BMC/Intel-BMC/linux.git/Documentation/devicetree/bindings/power/reset, branch dev-5.4

dt-bindings: mfd: mediatek: Add MT6323 Power Controller

2019-09-02T10:20:40+00:00

- Add Power Controller section to existing binding document. - Add MT6323 PWRC bindings document with example. Suggested-by: Frank Wunderlich Signed-off-by: Josef Friedl Signed-off-by: Frank Wunderlich Signed-off-by: Lee Jones

dt-bindings: power: reset: add document for NVMEM based reboot-mode

2019-06-25T21:49:57+00:00

Add the device tree bindings document for the NVMEM based reboot-mode driver. Signed-off-by: Nandor Han Reviewed-by: Rob Herring Signed-off-by: Sebastian Reichel

dt-bindings: power: reset: qcom: Add qcom,pm8998-pon compatibility line

2019-06-24T21:25:07+00:00

Update bindings to support for qcom,pm8998-pon which uses gen2 pon Cc: Andy Gross Cc: David Brown Cc: Bjorn Andersson Cc: Amit Pundir Cc: Rob Herring Cc: Mark Rutland Cc: Sebastian Reichel Cc: linux-arm-msm@vger.kernel.org Cc: devicetree@vger.kernel.org Reviewed-by: Bjorn Andersson Signed-off-by: John Stultz Signed-off-by: Sebastian Reichel

power: reset: syscon-reboot: add a mask property

2019-04-05T13:06:57+00:00

Make the syscon-reboot driver accept value and mask instead of just value. Prior to this patch, the property name for the value was 'mask'. If only the mask property is defined on a node, maintain compatibility by using it as the value. This patch is based on commit f2c199db477e ("power: reset: syscon-poweroff: add a mask property") and does the same change for the syscon-reboot driver. Signed-off-by: Martin Schiller Acked-by: Rob Herring Signed-off-by: Sebastian Reichel

dt-bindings: soc: Add ZynqMP PM bindings

2019-02-12T12:36:21+00:00

Add documentation to describe Xilinx ZynqMP power management bindings. Signed-off-by: Rajan Vaja Signed-off-by: Jolly Shah Reviewed-by: Rob Herring Signed-off-by: Michal Simek

power: reset: gpio-poweroff: add ability to specific active and inactive delays

2018-12-05T21:38:29+00:00

Similar to gpio-reset allow to specify active and inactive delays while keeping the 100ms defaults that were used previously all the time. The dt-properties are named the same as in gpio-reset but get an "-ms" suffix as properties should contain such a suffix specifying its unit. Signed-off-by: Heiko Stuebner Reviewed-by: Rob Herring Reviewed-by: Moritz Fischer Signed-off-by: Sebastian Reichel

power: reset: qcom-pon: Add pms405 pon support

2018-09-20T09:40:00+00:00

Update the binding and driver for pms405 pon. Signed-off-by: Vinod Koul Signed-off-by: Bjorn Andersson Signed-off-by: Sebastian Reichel

dt-bindings: power: reset: qcom: Add resin binding

2018-07-07T20:22:23+00:00

Resin is similar to pwrkey, add the description and example for resin bindings Signed-off-by: Vinod Koul Reviewed-by: Rob Herring Signed-off-by: Sebastian Reichel

dt-bindings: power: reset: Add qcom pon binding

2018-07-06T13:53:10+00:00

The Power On device for Qcom PM 8xxx is a MFD supporting pwrkey and resin along with the Android reboot-mode. Add the binding describing this. Suggested-by: Bjorn Andersson Reviewed-by: Bjorn Andersson Signed-off-by: Vinod Koul Reviewed-by: Rob Herring Signed-off-by: Sebastian Reichel

dt-bindings: power: reset: gpio-poweroff: Add 'timeout-ms' property

2018-03-09T16:14:32+00:00

Add 'timeout-ms' property to support boards where the 3s timeout that the current driver defaults to is too short. Signed-off-by: Moritz Fischer Reviewed-by: Rob Herring Signed-off-by: Sebastian Reichel