BMC/Intel-BMC/linux.git/drivers/hwmon/Kconfig, branch dev-4.6

hwmon: Add Power8 OCC hwmon driver

2016-06-03T20:51:51+00:00

Adds a hwmon driver for BMC to monitor Power8 CPU sensors via On Chip Controller. Signed-off-by: Yi Li Signed-off-by: Joel Stanley

hwmon: Create an NSA320 hardware monitoring driver

2016-03-09T02:40:49+00:00

Create a driver to support the hardware monitoring chip present in the Zyxel NSA320 and some of the other Zyxel NAS devices. The driver reads fan speed and temperature from a suitably pre-programmed MCU on the device. Signed-off-by: Adam Baker [groeck: Dropped .owner field initialization] Signed-off-by: Guenter Roeck

hwmon: (ntc_thermistor) Add support for ncpXXxh103

2016-03-05T14:25:34+00:00

This patch adds support for the Murata NCP15XH103 thermistor series. Signed-off-by: Joseph McNally Signed-off-by: Guenter Roeck

hwmon: Add LTC2990 sensor driver

2016-03-05T14:25:34+00:00

This adds support for the Linear Technology LTC2990 I2C System Monitor. The LTC2990 supports a combination of voltage, current and temperature monitoring. This driver currently only supports reading two currents by measuring two differential voltages across series resistors, in addition to the Vcc supply voltage and internal temperature. This is sufficient to support the Topic Miami SOM which uses this chip to monitor the currents flowing into the FPGA and the CPU parts. Signed-off-by: Mike Looijmans Signed-off-by: Guenter Roeck

hwmon: (htu21) Remove driver

2015-12-18T16:20:59+00:00

HTU21 is now supported by IIO, and can be instantiated as hwmon driver using the iio-hwmon bridge. An explicit hwmon driver is no longer needed. Cc: William Markezana Cc: Ludovic Tancerel Cc: Jonathan Cameron Reviewed-by: Jean Delvare Signed-off-by: Guenter Roeck

hwmon: (sht15) Select CONFIG_BITREVERSE

2015-12-18T16:19:52+00:00

If CONFIG_BITREVERSE is not built-in, the sht15 driver fails to link: drivers/built-in.o: In function `sht15_crc8': drivers/hwmon/sht15.c:195: undefined reference to `byte_rev_table' This adds a Kconfig 'select' statement, like all other users of bitrev.h have it. Signed-off-by: Arnd Bergmann Fixes: 33836ee98533 ("hwmon:change sht15_reverse()") Signed-off-by: Guenter Roeck

hwmon: (scpi) add thermal-of dependency

2015-11-16T17:54:45+00:00

The newly added scpi thermal support is broken when the scpi driver is built-in but the thermal driver is a loadable module: drivers/built-in.o: In function `scpi_hwmon_probe': (.text+0x444d70): undefined reference to `thermal_zone_of_sensor_unregister' (.text+0x444d94): undefined reference to `thermal_zone_of_sensor_register' drivers/built-in.o: In function `scpi_hwmon_remove': (text+0x444e6c): undefined reference to `thermal_zone_of_sensor_unregister' This uses the same Kconfig trick that we have in a couple of other drivers already to ensure we can only select the driver in valid configurations when either THERMAL_OF is disabled, or when with a dependency on CONFIG_THERMAL that can force SCPI to be a loadable module in the case I was hitting. Signed-off-by: Arnd Bergmann Fixes: 68acc77a2d51 ("hwmon: Support thermal zones registration for SCP temperature sensors") Signed-off-by: Guenter Roeck

hwmon: (ina2xx) Fix build issue by selecting REGMAP_I2C

2015-11-16T05:52:39+00:00

Since a0de56c81fcf ("hwmon: (ina2xx) convert driver to using regmap") the driver requires REGMAP_I2C to build. Select it by default in Kconfig. Reported-by: Guo Chunrong Cc: Marc Titinger Signed-off-by: Li Yang Fixes: a0de56c81fcf ("hwmon: (ina2xx) convert driver to using regmap") Signed-off-by: Guenter Roeck

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2015-11-10T23:00:03+00:00

Pull ARM SoC driver updates from Olof Johansson: "As we've enabled multiplatform kernels on ARM, and greatly done away with the contents under arch/arm/mach-*, there's still need for SoC-related drivers to go somewhere. Many of them go in through other driver trees, but we still have drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code that might be shared between ARM and ARM64 (or just in general makes sense to not have under the architecture directory). This branch contains mostly such code: - Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate with power management blocks on these SoCs for use by clock, regulator and bus frequency drivers. - Allwinner Reduced Serial Bus driver, again used to communicate with PMICs. - Drivers for ARM's SCPI (System Control Processor). Not to be confused with PSCI (Power State Coordination Interface). SCPI is used to communicate with the assistant embedded cores doing power management, and we have yet to see how many of them will implement this for their hardware vs abstracting in other ways (or not at all like in the past). - To make confusion between SCPI and PSCI more likely, this release also includes an update of PSCI to interface version 1.0. - Rockchip support for power domains. - A driver to talk to the firmware on Raspberry Pi" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits) soc: qcom: smd-rpm: Correct size of outgoing message bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings ARM: bcm2835: add mutual inclusion protection drivers: psci: make PSCI 1.0 functions initialization version dependent dt-bindings: Correct paths in Rockchip power domains binding document soc: rockchip: power-domain: don't try to print the clock name in error case soc: qcom/smem: add HWSPINLOCK dependency clk: berlin: add cpuclk ARM: berlin: dts: add CLKID_CPU for BG2Q ARM: bcm2835: Add the Raspberry Pi firmware driver soc: qcom: smem: Move RPM message ram out of smem DT node soc: qcom: smd-rpm: Correct the active vs sleep state flagging soc: qcom: smd: delete unneeded of_node_put firmware: qcom-scm: build for correct architecture level soc: qcom: smd: Correct SMEM items for upper channels qcom-scm: add missing prototype for qcom_scm_is_available() qcom-scm: fix endianess issue in __qcom_scm_is_call_available soc: qcom: smd: Reject send of too big packets soc: qcom: smd: Handle big endian CPUs ...

Merge tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers

2015-10-14T15:07:32+00:00

Merge "ARM System Control and Power Interface(SCPI) support" from Sudeep Holla It adds support for the following features provided by SCP firmware using different subsystems in Linux: 1. SCPI mailbox protocol driver which using mailbox framework 2. Clocks provided by SCP using clock framework 3. CPU DVFS(cpufreq) using existing arm-big-little driver 4. SCPI based sensors including temperature sensors * tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux: hwmon: Support thermal zones registration for SCP temperature sensors hwmon: Support sensors exported via ARM SCP interface firmware: arm_scpi: Extend to support sensors Documentation: add DT bindings for ARM SCPI sensors cpufreq: arm_big_little: add SCPI interface driver clk: scpi: add support for cpufreq virtual device clk: add support for clocks provided by SCP(System Control Processor) firmware: add support for ARM System Control and Power Interface(SCPI) protocol Documentation: add DT binding for ARM System Control and Power Interface(SCPI) protocol