BMC/Intel-BMC/linux.git/drivers/hid/usbhid, branch dev-4.6

HID: Fix boot delay for Creative SB Omni Surround 5.1 with quirk

2016-04-25T14:23:26+00:00

Needed for v2 of the device firmware, otherwise kernel will stuck for few seconds and throw "usb_submit_urb(ctrl) failed: -1" early on system boot. Signed-off-by: Nazar Mokrynskyi Reviewed-by: Benjamin Tissoires Signed-off-by: Jiri Kosina

HID: usbhid: fix inconsistent reset/resume/reset-resume behavior

2016-03-24T14:26:20+00:00

The usbhid driver has inconsistently duplicated code in its post-reset, resume, and reset-resume pathways. reset-resume doesn't check HID_STARTED before trying to restart the I/O queues. resume fails to clear the HID_SUSPENDED flag if HID_STARTED isn't set. resume calls usbhid_restart_queues() with usbhid->lock held and the others call it without holding the lock. The first item in particular causes a problem following a reset-resume if the driver hasn't started up its I/O. URB submission fails because usbhid->urbin is NULL, and this triggers an unending reset-retry loop. This patch fixes the problem by creating a new subroutine, hid_restart_io(), to carry out all the common activities. It also adds some checks that were missing in the original code: After a reset, there's no need to clear any halted endpoints. After a resume, if a reset is pending there's no need to restart any I/O until the reset is finished. After a resume, if the interrupt-IN endpoint is halted there's no need to submit the input URB until the halt has been cleared. Signed-off-by: Alan Stern Reported-by: Daniel Fraga Tested-by: Daniel Fraga CC: Signed-off-by: Jiri Kosina

HID: usbhid: enable NO_INIT_REPORTS quirk for Semico USB Keykoard2

2016-03-10T17:20:24+00:00

The device which identifies itself as a "USB Keykoard" (no typo) with VID:PID 1a2c:0027 does not seem to be handling the reports initialization very well. This results in a "usb_submit_urb(ctrl) failed: -1" message from the kernel when connected, and a delay before its initialization. It can also cause the hang the system. This patch adds the quirk for this device, which causes the delay to disappear. It is named as "USB Keykoard2" because the "USB Keykoard" already exists. Signed-off-by: Daniel Bristot de Oliveira Signed-off-by: Jiri Kosina

HID: quirks: Add no_init_reports for AKAI midi controller

2016-01-29T15:38:20+00:00

The midi controller times-out while initializing reports, this causes boot to take an extra 10 seconds. The device descriptor advertises that it has an internal HID device but seems to not actually do anything useful. Signed-off-by: Stafford Horne Reviewed-by: Benjamin Tissoires Signed-off-by: Jiri Kosina

HID: add HID_QUIRK_NOGET to Quanta 3003 too

2016-01-21T13:13:01+00:00

dmesg shows a lot of: [ 1374.890348] hid-multitouch 0003:0408:3003.0007: usb_submit_urb(ctrl) failed: -1 [ 1384.916388] hid-multitouch 0003:0408:3003.0007: usb_submit_urb(ctrl) failed: -1 [ 1384.916432] hid-multitouch 0003:0408:3003.0007: timeout initializing reports Add the quirk and make the touchscreen happy. Signed-off-by: Benjamin Tissoires Tested-by: Jim lovell Signed-off-by: Jiri Kosina

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid

2016-01-15T00:20:42+00:00

Pull HID updates from Jiri Kosina: - appoint Benjamin Tissoires as co-maintainer / designated reviewer - sysfs report_descriptor visibility fix for unclaimed devices, from Andy Lutomirski - suspend/resume fixes for Sony driver from Frank Praznik - IRQ deadlock fix from Ioan-Adrian Ratiu - hid-i2c fixes affecting (at least) Yoga 900 from Mika Westerberg and Srinivas Pandruvada - a lot of new device support (especially, but not limited to, Wacom) and assorted small misc fixes - almost complete G920 support; the only bit that is missing is switching the device to HID mode automatically; Simon Wood and Michal Maly are working on it. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (46 commits) Revert "INPUT: xpad: switch Logitech G920 Wheel into HID mode" HID: sensor-hub: Add quirk for Lenovo Yoga 900 with ITE Chips HID: Add new PID for Microchip Pick16F1454 HID: wacom: Use correct report to query pen ID from INTUOSHT2 devices HID: i2c-hid: Prevent sending reports from racing with device reset HID: use kobj_to_dev() HID: wiimote: use dev_to_wii() HID: add a new helper to_hid_driver() HID: use to_hid_device() HID: move to_hid_device() to hid.h HID: usbhid: use to_usb_device HID: corsair: Convert to use module_hid_driver HID: input: ignore the battery in OKLICK Laser BTmouse HID: wacom: Fix pad button range for CINTIQ_COMPANION_2 HID: wacom: Fix touchring value reporting HID: wacom: Report 'strip2' values in ABS_RY HID: wacom: Limit touchstrip data to 13 bits HID: wacom: bitwise vs logical ORs HID: wacom: Apply lowres quirk to BAMBOO_TOUCH devices HID: enable hid device to suspend/resume asynchronously ...

Merge branches 'for-4.4/upstream-fixes', 'for-4.5/async-suspend', 'for-4.5/container-of-cleanups', 'for-4.5/core', 'for-4.5/i2c-hid', 'for-4.5/logitech', 'for-4.5/multitouch', 'for-4.5/sony', 'for-4.5/upstream' and 'for-4.5/wacom' into for-linus

2016-01-14T15:11:06+00:00

HID: usbhid: use to_usb_device

2015-12-28T12:13:20+00:00

Use to_usb_device() instead of open-coding it. Signed-off-by: Geliang Tang Signed-off-by: Jiri Kosina

Merge tag 'usb-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

2015-12-13T19:58:18+00:00

Pull USB driver fixes from Greg KH: "Here are a number of small USB fixes for 4.4-rc5. All of them have been in linux-next. The majority are gadget and phy issues, with a few new quirks and device ids added as well" * tag 'usb-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (32 commits) USB: add quirk for devices with broken LPM xhci: fix usb2 resume timing and races. usb: musb: fail with error when no DMA controller set usb: gadget: uvc: fix permissions of configfs attributes usb: musb: core: Fix pm runtime for deferred probe usb: phy: msm: fix a possible NULL dereference USB: host: ohci-at91: fix a crash in ohci_hcd_at91_overcurrent_irq usb: Quiet down false peer failure messages usb: xhci: fix config fail of FS hub behind a HS hub with MTT xhci: Fix memory leak in xhci_pme_acpi_rtd3_enable() usb: Use the USB_SS_MULT() macro to decode burst multiplier for log message USB: whci-hcd: add check for dma mapping error usb: core : hub: Fix BOS 'NULL pointer' kernel panic USB: quirks: Apply ALWAYS_POLL to all ELAN devices usb-storage: Fix scsi-sd failure "Invalid field in cdb" for USB adapter JMicron USB: quirks: Fix another ELAN touchscreen usb: dwc3: gadget: don't prestart interrupt endpoints USB: serial: Another Infineon flash loader USB ID USB: cdc_acm: Ignore Infineon Flash Loader utility USB: cp210x: Remove CP2110 ID from compatibility list ...

USB: quirks: Apply ALWAYS_POLL to all ELAN devices

2015-12-01T22:22:22+00:00

All ELAN hid devices seem to require the ALWAYS_POLL quirk. Let's use this quirk for all devices from this vendor, rather than maintaining a list of all its known product IDs. Tested-by: Adrien Vergé Signed-off-by: Adrien Vergé Reviewed-by: Benjamin Tissoires Reviewed-by: Jiri Kosina Signed-off-by: Greg Kroah-Hartman