BMC/Intel-BMC/linux.git/drivers/usb/core/hub.c, branch dev-4.17

usb: hub: Don't wait for connect state at resume for powered-off ports

2018-08-03T05:48:00+00:00

[ Upstream commit 5d111f5190848d6fb1c414dc57797efea3526a2f ] wait_for_connected() wait till a port change status to USB_PORT_STAT_CONNECTION, but this is not possible if the port is unpowered. The loop will only exit at timeout. Such case take place if an over-current incident happen while system is in S3. Then during resume wait_for_connected() will wait 2s, which may be noticeable by the user. Signed-off-by: Dominik Bozek Signed-off-by: Kuppuswamy Sathyanarayanan Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

usb: core: handle hub C_PORT_OVER_CURRENT condition

2018-07-28T05:57:17+00:00

commit 249a32b7eeb3edb6897dd38f89651a62163ac4ed upstream. Based on USB2.0 Spec Section 11.12.5, "If a hub has per-port power switching and per-port current limiting, an over-current on one port may still cause the power on another port to fall below specific minimums. In this case, the affected port is placed in the Power-Off state and C_PORT_OVER_CURRENT is set for the port, but PORT_OVER_CURRENT is not set." so let's check C_PORT_OVER_CURRENT too for over current condition. Fixes: 08d1dec6f405 ("usb:hub set hub->change_bits when over-current happens") Cc: Tested-by: Alessandro Antenucci Signed-off-by: Bin Liu Acked-by: Alan Stern Signed-off-by: Greg Kroah-Hartman

usb: do not reset if a low-speed or full-speed device timed out

2018-07-03T09:26:47+00:00

commit 6e01827ed93947895680fbdad68c072a0f4e2450 upstream. Some low-speed and full-speed devices (for example, bluetooth) do not have time to initialize. For them, ETIMEDOUT is a valid error. We need to give them another try. Otherwise, they will never be initialized correctly and in dmesg will be messages "Bluetooth: hci0 command 0x1002 tx timeout" or similars. Fixes: 264904ccc33c ("usb: retry reset if a device times out") Cc: stable Signed-off-by: Maxim Moseychuk Signed-off-by: Greg Kroah-Hartman

USB: Increment wakeup count on remote wakeup.

2018-04-22T12:45:11+00:00

On chromebooks we depend on wakeup count to identify the wakeup source. But currently USB devices do not increment the wakeup count when they trigger the remote wake. This patch addresses the same. Resume condition is reported differently on USB 2.0 and USB 3.0 devices. On USB 2.0 devices, a wake capable device, if wake enabled, drives resume signal to indicate a remote wake (USB 2.0 spec section 7.1.7.7). The upstream facing port then sets C_PORT_SUSPEND bit and reports a port change event (USB 2.0 spec section 11.24.2.7.2.3). Thus if a port has resumed before driving the resume signal from the host and C_PORT_SUSPEND is set, then the device attached to the given port might be the reason for the last system wakeup. Increment the wakeup count for the same. On USB 3.0 devices, a function may signal that it wants to exit from device suspend by sending a Function Wake Device Notification to the host (USB3.0 spec section 8.5.6.4) Thus on receiving the Function Wake, increment the wakeup count. Signed-off-by: Ravi Chandra Sadineni Acked-by: Alan Stern Cc: stable Signed-off-by: Greg Kroah-Hartman

USB: announce bcdDevice as well as idVendor, idProduct.

2018-03-25T10:50:44+00:00

Print bcdDevice which is used by vendors to identify different versions of the same product (or different versions of firmware). Adding this to the logs will be useful for support purposes. Match the %2x.%02x formatting that's used by lsusb -v for this same value. Signed-off-by: Benson Leung Signed-off-by: Greg Kroah-Hartman

usb: hub: Reduce warning to notice on power loss

2018-03-23T13:11:54+00:00

Currently we warn the user when the root hub lost power after resume, but the user cannot do anything about it so it should probably be a notice. This will reduce the noise in the console during suspend and resume, which is already quite significant in many systems. Signed-off-by: Tomeu Vizoso Signed-off-by: Greg Kroah-Hartman

usb: core: introduce per-port over-current counters

2018-03-22T12:07:05+00:00

For some userspace applications information on the number of over-current conditions at specific USB hub ports is relevant. In our case we have a series of USB hardware (using the cp210x driver) which communicates using a proprietary protocol. These devices sometimes trigger an over-current situation on some hubs. In case of such an over-current situation the USB devices offer an interface for reducing the max used power. As these conditions are quite rare and imply performance reductions of the device we don't want to reduce the max power always. Therefore give user-space applications the possibility to react adequately by introducing an over_current_counter in the usb port struct which is exported via sysfs. Signed-off-by: Richard Leitner Signed-off-by: Greg Kroah-Hartman

usb: Don't disable Latency tolerance Messaging (LTM) before port reset

2018-03-09T17:37:10+00:00

Disabing Latency Tolerance Messaging before port reset is unnecessary. LTM is automatically disabled at port reset. If host can't communicate with the device the LTM message will fail, and the hub driver will unnecessarily do a logical disconnect. Broken communication is ofter the reason for a reset in the first place. Additionally we can't guarantee device is in a configured state, epecially in reset-resume case when root hub lost power. LTM can't be modified unless device is in a configured state. Just remove LTM disabling before port reset. Details about LTM and port reset in USB 3 specification: USB 3 spec section 9.4.5 "The LTM Enable field can be modified by the SetFeature() and ClearFeature() requests using the LTM_ENABLE feature selector. This field is reset to zero when the device is reset." USB 3 spec section 9.4.1 "The device shall process a Clear Feature (U1_Enable or U2_Enable or LTM_Enable) only if the device is in the configured state." Signed-off-by: Mathias Nyman Acked-by: Alan Stern Signed-off-by: Greg Kroah-Hartman

Merge 4.15-rc4 into usb-next

2017-12-18T08:08:05+00:00

We want the USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman

usb: core: add support for USB_REQ_SET_ISOCH_DELAY

2017-12-15T19:45:43+00:00

USB SS and SSP hubs provide wHubDelay values on their hub descriptor which we should inform the USB Device about. The USB Specification 3.0 explains, on section 9.4.11, how to calculate the value and how to issue the request. Note that a USB_REQ_SET_ISOCH_DELAY is valid on all device states (Default, Address, Configured), we just *chose* to issue it from Address state right after successfully fetching the USB Device Descriptor. Signed-off-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman