BMC/Intel-BMC/linux.git/include/linux, branch v4.4.11

regulator: s2mps11: Fix invalid selector mask and voltages for buck9

2016-05-19T00:06:51+00:00

commit 3b672623079bb3e5685b8549e514f2dfaa564406 upstream. The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff instead of 0x1f) thus reading entire register as buck9's voltage. This effectively caused regulator core to interpret values as higher voltages than they were and then to set real voltage much lower than intended. The buck9 provides power to other regulators, including LDO13 and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower voltage caused SD card detection errors on Odroid XU3/XU4: mmc1: card never left busy state mmc1: error -110 whilst initialising SD card During driver probe the regulator core was checking whether initial voltage matches the constraints. With incorrect vsel_mask of 0xff and default value of 0x50, the core interpreted this as 5 V which is outside of constraints (3-3.775 V). Then the regulator core was adjusting the voltage to match the constraints. With incorrect vsel_mask this new voltage mapped to a vere low voltage in the driver. Signed-off-by: Krzysztof Kozlowski Reviewed-by: Javier Martinez Canillas Tested-by: Javier Martinez Canillas Signed-off-by: Mark Brown Signed-off-by: Greg Kroah-Hartman

vfs: add vfs_select_inode() helper

2016-05-19T00:06:48+00:00

commit 54d5ca871e72f2bb172ec9323497f01cd5091ec7 upstream. Signed-off-by: Miklos Szeredi Signed-off-by: Greg Kroah-Hartman

net: Implement net_dbg_ratelimited() for CONFIG_DYNAMIC_DEBUG case

2016-05-19T00:06:38+00:00

[ Upstream commit 2c94b53738549d81dc7464a32117d1f5112c64d3 ] Prior to commit d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op when !DEBUG") the implementation of net_dbg_ratelimited() was buggy for both the DEBUG and CONFIG_DYNAMIC_DEBUG cases. The bug was that net_ratelimit() was being called and, despite returning true, nothing was being printed to the console. This resulted in messages like the following - "net_ratelimit: %d callbacks suppressed" with no other output nearby. After commit d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op when !DEBUG") the bug is fixed for the DEBUG case. However, there's no output at all for CONFIG_DYNAMIC_DEBUG case. This patch restores debug output (if enabled) for the CONFIG_DYNAMIC_DEBUG case. Add a definition of net_dbg_ratelimited() for the CONFIG_DYNAMIC_DEBUG case. The implementation takes care to check that dynamic debugging is enabled before calling net_ratelimit(). Fixes: d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op when !DEBUG") Signed-off-by: Tim Bingham Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

bpf: fix refcnt overflow

2016-05-19T00:06:37+00:00

[ Upstream commit 92117d8443bc5afacc8d5ba82e541946310f106e ] On a system with >32Gbyte of phyiscal memory and infinite RLIMIT_MEMLOCK, the malicious application may overflow 32-bit bpf program refcnt. It's also possible to overflow map refcnt on 1Tb system. Impose 32k hard limit which means that the same bpf program or map cannot be shared by more than 32k processes. Fixes: 1be7f75d1668 ("bpf: enable non-root eBPF programs") Reported-by: Jann Horn Signed-off-by: Alexei Starovoitov Acked-by: Daniel Borkmann Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net/mlx5e: Device's mtu field is u16 and not int

2016-05-19T00:06:36+00:00

[ Upstream commit 046339eaab26804f52f6604877f5674f70815b26 ] For set/query MTU port firmware commands the MTU field is 16 bits, here I changed all the "int mtu" parameters of the functions wrapping those firmware commands to be u16. Signed-off-by: Saeed Mahameed Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

Minimal fix-up of bad hashing behavior of hash_64()

2016-05-11T09:21:13+00:00

commit 689de1d6ca95b3b5bd8ee446863bf81a4883ea25 upstream. This is a fairly minimal fixup to the horribly bad behavior of hash_64() with certain input patterns. In particular, because the multiplicative value used for the 64-bit hash was intentionally bit-sparse (so that the multiply could be done with shifts and adds on architectures without hardware multipliers), some bits did not get spread out very much. In particular, certain fairly common bit ranges in the input (roughly bits 12-20: commonly with the most information in them when you hash things like byte offsets in files or memory that have block factors that mean that the low bits are often zero) would not necessarily show up much in the result. There's a bigger patch-series brewing to fix up things more completely, but this is the fairly minimal fix for the 64-bit hashing problem. It simply picks a much better constant multiplier, spreading the bits out a lot better. NOTE! For 32-bit architectures, the bad old hash_64() remains the same for now, since 64-bit multiplies are expensive. The bigger hashing cleanup will replace the 32-bit case with something better. The new constants were picked by George Spelvin who wrote that bigger cleanup series. I just picked out the constants and part of the comment from that series. Cc: George Spelvin Cc: Thomas Gleixner Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman

clk-divider: make sure read-only dividers do not write to their register

2016-05-11T09:21:11+00:00

commit 50359819794b4a16ae35051cd80f2dab025f6019 upstream. Commit e6d5e7d90be9 ("clk-divider: Fix READ_ONLY when divider > 1") removed the special ops struct for read-only clocks and instead opted to handle them inside the regular ops. On the rk3368 this results in breakage as aclkm now gets set a value. While it is the same divider value, the A53 core still doesn't like it, which can result in the cpu ending up in a hang. The reason being that "ACLKENMasserts one clock cycle before the rising edge of ACLKM" and the clock should only be touched when STANDBYWFIL2 is asserted. To fix this, reintroduce the read-only ops but do include the round_rate callback. That way no writes that may be unsafe are done to the divider register in any case. The Rockchip use of the clk_divider_ops is adapted to this split again, as is the nxp, lpc18xx-ccu driver that was included since the original commit. On lpc18xx-ccu the divider seems to always be read-only so only uses the new ops now. Fixes: e6d5e7d90be9 ("clk-divider: Fix READ_ONLY when divider > 1") Reported-by: Zhang Qing Signed-off-by: Heiko Stuebner Signed-off-by: Stephen Boyd Signed-off-by: Greg Kroah-Hartman

numa: fix /proc//numa_maps for THP

2016-05-04T21:48:49+00:00

commit 28093f9f34cedeaea0f481c58446d9dac6dd620f upstream. In gather_pte_stats() a THP pmd is cast into a pte, which is wrong because the layouts may differ depending on the architecture. On s390 this will lead to inaccurate numa_maps accounting in /proc because of misguided pte_present() and pte_dirty() checks on the fake pte. On other architectures pte_present() and pte_dirty() may work by chance, but there may be an issue with direct-access (dax) mappings w/o underlying struct pages when HAVE_PTE_SPECIAL is set and THP is available. In vm_normal_page() the fake pte will be checked with pte_special() and because there is no "special" bit in a pmd, this will always return false and the VM_PFNMAP | VM_MIXEDMAP checking will be skipped. On dax mappings w/o struct pages, an invalid struct page pointer would then be returned that can crash the kernel. This patch fixes the numa_maps THP handling by introducing new "_pmd" variants of the can_gather_numa_stats() and vm_normal_page() functions. Signed-off-by: Gerald Schaefer Cc: Naoya Horiguchi Cc: "Kirill A . Shutemov" Cc: Konstantin Khlebnikov Cc: Michal Hocko Cc: Vlastimil Babka Cc: Jerome Marchand Cc: Johannes Weiner Cc: Dave Hansen Cc: Mel Gorman Cc: Dan Williams Cc: Martin Schwidefsky Cc: Heiko Carstens Cc: Michael Holzheu Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman

cgroup, cpuset: replace cpuset_post_attach_flush() with cgroup_subsys->post_attach callback

2016-05-04T21:48:49+00:00

commit 5cf1cacb49aee39c3e02ae87068fc3c6430659b0 upstream. Since e93ad19d0564 ("cpuset: make mm migration asynchronous"), cpuset kicks off asynchronous NUMA node migration if necessary during task migration and flushes it from cpuset_post_attach_flush() which is called at the end of __cgroup_procs_write(). This is to avoid performing migration with cgroup_threadgroup_rwsem write-locked which can lead to deadlock through dependency on kworker creation. memcg has a similar issue with charge moving, so let's convert it to an official callback rather than the current one-off cpuset specific function. This patch adds cgroup_subsys->post_attach callback and makes cpuset register cpuset_post_attach_flush() as its ->post_attach. The conversion is mostly one-to-one except that the new callback is called under cgroup_mutex. This is to guarantee that no other migration operations are started before ->post_attach callbacks are finished. cgroup_mutex is one of the outermost mutex in the system and has never been and shouldn't be a problem. We can add specialized synchronization around __cgroup_procs_write() but I don't think there's any noticeable benefit. Signed-off-by: Tejun Heo Cc: Li Zefan Cc: Johannes Weiner Cc: Michal Hocko Signed-off-by: Greg Kroah-Hartman

IB/mlx5: Expose correct max_sge_rd limit

2016-05-04T21:48:48+00:00

commit 986ef95ecdd3eb6fa29433e68faa94c7624083be upstream. mlx5 devices (Connect-IB, ConnectX-4, ConnectX-4-LX) has a limitation where rdma read work queue entries cannot exceed 512 bytes. A rdma_read wqe needs to fit in 512 bytes: - wqe control segment (16 bytes) - rdma segment (16 bytes) - scatter elements (16 bytes each) So max_sge_rd should be: (512 - 16 - 16) / 16 = 30. Reported-by: Christoph Hellwig Tested-by: Christoph Hellwig Signed-off-by: Sagi Grimberg Signed-off-by: Leon Romanovsky Signed-off-by: Doug Ledford Signed-off-by: Greg Kroah-Hartman