BMC/Intel-BMC/linux.git/drivers/mmc/core, branch dev-5.2

Revert "mmc: core: do not retry CMD6 in __mmc_switch()"

2019-09-10T09:35:26+00:00

commit 8ad8e02c2fa70cfddc1ded53ba9001c9d444075d upstream. Turns out the commit 3a0681c7448b ("mmc: core: do not retry CMD6 in __mmc_switch()") breaks initialization of a Toshiba THGBMNG5 eMMC card, when using the meson-gx-mmc.c driver on a custom board based on Amlogic A113D. The CMD6 that switches the card into HS200 mode is then one that fails and according to the below printed messages from the log: [ 1.648951] mmc0: mmc_select_hs200 failed, error -84 [ 1.648988] mmc0: error -84 whilst initialising MMC card After some analyze, it turns out that adding a delay of ~5ms inside mmc_select_bus_width() but after mmc_compare_ext_csds() has been executed, also fixes the problem. Adding yet some more debug code, trying to figure out if potentially the card could be in a busy state, both by using CMD13 and ->card_busy() ops concluded that this was not the case. Therefore, let's simply revert the commit that dropped support for retrying of CMD6, as this also fixes the problem. Fixes: 3a0681c7448b ("mmc: core: do not retry CMD6 in __mmc_switch()") Cc: stable@vger.kernel.org Signed-off-by: Jan Kaisrlik Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: core: Fix init of SD cards reporting an invalid VDD range

2019-09-06T08:23:42+00:00

commit 72741084d903e65e121c27bd29494d941729d4a1 upstream. The OCR register defines the supported range of VDD voltages for SD cards. However, it has turned out that some SD cards reports an invalid voltage range, for example having bit7 set. When a host supports MMC_CAP2_FULL_PWR_CYCLE and some of the voltages from the invalid VDD range, this triggers the core to run a power cycle of the card to try to initialize it at the lowest common supported voltage. Obviously this fails, since the card can't support it. Let's fix this problem, by clearing invalid bits from the read OCR register for SD cards, before proceeding with the VDD voltage negotiation. Cc: stable@vger.kernel.org Reported-by: Philip Langdale Signed-off-by: Ulf Hansson Reviewed-by: Philip Langdale Tested-by: Philip Langdale Tested-by: Manuel Presnitz Signed-off-by: Greg Kroah-Hartman

mmc: mmc_spi: Enable stable writes

2019-08-06T17:08:15+00:00

commit 3a6ffb3c8c3274a39dc8f2514526e645c5d21753 upstream. While using the mmc_spi driver occasionally errors like this popped up: mmcblk0: error -84 transferring data end_request: I/O error, dev mmcblk0, sector 581756 I looked on the Internet for occurrences of the same problem and came across a helpful post [1]. It includes source code to reproduce the bug. There is also an analysis about the cause. During transmission data in the supplied buffer is being modified. Thus the previously calculated checksum is not correct anymore. After some digging I found out that device drivers are supposed to report they need stable writes. To fix this I set the appropriate flag at queue initialization if CRC checksumming is enabled for that SPI host. [1] https://groups.google.com/forum/#!msg/sim1/gLlzWeXGFr8/KevXinUXfc8J Signed-off-by: Andreas Koop [shihpo: Rebase on top of v5.3-rc1] Signed-off-by: ShihPo Hung Cc: Paul Walmsley CC: stable@vger.kernel.org Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx

2019-06-21T16:58:42+00:00

Pull still more SPDX updates from Greg KH: "Another round of SPDX updates for 5.2-rc6 Here is what I am guessing is going to be the last "big" SPDX update for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that were "easy" to determine by pattern matching. The ones after this are going to be a bit more difficult and the people on the spdx list will be discussing them on a case-by-case basis now. Another 5000+ files are fixed up, so our overall totals are: Files checked: 64545 Files with SPDX: 45529 Compared to the 5.1 kernel which was: Files checked: 63848 Files with SPDX: 22576 This is a huge improvement. Also, we deleted another 20000 lines of boilerplate license crud, always nice to see in a diffstat" * tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits) treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485 ...

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500

2019-06-19T15:09:55+00:00

Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner Reviewed-by: Enrico Weigelt Reviewed-by: Kate Stewart Reviewed-by: Allison Randal Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman

mmc: core: Prevent processing SDIO IRQs when the card is suspended

2019-06-18T12:06:32+00:00

Processing of SDIO IRQs must obviously be prevented while the card is system suspended, otherwise we may end up trying to communicate with an uninitialized SDIO card. Reports throughout the years shows that this is not only a theoretical problem, but a real issue. So, let's finally fix this problem, by keeping track of the state for the card and bail out before processing the SDIO IRQ, in case the card is suspended. Cc: stable@vger.kernel.org Reported-by: Douglas Anderson Tested-by: Douglas Anderson Signed-off-by: Ulf Hansson

mmc: core: Add sdio_retune_hold_now() and sdio_retune_release()

2019-06-18T11:30:32+00:00

We want SDIO drivers to be able to temporarily stop retuning when the driver knows that the SDIO card is not in a state where retuning will work (maybe because the card is asleep). We'll move the relevant functions to a place where drivers can call them. Cc: stable@vger.kernel.org #v4.18+ Signed-off-by: Douglas Anderson Acked-by: Adrian Hunter Acked-by: Kalle Valo Signed-off-by: Ulf Hansson

mmc: core: API to temporarily disable retuning for SDIO CRC errors

2019-06-18T11:30:21+00:00

Normally when the MMC core sees an "-EILSEQ" error returned by a host controller then it will trigger a retuning of the card. This is generally a good idea. However, if a command is expected to sometimes cause transfer errors then these transfer errors shouldn't cause a re-tuning. This re-tuning will be a needless waste of time. One example case where a transfer is expected to cause errors is when transitioning between idle (sometimes referred to as "sleep" in Broadcom code) and active state on certain Broadcom WiFi SDIO cards. Specifically if the card was already transitioning between states when the command was sent it could cause an error on the SDIO bus. Let's add an API that the SDIO function drivers can call that will temporarily disable the auto-tuning functionality. Then we can add a call to this in the Broadcom WiFi driver and any other driver that might have similar needs. NOTE: this makes the assumption that the card is already tuned well enough that it's OK to disable the auto-retuning during one of these error-prone situations. Presumably the driver code performing the error-prone transfer knows how to recover / retry from errors. ...and after we can get back to a state where transfers are no longer error-prone then we can enable the auto-retuning again. If we truly find ourselves in a case where the card needs to be retuned sometimes to handle one of these error-prone transfers then we can always try a few transfers first without auto-retuning and then re-try with auto-retuning if the first few fail. Without this change on rk3288-veyron-minnie I periodically see this in the logs of a machine just sitting there idle: dwmmc_rockchip ff0d0000.dwmmc: Successfully tuned phase to XYZ Cc: stable@vger.kernel.org #v4.18+ Signed-off-by: Douglas Anderson Acked-by: Adrian Hunter Acked-by: Kalle Valo Signed-off-by: Ulf Hansson

mmc: core: complete HS400 before checking status

2019-06-17T11:18:11+00:00

We don't have a reproducible error case, yet our BSP team suggested that the mmc_switch_status() command in mmc_select_hs400() should come after the callback into the driver completing HS400 setup. It makes sense to me because we want the status of a fully setup HS400, so it will increase the reliability of the mmc_switch_status() command. Reported-by: Yoshihiro Shimoda Signed-off-by: Wolfram Sang Fixes: ba6c7ac3a2f4 ("mmc: core: more fine-grained hooks for HS400 tuning") Signed-off-by: Ulf Hansson

mmc: also set max_segment_size in the device

2019-06-05T19:18:39+00:00

If we only set the max_segment_size on the queue an IOMMU merge might create bigger segments again, so limit the IOMMU merges as well. Signed-off-by: Christoph Hellwig Signed-off-by: Jens Axboe