BMC/Intel-BMC/linux.git/include/media/cec.h, branch dev-4.18

media: cec: fix the Signal Free Time calculation

2018-11-13T19:12:50+00:00

commit 7d867a1b765e2b70815fec4964d7822a976ed349 upstream. The calculation of the Signal Free Time in the framework was not correct. If a message was received, then the next transmit should be considered a New Initiator and use a shorter SFT value. This was not done with the result that if both sides where continually sending messages, they both could use the same SFT value and one side could deny the other side access to the bus. Note that this fix does not take the corner case into account where a receive is in progress when you call adap_transmit. Signed-off-by: Hans Verkuil Cc: # for v4.18 and up Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Greg Kroah-Hartman

media: cec: make cec_get_edid_spa_location() an inline function

2018-11-13T19:12:49+00:00

commit b915bf575d5b7774d0f22d57d6c143e07dcaade2 upstream. This function is needed by both V4L2 and CEC, so move this to cec.h as a static inline since there are no obvious shared modules between the two subsystems. This patch, together with the following ones, fixes a dependency bug: if CEC_CORE is disabled, then building adv7604 (and other HDMI receivers) will fail because an essential function is now stubbed out. Signed-off-by: Hans Verkuil Cc: # for v4.17 and up Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Greg Kroah-Hartman

media: cec: improve CEC pin event handling

2018-03-22T12:16:52+00:00

It turns out that the struct cec_fh event buffer size of 64 events (64 for CEC_EVENT_PIN_CEC_LOW and 64 for _HIGH) is too small. It's about 160 ms worth of events and if the Raspberry Pi is busy, then it might take too long for the application to be scheduled so that it can drain the pending events. Increase these buffers to 800 events which is at least 2 seconds worth of events. There is also a FIFO in between the interrupt and the cec-pin thread. The thread passes the events on to the CEC core. It is important that should this FIFO fill up the cec core will be informed that events have been lost so this can be communicated to the user by setting CEC_EVENT_FL_DROPPED_EVENTS. It is very hard to debug CEC problems if events were lost without informing the user of that fact. If events were dropped due to the FIFO filling up, then the debugfs status file will let you know how many events were dropped. Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab

media: cec: add core error injection support

2018-03-22T11:59:31+00:00

Add two new ops (error_inj_show and error_inj_parse_line) to support error injection functionality for CEC adapters. If both are present, then the core will add a new error-inj debugfs file that can be used to see the current error injection commands and to set error injection commands. Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab

media: include/(uapi/)media: add SPDX license info

2018-02-14T18:23:51+00:00

Replace the old license information with the corresponding SPDX license for those headers that I authored. Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab

media: cec: move cec autorepeat handling to rc-core

2017-12-14T15:35:30+00:00

CEC autorepeat is different than other protocols. Autorepeat is triggered by the first repeated user control pressed CEC message, rather than a fixed REP_DELAY. This change also does away with the KEY_UP event directly after the first KEY_DOWN event, which was used to stop autorepeat from starting. See commit a9a249a2c997 ("media: cec: fix remote control passthrough") for the original change. Acked-by: Hans Verkuil Signed-off-by: Sean Young Signed-off-by: Mauro Carvalho Chehab

media: cec: disable the hardware when unregistered

2017-12-08T16:11:25+00:00

When the device is being unregistered disable the hardware, don't wait until cec_delete_adapter is called as the hardware may have disappeared by then. This would be the case for hotplugable devices. Signed-off-by: Hans Verkuil Reported-by: Bård Eirik Winther Tested-by: Bård Eirik Winther Signed-off-by: Mauro Carvalho Chehab

media: cec: add the adap_monitor_pin_enable op

2017-12-08T16:10:00+00:00

Some devices can monitor the CEC pin using an interrupt, but you only want to enable the interrupt if you actually switch to pin monitoring mode. So add a new op that is called when pin monitoring needs to be switched on or off. Also fix a small bug where the initial CEC pin event was sent again when calling S_MODE twice with the same CEC_MODE_MONITOR_PIN mode. Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab

media: cec.h: initialize parent and port in cec_phys_addr_validate

2017-09-23T18:59:44+00:00

Make sure these values are set to avoid 'uninitialized variable' warnings. Hasn't happened yet, but better safe than sorry. Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab

media: cec: add CEC_EVENT_PIN_HPD_LOW/HIGH events

2017-09-23T11:43:04+00:00

Add support for two new low-level events: PIN_HPD_LOW and PIN_HPD_HIGH. This is specifically meant for use with the upcoming cec-gpio driver and makes it possible to trace when the HPD pin changes. Some HDMI sinks do strange things with the HPD and this makes it easy to debug this. Note that this also moves the initialization of a devnode mutex and list to the allocate_adapter function: if the HPD is high, then as soon as the HPD interrupt is created an interrupt occurs and cec_queue_pin_hpd_event() is called which requires that the devnode mutex and list are initialized. Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab