gpio0", "gpio1"; + }; + pinconf { + pins = "gpio0", "gpio1"; + drive-strength = <16>; + bias-disable; + }; + }; + + blsp1_uart1_sleep: blsp1_uart1_sleep { + pinmux { + function = "gpio"; + pins = "gpio0", "gpio1"; + }; + pinconf { + pins = "gpio0", "gpio1"; + drive-strength = <2>; + bias-pull-down; + }; + }; + blsp1_uart2_default: blsp1_uart2_default { pinmux { function = "blsp_uart2"; @@ -27,7 +51,7 @@ blsp1_uart2_sleep: blsp1_uart2_sleep { pinmux { - function = "blsp_uart2"; + function = "gpio"; pins = "gpio4", "gpio5"; }; pinconf { @@ -241,6 +265,30 @@ }; }; + i2c2_default: i2c2_default { + pinmux { + function = "blsp_i2c2"; + pins = "gpio6", "gpio7"; + }; + pinconf { + pins = "gpio6", "gpio7"; + drive-strength = <2>; + bias-disable = <0>; + }; + }; + + i2c2_sleep: i2c2_sleep { + pinmux { + function = "gpio"; + pins = "gpio6", "gpio7"; + }; + pinconf { + pins = "gpio6", "gpio7"; + drive-strength = <2>; + bias-disable = <0>; + }; + }; + i2c4_default: i2c4_default { pinmux { function = "blsp_i2c4"; @@ -255,7 +303,7 @@ i2c4_sleep: i2c4_sleep { pinmux { - function = "blsp_i2c4"; + function = "gpio"; pins = "gpio14", "gpio15"; }; pinconf { @@ -265,6 +313,30 @@ }; }; + i2c6_default: i2c6_default { + pinmux { + function = "blsp_i2c6"; + pins = "gpio22", "gpio23"; + }; + pinconf { + pins = "gpio22", "gpio23"; + drive-strength = <2>; + bias-disable = <0>; + }; + }; + + i2c6_sleep: i2c6_sleep { + pinmux { + function = "gpio"; + pins = "gpio22", "gpio23"; + }; + pinconf { + pins = "gpio22", "gpio23"; + drive-strength = <2>; + bias-disable = <0>; + }; + }; + sdhc2_cd_pin { sdc2_cd_on: cd_on { pinmux { diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi index 5911de008dd5..8d184ff19642 100644 --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi @@ -99,9 +99,19 @@ compatible = "qcom,gcc-msm8916"; #clock-cells = <1>; #reset-cells = <1>; + #power-domain-cells = <1>; reg = <0x1800000 0x80000>; }; + blsp1_uart1: serial@78af000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x78af000 0x200>; + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + blsp1_uart2: serial@78b0000 { compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; reg = <0x78b0000 0x200>; @@ -224,6 +234,21 @@ status = "disabled"; }; + blsp_i2c2: i2c@78b6000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x78b6000 0x1000>; + interrupts = <GIC_SPI 96 0>; + clocks = <&gcc GCC_BLSP1_AHB_CLK>, + <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>; + clock-names = "iface", "core"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c2_default>; + pinctrl-1 = <&i2c2_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + blsp_i2c4: i2c@78b8000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0x78b8000 0x1000>; @@ -239,6 +264,21 @@ status = "disabled"; }; + blsp_i2c6: i2c@78ba000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x78ba000 0x1000>; + interrupts = <GIC_SPI 100 0>; + clocks = <&gcc GCC_BLSP1_AHB_CLK>, + <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>; + clock-names = "iface", "core"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c6_default>; + pinctrl-1 = <&i2c6_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + sdhc_1: sdhci@07824000 { compatible = "qcom,sdhci-msm-v4"; reg = <0x07824900 0x11c>, <0x07824000 0x800>; @@ -390,6 +430,13 @@ interrupt-controller; #interrupt-cells = <4>; }; + + rng@22000 { + compatible = "qcom,prng"; + reg = <0x00022000 0x200>; + clocks = <&gcc GCC_PRNG_AHB_CLK>; + clock-names = "core"; + }; }; }; diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index 5f760347aee2..3c4d4ce59918 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -34,11 +34,12 @@ CONFIG_MODULE_UNLOAD=y CONFIG_ARCH_BCM_IPROC=y CONFIG_ARCH_BERLIN=y CONFIG_ARCH_EXYNOS7=y -CONFIG_ARCH_FSL_LS2085A=y +CONFIG_ARCH_LAYERSCAPE=y CONFIG_ARCH_HISI=y CONFIG_ARCH_MEDIATEK=y CONFIG_ARCH_ROCKCHIP=y CONFIG_ARCH_SEATTLE=y +CONFIG_ARCH_STRATIX10=y CONFIG_ARCH_TEGRA=y CONFIG_ARCH_TEGRA_132_SOC=y CONFIG_ARCH_QCOM=y @@ -49,6 +50,7 @@ CONFIG_ARCH_XGENE=y CONFIG_ARCH_ZYNQMP=y CONFIG_PCI=y CONFIG_PCI_MSI=y +CONFIG_PCI_HOST_GENERIC=y CONFIG_PCI_XGENE=y CONFIG_SMP=y CONFIG_SCHED_MC=y diff --git a/drivers/clk/samsung/clk-exynos5250.c b/drivers/clk/samsung/clk-exynos5250.c index 55b83c7ef878..5bebf8cb0d70 100644 --- a/drivers/clk/samsung/clk-exynos5250.c +++ b/drivers/clk/samsung/clk-exynos5250.c @@ -222,9 +222,13 @@ PNAME(mout_mpll_user_p) = { "fin_pll", "mout_mpll" }; PNAME(mout_bpll_user_p) = { "fin_pll", "mout_bpll" }; PNAME(mout_aclk166_p) = { "mout_cpll", "mout_mpll_user" }; PNAME(mout_aclk200_p) = { "mout_mpll_user", "mout_bpll_user" }; +PNAME(mout_aclk300_p) = { "mout_aclk300_disp1_mid", + "mout_aclk300_disp1_mid1" }; PNAME(mout_aclk400_p) = { "mout_aclk400_g3d_mid", "mout_gpll" }; PNAME(mout_aclk200_sub_p) = { "fin_pll", "div_aclk200" }; PNAME(mout_aclk266_sub_p) = { "fin_pll", "div_aclk266" }; +PNAME(mout_aclk300_sub_p) = { "fin_pll", "div_aclk300_disp" }; +PNAME(mout_aclk300_disp1_mid1_p) = { "mout_vpll", "mout_cpll" }; PNAME(mout_aclk333_sub_p) = { "fin_pll", "div_aclk333" }; PNAME(mout_aclk400_isp_sub_p) = { "fin_pll", "div_aclk400_isp" }; PNAME(mout_hdmi_p) = { "div_hdmi_pixel", "sclk_hdmiphy" }; @@ -303,9 +307,13 @@ static struct samsung_mux_clock exynos5250_mux_clks[] __initdata = { */ MUX(0, "mout_aclk166", mout_aclk166_p, SRC_TOP0, 8, 1), MUX(0, "mout_aclk200", mout_aclk200_p, SRC_TOP0, 12, 1), + MUX(0, "mout_aclk300_disp1_mid", mout_aclk200_p, SRC_TOP0, 14, 1), + MUX(0, "mout_aclk300", mout_aclk300_p, SRC_TOP0, 15, 1), MUX(0, "mout_aclk333", mout_aclk166_p, SRC_TOP0, 16, 1), MUX(0, "mout_aclk400_g3d_mid", mout_aclk200_p, SRC_TOP0, 20, 1), + MUX(0, "mout_aclk300_disp1_mid1", mout_aclk300_disp1_mid1_p, SRC_TOP1, + 8, 1), MUX(0, "mout_aclk400_isp", mout_aclk200_p, SRC_TOP1, 24, 1), MUX(0, "mout_aclk400_g3d", mout_aclk400_p, SRC_TOP1, 28, 1), @@ -316,7 +324,10 @@ static struct samsung_mux_clock exynos5250_mux_clks[] __initdata = { MUX(0, "mout_bpll_user", mout_bpll_user_p, SRC_TOP2, 24, 1), MUX(CLK_MOUT_GPLL, "mout_gpll", mout_gpll_p, SRC_TOP2, 28, 1), - MUX(0, "mout_aclk200_disp1_sub", mout_aclk200_sub_p, SRC_TOP3, 4, 1), + MUX(CLK_MOUT_ACLK200_DISP1_SUB, "mout_aclk200_disp1_sub", + mout_aclk200_sub_p, SRC_TOP3, 4, 1), + MUX(CLK_MOUT_ACLK300_DISP1_SUB, "mout_aclk300_disp1_sub", + mout_aclk300_sub_p, SRC_TOP3, 6, 1), MUX(0, "mout_aclk266_gscl_sub", mout_aclk266_sub_p, SRC_TOP3, 8, 1), MUX(0, "mout_aclk_266_isp_sub", mout_aclk266_sub_p, SRC_TOP3, 16, 1), MUX(0, "mout_aclk_400_isp_sub", mout_aclk400_isp_sub_p, @@ -392,6 +403,7 @@ static struct samsung_div_clock exynos5250_div_clks[] __initdata = { DIV(0, "div_aclk333", "mout_aclk333", DIV_TOP0, 20, 3), DIV(0, "div_aclk400_g3d", "mout_aclk400_g3d", DIV_TOP0, 24, 3), + DIV(0, "div_aclk300_disp", "mout_aclk300", DIV_TOP0, 28, 3), DIV(0, "div_aclk400_isp", "mout_aclk400_isp", DIV_TOP1, 20, 3), DIV(0, "div_aclk66_pre", "mout_mpll_user", DIV_TOP1, 24, 3), diff --git a/include/dt-bindings/clock/exynos5250.h b/include/dt-bindings/clock/exynos5250.h index 8183d1c237d9..15508adcdfde 100644 --- a/include/dt-bindings/clock/exynos5250.h +++ b/include/dt-bindings/clock/exynos5250.h @@ -173,8 +173,10 @@ /* mux clocks */ #define CLK_MOUT_HDMI 1024 #define CLK_MOUT_GPLL 1025 +#define CLK_MOUT_ACLK200_DISP1_SUB 1026 +#define CLK_MOUT_ACLK300_DISP1_SUB 1027 /* must be greater than maximal clock id */ -#define CLK_NR_CLKS 1026 +#define CLK_NR_CLKS 1028 #endif /* _DT_BINDINGS_CLOCK_EXYNOS_5250_H */ |